4. DVD Brands ............................................................................................................................. 98
4
www.skysat.bg
Precautions
1. Important Safety Instructions
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not reverse the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or third prong is provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
WARNING : To Prevent fire or shock hazard do not expose the set to rain or moisture.
2. Notice
These servicing instructions are for use by qualified service personnel only. To reduce the risk of
electric shock, do not perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
5
To reduce the risk of electric shock, do not remove
the cover (or back).
No user serviceable parts are inside.
Refer servicing to qualified service personnel.
The Lightning Flash with arrowhead symbol
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated "dangerous voltage" within the
product enclosure that may be of sufficient
magnitude to constitute a risk of shock to
persons
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and
maintenance (servicing) instructions
in the literature accompanying the
product
www.skysat.bg
The mains plug is used as the disconnect device. The disconnect device shall remain readily
operable.
3. Copyright
This manual is protected by copyright laws.
Copy, use and reproduction of this manual in part or whole without Manufacturer’s prior
written approval are prohibited.
4. Disclaimer
The manufacturers, distributors and agents are not liable to any kind of damage caused by
the use of the information contained in this manual.
The instruction and descriptions which this manual contains are based on the time of this
manual's production.
The manufacturer constantly updates it with new functions and technology.
All the specifications are subject to change without prior notice.
5. Trademarks
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
6
www.skysat.bg
Laboratories.
7
www.skysat.bg
Before You Begin
1. Main Features
For the feature of DVB-S/S2, Satellite tuner only
Supports MPEG4 /MPEG2 - HD/SD and Fully DVB-S2 /DVB-S Compliant
Intelligent Blind Scan for both SD and HD TV & Multi-Satellite Search
Multi-LNB Controlled by DiSEqC Control Version 1.0, 1.1, 1.2 and USALS
For the feature of DVB-C, Cable tuner only
Supports MPEG4 /MPEG2 - HD/SD and Fully DVB-C Compliant
For the feature of DVB-T, Terrestrial tuner only
Supports MPEG4 /MPEG2 - HD/SD and Fully DVB-T Compliant
For the feature of DVB-T2, Terrestrial tuner only
Supports MPEG4 /MPEG2 - HD/SD and Fully DVB-T2 Compliant
Common features for all types of DVB receivers
Twin Tuner HDTV PVR Receiver ( H.264/ MPEG4 HD )
Embedded Linux OS
Time Shifting, Recording & Playback with Internal HDD (SATA) / External HDD (E-SATA or
USB 2.0)
Simultaneously Records of 3 Services and allows Watching 2 others (PIP)
Powerful Extended EPG supports and Event Recording
Three USB 2.0 Host ports (MP3 Player & JPEG Viewer)
Xvid file play back supported
Ethernet port Supported
Premium Grade White VFD Display (12 Digit Alphanumeric)
Premium Grade Universal remote control unit
On-Screen Display with Full Color & Resolution
Favorite Groups
Powerful Service List Manager for Favorites, Lock, Skip, Move, Edit and Delete
Service Sorting by Alphabet, Transponder and CAS
User Friendly & Multi-language Supported (OSD & Menu)
Teletext / Subtitle Supported
Maximum 10,000 Services(TV & Radio) Programmable
Picture-in-Picture (PIP) & Multi-picture Display
Parental Lock / System Lock / Installation Lock
HDMI Video & Audio Output(576i, 576p, 720p, 1080i, 1080p)
Supports Y/Pb/Pr(component) Output in HD
CVBS(composite) Video & Audio Output via RCA
8
www.skysat.bg
CVBS, RGB, Y/C Video & Audio Output via TV SCART
Optical Output for Digital Audio(SPDIF)
Software & Service channel Database upgrade via USB & RS-232C port
2 Smart card reader and 2 Common Interface Slots
1W Stand-by Power Consumption
9
User's Manual
AAA size Batteries
X2
Loop through Cable
Remote Control
HDMI Cable
AC Power Cord
www.skysat.bg
2. Accessories
NOTE : If any accessories listed above are missing, contact the sales representative where you
purchased this unit.
10
www.skysat.bg
Hardware Description
1. Front Panel Configuration
1. POWER BUTTON : Press to switch between STANDBY and POWER ON modes.
2. Vol Up/Down BUTTON : Press to change audio volume in normal mode or to navigate menu
in menu mode.
3. CH Up/Down BUTTON : Press to change services in normal mode, or to move highlighted-
bar in menu mode.
