Page 1
SMARTBoard® M600i6
interactive whiteboard systems
CONFIGURATION AND USER’S GUIDE
FOR MODELS M680i6 AND M685i6
Page 2
FCC warn in g
This equip ment has be en tested and found to compl y wi th the limits for a Class A dig ital de vice , p ursuantto Part 15 of the FCC Rules . These limits are desi gned to
pro vide reasonable prote ction against harmful interfer ence when the equipment i s o pe rated in a commercial environment. T his e quipment g enerates , use s and
can radi ate rad io freque ncy ener gy and, if not installed and used in accor dance w ith the manufacture r’s instructions, may cause harmful inter ference to radio
communications. Operation of this equipment i n a r esi dential area i s l ikely to cause harmful i nterfere nce i n which case the user will be re quired to cor rec t the
interfere nce at his o wn e xpense .
Trad emark n ot ice
SMARTBoard , S MARTNoteb ook, SMARTMeetingPr o, DViT, smarttech, the SMART log o and all SMART tagli nes are trademarks or regi stere d trademarks of
SMARTTe chnolo gie sULC in the U .S. and/or o ther countrie s. Micro soft, Windows and InternetEx plor er are either regis tere d trademarks o r trademarks of
Microso ft Corp oration in the U .S. and/or other co untrie s. All o ther third-party pro duct and company names may be trademarks of their respe ctive owners .
Copyri ght not ice
© 20 13–2015 SMARTTe chnologi esUL C. All rights rese rve d. No part o f this publication may b e rep rod uced, transmitted, transcrib ed, stor ed in a retrie val system
or translated into any language in any for m by any means withoutthe prio r written co nsent of SMARTTec hnolo gie sULC. Information i n this manual is subject to
change without notice and d oe s not repr ese nt a co mmitment on the part o f SMART.
This pro duct and/or use there of cover ed by one or more of the follow ing U .S. patents: s marttech.com/patents.
01/2015
smar ttech.com/kb/170549
Page 3
Important information
Before you install and use your SMARTBoard interactive whiteboard system, read and understand
the safety warnings and precautions in this user’s guide and the included important information
document. These safety warnings and precautions describe the safe and correct operation of your
interactive whiteboard system and its accessories, helping you to prevent injuries and equipment
damage. Ensure that your interactive whiteboard system is always being used correctly.
In this document, “interactive whiteboard system” refers to the following:
l SMARTBoard M685 series interactive whiteboard
l SMARTUF70 or SMARTUF70w projector
l Accessories and optional equipment
The projector included with your system is designed to work only with certain SMARTBoard
interactive whiteboard models. Contact your authorized SMART reseller (smarttech.com/where) for
more information.
Safety warnings, cautions and important information
Installation
WARNI NG
l Failure to follow the installation instructions shipped with your SMART product could result in
personal injury and damage to the product.
l To reduce the risk of fire or electric shock, do not expose the SMART product to rain or
moisture.
l Two people are required to mount your SMART product because it may be too heavy for
one person to safely maneuver.
When you lift your interactive whiteboard, you and your assistant should stand on either side
of the screen, supporting its weight at the bottom while balancing the top with your other
hands.
i smar ttech.com/kb/170549
Page 4
IMP ORTANT INFORMATION
l When mounting the projector boom on a framed or hollow wall, attach the mounting bracket
to a stud to safely support the projector’s weight. If you use only drywall anchors, the drywall
can fail, resulting in possible personal injury, and damage to the product which may not be
covered by your warranty.
l Do not leave cables on the floor where they can be a tripping hazard. If you must run a cable
over the floor, lay it in a flat, straight line and secure it to the floor with tape or a cable
management strip of a contrasting color. Handle cables carefully and avoid excessive
bending.
CAUTION
l Do not operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture can condense on the
lens and crucial internal parts. Allow the system to stabilize to room temperature before
operation to prevent possible damage to the unit.
l Do not place the unit in hot locations, such as near heating equipment. Doing so could cause
a malfunction and shorten the life of the projector.
l Avoid setting up and using the SMART product in an area with excessive levels of dust,
humidity and smoke.
l Do not place your SMART product in direct sunlight or near any appliance that generates a
strong magnetic field.
l You must connect the USB cable that came with your SMARTBoard interactive whiteboard
to a computer that has a USB compliant interface and that bears the USB logo. In addition,
the USB source computer must be compliant with CSA/UL/EN 60950 and bear the CE mark
and CSA and/or UL Mark(s) for CSA/UL 60950. This is for operating safety and to avoid
damage to the SMARTBoard interactive whiteboard.
IMPORTANT
l Make sure an electrical socket is near your SMART product and remains easily accessible
during use.
l Using your SMART product near a TV or radio could cause interference to the images or
sound. If this happens, move the TV or radio away from the projector.
ii smar ttech.com/kb/170549
Page 5
IMP ORTANT INFORMATION
Operation
WARNI NG
l If you are using an external audio system, use only the power supply included with that
product. Using the wrong power supply might create a safety hazard or damage the
equipment. If in doubt, refer to the specification sheet for your product to verify the power
supply type.
l Do not climb (or allow children to climb) on a wall- or stand-mounted SMARTBoard
interactive whiteboard.
Do not climb on, hang from or suspend objects from the projector boom.
Climbing on the interactive whiteboard or projector boom could result in
personal injury or product damage.
CAUTION
l Do not block the projector’s ventilation slots and openings.
IMPORTANT
l Keep your remote control in a safe place because there is no other way to access menu
options.
l Disconnect the product from its power source when it’s not used for a long period.
Other precautions
If you own a SMARTproduct other than a SMARTBoard interactive whiteboard system, refer to the
installation manual for your product for relevant warnings and maintenance instructions.
Environmental requirements
Before you install your SMARTBoard interactive whiteboard system, review the following
environmental requirements.
Environmental
requirement
Parameter
Operating temperature
Storage temperature
iii smar ttech.com/kb/170549
41°F to 95°F (5°C to 35°C) from 0' to 6000' (0 m to 1800 m)
l
41°F to 86°F (5°C to 30°C) from 6000' to 9800' (1800 m to 3000 m)
l
-4°F to 122°F (-20°C to 50°C)
l
Page 6
IMP ORTANT INFORMATION
Environmental
requirement
Humidity
Water and fluid
resistance
Dust
Electrostatic discharge
(ESD)
Cables
Parameter
5% to 95% storage relative humidity, non-condensing
l
5% to 85% operating relative humidity, non-condensing
Intended for indoor use only. Doesn’t meet any salt-spray or water
l
ingress requirements.
Don’t pour or spray liquids directly onto your interactive whiteboard,
l
the projector or any of its sub-components.
Intended for use in office and classroom environments. Not for
l
industrial use where heavy dust and pollutants can cause
malfunctions or impaired operation. Periodic cleaning is required in
areas with heavier dust. See
Cleaning the projector
on page24 for
information on cleaning the projector.
EN61000-4-2 severity level 4 for direct and indirect ESD
l
No malfunction or damage up to 8kV (both polarities) with a
l
330ohm, 150 pF probe (air discharge)
Unmated connectors meet no malfunction or damage up to 4kV
l
(both polarities) for direct (contact) discharge
All SMARTBoard interactive whiteboard system cables should be
l
shielded to prevent potential accidents and degraded video and
audio quality.
Conducted and
radiated emissions
EN55022/CISPR 22, Class A
l
iv smarttech.com/kb/170549
Page 7
Contents
Important in format ion i
Safety warnings, cautions and important information i
Environmental requirements iii
Chapter 1: Abou t your interact ive whit eboard syst em 1
SMARTBoard interactive whiteboard system features 2
Included accessories 4
Chapter 2: I nstalling your in teract ive whit eboard system 5
Choosing a location 5
Choosing a height 6
Securing the projector to the boom 6
Routing the cables 6
Installing SMART software 7
Chapter 3: Using your interact ive whiteboard syst em 9
Using your projector 9
Using your interactive whiteboard 21
Chapter 4: Maint aining your interactive whiteboard syst em 23
Maintaining your interactive whiteboard 23
Cleaning the projector 24
Focusing and adjusting the projector image 25
Replacing the projector lamp 26
Chapter 5: Trou bleshooting your interactive whiteboard syst em 31
Before you start 32
Determining you interactive whiteboard system’s status 33
Resolving interactive whiteboard issues 34
Resolving projector issues 35
Accessing the service menu 42
Transporting your interactive whiteboard system 43
Appendix A: R emotely managing your system t hrough a network interface 45
Web page management 45
Simple Network Management Protocol (SNMP) 52
Appendix B: Remot ely managing your system through an RS-232 serial interface 53
Serial interface settings 54
Projector programming commands 55
v smarttech.com/kb/170549
Page 8
CONTENTS
Appendix C: Int egrating other devices 77
Video format 77
Connecting peripheral sources and outputs 83
Appendix D: Remote cont rol code definitions 85
Appendix E: Hardware environ ment al compliance 87
Waste Electrical and Electronic Equipment and Battery regulations (WEEE and
BatteryDirectives) 87
Batteries 87
Mercury 87
More information 87
Index 89
vi smarttech.com/kb/170549
Page 9
Chapter 1
system
SMARTBoard interactive whiteboard system features 2
SMARTBoard M600 series interactive whiteboard 2
SMARTUF70 or SMARTUF70w projector 3
Included accessories 4
Remote control 4
Pens 4
Optional accessories 4
Your SMARTBoard interactive whiteboard system combines the following components:
l SMARTBoard M600 series interactive whiteboard
l Wall-mounted, short-throw SMARTUF70 or SMARTUF70w projector
l Accessories and optional equipment
This chapter describes the features of your interactive whiteboard and provides information about
product parts and accessories.
1 smar ttech.com/kb/170549
Page 10
CHAPTER 1
ABOUT YOUR INTERACTIVE W HITEBOARD SYSTEM
SMARTBoard interactive whiteboard system
features
Your SMARTBoard interactive whiteboard system
uses the short-throw, high-offset SMARTUF70 or
SMARTUF70w projector. The throw distance of the
SMARTUF70 and SMARTUF70w projectors is half
that of the SMARTUF65 projector, resulting in a
shorter boom and reduced shadows on the
projected image.
When the projector displays an image from your
computer on the touch-sensitive interactive
whiteboard, you can do everything that you can do at
your computer—open and close applications, scroll
through files, conference with others, create new
documents or edit existing ones, visit websites, play
video clips and more—by touching the screen. You
can use an array of gestures within applications.
This projector also supports video and audio connections from a variety of devices, including
DVD/Blu-ray™ players, VCRs, document cameras and digital cameras, and can project media from
these sources onto the interactive screen.
When you use SMART software with your SMARTBoard interactive whiteboard system, you can
write or draw over the projected computer image in digital ink using a pen tray pen or your finger,
and then save these notes to a .notebook file or directly into any Ink Aware application.
SMARTBoard M600 series interactive whiteboard
Your SMARTBoard M600 series interactive whiteboard, featuring SMART’s proprietary DViT®
(DigitalVisionTouch) technology, is the most intuitive touch-sensitive front projection interactive
whiteboard in the world.
2 smar ttech.com/kb/170549
Page 11
CHAPTER 1
ABOUT YOUR INTERACTIVE W HITEBOARD SYSTEM
Other features of your interactive whiteboard include
the following:
l Pen tray buttons that activate the pens’ colors
and the on-screen keyboard, as well as right-
click and Orientation functions
l A durable hard-coated surface that is optimized
for projection and is easily cleaned
For more information about your SMARTBoard
interactive whiteboard, see the
SMARTBoard M600
series interactive whiteboard user’s guide
(smarttech.com/kb/170410).
SMARTUF70 or SMARTUF70w projector
The SMARTUF70 or SMARTUF70w projector system includes a
short-throw projector for use with SMARTBoard interactive
whiteboards and a sturdy support system suitable for many different
environments.
Other features of your projector system include the following:
l A wall-mounted, high-offset projector engine that uses DLP® technology by
TexasInstruments™, providing BrilliantColor™ performance and Gamma 2.2 correction with
SMART Presentation, Bright Room, Dark Room, sRGB and User modes
l PAL, PAL-N, PAL-M, SECAM, NTSC and NTSC 4.43 video system compatibility
l HDMI, Composite,and VESA® RGB video inputs (not included)
l WXGA, QVGA, VGA, SVGA, XGA, SXGA, SXGA+ and UXGA video format compatibility
l Native 1024 × 768 resolution (SMARTUF70 projector)
OR
Native 1280 × 800 resolution (SMARTUF70w projector in 16:10 aspect ratio mode)
l Remote management via a serial RS-232 interface, web page or SNMP
l An alert broadcast feature that enables administrators to send notification messages to
network-connected projector systems for immediate on-screen display
l Protected cable routing through a cable cover that limits tampering and clutter
3 smarttech.com/kb/170549
Page 12
CHAPTER 1
ABOUT YOUR INTERACTIVE W HITEBOARD SYSTEM
l A secure mounting and installation system that includes the following:
o
An optional projector padlock ring to prevent removal of the projector from the boom
o
Accessory mounting hardware for solid masonry or framed wall installations kit (Part
Number 1007416)
o
Templates and instructions for positioning the system safely
Included accessories
The following accessories are included with your interactive whiteboard system.
Remote control
The remote control enables you to control the system and set up your projector. Use
the remote control to access menu options, system information and input selection
options.
Pens
There are two pens included with your interactive whiteboard.
Pick up a pen and press one of the four color buttons on the
pen tray (black, red, green or blue) to select the color of digital
ink you write on the interactive whiteboard.
Optional accessories
You can add a variety of accessories to your interactive whiteboard to best meet your specific
needs. Purchase these items from your authorized SMART reseller (smarttech.com/where).
For more information on accessories, go to smarttech.com/accessories.
4 smarttech.com/kb/170549
Page 13
Chapter 2
whiteboard system
Choosing a location 5
Choosing a height 6
Securing the projector to the boom 6
Routing the cables 6
Installing SMART software 7
IMPORTANT
Use the
(smarttech.com/kb/170555) to install your interactive whiteboard and projector.
