SkyRC SR4 User guide

TABLE OF CONTENTS

INTRODUCTION

简介…………………………………………………………………………………………………………………………………………..………………………

SAFETY PRECAUTIONS

安全提示……………………………………………………………………………………………………………………………………………………………

RUNNING IN WET CONDITIONS

潮湿条件驱车……………………………………………………………………………………………………………………………..………………………

AFTER RUNNING IN WET CONDITIONS

潮湿条件驱车后注意事项……………………………………………………………………………………………………………..……………………...
FEATURE

产品特点………………………………………………………………………………………………………………………………….....……………………..

MOTOR GEARING

马达齿轮…………………………………………………………………………………………………………………………………………………………....

SPECIFICATION

参数…………………………………………………………………………………………………………………………………...……………………............

ILLUSTRATION OF MAIN PARTS

产品主要部件图示……………………………………………………………………………………………………………...……………………............

EXPLODED VIEWS

分解图………………………………………………………………………………………………………………………………………..……………………..

READY TO RUN PREPARATION

跑前准备工作……………………………………………………………………………………………………………………………...……………………..

HELPFUL HINTS FOR ASSEMBLY

安装提示…………………………………………………………………………………………………………………………………………………………....

TROUBLE SHOOTING

疑难解答…………………………………………………………………………………………………………………………………………………………....

WARRANTY

保修条款…………………………………………………………………………………………………………………………………………………………....

目 录

02

04

05

05

05

05

06

06

07

08

12

13

13

IMPORTANT NOTICE

SKYRC is unable to ensure that the user will follow
the instructions supplied with the bike, nor can
SKYRC control how the bike is assembled,
operated and maintained. For this reason, SKYRC
cannot be held responsibility for damage, loss, or
injury caused by the use of materials different from
what is indicated in the manual, or from the
improper use of the product. From the moment the
buyer begins the assembly progress, he is
assuming the responsibility of any consequence
resulting from misuse or assembly. If customer
can't accept this, please return the product to the
place of purchase. The returned item should be
new, unused and with complete package.

注意事项

本公司无法保证用户完全遵照说明书指示操作，
也不能确保客户后续能正确安装/改装、恰当操作及妥
善保养。因此，本公司不承担任何由于以下情况造成
的破损、损失及人身伤害的责任：

　　1. 用户使用与说明书描述不符的材料或者配件；

2. 用户操作或者使用不当。
　　从客户开始安装摩托车的那一刻起，客户将自行
承担由于使用不当造成的任何后果。如果客户不能接
受此条款，请将摩托车退回购买处。注意，退回的摩
托车必须全新，未使用，且包装完好。

01

INTRODUCTION

简介

Congratulations on your choice of the SkyRC
Super Rider SR4. This kit is a high performance
RC vehicle with electronic stabilizing system and
adjustable gyro effect control board. Please
carefully follow the instruction manual during
assembly and pay attention to the warnings.

SKYRC Super Rider SR4 is a fully ready-to-run 1/4
dirt motocross. All electronics and other
components are installed in the factory. The users
only need to install the battery, and then it is ready
to run. It is very stable even at very low speed.
What's more, it is also able to do quick brake and
jump in every different terrain and can do the off­road function in a superior way.

The point users concern most is the stability of the
motocross. This newly-developed Super Rider SR4
features a revolutionary stability technology ESS
(Electronic Stability System). This system consists
of a gyro effect governor and an electronic gyro in
rear wheel which makes the bike super stable
when running. The users can adjust the RPM of
the electronic gyro according to his request. There
are 4 kinds of RPM that can be selected by user,
8000RPM, 10000RPM, 11000RPM and
12000RPM. The beginners can choose 12000RPM
as the gyro effect is strong at this speed and the
motocross will be more stable. When the users are
familiar with the operation, he can choose lower
RPM and the sensitivity of the motocross will be
higher. Besides that, the oil shock absorbers in
both front and rear wheel also make the SR4 much
more stable than others.

