Skyrc D1000 V2 User Manual

Download

AC/DC Dual Balance Charger Discharger / Power Supply

Instruction Manual

[Version 1.20]

Table of Contents

Introduction

Special Features

Warning and Safety Notes

Explanation of Buttons

Operating Program

Lithium Battery Program (LiPo/LiFe/LiIon/LiHV)

NiMH/NiCd Battery Program

Pb Lead-acid Battery Program

DC Power Supply

Battery Memory Set and Call Out

System Setting

Battery Voltage Meter

Battery Resistance Meter

Controlling the Charger Using the App

Using the Charge Control Software “Charge Master”

Specification

Regulatory Information

Warranty and Service

WARNING:

This charger is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the charger. Do not recharge non-rechargeable batteries!

During charging, the battery must be placed in a well-ventilated area! Never leave the charger unattended when charging the battery.

Introduction

Congratulations on your choice of SKYRC D100v2 AC/DC Dual Balance Charger/Discharger/Power Supply. This unit is simple to use, but the operation of a sophisticated automatic charger such as SKYRC D100v2 does require some knowledge on the part of the user. These operating instructions are designed to ensure that you quickly become familiar with its functions. It is therefore important that you read right through the Operating Instructions, Warning and Safety Notes before you attempt to use your new charger for the first time. We hope you have many years of pleasure and success with your new battery charger.

SKYRC D100v2 is a twin-channel charger with two independent circuits which can charge batteries of varying chemistries (LiPo/LiFe/Lilon/LiHV/NiMH/NiCd/ Pb) simultaneously. Capable of operating as a power supply with the maximum output of 100W helps the hobbyists to power other DC equipments. With its unprecedented function of voice guide, even a freshman can operate this charger easily. Additional feature including our "SCAN TO GO" and smart phone control via Bluetooth.

Please BE SURE to read these INSTRUCTIONS, WARNING and SAFETY NOTES before you use the charger for the first time.

It can be dangerous to mis-handle batteries and battery chargers, as there is always a risk of batteries catching fire and exploding.

Mishandling batteries and battery chargers is extremely dangerous, which may cause fire and explosion.

D100v2

01 ·

Introduction

Please read this entire operating manual completely and attentively before using this product, as it covers a wide range of information on operating and safety. Or please do use this product in company with a specialist!

Dot Matrix 128x64 LCD Display

Output Socket

4mm Banana Plug

Balance Lead Socket

Temperature

Sensor Port

USB Port

Micro USB Port for

PC Link &

firmware upgrade

Temperature

Sensor Port

Resume or Start Charge Processes

Balance Lead Socket

Output Socket

4mm Banana Plug

Alter Values See the Status of Individual Cells in Balance Charge Mode

Cooling Fan

Scroll Through the Main Menu Stop Any Charge Processes

Switch from Channel A to B or Channel B to A

DC Power LED Light

DC Input: 11-18V DC Output: 13.8V

· 02

Speaker

AC Input 100-240V

D100v2

Special Features

LiPo

NiMH

Twin-channel Charger

SKYRC D100v2 allows you to plug 2 batteries into one charger simultaneously, and it will intelligently and automatically charge 2 battries at once to their maximum capacity. To top of it, the batteries being charged do not even need to have the same configuration. You can connect different chemistry(LiPo/LiFe/Lilon/LiHV/NiMH/NiCd/Pb)batteries into any of the charging ports.

Dual Input and Power Distribution

The input of the charger is AC 100-240V and DC 11-18V. In DC mode, the power of each channel is 100W. Total power is 200W. In AC mode, it supports power distribution, between Channel A, Channel B & Power Supply. For example, if both channel A and channel B are set to 40W, then, the DC power is 20W. The total power is 100W. (40W+40W+20W=100W)

Optimized Operating Software

SKYRC D100v2 features the so-called AUTO function that sets the feeding current during the process of charging or discharging. Especially for lithium batteries, it can prevent the overcharging which may lead to an explosion due to the user's fault. It can disconnect the circuit automatically and alarm once detecting any malfunction. All the programs of this product were controlled through two way linkage and communication, to achieve the maximum safety and minimize the trouble. All the settings can be configured by users!

DC Power Output Supported

With the unique feature of DC power source, the user does not have to carry additional big and heavy power supply to the racing track or flying filed.

Voice Guide

Purposes to make the charger more intuitive and user friendly.

D100v2

03 ·

Special Features

Battery Memory (Data Store/Load)

The charger can store up to 10 different charge/discharge profiles for each channel. You can keep the data pertaining to program setting of the battery of continuous charging or discharging. Users can call out these data at any time without any special program setting.

Terminal Voltage Control(TVC)

The charger allows user to change the end voltage. (for expert user only)

PC Control Software “Charge Master”

Smart Phone Control via Bluetooth (both iOS and Android)

The charger can be operated with a smart phone via bluetooth connection.

SCAN TO GO

A very unique feature of D100v2 is SCAN TO GO (automatically charging system). As the range of battery types and capacity becomes more and more, each battery requires its own dedicated charging process. It is easy to set up the charger incorrectly for a specific type of battery, resulting damage the battery or even cause accident.

The revolutionary SCAN TO GO provides a solution to this problem by allowing the user to assign a QR Code which contains all the relevant data for the battery for charging or discharging. The user can create a unique QR Code by using “SkyCharger” apps. Print it and paste it on the battery.

Using your smart phone and launch “SkyCharger” app. Since all the essential information is stored in the QR Code. All you need to do is press the Scan button, and the charge or discharge process will start automatically.

Balancing Individual Cells Battery During Discharging

During the process of discharging, SKYRC D100v2 can monitor and balance each cell of the battery individually. Error message will be indicated and the process will be ended automatically if the voltage of any single one cell is abnormal.

Fast Charge and Storage Mode of Lithium Battery

Function of the two modes differs from each other. “FAST CHG” minimizes battery charge time, while “STORAGE” has the capacity to control the final battery voltage, which is necessary and helpful for a rarely used battery.