This chapter provides additional considerations and details for installing your interactive
whiteboard system.
SMARTBoard M600i6 interactive whiteboard system installation guide
Choosing a location
Choose a location for your interactive whiteboard system that’s far from bright light sources, such
as windows and strong overhead lighting. IR lighting can cause issues with the performance of the
cameras and can lead to unintentional or missed touches.
Select a wall with a flat, regular surface and sufficient clearance to accommodate your interactive
whiteboard system. Install the projector and your interactive whiteboard on the same flat surface.
For best presentation alignment, mount your interactive whiteboard system in a location that’s
central to your audience’s viewing direction.
For mobile or adjustable installation options, contact your authorized SMART reseller.
WARNI NG
5 smar ttech.com/kb/170549
Page 14
CHAPTER 2
INSTALLI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
Refer to your interactive whiteboard system’s specifications (available at smarttech.com/support)
for its weight. Check your local building codes to ensure that your wall can support this weight,
and use appropriate mounting hardware for your wall type.
Choosing a height
SMART includes a mounting template with each interactive whiteboard system. If you lose this
template, contact your authorized SMART reseller. Using this template ensures that you can do the
following:
l Mount the projector at a safe height for head space clearance, while maintaining enough
space for airflow and installation access above the unit.
l Position the projector at the correct height above your interactive whiteboard to align the
projected image with the touch screen.
Dimensions on the template recommend a distance from the floor suitable for adults of average
height. You should consider the general height of your user community when you choose a
location for your interactive whiteboard.
Securing the projector to the boom
To learn how to secure the SMARTUF70 or SMARTUF70w projector to the boom, see the
included
(smarttech.com/kb/170555).
SMARTBoard M600i6 interactive whiteboard system installation guide
Routing the cables
If your interactive whiteboard uses one mounting bracket, make sure that all projector cables pass
along the top of the bracket and then down the side of the interactive whiteboard.
If your interactive whiteboard uses two mounting brackets, make sure that all projector cables pass
between the brackets. Space your wall-mounting brackets 4" (10.2 cm) apart to provide full support
for the weight of your interactive whiteboard.
6 smar ttech.com/kb/170549
Page 15
CHAPTER 2
INSTALLI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
IMPORTANT
Do not connect the power cable to a power outlet until you have connected all the cables to the
projector and interactive whiteboard.
Installing SMART software
You must install SMARTsoftware, such as SMARTNotebook® collaborative learning software on
the computer connected to your interactive whiteboard system to access all of its features.
Download SMARTsoftware from smarttech.com/software. These web pages list the minimum
hardware requirements for each software version. If SMART software is already installed on your
computer, take this opportunity to upgrade your software to ensure compatibility.
7 sm arttech.com/kb/170549
Page 16
Page 17
Chapter 3
system
Using your projector 9
Using your remote control 9
Replacing the remote control battery 10
Using the remote control buttons 11
Adjusting projector settings 12
Focusing the image 18
Adjusting the image 19
Projector connection diagram 19
Using your interactive whiteboard 21
This chapter describes the basic operation of your interactive whiteboard system and explains
how to set up your remote control, retrieve system information, access the projector’s image
adjustment options and integrate your interactive whiteboard system with peripheral devices.
Using your projector
This section explains how to use your projector and its included remote control.
Using your remote control
The projector remote control enables you to access on-screen projector menus and change
projector settings.
9 smar ttech.com/kb/170549
Page 18
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Replacing the remote control bat tery
Follow this procedure to replace the remote control battery.
WARNI NG
l Reduce the risk associated with a leaking battery in the projector’s remote control by
following these practices:
o
Use only the specified CR2025 coin-cell battery.
o
Remove the battery when the remote control is unused for an extended period.
o
Do not heat, disassemble, short or recharge the battery, or expose it to fire or high
temperatures.
o
Avoid eye and skin contact with the battery if it has a leak.
l Dispose of the exhausted battery and product components in accordance with applicable
regulations.
To replace t he remot e cont rol batt ery
1. Hold down the side release on the leftside of the battery holder and pull the battery holder
completely out of the remote control.
2. Remove the old battery from the battery holder and replace it with a CR2025 coin-cell
battery.
IMPORTANT
Align the battery’s positive (+) and negative (–) terminals with the correct signs on the
battery holder.
3. Insert the battery holder into the remote control.
10 smar ttech.com/kb/170549
Page 19
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Using t he remot e cont rol bu ttons
The projector remote control enables you to access on-screen menus and change projector
settings. Use the Power button on the remote control to put the projector into Standby mode or
to turn it on. You can also use the Inpu t button on the remote control to switch sources on the
projector.
Number Funct ion Description
1 Input Select a video and audio input source on the
projector and the associated USB input source on
the ECP, if present.
2 Menu Show or hide the projector menus.
3 (Left), (Right),
Change the menu selections and adjustments.
(Up) and (Down) arrows
4 Hide Freeze, hide or display the image:
Press once to freeze the image.
l
For example, you can display a question on
the screen while you check your e-mail.
Press again to hide the image, that is, to
l
display a black screen.
Press again to return to the live image.
l
5 Mode Select a display mode.
6 Mute Mute audio amplification.
7
(Power)
Turn on the projector or put it into Standby mode.
8 (Enter) Accept the selected mode or option.
9 (Volume Up) Increase audio amplification volume.
10 (Volume Down) Decrease audio amplification volume.
11 smar ttech.com/kb/170549
Page 20
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
NOTE
The Mut e, Volume Up and Volume Down buttons work only if there is an audio source
connected to the projector for the selected video input source.
For information on using the remote control’s Menu button to adjust the projector settings, see
Adjusting projector settings.
Adjusting projector sett ings
The remote control’s Menu button enables you to access the on-screen display to adjust the
projector settings.
IMPORTANT
Keep your remote control in a safe place because there is no other way to access menu options.
Sett ing Use Notes
Image Adjustment menu
Display Mode Indicates the projector’s
display output
(SMARTPresentation,
BrightRoom, DarkRoom,
sRGB and User).
Brightness Adjusts projector brightness
from 0 to 100.
Contrast Adjusts the difference
between the lightest and
darkest parts
of the image from 0 to 100.
Frequency Adjusts the display data
frequency of the projected
image from -5 to 5 to match the
frequency of your computer’s
graphics card.
Tracking Synchronizes your projector’s
display timing with your
computer’s graphics card from
0 to 63.
The default is SMARTPresentation.
The default is 50.
The default is 50.
The default is 0.
This setting applies to VGA inputs only.
This setting applies to VGA inputs only.
12 smarttech.com/kb/170549
Page 21
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
H-Position Moves the horizontal position
of the source video left or right
from 0 to 100 (relative to the
projected image).
V-Position Moves the vertical position of
the source video up or down
from -5 to 5 (relative to the
projected image).
White Peaking Adjusts the image color
brightness from 0 to 10 while
providing more vibrant white
shades.
Degamma Adjusts the color performance
of the display from 1 to 3.
Color Adjusts the Red, Green, Blue,
Cyan, Magenta and Yellow
colors on the projector from 0
to 100 to provide custom color
and luminance output.
Don’t adjust this setting unless you’re advised
to by SMARTSupport.
Apply this setting only after you make all
boom adjustments.
This setting applies to VGA inputs only and is
useful in situations where the source video is
cut off.
Don’t adjust this setting unless you’re advised
to by SMARTSupport.
Apply this setting only after you make all
boom adjustments.
This setting applies to VGA inputs only and is
useful in situations where the source video is
cut off.
A value closer to 0 creates a natural image
and a value closer to 10 enhances brightness.
The default is 10.
The default is 2.
Each color has a default value of 100.
Adjustments to the color settings register
under the User mode.
Audio menu
Volume Adjusts the projector’s volume
amplification from -20 to 20.
Mute Mutes the projector’s audio
output.
Disable Volume
Control
Line out
Disables the projector’s
volume control.
Enables or disables the line
out.
13 smarttech.com/kb/170549
The default is 0.
The default is off.
If you mute the projector’s audio output and
then increase or decrease the volume, the
volume is restored automatically. You can
prevent this from happening by disabling the
volume control.
The default is on
Page 22
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
Microphone Enables or disables the
microphone
Speaker Enables or disables the
speaker
Projector Functions menu
Auto Signal
Detect
Enables or disables signal
searching of input connectors.
Lamp Reminder Turns the lamp replacement
reminder on or off.
Lamp Mode Adjusts lamp brightness to
Standard or Economy.
Auto Power Off
(minutes)
Sets the length of the auto
power-off countdown timer
between 1 and 240 minutes.
The default is on
The default is on
The default is off.
Select On to have the projector continuously
switch inputs until it finds an active video
source.
Select Off to maintain signal detection in one
input.
This reminder appears 100 hours before the
recommended lamp replacement.
Standard displays a high-quality, bright
image.
Economy increases the lamp life by
decreasing the brightness of the image.
The default is 120 minutes.
The timer begins to count down when the
projector no longer receives a video signal.
The timer finishes when the projector enters
Standby mode.
Select 0 to turn off the timer.
Zoom Adjusts the zoom to the center
of the image in or out from 0 to
30.
Keystone Adjusts the size of the top and
bottom edge
Projector ID Displays the projector’s unique
ID number (from 0 to 99) within
your organization’s network.
14 smarttech.com/kb/170549
The default is 0.
Zooming in cuts off the outer edges of the
source video.
Ensure that the top and bottom edges of the
image are horizontal before you position the
left and right edges of the image relative to
your interactive whiteboard.
You can refer to or change this number when
using the network remote management
feature (see
system through a network interface
Remotely managing your
on
page45).
Page 23
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
Aspect Ratio Adjusts the image output to
FillScreen, MatchInput or
16:9.
Startup Screen Selects the type of startup
screen (SMART, Capt ure User
Start up Screen, Preview
Start up Screen), or Image
Alignment Screen.
The default is FillScreen.
FillScreen produces an image that fills the
entire screen by stretching and scaling the
source video to match the projector’s native
resolution and aspect ratio.
MatchInput displays the source video in its
native resolution and aspect ratio. As a result,
unused space could appear along the top
and bottom edges of the screen (letterbox
format) or along the left and right edges of
the screen (pillarbox format).
See
Video format
on page77 for
descriptions of each mode.
This screen displays when the projector lamp
is starting and a video source signal isn’t
displayed.
SMAR T displays the default SMART logo on
a blue background.
Capture User Start up Screen closes the onscreen display menu and captures the entire
projected image. The captured image is
displayed the next time the on-screen display
opens. (The capture can take up to one
minute, depending on the complexity of the
background graphic.)
Preview Startup Screen enables you to
preview the default or captured startup
screen.
Image Alignment Screen enables you to
adjust the projected image size, shape and
location.
Image
Alignment
Screen
Enables you to adjust the
projected image size, shape
and location.
Network menu
Network and
VGAOut
Activates the projector’s RJ45
(8P8C) connector and network
features.
15 smarttech.com/kb/170549
The image alignment screen appears the first
time you start your projector. However, you
can access it from the startup screen menu
any time. Press Menuor Enter to close it.
Page 24
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
Status Displays the current network
status (Connected,
Disconnected or Off).
DHCP Displays the status of the
network’s Dynamic Host
Configuration Protocol (DHCP)
as On or Off.
Password
Reminder
E-mails the network password
to the predefined e-mail
recipient.
IP Address Displays the projector’s current
IP address in values between
0.0.0.0 and 255.255.255.255.
Subnet Mask Displays the projector’s subnet
mask number in values
between 0.0.0.0 and
255.255.255.255.
The default is off.
The default is on.
On enables a DHCP server on the network to
automatically assign an IP address to the
projector.
Off enables an administrator to assign an IP
address manually.
See
Web pa ge management
on page45 to
set up a destination e-mail address.
To change the projector’s IP address, use the
RS-232 connector or use a DHCP server to
assign a dynamic IP address, and then set a
static IP address using the network remote
management feature (see
Remotely
managing your system through a network
interface
on page45).
Gateway Displays the projector’s default
network gateway in values
between 0.0.0.0 and
255.255.255.255.
DNS Displays the projector’s primary
domain name server (DNS) IP
address in values between
0.0.0.0 and 255.255.255.255.
MAC Address Displays the projector’s MAC
address in xx-xx-xx-xx-xx-xx
format.
Group Name Displays the projector’s
workgroup name as set by an
administrator (maximum 12
characters).
You can set the projector’s workgroup name
using the remote management features (see
Remotely managing your system through a
network interface
on page45 and
Remotely
managing your system through a n RS-232
serial interface
on page53).
16 smarttech.com/kb/170549
Page 25
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
Projector Name Displays the projector’s name
as set by an administrator
(maximum 12 characters).
You can set the projector’s name using the
remote management features (see
Remotely
managing your system through a network
interface
on page45 and
Remotely
managing your system through a n RS-232
Location Displays the projector’s
location as set by an
administrator (maximum 16
characters).
serial interface
You can set the projector’s location using the
remote management features (see
managing your system through a network
interface
on page53).
on page45 and
Remotely
Remotely
managing your system through a n RS-232
Contact Displays the contact name or
number for projector support
as set by an administrator
(maximum 16 characters).
serial interface
You can set the contact name or number
using the remote management features (see
Remotely managing your system through a
network interface
on page53).
on page45 and
Remotely
managing your system through a n RS-232
serial interface
on page53).
Language menu
Language Selects language preference. Projector menu support is available in English
(default), Chinese (Simplified), Chinese
(Traditional), Czech, Danish, Dutch, Finnish,
French, German, Greek, Italian, Japanese,
Korean, Norwegian, Polish, Portuguese
(Brazil), Portuguese (Portugal), Russian,
Spanish and Swedish.
Informat ion menu
Lamp Hours Displays the current number of
lamp usage hours from 0 to
4000 hours from when it was
last reset.
Input Displays the currently
displayed video input source
(VGA-1, VGA-2, HDMI or None).
