Sloan 8110, 8111, 8113, 8115, 8116 Install Instructions

Download

Page 1

Code No. 0816805

Rev. 4 (01/12)

INSTALLATION INSTRUCTIONS FOR RETROFIT AND COMPLETE VALVE

INSTALLATION FOR SLOAN SOLIS

, SOLAR POWERED, SINGLE FLUSH

WATER CLOSETS AND URINALS

RESS Series Retroﬁt Conversion Kit Models

RESS Sloan SOLIS® Models are used to convert existing Flushometers to

Solar Powered, Sensor Activated.

Sloan SOLIS® Water Closet Models can be furnished for the following:

8100 Series Complete Flushometer Models

8100 Series Sloan SOLIS® valves are complete flushometers

and ideal for new installations.

1.6 gpf/6.0 Lpf For Low Consumption Bowls

3.5 gpf/13.2 Lpf For Water Saver Bowls

Sloan SOLIS® Urinal Models can be furnished for the following:

1.0 gpf/3.8 Lpf For Low Consumption Urinals

1.5 gpf/5.7 Lpf For older Siphon Jet Urinals

LIMITED WARRANTY

Unless otherwise noted, Sloan Valve Company warrants this product, manufactured and sold for commercial or industrial uses, to be free from defects in material and workmanship for a period of three (3) years (one (1) year for special finishes, SF faucets, PWT electronics and 30 days for PWT software) from date of first purchase. During this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any product which fails to conform with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY

RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.

PRIOR TO INSTALLING THE SLOAN SOLIS® FLUSHOMETER

Prior to installing the Sloan SOLIS® flushometer, install the items listed below as illustrated in the rough-in diagram. (New installations only.)

• ClosetorUrinalfixture

• Drainline

• Watersupplyline

IMPORTANT:

• INSTALLALLPLUMBINGINACCORDANCEWITH

APPLICABLE CODES AND REGULATIONS.

• WATERSUPPLYLINESMUSTBESIZEDTOPROVIDEAN

ADEQUATE VOLUME OF WATER FOR EACH FIXTURE.

• WHEN INSTALLING A FLUSHOMETER, IT IS IMPORTANT THAT THE FLUSH MODEL MATCHES THE REQUIREMENTS OF THE PLUMBING FIXTURE.

• FLUSH ALL WATER LINES PRIOR TO MAKING CONNECTIONS.

The Sloan SOLIS® is designed to operate with 15 to 100 PSI (104 to 689 kPa) of water pressure.

TO THE VALVE IS DETERMINED BY THE TYPE OF FIXTURE SELECTED.

Consult fixture manufacturer for pressure requirements.

THE MINIMUM PRESSURE REQUIRED

Most Low Consumption water closets (1.6 gallon/6 liter) require a minimum flowing pressure of 25 psi (172 kPa).

TOOLS REQUIRED FOR INSTALLATION

• Slottedscrewdrivertoadjustcontrolstop.

• SloanA-50Super-Wrench™,SloanA-109PlierWrenchorsmoothjawed

spud wrench for couplings.

• Trimpotadjustmentscrewdriver(supplied)toadjustrange,ifnecessary.

• Strapwrench(supplied)toinstallSloanSOLIS® to valve body.

• 7/64”hexwrench(supplied)tosecureSloanSOLIS

cover to base plate.

• 5/64”hexwrenchtosecurewaterSupplyFlange.

Page 2

VALVE ROUGH-IN

Water Closet Installation

Model 8110/8111, 8113, 8115, and 8116

Reference for RESS-C Retrofit

2¼”(57mm)MIN.

“Y”

“X”

C/L OF WASTE

FINISHED

WALL

Model “X” “Y”

8111†11½”(292mm) 16½”(419mm)

8113 16”(406mm) 21”(533mm)

‡

8115

8116

24”(610mm) 29”(737mm)

‡

27”(686mm) 32”(813mm)

C/L OF

FIXTURE

FINISHED

FLOOR

1”I.P.S.