Re-Peak Mode of NiMH/NiCd Battery

In re-peak charge mode, the charger can peak charge the battery once, twice or three times in a row automatically. This is good for making the battery fully charged.

· 04

D100v2

Special Features

Delta-peak Sensitivity for NiMH/NiCd

Delta-peak sensitivity for NiMH/NiCd battery: The automatic charge termination program based on the principle of the Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process will be terminated automatically.

Cyclic Charging/Discharging

1 to 5 cyclic and continuous process of charge > discharge or discharge > charge is operable for battery refreshing and balancing to stimulate the battery's activity.

Automatic Charging Current Limit

You can set up the upper limit of the charging current when charging your NiMH or NiCd battery, it is useful for the NiMH battery of low impedance and capacity in the 'AUTO' charging mode.

Battery Voltage Meter

The user can check battery's total voltage, the highest voltage, the lowest voltage and each cell's voltage.

Battery Internal Resistance Meter

The user can check battery's total internal resistance and each cell's internal resistance.

Capacity Limit

The charging capacity is always calculated as the charging current multiplied by time. If the charging capacity exceeds the limit, the process will be terminated automatically when you set the maximum value.

Temperature Threshold*

The battery's internal chemical reaction will cause the temperature of the battery to rise. If the temperature limit is reached, the process will be terminated.

This function is only available by connecting optional temperature probe, which is not included in the package.

Processing Time Limit:

You can also limit the maximum process time to avoid any possible defect.

USB Power 5V/2.1A

You can charge your phone and tablet using the built-in USB power output port.

D100v2

05 ·

Warning And Safety Notes

These warnings and safety notes are particularly important. Please follow the instructions for maximum safety; otherwise the charger and the battery can be damaged or at worst it can cause a fire.

Never leave the charger unattended when it is connected to its power supply. If any malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operation manual.

Keep the charger well away from dust, damp, rain, heat, direct sunshine and vibration. Never drop it.

The allowable DC input voltage is 11~18V DC.

The allowable AC input voltage is 100~240V AC.

This charger and the battery should be put on a heat-resistant, non-inflammable and non-conductive surface. Never place them on a car seat, carpet or similar. Keep all the inflammable volatile materials away from operating area.

Make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger. If the program is set up incorrectly, the battery and charger may be damaged .It can cause fire or explosion due to overcharging.

Standard Battery Parameters

LiIon

3.6V/cell

4.1V/cell

3.7V/cell

≦1C

Nominal Voltage

Max Charge Voltage

Storage Voltage

Allowable Fast Charge

Min. Discharge Voltage

LiPo

3.7V/cell

4.2V/cell

3.8V/cell

≦1C

3.0-3.3V/cell 2.9-3.2V/cell

Be very careful to choose the correct voltage for different types of battery otherwise you may cause damage to the batteries. Incorrect settings could cause the cells to fire or explode.

LiFe

3.3V/cell

3.6V/cell

3.3V/cell

≦4C

2.6-2.9V/cell

LiHV

3.8V/cell

4.35V/cell

3.85V/cell

≦1C

3.1-3.4V/cell

NiCd

1.2V/cell

1.5V/cell

n/a

NiMH

1.2V/cell

1.5V/cell

n/a

1C-2C

0.1-1.1V/cell 0.1-1.1V/cell

1C-2C

2.0V/cell

2.46V/cell

n/a

≦0.4C

1.8V/cell

· 06

D100v2

Warning And Safety Notes

Never attempt to charge or discharge the following types of batteries.

A battery pack which consists of different types of cells (including different manufacturers) A battery that is already fully charged or just slightly discharged. Non-rechargeable batteries (Explosion hazard). Batteries that require a different charge technique from NiCd, NiMH, LiPo or Gel cell (Pb, Lead acid). A faulty or damaged battery. A battery fitted with an integral charge circuit or a protection circuit. Batteries installed in a device or which are electrically linked to other components. Batteries that are not expressly stated by the manufacturer to be suitable for the currents the charger delivers during the charge process.

Please bear in mind the following points before commencing charging:

Did you select the appropriate program suitable for the type of battery you are charging? Did you set up adequate current for charging or discharging? Have you checked the battery voltage? Lithium battery packs can be wired in parallel and in series, i.e. a 2 cell pack can be 3.7V (in parallel) or 7.4V (in series). Have you checked that all connections are firm and secure? Make sure there are no intermittent contacts at any point in the circuit.

Charging

During charge process, a specific quantity of electrical energy is fed into the battery. The charge quantity is calculated by multiplying charge current by charge time. The maximum permissible charge current varies depending on the battery type or its performance, and can be found in the information by the battery manufacturer. Only batteries that are expressly stated to be capable of quick-charge are allowed to be charged at rates higher than the standard charge current.

Connect the battery to the terminal of the charger: red is positive and black is negative. Due to the difference between resistance of cable and connector, the charger can not detect resistance of the battery pack, the essential requirement for the charger to work properly is that the charge lead should be of adequate conductor cross-section, and high quality connectors which are normally goldplated should be fitted to both ends.

Always refer to the manual by battery manufacturer about charging methods, recommended charging current and charging time. Especially, the lithium battery should be charged according the charging instruction provided by the manufacturer strictly.

D100v2

07 ·

Warning And Safety Notes

Attention should be paid to the connection of lithium battery especially.

Do not attempt to disassemble the battery pack arbitrarily.

Please get highlighted that lithium battery packs can be wired in parallel and in series. In the parallel connection, the battery’s capacity is calculated by multiplying single battery capacity by the number of cells with total voltage stay the same. The voltages imbalance may cause fire or explosion .Lithium battery is recommended to charge in series.

Discharging

The main purpose of discharging is to clean residual capacity of the battery, or to reduce the battery voltage to a defined level. The same attention should be paid to the discharging process as charging. The final discharge voltage should be set up correctly to avoid deep-discharging. Lithium battery can not be discharged to lower than the minimum voltage, or it will cause a rapid loss of capacity or a total failure. Generally, lithium battery doesn't need to be discharged. Please pay attention to the minimum voltage of lithium battery to protect the battery.

