Skyrocket Toys 01598RX24G, 01598TX24G User Manual
01598
NANO DRONE
POWERING UP AND PAIRING ( WITH ALTITUDE ON)
ONOFF
FLYING GUIDE
Turn on drone. Turn on remote. Wait for flashing green lights t o turn solid.
Place drone on flat surface.
FLYING BASICS
1 2
Press Auto Launch to launch a few feet off the ground.
3 4
Press the directional Thumbstick to fly in any dir ection.
Press the Altitude butt on to fly approximatel y 12” higher or lower.
Press the Auto Land button to land.
TOGGLE INTO MANUAL FLIGHT BEFORE TAKE-OFF
• Hold stunt button and press auto land/auto launch butt on
and a tone will sound from the remote. Make sure your
throttle stick is in the down position.
• Push the t hrottle stick up to begin manual flight.
TOGGLE INTO MANUAL FLIGHT WHILE IN AUTO -HOVER
• Hold stunt button and press auto land/auto launch butt on
and a tone will sound from the remote. Make sure your
throttle stick is in the down position.
• Aft er the t one is heard, move the throt tle stick up until
the drone start s to rise. (If throttle is not matched in
5 seconds then manual flight will be cancelled.)
TOGGLE INTO AUTO HOVER WHILE IN MANUAL FLIGHT
• Press either the up or down altitude lock ing button to
toggle back into aut o hover. (Your drone will hover at the
current throttle.)
FLIGHT CONTROLS
THROTTLE/ ROTATION STICK
• While in manual flight mode push the throt tle
stick forward to make drone lif t.
• The fur ther you push t he throttle stick, the
fast er you lift.
Pres s up
to lif t
Pres s down
to descend
Pres s lef t
to ro tat e
counterclockwise
Pres s righ t
to ro tat e
clockwise
ALTITUDE BUTTONS
• Press the up or down arr ow to adjust
the drone’s altitude. The drone will lif t
or lower approx imately 12” each time
the up or down arr ow is pressed.
(Distance may vary.)
• Hold the up or down buttons for
continuous lift or descent.
Up and down controls only apply to manual
(
flight mode.
Power O n/off Swi tch/sensi tiv ity Swit ch
Stun t But ton
THROTTLE/
ROTATION STICK
Rota tion Trim
FLYING TIPS
• When launching the drone, face the same
DIRECTION STICK
• Push the direction st ick forward to fly for ward or
away from you (Green blade in front). Push
backwards t o fly backward. The further you push,
the faster the drone will fly in that direction.
• Push the direction st ick left to fly left. Push right
(
to fly right. The further you push, the faster
the drone will fly sideways.
Forward/Backwar d Trim
Power i ndica tor LED
DIRECTION STICK
Lef t/Right Trim
AUTO L AUNCH /LAND BUT TON
• Press the auto launch
button to launch a few feet
from t he ground.
(Exact height may vary.)
• Press the auto land bu tt on
to land the drone by itself.
Pres s up to
fly forward
Pres s down
to fl y
backward
Pres s lef t
to fl y lef t
Pres s righ t
to fl y righ t
direction as the drone. Green blades and green
LEDs should be in front.
• If your drone drif ts in any direction when you ar e
hovering, you will need to make Trim
adjustments to correct the driving. Trim
adjustments are sometimes needed when the
drone is f irst flown aft er purchase. See TRIM
ADJUSTMENTS section for details.
• Practice launching, hovering and landing befor e
attempting to learn other moves.
• Flying 2 t o 3 feet above the ground will reduce
ground turbulence and make flying easier.
• When first at tempting to fly in different
directions, star t by tapping the direction stick
until you have a feel for it. Always move controls
slowly until you become comfortable operating
the drone.
• Once you’ve mastered flying in dir ections,
practice rotational controls. Spinning and
keeping drone facing the same direction as you
makes fl ying easier and more intui tive.
• Stay 2 to 3 feet away from walls and ceilings
as drone will be draw n towards them if you fly
too close.
• If propeller blades come in cont act with
another object or you crash, throt tle down or
auto land immediately to prevent possible or
further damage.
• If anyt hing prevents drone’s blades from
spinning or they become jammed, throttle
down or auto land immediately. Do not at tempt
to fly until obstruction has been removed and
damage fixed.
• Should something prevent dr one’s blades from
spinning, drone may aut o shutdown. LiPo
battery will need to be unplugged then
reconnected to res tore flying power.
FLIGHT SENSITIVIT Y SWITCH
The Drone’s responsiveness may be adjusted on the Controller to match your flying skills.
There are three choices: 1 LOW sensitivity 2 HIGH sensitivit y
It is best to start in the low sensitivity position until you have mastered fly ing. Flight sensitivit y
can be adjusted before or during flight.
