Sloan REGAL 110 XL, REGAL 111 XL, REGAL 116 XL, REGAL 120 XL, REGAL 122 XL Installation Instructions Manual

Code No. 0816312

Rev. 1 (05/10)

I

INSTALLATION INSTRUCTIONS FOR EXPOSED REGAL®XL

WATER CLOSET AND URINAL FLUSHOMETERS

LIMITED WARRANTY

Sloan Valve Company warrants its Regal XL Flushometers to be made of first class materials, free from defects of material or workmanship under normal use and
to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1
year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be
thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for
labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from
Sloan Valve Company for purpose of resale.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY RESPONSIBLE FOR
ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

Before you install the Regal XL Flushometer, be sure the items listed
below are installed. Also, refer to the rough-in diagrams on the next page.

• Closet or urinal fixture

• Drain line

• Water supply line

Important:

•

I

NSTALL ALL PLUMBING IN ACCORDANCE WITH APPLICABLE CODES

AND REGULATIONS.

•

WATER SUPPLY LINES MUST BE SIZED TO PROVIDE AN ADEQUATE
VOLUME OF WATER FOR EACH FIXTURE.

•

FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

The Sloan Regal XL Flushometer is designed to operate with 10 to 100
psi (69 to 689 kPa) of water pressure.

THE MINIMUM PRESSURE
REQUIRED TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE
SELECTED.

Consult fixture manufacturer for minimum pressure
requirements. Most Low Consumption water closets (1.6 gpf/6.0 Lpf)
require a minimum flowing pressure of 25 psi (172 kPa).

Closet Flushometer
1½” (38 mm) Top Spud

MODELS 110/111,
113, 115 & 116

Closet Flushometer
1½” (38 mm) Back Spud

MODEL 120 & 122

Service Sink Flushometer
1½” (38 mm) Top Spud

MODEL 117

Urinal Flushometer
1¼” (32 mm) Top Spud

MODEL 180

Urinal Flushometer
¾” (19 mm) Top Spud

MODEL 186

Squat Toilet Flushometer
1½” (38 mm) Back Spud

MODEL 137

PRIOR TO INSTALLATION

TOOLS REQUIRED FOR INSTALLATION

• Straight blade screwdriver

• Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth jawed spud wrench

2

†

†

†

†

†

M

MODELS 110/111

MODELS 113, 115 & 116

MODEL 117 MODELS 120/122

MODEL 180 MODEL 186

NOTE: Model 180
requires 1” I.P.S.
(DN 25 mm) Supply

IMPORTANT NOTES:

• When mounted on an ADA accessible bowl, the rough-in to the supply inlet should be no higher than 37½” or the handle will exceed maximum height allowances under ADA guidelines.

• New ADAAG Guidelines allow for Split or Offset Grab Bars, check with local authorities or reference section 604.5.2 of ADAAG.

† 1” Control Stop is available with Whitworth Thread

NOTE: Water Closet
Valves with “-2.4”
Model Designation
deliver 2.4 gpf (9.0 Lpf)

VALVE ROUGH-INS