SMART Cordless TL-2100G Installation And Use Instruction

Pa

d Signa

l

L

os

t

L

o

w

B

at

tery

P

a

d

2

Mo

n

i

t

or

N

o

t

In

Use

P

a

d

1

Pa

d Signal
L

os

t

L

o

w B

atter

y

Pa

d

2

Mo

nito

r

N

o

t

I

n

Use

Pa

d

1

Reset

Quick Start Instructions

TL-2100G

Need Set-up Help? [phone]

AA Battery

+

-

Melody

3 2 1

Volume

Decrease/Increase

AA Battery

+

-

AA Battery

+

-

The CordLess® Monitor can work in two modes:

1. With one CordLess® bed or chair sensor pad

2. With two CordLess® bed sensor pads

Install Battery, Adjust Settings

1

Program Sensor Pad(s)

2

3

A. Test Pad 1

B. Test Pad 2

Program
Button

Pad 1

Pad 2

Reset

Low Battery

Status/
In Use

Check

Pad

Pad Signal

Lost

Low Battery

Pad 2

Monitor Not

In Use

Pad 1

Pad Signal

Lost

Low Battery

Pad 2

Monitor Not

In Use

Pad 1

Remove the protective boot.
Insert batteries as shown.

CordLess Monitor settings:
Volume, Melody

Close the battery door and
secure it with the small
Phillips-head screw.

Place the monitor in its
protective plastic boot.

Resetting the Monitor/Tamper Proof™ Mode with Caregiver Key

™

(Optional)

Test the System for each Pad

Caregivers can choose to reset the
CordLess Monitor in either of two ways:

Option 2 allows only the caregiver to
reset the monitor.

For more informati on about
the Care giver Key™ a nd how it c an
be use d in your f acility ’s Fall R isk
Assess ment Program call
800-650-3637

IMPORTANT: W hen using the

TL-2100G CordLess® Monitor with two pads,
place all the components (the two pads and the monitor) within 15 feet of each
other. Test the system before each use.

When using “Reset Button ON” Mode

Press the Reset/Low Battery button to
reset the monitor.

When using “Reset Button OFF”

Place the Caregiver Key™ over the red dot to
reset the monitor.

Alert Tone/Melody Adjustment

Default Setting: Melody 1

Alert Volume Dial

Default Setting: Full Volume

Reset
Button

Monitor ready to

program

Pad 1

Monitor ready to

program Pad 2

Exit Programming
for single pad use

Program 2nd pad

Option 1

OR

Option 2

SMART CAREGI VER CORPORATION

Tel: [phone] | www.smart caregivercorp.com

Reset

Low Battery

PR

OGR

A

M

TL-200GU R2

Pad Signal

Lost

Low Battery

Pad 2

Monitor Not

In Use

Pad 1

Pad Signal

Lost

Low Battery

Pad 2

Monitor Not

In Use

Pad 1

Reset

Pad Signal

Lost

Low Battery

Pad 2

Monitor Not

In Use

Pad 1

(See separa te instruction s for Co rdLess® Floor M at opera tion)

Place one or two CordLess bed or chair pads within reach. Each sensor
pad comes with a CordLess Transmitter connected and turned on.

Press and hold the Program Button on the back of the monitor until
you hear 3 short beeps to enter programming mode. Release the
button.

Press and hold t he Program

Button until yo u hear 3 short

beeps to enter program ing

mode.

Apply pressure to pad

Monitor will beep two times

Status light will blink while pressure remains on pad

When pressure is removed, monitor will alarm

Press reset button to silence alarm or use caregiver key depending on your setting.

See switch on side of monitor to select the
option of your choice.

“Reset Switch ON”: Pressing the

Reset/Low Battery button on the
front of the monitor.

“Reset Switch OFF”: Placing the

optional Caregiver Key over the red
dot on the front of the monitor.

Reset

Reset

Reset

Reset

Reset

0.3A

Place pressure on rst

pad for 3 seconds,

then release to

program as Pad 1.

Monitor beeps twice.

Place pressure on second pad for 3

seconds then release to program as

Pad 2. Monitor beeps twice.

Press the Reset Button to

exit programming.

*NOTE: When there are 2 pads programmed to the monitor and
no one is on the pads, press the reset button twice to reset the
monitor.

Place pressure o n

program as Pad 1.

Monitor will beep

twice.

CordLess® Fall/Mobility Monitor TL-2100G

Need Set-up Help? [phone]

CAUTIO N: If using this monitor with Change Pad Indicator™ Timed Sensor Pads, this monitor will not indicate when pad life has expired. Pads will
still function normally. Call [phone] for more information.

WARNING: Failure to comply with warning may result in injury or death. This device is not suitable for all individuals. Other devices may be required.
This device is not a substitute for visual monitoring by caregiver. The manufacturer does not claim that this device will stop elopement and/or stop
falls. This device is designed to augment caregivers’ comprehensive resident mobility management program. Test this device before each use. Read

the instructions and Legal Disclaimer.

The Smart Caregiver Corporation TL-2100G CordLess® Monitor is designed to be installed by the end user. As such, it is the entire responsibility of the
buyer to insure that the system is properly in

stalled and tested. Further, the system is not designed to replace good caregivi gn

practices including, but n

ot limited to:

A.) Direc t patient supervision

C.) Testing of the sys tem before each use

WHERE PERMISSIBLE, IT IS THE SELLER’S INTENT TO LIMIT ANY LIABILITY FOR SPECIAL, CONSEQUENTIAL OR INCIDENTAL ECONOMIC DAMAGES TO
REFUND OF THE PURCHASE PRICE OR REPLACEMENT OF THE GOODS. SELLER DISCLAIMS ANY LIABILITY FOR COMPENSATORY OR OTHER DAMAGES
ARISING OUT OF THE USE OF THE GOODS.