LOW
2
1
OFF
HIGH
2
1
OFF
• If the drone flies too far away, beyond the
contr ol range of the remote, the drone will
auto-land to prevent the drone from flying away
out of control.
Online Video
Instructions & Flying
Tips available now at
SKY VIPER.COM
+ AAA/LR 03/R03 1.5V –
+ AAA/LR 03/R03 1.5V –
– AAA/LR 03/R03 1.5V +
TRIM ADJUSTMENTS
If the drone drifts in any direction while hovering (and you are not pressing the direction stick), you may need to make trim adjustments.
Press the recommended trim but ton as described below to make adjustments.
Tip 1: When the remote LED flashes 3 times quickly, the trim will revert back to middle of trim range.
Tip 2: If you are uncomfor table trimming the drone in flight, you can land onto a flat surface and make your trim adjustments.
If the dr one drifts forward
– Press B button
TROUBLESHOOTING
PROBLEM SOLUTION
Drone drifts in any
direc tion during flight
without direct ion fr om
the remote
All blades spin, but drone
will not fly properly or
crashes immediately
If the dr one drifts backwar ds
– Press F button
If the dr one drifts left
– Press R button
• Adjust the trim contr ols until drifting ceases.
• Drone’s blade may have been installed incorrectly. Reinstall and
remember that the GREEN blades point forward.
If the dr one drifts right
– Press L button
If the dr one spins counter-clockwise,
when viewed from t he top
– Press button
ONE TOUCH STUNTS
BARREL ROLL
While flying forward (or reverse),
tap the stunt button.
NOTE:
Trim adjustments will remain saved unt il remotes batteries
are removed.
If the dr one spins clockwise,
when viewed from t he top
– Press button
NOTE:
Once a stunt has been initiated, DO NOT adjust Throttle or pr ess
any other controls until the stunt has been completed.
Drone is
unresponsive
• Ensure the remote has fresh batteries and the LiPo battery is
fully charged.
• Drone may be miscalibrated by launching fr om an un-level surface. Turn
the remote off. Turn off the drone then turn them back on and try again
from a f lat, level launching surface.
Drone crashes when
att empting stunt
functions
• Inspect drone for any possible damage.
• Ensure that drone is flying a minimum distance of 6 feet from the
ground w ith a minimum 6 feet clearance in all directions.
FLIP
1 Bring the drone t o a mid-air
ADULT SUPERVISION REQUIRED
Befor e each use, an adult should check this produc t and the LiPo bat ter y to ensure no damage or
hazards exist. Drone has rotating blades that move at high speed, posing danger of damage and injury.
Pilots are responsible for any actions that result in damage or injur y from the improper operation of
drone. Adequate fly ing space is required. Avoid flying near interior fans and/or vents as they may make
flying dif ficult to control. Keep a safe distance away from streets, public thoroughfares and power lines.
Never attempt to r etrieve drone from any location higher than your reach (such as rooftops or trees)
or from any location that poses a safety hazard. Never fly drone at night. Keep dr one in sight at all
times during operation. Discontinue operation immediately if drone flies out of your field of view. Do not
fly near spectators or animals. Pets can become excited about R/C vehicles therefore keep away from
pets at all times. Keep spinning rotors away f rom fingers, hair, eyes and other body par ts. Always
launch from a flat surface. Never leave drone unattended while it is turned on. Read all enclosed
information before operating.
CAUTION!
The drone should be flying at least 6 feet in the air wit h a minimum clearance of 6 feet in all directions
before attempting stunt functions.
CONTENTS REMOTE BATTERIES
hover without flying in any
direc tion. Remove finger
from t he direction stick.
2 While hovering, tap and
hold the stunt button.
3 Then quickly t ap the
direc tion s tick in the
direc tion you want t he
drone to flip.
• Nano Drone
• USB Charging Cable
• Remote Control
• 4 Replacement Blades
Loosen the screw in
the Remote Control
battery compar tment
door wi th a Phillips
screwdriver and insert
3 x1.5 V AAA (LR03)
batteries as shown.
Replace door and
tighten screw.
CHARGING THE DRONE
CHARGING PRECAUTIONS:
• Aft er use, allow drone (battery on bot tom) to cool down
O
N
F
F
O
ON
OFF
Charging cord Plug in USB cableTurn on drone.
1 Turn drone of f.
Connect charging
cord to plug on dr ome.
THIS PROD UCT CONTAINS A LITHIU M-POLYMER BATTERY 3.7V 100 mAh:
LiPo batt eries have a severe ris k of fire and injur y if they are improp erly handled or m isused. They may e xplode, overhe at or ignite. Read all f ollowing prec autions and instr uctions regard ing
the care an d use of LiPo batter ies.
