Smanos MD9260 User manual [ml]

2015 SMANOS HOLDING LTD. All Rights Reserved.

©

Printed in China
Ver: MD9260-UM-EN/DE/FR/NL-V1.0

MULTILINGUAL

EN DE FR NL

USER MANUAL

MD9260

Solar-Powered Dual-Tech

Motion Detector

EN EN

Introduction

MD9260 is a solar-powered motion detector utilizing a single
passive infrared element and microwave technology. It consists of
digital dual-core fuzzy logic infrared control chip and intelligent
analysis which could effectively identify interference signals from
body movement signals so as to reduce false alarms. The detector
is battery powered and kept re-charging by the solar panel to
save energy. Unique housing material and structure improve its
waterproof level for outdoor use. Only after being connected
successfully with alarm system, the detector can work normally.

Features

1. Accurate detection

■

It has microwave and infrared dual detections to prevent false
alarms.

■

It consists of digital dual-core fuzzy logic infrared control chip and
intelligent analysis which could effectively identify interference
signals from body movement signals.

■

With automatic temperature compensation and anti-air turbulence
technology, it easily adapts to environmental changes.

2. Outdoor use

It adopts ABS and anti-UV materials for outdoor use with IP65
rating.

3. Energy saving

■

Rechargeable by solar power.

■

Energy saving mode to reduce battery charging times, and
extending battery life.

Product Overview

Solar Panel

Fixing Screw

LED Indicator

Detection Lens

Base

Detector Installation Bracket

LED Indication

LED Status Meaning

Red and orange LEDs ash

continuously for 1 min

Red LED ashes once Infrared is triggered
Orange LED ashes once Microwave is triggered

Red and orange LEDs ash once

at the same time

Red LED ash 3 times every

12 seconds

Self-testing

Both infrared and microwave
are triggered, the detector
sends alarm signal.
Low battery. Please install on

place with sufcient sunlight

Attachment

Bracket

EN EN

m

0m

PCB Layout

④

①

LED On/Off

②

Working Mode

Setting

③

Battery

3.7V 186 50

1. LED options: ON/OFF (default setting is ON).

2. Working mode options: 10S=Test mode, 5MIN=Power saving mode
(default setting is test mode).

3. Battery: One piece of 18650 rechargeable lithium battery.

4. Microwave sensitivity adjustment options: HIGH, MEDIUM, LOW.
(default setting is medium).

5. Tamper switch: In working state, if the housing is opened, detector
will send alarm signal.

6. Zone mode options: Normal zone, home zone, 24-H zone (default
setting is normal zone).

Normal zone: In arm or home arm state, the detector set at normal

zone will trigger an alarm once intrusion is detected.

Home zone: In home arm state, the detector set at home zone is

disarmed.

24-H zone: The detector set at 24-H zone will trigger an alarm once

intrusion is detected, no matter the system is armed or disarmed.

Microwave Sensitive Adjustment

⑤

Tamper Switch

⑥

Zone Mode Setting

Detection Scope

110°

Top view

0m

2m

2m

Side view

4m

6m 8

Working Mode Selection

After the battery is loaded, the detector enters into 1 min self-

testing with the red and orange LEDs ashing continuously, and

then it starts to work according to the pre-set working mode.

5 MIN

10 S

Testing Mode Power Saving Mode

Testing mode (default setting): The detector detects once every

10 seconds.

5 MIN

10 S

EN EN

Power saving mode: The detector enters a 5-minute testing mode

rstly, and then switches to power saving mode. If the detector

detects movements twice in 5 minutes, it automatically goes into
asleep state. If there is no movement detected in next 5 minutes, it
will switch from asleep state to arm. As long as there is a movement
detected within 5 minutes, the duration of power saving mode will
be extended.

Note: It is suggested to set the detector in power saving mode for daily use to save power.

Test

Remove the battery activation strip. After red and orange LED

ash continuously for 1 min, it enters working state. By then, put

the detector on a shelf, walks from the left to right (or right to left)
within the detection scope to trigger it, red and orange LEDs will

ash once. This indicates the detector is working properly.