(25 mm DN)

SUPPLY

4¾”

(121 mm)

Typical Urinal Installation

Models 8180 & 8186

Reference for RESS-U Retrofit

2¼”(57mm)MIN.

16½”

11½”

(292 mm)

FINISHED

WALL

(419 mm)

C/L OF

FIXTURE

FINISHED

FLOOR

8180

1”I.P.S.

(25 mm DN)

SUPPLY

8186

¾”I.P.S.

(20 mm DN)

SUPPLY

4¾”

(121 mm)

When installing the Sloan SOLIS® in a handicap stall: Per the ADA Guidelines (section 604.9.4) it is recommended that the grab bars be split or shifted to the wide side of the stall.

†

For new installations, Sloan strongly recommends the use of our Model 8111

which has a shorter installation height.

‡

Model 8115 & 8116 valves are designed for installations where the water supply

isroughed-in24”-27”(610mm-686mm)abovethetopofthewatercloset.

!!! IMPORTANT !!!

NEVER OPEN CONTROL STOP TO WHERE THE FLOW

FROM THE VALVE EXCEEDS THE FLOW CAPABILITY

OF THE FIXTURE. IN THE EVENT OF A VALVE FAILURE,

THE FIXTURE MUST BE ABLE TO ACCOMMODATE A

CONTINUOUS FLOW FROM THE VALVE.

!!! IMPORTANT !!!

PROTECT THE CHROME OR SPECIAL FINISH

OF FLUSHOMETERS — DO NOT USE TOOTHED

TOOLS TO INSTALL OR SERVICE THESE VALVES.

USE A SLOAN A-50 SUPER-WRENCH™, SLOAN

A-109 PLIER WRENCH OR SMOOTH JAWED SPUD

WRENCH TO SECURE ALL COUPLINGS.

ALSO SEE “CARE AND CLEANING” SECTION.

!!! IMPORTANT !!!

LAWS AND REGULATIONS PROHIBIT THE

USE OF HIGHER FLUSHING VOLUMES THAN

LISTED ON FIXTURE OR FLUSHOMETER.

!!! IMPORTANT !!!

THE STRAP WRENCH PROVIDED WITH THE SOLIS® IS

A CONVENIENCE TOOL AND IS NOT TO BE USED TO

REMOVE OR INSTALL THE FLUSHOMETER COUPLINGS.

USE STRAP WRENCH ONLY TO INSTALL THE SOLIS

LOCKING RING.

!!! IMPORTANT !!!

WITH THE EXCEPTION OF THE CONTROL STOP INLET,

DO NOT USE PIPE SEALANT OR PLUMBING GREASE ON

ANY VALVE COMPONENT OR COUPLING!

!!! IMPORTANT !!!

THIS PRODUCT CONTAINS MECHANICAL AND/OR

ELECTRICAL COMPONENTS THAT ARE SUBJECT TO

NORMAL WEAR. THESE COMPOENTS SHOULD BE CHECKED ON A REGULAR BASIS AND REPLACED AS NEEDED TO MAINTAIN THE VALVE’S PERFORMANCE.

Please take the time to read this manual to ensure proper

product installation and longevity. Also, please visit our

website to download our most recent documentation for this

product.

If you have questions about how to install your Sloan

flushometer, consult your local Sloan Representative or call

Sloan Technical Support Team at:

1-888-SLOAN-14 (1-888-756-2614)

Page 3

1 - FOR COMPLETE VALVE INSTALLATION, START HERE. FOR RESS RETROFIT INSTALLATIONS, START AT STEP 6. INSTALL OPTIONAL SWEAT SOLDER ADAPTER (ONLY IF YOUR SUPPLY PIPE DOES NOT HAVE A MALE THREAD)

MeasurefromfinishedwalltoC/LofFixtureSpud.Cutpipe1¼”

FINISHED WALL

(32 mm) shorter than this measurement. Chamfer O.D. and I.D. of water supply pipe.

Slide Threaded Adapter fully onto pipe.

Sweat solder the Adapter to pipe.