Resolution Displays the projector’s most
recently detected video
source signal resolution and
refresh rate.
17 smar ttech.com/kb/170549
Always reset the lamp hours after you
replace a lamp, because lamp service
reminders are based on the current hours of
use. See
Resetting the la mp hours
on
page29 for details on the lamp hours reset
procedure.
If there is no current video input source
signal, this setting displays the last known
source signal image resolution and refresh
rate.
Page 26
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Sett ing Use Notes
Firmware
Version
Displays the projector’s digital
display processor (DDP)
firmware version in x.x.x.x
format.
MPU Version Displays the projector
microprocessor unit (MPU)
firmware version in x.x.x.x
format.
Network Version Displays the projector’s
network communications
processor firmware version in
x.x.x.x format.
If you haven’t enabled the Network and VGA
Out setting, this setting is unable to display
the projector’s network communications
processor firmware version and displays
0.0.0.0 instead.
Model Number Displays the projector’s model
number.
Serial Number Displays the projector’s serial
number.
Focusing the image
Use the focus lever located on the projector lens to focus the projected image.
To focus t he image
Rotate the focus ring clockwise or counter clockwise until the image is in focus.
18 smarttech.com/kb/170549
Page 27
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
Adjusting the image
Refer to these notes when adjusting the projected image, as described in the included
SMARTBoard M600i6 interactive whiteboard system installation guide
(smarttech.com/kb/170555).
l While adjusting the projected image size, shape and location, use the projector’s default
background so that you can see the full projected image clearly. Don’t use other images,
which might be cropped or scaled by the projector and could result in a misleading projected
image size, shape and location.
l Use the mechanical adjustments described in the installation document to make all physical
image adjustments. Don’t use the projector’s on-screen menu options during the projector
alignment process.
l Be aware that as you tilt the projector up or lower its mounting boom to raise the image, the
entire projected image increases or decreases in size, especially at the bottom of the
projected image.
l When adjusting keystone (tilt), ensure that the top and bottom edges of the image are
horizontal before you position the left and right edges of the image relative to your interactive
whiteboard.
l When you move the projector forward or backward on the boom to make the image larger or
smaller, you might need to tilt or turn the projector slightly to keep the image square. Loosen
the lever slightly to aid in this adjustment.
l To fine-tune the image, you might need to repeat all steps described in the installation
document in smaller increments.
Projector connection diagram
You can connect a variety of peripheral devices to your projector, including DVD/Blu-ray players,
VCRs, document cameras, digital cameras and high-definition sources, as well as peripheral device
outputs, such as a secondary projector or a flat-panel display and powered speakers.
NOTE
You might need to purchase third-party adapters to connect certain peripheral devices.
19 smarttech.com/kb/170549
Page 28
CHAPTER 3
1
3
4
5 6 10
7
2
8 9 11 12 13 14
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
No. Connector Connect t o:
1 Power Mains power supply
2 7-pin mini-DIN [Not used]
3 4-pin power mini-DIN 5V/2A output [Not used]
4 HDMI input High-definition video and audio source
(not included)
5 DB15F (DE-15F) RGB video input (VGA 1) Primary computer (not included)
6 DB15F (DE-15F) RGB video output (VGA
Secondary display (not included)
Out)
7 RCA Composite video input
8 3.5 mm phone jack audio input (×2) Audio sources associated with primary
and secondary computers
9 Left and right RCA audio input
Audio source (not included)
10 3.5 mm phone jack audio output Speakers (not included)
11 3.5 mm phone jack microphone Microphone (not included)
12 RJ45 (8P8C) Network (for web page management and
SNMP access)
13 DB9F (DE-9F) RS-232
14 USB B Computer (for service access only)
20 smarttech.com/kb/170549
Page 29
CHAPTER 3
USING YOUR INTER ACTIVE WHITEBOARD SYSTEM
NOTES
l To connect your interactive whiteboard, see the
whiteboard system installa tion guide
l To connect accessories to your interactive whiteboard, refer to the documents included
(smarttech.com/kb/170555).
SMARTBoard M600i6 interactive
with the accessories and consult the SMARTSupport website (smarttech.com/support) for
additional information.
Using your interactive whiteboard
Refer to the
(smarttech.com/kb/170410) for in-depth information on using your interactive whiteboard and its
features.
When you connect your SMARTBoard interactive whiteboard to a computer with SMART software,
you can access the full capabilities of your interactive whiteboard.
For additional resources, go to smarttech.com, click the flag icon in the top-right corner, and then
select your country and language. In the Support section of this website, you’ll find up-to-date,
product-specific information, including setup instructions and specifications.
SMARTBoard M600 series interactive whiteboa rd user’s guide
The SMARTtraining website (smarttech.com/training) includes an extensive library of training
resources you can refer to when first learning to set up or use your interactive whiteboard system.
21 smarttech.com/kb/170549
Page 30
Page 31
Chapter 4
whiteboard system
Maintaining your interactive whiteboard 23
Preventing damage to your interactive whiteboard 23
Keeping the writing surface clean 24
Cleaning the projector 24
Focusing and adjusting the projector image 25
Replacing the projector lamp 26
Removing and replacing the projector lamp module 26
Resetting the lamp hours 29
This chapter includes methods for properly cleaning and preventing damage to your
SMARTBoard interactive whiteboard system.
Maintaining your interactive whiteboard
For information on maintaining your interactive whiteboard, see the
interactive whiteboard installation guide
With proper care, your SMARTBoard interactive whiteboard will provide years of trouble-free
service.
(smarttech.com/kb/170555).
Preventing damage to your interactive whiteboard
Although the surface of your interactive whiteboard is very durable, take the following precautions
to prevent damage.
l Don’t use sharp or pointed objects, such as ballpoint pens or pointers, as writing tools.
l Replace the pen nib when the nib wears out.
l Don’t use low-odor dry-erase markers because they can be very difficult to erase. Use
standard (high-odor) dry-erase markers that show a warning to use them only in well-ventilated
areas.
l Don’t use adhesive tape on the interactive surface.
SMARTBoard M600
23 sma rttech.com/kb/170549
Page 32
CHAPTER 4
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
l Don’t use abrasive erasers or harsh chemicals to clean your product.
l The digital cameras located in the corners of the frame are protected from dust and dirt by
windows. In extremely dusty environments, spray a household, alcohol-free glass cleaner,
such as Windex® cleaner, on a cotton swab and rub it gently on the windows. Don’t use
compressed air to clean the cameras.
Keeping the writing surface clean
Follow these tips to keep the interactive whiteboard’s surface clean.
l Clean your interactive whiteboard at least every six months.
l Don’t spray cleaner directly onto the interactive whiteboard’s surface. Instead, spray a light
amount of cleaner on a cloth and then gently wipe the interactive surface.
l
IMPORTANT
Turn off your interactive whiteboard system before you clean it so that you do not scramble
the desktop icons or inadvertently activate applications when you wipe the interactive
surface.
TIP
To view dirt or streaks more easily, set your projector to Standby (lamp off) mode.
Cleaning the projector
WARNI NG
Cleaning a wall-mounted projector can result in a fall or injury. Use caution when climbing a
ladder, and consider removing the projector from its wall-mounting bracket to clean it.
CAUTION
l Never touch the mirror with your hands or a brush, and do not scrub the surface of the mirror
with the supplied cleaning cloth. Instead, use the supplied cleaning cloth to clean the mirror
with a light touch, and do not put any cleaning solvents on the cloth or the mirror. Do not
apply pressure to the projector lens or mirror.
Before you clean the projector, press the Power button twice on the remote control to
l
put the system in Standby mode, and then allow the lamp to cool for at least 30 minutes.
24 sma rttech.com/kb/170549
Page 33
CHAPTER 4
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
l Do not spray cleaners, solvents or compressed air directly on the projector. Do not use
spray cleaners or solvents near any part of the projector because they can damage or stain
the unit. Spraying the system could spread a chemical mist on some of the projector’s
components and lamp, resulting in damage and poor image quality.
l Do not allow liquids or commercial solvents of any kind to flow into the projector base or
head.
IMPORTANT
l When cleaning the interactive whiteboard system:
o
Wipe the exterior of the projector with a lint-free cloth.
o
If necessary, use a soft cloth moistened with a mild detergent to clean the projector
housing.
l Do not use abrasive cleaners, waxes or solvents.
When cleaning the projector’s mirror:
l Use a bellows bulb or air blower bulb (commonly found in audio-visual supply stores) to blow
off dust. Never touch the mirror with your bare hands or a brush.
l If wiping the mirror is unavoidable, wear protective gloves and gather the cleaning cloth into a
ball. Gently run the cleaning cloth across the mirror like you would a feather duster. Don’t
apply any pressure to the lens or mirror.
When cleaning the projector’s lens:
l Use a bellows bulb or air blower bulb (commonly found in audio-visual supply stores) to blow
off dust. Never touch the lens with your bare hands or a brush.
l If wiping the lens is unavoidable, wear protective gloves and gather the cleaning cloth into a
ball. Gently run the cleaning cloth across the lens from the center to the edge, using the
cleaning cloth like you would a feather duster. Don’t apply any pressure to the lens or mirror.
Focusing and adjusting the projector image
For information on focusing and adjusting the projector image, see
and
Adjusting the image
on page19.
Focusing the image
on page18
25 smar ttech.com/kb/170549
Page 34
CHAPTER 4
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
Replacing the projector lamp
This section provides instructions for replacing the projector lamp module.
Removing and replacing the projector lamp module
Eventually the lamp will dim and a message will appear reminding you to replace it. Make sure you
have a replacement lamp module before proceeding with the following instructions.
WARNI NG
l See smarttech.com/compliance for the projector’s MSDS documents.
l Replace the lamp module when the projector displays its lamp life warning message. If you
continue to use the projector after this message appears, the lamp can shatter or burst,
scattering glass throughout the projector.
l If the lamp shatters or bursts, leave and then ventilate the area.
Next do the following:
o
Avoid touching the glass fragments because they can cause injury.
o
Wash your hands thoroughly if you have come into contact with lamp debris.
o
Thoroughly clean the area around the projector, and discard any edible items placed in
that area because they could be contaminated.
o
Call your authorized SMART reseller for instructions. Do not attempt to replace the
lamp.
l Replacing the lamp module in a wall-mounted projector can result in a fall or injury. Use
caution when climbing a ladder, and consider removing the projector from the wall-
mounting bracket to replace the lamp module.
l Uncovering the lamp while the projector is mounted on the wall-mounting bracket can lead
to product damage or personal injury from falling pieces of glass if the lamp is broken.
26 smar ttech.com/kb/170549
Page 35
CHAPTER 4
Lamp Door
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
l When replacing the projector lamp module:
o
Put the projector into Standby mode and wait 30 minutes for the lamp to cool
completely.
o
Do not remove any screws other than those specified in the lamp replacement
instructions.
o
Wear protective eyewear while changing the lamp module. Failure to do so can cause
injuries including loss of eyesight if the lamp shatters or bursts.
o
Use only replacement lamp modules approved by SMARTTechnologies. Contact your
authorized SMART reseller for replacement parts.
o
Never replace the lamp module with a previously used lamp module.
o
Always handle the fragile lamp assembly with care to prevent premature lamp failure or
exposure to mercury. Use gloves when touching the lamp module. Do not touch the
lamp with your fingers.
o
Recycle or dispose of the lamp module as hazardous waste in accordance with local
regulations.
You need a Phillips No. 2 screwdriver and a flat screwdriver to complete these procedures.
To remove the old lamp module
Press the Power button twice on the remote control to put the projector into Standby
1.
mode.
2. Wait at least 30 minutes for the projector to cool down.
3. Disconnect the power cable from the projector.
4. Use a Phillips screwdriver to loosen the two captive screws.
27 smarttech.com/kb/170549
Page 36
CHAPTER 4
A
B
A
B
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
5. Use a Phillips screwdriver to loosen the two captive screws from the bottom of the lamp
module and gently remove the lamp module.
NOTE
Don’t try to remove these screws. Captive screws can’t be removed, only loosened.
To put the new lamp modu le int o the project or
1. Remove the new lamp module from its packaging.
2. Carefully place the lamp module into the projector and gently press the power end of the
lamp module against the projector to ensure the power plug makes contact with the
projector’s power receptacle.
NOTE
You should be able to place the lamp module into the projector easily without applying
much force.
3. Use the Phillips screwdriver to secure the captive screws.
IMPORTANT
Do not over-tighten the screws.
28 smarttech.com/kb/170549
Page 37
CHAPTER 4
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
4. Replace the lamp cover.
5. Connect the power cable to the wall outlet.
Press the Power button once on the remote control to confirm that the projector is
6.
operating and that the lamp module is correctly installed.
7. Put the old lamp module in a secure container, and handle it gently until you recycle it.
To finish t he projector lamp module installation
1. Turn on the projector.
2. Adjust the projector image if necessary (see
3. Access the service menu to reset the lamp hours (see
Adjusting the image
Resetting the la mp hours
on page19).
below).
4. Activate the projector’s alert e-mails and lamp warnings if they’ve been deactivated (see
mail alerts
on page51 and
Control pa nel
on page46).
Resetting the lamp hours
After you replace the lamp module, you need to access the projector service menu to reset the
lamp hours. To prevent accidental errors, only a system administrator should perform this
procedure.
NOTE
Always reset the lamp hours after you replace the lamp, because lamp service reminders are
based on the current hours of use.
To reset t he lamp hou rs
1. Using the remote control, press the following buttons quickly to access the service menu:
Down, Up, Up, Left, Up.
E-
CAUTION
Do not adjust any settings in the service menu other than those listed in this guide. Changing
other settings can damage or affect the operation of your projector and may invalidate your
warranty.
29 smar ttech.com/kb/170549
Page 38
CHAPTER 4
MAIN TAINI NG YOUR INTERACTIVE WHITEBOARD SYSTEM
2. Scroll down to
Both
Lamp Hour
Lamp Hour Reset
, and then press OK.
values (Standard and Economy) reset to zero.