The buil t-in LiPo batter y is only to be used wit h the drone and charg er included with t his product.
• Keep away fro m flammable mat erials.
• Do not exp ose to direct sunl ight.
• Do not place i n fires or leave in ho t places.
• Do not drop o r make subject to str ong impact.
• Keep dry a nd away from water.
LiPo Batt ery Disposal : LiPo batterie s must be recycl ed or disposed of p roperly. They shou ld not be dispose d of with other hous ehold waste. Che ck your local laws an d regulations for co rrect
ALKALINE BATTERY CAUTIONS
• Do not use re chargeable bat teries.
• Diffe rent types of bat teries or new and o ld batteries ar e not to be mixed.
• Batteri es are to be insert ed using correct p olarity.
WARNING : Batteries ar e harmful if swall owed. Please keep a way from children .
Batter y Disposal : Dispose of batte ries according to th e local laws and re gulations of your re gion. Some bat teries may be rec ycled, and may be acce pted for disposa l at your local rec ycling
centre. If yo u are not able to iden tify the appli cable rules in you r area, please che ck the instruct ions of the batter y manufactur er.
recycl ing and/or bat tery disposa l.
2 Plug charging cor d
into computer or
USB power block.
3 Red light = charging
Green light = fully charged
• Remove exh austed batter ies as soon as possib le and discard pro perly.
• Remove all b atteries from th e compartment i f toy is not used for a lon g period.
• The suppl y terminals are not to b e short circuit ed.
• Never throw b atteries in a fi re or attempt to ope n outer casing.
• Remove exh austed batter ies as soon as possib le and discard pro perly.
• Remove all b atteries from co mpartment if toy i s not used for a long p eriod.
• Never throw b atteries in a fi re or attempt to ope n the outer casing .
to room temperature bef ore charging again.
• Charge drone in an isolat ed area, away from excessive
heat or moisture.
• If you suspect that the battery is damaged or swelling,
turn off the drone immediately.
• Do not modify, heat, or wet the battery in any way. Only
recharge with provided charger.
This devi ce complies with PART 15 of the FCC Ru les. Operatio n is subject to the
followi ng two condition s. (1) This device may not c ause harmful inter ference, and
(2) this de vice must accept any in terference re ceived, includin g interferenc e that
may cause un desired opera tion.
CAUTIO N: Changes or mo difications t o this unit not expre ssly approved by the
part y responsible fo r compliance could vo id the user’s autho rity to operate t he
equipment.
NOTE: T his equipment has b een tested and fo und to comply with th e limits for a
Class B digi tal device, pursu ant to Part 15 of the FCC Rules. T hese limits are
designed to provide reasonable protection against harmful interference in a
resident ial installatio n. This equipme nt generates, use s and can radiate ra dio
freque ncy energy and , if not installed a nd used in accordan ce with the instruc tions,
may cause ha rmful interfe rence to radio commu nications. Howe ver, there is no
guarante e that interfere nce will not occur in a p articular ins tallation. If thi s
equipm ent does cause harm ful interfere nce to radio or telev ision reception , which
can be det ermined by turnin g the equipment of f and on, the user i s encouraged to
try to cor rect the inter ference by one or mo re of the following m easures: Reo rient
or reloc ate the receiving a ntenna - Increase th e separation be tween the equi pment
and recei ver - Connect the e quipment into an out let on a circuit dif ferent from tha t
to which the r eceiver is connec ted - Consult the de aler or an experi enced radio/ TV
technician for help.
Remove all p ackaging att achments befo re giving the toy to a chi ld.
Not suita ble for children u nder 3 years due to sma ll parts that coul d be swallowed.
Conforms t o product safe ty standards A STM F963.
Keep inst ructions for fu ture reference. D o not discard.
©2016 Skyrocket Toys LLC , Los Angeles CA 90 066 USA. All Rig hts Reserved . Sky
Viper an d Skyrocket an d their respect ive logos are trad emarks and/ or
registe red trademark s of Skyrocket Toys LLC . All other trade marks, logos an d
copyrig hts are the proper ty of their resp ective owner s, and there is no
relationship express or implied with Skyrocket Toys LLC.
MADE IN CHI NA
The sof tware included in this product contains copyrighted
software that is licensed under the GPLv3. A copy of that
license is included in our websit e at the URL below. You may
obtain the complete Corresponding Source code from us for
a period of three year s after our last shipment of t his
product and/or spare par ts therefor, which will be no
earlier than 05-01-2019, on our website at
http://www.skyrockettoys.com/GPL/
®
Loading...