!!! IMPORTANT !!!

WITH THE EXCEPTION OF THE CONTROL STOP INLET,

DO NOT USE PIPE SEALANT OR PLUMBING GREASE ON

ANY VALVE COMPONENT OR COUPLING!

WATER SUPPLY PIPE

1-1/4”

(32 mm)

SWEAT SOLDER ADAPTER

C/L OF

FIXTURE

SPUD

2 - INSTALL COVER TUBE, WALL FLANGE AND CONTROL STOP TO SUPPLY PIPE

Measure from finished

wall to first thread of adapter or threaded supply pipe (dimension

“X”).Cutcovertubeto

this length.

Slide cover tube over pipe.

Slide wall flange over cover tube until against wall.

WATER

SUPPLY PIPE

“X”

SWEAT SOLDER ADAPTER

COVER TUBE

WALL FLANGE

Thread control stop onto

pipe. Tighten with a wrench.

SET SCREW

SUPPLY FLANGE

Tightensetscrewwitha5/64”

hex wrench. DO NOT install vandal resistant stop cap at this time.

IRON PIPE NIPPLE OR COPPER PIPE WITH SWEAT SOLDER ADAPTER

COVER TUBE

BAK-CHEK CONTROL STOP

3 - FLUSH OUT SUPPLY LINE

Open Control Stop.

Turn on water supply to flush line of any debris or sediment.

Close control stop.

4 - INSTALL VACUUM BREAKER FLUSH CONNECTION

NOTE

If cutting Vacuum Breaker Tube to size, note that Critical Line (C/L) on

VacuumBreakermusttypicallybe6”(152mm)abovefixture.Consult

Code for details.

Slide Spud Coupling, Nylon Slip Gasket, Rubber Gasket and Spud

Flange over Vacuum Breaker Tube.

Insert Tube into Fixture Spud.

Hand tighten Spud Coupling onto Fixture Spud.

MODELS 8110/8111, 8115, 8116

VACUUM

BREAKER

TUBE

SPUD COUPLING

NYLON SLIP

GASKET

RUBBER GASKET

SPUD FLANGE

MODEL 8180 MODEL 8186

VACUUM

BREAKER

TUBE

SPUD COUPLING

NYLON SLIP

GASKET

RUBBER GASKET

SPUD FLANGE

Page 4

5 - INSTALL FLUSHOMETER

Lubricate tailpiece o-ring with water.

Insertadjustabletailpieceintocontrol

stop. Tighten tailpiece coupling by hand.

Align flushometer directly above the

vacuum breaker flush connection by sliding the flushometer body IN or OUT as needed. Tighten vacuum breaker coupling by hand.

Align flushometer body and securely tighten first the tailpiece

coupling (1), then the vacuum breaker coupling (2), and finally the spud coupling (3). Use a wrench to tighten these couplings in the order shown.

NOTE

MaximumadjustmentoftheSloanAdjustableTailpieceis½”(13mm)

INorOUTfromthestandard4¾”(121mm)(centerlineofFlushometer

to centerline of Control Stop).

Ifroughing-inmeasurementexceeds5¼”(133mm),consultfactory

for longer tailpiece.

FLUSHOMETER

BODY

G-44 FRICTION RING

VACUUM

BREAKER

COUPLING

VACUUM BREAKER

FLUSH CONNECTION

SPUD

COUPLING

C/L

FIXTURE

ADJUSTABLE

(121 mm)

TAILPIECE COUPLING

O-RING

TAILPIECE

VACUUM BREAKER REPAIR KIT

4-3/4”

CONTROL STOP

C/L

SUPPLY

6 - WHEN RETROFITTING AN EXISTING VALVE, START HERE. REMOVE COMPENENTS FROM EXISTING FLUSHOMETER (RESS RETROFIT INSTALLATIONS ONLY)

Remove control stop cap.

Turn off water supply at control stop. Push valve handle to relieve

water pressure.

Remove outside and inside covers and old inside parts kit.

Remove old handle assembly and gasket.

