Art Release for Production (Mechanical)
Sky Instructions Domestic
File Name: SV_Nano_Drone_IS_050215_F1.ai
Revision:
Licensor Approval Date:
Production Release Date: 05/02/15
Production Artist: Hanjin Park
Colors: Pantone 294
Trim Size:
Notes:
TROUBLESHOOTING
PROBLEM SOLUTION
Drone is unresponsive or
behaving erratically
All blades spin, but Drone
will not y properly
Drone drifts in any
direction during ight
without direction from the
remote
Drone crashes
immediately
• Drone may be miscalibrated by launching from an unlevel
surface. Turn the remote off. Turn off the Drone for 30
seconds, then turn them back on and try again from a at,
level launching surface.
•
Ensure your remote is within unobstructed view of Drone and
you are within 30 feet range.
•
Ensure the remote has fresh batteries and the LiPo battery
is fully charged.
•
Inspect Drone for any possible damage. Turn the remote off
and turn off the Drone for 30 seconds then turn them back
on and try again from a at, level launching surface.
•
Drone’s blade may have been installed incorrectly. Reinstall
and remember that the GREEN blades point forward.
Adjust the trim controls until drifting ceases, see page 7.
•
•
Propellers may be installed in the wrong position. Ensure
proper installation.
200
200
INSTRUCTION GUIDE
CONTENTS
Remote Control
RC Nano Drone
12
Drone crashes when
attempting stunt functions
www.skyrockettoys.com/products/sky-viper
Customer Service :
888-674-5650
©2015 Skyrocket Toys LLC, Los Angeles, CA 90066 USA. All Rights Reserved.
Sky Viper is a registered tradmark and the Skyrocket logo are trademarks of Skyrocket Toys LLC.
1A
• Ensure that Drone is ying a minimum distance of 6 feet
from the ground with a minimum 6 feet clearance in all
directions.
#skyviper#skyviper
™
MADE IN CHINA.
4 Replacement Blades
USB Charging Cable
Remove all packaging attachments before giving the toy to a child.
Not suitable for children under 3 years due to small parts that could be swallowed.
Conforms to product safety standards ASTM F963.
Keep instructions for future reference. Do not discard.
This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help.
™
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
BACK COVER / FRONT COVER
ADULT SUPERVISION REQUIRED
CHANGING DAMAGED PROPELLERS
Before each use, an adult should check this product and the LiPo battery to ensure no damage or
hazards exist. Drone has rotating blades that move at high speed, posing danger of damage
and injury. Pilots are responsible for any actions that result in damage or injury from the improper
operation of Drone. Adequate ying space is required. Avoid ying near interior fans and/or vents as
they may make ying difcult to control. Keep a safe distance away from streets, public thoroughfares
and power lines. Never attempt to retrieve Drone from any location higher than your reach (such as
rooftops or trees) or from any location that poses a safety hazard. Never y Drone at night. Keep
Drone in sight at all times during operation. Discontinue operation immediately if Drone ies out of
your eld of view. Do not y near spectators or animals. Pets can become excited about R/C vehicles
therefore keep away from pets at all times. Keep spinning rotors away from ngers, hair, eyes and
other body parts. Always launch from a at surface. Never leave Drone unattended while it is turned
on. Read all enclosed information before operating.
THIS PRODUCT CONTAINS A LITHIUM-POLYMER BATTERY3.7V 100mAH:
LiPo batteries have a severe risk of re and injury if they are improperly handled or misused. They may explode,
overheat or ignite.Read all following precautions and instructions regarding the care and use of LiPo batteries.
The built-in LiPo battery is only to be used with the vehicle and charger included with this product.
• Keep away from ammable materials.
• Do not expose to direct sunlight.
• Do not place in res or leave in hot places.
• Do not drop or make subject to strong impact.
• Keep dry and away from water.
• Remove exhausted batteries as soon as possible and discard properly.
• Remove all batteries from the compartment if toy is not used for a long period.
• The supply terminals are not to be short circuited.
• Never throw batteries in a re or attempt to open outer casing.
LiPo Battery Disposal: LiPo batteries must be recycled or disposed of properly. They should not be disposed
of with other household waste. Check your local laws and regulations for correct recycling and/or battery disposal.
1 Turn off the Nano Drone.
2 Make note of the blade color and
letter (A or B) before removing the
blade from Drone.
(Markings are located on the
underside of blades and Drone).
3 Pull up on the damaged blade
to remove.
4 Press on a new blade.
3
4
GREEN
BLADES
B A
FRONT
BACK
A B
BLACK
BLADES
Bottom View of Nano Drone
WARNING: Do not y with broken or
damaged propeller blades as it may
cause damage or lead to injury.
ALKALINE BATTERY CAUTIONS
• Do not use rechargeable batteries.
• Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and old batteries are not to be mixed.
• Batteries are to be inserted using correct polarity.
• Remove exhausted batteries as soon as possible and discard properly.
• Remove all batteries from compartment if toy is not used for a long period.
• The supply terminals are not to be short-circuited.
• Never throw batteries in a re or attempt to open the outer casing.
WARNING:Batteries are harmful if swallowed. Please keep away from children.
Battery Disposal: Dispose of batteries according to the local laws and regulations of your region. Some batteries
may be recycled, and may be accepted for disposal at your local recycling center. If you are not able to identify the
applicable rules in your area, please check the instructions of the battery manufacturer.
WHEN the top shell comes up
after crash:
• Snap back into place using clips.
1
MAINTENANCE
• Over time loose hair or carpet bers might get wound in propellers, reducing
performance. Turn off the Drone and remove bers from motors.
(Remove blades if necessary).
2
1 10
1B
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 1 / PAGE 10
OFF ON
ONE TOUCH STUNTS
BARREL ROLL
While ying forward (or reverse),
press the STUNT BUTTON.
NOTE: Once a stunt has been initiated,
DO NOT adjust Throttle or press any other
controls until the stunt has been completed).
1
2
CHARGING & CARING FOR LIPO BATTERY
IN THE Drone
1 Turn OFF Remote Control & Drone.
2 Plug small end of the CHARGING CORD into the back of
the Drone.
3 Plug the large end of the CHARGING CORD into a
computer or USB power block.
RED LIGHT = CHARGING
GREEN LIGHT = FULLY CHARGED
4 Charge battery until full.
1
5 Once charged, unplug the large end of the CHARGING
CORD from the USB port.
FRONT BARREL ROLL
FLIP
1 Bring the Drone to a mid air hover without ying in any
direction. Remove nger from the DIRECTION STICK
2 While HOVERING,
3 While still holding the
STICK in the direction you want to the drone to ip.
RIGHT FLIP LEFT FLIP
FRONT FLIP
press and hold the STUNT BUTTON.
STUNT BUTTON,
tap the DIRECTION
BACK FLIP
REAR BARREL ROLL
1
6 Unplug small end of the CHARGING CORD from the back
of the Drone.
NOTE:
Always turn OFF the Drone when not in use.
CHARGING PRECAUTIONS:
After use, allow Drone (battery on bottom) to cool down to
room temperature before charging again.
•
Charge Drone in an isolated area, away from excessive
heat or moisture.
•
If you suspect that the battery is damaged or swelling,
turn off the drone immediately.
•
Do not modify, heat, or wet the battery in any way. Only
recharge with provided charger.
2
3
CHARGING
CORD
2
3
CAUTION!
Drone should be ying at least 6 feet in the air with a minimum clearance of 6 feet in all
directions before attempting stunt functions.
9 2
2A
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 9 / PAGE 2
+ AAA/LR03/R03 1.5V –
+ AAA/LR03/R03 1.5V –
– AAA/LR03/R03 1.5V +
INSTALLING REMOTE BATTERIES
FLYING TIPS
Loosen screw in the Remote Control battery
compartment door with Philips screw driver and
insert batteries as shown. Replace door and
tighten screw.
3 x
1.5 V
+
AA A (LR03)
1.5 V
–
AA A (LR03)
1.5 V
+
AA A (LR03)
WHEN NOT IN USE:
• Always turn OFF the Remote Control and the
Drone, when not in use or when being stored
or transported.
• Store the Remote Control and Drone in a dry
area at room temperature.
• Avoid temperatures less than 40°F/4°C and
greater than 120°F/49°C.
• Do not leave the Remote Control or Drone in
a car or exposed to direct sunlight. If
exposed to temperatures greater than
120°F/49°C, the Remote Control or Drone
batteries can be damaged or may catch
re.
–
+
–
• When launching the Drone, face the same direction as the Drone. Green blades and
Green LEDs should be in front.
• Practice launching, hovering and landing before attempting to learn other moves.
• Flying 2 to 3 feet above the ground will reduce ground turbulence and make ying
easier.
• When rst attempting to y in different directions, start by tapping the Direction stick
until you have a feel for it. Always move controls slowly until you become comfortable
operating the Drone.
• Once you’ve mastered ying in directions, practice Rotational controls. Spinning and
keeping Drone facing the same direction you are facing makes ying easier and more
intuitive.
• Stay 2 to 3 feet away from walls and ceilings as Drone will be drawn towards them if
you y too close.
• If propeller blades come in contact with another object or you crash, throttle down
immediately to prevent possible or further damage.
OFF
ONOFF
• If anything prevents Drone’s blades from spinning or they become jammed, THROTTLE
DOWN IMMEDIATELY. Do not attempt to y until obstruction has been removed and
damage xed.