Some rechargeable batteries have a memory effect. If they are partly used and recharged before the whole charge is accomplished, they remember this and will only use that part of their capacity next time. This is a memory effect. It is said that NiCd and NiMH batteries are suffering from memory effect. NiCd has more memory effect than NiMH.

· 08

D100v2

Program Flow Chart

Note: The flow chart is taking one channel for example as the flow chart for the two channels (Channel A and Channel B) are identical.

DECINC

NiMH BATT

DECINC

NiCd BATT

DECINC

Pb BATT

DECINC

BATT METER

DECINC

Stop

Batt Type

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

START

ENTER

BATT/PROGRAM LiPo BATT

BATT/PROGRAM LiFe BATT

BATT/PROGRAM LiIo BATT

BATT/PROGRAM LiHV BATT

BATT/PROGRAM

BATT/PROGRAM BATT RESISTANCE

BATT/PROGRAM SYSTEM SETTING->

BATT/PROGRAM BATT MEMORY

LiPo BALANCE

2.0A 7.4V (2S)

LiFe BALANCE

2.0A 6.6V (2S)

Lilo BALANCE

2.0A 7.2V (2S)

LiHV BALANCE

2.0A 7.6V (2S)

NiMH CHARGE CURRENT 2.0A

NiCd CHARGE CURRENT 2.0A

Pb CHARGE

2.0A 2.0V (1P)

4.20 4.19 4.19 V

0.00 0.00 0.00 V

005 003 003 mΩ 005 mΩ

DC SUPPLY: OFF CH1: 50 CH2:50W

Version HW:1.00 FW: 2.00

[ BATT MEMORY 1 ] ENTER SET->

STARG/ENTER>3Seconds

ENTER CHARGER LOAD……

[ BATT MEMORY 2 ] ENTER SET->

[ BATT MEMORY 2 ] C:1.0A D:1.0A

START

ENTER CHARGER LOAD……

[ BATT MEMORY 3 ] ENTER SET->

Pb CHARGE

3.3A 4.0V(2P)

Pb DISCHARGE

1.5A 4.0V(2P)

ENTER > 3s

INC

LiPo CHARGE

2.0A 7.4V (2S)

DEC

INC

LiFe CHARGE

2.0A 6.6V (2S)

DEC

INC

Lilo CHARGE

2.0A 7.2V (2S)

DEC

INC

LiHV CHARGE

2.0A 7.6V (2S)

DEC

INC

NiMH Auto CHARGE CURRENT 2.0A

DEC

INC

NiCd Auto CHARGE CURRENT 2.0A

DEC

INC

Pb DISCHARGE

0.1A 2.0V (1P)

DEC

INC

MAIN 0.00V H0.000V L0.000V

DEC

INC

TATAL: 16mΩ H: 5mΩ L: 3mΩ

DEC

INC

Safety Timer ON 120Min

DEC

INC

Load Factory Set Enter

DEC

START

BATT TYPE LiPo

ENTER

[ BATT MEMORY 1 ] C:4.9A D:2.2A

LiPo BALANCE CHG

4.9A 7.4V(2S)

START

BATT TYPE MiMH

ENTER

[ BATT MEMORY 2 ] NiMH 2.4V (2S )

NiMH CHARGE CURRENT 1.0A

START

BATT TYPE Pb

ENTER

ENTER CHARGER LOAD……

INC

LiPo FAST CHG

2.0A 7.4V (2S)

DEC

INC

LiFe FAST CHG

2.0A 6.6V (2S)

DEC

INC

Lilo FAST CHG

2.0A 7.2V (2S)

DEC

INC

LiHV FAST CHG

2.0A 7.6V (2S)

DEC

INC

NiMH DISCHARGE

0.1A CUT: 1.0V

DEC

INC

NiCd DISCHARGE

0.1A CUT: 1.0V

DEC

INC

Capacity Cut-Off ON 5000mAH

DEC

INC

DEC

INC

BATT VOLTAGE

7.4V ( 2S )

DEC

[ BATT MEMORY 1 ] LiPo 7.4V (2S )

INC

LiPo CHARGE

4.9A 7.4V(2S)

DEC

INC

BATT VOLTS

2.4V (2S)

DEC

SAVE PROGRAM SAVE….

INC

NiMH Auto CHARGE CURRENT 1.2A

DEC

INC

BATT VOLTS

4.0V (2P)

DEC

[ BATT MEMORY 3 ] C:3.3A D:1.5A

STARG/ENTER>3s

DC Input Low CUT-OFF 11.0V

INC

LiPo STORAGE

2.0A 7.4V (2S)

DEC

INC

LiFe STORAGE

2.0A 6.6V (2S)

DEC

INC

Lilo STORAGE

2.0A 7.2V (2S)

DEC

INC

LiHV STORAGE

2.0A 7.6V (2S)

DEC

INC

NiMH RE-PEAK 1

DEC

INC

NiCd RE-PEAK 1

DEC

INC

Temp Cut-Off ON 50°C 122°F

DEC

INC

Key Beep ON Voice ON

DEC

INC

CHARGE CURRENT

4.9A

DEC

SAVE PROGRAM SAVE….

INC

LiPo FAST CHARGE

4.9A 7.4V(2S)

DEC

INC

CHARGE CURRENT

3.3A

DEC

START

SAVE PROGRAM

ENTER

INC

NiMH DISCHARGE

1.0A CUT: 2.0V

DEC

INC

CHARGE CURRENT

3.3A

DEC

[ BATT MEMORY 3 ] Pb 4.0V (2S )

ENTER

INC

LiPo DISCHARGE

2.0A 7.4V (2S)

DEC

INC

LiFe DISCHARGE

2.0A 6.6V (2S)

DEC

INC

Lilo DISCHARGE

2.0A 7.2V (2S)

DEC

INC

LiHV DISCHARGE

2.0A 7.6V (2S)

DEC

INC

NiMH CYCLE CHG>DCHG 1

DEC

INC

NiCd CYCLE CHG>DCHG  1

DEC

INC

Temperature Unit Celsius

DEC

INC

NiCd Sensitivity D.Peak  4mV

DEC

INC

DISCHG CURRENT

2.2A

DEC

START

SAVE PROGRAM ENTER

ENTER

INC

LiPo STORAGE

4.9A 7.4V(2S)

DEC

INC

TRICKLE 100mA

DEC

INC

DSCH VOLTAGE

1.1V/CELL

DEC

INC

NiMH RE-PEAK 2

DEC

INC

DSCH CURRENT

1.5A

DEC

SAVE PROGRAM SAVE….

