Smart Avi VCT-100 User Manual
Technical Specifications
© Copyright 2004 Smart-AVI, All Rights Reserved
P
ataDAGV
tamroFSBVC,C/Y,VUY,BsGR,VHBGR
noituloseR
epyTrotcennoCtekcos51DH
rewo
stnemeriuqeRCDV5
rotcennoCkcajCDmm1.2
lacisyhP
snoisnemiDmm32x08x59
thgieWgK21.0
SNOITACIFICEPSTACV
0021x0061otpU
AGXS,AGX,AGVS,AGV
Notice
The information contained in this document is
subject to change without notice. Smart-AVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and fitness for any particular
purpose.
Smart-AVI will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material.
No part of this document may be photocopied,
reproduced or translated into another language with
out prior written consent from Smart-AVI.
For the complete manual, visit www.smartavi.com.
3MART!UDIO6IDEO)NTEGRATION
3MART!UDIO6IDEO)NTEGRATION
User Manual
VCAT
2840 N. Naomi Ave.
Burbank, California 91504
Phone: (818) 565-0011
Facsimile: (818) 565-0020
Use a single CAT5 to broadcast high
resolution SXGA up to 1000ft (300 m)
www.smartavi.com
Introduction
The VCAT range of products allows the extension of a
wide range of video formats via a single Category 5
Unshielded Twisted Pair (UTP) cable. Using a unique
method of data transfer, the system allows a display
device to be situated up to 1000ft (300 meters) from
the source.
Features
Output reaches up to 1,000 feet.
Resolutions up to 1600 x 1200.
Sends high-resolution UXGA power signals over
single CAT5.
300 MHz Bandwidth.
Compatible with VGA, XGA, Sun, MAC and SGI.
Sync Format / Polarity Preservation.
High ground loop immunity.
Built-in lightning, power surge and transient
protection.
Remote Units come with Buffered Outputs.
Designated trimmer in the remote unit to
compensate for cable length.
What’s in the box?
Installation Diagram
VCAT Transmitter Installation Diagram
Connecting The TransmitterConnecting The Transmitter
Connecting The Transmitter
Connecting The TransmitterConnecting The Transmitter
1. Connect the output of the computer video card to the
video input of the transmitter using the included
male to male video cable.
2. Connect the CAT5 cable that will connect to the
receiver unit.
3. Connect the power supply.
VCAT Receiver Installation Diagram
Adjusting and Fine Tuning the SignalAdjusting and Fine Tuning the Signal
Adjusting and Fine Tuning the Signal
Adjusting and Fine Tuning the SignalAdjusting and Fine Tuning the Signal
In order to fine tune the
signal, adjust the individual
dials one at a time starting
with GREEN, then BLUE,
and lastly RED. As you turn
the dials you will notice the
colors slightly change as
you increase or decrease
the strength.
VCATVCAT
VCAT
VCATVCAT
Please check the contents of the package before
beginning installation.
tnetnoCegakcaP001-XLS
ytQsmetI.oNtraP
2CDV5SU-A1V5-SP
1tinUrevieceRTACVXR-TACV
1tinUrettimsnarTTACVXT-TACV
1elbacAGVelamotelam51DDHtf660-
Connecting The ReceiverConnecting The Receiver
Connecting The Receiver
Connecting The ReceiverConnecting The Receiver
1. Connect CAT5 cable (coming from the transmitter) to
the back of the receiver.
2. Connect the display monitor to the VGA out
connector on the front of the receiver.
3. Connect the power supply.
MMAGVS-CC
Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable
Preparing & Connecting System CAT5 Cable
Preparing & Connecting System CAT5 CablePreparing & Connecting System CAT5 Cable
Following is the wiring standard for terminating CAT 5
cable using RJ-45 connector:
Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8
Connectors:Connectors:
Connectors: RJ-45
Connectors:Connectors:
Capacitance:Capacitance:
Capacitance: 14 pf/ft (46.2 pf/m)
Capacitance:Capacitance:
Conductor Gauge:Conductor Gauge:
Conductor Gauge: 24 AWG
Conductor Gauge:Conductor Gauge:
Impedance:Impedance:
Impedance: 100 +/- 15 ohms
Impedance:Impedance:
4 - Pair
Loading...