SlimLine CLIM9000CE User Manual

CLIM9000CE

PORTABLE AIR CONDITIONER

USER MANUAL

Please read this user manual before using this innovative Air Conditioner and keep it

safe for future reference.

2

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit

• This appliance is for indoor use only.

• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.

• Installation must be in accordance with regulations of the country where the unit is used.

• If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary,

modified by a qualified electrician.

• This air conditioner has been tested and is safe to use. However, as with any electrical appliances - use it with
care.

• Disconnect the power plug from socket before dismantling, assembling or cleaning.

• Avoid touching any moving parts of the appliance.

• Never insert fingers, pencils or any other objects though the guard

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance by a person responsible for
their safety.
Do not leave children unsupervised with this appliance.

• Do not clean the unit by spraying it or immersing it in water.

• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should

be installed by a qualified electrician.

• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or
exposed to sharp object/edges.

• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a
hazard.

• Any service other than regular cleaning or filter replacement should be performed by an authorised service
representative. Failure to comply could result in a voided warranty.

• Do not use the appliance for any other purposes than its intended use.

• The air conditioner unit must always be stored and transported upright, otherwise irreparable damage may
be caused to the compressor; if in doubt we suggest waiting at least 24 hours before starting the unit.

• Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off.
This prevents damage to the compressor.

• Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the provided ON/OFF
switch located on the control panel.

• Always place the unit on a dry and stable surface.

• The appliance should not be installed in laundry or wet rooms

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow from the outlet or inlet grills.

• For maximum performance the minimum distance from a wall or objects should be 50cm.

• Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks

(approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary,
depending on the air quality.

• For the initial start up set the fan speed to maximum and the thermostat to 4-5 degrees lower than the
current temperature. After, set the fan switch to low and set the thermostat to your desired setting.

• To protect the unit we recommend not using the cooling function when the ambient temperature is higher
than 35oC.

3

PARTS

1. Handle

2. Control Panel

3. Air-outlet

4. Fan blade

5. Castor

Back Side

6. Filter frame upper

7. Exhaust connector

8. Power Cord Location

9. Filter Frame Lower

10. Rubber plug

11. Plug Cap

12. Power supply cord

Installation

Warning: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed on an even
surface.

1. Assemble the fishtail connector on to the hose.

2. Assemble the exhaust hose to the air conditioner body.

4

Extend one head of the hose and screw it into the unit anti-clockwise. The hose can be removed by screwing the
hose clockwise.

3. In the same way connect the hose to the assembled adaptor (at least three rotations).

4. Installation of window kits.

Partially open the window and then fix the window kit to the window.

5. Make sure the unit is upright and there are no obstructions to the air inlets and outlet grills.

6. Fix the other end of the hose to the air-outlet window kit.

Note: The window kit is only designed to be installed with sliding or sash windows or doors. The window kit is

not designed or to be used with any other style of windows. However, the fish tail adaptor can be used with
most windows / doors. When using in cooling mode ensure that the opening left around the fishtail is as small
as possible as the cooling will be less efficient. The best form of installation is through a wall duct. By properly
venting you expel hot air from your room while efficiently cooling it.