Smart Avi DVX2P User Manual

Specifications

DVI

Video Interface DVI-D

Resolution 1920 x 1200@60Hz, Resolution up to 1280 x

1024 min. 75Hz

Input Interface DVI-D (Single-Link)

Upgradeable Onboard Flash

USB

CAT6 (STP) Maximum Range 220ft

USB Data Data Rate of 12Mbps

Compatable with USB version 1.1

USB Connectors USB-TX-DVX-2P, Type A

USB-TX-DVX-2P, Type B

RS232 and Audio

RS232 (TX-DB9Female) (RX-DB9Male)

CAT6 STP CAT6

Protocol Full duplex, transparent to all baud rate

Audio Signal Type Stero Audio

Bandwidth 15MHz.0db
Impedance 100 Ohm
Connector 3.5 mini jack,

Power 110/120V - 5VDC - 5A

Dimension (inches) 10.81” (L) x 3.38” (W) x 1.06” (H)

Weight (lbs) 2lb

User Manual

DVX-2P

PIN 1

PIN 17

© Copyright 2011 Smart-AVI, All Rights Reserved

NOTICE

The information contained in this document
is subject to change without notice. Smart-AVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and fitness for any particular purpose.

Smart-AVI will not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance or use of this material.

No part of this document may be photocopied, reproduced
or translated into another language without prior written
consent from Smart-AVI.

Please visit smartavi.com for a expanded version of this manual.

For more information, visit www.smartavi.com.

PIN 8

C 1
C 2

C 4

C 5

C 3

PIN 24

2840 N. Naomi Ave.

Burbank, California 91504

11651 Vanowen St. North Hollywood, CA 91605

Phone: [phone]

Facsimile: [phone]

#niPlangiS#niPlangiS

1-2ataDS.D.M.6T 1tceteDgulPtoH

2+2ataDS.D.M.7T 1-0ataDS.D.M.T

4-4ataDS.D.M.9Td1leihS5/0ataDS.D.M.T
5+4ataDS.D.M.0T 2-5ataDS.D.M.T
6kcolCCD1D 2+5ataDS.D.M.T
7ataDCD2Dd2leihSkcolCS.D.M.T
8cnyS.treVgolan3A 2+kcolCS.D.M.T
9-1ataDS.D.

M.4T 2-kcolCS.D.M.T
01+1ataDS.D.M.T
1d1leihS3/1ataDS.D.M.1T CdeRgolanA
21-3ataDS.D.M.2T CneerGgolanA
31+3ataDS.D.M.3T CeulBgolanA

5VDC 1.6A

PV54+ CcnySzroHgolanA

41rewo
51DN5G CdnuorGgolanA

d3leihS4/2ataDS.D.M.8T 1+0ataDS.D.M.T

SmartAVI, Inc. / Twitter: smartavi

Tel: [phone] Fax: [phone]

http://www.SmartAVI.com

Extend 2 DVI-D, RS232, Stero Audio and USB1.1 using a

Single Enclosure

m_dvx2p_101209

Connection Diagram

TRANSMITTER

RECEIVER

POWER

110V/120V

POWER

110V/120V

RS232

AUDIO

DVI (IN)

PC/MAC

Mouse/Keyboard

6 STP Cable

220ft Max

DVI (OUT)

RS232

AUDIO

Monitor

USB1.1

USB1.1
(on Front Panel)

Applications

Connecting the DVI

1. Turn off computer and monitor.

2. Connect DVI male to male cable between the

computer and the transmitter.

3. Connect monitor or projector to the DVI port

on the receiver.

4. Connect the transmitter and receiver with 4

4.

Connect a shielded Cat 6 STP cable

CAT6 STP cables.

between port 1 on the transmitter and port 1
on the receiver.

5. Repeat for 2 other ports.

Connecting the USB In/Out

1. Connect the transmitter to the host using the A-B
USB cable (included with the unit).

2. The A side of the connector would go to the com­puter host and the B side would be connected to
the transmitter.

3. Connect the receiver to the peripheral.

4. Connect the CAT6 STP Cable.

DVI

DVI

4 STP-CAT6

USB / RS232

Audio / USB / RS232

Transmitter

Audio

Receiver

• Film and Music Industry: Perfect for recording studios

and editing stations that need to be isolated.

Medical: In an environment where display

monitors and workstations cannot be

in close proximity of various pieces of

medical equipment.

Data Centers and Server Rooms:

Allows for users to access CPUs

from a remote work space.

USB

Connecting the Audio and RS232

1. Connect an RS232 cable and/or audio cable to the
souce unit.

2. Connect the Audio using 3.5mm cable at the transmitter

3. Connect the Speaker/s. at the Receiver.

4. Connect the last CAT6
STP Cable.

Preparing & Connecting System CAT5 Cable
Following is the wiring standard for terminating CAT 5
cable using RJ-45 connector:

Pair 1 Pins 1 & 2
Pair 2 Pins 3 & 6
Pair 3 Pins 4 & 5
Pair 4 Pins 7 & 8

Connectors: RJ-45
Capacitance: 14 pf/ft (46.2 pf/m)
Conductor Gauge: 24 AWG
Impedance: 100 +/- 15 ohms

4 - Pair

The receiver provides remote power up to 500

Note:

mA to the connected peripherals. This power comes
from the host computer and is passed by the transmitter
to the receiver. In some applications, and external power
supply is required. SmartAVI can provide a power supply
for such cases with the receiver and transmitter units.

Connecting the TX/RX

1. Connect DVI, USB (In/Out) and Audio/RS232 as outlined.

2. Connect Power Supply (5VDC - 5A).

3. Turn on TX and RX.