SMART-AVI XT-800 User Manual

© Copyright 2007 Smart-AVI, All Rights Reserved
Notice
The information contained in this document is subject to change without notice. Smart-AVI makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for any particular purpose.
No part of this document may be photocopied, reproduced or translated into another language with out prior written consent from Smart-AVI.
For the complete manual, visit www.smartavi.com.
Use CAT5 cable to broadcast high
resolution SXGA, Stereo Audio, RS232
and IR to 8 stations up to 1000ft
away.
XT-800
www.smartavi.com
User Manual
2840 N. Naomi Ave.
Burbank, California 91504
Phone: (818) 565-0011
Facsimile: (818) 565-0020
Technical Specifications
3MART!UDIO6IDEO)NTEGRATION
3MART!UDIO6IDEO)NTEGRATION
SNOITACIFICEPS008-TXSNOITACIFICEPS008-TX
SNOITACIFICEPS008-TX
SNOITACIFICEPS008-TXSNOITACIFICEPS008-TX
ataDAGVataDAGV
ataDAGV
ataDAGVataDAGV
tamroFSBVC,C/Y,VUY,BsGR,VHBGR
noituloseR
0021x0091otpU
)AGXS,AGX,AGVS,AG
V
epytrotcennoCtekcos51DH
oiduAoiduA
oiduA
oiduAoiduA
epyTlangiSdecnalabnuoeretS
rotcennoCtekcoskcajmm5.3
rewoPrew
oP
rewoP
rewoPrewoP
stnemeriuqeRA5.@CDV5
rotcennoC)ev+retnec(kcajCDmm1.2
lacisyhPlacisyhP
lacisyhP
lacisyhPlacisy
hP
snoisnemiD)sgephtiw1.3(mc7.2x8.11x22
thgieWsbl5.3
Sending an RS232 command to remoteSending an RS232 command to remote
Sending an RS232 command to remoteSending an RS232 command to remote
Sending an RS232 command to remote monitormonitor
monitormonitor
monitor
In order to send a command to a remote monitor, you will need to use The following query at 9600 baud rate; <CR>//M1<CR>
After sending this query, any command sent from the PC will go directly to monitor 1
To send a command to monitor 2 replace "M1" with "M2" etc...
To send the same command to all monitors ( but only monitor 1 will answer) Use the following command; <CR>//M0<CR>
*
<CR> = Carriage return
In Out In Out
RS232
Out 1-8
IR
Introduction
The XT800 range of products allows the extension of a wide range of video and audio formats, RS232, and IR up to 8 locations using Category 5 Unshielded Twisted Pair (UTP) cables.
With RS232 communication support, the XT800 allows users to send commands to single or multiple devices. This allows the user to change volume,
channel or turn on/off the remote LCD TV.
Features
Supports Dual Screens.Uses easy to install, inexpensive CAT-5/5e/6/7/8.
Output reaches up to 1,000 feet (300 m).
Resolutions up to 1900x1200.HDTV Compatible (720p, 1080i, 1080p)300 MHz Bandwidth.Sends high-resolution UXGA, Stereo Audio signals,
RS232 or IR from one source to 8 locations.
Compatible with VGA, XGA, Sun, MAC and SGISync Format / Polarity Preservation.Compatible with Line Level Stereo Audio Signals.High ground loop immunity.Built-in power surge and transient protection.Designated trimmer in the remote unit to
compensate for cable length.
Compact Metal Case Enclosure.External power supply.RS-232c communication support to single or mul
tiple displays.
IR command to single or multiple displays.
What’s in the box?
XT800XT800
XT800XT800
XT800
Please check package contents before installing.
Installation Diagram
XT800 Transmitter Installation Diagram
XT800 Receiver Installation Diagram
Adjusting and Tuning the SignalAdjusting and Tuning the Signal
Adjusting and Tuning the SignalAdjusting and Tuning the Signal
Adjusting and Tuning the Signal
In order to fine tune the signal, adjust the individual dials one at a time starting with GREEN, then BLUE, and lastly RED. As you turn the dials you will notice the colors slightly change as you increase or decrease the strength. All dials should be around the same distance.
Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable
Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable
Preparing & Connecting System CAT5 Cable
Following is the wiring standard for terminating CAT 5 cable using RJ-45 connector:
Pair 1 Pins 1 & 2 Pair 2 Pins 3 & 6 Pair 3 Pins 4 & 5 Pair 4 Pins 7 & 8
Connectors:Connectors:
Connectors:Connectors:
Connectors: RJ-45 Capacitance:Capacitance:
Capacitance:Capacitance:
Capacitance: 14 pf/ft (46.2 pf/m) Conductor Gauge:Conductor Gauge:
Conductor Gauge:Conductor Gauge:
Conductor Gauge: 24 AWG Impedance:Impedance:
Impedance:Impedance:
Impedance: 100 +/- 15 ohms
4 - Pair
Connecting The TransmitterConnecting The Transmitter
Connecting The TransmitterConnecting The Transmitter
Connecting The Transmitter
1. Connect the output of the computer video card to the video input of the transmitter using the included male to male video cable.
2. Connect the output of the computer audio card to the audio input of the transmitter using 3.5mm audio male to male audio cable.
3. Connect local monitor to the VGA out of the transmitter.
4. Connect external speakers to the transmitter’s audio out (Standard 3.5mm stereo miniplug).
5. In the back of the unit connect the CAT5 cable that will connect to the receiver (XT800-RX).
*NOTE: You can not use RS232 and IR at the same time.
Connecting The ReceiverConnecting The Receiver
Connecting The ReceiverConnecting The Receiver
Connecting The Receiver
1. Connect CAT5 cable (coming from the transmitter) to the back of the receiver.
2. Connect 1-4 display monitors to the VGA out connectors on the front of the receiver.
3. Connect 1-4 sets of external speakers to the audio output connections on the front of the unit. (Standard 3.5mm stereo Miniplug)
tnetnoCegakcaP008TXtnetnoCegakcaP008TX
tnetnoCegakcaP008TX
tnetnoCegakcaP008TXtnetnoCegakcaP008TX
ytQytQ
ytQ
ytQytQsmetIsmetI
smetI
smetIsmetI.oNtraP.oNtraP
.oNtraP
.oNtraP.oNtraP
1tinurettimsnarT008TXXT-008TX
1ylppusr
ewopcdtlov5SU-A1D5-SP
1)tf6(elbacAGVelamotelam51DDH60-MMAGV-CC
lanoitpOlanoitpO
lanoitpO
lanoitpOlanoitpO
1tinUrevieceRORPTXXR-ORPTX
1elbacgulpinimoeretsmm5.3oiduA60-MMAMM-CC
1revieceREYERIEYE-MS
1rettimERIDEL-MS
1elbac2
32SR'660-232SRCC
XT400
VGAOut
8lines
of CAT 5
XTPRORX
XTPRORX
XTPRORX
XTPRORX
XTPRORX
XTPRORX
XTPRORX
XTPRORX
XT800
Loading...