INC

Rest Time CHG>DCHG 10Min

DEC

INC

NiMH Sensitivity D.Peak  4mV

DEC

INC

DISCHG VOLTAGE

3.0V/CELL

DEC

INC

TVC=YOUR RISK !

4.20V

DEC

INC

LiPo DISCHARGE

2.2A 7.4V(2S)

DEC

INC

PEAK DELAY 1Min

DEC

INC

DSCH CURRENT

2.2A

DEC

INC

NiMH CYCLE DCHG>CHG 1

DEC

INC

DSCH VOLTAGE

1.7V/CELL

DEC

START

SAVE PROGRAM

ENTER

DECINC

ENTER

D100v2

09 ·

Explanation of Buttons

CH A/CH B: It is used to switch from Channel A to B or vice versa.

BATT PROG / STOP Button: It is used to stop the progress or go back to previous step/screen

DEC Button: It is used to go through the menus and decrease the parameter value

INC Button: It is used to go through the menus and increase the parameter value

ENTER / START Button: It is used to enter parameter, store parameter on screen and start the program.

When you are willing to alter the parameter value in the program, press the START/ENTER button to make it blink then change the value by pressing DEC and INC button. The value will be stored by re-pressing the START/ENTER button. If there is another parameter can be altered in the same screen, when you confirm the first parameter value, the next parameter value will start to blink which means it is ready to alert.

When you are willing to start the process, press and hold the START/ENTER button for 3 seconds. When you are willing to stop the progress or go back to previous step/screen, press the BATT PROG/STOP button once.

· 10

D100v2

Power and Battery Connection

1. Connecting to power source

There are two kinds of inputs for SKYRC D100v2, DC 11-18V and AC 100-240V.

AC 100-240V power source connection.

12V DC Battery / DC power supply connection.

XT60

D100v2

11 ·

Power and Battery Connection

Note: We will explain the operating procedure of one channel as the procedure for channel A and B is identical.

2. Connecting the battery

TO AVOID SHORT CIRCUITS, ALWAYS CONNECT THE CHARGE LEADS TO THE CHARGER FIRST, AND THEN TO THE BATTERY. REVERSE THE

WARNING!

SEQUENCE WHEN DISCONNECTING THE PACK.

1) LiPo Battery Connection with Balance Adapter

LiPo

Balance Socket

For safety reasons, the default setting for charging Lithium (LiPo, Lilon, LiFe and LiHV) battery is using balance adaptor to connect battery and charger in Charge, Fast Charge, Balance Charge, Discharge and Storage modes. But if the battery comes without balance wire,please proceed with the prompting message "No balance cable detected, push enter to continue".

The balance wire attached to the battery must be connected to the charger with the black wire aligned with the negative marking. Ensure correct polarity!

2) NiMH/NiCd or Pb Battery Connection

· 12

NiMH

D100v2

Operating Program

Here is the detailed procedure to make the charger work. All the screens and operations will take Li-Po BALANCE CHARGE program for example,

Note: We will explain the operating procedure of one channel as the procedure for channel A and B is identical..

1. Connection

1).

Connecting to power source

There are two kinds of inputs for SKYRC D100v2, DC 11-18V and AC 100-240V.

A. Operating in AC mode

SKYRC D100v2 comes with built-in switching power supply. You can connect the AC power cord directly to the main AC socket. (100-240V AC).

Note: The output power in AC mode is 100W totally for Channel A, Channel B and Power supply.

In AC mode, it supports Power Distribution. The total power for Channel A, Channel B and power supply is 100W. You could set the Max Power for one output port (Take Channel A for example)as following,

DC S UPPLY: 20 W

CH A:50W CHB :30W

DC S UPPLY: 20 W

CH A:50W CHB :30W

Then, the channel B and DC power supply will take the rest power automatically (For example, if you set DC power supply as 20W and Channel A as 50W, the Channel B will take the rest power of 30W.

NOTE1:

NOTE2:

If Channel A/Channel B and DC power supply are both working, you can't change the power for them.

If DC power supply is working, you can change the power of Channel A and Channel B. thus, the DC power supply will take the rest power automatically.

B. Operating in DC mode

Please connect SKYRC D100v2 with AC/DC power supply by supplied DC input cable. Also you could use terminal clips with DC connectors, for attaching directly to 12V car batteries. It is critically important that you use either a fully charged 13.8V car battery or a high-quality AC/DC power supply in the range of 11-18V DC output with minimum power 300W or higher to insure reliable performance.

D100v2

13 ·

Operating Program

Connecting the battery

2). Important!!! Before connecting a battery it is absolutely essential to check one last time that you have set the parameters correctly. If the settings are incorrect, the battery may be damaged, and could even burst into flames or explode. To avoid short circuits between the banana plugs, always connect the charge leads to the charger first, and only then to the battery. Reverse the sequence when disconnecting the pack.

Balance Socket

3).

The balance wire attached to the battery must be connected to the charger with the black wire aligned with the negative marking. Take care to maintain correct polarity! (See the wiring diagram below.) This diagram shows the correct way to connect your battery to the SKYRC D100v2 while charging.

WARNING:

To avoid short circuit between the charge lead always connect the charge cable to the charger first, then connect the battery. Reverse the sequence when disconnecting.

· 14

D100v2

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

(1)

A memory profile is available for setting and storing pertinent information for up to 20 different program sets; each channel can store 10 program. Once a battery program is stored into memory, it will be retained until changed again manually. Recalling a program memory number makes the charger instantly ready to go!

(2)

If you do not wish to use the battery program memories, this charger can be manually set before each use.