4. Remote Sensor : Receives signal from remote controller.
5. VFD Display : The VFD consists of 12-digit letter. These letters display the current status of
receiver such as service name, service information and so on.
6. USB (Front) : Use it when connecting to external USB storage device.
7. SMART CARD READER : Insert smart card for encrypted service access.
8. PCMCIA : To receive other pay-tv service you need a CA-Module(Viaccess, Irdeto, Nagravison,
etc.) and a smart card from the service provider.
2. VFD(Vacuum Fluorescent Display)
1.Remote Indication LED : The LED lights on
when a key on the Remote Controller is pressed.
2.Information : Display information including
service name and other information.
11
Two tuners can be installed in different combination as follows.
For the professional installation of these tuners, please ask your local
agent or dealers for further assistance.
www.skysat.bg
3. Rear Panel Configuration
1. VCR SCART : Connects to the VCR or DVD using a VCR SCART cable.
2. TV SCART : Connects to the TV input using a TV SCART cable.
3. SPDIF : Connects to the audio system using a S/PDIF cable. (digital audio)
4. VIDEO : Connects to the TV or VCR using a RCA cable. (Composite video output / Yellow)
5. AUDIO L/R : Connects to the TV or VCR using a RCA cable. (Stereo audio output / White, Red)
6. Component : Connects to the TV or VCR using a component cable. ( YPbPr)
7. USB : Use it when connecting to external USB storage device.
8. HDMI : Connects to the TV by using a HDMI cable for the best quality picture and audio.
9. RS-232C : Serial port for firmware update and data transfer.
10. Ethernet : Local area network port for direct computer connection.
11. e-SATA : Connects to the external HDD via e-SATA cable.
12. A/C Switch : Power switch
12
www.skysat.bg
13. A/C power cable socket : Connects to A/C power cord.
13
www.skysat.bg
In case of S2 + S2
[ TUNER 1 ]
1.LNB IN (Caution : Socket on the left bottom)
Satellite broadcasting signal input socket for the first
tuner (TUNER 1). Connects a satellite antenna LNB
cable.
2.LNB OUT
Satellite broadcasting signal output socket through the
first tuner (TUNER 1). Connects to a second tuner
(TUNER 2) for loop-through.
[ TUNER 2 ]
3.LNB IN (Caution : Socket on the right bottom)
Satellite broadcasting signal input socket for the second tuner (TUNER 2). Connects a satellite
antenna cable or from the first tuner (TUNER 1) LNB OUT connector.
4.LNB OUT
Satellite broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
In case of T(T2) + T(T2)
[ TUNER 1 ]
1.ANT IN
Terrestrial broadcasting signal input socket for the first
tuner (TUNER 1). Connects an aerial antenna.
2.LOOP OUT
Terrestrial broadcasting signal output socket through
the first tuner (TUNER 1). Connects to second tuner
(TUNER 2) for loop-through.
[ TUNER 2 ]
3.ANT IN
Terrestrial broadcasting signal input socket for the
second tuner (TUNER 2). Connects a aerial antenna cable or loop-through cable from the first
tuner (TUNER 1).
4.LOOP OUT
Terrestrial broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
In case of C + C
[ TUNER 1 ]
1.CABLE IN
Cable broadcasting signal input socket for the first
tuner (TUNER 1). Connects a cable antenna.
2.CABLE OUT
Cable broadcasting signal output socket through the
first tuner (TUNER 1). Connects to second tuner (TUNER
2) for loop-through.
[ TUNER 2 ]
3. CABLE IN
14
www.skysat.bg
Cable broadcasting signal input socket for the second tuner (TUNER 2). Connects a cable
antenna or loop-through cable from the first tuner (TUNER 1).
4.
CABLE OUT
Cable broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
15
www.skysat.bg
In case of S2 + T(T2)
[ TUNER 1 ]
1.LNB IN (Caution : Socket on the left bottom)
Satellite broadcasting signal input socket for the first
tuner (TUNER 1). Connects a satellite antenna LNB
cable.
2.LNB OUT
Satellite broadcasting signal output socket through the
first tuner (TUNER 1). Connects to another STB for
loop-through.
[ TUNER 2 ]
1.ANT IN
Terrestrial broadcasting signal input socket for the
second tuner (TUNER 2). Connects a aerial antenna cable.