Power is everything in motocross, and the SR4
comes with Toro 540 class 3200KV brushless
motor and Leopard 60A ESC V2. The motor and
ESC are all assemble well in the factory and the
users only need to connect a 2S or 3S Lipo battery
to the motocross, it will be ready to run. The
battery case is located at the bottom of the
motocross, it is simple and easy to take off the bolt,
open the case, put the battery into it and lock the
battery case. When the power system works, it will
burn out monster power. Even the motocross fall
down, the monster power can make it stand up by
itself. Users can run it wherever he feels like and
however fast he wants. Up hills and flying over
jumps or traveling on gravel and grass, dirt or

非常感谢您购买由天空创新科技（深圳）有限
公司研发生产的闪电骑士SR4。这是一款高性能的
电动遥控摩托车，配有电子平衡装置及可调节的陀
螺仪控制装置。安装时，请仔细阅读说明书及各项
警告。

闪电骑士SR4是一款1/4的遥控越野摩托车。所
有的电子零件及其他配件在工厂已经安装好。用户
只需装上遥控器及摩托车电池，就可以尽情操控摩
托车了。此款摩托车的稳定性能非常好，即使是低
速运行。在不同的场地，摩托车都能随时刹车跳
跃，在泥泞道路上能发挥出越野性能。

对于大多数用户来说，最关心的问题就是摩托
车的稳定性。这款最新研发的闪电骑士SR4运用了
开创性的ESS电子平衡系统。此系统由陀螺效应控
制板和后轮内的电子陀螺部件构成，可以提供超级
稳定的驾驶感觉。用户可以根据自己的需求，调节
电子陀螺仪的转速，有4种转速可供调节，
8000RPM,　10000RPM,　11000RPM和12000RPM。
初学者可以选择12000的电子陀螺转速，此时陀螺
效应非常强，稳定性好，摩托车可以超低速前进。
当用户熟悉操作后，可选择稍低的电子陀螺仪转
速，此时摩托车的操作灵敏性增强。除此之外，前
轮及后轮的油压减震系统也使闪电骑士SR4比市场
上其他的摩托车稳定。

对于任何一款遥控模型产品，最重要的莫过于
动力。闪电骑士SR4使用540级3200KV的无刷马达
以及豹子二代60A的无刷电子调速器。马达及电子
调速器在工厂已经安装完成并测试完成，用户只需
装上2节或者3节的锂聚合物电池，摩托车就可以奔
跑了。电池的安装非常简单，只需将电池盒上插销
取下，放入电池，再装上插销即可。通电之后，闪
电骑士将爆发出巨大的能量。即使摩托车在运行过
程中倒下了，仍能依靠自身强大的动力站立起来继
续奔跑。用户可以在任何地方以任何速度奔跑。爬
山，飞跃，跳跃，在草坪，灰尘地，甚至很多沙子
的地面，摩托车都能疾驰而过。直行/突转都在掌控
之中。

铝合金车架加上金属链条让闪电骑士SR4越野
摩托车非常的坚固耐用。配置的遥控器为2.4G，用

02

pavement. Users can scream down straight away
and corner with confidence.

The anodized aluminum chassis and metal chain
driver make the motocross strong and durable.

Generally speaking, SKYRC Super Rider SR4 is a
super stable motocross. With unique ESS
technology, creative design and delicate
workmanship, we believe you will have a totally
different feeling when riding.

户可以再崎岖的地方自行享受飞驰的乐趣，也能在
竞赛场地和其他玩家一决高下。

总之，闪电骑士SR4越野摩托车是一款超级稳
定的摩托车，因其独创的ESS电子平衡系统，极富
创意的设计以及精细的做工，我们相信将给用户提
供全新的驾驶体验。

ESS

ESS

Technology

电子平衡系统

Innovative Electronic Stability System (ESS) built
into the rear wheel incorporates a powerful
brushless motor and flying wheel which will provide
gyro effect for optimal stability. Individual
RPM(Rotations Per Minute) setting on the flying
wheel can be selected through Gyro Effect
Governor Board. High RPM provides optimal
stability but less cornering and low RPM provides
more maneuverability but less stability.