The following flowchart shows how the program is set manually:

BATT/PROGRAM

LiPo BATT

STA RT/ EN TE R

BATT/PROGRAM Select Press INC and DEC to go through all the programs and press

START/ENTER to enter LiPo BATT Program.

LiPo BALANCE

2.0A 11.1V (3S)

STA RT/ EN TE R

LiPo BALANCE

2.0A 11.1V (3S)

STA RT/ EN TE R

LiPo BALANCE

2.0A 11.1V (3S)

STA RT/ EN TE R

LiPo BALANCE

2.0A 11.1V (3S)

STA RT/ EN TE R > 3 Se co nd s

Mode Select Press INC and DEC to go through all the modes and press START/ENTER to enter LiPo Balance Charge Mode.

Battery Setting

Press START/ENTER, the present value will start to blink. Press

INC and DEC to change the value and press START/ENTER to

confirm your setting.

At the same time, the battery pack’s cell count will start to blink,

press INC and DEC to change the value and press START/

ENTER to confirm your setting.

Program Start

Press and hold START/ENTER for 3 seconds to start the

program.

D100v2

15 ·

Lithium Battery Program(LiPo/LiFe/Lilon/LiHV)

BATTERY CHECK

WAIT...

R:3SER S:3SER

CANCEL(STOP)

The charger is detecting the battery cell.

R shows the number of cells detected by the charger and S is the number of cells set by you on the previous screen. If the two numbers are not identical, press STOP to go back to the previous screen to recheck the number of cells of the battery pack that you set before going ahead.

R:3SER S:3SER

CONFIRM(ENTER)

STA RT/ EN TE R

Lp3s 1.5A 12.14V

BAL 000:50 00022

[ END: FINISH ]

16.8V 2600mAh

R shows the number of cells detected by the charger and S is the number of cells set by you on the previous screen. If the two numbers are identical, press START/ENTER to start the charging process.

Charging Status Monitor

During charge process, real-time status will be shown as seen on the left.

Program Complete

Once the battery is fully charged, the screen will read “END: FINISH” and the charger will emit a ringing sound. The charger

[ Time: 00: 45: 32 ]

16.8V 2600mAh

also displays battery voltage, charged capacity and elapsed time.

Program Stop During the charging process, press STOP to stop the charging process.

Video Tutorial

· 16

Please scan and watch the tutorial video about how to charge LiPo battery in balance mode.

D100v2

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

VARIOUS INFORMATION DURING THE PROCESS

Press INC or DEC during the charging or discharging process to view further pertinent information on the LCD screen.

Lp3s 1.5A 12.14V

BAL 000:50 00022

INC

4.07 4.06 4.11 V

0.00 0.00 0.00 V

INC

Fuel= 90%

Cell= 4.10V

Lp3s 1.5A 12.14V

BAL 000:50 00022

End Voltage

12.6V(3S)

IN Power Voltage

12.56V

Ext. Temp ---Int. Temp 37°C

Temp Cut-Off 　　　 50C

Safety Timer ON 200min

Capacity Cut-Off ON 5000mAh

DEC

Real-time status: battery type, battery cell count, charge current, battery pack total voltage,working mode, elapsed time and charged capacity.

Voltage of each cell in the battery pack when the battery is connected with balance lead.

Charged capacity percentage and average cell voltage of the battery pack.

Final voltage when the program ends.

Input voltage.

Internal temperature. Temperature probe needs to be connected to show external temperature.

Cut-off temperature.

Safety timer ON and duration of time in minutes.

Capacity cut-off ON and value of the set capacity limit.

D100v2

17 ·

NiMH/NiCd Battery Program

NiMH/NiCd:

This program is only suitable for charging/discharging NiMH/NiCd batteries. The D100v2 offers the following NiMH/NiCd charge modes: Charge, Auto Charge, Discharge, Re-Peak and Cycle.

Selecting the Battery Type:

After powering on the D100v2, press the INC or DEC button repeatedly until you reach the appropriate program for the battery type you wish to charge. For this example we have chosen the “NiMH BATT“ or “NiCd BATT” program. Now press the ENTER button to enter the desired program.

BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE YOU ARE CHARGING NIMH/NICD BATTERIES. CHARGING LIPO BATTERY UNDER NIMH/

WARNING!

NiMH/NiCd Charge Mode:

BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTOOD ALL OF THE WARNINGS AND SAFETY INFORMATION CONTAINED ON PAGES 06-08.

After selecting the correct battery type, if the screen does not read “CHARGE”, use the DEC or INC buttons to change it to the “CHARGE” mode.

NICD BATTERY PROGRAM WILL CAUSE FIRE.

NiMH CHARGE

CURRENT 2.0A

STA RT/ EN TE R

Press the ENTER button and the amp rate value will begin blinking.

Use the DEC or INC button to adjust the value to the desired rate.

Follow the instructions provided on your battery when setting the

charge current.

Press and hold the ENTER button for 3 seconds to start charging.

NiMH 2.0A 5.42V

CHG 002:22 00106

Once charging has commenced, the charger will display the

following real-time information: battery type, charging current, battery

voltage, working mode, elapsed time and charged capacity. Once

the battery is fully charged, the screen will read "END: FINISHED"

and the charger will emit a ringing sound. You can press the STOP

button at any time during the charging process to stop charging.

NiMH/NiCd Auto Charge Mode:

In this mode, the charger automatically detects the connected NiMH or NiCD battery and determines the proper full charge and cut-off thresholds. Setting the upper charge current limit for safe levels based on your battery specifications will ensure safe charging of your specific battery. If you are unsure of the maximum allowable charge rates, set the charger to a maximum of 1C (battery mAh/1000, e.g. 3200mAh = 3.2A).

· 18

D100v2

NiMH/NiCd Battery Program

NiMH Auto CHARGE CURRENT 1.3A

After selecting the correct battery type, use the INC or DEC button to change the charge mode to the “Auto CHARGE” setting.

Press the START button and the amp rate value will begin

STA RT/ EN TE R

flashing. Use the INC or DEC button to adjust the value to the desired rate. Follow the instructions provided on your battery when setting the upper charge amperage rate.