Install chrome handle cap with gasket to handle opening on

flushometer body. Tighten chrome handle cap securely.

NOTE: An extra H-533 tail o-ring is included in the event leakage occurs if the valve is repositioned during the installation of the new SOLIS®. Use only as needed.

INSTALLATIONS ONLY

TAIL O-RING

RESS SERIES

7 - SLOAN SOLIS® FLUSH VOLUME (RESS RETROFIT INSTALLATIONS ONLY)

The flush volume of the Sloan SOLIS® is controlled by the Regulator in the flex tube diaphragm Kit. Regulators are identified by color.

Note: Never use more water than needed. Low Consumption water closets and urinals will not function properly on excess water.

O-RING

REGULATOR

(MUST BE INSTALLED

PAST O-RING)

H-533

Page 5

8 - ASSEMBLE FLEX TUBE DIAPHRAGM TO SOLIS ASSEMBLY

Push diaphragm securely

SLOAN SOLIS®

ASSEMBLY

against underside of Sloan SOLIS

Assembly. Place entire Assembly onto the Valve Body.

Insert metal end

O-RING

FLEX TUBE DIAPHRAGM

into hole in base of Sloan SOLIS Assembly. O-ring must be fully inserted into the hole.

Make sure Flush

Volume Regulator is Installed Past O-ring.

To facilitate installation, wet the diaphragm assembly (on top or completely).

VALVE BODY

Note: Sensor Lens must face directly forward. Rotating the Sensor to either side will decrease the Sensor’s ability to detect a target.

9 - TIGHTEN LOCKING RING

Thread Locking Ring

onto Valve Body.

Use Strap Wrench

provided to tightly secure Locking Ring. Both wrench and coupling ring must be dry.

THE LOCKING RING MUST BE INSTALLED DOWN PAST

THE VALVE BODY THREADS BY AT LEAST ONE THREAD.

IF DIFFICULTY IS EXPERIENCED INSTALLING THE

LOCKING RING, TURN THE LOCKING RING BACK AND

FORTH, EACH TIME WORKING IT FURTHER DOWN THE

THREADS. THE LOCKING RING WILL ACT AS A THREAD

CHASER IN THE EVENT THERE HAS BEEN A BUILD-UP OF

MATTER ON THE THREADS OF THE OLD VALVE BODY.

If retrotting the Sloan SOLIS Ring must be used (identied by a machined groove around the ring). Order the Sloan SOLIS with this Ring.

!!! IMPORTANT !!!

onto a Zurn valve body, a special Locking

with the “Z” variation to receive theunitsupplied

10 - REMOVE TAPE FROM SOLAR PANEL AND SENSOR WINDOW TO ACTIVATE

Remove the tape located over solar panel.

Remove the tape located over sensor window.

For the first ten (10) minutes of operation, a visible light flashes in the sensing window of the SOLIS

flushometer when a user is

detected.

Page 6

11 - TEST SENSOR OPERATION

The Sloan SOLIS

has a factory set sensing range:

WaterClosetModels-22”to42”(559mmto1067mm) UrinalModels-15”to30”(381mmto762mm)

THE FACTORY SETTING SHOULD BE SATISFACTORY FOR MOST INSTALLATIONS. IF A RANGE ADJUSTMENT IS REQUIRED, REFER TO THE RANGE ADJUSTMENT INSTRUCTIONS ON NEXT PAGE.

Test Sensor with Cover in Place.

Stand in front of Sensor

for ten (10) seconds

12 - ADJUST CONTROL STOP AND INSTALL VANDAL RESISTANT STOP CAP

Open control Stop COUNTERCLOCKWISE ½ turn from closed

position.

Activate flushometer

by placing hand in front of Sloan SOLIS

Sensor Lens for ten (10) seconds (or press override button) and then moving it away.

Adjustcontrolstopaftereachflushuntiltherateofflowdelivered

properly cleanses the fixture.