CAUTION
Do not reset the lamp hours unless you have just replaced the lamp module. Resetting the
lamp hours on an old lamp can damage your projector as a result of lamp failure.
NOTE
You’re unable to reset the
Display Hour
value because it’s the running total of hours the
projector has been in use.
3. Press the Menu button on the remote control.
The
SMART UF70 Settings
Select to confirm that
4.
menu appears.
Lamp Hour
is reset to zero.
30 smarttech.com/kb/170549
Page 39
Chapter 5
whiteboard system
Before you start 32
Locating status lights 32
Locating serial numbers 32
Determining you interactive whiteboard system’s status 33
Resolving interactive whiteboard issues 34
Resolving operation issues 34
Resolving projector issues 35
Resolving projector errors 35
Your projector stops responding 35
The “Projector Overheated”, “Fan Failure”, “Lamp Failure” or “Color Wheel Failure”
message appears 35
The “Lamp Failure” message appears 36
The projector Power and Service lights are off 36
Resolving image issues 37
Loss of signal 37
Partial, scrolling or incorrectly displayed image 38
Unstable or flickering image 39
Frozen image 39
Your image doesn’t fit the interactive whiteboard 40
The image from your connected laptop computer isn’t projected 40
Unaligned projected image 40
Resolving audio issues 40
Resolving network communication issues 41
Accessing the service menu 42
Retrieving your password 42
Resetting the projector 43
Transporting your interactive whiteboard system 43
31 smarttech.com/kb/170549
Page 40
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
This chapter provides basic troubleshooting information for your interactive whiteboard system.
For issues not covered in this chapter, consult the SMARTSupport website
(smarttech.com/support) or contact your authorized SMART reseller (smarttech.com/where).
Before you start
Before you troubleshoot your interactive whiteboard system or contact SMARTSupport or your
authorized SMART reseller for assistance, you need to do the following:
l Locate your interactive whiteboard system’s status lights
l Locate your interactive whiteboard system’s serial numbers
Locating status lights
You interactive whiteboard system consists of several components, which have their own status
lights:
l The Select button on your interactive whiteboard's pen tray also functions as a status light.
Your projector’s Power and Service lights are located on the bottom of the projector.
l
Locating serial numbers
The SMARTBoard M600 interactive whiteboard serial number is located on the lower-right edge
of the frame, as well as on the back of the interactive whiteboard. For more information, see the
SMARTBoard M600 series interactive whiteboa rd user’s guide
(smarttech.com/kb/170410).
32 sma rttech.com/kb/170549
Page 41
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
The SMARTUF70 and UF70w projector's serial number is
located on the top of the projector.
For the locations of serial numbers on other components
and accessories, see smarttech.com/support.
Determining you interactive whiteboard system’s status
Use the following table to determine the status of your interactive whiteboard system.
Pen tray Select
Projector P ower
light
Normal operating statuses
Solid green Off Solid white Correct Full control The system is operating normally.
Flashing green Off Off None None The system is starting up.
Solid am ber Off Off None None The system is in Standby m ode.
Flashing am ber Off Off None None The system is entering Standby
Solid green Off Solid amber N/A None The interactive whiteboard’s
Error statuses
Solid green Off Solid white Incorrect Full control There’s an issue with the projected
Solid green Off Solid white Correct None There’s an issue with the interactive
Projector S ervice
light
button status light
Projected image Touch and pen
control
Stat us and related troubleshooting
If image or sound issues occur, see
the remaining sections of this chapter
for troubleshooting information.
mode.
controller module is ready to receive
a f irmware update or is applying a
firmware update.
image.
See
Resolving image issues
page37.
whiteboard.
See
Resolving operation issues
next page.
on
on the
33 smarttech.com/kb/170549
Page 42
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
Pen tray Select
Projector P ower
light
Solid green Off Flashing white Correct Touch only SMARTProductDrivers isn’t installed
Solid green Off Off N/A N one There’s an issue with the connections
Solid am ber Flashing red N/A None N /A There’s an issue with the projector
Off Flashing red Off None None The projector’s operating
Off Solid red N/A None N/A There’san issue with the projector’s
Off Off Off None None The projector power c able isn’t
Projector S ervice
light
button status light
Projected image Touch and pen
control
Stat us and related troubleshooting
or isn’t running correctly on the
connected computer.
between the interactive whiteboard
and the other components of the
system.
See
Resolving interactive whiteboard
issues
below.
lamp.
See
The “Lamp Failure” message
appears
on page36.
temperature has been exc eeded.
See
The “Projector Overheated”,
“Fan Failure”, “Lamp Failure” or
“Color Wheel Failure” message
appears
on the next page.
fan or color wheel.
See
The “Projector Overheated”,
“Fan Failure”, “Lamp Failure” or
“Color Wheel Failure” message
appears
on the next page.
properly c onnected.
OR
There’s an issue with the m ains power
supply (for example, t he circuit
breaker is off).
Resolving interactive whiteboard issues
This section includes information on resolving issues with your interactive whiteboard.
For information not covered in this section, see the
whiteboard user’s guide
(smarttech.com/kb/170410).
Resolving operation issues
To resolve operation issues, complete the following tasks:
l Confirm that all cables are securely connected to the back of the pen tray, computer and
control module.
34 smarttech.com/kb/170549
SMARTBoard M600 series interactive
Page 43
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
l Perform the calibration procedure documented in the
whiteboard user’s guide
l Reset the interactive whiteboard system by disconnecting the power cable from the wall
(smarttech.com/kb/170410).
SMARTBoard M600 series interactive
outlet and then connecting it.
l If necessary, complete additional troubleshooting with the guidance of SMARTSupport using
SMARTBoard Diagnostics.
l Confirm that the USB cable is properly connected from a fully functional USB receptacle on
the computer to the interactive whiteboard.
Resolving projector issues
Resolving projector errors
System administrators can resolve the following projector errors on their own prior to contacting
SMARTSupport. Performing initial troubleshooting on your projector reduces the time of a support
call.
Your projector stops responding
If your projector stops responding, perform the following procedure.
To restart an unresponsive projector
1. Put the projector into Standby mode, and then wait 30 minutes for it to cool down.
2. Disconnect the power cable from the power outlet, and then wait at least 60 seconds.
3. Connect the power cable, and then turn on the projector.
The “Projector Overheated”, “Fan Failure”, “ Lamp Failure” or “ Color Wheel Failure” message
appears
If the “Projector Overheated”, “Fan Failure” or “Color Wheel Failure” message appears and the
projector stops projecting an image, one of the following issues is occurring:
l The temperature is overheating but the “Projector Overheated” message fails to display.
l The temperature outside the projector is too high.
l One of the fans has failed.
l The projector has a color wheel issue.
35 smarttech.com/kb/170549
Page 44
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
To resolve t he “Project or Overheated”, “Fan Failure”, or “Color Wheel Failure” error
1. Put the projector into Standby mode, and then wait 30 minutes for it to cool down.
2. If your room is hot, lower the temperature if possible.
3. Ensure that nothing is blocking the projector’s air intake and exhaust.
4. Disconnect the power cable from the power outlet, and then wait at least 60 seconds.
5. Connect the power cable, and then turn on the projector.
6. Adjust the fan speed using the service menu.
7. If the previous steps don’t resolve the issue, put the projector into Standby mode, disconnect
the power cable, and then contact your authorized SMARTreseller.
The “Lamp Failure” message appears
If the “Lamp Failure” message appears, one of the following issues is occurring:
l The lamp is overheating, likely due to blocked air vents.
l The lamp has reached the end of its life.
l The projector has an internal problem.
To resolve t he “Lamp Failure” error
1. Restart the projector (see
2. Check the remaining lamp hours using the on-screen menu (see
Your projector stops responding
on the previous page).
Adjusting projector settings
on page12).
If the lamp has more than 2000 hours of use in Standard mode or 3000 hours of use in
Economy mode, it’s near the end of its lifespan.
3. Replace your lamp module as described in
module
on page26.
Removing a nd replacing the projector la mp
4. If replacing the lamp module doesn’t resolve the issue, put the projector into Standby mode,
disconnect the power cable, and then contact your authorized SMARTreseller.
The projector Power and Service lights are off
If the projector Power and Service lights are both off, one of the following issues is occurring:
l There was a power outage or a power surge.
l A circuit breaker or a safety switch was tripped.
36 smarttech.com/kb/170549
Page 45
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
l The projector isn’t connected to the power source.
l The projector has an internal problem.
To resolve t he unlit projector Power and Service lights issue
1. Check the power source, and then make sure that all cables are connected.
2. Confirm that the projector is connected to an active power outlet.
3. Make sure the pins on the connectors aren’t broken or bent.
4. Connect the power cable, and then turn on the projector.
5. If the previous steps don’t resolve the issue, disconnect the power cable and then contact
your authorized SMARTreseller.
Resolving image issues
To resolve common image issues, complete the following tasks:
l Ensure the computer or other video source is on and set to display a resolution and refresh
rate supported by the projector (see
l Ensure the video source is properly connected to the projector.
l Press the I nput button on the remote control or the Inpu t Select button on the pen tray to
Video format
on page77).
switch to the correct video source.
If these tasks don’t resolve the issue, refer to the following sections for additional troubleshooting
information.
Loss of signal
If a video source signal isn’t detected, if it’s out
of range of the projector’s support video
modes or if the signal is being switched to a
different device or input, the projector doesn’t
show a source signal and instead displays the
SMART logo on a blue screen.
37 smar ttech.com/kb/170549
Page 46
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
To resolve signal loss issues
1. Wait approximately 45 seconds for the image to synchronize. Some video signals require a
longer synchronization period. Cycling back through inputs to the one you want also helps
image synchronization.
2. If the image doesn’t synchronize, check your cable connections to the projector.
3. Ensure that the image signal is compatible with the projector (see
Video format
on page77).
4. If there are any extension cables, switch boxes, connection wall plates or other devices in the
video connection from the computer to the projector, temporarily remove them to ensure
they aren’t causing the video signal loss.
5. If your projector still doesn’t show a source signal, contact your authorized SMART reseller.
Part ial, scrollin g or incorrectly displayed image
NOTE
This procedure may vary depending on your version of Windows® operating system or
MacOSX operating system software and your system preferences. The following procedures
apply to Windows 7 operating systems and MacOSX10.8 operating system software.
To resolve a part ial, scrolling or incorrectly displayed image on your Windows computer
1. Select Start > Control Panel.
2. Click Display, and then select Adjust resolution.
3. Verify that your display resolution setting is 1024 × 768 (SMARTUF70 projector), 1280 × 800
(SMARTUF70w projector in 16:10 aspect ratio mode) or 1280 × 720 (SMARTUF70w projector
in 16:9 aspect ratio mode).
4. Click Advanced settings, and then click the Monitor tab.
5. Verify that the screen refresh rate is 60 Hz.
To resolve a part ial, scrolling or incorrectly displayed image on your Mac computer
1. Select Apple Menu > System Preferences.
The
System Preferences
dialog box appears.
2. Click Displays.
3. Verify that your display resolution setting is 1280 × 800 (WXGA).
4. Verify that the screen refresh rate is 60 Hz.
38 smarttech.com/kb/170549
Page 47
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
Unstable or flickering image
If the projector’s image is unstable or flickering, the frequency or tracking settings on your input
source could be different from the settings on your projector.
IMPORTANT
Write down your setting values before adjusting any of the settings in the following procedure.
To resolve your unst able or flickering image
1. Check the display mode of your computer’s graphics card. Make sure it matches one of the
projector’s compatible signal formats (see
Video format
on page77). Refer to your
computer’s manual for more information.
2. Configure the display mode of your computer’s graphics card to make it compatible with the
projector. Refer to your computer’s manual for more information.
3. Adjust the frequency, tracking, H-position and V-position settings in the on-screen menu. See
Adjusting projector settings
on page12.
4. Optionally, reset the projector as described in
Resetting the projector
on page43 to adjust
the frequency and tracking to their original values.
IMPORTANT
This action resets all values to their defaults.
Frozen image
If your projector has a frozen image, perform the following procedure.
To resolve a frozen image
1. Ensure that the Hide Display feature is off.
2. Press the Hide button on the projector’s remote control to hide or show the display.
3. Ensure that your source device, such as your DVD player or computer, isn’t malfunctioning.
4. Put the projector into Standby mode, and then wait 30 minutes for it to cool down.
5. Disconnect the power cable from the power outlet, and then wait at least 60 seconds.
6. Connect the power cable, and then turn on the projector.
7. If the previous steps don’t resolve the issue, contact your authorized SMARTreseller.
39 smarttech.com/kb/170549
Page 48
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
Your image doesn’t fit the int eractive whit eboard
If you’re using a SMARTUF70w projector with a wide screen interactive whiteboard, verify that
you’re using the correct aspect ratio mode for the interactive whiteboard:
Interact ive whit eboard Aspect ratio mode
SMARTBoard M685 interactive whiteboard 16:10
You can set the aspect ratio mode using the Native DLP Resolution setting in the Projector
Functions menu (see
Adjusting projector settings
on page12).
The image from your connected lapt op computer isn’t projected
Laptop computer settings can interfere with projector operations.
Some laptop computers deactivate their screens when you connect a secondary display. Refer to
your computer’s manual for details on reactivating the computer's display screen.
Unaligned projected image
Alignment errors occur when the projected image isn’t perpendicular to the screen. Alignment
errors can occur when you mount your interactive whiteboard system on an uneven surface or a
wall that has obstructions, or if you swivel the projector too far from the vertical center of your
interactive whiteboard.
Use the
SMARTBoard M600i6 interactive whiteboard system installation guide
(smarttech.com/kb/170555) to eliminate most image alignment issues.
The projector image can slip if the projector is moved often or installed in a location prone to
vibration, such as next to a heavy door. Follow these precautions to help prevent the image from
becoming unaligned:
l Make sure that the installation wall is plumb and square and doesn’t move or vibrate
excessively.
l Make sure that there are no obstructions behind the projector’s wall-mounting bracket, and
that the bracket is firmly secured to the wall according to the installation instructions.
l Adjust the projected image. See the
installation guide
(smarttech.com/kb/170555) and
SMARTBoard M600i6 interactive whiteboard system
Adjusting the image
on page19.
