Page 1
Mifare & ISO14443A-4 UID Slender Series Reader
Design & Technologies
Read both CSN and Sector of Mifare card and
FULL UID of Mifare Plus and DesFire card.
Economical mullion mounts type.
Support on-site Reader Configuration Card to
change certain parameters.
Design with customer logo is possible.
Door Bell function for Number pad reader.
Tamper protection
A PIN can be set inside the card to
authenticate with the reader so that “Card +
PIN” mode can be implemented without
Number pad use “touching sensor”, the latest
technology and individual number backlit when
touch.
Easily see under dark environment.
Could be use as a door location
Friendly Installation
“Touch” number pad does not
carry any moving parts, which
implies more durable.
All weather proof design with
IP65 certificate.
All inputs are 12Vdc
protected.
Universal back plate allows
the reader be installed on
different size of gang box.
Non-drop bottom screw made
servicing handier.
All input and output signals are
protected against static
charges.
Reverse power protection.
Stainless steel Security
screw is an option
Page 2
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled e nvironment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designe d to provide reasonable protection against harmful interference in a residential
installation. This equipment generates use s and can radiate radio freque ncy energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cau se h armful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Model Number: X1 X2 N1 N2 N3 – N4 X3
RF Technologies Reader Appearance and Function
3 = Normal Reader
N
1
5 = Normal Reader
N
2
X1X2
MW = Mifare + Mifare UID + DesFire UID
2 = Read UID / Card Number
N
3
3 = Reader Sector (HF Only)
8 = Pigtail
N
4
N = No Number pad; K = Number pad
X
3
Page 3
Model
Functions
Configurable Functions
Standard Reader Keypad Reader
Re-configure Window
Reader Output Format
Wiegand Plus Width
Keypad Output
Buzzer Control
LED/Back lit Control
Technical Specifications
Typical Read range
Reader Standard Ou tput
Standard Keypad output
Wiring Distance
Wiring Distance
Operating Specification::
Operating Voltage
Operating Current
Operating Temperature
Exterior dimension
Case material
Standard Color
Operating Humidity
Weight
5 seconds (Default) or Half an hour after Power up
CSN/UID 32bits, 34bits, 56bits (backward/forward), file content reading for programmed ID
Different choices to fit with different Controller’s requirements
N/A Definable
Reader & Controller control (Default) or Controller control only
Define different LED color response base on Green LED
>5 cm (Base on different technology)
Wiegand (RS232 & RS485 optional)
N/A Wiegand with 4 bits burst
150m (22 AWG with shielded cable)
13.56MHz； ISO14443A-4
10 - 15VDC
150mA (max)
-30℃-70℃
150*53*25 mm
PC+ABS
Black
10% - 90%
180g
Loading...