ELECTRONIC STABILIZING SYSTEM

ELECTRONIC STABILIZING SYSTEM

Flying Wheel

Brushless Motor

飞轮

天空创新科技(深圳)有限公司隆重推出1:4越野摩托车­闪电骑士SR4， 本车采用先进独创的电子平衡系统
（Electronic Stability System），此系统由陀螺效
应控制板和后轮内的电子陀螺部件组成。此系统提供
超级稳定的驾驶感觉，并可根据使用者的需求进行调
节，初学者可以使用较强的陀螺效应，使车身更加稳
定，熟练驾驶后可以降低陀螺效应，提高转弯操控的
灵活性。

电子平衡系统

The four variable RPM are

无刷马达

8000RPM,
10000RPM,
11000RPM,
12000RPM(factory default).
We recommend beginners to run
with high RPM

Speed Control

RPM LED Indicator

四档转速指示灯

Gyro Effect Governor Board

陀螺效应控制板

电调

四级可选电子陀螺仪转速为
8000RPM，
10000RPM，
11000RPM，
12000RPM（工厂默认设置）。
建议初学者选择高转速

Switch for
RPM Setting

飞轮转速
调节开关

Rear Tire

后轮胎

03

SAFETY PRECAUTIONS

1.

Keep away from moving parts to avoid injury of
your fingers and hands.
Do not operate this model close to people. Make

2.

sure the spectators are at a safe distance behind
the operator.

3.

Do not use this model in the place where is not
suitable to play, such as public roads, crowded
places, near an airport or wherever the use of
radio-controlled models is forbidden.

4.

Make sure to read the battery and charger
instruction before charging and using the battery.

5.

When charging battery, please make sure there
is someone aside. If the battery or charger
becomes hot, disconnect the battery from
charger immediately! Fail to do so may cause
damage to battery, charger, property loss, even
body harm.
Do not cover the air intake holes on the charger

6.

which may cause overheat of the charger.
Don't allow moisture, debris, water or other

7.

material get into the ESC and other electronics
which may cause short circuit or other damages.
Turn the transmitter ON before start and OFF

8.

after finish.
Turn on the ESC after the transmitter is ON and

9.

turn off it before the transmitter is OFF.

10.

Make sure the motor and ESC has cooled down
before next run.
Do not operate with the low voltage batteries. It

11.

may cause the bike out of control or damage of
the battery.

12.

Disconnect battery with the vehicle if you do not
use it.

13.

This product is not a toy.

14.

Keep this product and all the relevant
components away from children younger than 3
years old as the small components can be a
chocking / swallowing hazard!

15.

This is a high performance product and it can be
used by persons older than 14 years old only.

16.

First-time builders should seek advice from
people having building experience in order to
assemble the model correctly and to produce its
performance to full extent.
Tak e enough safety precautions prior to

17.
operation this

18.

You are responsible for this model's assembly
and safe operation!

19.

Taking out liability insurance is recommended.

model.

安全提示

1.

请远离正在运行的机件以免擦伤您的手指。
请不要在人员密集的地方操作模型，请确保旁观者

2.
在操作者身后并保持一定的安全距离。
请远离公共场所，如马路，人员密集区，机场附近

3.
或者禁止使用无线电操控的区域，否则会伤及他人
或者造成其他无线电设备的信号丢失等现象。
请确保用充电器给电池充电之前，仔细阅读充电器

4.
和电池的说明书，并且谨记锂电池的相关警告语。
对电池进行充电时，请确保旁边有人。当发现充电

5.
器或者电池变烫时，请及时断开电池及充电器。否
则会损害充电器以及破坏电池特性以及缩短电池寿
命，甚至会造成人身伤害以及财产损失。
充电过程中请勿堵住或盖住充电器的通风（散热）

6.
口，否则会造成充电器过热保护，因而需重新启动
充电器。
不要让杂质，尘埃，水等其他物质进入电调等电子

7.
设备，这可能引起短路或者其他伤害。

8.

