Skyworth LCD-26L16H User Manual

Download

Page 1

Instruction Manual

LCD-26L16HLCD-26L16H

26" LCD TV/MONITOR

Page 2

Thank you very much for your purchase of this product-the most natural Colour Television Receiver. To enjoy your set to the full from the very beginning, read this manual carefully and keep it handy for ready reference.

Page 3

Page 4

SETUPSETUP

Insert The Batteries

Remove the battery cover by pressing it and sliding it down.

Insert the two 1.5V (AAA size) batteries making sure the polarity (+ or -)of the batteries matches the polarity marks Inside the unit.

Replace the battery cover by sliding it in until you hear a click sound.

Precautions when using batteries Do not use old and new batteries together. Do not use different types of batteries (for example, Manganese and Alkaline batteries) together. Note that there are chargeable and non-chargeable batteries. Do not attempt to charge non-chargeable batteries. Remove the batteries from the remote control unit if you do not intend to use the unit for a long time. Precautions when using the remote control unit Do not drop the remote control unit. Do not subject the remote control unit to physical shocks. Keep the remote control unit dry. May cause the unit to malfunction. Replace the batteries with new ones when operation of the unit deteriorates.

TV Installation

-1-

Page 5

SETUPSETUP

Locate the receiver in the room where direct light does not strike the screen.

Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect

lighting is recommended for comfortable viewing.

Allow enough space between the receiver and the wall to permit ventilation.

Avoid excessively warm locations to prevent possible damage to the cabinet or premature

component failure.

This TV operates on AC supply directly, connect the AC plug to the socket at the back of the TV.

Insert the mains plug in the socket having a mains voltage of 100-240V AC.

Do not install the receiver in a location near heat sources such as radiator, air ducts, direct

sunlight, or in a place somewhere like close compartment and close area. Do not cover the

ventilation openings when using the set.

Features

Up to 200 programme memory.

Program organiser

. Sleep timer.

4:3 format , 16:9 format ,14:9 zoom , 16:9 ZOOM1,16:9 ZOOM2

picture modes. When no TV signal is dectected, after 15 minutes the TV switches itself automatically to stand-bymode. CYS: PAL / SECAM / NTSC SYS: BG/DK / I / M HDMI Input (support up to 1080P) PC Input (support up to 1080i) NICAM Stereo / AV Stereo

Panel Features

High resolution (1366x768), 26" TFT LCD

display.

Brightness: 400cd/m High-speed response time <8msec.

8-bit color depth, display 16.2M colors.

High contrast ratio (800:1 Typital)

Viewing angle:160 (H)/150 (V)(CR>10).

In The Box

You should have:

Television

Remote control

User Guide

Warranty Card

2 x AAA battery

Stand

Wall mount

-2-

Page 6

FUNCTIONAL PARTS

1. ON/OFF Switch

2. Power Indicator

3. Remote Sensor

4. TV / AV

5. MENU

6. VOL.- Button

7. V0L. + Button

8. PROG.- Button

9. PROG.+ Button

10. Speakers

11. Aerial input socket

12. AV Input

13. AV Output

14. YPbPr Input

15. VGA Audio Input

16. VGA Input

17. HDMI1 Input

18. HDMI2 Input

1 2

TV/AV

VOL.-

VOL.+

PROG.-

PROG.+

HDMI1HDMI2

1818

VGA

LEFT -AUDIO- RIGHT

VGA AUDIO IN

PrY

1616

1515

14141717

RIGHT -AUDIO- LEFT

AV IN

VIDEO

AV OUT

VIDEORIGHT -AUDIO- LEFT

1313

75 ANT

1212

1111

-3-

Page 7

FUNCTIONAL PARTS

HDMI CABLE CONNECTIONS

Important information s both HD player and display before making any connections. Connect the HDMI cable to the HDMI socket of the TV, connect the other end to the HDMI output socket of the HD player source.

witch off

HDMI1HDMI2

HDMI

HDMI CABLE NOT SUPPLIED. Connect the HDMI cable to the HDMI input on the TV. Connect the other end of this cable to your HD device.

