Manual
Bluetooth & Multi-technologies Reader User Manual
Mounting:
1. Install t he metal plate o n the wal l with two or four scr ews, which dep ends on d ifferent ki nds of
gang box being installed
2. The cover shall clip on the upper edge
.
the push in the bottom part as show in
Rec
ommendation:
1. Linear DC Power Supply;
2. 22AW G s hield ed cable; it’s required to do “ one-point” ground. (As shown in the diagram)
diagram
3. Tigh
reader and the back plate
.
ten the secure non-dropout screw, which lo cated underneath of the reader to fix the
Specification:
, installation is completed.
Wirin
g:
Color Description
Red Power Supply to the reader
Black Signal GND
Green Wiegand Output data, D0
Input Voltage (at
Reader end)
Operating Current
Operating
Temperature
DC9V~15V
160mA (max)
-30ºC~70 ºC
Typical Read
range
Maximum Cable
Length
Num ber pad
format
2~ 5cm
150m
4 bits bur s t by default
White Wiegand Output data, D1
Yellow RED LED control, active l o w.
Blue Green LED control, active low
Brown Buzzer input, active low
Orange Tamper output (open collector, Active low, max 100mA)
Purple
Door bell output (open collector, +5Vdc output ≤ 5mA)
Manual
Discount the power and confirm that the power supply cable is
he shield cable is correctly connected to Classis Ground at
Check if data 0 & data 1 cable is correctly connected (See “Wiring”
Bluetooth & Multi-technologies Reader User Manual
Power up Sequences:
1. When reader is powered up, the Green back will fli ck er fo r 5 sec on ds. T he rea der wil l beep
once , then about 2 seconds later , the reader will beep once and the reader is in Ready
mode.
2. Present the card. The Blue LED will flicker once; buzzer will beep onc e.
3. Pres en t t h e mobile phone ,after Yellow LED and Burgundy LED come on , the Blue LED will
flicker once ; buzzer will beep once .
4. When card is present and read by the reader, blue back lit will flash once; and buzzer will
beep once a s well. The card data w i ll th en tran smit t o the controller. After, weather the back lit
of the reader will remain ON or Flash or change to Green or Red color, this shall depend on
the G reen and Red LED inputs.
5. For number pad reader, when a number is pressed and successfully detected, the back lit
under the number will flash 1 time an d th e b uz zer wi l l b eep onc e. T h e num ber b ei n g pr es s ed
will burst out by default (4 bits burst).
Physical Dimension:
Troubleshooting:
Trouble List Solution
No Response
when Power Up
Auto Rest art
Cannot read card
number correctly
Reader beeps but
No card data info
Buzzer error Check if the buzz er cable is correctly connecte d (Se e “Wiring” above).
Bac k Lit Error
Keypad
No Response
correct ly co nnected (See “Wiring” above).
Check the input voltage is sufficient (See “Specifications” above).
Check the input voltage is sufficient (See “Specifications” above).
Chec k the format s etti ng on t he co ntroller i f it is th e same as the card
format. Use approved card (known format and Facility Code) to test.
Check if t
ONE point o nly.
above).
Check the input voltage at the card reader end is correct (See
“Specifications” above).
Chec k the Led ca ble is correctly connec ted (See “Wiring” above).
Use Default Config urati on Car d to set it back to norm al.
Power off reader for 5 seconds and power on again
FCC Statement：
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference,and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Loading...