请在开始前打开遥控器开关，结束后最后关闭遥控
器开关。
电调在遥控器打开后才开，遥控器关闭前关闭。

9.
请在下一轮的使用前确保马达和电调已经冷却。

10.

11.

请不要在电池电压过低的情况下操控模型，这样可
能造成摩托车失控或损坏电池。
在不用的情况下请将电池从模型车中取出。

12.
此产品不是玩具。

13.
保证产品及相关的配件远离三岁以下的儿童，避免

14.
小零件被儿童吞咽，误食。
这款产品性能非常卓越，适用于14岁以上的玩家。

15.
第一次安装时，请向有摩托车安装经验的玩家寻求意

16.
见，从而保证安装正确，使产品性能得到完全发挥。
操控摩托车时，安全第一，请仔细阅读相关安全提示。

17.
用户对安装及操作过程负责。

18.
推荐购买责任保险。

19.

04

RUNNING IN WET CONDITIONS

1.

Although your model is waterproof, extra care is
necessary when running in wet conditions; or it
may cause serious damage to your model.
The transmitter, receiver and ESC are NOT

2.

waterproof.
Do not operate your model when it is lightning.

3.

Keep far away from salt water or contaminated

4.

water when operating the model.

AFTER RUNNING IN WET CONDITIONS

潮湿条件驱车后注意事项

1.

Unplug the battery from the model.

2.

Use air-compressor to dry your model.
Spray bearings, fasteners, and drive train or

3.

similar product.
Check bearings, drive train and other components

4.

for well operation before next use.

潮湿条件驱车

即使模型防水，在潮湿雨水条件中驱动车子仍须特

1.
别留意，稍不留意都有可能会严重损害模型车。
遥控器、接收机、电子调速器及其它电子设备不防水。

2.
闪电的时候请不要操控您的模型车。

3.
在操控模型的时候请远离盐水、海水或污水区域。

4.

断开电池与摩托车。

1.
用空气压缩机烘干模型。

2.
吹干轴承链条或者类似的部件。

3.
检查轴承，链条和其他部件，以便下次能顺利操

4.
作。

FEATURES

1/4 Scale, strong and durable anodized aluminum
chassis and metal chain driver.
Revolutionary stability technology ESS
(Electronic Stability System).
Gyro effect governor.
Monster power system, easy & quick
installation and maintenance.
Selectable RPM suitable for both beginners and
experienced player.
Front/wheel oil shock absorber.

MOTOR GEARING

GEAR

SPUR

67

P

10

I

11

N

I

12

O

13

N

6.70:1

6.09:1

5.58:1

5.15:1

68

6.80:1

6.18:1

5.66:1

5.23:1

产品特点

1/4车型，坚固耐用的氧化铝质车架以及金属链
条。
独创的ESS电子平衡系统。
陀螺效应控制板。
爆发力强，安装及保养简单快捷。
可供选择的电子陀螺仪转速，适合初学者及高级玩
家。
前轮及后轮都有油压减震器。

马达齿轮

05

SPECIFICATION

参数

Motor: 540 Brushless 3200kv
ESC: 60A 2.4G Radio
Support 2-3S LiPo
Front/Rear Oil Shock Absorber
Wheel Front: 160mm
Wheel Rear: 150mm
High-Torque Servo
Length: 525mm Height: 416mm
Net Weight: 2760g

马达：540级无刷3200KV
电调：60安 　2.4G遥控器
支持2-3节锂电
前/后油压避震器
前轮直径：160毫米
后轮直径：150毫米
高扭力舵机
长度：525毫米　　高度：416毫米
净重：2760克

