Smart Avi DVN-16Pro User Manual

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICATIONS

VIDEO

Format DVI-D Single Link

Maximum Pixel Clock 165 MHz

Input Interface (16) DVI-D 29-pin (female)

Output Interface (1) DVI-D 29-pin (female)

Resolution Up to 1920 x 1200

@60Hz

DDC 5 volts p-p(TTL)

Input Equalization Automatic

Input Cable Length Up to 20 ft.

Output Cable Length Up to 20 ft.

AUDIO

Input Interface (16) 3.5 mm Stereo Audio

Output Interface (1) 3.5 mm Stereo Audio

Impedance 600 Ohm

Frequency Response 20 Hz to 20 kHz

Nominal Level 0-1.0 V

Common Mode Rejection at 60 dB

OTHER

Power External 100-240 VAC/

Dimensions 17” W x 3.5” H x 6.75“ D

Weight 10 lbs.

Approvals UL, CE, ROHS Compliant

Operating Temp. 32-131 °F (0-55 °C)

Storage Temp. -4-185 °F (-20-85 °C)

Humidity Up to 95%

Emulation Keyboard and Mouse

5VDC4A @20W

WHAT’S IN THE BOX

PART NO. QTY DESCRIPTION

DVN-16PROS 1 DVNET-16Pro, 16x1 DVI-D, USB

2.0, Audio Switch

Power Supply 1 PS5VDC4A

User Manual 1

DVNET-16Pro

16-PORT DVI-D, USB AND

KVM SWITCH WITH KEY-

BOARD/MOUSE EMULATION

USB

Signal Type USB 2.0, 1.1, and 1.0 w/

Input Interface (16) USB Type B (female)

Output Interface (2) USB Type A (female)

CONTROL

Front Panel Tactile Switch

RS-232 Via Control @ 115200 bps

Hotkeys Via Keyboard

IR Optional

internal hub

for keyboard and mouse
emulation;
(2) for USB 2.0 Transpar­ent

Designed and Manufactured in the USA

800.AVI.2131

Tel: [phone] Fax: [phone]

11651 Vanowen St. North Hollywood, CA 91605

SmartAVI.com

Control 16 Computers (PC, Mac, or
Linux) on one Display Up To 20 Feet

Away with Keyboard/Mouse Emulation,

Stereo Audio and USB 2.0

USER MANUAL

INTRODUCTION

The DVNET-16Pro is a cross-platform switch capable
of sharing a DVI-D monitor, stereo speakers, and
USB 2.0 devices between 16 computers. It is RS-232
and infrared compliant, capable of being controlled
remotely via third-party software.

FEATURES

 Compatible with Windows, Mac and Linux Operat-

ing Systems

 Supports up to 1920x1200 digital video resolu-

tion

 Uses universal DVI single-link connectors
 Supports all USB 2.0 Devices (Flash drives, Print-

ers, Cameras, Scanners, etc.)

 Supports USB keyboard and mouse emulation
 Balanced stereo audio output
 Front panel tactile switch with LCD display for lo-

cal control

 Full IR and RS-232 control for remote control
 Special Hotkey keyboard sequence to switch inde-

pendent simultaneous device selection: Flexibility
is key to the DVNET-16Pro

DDC LEARNING

The DVN-16P is fully capable of “learning” and re-
membering what type of display monitor is con­nected to the unit. Programming the DDC (Display
Data Channel) is accomplished using the two but­tons located on the front panel.

To enter Learning Mode, simply press both the Scroll
and Enter buttons at the same time until the display

reads “Menu”. By then pressing the Scroll button,

you may cycle through the following DDC learning
modes.

Learn PC: For PC computers; display up to
1920x1200.
Learn Mac: For Mac computers; display up to
1920x1200.
Learn Screen: To learn the type of display monitor
connected to the “OUT” port.

**To select a mode, press the Enter button

INSTALLATION DIAGRAM

CONNECTING THE DVNET-16Pro

1. Ensure that power is disconnected from DVNET­16Pro.

2. Connect the DVI cables, USB cables (male-A to
male-B), and audio cables from the computers
to the respective ports on the DVNET-16Pro.

3. Optionally connect RS-232 for control functions.

4. Connect the USB keyboard and mouse on the
two USB ports on the right (close to the RS-232
port).

Note: The 2 ports on the right are dedicated for
keyboard and mouse emulation. The 2 on the
left are for other USB peripherals (flash drives,
printers, etc.)

5. Connect the speakers into the Audio Out port
located above the USB ports.

6. Connect the display monitor the OUT DVI con­nector on the DVNET-16Pro.

7.

Power on the DVNET-16Pro.

COMMANDS HOTKEYS RS-232 CONTROL

Switch all devices (KVM, USB 2.0, and Audio) [CTRL], [CTRL], m, [port #], [ENTER] ‘//m[port #][ENTER]’

Switch KVM only [CTRL], [CTRL], c, [port #], [ENTER] ‘//c[port #][ENTER]’

Switch audio only [CTRL], [CTRL], a, [port #], [ENTER] ‘//a[port #][ENTER]’

Reset DVNET-16Pro [CTRL], [CTRL], r, [ENTER] ‘//r[ENTER]’

CONTROLLING THE DVNET-16Pro

Front Panel Control

To switch ports using the front panel, press either
the Enter button to navigate up and Scroll button
for down. DDC learning is also done through the

front panel buttons.

RS-232 Control

To switch ports using an RS-232 connection, use a
male-to-female serial cable to connect a computer
to the RS-232 port of the DVNET-16Pro. Use termi­nal client software such as the HyperTerminal to
connect to the DVNET-16Pro. Make sure to use the
standard communication mode of 115200 bps, 8,
N, 1.

Hotkey Commands

The Hotkey command is a keyboard sequence
used to trigger an action on the DVNET-16Pro
through the use of the keyboard connected on the
USB port of the DVNET-16Pro. To activate the hot­key sequence, press the CTRL key twice and then

enter the desired hotkey commands.