2.LOOP OUT
Terrestrial broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
In case of S2 + C
[ TUNER 1 ]
1.LNB IN (Caution : Socket on the left bottom)
Satellite broadcasting signal input socket for the first
tuner (TUNER 1). Connects a satellite antenna LNB
cable.
2.LNB OUT
Satellite broadcasting signal output socket through the
first tuner (TUNER 1). Connects to another STB for
loop-through.
[ TUNER 2 ]
3.CABLE IN
Cable broadcasting signal input socket for the second
tuner (TUNER 2). Connects a cable antenna.
4.CABLE OUT
Cable broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
In case of T(T2) + C
[ TUNER 1 ]
1.ANT IN
Terrestrial broadcasting signal input socket for the first
tuner (TUNER 1). Connects a aerial antenna.
2.LOOP OUT
Terrestrial broadcasting signal output socket through
the first tuner. Connects to another STB for loopthrough signal.
[ TUNER 2 ]
3. CABLE IN
16
www.skysat.bg
Cable broadcasting signal input socket for the second tuner (TUNER 2). Connects a cable
antenna.
4.CABLE OUT
Cable broadcasting signal output socket through the second tuner (TUNER 2). Connects to
another STB for loop-through.
17
www.skysat.bg
4. Remote Control Unit
1. POWER : Turns the STB On/Off.
2. MUTE : Turns the sound On/Off.
3. Universal Buttons
a. Universal TV : Change the TV Remote Controller.
b. STB : Change the STB Remote Controller.
c. Universal DVD : Change the DVD Remote Controller.
4. MODE
a. V.Format : You can switch the Display Format (4:3 / 16:9)
b. Sleep : To adjust sleep timer.
c. TV/RADIO : Switches between TV and Radio.
d. Resolution : To select the resolution format. Each time you press the Resolution button, the
resolution changes in the following sequence: 576i > 576p > 720p > 1080i > 1080p
5. Playback Control Buttons
a.Rewind : Rewinds at high speed. Each time you press this button the rewind speed is
increased.
b.Fast Forward : Fasts forward at high speed. Each time you press this button the speed is
increased.
c.Previous File : To play the previous MP3 file in MP3 play mode. This button is also used to
jump back to beginning of recording during a playback.
d.Next File : To play the next file. This button is also used to jump to end of recording during a
playback.
e.Play / Time shift : Display the progress bar of playback when no progress bar is displayed.
Start playback with normal speed. Return to normal speed from trick mode..
f. Recording : To start Recording.
g. Repetition (*): This key is used to play back a recording repeatedly.
h. Pause : This key is used to pause the video. Press once more to resume the video.
18
www.skysat.bg
i. STOP : To stop time shifting, play back or recording.
NOTE : (*) This button(Repetition) will be supported later, by new s/w version by upgrading.
Please refer to your local dealer / distributor.
19
www.skysat.bg
6. Color Buttons
a.RED : Used for special function in menu. RED key is used to sort lists in service list or go to
previous day search in EPG or make/delete the current position as a bookmark.
b.GREEN : Used for special function in menu. GREEN key is used to set favorites setting in
service list or go to the next bookmark position.
c.YELLOW : Used for special function in menu. YELLOW key is used to find service in service
list or change the audio track.
d.BLUE : Used for special function in menu. BLUE key is used to set service list option in service
list or display Multi-Picture.
7.Information : Shows the information box of the current program. If you press one more time, a
detail information box will be shown.
8. Recall : Moves to previous service.
9. ARROW Buttons
a.Up & Down Key : To change the value of a selected item with preprogrammed values in
menu.
b. Left & Right Buttons : To move the cursor left and right in menu.
10. OK or Service List : Show the service list in non-menu mode and select an item or confirm in
menu mode.
11. Menu : To enter the main menu or to move to the previous menu.
12. EXIT : Exit from the menu or pop-up window.
13. Page Up& Down : Move to the next or previous page if more than one page is available. This
button also is change the location of sub picture in PIP.
14.Favorite : To display the satellites programmed into the receiver and the favorite groups.
20
www.skysat.bg
21
www.skysat.bg
15. Volume Up & Down : To change the Volume.
16. Channel Up & Down: To change the TV or Radio service channel.
17. EPG(Electronic Program Guide) : Show the TV/Radio program guide.
18. Play List : To show the file list in the SATA HDD or USB Storage Device.
19. PIP Buttons
a. PIP(Picture in Picture) : To open the PIP window.
b. PIP Swap : Switching between main-picture and sub-picture
c. PIP(Picture in Picture) Service List : To shown the sub-picture service list.