ILLUSTRATION OF MAIN PARTS

骑士

Rider

Rear Tire

后轮胎

产品主要部件图示

Support Bar

支撑杆

Aluminum Chassis

铝合金车架

Power Switch

电调开关

Front Shock

Mudguard

前避震器挡泥板

ESC

电调

Receiver

接收机

Gyro Effect Governor

陀螺效应控制板

Oil-filled Rear Shock

后油压减震装置

Metal Chain Drive

金属链条

Front Wheel Mudguard

前轮挡泥板

Oil-filled Front Shock

前油压减震装置

Front Tire

前轮胎

Brushless Motor

无刷马达

Battery Case

电池盒

06

EXPLODED VIEWS

分解图

07

READY TO RUN PREPARATION

跑前准备工作

This is RTR(Ready to run) version. It is ready to run after
user installs the battery, connects ESC and switches on
the transmitter and ESC. We suggest the user follow
below steps to operate and check the bike for the first
use. For future use, user could adjust some settings
according to his request.

Step 1 Check all the parts in the box.

When you open the box, you will find a set of RC
bike with rider, a piece of transmitter and a wire for
pairing transmitter and receiver.

锂电充电器

Note: Make sure the battery is fully charged before
installing. Weak power may cause the bike out of control
and make damage to the bike, property loss or body
damage.

2节或3节锂电池

本产品为RTR版本，用户安装好电池（遥控器，摩
托车），连接电调，打开遥控器及电调开关，便可使
用。第一次使用，建议用户按以下步骤操作并检查整
个产品。以后每一次使用之前，用户可根据需要，对
相关设置做调整。

步骤1　检查包装里的部件

打开包装盒，你会发现里有遥控器、对码线和摩
托车（骑士已经安装完成）。

以下配件客户需单独购买

8节5号电池用于遥控器

注意：请确保电池充满电。摩托车电量不足可能引起摩托车
性能无法正常发挥。遥控器电池电量不足会引起摩托车车速
缓慢，失控，引起财产损失，甚至人身伤害。

Step 2 Install batteries to the transmitter and

check whether it works properly.

Step 3 Check the wires are all connected well.

All the wires are connected well in the factory and we
suggest you re-check whether they get loose while
delivery before use.

1. The wire between ESC and receiver.

2. The wire between servo and receiver.

3. The wire between ESC and motor.

Step 4 Install battery to the bike and connect 　

the battery to the ESC

How to install the battery

Remove the R-clip, open the cover of battery case.

1.

2.

Install the battery into the battery case.
Close the door, secure in place with the R-clip.

3.

4.

Connect

NOTE 1

NOTE 2

the battery with the ESC.

With the ESC "off, plug the battery into the ESC 　
lead.
Please keep the battery wire and the ESC wire in
the same side before locking the battery door.

步骤2　装遥控器电池并检查遥控系统是否正常工作。

步骤3　检查所有接线是否完好。

以下接线在出厂时已经全部接好，建议用户使用前再
次检查接线在运输途中是否松动。

1. 电子调速器及接收机连接线。

2. 舵机及接收机连接线。

3. 马达及电子调速器连接线。

步骤4 安装摩托车电池并连接电池和电子调速器。

如何安装电池？

取出锁扣，打开电池盒盖。

1.
将电池安装至电池盒位置。

2.
合上盒盖，插上锁扣固定。

3.
连接电池和电调。

4.

提示1：电池连接电调前，保持电调处于关闭状态。
提示2：固定盒盖前，确认电池硅胶线和电调连接

　　　　线在同一侧。

08

08

Battery Case

Connect

ESC Switch

142x47x22mm

Connect

321

4

Step 5 Set the radio system

How to set the radio system?

Caution: Calibration is necessary for the first use of the
ESC, or whenever used with a new/different transmitter.
Different transmitter's signals for full throttle, full brake
and neutral varies. You must calibrate your ESC so that
it will operate more effectively with you transmitter.

Please make sure the ESC is off before setting.

1

2

3

4

1 Open the top cover of the transmitter.and witch on the

s

transmitter.

Hold full throttle on the transmitter and turn on the

2.