HDMI

Device HDMI

VGA

VGA AUDIO IN

LEFT -AUDIO- RIGHT

AV IN

RIGHT -AUDIO- LEFT

PrY

VIDEO

AV OUT

VIDEORIGHT -AUDIO- LEFT

75 ANT

-4-

Page 8

OPERATION INSTRUCTIONS

Remote Control Unit

POWER

AV/TV

SLEEP

VOL

PICTURE SOUND

PIP ON/OFF PIP S OURCE PIP SOUND PIP SIZE

MIXTEXT

Sub-page

INDEX

INFO

FAV.

REVEAL

MUTE

RECALL

PROG

EXIT

NICAM

SIZEHOLD

CANCEL

POWER (STAND BY) BUTTON (

Press this button to turn the TV on/off.

MUTE BUTTON ( )

)

Press once to mute the sound, press again to return to preset sound level.

PROGRAM SELECTION BUTTONS (0-9) You could select program you want with 0-9 button. For program up to 100-199, you need press three digit number quickly, then TV will go to the program directly. For program between 10-99, you need press two digit number according program quickly and wait, then TV will go to the program. For program between 0-9 , just press one digit and wait .

AV/TV BUTTON

Press this button to display external video signal Such as TV/AV IN/HDTV/ VGA/HDMI1/HDMI2. Press up/down arrow key to select item and press left/right arrow key to enter selected item.

QUICK VIEW BUTTON (RECALL) Press this button to return to the previously viewed program.

SLEEP BUTTON(SLEEP) Press this button to set the sleep timer. When the preset length of time has passed, the TV set Enters standby mode. The time change(minutes):10,20,30,40,50,60,90,120, off

---.

INFO BUTTON

Press this button to display the settings on the screen.(e.g. Channel number for TV input, channel name, colour system).

PROGRAM UP/DOWN BUTTONS (PROG.+/-)

Press the PROG.+ button to select the program Forwards. Press the PROG.- button to select the program backwards.

VOLUME UP/DOWN BUTTONS (VOL.+/-) Press VOL+/- buttons to adjust sound level. Or adjust the volume of each item in the menu status.

-5-

Page 9

OPERATION INSTRUCTIONS

Remote Control Unit

POWER

AV/TV

SLEEP

VOL

PICTURE SOUND

PIP ON/OFF PIP S OURCE PIP SOUND PIP SIZE

MIXTEXT

Sub-page

INDEX

INFO

FAV.

REVEAL

MUTE

RECALL

PROG

EXIT

NICAM

SIZEHOLD

CANCEL

Left Right arrow/Zoom-/+ (Z- / Z+) Press to change the screen format: 4:3 format, 16:9

format, 14:9 ZOOM, 16:9 ZOOM1, 16:9 ZOOM2.

OK BUTTON (OK) Press to enter selected item.

CURSOR button( / ) Left/Right/Up/Down direction keys for selecting menu itemsor signal sources.

MENU BUTTON (MENU) Press this button to enter the menu screens for various Optional adjustable settings.

EXIT BUTTON Press to exit MENU directly.

PICTURE Button Press to change the picture setting :Normal , soft ,

personal, bright .

SOUND Button

Press to change the sound setting :standard, Music, Film, Voice, Personal .

Fav. BUTTON

Press Fav. button to switch favourite channel which you had set in Favourite channel MENU. If there is no channel in Favourite channel list, there is no response for this Fav. Button.

SOUND MODE BUTTON(NICAM) Press this button, you can select different sound mode when the source is different.

The NICAM selection is common for all TV channels .

TV SOURCE

1. MONO: MONO

2. STEREO: MONO, STEREO

3. DUAL : MONO, DUAL1, DUAL2

PIP ON/OFF

Press this button to switch on or off PIP function . PIP function is available in HDTV, VGA, HDMI mode only.