Installation & Notices

Installation steps:

1. Make the attachment bracket and base apart.

2. Fix the base on the right place (see notices).

3. Tighten the attachment bracket with the detector.

4. Tighten the attachment bracket with the base and adjust to proper
detecting angle.

Notices:

1. It is recommended to mount the detector at height of 2 m from the
ground.

2. The detector is more sensitive to cross movement than vertical
movement, so it is suggested to mount it facing vertical to the
walking direction of people.

3. Please avoid putting big objects in front of the detector which will

inuence the detection.

4. Please avoid any cases that pets can climb over to avoid false
alarms.

5. As it is a solar-powered detector, please install it where adequate
sunlight is ensured.

EN EN

Solar panel output current: 2000LX illumination ≥ 4 mA
Battery standby time: <180 days
Detection scope: 8 m/110°
Wireless transmitting distance: < 80 m (in open area)

Ground

Radio frequency: 868 MHz or 915 MHz
Operating condition:

Temperature: -10°C ~ + 55°C
Relative humidity: < 80% (non-condensing)

Housing material: PC+ABS+ANTI-UV
Detector dimensions (L x W x H): 186 x 200 x 125 mm
Bracket dimensions (L x W x H): 75 x 72 x 155 mm

Connect to Control Panel

Make sure the control panel is in pairing state, trigger the detector
to alarm until the panel gives out a beep, which indicates the
connection succeeded. Arm the system, trigger the detector

again, and the siren of control panel will hoot to conrm that the

connection is successful.

Specications

Power supply:

18650 3.7 V 1800 mAh rechargeable lithium battery

Standby current: < 0.16 mA

DE DE

Einleitung

MD9260 ist eine solarbetriebener Bewegungsmelder mit einem
einzigen Passiv-Infrarot-Element und Mikrowellentechnologie. Er
besteht aus einem Infrarot-Steuerchip mit digitaler Dual-Core­Fuzzy-Logik und intelligenter Analyse zur effektiven Unterscheidung
von Störsignalen und Signalen der Körperbewegung, um
Fehlalarme zu reduzieren. Der Melder ist akkubetrieben und wird
vom Solarmodul wiederaufgeladen, um Energie zu sparen. Das
einzigartige Gehäusematerial und die Struktur verbessern seine
Wasserdichtheit für den Einsatz im Außenbereich. Nur nach der
erfolgreichen Verbindung mit dem Alarmsystem kann der Melder
normal arbeiten.

Merkmale

1. Präzise Erkennung

■

Er verfügt über duale Erfassung mit Mikrowellen und Infrarot, um
Fehlalarme zu vermeiden.

■

Er besteht aus einem Infrarot-Steuerchip mit digitaler Dual-Core­Fuzzy-Logik und intelligenter Analyse zur effektiven Unterscheidung
von Störsignalen und Signalen der Körperbewegung.

■

Mit automatischer Temperaturkompensation und Anti­Verwirbelungstechnologie passt er sich leicht an Veränderungen der
Umwelt an.

2. Einsatz im Außenbereich

Er verwendet ABS und Anti-UV-Materialien für den Einsatz im
Außenbereich mit Schutzklasse IP65.

3. Energiesparen

■

Wiederauadbar mit Solarstrom.

■

Energiesparmodus, um die Akkuladezeit zu reduzieren und die
Akkulebensdauer zu verlängern.

Produktübersicht

Solarmodul

Befestigungsschraube

Befestigungs-

LED-Anzeige

Erkennungsobjektiv

Fußplatte

Melder Montagehalterung

LED-Anzeige

LED-Status Bedeutung

Rote und orange LED blinken
kontinuierlich 1 Minute lang

Rote LED blinkt einmal Infrarot wird ausgelöst
Orange LED blinkt einmal Mikrowelle wird ausgelöst

Rote und orange LED blinken
einmal zur gleichen Zeit

Rote LED blinkt 3 Mal alle
12 Sekunden

Selbsttest

Infrarot und Mikrowelle wurden
ausgelöst, der Melder sendet
ein Alarmsignal.

Schwache Batterien. Bitte an
einem Platz mit ausreichender
Sonneneinstrahlung montieren

winkel