Page 1
User
Manual
Sp
ecifications
V
i
DVI-D
esolution
z
e
)
e
h
T6 (STP)
1
T
ype
A
T
ype B
Audio
)
CA
l
Audio
l
T
ype Stero
Audio
b
m
,
V
)
)
W
)
b
i
A
b
a
k
,
50
8
2
deo Interface
R
Input Interfac
Upgradeabl
USB
B Data Data Rate of 12Mbps
B Connectors
RS232 and
RS232
rotoco
ower
Dimension (inches
ight (lbs
920 x 1200@60Hz, Resolution up to 1280 x
024 min. 75H
DVI-D (Single-Link
nboard Flas
Maximum Range 220ft
ompatable with USB version 1.
TX-DB9Female) (RX-DB9Male
TP
ull duplex, transparent to all baud rate
igna
Bandwidth 15MHz.0d
Impedance 100 Oh
onnector 3.5 mini jack
0/120
U (17” x 1.73”
l
DVX-4P
PIN 1
PIN 17
Please visit smartavi.com for a expanded version of this manual.
PIN 8
C 1
C 2
C 4
C 5
C 3
PIN 24
2840Naom
r
n
Facsimil: (818
(81
#niPlangiS#niPlangiS
1-2ataDS.D.M.6T1tceteDgulPtoH
2+2ataDS.D.M.7T1-0ataDS.D.M.T
4-4ataDS.D.M.9Td1leihS5
5+4ataDS.D.M.0T2-5ataDS.D.M.T
6kcolCCD1D2+5ataDS.D.M.T
7ataDCD2Dd2leihSkcolCS.D.M.T
8cnyS.treVgolan3A2+kcol
9-1ataDS.D.
M.4T2-kcolCS.D.M.T
01+1ataDS.D.M.T
1d1leihS3/1ataDS.D.M.1TCdeRgolanA
21-3ataDS.D.M.2TCneerGgolanA
31+
5VDC 1.6A
PV54+CcnySzroHgolanA
41rewo
51DN5GCdnuorGgolanA
v
ifornia1
-001
565-00
d3leihS4/2ataDS.D.M.8T1+0ataDS.D.M.T
3ataDS.D.M.3TCeulBgolanA
/0ataDS.D.M.T
CS.D.M.T
Extend 4 DVI-D, RS232, Stero Audio and USB1.1 using a
Single Rack Mount System.
m_dvx4p_093009
Page 2
Connection Diagram
TRANSMITTER
USB1.1
(on Front Panel)
6 STP Cable
220ft Max
RECEIVER
RS232
POWER
110V/120V
AUDIO
DVI (IN)
PC/MAC
Mouse/Keyboard
Connecting the DVI
1. Turn off computer and monitor.
2. Connect DVI male to male cable between the
computer and the transmitter.
3. Connect monitor or projector to the DVI port
on the receiver.
4.
Connect a shielded Cat 6 STP cable
between port 1 on the transmitter and port 1
on the receiver.
5. Repeat for 3 other ports.
Connecting the USB In/Out
1. Connect the transmitter to the host using the A-B
USB cable (included with the unit).
2. The A side of the connector would go to the computer host and the B side would be connected to
the transmitter.
3. Connect the receiver to the peripheral.
4. Connect the CAT6 STP Cable.
RS232
POWER
110V/120V
USB1.1
AUDIO
Connecting the Audio and RS232
1. Connect an RS232 cable and/or audio cable to the
souce unit.
2. Connect the Audio using 3.5mm cable at the transmitter
3. Connect the Speaker/s. at the Receiver.
4. Connect the last CAT6
STP Cable.
Preparing & Connecting System CAT5 Cable
Following is the wiring standard for terminating CAT 5
cable using RJ-45 connector:
Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8
Connectors: RJ-45
Capacitance: 14 pf/ft (46.2 pf/m)
Conductor Gauge: 24 AWG
Impedance: 100 +/- 15ohms
DVI (OUT)
Monitor
4 - Pair
The receiver provides remote power up to 500
Note:
mA to the connected peripherals. This power comes
from the host computer and is passed by the transmitter
to the receiver. In some applications, and external power
supply is required. SmartAVI can provide a power supply
for such cases with the receiver and transmitter units.
Connecting the TX/RX
1. Connect DVI, USB (In/Out) and Audio/RS232 as outlined.
2.Connect Power Cord.
3. Turn on TX and RX.
Loading...