20. Numeric : Controls the numerical operation and service numbers directly.
21. Subtitle : To show multilingual subtitle.
22. Teletext : To show the digital teletext.
22
www.skysat.bg
5. Multi-Brand IR Remote Controller Setting
NOTE : When there is no input during about 10 seconds from set mode, set mode is
canceled.
1. Direct Code Entry
Step 1 : Turn on the DEVICE what you want to set up(TV / DVD / VCR)
Step 2 : Press DEVICE and OK button during about 2 seconds at the same time.
DEVICE LED will blink twice.
Step 3 : Input the 3 digit code numbers.
(Refer to ‘Code Table for Universal Remote Control Unit’ in the rear section of this
manual)
DEVICE LED will blink twice and the DEVICE turns off.
If you enter a wrong DEVICE code, DEVICE will blink once
Step 4 : If your DEVICE turns off, press OK button.
DEVICE LED will blink twice.
2. Auto Code Search
Step 1 : Turn on the DEVICE what you want to set up(TV, DVD)
Step 2 : Press DEVICE and OK buttons during about 2 seconds at the same time.
DEVICE LED will blink twice.
Step 3 : Press UP or Down button within 10 seconds to enter the Search mode.
Step 4 : Press UP or Down button until the DEVICE turns off, one and one.
Step 5 : If your DEVICE turns off, press OK button.
DEVICE LED will blink twice.
3. Code No. Checking (Number Call)
Step 1 : Press DEVICE and OK buttons during about 2 seconds at the same time.
DEVICE LED will blink twice.
Step 2 : Press INFO button within 3 seconds.
LED will blink according to inputted mode number on the device.
( Case of digit '0', it blinks 10 times.)
23
www.skysat.bg
Connecting diagram
1. Receiver to A/C power
Connect the A/C power cord between A/C power cord socket of receiver and A/C outlet.
2. Receiver to TV with Digital A/V Output
Connect the HDMI Cable to the HDMI Connector of the TV.
Connect SPDIF to Digital audio input of the equipment(Digital Audio)
NOTE : Depending on the A/V equipment you own, there are various ways you can connect
the STB. To choose the best connection option, please refer to the manual of the
equipment you would like to connect to. To get High Definition playback of High
Definition content, we recommend that you connect your high definition display
with a HDMI cable. HDMI supports standard, enhanced or high-definition video
24
www.skysat.bg
and multichannel audio in a single cable.
25
www.skysat.bg
3. Receiver to TV with Analog A/V Output
Connect the TV SCART to the SCART input of the TV.
Connect the Component to the Component input of the TV.
Connect the RCA to the RCA input of the TV.
NOTE : The component connection(YPbPr) is recommended for Digital TV.
The SCART cable connection is recommended for analogue TV or VCR
The composite connection(RCA cable) is recommended for analogue TV
You cannot view high definition video with the SCART and the composite video
connector.
26
www.skysat.bg
4. Receiver to TV and VCR
Connect the TV SCART to the SCART input of the TV.
Connect the VCR SCART to the SCART input of the VCR.
27
www.skysat.bg
5. Connecting to Antenna Cable
5.1 In case of S2 + S2 (Satellite + Satellite) tuners
Connecting one dish to both tuners by Loop through
Connecting each Dish to each Tuner
Connecting Antenna cable to each Tuner using DiSEqC SW (Recommend)
28
www.skysat.bg
5.2 In case of T(T2) + T(T2) (Terrestrial + Terrestrial) tuners
Connecting one aerial antenna to both tuners by Loop through
Connecting two aerial antenna to each Tuner
5.3 In case of C + C (Cable + Cable) tuners
Connecting one broadcasting cable to both tuners by Loop through
Connecting two broadcasting cable to each Tuner
29
www.skysat.bg
5.4 In case of S2 + T(T2) (Satellite + Terrestrial) tuners
Connecting dish antenna to LNB IN of the tuner
Connecting aerial antenna to ANT IN of the Tuner
5.5 In case of S2 + C (Satellite + Cable) tuners
Connecting dish antenna to LNB IN of the tuner
Connecting broadcasting cable to CABLE IN of the Tuner
5.6 In case of T(T2) + C (Terrestrial + Cable) tuners
Connecting aerial antenna to ANT IN of the Tuner
Connecting broadcasting cable to CABLE IN of the Tuner
30
Loading...
+ 79 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.