Page 1
Available Later! Standard Magic Available Later!Number pad Magic
Design & Technologies
DesFire EV1 Magic Series Reader
Read full 56 bits UID, Application & Files
content of DesFire EV1 card.
Support 3DES & AES encrypted
communication between the reader and card.
Support on-site Reader Configuration Card to
change certain parameters.
Number pad use “touching sensor”, the latest
technology and individual number backlit when
touch.
Display Magic can provide customer a full
series of choices
Display reader can display CSN/UID number or
Programmed Card Number or user Name when
the user card is present.*
Languages)
Friendly Installation
(Supported Multiple
Tamper protection
Front plate customization and back lit design is
available.
Design with End User logo is possible.
Door Bell function for Number pad reader.
Economical Mini Magic can be mullion mount.
OLED Display allow user to see the message
clearly under direct sunlight.
APINcanbesetinsidethecardtoauthenticate
with the reader so that “Card + PIN” mode can
be implemented without relying on the
controller.*
“Touch” number pad does not
carry any moving parts, which
implies more durable.
All weather proof design with
IP65 certificate.
Metal back plate allows the
reader install on metal surface
and back-to back without
affecting the read range.
Universal back plate allows
the reader be installed on
different size of gang box.
Non-drop bottom screw made
servicing handier.
All input and output signals are
protected against static
charges.
Reverse power protection.
Stainless steel Security
screw is an option
All inputs are 12Vdc
protected.
Page 2
Model Number: X1X2N1N2N3–N4X
3
RF Technologies Reader Appearance and Function
N13 = Normal Reader ; 5 = Display Reader
2 = Normal Size
N
2
8=MiniSize
X1X2MD = DesFire Technology
Model
Functions
Configurable Functions
Re-configure Window
Reader Output Format
Wiegand Plus Width
Keypad Output
Buzzer Control
LED/Back lit Control
Display Clock
Synchronization.
Technical Specifications
2 = Read UID / Card Number
N
3
3 = Sector reading (Only Mifare)
3 = Terminal (for Display Reader)
N
4
8 = Pigtail
X3N = No Number pad; K = Number pad
Standard & Mini Reader Keypad Reader Display Reader
5 seconds (Default) or Half an hour after Power up
CSN/UID 32bits, 34bits, 56bits (backward/forward), file content reading for programmed ID
Different choices to fit with different Controller’s requirements
N/A Definable Definable
Reader & Controller control (Default) or Controller control only
Define different LED color response base on Green LED N/A
N/A N/A
H/W reset
Via RS485 TimeSyn S/W
Typ ical R ead r a n ge
Reader Standard Output
Standard Keypad output
Display
Display Message
Wiring Distance
Wiegand (RS232 & RS485 optional)
N/A Wiegand with 4 bits burst Wiegand with 4 bits burst
N/A N/A OLED Display
N/A N/A
150m (22 AWG with shielded cable) 120m (22 AWG with shielded cable)
2–3cm
Access Granted, Access
Denied, Enter PIN;
Time;
Card Number
Operating Specification:
Operating Voltage
Operating Current
Operating Temperature
Exterior dimension (Mini) 115.5*84.5*20.5mm (84.05*54.05*16.5mm)
Case material
Standard Color
Operating Humidity
Weight (Mini)
10 - 15VDC
150mA (max)
-30℃-70℃
PC+ABS
Black
10% - 90%
210g (160g)
Page 3
FCC Caution.
§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Loading...