SLX 28031R User Manual
28031R
Flat TV Screen Wall Mount 14 - 32” - Flat to Wall
Main Features
USER GUIDE
• TV Size Range: 14-32’’
• Maximum Weight Capacity: 30kg
• Mount Function: Flat to Wall
• Wall to TV Distance:19mm
• Compatible with VESA Sizes: 75x75/100x100/200x100/200x200
• 200x200 Max. Hole Pattern
•
We have not supplied wall xings with this product. All walls dier in strength
and thickness. Consult a qualied installer or seek advice from your local
DIY/hardware store on purchasing suitable wall xings to safely mount the
bracket on the type of wall being used.
•
Check the contents list and images below to check there are no missing or
defective parts.
•
Never exceed the Maximum Weight Capacity shown above.
•
Read these instructions carefully before installation. If in any doubt about
safely installing this product, contact a professional installer for assistance.
•
This product was designed to be installed on wood stud walls and solid
concrete/brick walls. When xing to walls screws/bolts should be xed into
bricks/stone not into mortar courses.
•
Make sure the wall will support the combined load of the
equipment and hardware.
Also check for hidden wiring or plumbing.
•
Make sure that the heads of the screws/bolts you buy as wall fastenings are
the correct size to hold the bracket securely in position.
•
For larger/heavier TVs we recommend that you ask someone to assist you
with lifting and positioning your TV.
•
This product is suitable for indoor use only.
•
Improper installation or use of this product can result in product failure,
damage or personal injury.
•
This product contains small items that could cause choking if swallowed, so
keep these items away from children and pets.
•
Appropriate safety equipment and proper tools must be used for installation.
Always check manufacturer’s operating and safety instructions before using
tools and other equipment
WARNING
Components
Wall Mount & VESA Compatibility
• VESA is the standard adopted by most TV manufacturers for wall
bracket mounting.
• There are 4 holes on the back of every at screen TV and the
space between the holes is governed by the VESA standard.
• VESA comes in a range of sizes depending on the weight and size
of the at screen TV; sizes 50 x 50mm, 75 x 75mm, 100 x 100mm,
100 x 200mm and so on... are standard. Not all at screen TVs are
compliant, contact the TV manufacturer for assistance if your TV
does not appear to comply with VESA.
• To check if your TV or monitor is compliant, look at the rear of
the display there should be 4 screw-holes in a square pattern or
in larger displays a rectangular shape. See Fig. 2 opposite, with
VESA mounting points shown in white circles.
• Measure the distances marked (2) (horizontal) x (1) (vertical) in
mm to nd your VESA format.
Fig. 2
Before installation check that you have all the components shown here and that none of them is damaged.
Fig. 1
ID Qty Description
A1
4 M4×12mm bolt
A2
4 M5×12mm bolt
A3
4 M6×12mm bolt
A4
4 M8×16mm bolt
A5
4 M5 Washer
C1
4 M4×25mm bolt
C2
4 M5×25mm bolt
C3
4 M6×25mm bolt
C4
4 M8×25mm bolt
C5
4 Spacer
Page 1
2
3
ID Qty Description
1
1 Wall Plate
2
1 Adaptor Bracket
3
2 Safety Bolt
1
A1
A2
A3
A4
A5
C1
C2
C3
C4
C5
Page 2
Mounting your TV - Overview
Once you have decided where to locate your TV and where the bracket
needs to be positioned, mounting requires the 3 steps described below.
Step 1: mark and drill xing holes in the wall and attach the Wall Plate
1
to the wall using suitable screws/bolts.
Step 2: attach the Adaptor Bracket
2
& to the back of the TV using the
plastic spacers
C5
if required.
Step 3: slide the Adaptor Bracket
2
with the TV attached onto the Wall
Plate 1 and make secure using the Safety Bolts 3. You may nd it easiest
to make your connections before this Step.
STEP 1 - Fixing the Wall Plate to the Wall
Fixing to Concrete/Brick Walls
The process is similar to to attaching the Wall Plate 1 to wood.
You should use a minimum of 3 screws/bolts, washers and wall plugs
suitable for the type of wall you are mounting onto (if in doubt ask for
advice at your local DIY/hardware store and remember to make sure that
washers and the heads of the screws/bolts are the correct size to hold
Fixing to Wood (Stud Walls)
Use a stud sensor to locate the upright stud closest to where you want to
mount your screen (the centres of each stud are usually approx. 400mm
or 600mm apart). It is a good idea to verify where the studs are located
with an awl or thin nail.
The Wall Plate 1 is attached to the wall using a minimum of three
appropriate screws/bolts and washers as shown in Fig. 4.
Make sure the screws/bolts are suitable for wood and large enough to
support the weight of the TV and bracket (if in doubt ask for advice at
Fig. 3 Fig. 4
your local DIY/hardware store and remember to make sure that washers
and the heads of the screws/bolts are the correct size to hold the bracket
securely in position).
Mark and drill your rst hole into the wood as close as possible to the
centre of an upright. To mark the remaining hole/holes, hold the Wall
Plate 1 to the wall, use a spirit level (not supplied) to make sure the
bracket is level, and mark the centre of each hole. Make sure the Wall
Plate is oriented as shown below and all screws/bolts are fully tightened.
the bracket securely in position), see Fig. 5. When xing to walls screws/
bolts should be xed into bricks/stone not into mortar courses. Use the
Wall Plate
1
as a template to mark screw/bolt positions and make sure all
screws/bolts are properly tightened.
Fig. 5 Fig. 6
1
1
1
1
Page 3
STEP 2 - Attaching the Adaptor Bracket to the TV
Determine the proper VESA mounting conguration for your screen, see
Fig 2. Four each of two lengths of M4, M5, M6 and M8 mounting bolts
are provided for attaching the Adaptor Bracket 2 to the VESA mounting
holes use
the size which ts your TV. Use longer length bolts C1....
C4
and
the four Plastic Spacers
C5
f
or TV’s with curved or recessed back panels as
shown in Fig 7.
If you are mounting to a television with a at back you can use shorter
bolts
A1
....
A4
and will not need a plastic spacer
C5
, see Fig 8. For M4 and
M5 bolts use the M5 washers
A5
.
Make sure all four bolts are properly tightened and held in place by at
least three full turns. Do not overtighten.
Fig.7
STEP 3 - Attaching Adaptor Bracket to the Wall Plate
Attach Adaptor Bracket
2
to Wall Plate
1
by sliding the anges of the
Adaptor Bracket
2
into the anges of the Wall Plate
1
.
Secure with the two safety bolts 3. Tighten bolts securely.
Do not overtighten
3
Fig.9
2
2
Fig.8
2
1
NOTE: The centres of studs are normally
approx. 400mm - 600mm apart.
A1A2A3 A4
A5
C1C2C3
C4
C5
A5
Loading...