Skyworth LCD-32L16H User Manual

Instruction Manual

LCD-32L16HLCD-32L16H

32" LCD TV/MONITOR

WARNING AND PRECAUTION

Read all of the instructions before operating the set. Keep these instructions well for later use.

PRODUCT

The ventilation should not be impede by covering the ventilation openings with items, such as newspaper, table-cloths, curtains, etc.

Do not push any objects of any kind into this unit through the cabinet slots as they could touch the current carrying parts or short-circuit parts, resulting in fire, electric shock, or damage to the unit.

Unplug the set when it is not used for a long period of time. Do not dismantle this product by yourself as this may cause damage. Do not touch the screen surface with fingers as this may scratch or mar the

LCD screen. Do not impact the LCD screen with hard pressure as this may damage the

LCD screen severely. The battery (battery or batteries or battery pack) shall not be exposed

to excessive heat such as sunshine, fire or the like.

POWER

Please use the core plug as required.

PLUG

Unplug the set under the following conditions:

If the set will not be used for a long period of time. If the power cord or the power outlet/plug is damaged. Follow the instructions to install and adjust the product. Adjust those

controls that are covered in this operating instructions as improper adjustment of other controls may result in damage. If this happens, unplug the set and refer to the service personnel.

If the set is subject to impact or has been dropped to have the cabinet damaged.

The mains plug is used as the disconnect device and shall remain readily operable.

POWER CORD & SIGNAL CABLE

Do not allow anything to rest on or roll over the power cord & signal cable. Protect the power cord & signal cable from being trampled. Do not overload the power cord or power outlet. Do not expose the power cord & signal cable to moisture.

WARNING AND PRECAUTION

USE ENVIRONMENT

Do not install this equipment in a confined space such as a book case or similar unit. To prevent injury, this apparatus must be securely

attached to the wall mount fastened on the wall.

Place the set on a place that allows good ventilation. Do not use the set near damp, and cold areas, protect the set from

overheating.

Keep away from direct sunlight.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not use the set near dust place.

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

CLEANING

Dust the set by wiping the screen and cabinet with a soft, clean cloth or some special liquid cleaner.

Do not apply excessive force to the screen when cleaning. Do not use water or other chemical cleaner to clean the screen as this

may damage the surface of the LCD screen.

SETUPSETUP

Insert The Batteries

Remove the battery cover by pressing it and sliding it down.

Insert the two 1.5V (AAA size) batteries making sure the polarity (+ or -)of the batteries matches the polarity marks Inside the unit.

Replace the battery cover by sliding it in until you hear a click sound.

Precautions when using batteries Do not use old and new batteries together. Do not use different types of batteries (for example, Manganese and Alkaline batteries) together. Note that there are chargeable and non-chargeable batteries. Do not attempt to charge non-chargeable batteries. Remove the batteries from the remote control unit if you do not intend to use the unit for a long time. Precautions when using the remote control unit Do not drop the remote control unit. Do not subject the remote control unit to physical shocks. Keep the remote control unit dry. May cause the unit to malfunction. Replace the batteries with new ones when operation of the unit deteriorates.

TV Installation

-1-

SETUPSETUP

Locate the receiver in the room where direct light does not strike the screen. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect

lighting is recommended for comfortable viewing. Allow enough space between the receiver and the wall to permit ventilation. Avoid excessively warm locations to prevent possible damage to the cabinet or premature

component failure. This TV operates on AC supply directly, connect the AC plug to the socket at the back of the TV.

Insert the mains plug in the socket having a mains voltage of 100-240V AC. Do not install the receiver in a location near heat sources such as radiator, air ducts, direct

sunlight, or in a place somewhere like close compartment and close area. Do not cover the ventilation openings when using the set.

Features

Up to 200 programme memory. Program Organiser . Sleep timer. 4:3 format , 16:9 format ,14:9 zoom , 16:9 ZOOM1,16:9 ZOOM2

picture modes. When no TV signal is dectected, after 15 minutes the TV switches itself a utomatically to stand-bymode. CYS: PAL / SECAM / NTSC SYS: BG/DK / I / M HDMI Input (support up to 1 080P) PC Input (support up to 1 080i) NICAM Stereo / AV Stereo

Panel Features

High resolution (1366x768), 32" TFT LCD display. Brightness: 500cd/m

High-speed response time <8msec. 8-bit color depth, display 16.2M colors. High contrast ratio (1200:1 Typital) Viewing angle:178 (H)/178 (V)(CR>10).

In The Box

You should have:

Tele vision

Remote control User Guide Warranty Card

2 x AAA battery Stand

Wall mount

-2-

FUNCTIONAL PARTS

FRONT PANEL

Note: The graphics are for representation only.

PROG.+

PROG.-

VOL.+

VOL.-

1.Power button

5. Menu button

TV/AV

2. Power Indicator/Remote Sensor

4.Volume Up/Down button3.Program Up/Down button

6. TV/AV button

7. Speakers

-3-

FUNCTIONAL PARTS

BACK PANEL

AV1

AV OUT

75 ANT

HDMI2

HDMI1

1 2

L - AUDIO - R VIDEO

VGA

VGA AUDIO IN

AV2

S/PDIF

PrY

R - AUDIO - L VIDEO

6 7 8 9

1. HDMI1\HDMI2: Connect HDMI input signal from signal source such as DVD.

2. VGA: Connect a PC via a VGA cable.

3. VGA AUDIO IN: Connect audio signal from PC.

4. Y Pb Pr(HDTV): Connect

RCA cable to connect DVD player or other video device's YPbPr output.

5. AV2: Connect AUDIO and VIDEO input signal from signal source such as DVD.

6. S/PDIF : Connect digital AUDIO output signal.

7. AV OUT : Connect AUDIO and VIDEO output signal.

8. AV1 : Connect AUDIO and VIDEO input signal .

9. ANTENNA IN: Connect a coaxial cable to receive signal from the antenna or cable.

-4-

+ 14 hidden pages