Page 1
www.SleepPhones.com
WIRELESS CHARGING INSTRUCTIONS
Open the Velcro® in the back of the headband. Remove the Bluetooth®
module by unplugging it from the speakers. Plug the micro-USB cable into
the micro-USB port on the Bluetooth® module. Plug the standard USB end
of the cable into the USB port on your computer or any USB wall adaptor.
The Bluetooth® module comes with a partial charge. When you plug the
module in to charge, you will notice a blinking red light. The red light will
turn off when the Bluetooth® module is fully charged. A fully charged
module will play for up to 13 hours.
Quick Start Guide
Before pairing, fully charge your SleepPhones® Wireless headphones.
Place your Bluetooth® device within 3 feet (1 meter) of your SleepPhones®.
Find the middle square button on the wireless Bluetooth® module located
inside the headband.
Press and hold the square button for 5 full seconds until you hear an
ascending 3 ring tone followed by a series of beeps. The series of beeps
indicate that the module is in pairing mode.
Next, go into the Bluetooth® settings on your device and turn on Bluetooth®.
After a few seconds, “AcousticSheep” will appear in the list of devices. Click on
“AcousticSheep” to pair your device to the Bluetooth® module. You will hear a
long beep to indicate that it is paired with your device.
-OR-
Navigate to the Bluetooth® connections menu on your Bluetooth® enabled device.
When “AcousticSheep” appears, click to pair your device to the Bluetooth® module.
You will hear a long beep to indicate that it is paired with your device.
PAIRING INSTRUCTIONS
To watch our video on how to use SleepPhones® Wireless
visit: www.SleepPhones.com/our-story/sleep-better-videos
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth® SIG, Inc., and any use
of such marks by AcousticSheep LLC are under license.
Other trademarks and trade names are those of their
respective owners.
AS-SB-US-QUICK-03
Page 2
www.SleepPhones.com
OPERATING INSTRUCTIONS
VOLUME: Click the “up” arrow button to increase the volume. Holding the
“up” arrow button will also increase the volume at a faster pace. Click the
“down” arrow button to decrease the volume. Holding the “down” arrow
button will also decrease the volume at a faster pace.
SKIP TRACK(S): Double click the “up” arrow button to advance to the next
track. Double click the “down” arrow button to go to the previous track.
PAUSE: Click the middle square button once to pause the music. Click once
again to resume playing music.
POWER OFF: To turn the device off, press and hold the middle square button
for 3 seconds. You will hear a descending 3 ring tone.
While charging, if the red light is on, the module is not fully charged.
If there is NO light on at all while charging, the Bluetooth® module is
fully charged.
NOT SURE IF FULLY
CHARGED
UNABLE TO PAIR
FOR THE FIRST TIME
When you turn on the device, make sure to continue holding down the
button for a full 5 seconds until you hear an ascending 3 ring tone followed
by a series of beeps. The beeps indicate that the module is in pairing mode.
UNABLE TO PAIR
If your Bluetooth® enabled device is unable to pair with the AcousticSheep®
module, you may need to reset the Bluetooth® module. To reset the
Bluetooth® module, turn it on. Hold both the “up” and “down” arrow
buttons down for 7 seconds. Once the reset function is complete there
will be two long tones. The Bluetooth® module must be turned off and
then turned back on for it to enter into pairing mode.
UNABLE TO FIND
THE DEVICE
If your AcousticSheep® module was previously paired with another device,
it will automatically pair with that device if the device is within range.
Make sure that the Bluetooth® on all other previously paired devices is
turned off or out of range when you are pairing with a new device.
Slide the speakers inside the headband to position them over your ears.
Check the volume on your Bluetooth® audio player.
Check the volume on the wireless Bluetooth® module located inside
the headband.
Make sure that the wireless Bluetooth® module is charged.
If your Bluetooth® device is separated from your SleepPhones® Wireless
headphones for more than 5 minutes, the headphones will automatically
power off. Not all applications or software support Bluetooth®.
1
2
3
4
THERE IS NO SOUND
WHEN PAIRED
TROUBLESHOOTING
Quick Start Guide
5
Loading...