Press and hold the START button for 3 seconds to start charging.

NiMH 1.3A 5.42V AUT 002:22 00106

Once charging has commenced, the charger will display the following real-time information: battery type, charging current, battery voltage, elapsed time and charged capacity.

Once the battery is fully charged, the screen will read “END: FINISHED” and the charger will emit a ringing sound. You can press the STOP button at any time during the charging process to stop charging.

NiMH/NiCd Discharge Mode:

NiMH DISCHARGE

1.3A CUT:9.6V

After selecting the correct battery type, use the INC or DEC button to select the “DISCHARGE” mode. Press the START button and the amp rate value will begin flashing. Use the INC or DEC buttons to adjust the value to the desired discharge rate. Press the START button again and the voltage cut-off will begin to flash. Use the INC or DEC button to adjust the value to the desired rate.

Follow the instructions provided on your battery when setting the voltage cut-off. The D100v2 will stop discharging when the battery has reached the preset voltage cut-off.

NiMH 1.3A 10.42V AUT 002:22 00106

D100v2

Press and hold the START button for 3 seconds to start discharging. Once discharging has commenced, the charger will display the following real-time information: battery type, discharging current, battery voltage, working mode,elapsed time and discharged capacity.

19 ·

NiMH/NiCd Battery Program

[ TIME: 00:04:04 ]

9.6V 00640mAh

When discharging is complete, the screen will read “END:

CUTOFF-VOL” and the charger will emit a ringing sound.

The charger will display the elapsed time, end voltage and the

discharged capacity in mAh.

You can press the STOP button at any time during the

discharging process to stop the discharge process.

NiMH/NiCd Re-Peak Mode:

Applicable to NiMH and NiCD batteries only, in re-peak mode the charger can peakcharge the battery once, twice, or three times in a row automatically. This process is good for confirming that the battery is fully charged and for verifying how well the battery can accept a fast charge. A five-minute cool-down delay occurs after each re-peak charge.

IN RE-PEAK MODE, THE D100 V2 USES THE CHARGE AMPERAGE AND VOLTAGE SETTINGS ENTERED IN CHARGE MODE.

NiMH RE-PEAK 2

After selecting the correct battery type, use the INC or DEC

button to select the “RE-PEAK” mode. Press the START button

and the Re-peak cycle number 1 begins to flash on the screen.

Use the INC or DEC button to scroll through the cycle count and

STA RT/ EN TE R

set a number between 1 and 3.

Press and hold the START button for 3 seconds to start the re-

peak process.

NiMH 1.3A 10.42V RPC 004:04 00686

Once the Re-Peak process has begun, the charger will display

the following real-time information: battery type, charging

current, battery voltage, elapsed time and charged capacity.

Once the Re-Peak process has completed, the screen will read

“END: RE-PEAK” and the charger will emit a ringing sound. The

charger will display the charge/discharge capacity for each

cycle. Using the + and - buttons, you can scroll through the

history data of each cycle.

· 20

D100v2

NiMH/NiCd Battery Program

NiMH/NiCd Cycle Mode:

The D100v2 makes cycling of NiMH/NiCd batteries easy. The process of discharging and recharging (cycling) can be performed automatically with one simple step and will improve the performance of NiMH/NiCd batteries. We strongly recommend cycling any battery that has been discharged and stored for a period of time. This will increase the remaining usable battery life and also improve the battery performance.

NiMH CYCLE DCHG > CHG 2

After selecting the correct battery type, use the INC or DEC button to select the “CYCLE” mode. The Cycle Mode gives you two cycling options: “DCHG>CHG” or “CHG>DCHG“. The

STA RT/ EN TE R

NiMH CYCLE CHG > DCHG 5

“DCHG>CHG” option will first discharge the battery and then recharge the battery.

The “CHG>DCHG” option will first charge the battery and then discharge the battery. If this screen does not show your desired cycling option, press the START button once and this setting will begin flashing. Use the INC or DEC button to change this setting.

Pressing the START button again will cause the cycle count to begin flashing. Use the INC or DEC button to change this to the number of cycles you want the D100v2 to run. The D100v2 can cycle the battery a maximum of 5 times consecutively. Press and hold the START button for 3 seconds to start the Cycle Mode.

NiMH 0.5A 9.6V D > C 004:04 00034

Once cycling has commenced, the charger will display the following real-time information: battery type, charging/ discharging current, battery voltage, working mode,elapsed time and charged/discharged capacity. You will also see “D>C“ or “C>D“. This will indicate which cycling order you have chosen. Either “D“ or “C“ will be flashing. This flashing indicates which part of the cycle is currently being executed.

Once the cycling process is complete, the screen will read “END: CYCLE” and the charger will emit a ringing sound. The D100v2 will display the charged/discharged capacity for each cycle. Using the + and - buttons, you can scroll through this data for each cycle.

D100v2

21 ·

Pb Lead-Acid Battery Program

Additional NiMH/NiCd Process Information:

During the NiMH/NiCd battery charging/discharging process the D100v2 can display a variety of information. Using the INC or DEC buttons, you can also view the following information:

NiMH Sensitivity D.Peak 4mV/CELL

Delta Peak Voltage Sensitivity setting

In Power Voltage

12.56V

Input Voltage

Ext. Temp ---Int. Temp 37 C

Safety Timer ON 200min

External*/ internal temperature

Safety timer setting

Temp Cut-off

50 C/122 F

Capacity Cut-Off ON 5000mAh

Temperature cut-off

Capacity limit setting

Pb Lead-Acid Battery Program

Pb (Lead-Acid):

BATT/PROGRAM Pb BATT

Pb Charge Mode:

After selecting the correct battery type, use the INC or DEC button to change it to the “CHARGE“ mode. Press the START button and the amp rate value will begin flashing. Use the INC or DEC buttons to adjust the value to the desired charge rate. The amp rate should be set to 1/10th of capacity. For example, if you are charging a 20Ah battery the charge rate should be set to 2A. Follow the instructions provided on your battery when setting the amp rate.