Resolving audio issues
NOTE
You might need to configure your computer to pass audio through HDMI if it isn’t configured
automatically.
40 smarttech.com/kb/170549
Page 49
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
To resolve audio issues
1. Ensure that the speakers’ or audio system’s cables are properly connected to the audio
output plug on the projector’s connection panel.
2. Press the Mut e button on the projector’s remote control, and if Audio Mute is on, turn it off.
3. Use the projector’s remote control to ensure that the volume isn’t at the lowest setting.
4. Ensure that your speaker or audio system is on and that the volume is turned up.
5. Check that your source input, such as your computer or video device, isn’t malfunctioning.
Ensure that its audio output is on and that the volume isn’t set to the lowest position.
NOTE
You must display the source input’s video to play its audio through the connected speakers
or audio system.
6. If the previous steps don’t resolve the issue, contact your authorized SMART reseller.
Resolving network communication issues
If you don’t have network access, perform the following procedure to troubleshoot your system.
To resolve network communicat ion issues
1. Ensure that your network cable is properly connected to the RJ45 connection on the
projector’s connection panel. There are two RJ45 ports: one is for the network and one is for
projector 2. Ensure that the network cable is connected to the correct one.
2. Ensure that the LAN warning light on the projector is green. To activate the projector’s
network features, use the “vgaoutnetenable=on” RS-232 command (see
programming commands
Adjusting projector settings
on page55) or enable the Network and VGA Out setting (see
on page12). The network features on the projector don’t work
until you complete one of these tasks.
3. Press the Menu button, and then select the Network Settings menu to check the IP address.
See
Adjusting projector settings
on page12 for a description of the IP address field. Enter this
IP address into your browser or SNMP agent.
4. If you still don’t have network access, contact your network administrator. If your administrator
is unable to resolve the issue, contact your authorized SMART reseller.
Projector
41 smarttech.com/kb/170549
Page 50
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
Accessing the service menu
CAUTION
l To prevent tampering or unintentional changes, only system administrators should access
the service menu. Do not share the service menu access code with casual users of your
interactive whiteboard system.
l Do not adjust any settings in the service menu other than those listed in this guide. Changing
other settings can damage or affect the operation of your projector and may invalidate your
warranty.
Retrieving your password
If you forget the projector’s password, you can retrieve it by accessing the projector service menu
directly from the projector or from the password settings menu on your projector’s web page (see
Password settings
on page52).
To retrieve your password from t he service menu
1. Using the remote control, press the following buttons quickly to access the service menu:
Down, Up, Up, Left, Up.
2. Scroll to
Password Get
, and then press Enter on the remote control.
The password appears on the screen.
3. Write down the password.
4. Scroll to
Exit
, and then press Enter on the remote control to exit the projector service menu.
42 sma rttech.com/kb/170549
Page 51
CHAPTER 5
TROUBLESHOOTIN G YOUR INTER ACTIVE WHITEBOARD SYSTEM
Resetting the projector
At some point during troubleshooting, you might need to reset all projector settings.
IMPORTANT
This action is irreversible.
To reset all projector sett ings
1. Using the remote control, press the following buttons quickly to access the service menu:
Down, Up, Up, Left, Up.
2. Scroll to
3. Scroll to
Factory Reset
Exit
, and then press Enter on the remote control to exit the projector service menu.
, and then press Enter on the remote control.
Transporting your interactive whiteboard system
Save your original interactive whiteboard system packaging so that it’s available if you need to
transport your interactive whiteboard system. When required, repack it with all of the original
packaging. This packaging was designed to provide optimal shock and vibration protection. If you
no longer have your original packaging, purchase the same packaging directly from your
authorized SMART reseller.
If you prefer to use your own packaging materials, make sure you adequately protect your unit.
Make sure that the projector lens and mirror are protected against any physical contact or pressure
which may damage the projector’s optics. Ship your interactive whiteboard in an upright position to
deter shippers from placing heavy objects on it.
43 smarttech.com/kb/170549
Page 52
Page 53
Appendix A
through a network interface
Web page management 45
Accessing web page management 46
Home 46
Control panel 46
Network settings 50
E-mail alerts 51
Password settings 52
Simple Network Management Protocol (SNMP) 52
This chapter includes detailed instructions on how to remotely manage your SMARTBoard
interactive whiteboard system settings through a network interface.
Web page management
You can access advanced setup features via the projector’s web page. This web page enables
you to manage the projector from a remote location using any computer connected to your
intranet.
NOTE
To access the web page, your browser must support JavaScript. Most commonly used browsers
like InternetExplorer®, Chrome™ and Firefox® support JavaScript.
45 smarttech.com/kb/170549
Page 54
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Accessing web page management
Before you can access the web page, connect your projector to the network, and then enable the
projector’s network functions using the projector’s menu. An IP address appears on the on-screen
display.
To use the management web page
1. Start your Internet browser.
2. Type the IP address in the address box, and then press ENTER.
The
SMART UF70 Projector Settings
3. Select the menu options in the left pane to access the settings on each page.
4. Modify settings using your computer’s mouse and keyboard, and then click Submit or another
action button next to each setting you change.
window appears.
Home
The Home menu page displays basic projector information and enables you to select the on-
screen display language.
NOTE
You can view basic projector information but you’re unable to change it (with the exception of
the on-screen display language) from the Home menu page.
Submenu sett ing Description
Language Displays language options
Projector Information Displays current projector information
Control panel
This menu enables you to manage the projector audio and video status, alerts and appearance
using an Internet browser.
Submenu sett ing Description
Power Turns the projector on or puts it into Standby mode. Select the
Power ON or Power OFF button.
46 smarttech.com/kb/170549
Page 55
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Restore All Projector
Defaults
Returns projector settings to default values or refreshes the current
settings. Select Submit or Refresh.
IMPORTANT
The Submit option is irreversible and resets all values.
Volume Adjusts the projector’s volume from -20 to 20.
Mute Turns on or turns off the mute settings. Select On to mute the
projector’s sound and Off to turn off mute.
Volume Control Enables volume control. Select On to enable volume adjustment
and select Off to disable volume adjustment if you prefer to use
your audio system or speaker (not included) controls.
Closed Captioning Turns on or turns off the closed captioning feature.
Language Sets the closed captioning language to CC1 or CC2.
Typically, CC1 displays U.S. English subtitles, while CC2 displays
other regional languages, such as French or Spanish, depending on
television channel or media setup.
Display Mode Adjusts the display output to SMAR T Presentation, Bright Room,
Dark Room, sRGB and User modes so you can project images from
various sources with consistent color performance:
SMAR T Presentation is recommended for color fidelity.
l
BrightRoom and DarkRoom are recommended for locations
l
with those conditions.
sRGB provides standardized accurate color.
l
User enables you to apply your own settings.
l
Brightness Adjusts projector brightness from 0 to 100.
Contrast Adjusts the difference between the lightest and darkest parts
of the image from 0 to 100.
Frequency Adjusts the display data frequency of the projected image from
-5 to 5 to match the frequency of your computer’s graphics card.
Tracking Synchronizes your projector’s display timing with your computer’s
graphics card from 0 to 31.
Sharpness Adjusts the projected image’s sharpness from 0 to 31.
White Peaking Adjusts the image color brightness from 0 to 10 while providing
more vibrant white shades. A value closer to 0 creates a natural
image and a value closer to 10 enhances brightness.
Degamma Adjusts the color performance of the display from 0 to 3.
47 smar ttech.com/kb/170549
Page 56
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Color Adjusts the Red, Green, Blue, Cyan, Magenta and Yellow colors on
the projector from 0 to 100 to provide custom color and luminance
output. Each color has a default value of 100. Adjustments to the
color settings register to the User mode.
Auto Signal Detect Enables or disables signal searching of input connectors.
Select On to have the projector continuously switch inputs until
l
it finds an active video source.
Select Off to maintain signal detection in one input.
l
Lamp Reminder Select On to show or Off to hide the lamp replacement reminder
when it appears. This reminder appears 100 hours before the
recommended lamp replacement.
Lamp Mode Adjusts lamp brightness to Standard or Economy. Standard
displays a high-quality, bright image. Economy increases the lamp
life by decreasing the brightness of the image.
Auto Power Off Sets the length of the auto power off countdown timer between 1
and 240 minutes. The timer begins to count down when the
projector no longer receives a video signal. The timer finishes when
the projector enters Standby mode. Select 0 to turn off the timer.
Zoom Adjusts the zoom to the center of the image in or out from
0 to 30.
H-position (RGB input) Moves the horizontal position of the source video left or right from
0 to 100 (relative to the projected image).
NOTE
This is useful in situations where the source video is cut off.
V-position (RGB input) Moves the vertical position of the source video up or down from -5
to 5 (relative to the projected image).
NOTE
This is useful in situations where the source video is cut off.
48 sma rttech.com/kb/170549
Page 57
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Aspect Ratio Adjusts the image output to Fill Screen, Match Input or 16:9.
Fill Screen produces an image that fills the entire screen by
l
stretching and scaling.
Match Input matches the projector’s aspect ratio to the input’s
l
aspect ratio. As a result, black bands might appear along the
top and bottom edges of the screen horizontally (letterbox
format) or along the left and right edges of the screen vertically
(pillarbox format).
16:9 changes the output to 16:9 by letterboxing the image,
l
which is recommended for use with HDTV and DVDs
enhanced for wide-screen television.
NOTE
See
Video format
on page77 for descriptions of each mode.
Startup Screen Sets the type of startup screen to SMAR T or User. The SMART
screen is the default SMART logo on a blue background. The User
screen uses the saved picture from the Capture User Startup
Screen function.
Video Mute Turns the video mute setting on or off. Select On to hide the display
and Off to show it again.
High Speed Fan Adjusts the speed of the projector’s fan. Select High or Normal.
NOTE
Use the High setting when the projector’s temperature is high or
the altitude is above 6000' (1800 m).
Projector Mode Adjusts the projection mode to Front , Ceiling, Rear or R ear Ceiling.
IMPORTANT
SMART recommends that you never change this setting from the
Ceiling projection mode.
Source Adjusts the input source to VGA-1, VGA-2, Composite, S-Video or
HDMI.
VGA1 Assigns an alternative name to your VGA 1 input, which appears
when you select the VGA 1 input.
VGA2 Assigns an alternative name to your VGA 2 input, which appears
when you select the VGA 2 input.
Composite Assigns an alternative name to your Composite video input, which
appears when you select the Composite video input.
HDMI Assigns an alternative name to your HDMI input, which appears
when you select the HDMI input.
49 smarttech.com/kb/170549
Page 58
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Emergency Alert Turns the on-screen alert broadcast message on or off. When
enabled, this message displays over the current projected image.
Alarm Message / Alert
Message
Displays an on-screen emergency notification message (maximum
60 characters).
Network settings
This menu allows you to use or not use Dynamic Host Control Protocol (DHCP) and to set the
network-related addresses and names when DHCP isn’t used.
Submenu sett ing Description
DHCP Determines if the projector’s IPaddress and other network settings
are dynamically assigned by a DHCPserver or are manually set.
On allows the network’s DHCP server to assign a dynamic IP
l
address to the projector.
Off allows you to manually set the projector’s IP address and
l
other network settings.
IP Address Displays or allows you to set the projector’s IP address in values
between 0.0.0.0 and 255.255.255.255.
Subnet Mask Displays or allows you to set the projector’s subnet mask number in
values between 0.0.0.0 and 255.255.255.255.
Gateway Displays or allows you to set the projector’s default network
gateway in values between 0.0.0.0 and 255.255.255.255.
DNS Displays or allows you to set the projector’s IP address for your
network’s primary domain name server in values between 0.0.0.0
and 255.255.255.255.
Group Name Displays or allows you to set the projector’s workgroup name
(maximum 12 characters).
Projector Name Displays or allows you to set the projector’s name (maximum 12
characters).
Location Displays or allows you to set the projector’s location (maximum 16
characters).
Contact Displays or allows you to set the contact name or number for
projector support (maximum 16 characters).
SNMP Turns the Simple Network Management Protocol (SNMP) agent on
or off.
50 smarttech.com/kb/170549
Page 59
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Read-Only Community Sets a password that is required for each SNMP get request to
thedevice.
NOTE
The default for Read-Only Community is public.
Read/Write Community Sets a password that is required for each SNMP set request to the
device.
NOTE
The default for Read/Write Community is private.
TRAP Destination Address Displays or allows you to set the IP address of the network’s SNMP
TRAP manager in values between 0.0.0.0 and 255.255.255.255.
The TRAP destination address is the IP address of the computer
assigned to handle unsolicited data generated by SNMP TRAP
events generated by the projector, such as power state changes,
projector failure modes, a lamp needing to be replaced or other
issues.
E-mail alerts
This menu enables you to enter your preferred address for receiving e-mail alerts and to adjust
related settings.
Submenu sett ing Description
E-mail Alert Select Enable to turn on or Disable to turn off the e-mail alert
function.
To Displays or allows you to set the e-mail address of the e-mail alert
recipient.
CC Displays or allows you to set the e-mail address of the e-mail alert
“copyto” recipient.
From Displays or allows you to set the e-mail address of the user who
sends the e-mail alert.
Subject Displays or allows you to set the e-mail alert subject.
Outgoing SMTP server Displays or allows you to set the Simple Mail Transfer Protocol
(SMTP) server that you use on your network.
Username Displays or allows you to set the SMTP server user name.
Password Displays or allows you to set the SMTP server password.
51 smarttech.com/kb/170549
Page 60
APPENDIX A
REMOTEL Y MANAGING YOUR SYSTEM THROUG H A NETWOR K INTERFACE
Submenu sett ing Description
Alert Condition Sends e-mail alerts whenever Lamp Warning, Low Lamp Life,
Temperat ure Warning and Fan Lock conditions occur. Select the
settings you want, and then click Submit.