PIP SOURCE Press this button to select PIP source from TV, AV when PIP is active.

-6-

Page 10

OPERATION INSTRUCTIONS

PIP SOUND

Press this button to select current sound output from main or PIP source when PIP is active .

POWER

AV/TV

SLEEP

VOL

PICTURE SOUND

PIP ON/OFF PIP S OURCE PIP SOUND PIP SIZE

MIXTEXT

Sub-page

INDEX

INFO

FAV.

REVEAL

RECALL

PROG

NICAM

SIZEHOLD

CANCEL

MUTE

EXIT

PIP SIZE Press this button to change PIP picture size , Normal or Zoom when PIP is active .

TEXT BUTTON

This button is used for entering the teletext MENU.

MIX BUTTON(OPTION)

the button is used as closing /opening the teletext Background.

HOLD BUTTON Press this button to hold the Teletext page without update to prevent the page from changing. Press again to release the hold state.

SIZE BUTTON Press this button you can select different image sizes: Normal, double high top, double high bottom.

INDEX BUTTON (OPTION) Press this button to enter the Teletext's index MENU.

SUB.PAGE BUTTON (OPTION) Subcode mode, gives, the possibility to select certain subcode pages of a teletext page.

REVEAL BUTTON (OPTION)

Press this button to reveal the hidden information for so me Teletext pages press again to hide the information.

CANCEL BUTTON (OPTION) Press this button to appear the TV signal on the background.

F1-F4 (OPTION) These four color key are for relative fast teletext function in the bottom of teletext page and organizer function relative operation.

-7-

Page 11

SIZE

REVEAL

Text

You could

stop it by press "HOLD" button .

Up arrow key

Down arrow key

MIX

SIZE

SUB.PAGE

INDEX

1000

So TV will display text page you required quickly .

-8-

Page 12

Up arrow key

Down arrow key

To Cancel TEXT

Press "CANCEL" button to clear the TEXT. But the page number is still displayed on the left top of the screen. NOTICE: However, Teletextis playing all the same on the background at the time. Press " CANCEL" button again to resume the TEXT.

To Freeze TEXT

Press "HOLD" button to hold a Text Page. This means the page will not change and refresh. Press the button again to release the hold state.

To exit Teletext

Press the " TEXT " or " EXIT" button. The screen will switch to TV mode.

Note : If there is no teletext signal in your region , when you press "TEXT" button , you could entry teletext mode also , but TV will show top and bottom line only as graphics below , all teletext function is not available .

100

P +

110 200

P -

-9-

Page 13

ANALOG MENU SCREENS

1. Plug in the power cord and switch on power switch . The power indicator will light up. If TV is in stand by mode. Then Press"¡¡ " Key. The picture will display in few minutes.

MENU BUTTON

1.Press menu button to display menu, and press left/right arrow key to select sub menu.

PICTURE

2.After entering an item, you can select the desired adjusting item by the up/down

arrow key and adjust It by the left/right arrow key buttons.

Picture menu

SOUND

INSTALLATION

TIMER

Enter picture menu, you can select Picture Preset, Contrast, Brightness, Colour, Sharpness, and Noise Reduction. items by pressing

up/down arrow key.

Picture Preset Press the left/right arrow key to change the Picture Preset. Such as SOFT, NORMAL, BRIGHT, Or Personal. Choose the setting that is best for your viewing environment.

Contrast Press the left/right arrow key to increase /Decrease the contrast of the picture.

Brightness Press the left/right arrow key to lighten/darken the picture.

PREFERENCE PARENTAL CONTROL

Colour (not available on PC) Press the left/right arrow key Adjusts the richness of the color.

Sharpness Press the button to sharpen or soften the picture. (Not available on PC and HDMI input .)

Tint Press the left/right arrow key to adjust tint. (Available for NTSC.)

Noise reduction Press the button to select off, low, mid, high to adjusts the dynamic noise reduction level of image.(Not available on PC and HDMI input .)

Color Temp Press left/right arrow key to change picture color temperature such as neutral, warm and cool .