This program is only suitable for charging Pb(lead-acid) batteries with nominal voltage ranging from 2 to 20V which are significantly different from NiMH/NiCd batteries. Pb batteries are suggested to charge with a low current of 0.1C and cannot be used for fast charging. Please follow the instructions provided by the battery manufacturer.

The D100v2 offers the following Pb charge modes: Charge and Discharge.

· 22

D100v2

Pb Lead-Acid Battery Program

Pb Charge

1.5A 12.0V(6P)

Press the START button again and the nominal battery pack voltage will begin flashing. Use the INC or DEC button to set the voltage and the number of cells. Press and hold the START button for 3 seconds to start charging.

Once charging has commenced, the charger will display the

P-6 1.5A 13.56V CHG 002:22 00106

following real-time information: battery type, charging current, battery voltage, working mode, elapsed time and charged capacity. When charging is complete, the screen will read “FINISHED” and the charger will emit a ringing sound.

Pb Discharge Mode:

After selecting the correct battery type, use the INC or DEC buttons to change it to the “DISCHARGE“ mode. Press the START button and the amp rate value will begin flashing. Use the INC or DEC buttons to adjust the value to the desired discharge rate. Follow the instructions provided with your battery when setting the amp rate.

Pb Discharge

1.5A 12.0V(6P)

Press the START button again and the nominal battery pack voltage will begin flashing. Use the INC or DEC buttons to set the voltage and the number of cells. Press and hold the START button and discharging will begin.

P-6 1.0A 13.56V DCH 005:10 00964

Once discharging has commenced, the charger will display the following real-time information: battery type, cell count,discharging current, battery voltage, elapsed time and discharged capacity. When discharging is complete, the screen will read “FINISHED” and the charger will emit a ringing sound.

Additional Pb Process Information:

During the Pb battery charging/discharging process the D100v2 can display a variety of information. Using the INC or DEC buttons you can also view the following information:

Capacity Cut-Off ON 5000mAh

Capacity cutoff setting

Safety Timer ON 200min

Safety timer setting

Temp Cut-off 50 C

In Power Voltage

12.56V

D100v2

Temperature cut-off

Input voltage

Ext. Temp ---Int. Temp 37 C

External*/ internal temperature

23 ·

DC Power Supply

To use D100v2 as a power supply, the user must connect it to AC power source. When the green LED on the back side turns on, then the user is free to use the power supply, the power of DC output is adjustable from 10W to 100W. The output voltage is 13.8V. The power of DC output is shared with charger power. When you increase the power of DC output, the charger power will be decreased accordingly. (DC Power + Channel A+Channel B = 100 Watts)

EXPLANATION OF LED STATUS

Operating Instruction

BATT/PROGRAM SYSTEM SETTING->

ENTER

DC SUPPLY: 20W CHA: 50 CHB: 30W

ENTER

CH1: 50 CH2: 50W DC SUPPLY: 150W

OFF

Green

Yellow

Red

Red Blinking

Press the ENTER to enter the DC Power Supply program

Set the output power for the DC charger or other devices. (please note the voltage is 13.8V)

Set the power of channel A and channel B, the power supply will take the rest power automatically.

DC Power Off

0-30% Loading

31-60% Loading

61-100% Loading

Over Load

Caution: The maximum DC Power output is 100 Watts. Please check the total loading of your equipments before using DC power supply.

If the DC power supply is over load, the led light will flash red and stop working.

Please scan and watch the tutorial video about using DC power supply.

Video Tutorial

· 24

D100v2

Battery Memory Set and Call Out

The charger can store up to 20 different charge/discharge profiles(each channel 10 sets) for your convenience, and the stored profiles can be recalled quickly without having to go through the setup process.

When you are willing to alter the parameter value in the program, press START/ENTER to make it blink then change the value with INC or DEC. The value will be stored by pressing START/ENTER once. Note: All following screen are taking 6S(22.2V) LiPo battery for example.

1. Battery Memory Set

[ BA T T M E M O R Y 1 ] EN T E R S E T - >

STA RT/E NT ER

B AT T T Y P E L iP o

DE C I NC

Enter the battery memory program. (10 different charge/discharge profiles can be stored in each channel).

Set the battery type(LiPo/LiFe/LiIon/LiHV/NiMH/NiCd/Pb).

B AT T V O L T A GE 22 . 2 V ( 6 S )

DE C I NC

C HA R G E C U R RE N T

5. 0 A

DE C I NC

D IS C H G C U R RE N T

2. 0 A

DE C I NC

D IS C H G V O L TA G E

3. 0 V / C E L L

DE C I NC

T VC = Y O U R R IS K !

4. 2 0 V

DE C I NC

S AV E P R O G R AM EN T E R

STA RT/E NT ER

D100v2

Set the voltage and number of cells(1S-6S).

Set the charge current(0.1-10.0A).

Set the discharge current (0.1A-2.0A).

Set the discharge voltage(3.0-3.3V/Cell).

Set the terminal voltage(4.18-4.25V).

Press ENTER to save program.

25 ·

Battery Memory Set and Call Out

S AV E P R O G R A M S AV E .

[ B AT T M E M O R Y 1 ] L iP o  2 2 . 2 V ( 6 S )

Indicate the battery type and battery cell of the saved profile.

2. Battery Memory Call Out

[ B AT T M E M O R Y 1 ] C :5 . 0 A D : 2 . 0A

DE C I NC

[ B AT T M E M O R Y 1 ] C :5 . 0 A D : 2 . 0A

START/ENTER >2 Seconds

L iP o B A L A N C E C HG 5 .0 A 2 2 . 2 V ( 6 S)

Please scan and watch the tutorial video about how to set battery memory and call out.

Video Tutorial

Press the DEC/INC to select memory number.

e.g. Select memory 1 Press and hold the START/ENTER for 2 seconds to call out the memory.

Press START/ENTER for 3 seconds to start the process.

