Skyworth LCD-32L29 User Manual
Introduction
Safety Precaution
To ensure safety and best performance of your product, this manual introduces of using,
setting and other important information. Please read the manual carefully before using
this product.
Cleaning Unplug the AC cord form the wall outlet before
cleaning.Do not use liquid cleaners or aerosol cleaners.
Use a dry cloth for cleaning. Do not use corrosive cloth.
Do not use sharp object scratch this LCD board and shell.
Heat sources - Do not install the product near any heat
sources such as radiators; heaters, stoves and other heat generating products (including amplifiers).
Do not insert foreign objects. Placing objects into the vent holes (rear cabinet) may
cause an electric shock and electric short circuit.
Wall mount installation - Please comply with manufacturer's instructions to install the
product on the wall and ceiling installation. Use only the mounting hardware
recommended by the manufacturer.
Water and moisture - Do not use the product near water, such as bathtub, washbasin,
laundry tub, in a wet basement and swimming pool, etc.
Electrical source - Do not connect too many electrical items to the same socket
outlet, it may cause in fire or electric shock.
Servicing - Do not attempt to repair the product yourself. Removing covers can
expose you to high voltage and other dangerous conditions. Request our qualified
repairer to perform servicing
Product protection - To prevent damage due to lightning storm, please unplug
it from the wall outlet and disconnect the antenna or cable system.
Wire protection - Please protect the electrical wire and do not stomp, twist and
squeeze it. Careful to inspect the plug and electrical wire.
Earthing device - Make sure connect the earth wire to prevent possible electric shock.
If grounding methods are not possible, have a qualified electrician install a separate
circuit breaker.
To avoid still picture for a long time
Do not display a still picture for a long time; this may cause an afterimage to remain.
Suggestion:
Do not still picture exceeding half hour, this may cause an
afterimage.
Do not still picture for a long time when play the TV game or
see a movies.
Please reduce the brightness and contrast ratio before still picture.
The warranty service doses not contain the problem of afterimage.
Connection and Basic Operations
Standard Accessories
Host Panel
Rear Connection Diagram
Installation and Connection
Remote Controller
Batteries Installation
Power ON/OFF
Standby Mode
Picture Setting
Sound Setting
Channel Setting
Time Setting
Option Setting
PC Setting
Install PC Software
Display Mode
Troubleshooting
Technical Specifications
32” Wide Screen LCD TV
Contents
Ｐ．Ｍ Ｓ．Ｍ ＭＵＴＥ
ＳＬＥＥＰ ＡＳＰＥＣＴＦＲＥＥＺＥ ＥＰＧ
ＦＡＶ ＴＶ／ＲＡＤＩＯ ＳＵＢＴＩＴＬＥ
ＬＩＳＴ
ＰＲＯＧ
ＶＯＬ
ＩＮＦＯ
ＳＯＵＲＣＥ
ＭＥＮＵ
ＴＶ／ＡＶ ＯＮ／ＯＦＦ
ＭＥＮＵ
ＴＶ／ＡＶ ＯＮ／ＯＦＦ
－
＋ ＶＯＬ
－
＋ ＶＯＬ ＋ ＰＲＯＧ
5
2
4
3
2
1
6
7
8
+
-
+
-
Basic Operations
Standard Accessories
Remote Controller
Batteries
User Manual
AV Cable
Host Panel
1. Press this key to power on TV or enter standby state.
2. Video Signal
Video input mode. DTV, TV, Component, PC, HDMI1,
HDMI2, HDMI3, Video1, Video2, S-Video.
3. Menu
Display the main menu on the screen.
4. Volume＋/－
Adjust the volume.
5. Channel＋/－
Select TV channels.
6. Power Indicator
The indicator turns red when the TV is in standby mode.
7. Remote Control Sensor
Receive signal from the remote controller.
8. Sound Speaker
1 2 3 4 5 6 7 8 9 10
11
12
13
14
S/PDIF
EARPHONE
VGA
HDMI1
VGA AUDIO
Pb
PrY
L - AUDIO - RVIDEO
S-VID EO
HDMI2
AV2
L - AUDIO - RVIDEO
L - AUDIO - RVIDEO
AV1
AV OUT
HDMI3
USB
Rear Connection Diagram
Head Phone Output Interface
Coaxial Output Interface (S/PDIF)
USB Interface for software update
HDMI 1/HDMI 2/HDMI3
-Support to connect HDMI output devices .(STB, DVD Player, AV device and Digital TV)
-HDMI connects with HDMI, video and audio signal are transmitted by one cable.
PC Audio Input Interface (VGA AUDIO)
-Connect one end of the stereo audio cable into the plug of “personal computer
audio output (VGA AUDIO)” at the back of TV.
Connect to PC
-Connect this VGA interface to the VGA interface of personal computer.
Video Output Interface
S-Video Output Interface
- S-Video, Video1 and YPBPR use the same group audio interface.
Connect with Antenna and Cable TV Network
- To correct watch TV channels, it must receive signals with one of the bellow signal
source: outdoor antenna/cable TV broadcast/satellite broadcast.
YPBPR--Make up Equipment Connection
- Connect an end of component to an interface of the back of TV. (Y, Pb, Pr), and
another end to the corresponded output interface of component video of DVD
- Combine YPBPR of the equipment (DTV or DVD) AV connector, or marked as Y, BY, R-Y, or Y, Cb, Cr.
- Connect RCA audio to left audio “AUDIO (L)” and right audio “AUDIO (R)”
interfaces in the back of TV, and another end to the corresponded audio output
interface “AUDIO OUT” of DTV or DVD.
Video Output Interface
Installation and Connection
Connect VHF/UHF Antenna
UHF/VHF
antenna
300/75-ohm adapter (except)
300-ohm power cable
Power Connection
Press ON/OFF key on the remote controller to power on TV or enter Standby state.
Please disconnect the power when the TV is going not to use for a long time.
Pressing ON/OFF key to power on TV or enter Standby state can not cut
off the power supply.
Please pull out the power plug if need to cut of the power.
Use Video Cable to Connect AV Device
AV cable
Game machine
Camera
DVD player
Satellite signal receiver
TV box
Use the video cable to connect AV device to this machine
Please check the connection of all signal cables before pressing ON/OFF key
Press ON/OFF key on the remote controller to power on TV
Press Video Signal key on the remote controller to enter the function list
and then press key to select AV option, press OK key to confirm
S/PDIF
EARPHONE
VGA
HDMI1
VGA AUDIO
Pb
PrY
L - AUDIO - RVIDEO
S-VID EO
HDMI2
AV2
L - AUDIO - RVIDEO
L - AUDIO - RVIDEO
AV1
AV OUT
HDMI3
USB
Loading...