• Should something prevent Drone’s blades from spinning, Drone may AUTO
SHUTDOWN. The Drone will need to be turned off, then back on, to restore ying
power.
• If the Drone ies too far away, beyond the control range of the remote, the Drone will
AUTO-LAND to prevent the Drone from ying away out of control.
AUTO SHUTDOWN:
• If battery voltage drops to an extremely low level, Drone will
automatically shutdown. The Nano Drone will need to be recharged to
restore ying power.
• If anything prevents Drone’s blades from spinning or they become
jammed, Drone will automatically shutdown. To restore ying power, turn
OFF the Drone and then turn it ON again.
• Occasionally, check that the two halves of the Drone body are not separating. If they
are, simply press gently and snap them back together.
3 8
2B
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 3 / PAGE 8
OFF
FLIGHT SENSITIVITY ADJUSTMENT
CALIBRATING & LAUNCHING
Drone responsiveness may be adjusted on the Controller
to match your ying skills.
There are two choices:
1- LOW SENSITIVITY 2– HIGH SENSITIVITY
It is best to start in the LOW SENSITIVITY position
until you have mastered ying.
Flight sensitivity can be adjusted before or during ight.
TRIM ADJUSTMENTS
If Drone drifts in any direction while hovering (and you are not pressing the
Direction stick), you may need to make trim adjustments. Safely land Drone
on a level surface. Press the recommended Trim button as described below.
1
2
3
(Remark - When the remote LED ashes 3 times quickly, the trim just goes
back to the middle of trim range). You still need to trim it as described if
you nd drone drift. Launch Drone back into the air and attempt another
still hover. If Drone continues to drift, repeat the process until a still hover
is achieved:
•
Drone drifts forward (Fig. 1)
– Press the B button
•
Drone drifts backward (Fig. 2)
– Press the F button
•
Drone drifts to the left (Fig. 3)
– Press the R button
HIGH
LOW
OFF
1 Turn OFF Remote Control.
2
1
OFF
2 Move the switch on the rear of the Drone to the
OFF position.
3 Now move the same switch on the Drone to the
ON position.
1
4 Quickly place the Drone on a
FLAT LEVEL SURFACE.
5 Turn Remote Control ON (Middle position).
6 Slowly push remote control THROTTLE STICK
UP until Drone lifts into the air.
IMPORTANT: YOU ONLY HAVE A FEW
SECONDS AFTER THE DRONE IS
SWITCHED ON TO PLACE THE DRONE ON
A LEVEL SURFACE FOR PROPER CALIBRATION. IF DRONE DOES NOT RISE TO A
STABLE HOVER OR FLIES ERRATICALLY,
REPEAT STEPS 1 THROUGH 6.
2
OFF ON
OFF ON
3
CAUTION: NEVER APPROACH DRONE
WHILE THE PROPELLER BLADES ARE
STILL SPINNING. THROTTLE DOWN UNTIL
THE BLADES STOP THEN TURN OFF
REMOTE BEFORE ATTEMPTING TO
HANDLE DRONE.
4
4
•
Drone drifts to the right (Fig. 4)
5
– Press the L button
•
Drone spins counter-clockwise, when viewed from the top (Fig. 5)
– Press the button
5
6
•
Drone spins clockwise, when viewed from the top (Fig. 6)
– Press the button
6
7 4
3A
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 7 / PAGE 4
FLIGHT CONTROLS
Familiarize yourself with Drone’s
controls before ying!
Press UP
to lift
THROTTLE/ROTATION STICK
• To make the Nano Drone LIFT, push the Throttle stick FORWARD.
• The further you PUSH the Throttle stick, the faster you LIFT.
• To make the Nano Drone HOVER, nd the sweet spot on the throttle stick
(somewhere in the middle).
Power indicator LED
Power On/Off Switch
Press UP
to fly forward
Press DOWN
to descend
Press LEFT
to rotate counter-clockwise
Press RIGHT
to rotate clockwise
STUNT Button
THROTTLE/
ROTATION STICK
Rotation Trim
DIRECTION STICK
•
•
Forward/Backward Trim
DIRECTION STICK
Flight Sensitivity Switch
Push the Direction stick FORWARD to y forward or away from you (Green blade in front).
Push BACKWARD to y backward.
The farther you push, the faster Drone ies in that direction.
Push the Direction stick LEFT to y left. Push RIGHT to y right.
The farther you push, the faster Drone ies sideways.
Left/Right Trim
Press DOWN
to fly backward
Press LEFT
to fly left
Press RIGHT
to fly right
5 6
3B
SIZE: 297 x 210mm (folds to 148.5 x 210mm)
PAGE 5 / PAGE 6
Loading...