Http://www.lightskystar.com
PROFESSIONAL SHOW LIGHTING
LED MOVING-HEAD
USER MANUAL
GUANGZHOU LIGHTSTAR LIGHT CO.,LTD
THUNDER-60S
EN
I
Page1
EN
I
1.INDEX
2.Packing
Many thanks for choosing THUNDER-60S moving head.The
design&production are passed through the full quality
control to ensure the fineness ability.
This manual covers important information about install-
ation&operation of this projector.Please rsad this user manual
carefully before installing or operating this projector.Please do
follow the safety instruction.list as below carefully and keep this
manual in a safety place for future reference.
Note:As part of our ongoing commitment to continuos products
development,company will keep the right to improve this products,
the information in this menu may be changed in the future,the
company reserve the right to change the data without any advise.
2.1 The packing of the series of products is paper carton,the
flycase can order.
2.2 To open the carton
First please open the carton and take out the relative accessories,
Take out the projector from the polybad and put it on a very smooth
& horizontal surface place for the next operation.
Attention:Do not press the plastics parts to avoid any damage and
distortion.
2.3 Packing list
The following parts are packed
together with the projector:
Attachment
DMX cable 1pc
User manual 1pc
Moutnting Bracket 2pc
page2
EN
I
page7
3.Install and safe usage
3.1 Install the porjector:
3.1.1 Requirement for the installing place:
Please do ensure fasten the mount bracket firmly before installing.
The mount bracket must share the weight 10 multiple weight of the
projector`s.
3.1.2 The method of installstion and caution:
3.1.2.1 Connect the mount bracket well and fix the clamp firmly
to the truss in order to avoid the projector loose or falling.
3.1.2.2 The projector should be mounted via its clamp by using 2
bolts.The clamp itself attached tothe underside of the projector with
4 boltsprovided in the package. Always make sure that the projector
is anchored firmly to avoid any vibration or falling.
3.1.2.3 For safety the projector should have a secondary fixing with
a safety cord through the truss and the handle of projector.The safety
cord will fasten the projector on the truss tightly to avoid any vibration
or falling directly if the clamp or the truss is loose.
3.1.2.4 When in stalling the projector, not allow any person pass by,
3.1.2.5 After installing the light.Please inspect whether the safety
cord atrried,clamp or truss is loose in order to avoid the projector will
slip. If any dangers is happened by falling,the manufacturer won`t be
risponsible for it.
3.1.2.6 Other safety terms
3.1.2.6.1 Mininum distance between the projector`s shot&goal
project:
0.8M 2.0M
Picture 1
Picture 2
CHANNEL MENU:
NOP
NOP
S
EN
I
page3
page6
TECHNICAL PARAMETER:
VOLTAGE: AC90- 240V 50/60Hz
LIGHT SOURCE: 60W LED
POWER CONSUMPTION: 150W
BEAM ANGLE: 3°
1 COLOR WHEEL: 6 colors+open, half color effect, bi-directional
rainbow effect at variable speed
1 ROTATING GOBO WHEEL: 7 rotating gobos+open, bi-directionally
rainbow effect at variable speed
1 PRISM WHEEL: 3-facet prism, bi-directionally rotating, at variable
speed
DIMMER: 0~100% linearly adjustable
STROBE: 0.5~20 flash per second, speed adjustable
RANGE: Pan-540°, Tilt-270°(16-bit)
NET WEIGHT: 9KG
GROSS WEIGHT: 10.5KG
FIXTURE DIMENSION: L435×W250×H520(mm)
PACKING DIMENSION: L415×W345×H580(mm)
When fix the orientation of the projector. Please keep the minimum
distance between the flammable retarding subject and the porjector`s
shot is 0.8M at least.(Picture1) But the minimum distance between the
inflammable and the projector`s lens should be kept away 2m at least.
(Picture2).
3.1.2.6.2 The minimum distance between the inflaming retarding
subject and any other part of the light:
When fix the orientation of the projector.Please keep the minimum
distance between the inflaming retarding subject and the projector
shot is 0.3m at least.
3.1.2.6.3 MAX ambient temperature:
In order to ensure the light could operate normally, the ambient te-
mperature couldn`t be highter than33 degree and no lower than 2
degree.
3.1.2.6.4 Electric shock&static electricity portection:
These projectors are designed depends on the electric shock
protection, the projector should be connected when the power supply
is enough.The projector`s ground cable should be connected with the
ground cable of the power supply system as well.
3.1.2.6.5 Surface temperature:
Under normal condition,the highest sectional surface temperature
may be up to 90-120 degree.
3.1.2.6.6 Connct the main power supply:
Connecting the main power supply should be done by the professi-
onal person.
OPERATING MODE
DMX512Control Mode
The scanner DMX512 signal formats using 1-512 channel control.
Specific channel is set to ：
page4
LINE
EN
I
page5
1.DMX512 [address set]
This feature allows you to change device address value.
1, press the ESC key one or more, until the show "a. 001." At this time to press the
?UP" or "DOWN" will be the key to the It functions table.
2, press "ENTER", the letter "A" to put out, use "UP" or "DOWN" keys to select the
address value "001-512", Press "ENTER" confirm exit or press the "ESC button" give
up exit.
3. to accept the host synchronous (i.e. from machine model) the address value is
set for "001".
4, in the display address value condition, such as no DMX controller device connected,
the screen will flash, such as device to connect DMX control Implement, display will not
shine, and DMX signal for signal and flashing lights.
2、PAT1
SUAP----OFF Pan,Tilt normal
ON Pan,Tilt interchange
P,1NU----OFF Pan, foreward
ON Pan, inversion
T,1NU----OFF Tilt foreward
ON Tilt inversion
3、PTSP---- NORN
FAST
SLOU
4、PER5 DISP---ON : Display often ON
10S : Monitor doesn't operate 10 S shut
TURN---Monitor Positive and negative display
DRE5---ON,OFF
SCUT---ON,OFF Color design reset direction
5、DFSE----FACT----LOAD
6.INFO---Lamp software information and history
7,NAN----Automatic operation set
CH01:0--255
...........
CH12:0-255
8.TEST: Automatic operation mode, and as a MASTER advocate the lamp .
SOUN-----RUN sound control
AUTO--- -RUN Automatic control
9:REST:
3.1.2..6.6.1 Please check the voltage, frequency data of power sup-
ply system id suitable for the mentioned on the projector. Please do
avoid the different voltage between them and burn the projector.
3.1.2.6.6.2 Please refer to the actual wattage of the projector`s
lamp multiply 1.5 multiple multiply total quantity of the projector then
you could get the minimum power supply loading. Lf your power cable
can`t share the minimum power supply loading.Please don`t connect
all the porjectors meantiome.
Loading...