Page 1
Available Later! Standard Magic Available Later!Number pad Magic
)
125KHz & 13.56HMz Dual Frequencies Magic Series Reader
Design & Technologies
Read both low frequencies (125KHz) and high
frequencies card; supported high frequency
technologies are Legic, Mifare, Mifare Plus,
DesFire or FuDan CPU
Support on-site Reader Configuration Card to
change certain parameters.
Number pad use “touching sensor”, the latest
technology and individual number backlit when
touch.
Display Magic can provide customer a full
series of choices
Display reader can display CSN/UID number or
Programmed Card Number or user Name when
the user card is present.*
Languages)
Friendly Installation
.
(Supported Multiple
Tamper protection
Front plate customization and back lit design is
available.
Design with End User logo is possible.
Door Bell function for Number pad reader.
Economical Mini Magic can be mullion mount.
OLED Display allow user to see the message
clearly under direct sunlight.
APIN can be set inside the card to authenticate
with the reader so that “Card + PIN” mode can
be implemented without relying on the
controller.*
“Touch” number pad does not
carry any moving parts, which
implies more durable.
All weather proof design with
IP65 certificate.
Metal back plate allows the
reader install on metal surface
and back-to back without
affecting the read range.
Universal back plate allows
thereaderbeinstalledon
different size of gang box.
Non-drop bottom screw made
servicing handier.
All input and output signals are
protected against static
charges.
Reverse power protection.
Stainless steel Security
screw is an option
All inputs are 12Vdc
protected.
Page 2
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However , there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Model Number: X1X2N1N2N3–N4X
3
RF Technologies Reader Appearance and Function
N13 = Normal Reader ; 5 = Display Reader
2 = Normal Size
N
2
8=MiniSize
2 = Read UID / Card Number
N
3
3 = Read Sector (Mifare) / Segment (Legic)
3 = Terminal (for Display Reader)
N
4
8=Pigtail
X3N = No Number pad; K = Number pad
X1X
HM = Mifare & 125KHz Technologies
2
HL = Legic & 125KHz Technologies
Page 3
Model
Functions
Configurable Functions
Standard & Mini Reader Keypad Reader Display Reader
Re-configure Window
Reader Output Format
Wiegand Plus Width
Keypad Output
Buzzer Control
LED/Back lit Control
Display Clock
Synchronization.
Technical Specifications
Typical Read range
Reader Standard Output
Standard Keypad output
Display
Display Message
Wiring Distance
5 seconds (Default) or Half an hour after Power up
CSN/UID 32bits, 34bits, 56bits (backward/forward), file content reading for programmed ID
Different choices to fit with different Controller’s requirements
N/A Definable Definable
Reader & Controller control (Default) or Controller control only
Define different LED color resp onse base on Green LED N/A
N/A N/A
3–5cm
Wiegand (RS232 & RS485 optional)
N/A Wiegand with 4 bits burst Wiegand with 4 bits burst
N/A N/A OLED Display
N/A N/A
150m (22 AWG with shielded cable) 120m (22 AWG with shielded cable)
H/W reset
Via RS485 TimeSyn S/W
Access Granted, Access
Denied, Enter PIN;
Time;
Card Number
Operating Specification:
Operating Voltage
Operating Current
Operating Temperature
Exterior dimension (Mini) 11 5.5*84.5*20.5mm (84.05*54.05*16.5mm)
Case material
Standard Color
Operating Humidity
Weight (Mini)
10 - 15VDC
150mA (max)
-30℃-70℃
PC+ABS
Black
10% - 90%
210g (160g)
Loading...