NOTE
The projector sends an alert e-mail (SMART Alert) to your e-mail
address. Click E-mail Alert Test to confirm that your e-mail
address and SMTP server settings are correct by sending a test
e-mail (SMART Alert-Test Mail).
If the settings aren’t correct, the e-mail alert messages aren’t sent
or received successfully and warnings and notification message
aren’t available to advise of this state.
Password settings
This menu provides a security function that allows an administrator to manage projector use and
enable the administrator password function.
Submenu sett ing Description
Password When the password function is enabled, the administrator password
is required to access Web Management. Select D isable to allow
remote web management of the projector without requiring a
password.
NOTES
l The first time you enable the password settings, the default password value is four numbers,
for example, 1234.
l The maximum allowable password length is four numbers or letters.
l If you forget the projector password, refer to
Accessing the service menu
on page42 to set
the projector setting to factory defaults.
Simple Network Management Protocol (SNMP)
Your projector supports a list of SNMP commands as described in the management information
base (MIB) file. You can download this file by browsing to smarttech.com/software and clicking the
MIB file’s link in the
Hardwa re
section for the projector.
The SNMP agent in your projector supports SNMP version 1 or 2. Upload the MIB file to your SNMP
management system application, and then use it as described in your application’s user guide.
52 smar ttech.com/kb/170549
Page 61
Appendix B
through an RS-232 serial interface
Serial interface settings 54
Projector programming commands 55
Projector power state controls 55
Command/response definitions 55
Field definitions 56
Source Application Selection 56
Command/response definitions 56
Field definitions 57
Video control 58
Command/response definitions 58
Field definitions 60
Audio control 63
Command/response definitions 63
Field definitions 64
Network information 65
Command/response definitions 65
Field definitions 66
System information 67
Command/response definitions 67
Field definitions 69
Service Information 73
Command/response definitions 73
Field definitions 74
Unknown command 76
This appendix includes detailed instructions on how to set up your computer or room control
system to remotely manage your SMARTBoard interactive whiteboard system settings through an
RS-232 serial interface.
By connecting a computer or room control system to the interactive whiteboard, you can select
video inputs, start up or shut down your interactive whiteboard system and request information
such as projector lamp use, current settings and network addresses.
53 smarttech.com/kb/170549
Page 62
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Serial interface settings
The serial interface of the projector acts as a Data Communications Equipment (DCE) device and
its settings can’t be configured. You must configure your computer’s serial communication program
(such as Microsoft®HyperTerminal) or your room control system’s serial communication settings
with the following values:
Sett ing Value
Data Rate 19.2 kbps
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
NOTES
l Asynchronous mode is disabled by default in the projector.
l All commands should be in ASCII format. Terminate all commands with a carriage return.
l All responses from the projector are terminated with a command prompt. Wait until you
receive the command prompt indicating that the system is ready for another command
before you proceed.
l The room control feature of the projector is always on.
To configure your comput er’s serial interface
1. Turn on your computer, and then start your serial communications program or terminal
emulation program.
2. Connect your computer to the serial connection cable you previously connected to the
control panel.
3. Configure your serial interface settings using the values from the table above, and then press
ENTER.
An “invalid cmd= ? for help” message appears, and the “>” character appears as a command
prompt on the following line.
IMPORTANT
If no message appears or if an error message appears, your serial interface configuration
is not correct. Repeat step 3.
54 smarttech.com/kb/170549
Page 63
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
4. Type commands to configure your settings.
NOTES
o
To see a list of commands available in the current operating mode, type ? and then
press ENTER.
o
If you’re using a terminal emulation program, turn on your program’s local echo setting
to see characters as you type them.
Projector programming commands
This section documents the projector programming commands and responses.
Projector power state controls
Use these commands to determine the projector power state and related controls.
Command/response definitions
Command Response Responds when powered off
on powerstate=[power state] yes
off [off option] powerstate=[power state] yes
get powerstate powerstate=[power state] yes
55 smar ttech.com/kb/170549
Page 64
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field definitions
Field Possible values D escription
off option now This is an optional field. It forces the projector
to shut down. Once this process starts, you
can’t cancel it. If “now” isn’t specified, the “off”
command causes a countdown to appear. To
turn off the projector, you must send a second
“off” command before the countdown expires;
otherwise the projector, remains on at the end
of the countdown.
NOTE
Consider this as another projector state.
When the countdown is complete, an
asynchronous response indicates that the
projector has returned to the “on” state.
When the projector has turned off, this
command should be accepted but doesn’t do
anything but return the power state.
powerstate
powering
l
on
l
cooling
l
confirm off
l
idle
l
The projector’s current power state. Different
projectors have different potential power
states. These power states match the power
states in the SMART UF70 and SMART UF70w
projectosr.
Source Application Selection
Use these commands to switch between input sources and embedded applications. These
commands also control the USB switch for these sources.
Command/response definitions
Command Response R esponds when powered off
set input [target] input=[current] no
get input input=[current] yes
get videoinputs videoinputs=[current] yes
set usb1source [target] usb1source=[current] yes
get usb1source usb1source=[current] yes
set usb2source [target] usb2source=[current] yes
get usb2source usb2source=[current] yes
56 smar ttech.com/kb/170549
Page 65
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field definitions
Field
current input
target input
Possible values
VGA1
l
Composite
l
HDMI1
l
None
l
= VGA1
l
= Composite
l
= HDMI1
l
= None
l
= Next
l
current videoinputs VGA1, Composite,
HDMI1, etc.
Description
A text list of available video source inputs.
None is a non-selectable input and is returned
in response to a “get input” command when the
projector is turned off.
A text list of possible inputs. Selecting Next
causes the projector to move to the next item
in the list and return a response equivalent to a
user-specified input.
A comma-separated list of available projector
inputs. The strings returned in this command
must match the strings used for the input
selection from the on-screen display (OSD).
VGA1 and HDMI1 are local at the projector.
VGA2 and HDMI2 are at the UCP. The
maximum could be 10 inputs in the current list
(maximum of 14 is reserved).
current usb1source
target usb1source
current usb2source
target usb2source
EXAMPLE
> set input=vga1
input = vga1
VGA1
l
HDMI1
l
Disabled
l
= VGA1
l
= HDMI1
l
= Disabled
l
VGA1
l
HDMI1
l
Disabled
l
= VGA1
l
= HDMI1
l
= Disabled
l
Current value that the USB1 switch is enabled
for.
Value to set the USB1-switch-enabled source
to. If this value is the same as the USB2 source,
the USB1 source is used and the USB2 source is
ignored.
Current value of the USB2 switch.
Value to set the USB2 switch enabled source
to. If this value is the same as the USB2 source,
the USB1 source is used and the USB2 source is
ignored.
57 sm arttech.com/kb/170549
Page 66
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
> set input=next
input = composite
> get videoinputs
videoinputs = vga1, composite, hdmi1
> get usb1source
usb1source = vga1
> get usb2source
usb2source = hdmi1
> set usb2source=hdmi1
usb2source = hdmi1
>
Video control
Use these commands to change your projector's video output controls. The range of values used
for these commands should match the range displayed in the on-screen display (OSD). The
firmware must handle videofreeze and videomute states correctly. A change should be made to
ensure that videofreeze and videomute are mutually exclusive.
Command/response definitions
Command Response Responds when powered off
set displaymode [target] displaymode=[current] no
get displaymode displaymode=[current] no
set brightness [target] brightness=[current] no
get brightness brightness=[current] no
set contrast [target] contrast=[current] no
get contrast contrast=[current] no
set frequency [target] frequency=[current] no
get frequency frequency=[current] no
set tracking [target] tracking=[current] no
get tracking tracking=[current] no
set saturation [target] saturation=[current] no
get saturation saturation=[current] no
set tint [target] tint=[current] no
58 smarttech.com/kb/170549
Page 67
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
get tint tint=[current] no
set sharpness [target] sharpness=[current] no
get sharpness sharpness=[current] no
set hposition [target] hposition=[current] no
get hposition hposition=[current] no
set vposition [target] vposition=[current] no
get vposition vposition=[current] no
set whitepeaking [target] whitepeaking=[current] no
get whitepeaking whitepeaking=[current] no
set degamma [target] degamma=[current] no
get degamma degamma=[current] no
set red [target] red=[current] no
get red red=[current] no
set green [target] green=[current] no
get green green=[current] no
set blue [target] blue=[current] no
get blue blue=[current] no
set cyan [target] cyan=[current] no
get cyan cyan=[current] no
set magenta [target] magenta=[current] no
get magenta magenta=[current] no
set yellow [target] yellow=[current] no
get yellow yellow=[current] no
set videofreeze [target] videofreeze=[current] no
get videofreeze videofreeze=[current] no
set displayhide displayhide= [target] no
get displayhide displayhide= [target] no
59 smar ttech.com/kb/170549
Page 68
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field definitions
Field Possible values D escription
target displaymode
l = SMART
The ranges must match the OSD ranges.
Presentation
l = Bright room
l = Dark room
l = sRGB
l = User
current displaymode
l SMART
The ranges must match the OSD ranges.
Presentation
l Bright room
l Dark room
l sRGB
l User
target brightness
l + val
l – val
l = 0 to 100
Use + or – to change the brightness
incrementally. Enter a number within the range
to set the brightness to a specific level.
current brightness Range: 0 to 100 The device’s current brightness.
target contrast
l + val
l – val
l = 0 to 100
Use + or – to change the contrast incrementally.
Enter a number within the range to set the
contrast to a specific level.
current contrast Range: 0 to 100 The device’s current contrast.
target frequency
l + val
l – val
l = -5 to +5
The ranges must match the OSD ranges.
current frequency Range: -5 to +5 The ranges must match the OSD ranges.
target tracking
l + val
l – val
l = 0 to 31
The ranges must match the OSD ranges.
current tracking Range: 0 to 31 The ranges must match the OSD ranges.
target saturation
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current saturation Range: 0 to 100 The ranges must match the OSD ranges.
60 smarttech.com/kb/170549
Page 69
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target tint
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current tint Range: 0 to 100 The ranges must match the OSD ranges.
target sharpness
l + val
l – val
l = 0 to 31
The ranges must match the OSD ranges.
current sharpness Range: 0 to 31 The ranges must match the OSD ranges.
target hposition
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current hposition Range: 0 to 100 The ranges must match the OSD ranges.
target vposition
l + val
l – val
l = -5 to +5
The ranges must match the OSD ranges. Values
depend upon the source.
current vposition Range: -5 to +5 The ranges must match the OSD ranges.
target whitepeaking
l + val
l – val
l = 0 to 10
The ranges must match the OSD ranges.
current whitepeaking Range: 0 to 10 The ranges must match the OSD ranges.
target degamma
l + val
l – val
l = 0 to 3
The ranges must match the OSD ranges.
current degamma Range: 0 to 3 The ranges must match the OSD ranges.
target red
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current red Range: 0 to 100 The ranges must match the OSD ranges.
target green
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current green Range: 0 to 100 The ranges must match the OSD ranges.
61 smarttech.com/kb/170549
Page 70
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target blue
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current blue Range: 0 to 100 The ranges must match the OSD ranges.
target cyan
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current cyan Range: 0 to 100 The ranges must match the OSD ranges.
target magenta
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current magenta Range: 0 to 100 The ranges must match the OSD ranges.
target yellow
l + val
l – val
l = 0 to 100
The ranges must match the OSD ranges.
current yellow Range: 0 to100 The ranges must match the OSD ranges.
target videofreeze
l = on
l = off
Video freeze on/off
current videofreeze
current displayhide
target displayhide
l = on
l = off
l normal
l frozen
l muted
l normal
l frozen
l muted
l next
Video freeze on/off
Matches the three states of the Hide button on
the remote control.
Set the mode directly or move from one state
to the next sequentially.
Use the above commands to set the property to an absolute value or to adjust the current value.
EXAMPLE
>get brightness
brightness=55
>set brightness = 65
62 smar ttech.com/kb/170549
Page 71
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
brightness=65
>set brightness +5
brightness=70
>set brightness -15
brightness=55
>
All video commands also have an optional source specification. For example, to set the brightness
of a specific source, use the following command.
EXAMPLE
>set brightness = 65
brightness=65
>set brightness vga1 = 65
brightness vga1 = 65
This sets the brightness of the VGA1 source whether the projector is on this source or not.
Audio control
Use these commands to set audio output controls. The range of values used for these commands
should match the range shown in the on-screen display (OSD).
Command/response definitions
Command Response Powered off
set volume [target] volume=[current] no
get volume volume=[current] no
set mute [target] mute=[current] no
get mute mute=[current] no
set volumecontrol
[target]
get volumecontrol volumecontrol=
volumecontrol=
[current]
[current]
no
no
set cc [target] cc=[current] no
get cc cc=[current] no
63 smarttech.com/kb/170549
Page 72
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Command Response Powered off
set sysoutputsw
sysoutputsw=[current] no
[target]
get sysoutputsw sysoutputsw=[current] no
Field definitions
Field Possible values D escription
target volume l + val
l – val
l = -20 to 20
Use + or – to change the volume incrementally.
Enter a number within the range to set the
volume to a specific level. When you modify
the volume using the RS-232, the OSD's
volume slider matches the slider that appears
when you use another control. Note that -20
should map to 0 and 20 should map to 40.
current volume
Range: -20 to 20
The device’s current volume. Note that -20
should map to 0 and 20 should map to 40.
target mute l = on
l = off
current mute l = on
l = off
Specifies whether mute is enabled or disabled.
Current state of the mute function
current volumecontrol l = on
l = off
target volumecontrol l = on
l = off
target cc l = cc1
l = cc2
l = off
current cc l = cc1
l = cc2
l = off
target sysoutputsw l = line+spkr
l = line
l = spkr
l = none
Current state of the volume control
Specifies whether volume control is enabled or
disabled.