-10-

Page 14

ANALOG MENU SCREENS

Sound menu

Installation menu

Enter Sound menu, you can select Sound Mode, Balance, Treble, Bass, Auto Volume Level. Items by pressing up/down arrow key.

Sound Mode Press the left/right arrow key to select the audio mode. The audio mode are Standard, Music, Film, Voice, Personal.

Balance Press the left/right arrow key to adjust to the left to right sound channel volume.

Treble Press the to adjust the high frequency signal value.

Bass Press the to adjust the bass boost value.

Auto Volume Level Press left/right arrow key to switch AVL function on/off. AVL function is not available except TV mode.

TV Speaker Press left/right arrow key to select speaker of sound output . When select Internal , sound is output from TV speaker , S/PDIF is mute : when select External , TV speaker is mute, S/PDIF is active as output for external speaker.

Enter Installation menu, you can search, and edit channel or favorite program by pressing up/down arrow key.

left/right arrow key

Language Press the left/right arrow key and MENU buttons to select the osd Language.

Channel Number You could change and display channel number you want.

CHANNEL NAME Display channel name, you could edit it if press "OK" to enter edit sub menu. use up/down arrow key to change name of program in the edit sub menu.

-11-

Page 15

ANALOG MENU SCREENS

Installation menu

Colour Sys Press the button to select a new colour standard value in TV. The choices are AUTO, PAL,NTSC and SECAM.

Sound Sys Press the button to select a new sound standard value in TV. The choices are B/G, D/K, I, M. It's

better to select it before auto installation.

Country Select country as your location, TV will make auto-sorting after auto installation, it's better to select it before auto installation.

Auto Installation Press right arrow key to start auto program search. TV will search all band for program.

Manual Installation Press right arrow key to start Manual program search . TV will search upward until one program found. You could input the program frequency directly to find program also if you know it.

Fine Tuning Press left/Right arrow key to decrease/increase current frequency step by step.

Organiser Press left arrow or OK key to enter sub menu, then you could use four color key to Delete, Copy, Move, Skip program in the list.

Favourite Channel Press left arrow or OK key to enter sub menu. There is 8 Favourite program which could be set . you could use left/right arrow key or digit number key to select favourite program.

-12-

Page 16

ANALOG MENU SCREENS

Time menu

Preferences menu

Enter Timer menu, you could set time and turn on/off timer. With Time reference, you could set channel from which TV get teletext time. Current Time show the time of your TV remember, you could set this time manualy if you want. Otherwise, TV get it from channel for time reference . Turn off/Wake up time used for setting of TV turn off and/or wake up time according current time. you could select which channel you want when the TV wake up according wake up time.

Enter preferences menu you can setup the Zoom, Film mode, OSD Transparent, Teletext char. Set.

Select preferences menu by press the up/down arrow key and enter the caption function by pressing left/right arrow key, you can adjust the Style function items by pressing left/right arrow key buttons.

Zoom The picture display will change as 4:3 format , 16:9 format , 14:9 zoom, 16:9 ZOOM1,16:9 ZOOM2 when you change Zoom setting.

Film Mode This option sets the file mode on or off .

OSD Transparent you could select different OSD background transparent by it . Setting it from 0 to 7.

Teletext char. Set you could select teletext character set by press left/right arrow key . it could be selected from 1 to 5 for character set West Eu. , East Eu. , Cyrillic , Turkey , Arabic.

-13-

Page 17

ANALOG MENU SCREENS

Parental Control menu

Enter Parental Control menu you can set control of it .Press left/right arrow key to select Parental Control item, then press up/down arrow key to entry menu.

Input correct password to entry sub menu when PIN item is high light . The initial password is "0000".

Lock Installation Press left/right arrow key to lock installation menu or unlock it. This item is only available in TV mode .

Channel Number Press left/right arrow key to select channel which you want lock. This item is only available in TV mode .

Lock Channel Press left/right arrow key to active channel lock function on or off. This item is only available in TV mode.

