User Manual
HDC-IR
www.smartavi.com
IR up to 1000ft away(333m)
Use a single CAT5 to broadcast
2840 N. Naomi Ave.
Phone: (818) 565-0011
Facsimile: (818) 565-0020
Burbank, California 91504
© Copyright 2008 Smart-AVI,All RightsReserved
Notice
HDC-IR SPECIFICATIONS
METI
Technical Specifications
The information contained in this document is
subject to change without notice. Smart-AVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
IR Frequency Range 30 KHz to 80KHz
IR Eye input
merchantability and fitness for any particular
purpose.
Smart-AVI willnot beliable forerrors contained herein
3.5mm stero jack
Cable Connector
Capture Distance Up to 25ft
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material.
IR Signal Indicator Green LED
No part of this document may be photocopied,
reproduced ortranslated intoanother language with
out prior written consent from Smart-AVI.
TTL
Signal Type
Power Requirements 5VDC 30mA
For the complete manual, visit www.smartavi.com.
Up to 10’
30KHz to 80KHz
IR Emitter output
IR Frequency Range
Emitter Distance
Red LED
Cable Connector 3.5mm mono jack
IR Signal Indicator
.25lb (0.9 Kg.)
12VDC 1A single power up to 250’
Box
Power Requirments
2.5”x2.5”x1.0”
Dimension
Cable Link CAT5 568A or 568B
Weight
sdradnatSgniriW5TAC
#niAP865AIT/AIBE865AIT/AIE
e1pirtsnee
rghtiwetiheWpirtsegnarohtiwetihW
n2eergdilosroepirtsetihwhtiwneerG egna
rodilosroepirtsetihwhtiweg
narO
3
epirtsegnarohtiwetihW
epirtsneerghtiwetihW
e4ulb
dilosroepirtsetihwhtiweulB eulbdilosroepirtsetihwhtiweulB
e5pirtseulbhtiwetiheWpir
tseulbhtiwetihW
6 egnarodilosroepirtsetihwhtiwegnarO dilosroepirtsetihwhtiwneerG
n7worbdilosroepirtsnworbhtiwetihW nworbdilosropirtsnworbhtiwetihW
n8worbdilosr
oepirtsetihwhtiwnworB nworbdilosroepirtsetihwhtiwnworB
HDC-IR can be used 2 ways,
1. enabling the remote side to control the DVD,
or any other source device. (the IR eye would
be connected at the remote).
2. enabling the source side to turn off or on the
remote TV/Monitor (the IR eye would be
connected at the source.
Installation Diagram
Connecting the IR
Use the Diagram for the IR connection.
Installation Instructions
1. Connect the IR LED to the IR window on the source
device.
2. Connect power supply to the unit. Observe LED
Connecting the Transmitter
lighting up indicating power present.
Operating Instructions
Once installation is completed, verify that the power is
present at all devices in the system. The peripheral
devices should be ready for use.
Connecting the Receiver
Connect IR LED to the IR window on the souce device.
2. Connect the IR Eye to the Receiver.
3. Observe LED lighting indicating power present.
Connect the Transmitter to the Receiver
Connect the transmitter to the receiver using
Category 5 UTP cable (Purchased separately). The
CAT 5 UTP cable, if purchased in
bulk, will be wired using 568A or
568B wiring standard. Once
connected, check that the power
LEDs on both the receiver and the
transmitter are on, IR status LED is on and RX LED is
flashing when Remote control is used indicating that
communication is in progress.
The HDC-IR range of products allow the extension
Introduction
of Infra Red control signals using single CAT5 UTP
(category 5, unshielded twisted pair) cable. The
HDC-IR is the first product for this application.
Uses easy to install, inexpensive CAT5.
Output reaches up to 1000 feet (300 m).
Sends IR and Power signals over CAT5
Features
protection.
High ground loop immunity.
Built-in lightning, power surge and transient
Optional power supply for remote unit.
Remote Units come with Buffered Outputs.
Compact Enclosure.
Fully compliant with standard modulated IR
and the latest IRDA.
Fully transparent path for all protocols and
Supports any IR Remote Control.
Bi-directional IR.
data transfers.
What’s in the box?
Please check the contents of the package before
beginning installation.
HDC-IR
IR Transmitter
HDC-IR-TX
ytQ metI noitpircseD
1
IR Receiver
IR Emitter
DEL-MS
HDC-IR-RX
1
1
IR Eye “Optional”
Power supply12VDC1A
EYE-MS
PS12VD1A
1
2
Loading...