ESC switch. Keep holding the full throttle and the
motor will ring the initialization tones (All the sounds
are played by ESC vibrating the motor).

The ESC will detect the battery cells, if the battery

3.

pack is 2 cells, it will beep 2 times (Beep-Beep-); if it
is 3 cells, it will beep 3 times (Beep-Beep-Beep- )…

3 seconds later, the motor will play one multi-toned

4.

ring which indicates the calibration of full throttle is
finished.

5.

Move the throttle trigger to full brake, the motor will
ring like Beep-Beep-Beep (It means the ESC is
looking for full brake endpoint), 3 seconds later, the
motor will play one multi-toned ring which indicates
the calibration of full brake is finished.

Relax trigger to neutral (center), the motor will ring

6.

like Beep-Beep-Beep (It means the ESC is looking
for neutral position), 3 seconds later, the motor will
play one multi-toned ring which indicates the
calibration of neutral position is finished.

2 seconds later, the motor will play one multi-toned

7.

ring. That means the ESC calibration is finished and
it is ready to work with transmitter now.

5

6

7

8

9

步骤5　控制系统设置

如何设置遥控器？

警告：第一次使用电子调速器或者使用新的/不同的遥控器，
都必须对电子调速器进行重新校准。不同遥控器油门的正反
方向，刹车，油门中立点的信号也不同。为了使电子调速器

能有效的工作，建议你在使用前，重新校准。
设定开始之前，请保证电调处于关闭状态。

ST NOR/REV

1

方向 正/反

POWER LED

2

电源指示灯

ST TRIM

3

方向微调

POWER SW

4

电源开关

TH NOR/REV

5

油门 正/反

POWER CHECK

6

电压指示

BIND

7

对码按钮

TH TRIM

8

舵量

D/R

9

油门微调

1. 打开遥控器顶端半透明盒盖， 再打开遥控器开关。

油门加到最大，持续按住遥控器油门不松开，打开

2.
电调开关，马达发出初始音(校准过程所有声音由马
达发出)。

电调开始检测电池组节数，如果2节，发出2声“哔

3.
哔”，如果3节，则发出3声“哔哔哔”，以此类推。

3秒钟后，马达发出一串音乐，最大油门校准完毕。

4.

移动油门至最大刹车区域（反向最大区域），马达

5.
持续发出“哔哔哔”（最大刹车点检测中）， 3秒后，
马达发出长串音乐，最大刹车点校准完毕。

松开油门使其回到中立点位置，马达持续发出“哔哔

6.
哔”（油门中立点检测中），3秒后，马达发出长串
音乐，油门中立点校准完毕。

2秒后，马达再次发出长串音乐，表示电调校准完

7.
成，可以接受遥控器指令。

ESC Switch

Full Throttle Full Brake

Neutral (Centre)

09

09

※ COUNTER-STEERING SYSTEM ※ 反向操作系统

The SR4 comes with a Counter-Steering System. It
means the direction between the transmitter
steering wheel and the bike's front wheel are
opposite. When the transmitter steering wheel
turns left, the front wheel of the bike turns right;
when the transmitter steering wheel turns right, the
front wheel of the bike turns left.

LEFT

NEUTRAL RIGHT

SR4电动摩托车的操作系统是反向的，遥控器的操
控轮与摩托车车前轮的方向相反。遥控器方向轮控制
与摩托车前轮转向方向相反。左转遥控器方向转轮，
摩托车前轮右摆；右转遥控器方向转轮，摩托车前轮
左摆。

Until now, all the preparation job is finished. The
last step is final adjustment.
Hold the bike in the air and run the rear wheel,
make sure it runs forward.