WARNING: The manufacturer does not claim that this device will stop elopement and/or stop falls. This device is designed to augment caregivers’
comprehensive resident mobility management program. This product is to be used by a licensed caregiver only.

Limited Warranty: Seller warrants that the goods sold will be free from defects of workmanship and manufacturing, for a period of one year from
the date of sale. Other than this limited warranty, seller makes no express or implied warranties. Except for this limited warranty, NO EXPRESS OR
IMPLIED WARRANTIES ARE GIVEN AND NO AFFIRMATION OF SELLER, BY WORDS OR ACTION, WILL CONSTITUTE A WARRANTY. THE GOODS BEING
PURCHASED ARE BEING SOLD ON

A “WITH ALL FAULTS” BASIS. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE GOODS IS WITH THE
BUYER. SHOULD THE GOODS PROVE DEFECTIVE F OLLOWING THEIR PURCHASE, THE BUYER, AND NOT THE MANUFACTURER, DISTRIBUTOR OR RETAILER,
ASSUMES THE ENTIRE COST OF ALL NECESSARY INSTALLATION, SERVICING OR REPAIRS.

SMART CAREGIVER CORPORATION

1229 Nort h McDowell Blvd., Petaluma, CA. 94954 | Tel: [phone]
sales@smartca regivercorp.com | www.smartca regiver

corp.com

CordLess® Bed Sensor Pads

TEST THE SYSTEM

• Apply pressure to the pad to activate system. The Monitor will beep twice when
activated. The Pad 1 or Pad 2 light on the front of monitor will blink as long as
there is pressure on Pad 1 or Pad 2, respectively.

• The alert will sound whenever pressure is released from pad. Press the “Reset”
button on front of monitor or use the Caregiver Key, depending on your reset
setting to silence the alert.

• If the Pad Lost light is on and system does not test properly, reduce the

distance between the monitor and the pad. Retest.

BED PAD PLACEMENT

• Place the pad under shoulders to be alerted when the resident sits up in bed .

• Place pad under the hips/buttocks to be alerted when the resident vacates the bed

.

CordLess® Chair Sensor Pads

TEST THE SYSTEM

• Apply pressure to the pad to activate system. The Monitor will beep twice when
activated. The Pad 1 or Pad 2 light on the front of monitor will blink as long as
there is pressure on Pad 1 or Pad 2, respectively.

• The alert will sound when pressure is released from pad. Press the “Reset” button
on front of the monitor or use the Caregiver Key, depending on your reset setting to
silence the alert.

• If the Pad Lost light is on and system does not test properly, reduce distance
between the monitor and the pad. Retest.

WHEELCHAIR/CHAIR PAD PLACEMENT

• Center pad on the chair seat under buttocks.

C
o

r
d
L

e
s
s™

B
ed

Pa

d

C

o
rd
L

ess™

B
ed P

a
d

CordLess® Floor Mats

TEST THE SYSTEM

•

• Press the “Reset” button on the front of the monitor or use the Caregiver Key,

depending on your reset setting to silence the alert.
IMPORTANT: There must be a 15 second period with no pressure on the

NOTE:

• If the “Pad Lost” light is on and the system does not test properly, reduce the distance

FLOOR MAT PLACEMENT

•

plugged into the TL-2100G fall monitor. To reestablish wireless operation, unplug the corded device and test the Cordless device(s)
as described above.

Floor Mat

S
a
f
e
ty
A

u
t
o

-
R
e

s
e
t

T
M

P
a

d
a
n
d
M
o
n
i
t
o
r

A
c
ti
v

e
w
h
e
n
b
l
i
n
k
i
ng

L
o
w
Bat
te
r
y Pa

d
Lo
s
t

S
af

e
t
y
A
ut
o

-
R

e
s
e
t

T
M

P
ad a
nd
M
o
n
i
t
o
r

A
c
t
i
v
e
w
hen
b
l
i
n
k
in

g

L
o
w
Bat
t
e
r
y

P
ad
L
o
s
t

1

2

2012-13

TL-2100G

Fall Monitor

Installation and Use Instructions

PATENT ED TE CHNOLO GY

SM ART CAREG IVER CORPORAT ION

• No Cords Between Monitor and

Sensor Pads

• Works with two sensor pads

simultaneously

PATENTED TEC HNOLO GY

with included Caregiver Key

TM

IMPORTANT INFOR MATION:

Smart CordLess® products utilize wireless technology which is subjec t to physical and environmental
considerations. These products must be tested by the end user before each use in t he setting in
which they are to be used. Please be aware that the transmitter will not be 10 0% accurate if it is out of
range at any time. The transmi tter is battery operated and the life o f the battery will vary based on
usage. Wireless systems

and monitors are intended as an addition to good caregiving practices and are not

supervision of all residents by caregiver(s). We recommend that all personnel receive periodic training in the
operation of these systems and t hat the systems are tested before each use.

Reset

TL-2100G Rev.2

TL-2100G to fully reset.

TL-2100G and corded sensor pads/floor mats