Closed captioning states
Closed captioning states
Specifies the system output switch
64 smarttech.com/kb/170549
Page 73
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
current sysoutputsw l = line+spkr
l = line
l = spkr
l = none
Current state of the system output switch
Use the above commands to set the property to an absolute value or to adjust the current value.
EXAMPLE
>get volume
volume=0
>set volume=-10
volume=-10
>set volume +5
volume=-5
>set volume -15
volume=-20
Network information
Use these commands to set your network information.
Command/response definitions
Command Response Powered off
get netstatus netstatus=[current] yes
set network network=[current] yes
get network network=[current] yes
set dhcp [target] dhcp=[current] yes
get dhcp dhcp=[current] yes
set ipaddr [target] ipaddr=[current] yes
get ipaddr ipaddr=[current] yes
set subnetmask
subnetmask=[current] yes
[target]
get subnetmask subnetmask=[current] yes
set gateway [target] gateway=[current] yes
65 smar ttech.com/kb/170549
Page 74
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Command Response Powered off
get gateway gateway=[current] yes
set primarydns [target] primarydns=[current] yes
get primarydns primarydns=[current] yes
get macaddr macaddr=[MAC
yes
address]
Field definitions
Field Possible values D escription
current netstatus l connected
l disconnected
current network l on
l off
target network l on
l off
current dhcp l = on
l = off
target dhcp l on
l off
current ipaddr
Range: 0.0.0.0 to
Current status of the network interface
Current status of the network module and the
VGA output
Enable/Disable network module and VGA
output
Enable/Disable for DHCP Networking
Enable/Disable for DHCP Networking
Current IP address (static or dhcp assigned)
255.255.255.255
target ipaddr
= Range: 0.0.0.0 to
255.255.255.255
current subnetmask
Range: 0.0.0.0 to
255.255.255.255
target subnetmask
= Range: 0.0.0.0 to
255.255.255.255
current gateway
Range: 0.0.0.0 to
255.255.255.255
target gateway
= Range: 0.0.0.0 to
255.255.255.255
current primarydns
Range: 0.0.0.0 to
255.255.255.255
66 smar ttech.com/kb/170549
Set to static IP Address
Current subnet Mask
Target subnet Mask
Current gateway
Target gateway
Current primary dns
Page 75
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target primarydns
= Range: 0.0.0.0 to
Target primary dns
255.255.255.255
MAC address
xx-xx-xx-xx-xx-xx
The device’s MAC address.
System information
Use these commands to set your system information.
Command/response definitions
Command Response Powered off
set autosignal [target] autosignal=[current] no
get autosignal autosignal=[current] no
set lampreminder
[target]
get lampreminder lampreminder=
set highbrightness
[target]
lampreminder=
[current]
[current]
highbrightness=
[current]
no
no
no
get highbrightness highbrightness=
no
[current]
set autopoweroff
autopoweroff=[current] no
[target]
get autopoweroff set
autopoweroff=[current] no
zoom [target]
set zoom [target] zoom=[current] no
get zoom zoom=[current] no
set projectorid [target] projectorid=[current] no
get projectorid projectorid=[current] no
set aspectratio [target] aspectratio=[current] no
get aspectratio aspectratio=[current] no
set projectionmode
[target]
projectionmode=
[current]
no
67 sm arttech.com/kb/170549
Page 76
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Command Response Powered off
get projectionmode projectionmode=
no
[current]
set startupscreen
startupscreen=[current] no
[target]
get startupscreen startupscreen=[current] no
set restoredefaults restoredefaults=
yes
[current]
get lamphrs lamphrs=[current] yes
set lamphrs [target] lamphrs=0 yes
get syshrs syshrs=[current] yes
get resolution resolution=[current] no
get nativeaspectratio nativeaspect=[native] no
get fwverddp fwverddp=[current] yes
get fwvernet fwvernet=[current] yes
get fwvermpu fwvermpu=[current] yes
get serialnum serialnum=[current] yes
get fwverecp fwverecp=[current] yes
set language [target] language=[current] no
get language language=[current] no
set groupname [target] groupname=[current] no
get groupname groupname=[current] no
set projectorname
[target]
get projectorname projectorname=
projectorname=
[current]
no
no
[current]
set locationinfo [target] locationinfo=[current] no
get locationinfo locationinfo=[current] no
set contactinfo [target] contactinfo=[current] no
get contactinfo contactinfo=[current] no
get modelnum modelnum=UF70, or
modelnum=UF70w
no
Returns the actual model of the projector
68 smarttech.com/kb/170549
Page 77
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Command Response Powered off
set videomute [target] videomute=[current] no
get videomute videomute=[current] no
set vgaoutnetenable
[target]
get vgaoutnetenable vgaoutnetenable=
vgaoutnetenable=
[current]
yes
yes
[current]
set
emergencyalertmsg
emergencyalertmsg=
[current]
no
[target]
get
emergencyalertmsg
set emergencyalert
[target]
get emergencyalert emergencyalert=
emergencyalertmsg=
[current]
emergencyalert=
[current]
no
no
no
[current]
get signaldetected signaldetected=
[current]
yes
The response varies depending on the power
mode.
Field definitions
Field Possible values D escription
target autosignal
current autosignal
target lampreminder
current lampreminder
target highbrightness
current highbrightness
69 smar ttech.com/kb/170549
l
l
l
l
l
l
l
l
l
l
l
l
= on
= off
on
off
= on
= off
on
off
= on
= off
on
off
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
Page 78
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target autopoweroff
current autopoweroff
target zoom
current zoom
target projectorid
current projectorid
target aspectratio
+ val
l
– val
l
= 0 to 240
l
+ val
l
– val
l
= 0 to 240
l
+ val
l
– val
l
= 0 to 30
l
= 0 to 30 The ranges must match the OSD ranges.
l
+ val
l
– val
l
= 0 to 999
l
= 0 to 999 The ranges must match the OSD ranges.
l
= fill
l
= match
l
= 16:9
l
The ranges must match the OSD ranges.
The ranges must match the OSD ranges.
The ranges must match the OSD ranges.
The ranges must match the OSD ranges.
The ranges must match the OSD ranges.
Fill:
Regardless of the input, the image is stretched
to match the DMD device. For example, a 16:9
image appears as a 4:3 image on an XGA
projector and as a 16:10 image on a WXGA
projector.
current aspectratio
70 smarttech.com/kb/170549
l
l
l
fill
match
16:9
Match:
The signal is scaled so that the input aspect
ratio is maintained. For example, a 4:3 image
appears as a 4:3 image on screen.
16:9
The signal is scaled and stretched to produce a
16:9 image.
The ranges must match the OSD settings.
Page 79
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target projectionmode
current
projectionmode
target startupscreen
current startupscreen
current reset
current lamphrs
= front
l
= ceiling
l
= rear
l
= rear ceiling
l
= front
l
= ceiling
l
= rear
l
= rear ceiling
l
= smart
l
= usercapture
l
= preview
l
= smart
l
= usercapture
l
= preview
l
done Sent once you reset the projector.
l
0 to 5000 Current lamp hour usage
l
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
The ranges must match the OSD settings.
target lamphrs 0 Clear the current lamp hour usage. The only
valid value is 0.
current resolution
native aspect ratio 4:3 for SMART UF70,
800x600
l
1024x768
l
…
l
no signal
l
16:10 for SMART
UF70w
Current resolution of the input. If no signal is
detected, “resolution=no signal” appears.
Native aspect ratio. DLP resolution of the
projector. Returns the actual native aspect ratio
of the projector.
current fwverddp x.x.x.x Firmware version
current fwvernet x.x.x.x Network processor version
current fwvermpu x.x.x.x MPU version
current prjserialnum xxxxxxxxxxxxx Projector serial number
current fwverecp x.x.x.x ECP version, if present
71 smar ttech.com/kb/170549
Page 80
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
current language
Arabic
l
Chinese
l
(Simplified)
Chinese
l
(Traditional )
Czech
l
Danish
l
Dutch
l
English
l
Finnish
l
French
l
German
l
Greek
l
Hindi
l
Italian
l
Japanese
l
Korean
l
Norwegian
l
(Norsk)
Polish
l
Portuguese
l
(Brazil)
Portuguese
l
(Portugal)
Russian
l
Spanish
l
Swedish
l
Must match the OSD setting
target language = above Must match the OSD setting
target groupname = user string
current groupname user string
target projectorname = user string
current projectorname user string
target locationinfo = user string
current locationinfo user string
72 smarttech.com/kb/170549
Page 81
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field Possible values D escription
target contactinfo = user string
current contactinfo user string
current modelnum user string Must match the OSD setting
current videomute
target videomute
current
vgaoutnetenable
target
vgaoutnetenable
current
emergencyalertmsg
target
emergencyalertmsg
current
emergencyalert
target
emergencyalertmsg
l
l
l
l
l
l
l
l
on
off
= on
= off
on
off
= on
= off
Must match the OSD setting.
Must match the OSD setting.
Status of VGA Out Enable and Network Enable
Value for VGA Out and Network Enable
User string Emergency Alert message
= User string Set the Emergency Alert message
l
l
l
l
on
off
= on
= off
To display the alert message, set this value to
“on.”
If the message is being displayed, “on” is
returned.
current signaldetected
l
l
true
false
If a signal is detected, “true” is returned.
Command List .... A list of commands appears. This list doesn’t
include service information commands.
Service Information
These commands are used in servicing and manufacturing the projector. They are hidden from the
user during normal operation.
Command/response definitions
Command Response Powered off
get displayhour displayhour=[current] no
73 smar ttech.com/kb/170549
Page 82
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Command Response Powered off
set testpattern [target] testpattern=[current] no
set colorwheelidx
[target]
get colorwheelidx colorwheelidx=
colorwheelidx=
[current]
no
no
[current]
get failurelog failurelog=[current] yes
get error# error#=[current] yes
set factoryreset
factoryreset=[current] yes
[target]
set highspeedfan
[target]
get highspeedfan highspeedfan=
highspeedfan=
[current]
no
no
[current]
set statereporting
[target]
get statereporting statereporting=
statereporting=
[current]
yes
yes
[current]
get poweroverride poweroverride=
no
[current]
set poweroverride
[target]
poweroverride=
[current]
no
Field definitions
Field
Possible Values
Description
current displayhour 0 to 20000 Current display hours.
target testpattern = 1 to 4 Set the test pattern to pattern number (1 to 4). If
there’s only one test pattern, call it test pattern
1.
current testpattern
1: Grid
l
2: Red
l
3: Green
l
4: Blue
l
5: Grey
l
6: Black
l
Test pattern being displayed. The built-in test
pattern can be changed.
74 smar ttech.com/kb/170549
Page 83
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field
Possible Values
Description
target colorwheelidx = ??? The ranges must match the OSD ranges.
current colorwheelidx ??? The ranges must match the OSD ranges.
current failurelog
Current error# Provide the details of
normal
l
overtemp
l
fanlock
l
fanDMD
l
fanblower
l
fansystem
l
lamperror
l
colorwheelbreak
l
lampignite
l
lampoverheat
l
lampdriver
l
lampoverhours
l
the specific error. “#”
is the number
recorded in the log. It
ranges from 1 to 5. 1
indicates the most
recent error and 5
Projector's error state. The modes are projector
dependent.
The details include the failure reason, system
hours, lamp hours, sensor temperature and
lamp voltage.
Example: error1=fansystem, syshrs:1000,
lamphrs=1000, temp=60,volt=120.
error2=lampoverheat, syshrs:3000,
lamphrs=2900, temp=150,volt=120.
indicates the oldest
error.
target factoryreset
current factoryreset
target highspeedfan
current highspeedfan
current statereporting
75 sm arttech.com/kb/170549
= true
l
= false
l
= true
l
= false
l
= high
l
= normal
l
high
l
normal
l
on
l
off
l
If set to “true,” perform a factory reset.
Otherwise, do nothing.
Set to “true” only if a factory reset is about to
occur.
Must match the OSD settings.
Must match the OSD settings.
Current state reporting value
Page 84
APPENDIX B
REMOTEL Y MANAGING YOUR SYSTEM THROUG H AN RS-232 SERIAL I NTERFACE
Field
target statereporting
current poweroverride
Possible Values
= on
l
= off
l
on
l
off
l
Description
Target state reporting value
A power override forces the projector to
remain on when the command is received. This
command isn’t persistent and isn’t stored to
non-volatile memory (cleared on power cycle).
When this mode is enabled, the power button
on the remote control and the ECP, if present,
must not turn off the projector.
This command must also be added to the
service menu so the user can disable it from the
OSD.
target poweroverride
l
l
= on
= off
Sets the power override
Unknown command
If an unknown command is received, the projector sends the following response to the user (there
is a space between “invalid” and “cmd”).
>dummycommand 2134
invalid cmd=dummycommand 2134
76 sm arttech.com/kb/170549
Page 85
Appendix C
Video format 77
Native video format 77
Video format compatibility 78
SMARTUF70 projector 78
SMARTUF70w projector 79
HD and SD signal format compatibility 81
SMARTUF70 projector 81
SMARTUF70w projector 81
Video system signal compatibility 82
SMARTUF70 projector 82
SMARTUF70w projector 82
Connecting peripheral sources and outputs 83
This appendix provides information on integrating your SMARTBoard interactive whiteboard
system with peripheral devices.
Video format
Your projector has a native video format and various video format compatibility modes. You can
change image appearances for certain formats and compatibilities.
Native video format
The following table lists the native VESA RGB video formats for the projector.