SLOAN FLUSHOMETERS ARE ENGINEERED FOR QUIET

OPERATION. EXCESSIVE WATER FLOW CREATES NOISE,

WHILE TOO LITTLE WATER FLOW MAY NOT SATISFY THE

NEEDS OF THE FIXTURE. PROPER ADJUSTMENT IS MADE

WHEN PLUMBING FIXTURE IS CLEANSED AFTER EACH

FLUSH WITHOUT SPLASHING WATER OUT FROM THE LIP

AND A QUIET FLUSHING CYCLE IS ACHIEVED.

THE CONTROL STOP SHOULD NEVER BE OPENED TO THE

POINT WHERE THE FLOW FROM THE VALVE EXCEEDS

THE FLOW CAPABILITY OF THE FIXTURE. IN THE EVENT

OF A VALVE FAILURE, THE FIXTURE MUST BE ABLE TO

ACCOMMODATE A CONTINUOUS FLOW FROM THE VALVE.

!!! IMPORTANT !!!

Step away from Sensor

andlistenfor“CLICK.”

Install control stop cap onto control stop. For RESS retrofit applications, reuse stop cap from existing valve. In complete valve installations, a new stop

cap is provided. Follow the instructions packaged with the free spinning vanda resistant stop cap.

OPERATION

1. A continuous, INVISIBLE light beam is emitted from the Sloan SOLIS sensor.

2. As the user enters the beam’s effective range, 22 to 42 inches (559 mm to 1067 mm) for closet installations and 15 to 30 inches (381 mm to 762 mm) for urinal installations, the beam is reflected into the Scanner Window to activate the Output Circuit. Once activated, the Output Circuit continues

ina“hold”modeforaslongastheuserremainswithintheeffectiverange

of the sensor. Once the user steps away, a full flush will automatically initiate.

3. When the user steps away, this initiates a full flush. The circuit automatically resets and is ready for the next user.

4. In addition to the above the Sloan SOLIS

urinal incorporates a standard deferred flushing mode feature that accommodates the high volume usage seen in stadiums or similar high attendance facilities.

CLOSET

URINAL

BATTERY REPLACEMENT

When required, replace batteries with four (4) Alkaline AA-Size batteries.

Note: Water does not have to be turned off to replace batteries.

Loosen the two (2) Screws on top of unit. Remove the complete cover assembly. Lift the sensor module from its plate. Unplug the electrical connector from battery compartment cover. Loosen the retaining screw on battery compartment cover. Remove battery compartment cover and old batteries. Install four (4) fresh Alkaline AA-Size batteries exactly as illustrated.

COVER

ASSEMBLY

SENSOR MODULE

PLATE

RETAINING

SCREW

SENSOR MODULE

ELECTRICAL CONNECTOR RECEPTACLE

Install battery compartment cover and secure with retaining screw. Make certain that battery compartment cover is fully compressed against gasket to provide a seal; DO NOT overtighten. Plug the electrical connector into the battery compartment cover. Reinstall the sensor module onto the Plate. Reinstall the complete cover assembly onto the plate. Tighten the two (2) screws on top of the unit.

BATTERY

COMPARTMENT

COVER

Page 7

RANGE ADJUSTMENT (ADJUST ONLY IF NECESSARY)

The Sloan SOLIS® has a factory set sensing range:

WaterClosetModels-22”to42”(559mmto1067mm) UrinalModels-15”to30”(381mmto762mm)

CLOCKWISE

COUNTER-

CLOCKWISE

The Factory setting should be satisfactory for most installations.

If the range is too short (i.e., not picking up users) or too long (i.e., picking up

oppositewallorstalldoor)therangecanbeadjusted.

Decreases

Range

Note:Waterdoesnothavetobeturnedofftoadjustrange.

Loosen the two Screws on top of the unit and remove cover. Remove the Rubber Plug from top of Electronic Sensor Module to uncover the Potentiometer.