Lock Front panel Press left/right arrow key to lock front key board or not.

New PIN code/Repeat PIN code Input and double confirm new PIN code if you want have one new password.

-14-

Page 18

ANALOG MENU SCREENS

PC MODE

and LCD TV.

15 Pin Mini D-Sub Connector

PC Input typical display modes. The following table is an illustration of some of the typical video display modes.

1 640X480(recommend 60Hz)

2 800X600(recommend 60Hz) 3 1024X768(recommend 60Hz) 4 480p

5 576p 6 720p(50/60Hz) 7 1080i(50/60Hz)

MENU in PC Mode

Enter menu by pressing the "MENU" button on the remote control.

there are 4

,parental control)

same as in TV mode.

when you connect VGA cable to the jacks of PC or connect HD cable to device such as DVD, and select the signal source as "VGA" or "YPBPR" the screen menu will active. You can use the function to adjust the display setting automatically or manual.

H-Position Press left/right arrow key to adjust the H-Position of television the screen appear as . V-Position Press left/right arrow key to adjust the V-Position of television the screen appear as. Phase Press left/right arrow key to adjust the phase of the picture. This item is only available in VGA mode . Colck Press left/right arrow key to adjust the updating frequency of the picture. This item is only available in VGA mode . Auto Adjust Press left/right arrow key to auto adjust PC size and position. This item is only available in VGA mode .

geneal menus (Picture, Sound, Time

supported all functions are the

In PC mode state,

Geometry menu

PICTURE

-15-

Page 19

ANALOG MENU SCREENS

Preferences menu

Pip menu

Enter preferences menu you can setup the Language, Zoom, OSD Transparent.

Language Press the left/right arrow key and MENU buttons to select the osd Language.

Zoom The picture display will change as 4:3 format , 16:9 format , when you change Zoom setting.

OSD Transparent you could select different OSD background transparent by it. Setting it from 0 to 7.

Press up/down arrow key to select PIP item and press left arrow key to entry sub menu . PIP function is only avaiable in PC, HDTV, HDMI mode.

PIP Press left/right arrow key to switch on or off PIP function .

PIP Source Press left/right arrow key to select PIP source such as TV , AV.

Sound Press left/right arrow key to select TV sound from main or PIP channel.

PIP Size Press left/right arrow key to select PIP size such as 1 or 2 . 1 for small PIP picture, 2 for big PIP

-16-

Page 20

ANALOG MENU SCREENS

HDMI Input Resolutions

HDMI Input typical display Modes. The following table is an illustration of some of typical Video display modes.

1 640X480(recommend 60Hz)

2 800X600(recommend 60Hz) 3 1024X768(recommend 60Hz)

4 480p 5 576p 6 720p(50/60Hz)

7 1080i(50/60Hz) 8 1080p(50/60Hz)

Y Pb Pr Mode(Component input)

The menu of Y Pb Pr mode is exactly same as the menu of HDMI mode. YPbPr Input typical display modes. The following table is an illustration of some of the typical video display Modes.

1 480i 2 480p

3 576i 4 576p 5 720p(50/60Hz) 6 1080i(50/60Hz)

7 1080p(50/60Hz)

-17 -

Page 21

SERVICE TIPS

BEFORE CALLING FOR SERVICE, HAVE YOU CHECKED ( ) THE FOLLOWING CHART ON SYMPTOMS AND SOLUTIONS?

i t

Symptoms

No picture, no sound

Poor sound, picture OK

Poor picture, sound OK

Weak picture

Blurred picture

Double image

Lines in picture

Distorted picture

Weak reception on some channels

Horizontal bars

Picture rolls vertically

Poor colour

No colour

Misoperation of Remote control

No Remote control

On Screen Display Control outside the screen

Try

tatio

k o

bac

ire

l, i

r bro

t ae

k ae

-o

e c

h c

)

, e c

door ty

e f

s co

(

e n

bri

c t

ote

itc

c t

i s

ie r

n o

-18-