※ ELECTRONIC STABILIZING SYSTEM
　 ADJUSTMENT

The main feature of this bike is its innovative
Electronic Stability System(ESS)
the rear wheel incorporates a powerful brushless
motor and flying wheel which will provide gyro
effect for optimal stability. Individual RPM
(Rotations Per Minute) setting on the flying wheel
can be selected through Gyro Effect Governor
Board. High RPM provides optimal stability but less
cornering and low RPM provides more
maneuverability but less stability.
The four kinds of RPM are 8000RPM, 10000RPM,
11000RPM, 12000RPM(factory default).
We recommend beginners to run with high RPM.

which built into

到这一步，所有的准备工作已经完成，最后一步就是
最终调试。
举起摩托车打开开关使后轮在空中空转，确定其转向
向前。

平衡系统·陀螺效应调节

※

闪电骑士SR4遥控越野摩托车最主要的特点就是采用先
进独创的电子平衡系统（Electronic Stability
System)来保证摩托车在运行过程中的平衡。此系统

由陀螺效应控制板和后轮内的电子陀螺部件组成。此
系统提供超级稳定的驾驶感觉，并可根据使用者的需
求进行调节，初学者可以使用较强的陀螺效应，使车
身更加稳定，熟练驾驶后可以降低陀螺效应，提高转
弯操控的灵活性。
四种可选电子陀螺仪转速为8000RPM，10000RPM，
11000RPM，12000RPM（工厂默认设置）。
建议初学者选择高转速。

10

10

Electronic Gyro RPM adjustment

Remove the rider and the plastic cover.

1.
Release the screws of both side which

1)
locate at the riders’ feets .

2)

Lift the rider and move it to the front of
motorcycle.

3)

Remove the R-clip, take off the gyro
governor cover from motorcycle.

Electronic Gyro RPM adjustment.

2.
Release the screws and remove the

1)
transparent cover of control box.

2)

Press the white Button , choose RPM ( LED
flashes with different numbers of beeping
sound which indicates users’ RPM selection).

LED Color RPM

Orange
White
Green
Red

8000
10000
11000
12000

No. of Beep

1
2
3
4

3) Secure the gyro governor cover with screws.

设置电子陀螺仪转速

1. 拆除骑士模型，及摩托车车壳。

　 1) 松开骑士脚底部两边螺丝。

　 2) 向上扳起骑士模型至摩托车头部位置。

　 3) 拔掉R扣，拆下摩托车车壳。

2. 调节陀螺仪转速值。

1) 松开电子陀螺仪控制盖的螺丝，打开控制盒的透
　　 明盖。

2) 通过陀螺仪控制器的按钮调节陀螺仪转速。（选
　　 择转速值，对应LED灯闪烁，并伴随不同数量的
　　 哔哔声，指示所选转速）

指示灯颜色

橙色
白色
绿色
红色

　3) 用螺丝将陀螺仪盖装回去固定。

转速

8000
10000
11000
12000

声音次数

1
2
3
4

1 2 3

Transparent cover

控制盒透明盖

RPM LED Indicator

转速选择指示灯

Switch for RPM

7

Setting

转速调节按钮

456

11

11

PRE-RUN CHECKLIST

跑前检查

Note: The built-in electronic gyro will start running
once you connect the battery to the ESC and it will
come into full effect after 1 minute running.

Make sure there is no rocks and small debris in

1.
chain and sprocket. Make sure the chain and
sprocket moves freely.
Make sure the transmitter is ON.

2.
Make sure the throttle is in neutral position.

3.
Turn off the transmitter AFTER cutting off the

4.
power.
Make sure the running area is large and free

5.
from obstacles and small children. For the
beginners we recommend a large open parking
lot. Any RC bike will have unique handle
characteristics that you need to understand
before pushing the bike to the extreme.

CAUTION

Before you power on the bike, please make
sure the bike stand is not on metal or con­ductive surface, it may cause short circuit
and the ESC and gyro may get burnt.