RANGE ADJUSTMENT PROCEDURE

For the first ten (10) minutes of operation, a Visible Light flashes in the sensing window of the SOLIS

flushometer when a user is detected. This visible light feature can be reactivated after ten (10) minutes by opening and closing the battery compartment door. Check the range by stepping toward the unit until

thelightflashes,indicatingthesensor’smaximumdetectionlimit.Adjustthe

range potentiometer screw located on top of the sensor module a few degrees CLOCKWISE to increase the range or a few degrees COUNTER-CLOCKWISE to

decreasetherange.Repeatthisadjustmentuntilthedesiredrangeisachieved.

Always determine the sensing range with metal cover and lens window on top of the unit.

IMPORTANT: Adjust in small increments only! Range Potentiometer Adjustment Screw rotates only ¾ of a turn; DO NOT over-rotate.

Whenrangeadjustmentissatisfactory,replacetheRubberPlug.Reinstall Cover and tighten the two Screws on top of the unit.

CARE AND CLEANING

DO NOT use abrasive or chemical cleaners to clean flushometers as they may dull the luster and attack the chrome or special decorative finishes. Use ONLY soap and water, then wipe dry with clean cloth or towel.

While cleaning the bathroom tile, the flushometer should be protected from any splattering of cleaner. Acids and cleaning fluids can discolor or remove chrome plating.

Increases

Range

TROUBLESHOOTING GUIDE

1. Sensor flashes continuously only when user steps within range.

A. Unit in start-up mode; no problem. This feature is active for the first ten

(10) minutes of operation.

2. Valve does not flush; densor not picking up user.

A. Range too short; increase the range.

3. Valve does not flush; densor picking up opposite wall or

surface, or only flushes when someone walks by. Light flashes continuously for first 10 minutes even with no one in front of the sensor.

A. Range too long; shorten range.

4. Valve Does not flush Even After Adjustment.

A.Rangeadjustmentpotentiometersetatfull“max”orfull“min”setting.

Readjustpotentiometerawayfromfull“max”or“min”setting.

B. Batteries completely used up; replace batteries. C. Problem with electronic sensor module; replace electronic sensor module.

5. Unit flashes 4 quick times when user steps within range.

A. Batteries low; replace batteries.

6. Valve does not shut off.

A. Bypass orifice in diaphragm is clogged with dirt or debris, or bypass

iscloggedbyaninvisiblegelatinousfilmdueto“over-treated”water.

Remove flex tube diaphragm and wash under running water.

Note: Size of Orifice in the bypass is of utmost importance for the proper metering of water by the valve. DO NOT ENLARGE OR DAMAGE THIS ORIFICE. Replace flex tube diaphragm if cleaning

does not correct the problem.

B. Dirt or debris fouling stem or flex tube diaphragm. Remove flex tube

diaphragm and wash under running water.

C. O-ring on stem of flex tube diaphragm is damaged or worn. Replace

o-ring if necessary.

D. Problem with electronic sensor module; replace sensor module.

7. Not Enough Water to Fixture.

A. Wrong flush volume regulator installed in flex tube diaphragm kit. Install

the correct regulator.

B. Wrong Sloan SOLIS model installed; i.e., 1.0 gpf Urinal installed on 3.5

gallon closet fixture. Replace with proper SOLIS model.

C. Enlarged bypass in diaphragm. Replace flex tube diaphragm.

D.Controlstopnotadjustedproperly.Readjustcontrolstop.

E. Inadequate volume or pressure at supply. Increase water pressure or

supply (flow) to valve. Consult factory for assistance.

8. Too Much Water to Fixture.

A. Wrong flush volume regulator installed in flex tube diaphragm kit. Install

the correct regulator.

B.ControlStopnotadjustedproperly.Readjustcontrolstop.

C. Wrong SOLIS

model installed; i.e., 3 gpf model installed on 1.0 or 1.5

gallon urinal fixture. Replace with proper SOLIS model.

D. Dirt in diaphragm bypass. Clean under running water or replace flex tube

diaphragm.

Note: The EBV-46-A beam deflector is not required or available for the SOLIS

Note: Troubleshooting also applies to the SOLIS urinals.