Projector Resolut ion Mode Aspect
rat io
SMARTUF70 1024 × 768 XGA 4:3 60 48 63.5
77 sma rttech.com/kb/170549
Refresh rate
(Hz)
Hor izontal
frequency
(kHz)
Pixel clock
(MHz)
Page 86
APPENDIX C
INTEGRATIN G OTHER DEVICES
Video format compatibility
The following tables list the projectors’ compatible VESA RGB video formats by resolution, which
the projector adjusts automatically when you use the aspect ratio commands described in
Adjusting projector settings
SMAR TUF70 projector
Resolution Mode Aspect ratio Refresh rat e (Hz) Match In put
720 × 400 720×400_85 1.8:1 85.039 Letterbox
640 × 480 VGA 60 4:3 59.94 Full screen
640 × 480 VGA 72 4:3 72.809 Full screen
640 × 480 VGA 75 4:3 75 Full screen
640 × 480 VGA 85 4:3 85.008 Full screen
800 × 600 SVGA 56 4:3 56.25 Full screen
on page12.
appearance
800 × 600 SVGA 60 4:3 60.317 Full screen
800 × 600 SVGA 72 4:3 72.188 Full screen
800 × 600 SVGA 75 4:3 75 Full screen
800 × 600 SVGA 85 4:3 85.061 Full screen
832 × 624 MAC 16" 4:3 74.55 Full screen
1024 × 768 XGA 60 4:3 60.004 Full screen
1024 × 768 XGA 70 4:3 70.069 Full screen
1024 × 768 XGA 75 4:3 75.029 Full screen
1024 × 768 XGA 85 4:3 84.997 Full screen
1024 × 768 MAC 19" 4:3 74.7 Full screen
1152 × 864 SXGA1 75 4:3 75 Full screen
1280 × 720 HD 720 16:9 60 Letterbox
1280 × 768 SXGA1 75 1.67:1 60 Letterbox
1280 × 800 WXGA 16:10 60 Letterbox
1280 × 960 Quad VGA 60 4:3 60 Full screen
1280 × 960 Quad VGA 85 4:3 85.002 Full screen
1280 × 1024 SXGA3 60 5:4 60.02 Letterbox
1280 × 1024 SXGA3 75 5:4 75.025 Letterbox
78 smarttech.com/kb/170549
Page 87
APPENDIX C
INTEGRATIN G OTHER DEVICES
Resolution Mode Aspect ratio Refresh rat e (Hz) Match In put
appearance
1280 × 1024 SXGA3 85 5:4 85.024 Letterbox
1360 × 765 1.04M9 16:9 59.799 Letterbox
1600 × 900 1.44M9 16:9 59.946 Letterbox
1600 × 1200 UXGA 4:3 60 Full screen
1680 × 1050 1680x1050 50 16:10 49.974 Letterbox
1680 × 1050 1680x1050 50 16:10 59.954 Letterbox
1920 × 1080 HD 1080 16:9 60 Letterbox
SMAR TUF70w projector
Resolution Mode Aspect
rat io
Refresh
rat e (Hz)
Match Input
appearance
(16:10 aspect
rat io mode)
Match Input
appearance
(16:9 aspect
rat io mode)
720 × 400 720×400_85 9:5 85.039 Letterbox Letterbox
640 × 480 VGA 60 4:3 59.94 Pillarbox Pillarbox
800 × 600 VGA 72 4:3 72.809 Pillarbox Pillarbox
800 × 600 VGA 75 4:3 75 Pillarbox Pillarbox
800 × 600 VGA 85 4:3 85.008 Pillarbox Pillarbox
800 × 600 SVGA 56 4:3 56.25 Pillarbox Pillarbox
800 × 600 SVGA 60 4:3 60.317 Pillarbox Pillarbox
800 × 600 SVGA 72 4:3 72.188 Pillarbox Pillarbox
800 × 600 SVGA 75 4:3 75 Pillarbox Pillarbox
800 × 600 SVGA 85 4:3 85.061 Pillarbox Pillarbox
832 × 624 MAC 16" 4:3 74.55 Pillarbox Pillarbox
1024 × 768 XGA 60 4:3 60.004 Pillarbox Pillarbox
1024 × 768 XGA 70 4:3 70.069 Pillarbox Pillarbox
1024 × 768 XGA 75 4:3 75.029 Pillarbox Pillarbox
1024 × 768 XGA 85 4:3 84.997 Pillarbox Pillarbox
1024 × 768 MAC 19" 4:3 74.7 Pillarbox Pillarbox
79 sm arttech.com/kb/170549
Page 88
APPENDIX C
INTEGRATIN G OTHER DEVICES
Resolution Mode Aspect
rat io
Refresh
rat e (Hz)
Match Input
appearance
(16:10 aspect
rat io mode)
Match Input
appearance
(16:9 aspect
rat io mode)
1152 × 864 SXGA 75 4:3 75 Pillarbox Pillarbox
1280 × 768 WXGA 60 1.67:1 60 Letterbox Pillarbox
1280 × 960 Quad VGA 60 4:3 60 Pillarbox Pillarbox
1280 × 960 Quad VGA 85 4:3 85.002 Pillarbox Pillarbox
1280 × 960 SXGA3 60 5:4 60.02 Pillarbox Pillarbox
1280 × 1024 SXGA3 75 5:4 75.025 Pillarbox Pillarbox
1600 × 1200 SXGA+ 4:3 59.978 Pillarbox Pillarbox
1600 × 1200 UXGA_60 4:3 60 Pillarbox Pillarbox
80 smarttech.com/kb/170549
Page 89
APPENDIX C
INTEGRATIN G OTHER DEVICES
HD and SD signal format compatibility
The following tables list the projectors’ high definition (HD)and standard definition (SD) format
signal compatibility, which the projector adjusts automatically when you use the aspect ratio
commands described in
SMAR TUF70 projector
Adjusting projector settings
on page12.
Signal for mat Aspect rat io Horizontal
frequency (kHz)
480i (DVD player)
4:3 15.73 59.94 Full screen
Vertical
frequency (Hz)
Match Input
appearance
(640 × 480)
567i (DVD player)
5:4 15.63 50 Letterbox
(720 × 576)
720p 16:9 44.96 59.94 Letterbox
720p 16:9 35 50 Letterbox
1080i 16:9 33.7 59.94 Letterbox
1080i 16:9 28.1 50 Letterbox
SMAR TUF70w projector
Signal for mat Aspect
rat io
Hor izontal
frequency
(kHz)
Vertical
frequency
(Hz)
Match Input
appearance
(16:10 aspect
rat io mode)
Match Input
appearance
(16:9 aspect
rat io mode)
480i (525i) 4:3 15.73 59.94 Pillarbox Pillarbox
480p (525p) 4:3 31.47 59.94 Pillarbox Pillarbox
576i (625i) 5:4 15.63 50 Pillarbox Pillarbox
576p (625p) 5:4 31.25 50 Pillarbox Pillarbox
720p (750p) 16:9 45 59.94 Letterbox Full screen
720p (750p) 16:9 37.5 50 Letterbox Full screen
1080i (1125i) 16:9 33.75 59.94 Letterbox Full screen
1080i (1125i) 16:9 28.13 50 Letterbox Full screen
1080p (1125p) 16:9 67.5 59.94 Letterbox Full screen
1080p (1125p) 16:9 56.25 50 Letterbox Full screen
81 smarttech.com/kb/170549
Page 90
APPENDIX C
INTEGRATIN G OTHER DEVICES
NOTE
Your projector is HD-ready. Its native resolution supports a pixel-perfect display of 720p source
content. However, because the projector compresses 1080p source content to fit its native
resolution, it doesn’t support a pixel-perfect display of 1080p source content.
Video system signal compatibility
The following tables list the projectors’ video system signal compatibility, particularly for signals
delivered over S-Video and Composite video connectors, which the projector adjusts
automatically when you use the aspect ratio commands described in
on page12.
NOTE
The 16:9 command delivers all video modes with black bands along the top and bottom edges
of the screen. The Match Input command might deliver video modes with black bands along the
top and bottom edges of the screen, depending on the input resolution.
Adjusting projector settings
SMAR TUF70 projector
Video mode Aspect rat io Hor izontal
frequency (kHz)
Vertical
frequency (Hz)
Color signal
(MHz)
NTSC 4:3 15.73 29.96 3.58
PAL 4:3 15.62 25 4.43
SECAM 4:3 15.62 25 4.25 (fob)
4.06 (for)
SMAR TUF70w projector
Video mode Aspect ratio Horizont al
frequency (kHz)
Vertical
frequency (Hz)
Color signal
(MHz)
NTSC 4:3 15.73 59.94 3.58
PAL 4:3 15.63 50 4.43
SECAM 4:3 15.63 50 4.25 and 4.41
PAL-M 4:3 15.73 59.94 3.58
PAL-N 4:3 15.63 50 3.58
PAL-60 4:3 15.73 59.94 4.43
NTSC 4.43 4:3 15.73 59.94 4.43
82 smarttech.com/kb/170549
Page 91
APPENDIX C
INTEGRATIN G OTHER DEVICES
Connecting peripheral sources and outputs
Follow these instructions if you have a peripheral device to connect to your interactive whiteboard
system, such as a DVD/Blu-ray player.
NOTE
Measure the distance between the projector and the peripheral device you want to connect.
Make sure each cable is long enough, has plenty of slack and can be placed safely in your room
without presenting a trip hazard.
To connect a peripheral sou rce or output to your projector
1. Connect your peripheral device’s input cables to the projector.
2. Switch input sources to the peripheral device by pressing the Input button on the remote
control.
83 smarttech.com/kb/170549
Page 92
Page 93
Appendix D
IR signal format: NEC1
Key Repeat
format
Input F1 8B CA 14 EB
Power ( )
Menu F1 8B CA 1B E4
Up ( ) F1 8B CA 40 BF
Left ( ) F1 8B CA 42 BD
Enter ( ) F1 8B CA 13 EC
Right ( ) F1 8B CA 43 BC
Down ( ) F1 8B CA 41 BE
Hide F1 8B CA 15 EA
Volume up ( ) F1 8B CA 44 BB
Mode F1 8B CA 45 BA
Mute F1 8B CA 11 EE
Volume down ( ) F1 8B CA 46 B9
F1 8B CA 12 ED
Vendor code Key code
Byte 1 Byte 2 Byte 3 Byte 4
85 smarttech.com/kb/170549
Page 94
Page 95
Appendix E
compliance
SMARTTechnologies supports global efforts to ensure that electronic equipment is manufactured,
sold and disposed of in a safe and environmentally friendly manner.
Waste Electrical and Electronic Equipment and
Battery regulations (WEEE and BatteryDirectives)
Electrical and electronic equipment and batteries contain substances that can be harmful to
the environment and to human health. The crossed-out wheeled bin symbol indicates that
products should be disposed of in the appropriate recycling stream and not as regular
waste.
Batteries
Remote contains CR2025 battery. Recycle or dispose of batteries properly.
Perchlorate material
Contains perchlorate material. Special handling may apply. See
dtsc.ca.gov/hazardouswaste/perchlorate.
Mercury
The lamp in this product contains mercury and must be recycled or disposed in accordance
with local, state, provincial and federal laws.
More information
See smarttech.com/compliance for more information.
87 smarttech.com/kb/170549
Page 96
Page 97
Index
3
3.5 mm audio connectors 20
A
accessories
included 4
optional 4
alarms 50
aspect ratios 15, 49, 77-79, 81-82
audio
connections for 20
controlling volume of 47
muting 11
resolving issues with 40
B
batteries 10, 87
Blu-ray players 83
C
cameras 83
closed captioning 47
composite video connections 49, 82
connection diagrams
projector 19
contact person 50
D
DHCP 16, 50
display modes 11-12, 47
DNS 50
document cameras 83
dust iv
DVD players 83
E
e-mail alerts 51
electrostatic discharge iv
emergency alerts 50
emissions iv
environmental requirements iii
F
fans 35, 49
flickering 39
focus 18
H
HD signal compatibility 81
HDMI connections 20, 49
head space clearance 6
height 6
humidity iv
I
image
adjusting 19
focusing 18
resolving issues with 37
input selection 49
installation
choosing a height 6
89 smarttech.com/kb/170549
Page 98
INDEX
choosing a location 5
interactive whiteboard
about 2
indicators and controls of 34
maintaining 23
using 21
IP address 16, 46, 50
L
lamp module
cleaning 24
replacing 26
resolving issues with 36
languages 47
laptop computers
troubleshooting issues with 40
letterboxing 78-79, 81
light sources 5
location 5, 50
Perchlorate material 87
peripheral sources 83
pillarboxing 78-79, 81
power 20, 46, 55
projector
about 3
adjusting settings for 12
adjusting the image of 19
cleaning 24
connection diagram for 19
displaying the name of 50
focusing the image of 18
installing 5
lights and status of 32
locating the serial number on 32
remotely managing 45, 53
replacing the lamp of 26
routing cables from 6
securing to the boom 6
using your remote control with 9
video format compatibility for 77
M
MAC support 78-79
mercury 87
mounting template 6
mute control 11, 13, 47
N
native video formats 77
network communication 20, 41, 50
O
options 4
original packaging 43
P
passwords 16, 42, 51-52
pens 4
Q
quad VGA support 78-79
R
RCA jacks 20
refresh rates 77-79
remote control
about 4
code definitions for 85
installing the battery 10
using the buttons 11
RJ45 connector 20
room control 45, 53
RS-232 serial interface 20
S
S-video connections 82
SD signal compatibility 81
90 smarttech.com/kb/170549
Page 99
INDEX
serial interface SeeRS-232 serial interface
serial number 32
signal loss 37
SMART Board interactive
whiteboard Seeinteractive
whiteboard
SMART UF70 or UF70w
projector Seeprojector
SMART UF70 projector Seeprojector
SMTP 51
SNMP 52
sound Seeaudio
startup screen 49
subnet mask 16, 50
SVGA support 78-79
SXGA support 78-79
T
temperatures, operating and storage iii
transportation 43
TRAP destination address 51
troubleshooting 31
water and fluid resistance iv
web page management 45
WEEE and Battery Directives 87
whiteboard Seeinteractive whiteboard
X
XGA support 78-79
Z
zoom 48
U
UF70 or UF70w projector Seeprojector
UF70 projector Seeprojector
USB receptacles 20
UXGA support 78-79
V
VGA connections 20, 49
VGA support 78-79
video
connections for 20
format compatibility for 77
W
warnings iii
91 smarttech.com/kb/170549
Page 100
Loading...