注意： 一旦连上电池及电调，内置陀螺仪即开始运
转，电子陀螺效应开始启动，请等候一分钟，使陀螺
效应达到最大效果。

请检查链条及链轮上没有小石头及其他碎片，保证

1.
链条及链轮能运行自如。
遥控器保持开启状态。

2.
确保油门，方向在中位位置。

3.
关闭系统时，先切断动力电源，再关闭遥控器。

4.
请远离儿童并在空阔区域操作，对于初学者我们建

5.
议去空旷的开放型停车区。任何遥控器的手柄都有
独特的特征， 在全力驱车前请了解清楚并熟悉操
作。

警告

摩托车通电之前，请确定摩托车后轮固定
支架没有放在金属或者易导电材质的桌面
上，以免短路造成陀螺仪启动电调烧坏。

Until this step the bike is ready to run.

HELPFUL HINTS FOR ASSEMBLY

Avoid working on a deep pile carpet. It is

1.
difficult to find some small components, such as
screw, if you drop them into it.
To prevent parts from rolling off and protect the

2.
working surface, you could put all the small
parts into a container.
Avoid running the bike in cold weather. Low

3.
temperature may cause plastic and metal parts
brittle. What’s more, the grease and oil become
thick which may cause poor performance.
Test fit all parts before attaching them to the

4.
bike.

到这里，所有的安装调试、检查过程全部完成

安装提示

尽量不要在长毛地毯上操作摩托车，如果零配件，

1.
例如螺丝，掉进地毯，很难找到。
为了不让零件滚落，最好将所有部件放在容器里。

2.
尽量避免在天冷的时候操作摩托车。低温会引起塑

3.
料机金属部件会变脆，容易折断。而油也会变浑
浊，影响摩托车性能。
在固定各部件之前，请确保各部件之间完全吻合。

4.

12

12

TROUBLE SHOOTING

疑难解答

Problem 1 The motorbike does not move.
Cause

1) Battery in motorbike or transmitter is no power.

2) Motor may be broken.

3) ESC does not work.

4) The setting of transmitter or ESC may be

wrong.

Problem 2 The model is out of control.
Cause

1) Transmitter or antenna may be broken.

2) The motorbike may be out of range from

transmitter.

3) Power of the transmitter is weak or dead.

Problem 3 Short run time.
Cause

1) Battery may be damaged.

2) Charger may be damaged.

3) Battery is not with full power.

Problem 4 Poor performance of the motorbike.
Cause

1) Suspension may not run freely.

2) The steering may be damaged.

3) Chain may be too loose or too tight.

4) Rear wheel may not adjust straight.

问题：摩托车没有动力。

1.
原因分析：
1）摩托车电池或者遥控器电池损坏。
2）马达损坏。
3）电调不工作。
4）遥控或电调设置错误。

问题：摩托车不受控制。

2.
原因分析：

1) 遥控器或天线损坏。

2) 摩托车跑出遥控器控制范围。

3) 遥控器没电或电池电量不足。

问题：摩托车跑动时间短。

3.
原因分析：
1）电池可能损坏。

2）充电器可能损坏。
3）电池未充饱。

问题：摩托车性能低。

4.
原因分析：
1）避震器缓冲功能存在问题。
2）舵机损坏。
3）摩托车链条过松，或过紧。
4）后轮方向未调整正确。

WARRANTY

Each kit is inspected and adjusted carefully before
leaving our factory and we guarantee the kit be
free of material defects and workmanship faults.
We will repair the kit for customer free of charge
within 90 days after the purchase date.
The warranty doesn’t cover crash damage,
modification, failure to maintenance, or the
damaged caused by improper use.
The warranty doesn’t cover any result which
caused by final user’s assembly or the material
used for final user’s assembly.

保修条款

每辆摩托车出厂之前都经过严格的测试及调试，
我公司保证，客户购买的产品打开包装后，无任何材
料及工艺方面的问题。购买之日90天内，我公司将免
费为客户维修。
　　由于碰撞，翻车，用户自行更改配置，疏于保养

或者任何不当使用引起的损坏，将不在保修范围内。
　　由终端用户自行安装或自行安装所使用的材料所
引起的任何问题，亦不属于保修范围。

Please download the Assembly Manual & Part List from our website:

请登录SKYRC网站下载详细安装说明及配件图：

http://www.skyrc.com

13

13