If further assistance is required, please contact the

Sloan Technical Support at:

1-888-SLOAN-14 (1-888-756-2614)

!!! IMPORTANT !!!

LAWS AND REGULATIONS PROHIBIT THE

USE OF HIGHER FLUSHING VOLUMES THAN

LISTED ON FIXTURE OR FLUSHOMETER.

Page 8

PARTS LIST

18A

18B 18D

20A

18C

20B

20C

FLEX TUBE DIAPHRAGM ASSEMBLY

Sloan SOLIS® valve models feature Sloan’s exclusive flex tube diaphragm for the ultimate in valve performance, reliability and chloramines resistance.

Item # Part # Description

Items Included with RESS Retrofit and Complete Sloan SOLIS Valves

1 EBV-304-A Cover/Sensor/Assembly - Closet Solis Electronic Single

Button Flush

EBV-320-A Cover/Sensor/Assembly (Zurn) - Closet Solis Electronic

Single Button Flush

EBV-306-A Cover/Sensor/Assembly - Urinal Solis Electronic

Single Button

EBV-321-A Cover/Sensor/Assembly (Zurn) - Urinal Solis Electronic

Single Button 2 EBV-309-A Cover Assembly - Solis Electronic Single Button Flush 3 EBV-14 Locking Ring EBV-30 Locking Ring - for Zurn valves 4 EBV-312-A-C Sensor Assembly Solis - Water Closet EBV-312-A-U Sensor Assembly Solis - Urinal 5 EBV-134 Cover Rest Plate 6 EBV-145-A Inside Cover Assembly (includes solenoid) 7 EBV-136-A Solenoid 8 † Flex Tube Diaphragm Assembly 9 † Flush Volume Regulator 10 EBV-1017-A Handle Cap

 11 EBV-91 RangeAdjustmentTool

12 EBV-22 Strap Wrench

 13 EBV-137 7/64”HexWrench

Item # Part # Description

Items Included with Complete Sloan SOLIS

Valves Only

 14 H-633-AA 1”(25mm)SweatSolderKit   H-636-AA ¾”(19mm)SweatSolderKit  15 H-700-A 1”(25mm)Bak-Chek   H-700-A ¾”(19mm)Bak-Chek

Control Stop

Control Stop 16 H-1010-A Vandal Resistant Stop Cap 17 EBV-36-A Valve Body  18A V-600-AA 1½”(38mm)x10½”(229mm)VacuumBreaker

(Model 8110/8111)

  V-600-AA 1½”(38mm)x15”(584mm)VacuumBreaker

(Model 8113)

  V-600-AA 1½”(38mm)x23”(584mm)VacuumBreaker

(Model 8115)

  V-600-AA 1½”(38mm)x26”(660mm)VacuumBreaker

(Model 8116)

 18B V-600-A 3”(76mm)VacuumBreakerAssembly  18C V-600-AA 1¼”(32mm)x10½”(229mm)VacuumBreaker

(Model 8180)

 18D V-600-AA ¾”(19mm)x10½”(229mm)VacuumBreaker

(Model 8186)

 19 F-109 1½”(38mm)ElbowFlushConnection  20A F-5-AT 1½”SpudCouplingAssembly(WaterClosetModels)  20B F-5-AU 1¼”SpudCouplingAssembly(Model8180)  20C F-5-AW ¾”SpudCouplingAssembly(Model8186)

† Flow volume varies with valve model and desired flush volume.

Manufactured in the U.S.A. by Sloan Valve Company under one or more of the following patents: U.S. Patents: D598,975; D599,436; 7,124,997. Other Patents Pending. BAK-CHEK

Theinformationcontainedinthisdocumentissubjecttochangewithoutnotice.

, PARA-FLO®, PERMEX®, TURBO-FLO®.

SLOANHEADQUARTERS•10500SEYMOURAVENUE•FRANKLINPARK,IL60131

Phone:1-800-982-5839or1-847-671-4300•Fax:1-800-447-8329or1-847-671-4380•www.sloanvalve.com