· 26

D100v2

System Setting

It will be operated with the default value of the essential user settings when it is powered on for the first time.The screen displays the following information in sequence and the user can change the value of parameter on each screen. When you are willing to alter the parameter value in the program, press START/ENTER to make it blink then change the value with INC or DEC. The value will be stored by pressing START/ENTER once.

ITEM

D C SU P P L Y : O F F C H1 : 5 0 C H 2 : 5 0W

S af e t y T i m e r O N 12 0 M i n

C ap a c i t y C u t -O f f O N 50 0 0 m A H

T em p C u t - O f f O N 50 C 1 2 2 F

T em p e r a t u r e Un i t Ce l s i u s

SELECTION DESCRIPTION

In AC mode, it supports Power Distribution.

OFF/ 10-100W

OFF/ ON (1-720 Min)

OFF/ ON (100-50000 mAh)

OFF/ ON (20 C/68 F 80 C/176 F)

Celsius Fahrenheit

The total power for Channel A / Channel B and DC supply is 100W. You could set the AC Max Power for one output.

When you start a charge process, the integral safety timer automatically starts ru nn ing at th e s ame ti me. This is programmed to prevent overcharge the battery if it proves to be faulty, or if the termination circuit cannot detect the battery full. The value for the safety timer should be generous enough to allow a full charge of the battery.

This program sets the maximum charge capacity that will be supplied to the battery during charge. If the delta peak voltage is not detected nor the safety timer expired by any reason, this feature will automatically stop the process at the selected capacity value.

The battery's internal chemical reaction will cause the temperature of the battery to rise. If the temperature limit is reached, the process will be terminated.

You can choose the temperature displayed by Celsius or Fahrenheit as you like.

D100v2

27 ·

System Setting

ITEM

R es t T i m e C HG > D C H G 1 0 M in

N iM HS e n s i t i vi t y D .P e a k  4 m V

N iC dS e n s i t i vi t y D .P e a k  4 m V

K ey B e e p O N V oi c e O N

D C In p u t L o w C ut - O f f 1 1 . 0V

L oa d F a c t o r y S et En t e r

V er s i o n H W: 1 . 0 0 F W : 2 . 00

SELECTION DESCRIPTION

1-60Min

Default: 4mV/Cell 3-15mV/Cell

OFF/ON

10.0-12.0V

A rest time allowing the battery to cool down between charging/discharging cycle.

This program is for NiMH/NiCd battery only. When the charger detects the delta peak value reaches the value you set, the charger will say the battery is fully charged.

The beep sounds at every time touching the buttons to confirm your action. The beep or melody sounded at various times during operation to alert different mode changes.

This program monitors the voltage of input battery. If the voltage drops below the value you set the operation forcibly terminated to protect the input battery.

Press ENTER to load factory default setting.

It indicates the hardware and firmware version.

· 28

D100v2

Battery Voltage Meter

The user can check battery's total voltage, the highest voltage, the lowest voltage and each cell's voltage. Please connect the battery to the charger main battery lead to battery socket and balance wires to balance socket.

This diagram shows the correct way to connect

4.1 9 4.1 5 4.1 8V

4.1 5 4.1 9 4.1 8V

4.1 9 4.1 5 4.1 8V

4.1 5 4.1 9 4.1 8V

your battery to check the voltage.

B AT T / P R O G R AM B AT T M E T E R

START ENT ER

4 .2 0 4 . 1 9 4 . 1 9 V 4 .1 8 4 . 1 8 4 . 1 9 V

DE C

IN C

M AI N 2 5 . 1 3 V H 4. 2 0 0 V L 4 . 1 82 V

D100v2

Press the START/ENTER to enter the Lithium Battery Meter program.

The screen indicate each cell's voltage.

The screen indicate the total voltage, the highest voltage and the lowest voltage.

29 ·

Battery Resistance Meter

The user can check battery's total resistance, the highest resistance, the lowest resistance and each cell's resistance. Please connect the battery to the charger main battery lead to battery socket and balance wires to balance socket.

This diagram shows the

00 5 0 03 0 0 3 mΩ

correct way to connect your battery to check the resistance.

B AT T / P R O G R AM B AT T R E S I S T A NC E

Sta rt Ent er

0 12 0 0 5 0 0 5 mΩ

0 06 mΩ

DE C

IN C

T AT A L :2 8 mΩ

H :12 mΩ L :5 mΩ

· 30

Press the START/ENTER to enter the Lithium Battery Resistance program.

The screen indicate each cell's resistance.

The screen indicate the total resistance, the highest resistance and the lowest resistance.

D100v2

Controlling the Charger Using the App

The Bluetooth 4.0 connectivity allows the user to control and monitor the D100v2 comfortably through an app on a portable device such as smart phone, iPad, or iPhone. The iOS app can be downloaded from iTunes store, the Android app from Google Play Store. Operation of the app is self-explanatory and the same on iOS and on Android. Explicit pairing is not required; after download and installation just activate Bluetooth on your mobile device and launch the App. D100v2 and your device will establish Bluetooth connection automatically.

Scan the QR code on the right to download the SkyCHARGER App.

OPERATION

Connect the power cord to D100v2, then plug the power cord into the outlet

1. (100~240V AC, 50/60Hz). Connect the batteries to the corresponding channels.

2. Enable Bluetooth function on your mobile device and launch the SkyCHARGER.

1). Launch the App and set the password (Please do not set the password to 5793 which is the reserved for the system using)

Revo

Ver: 1.7.1

SkyCHARGER

15:53

Revo

Battery

Type

LiPo

LiIon

LiFe

15:53

CH. A CH. B

Battery

Cells

Alert

Please setup your password

Ignore OK

Operation

Mode

BAL.CHARGE

CHARGER

DISCHARGER

Scan with your Smartphone to download.

Revo

BACK

Your password must have at least 4 digits

15:53

Edit Password

D100v2

HOME

SCAN TO GO

PROGRAM

SYSTEM

主页

编程

系统

31 ·

Controlling the Charger Using the App

How to reset password

B AT T / P R O G R AM S YS T E M S E T T I NG - >

START ENT ER

D C SU P P L Y : O F F C HA : 5 0 C H B : 5 0

Press ENTER button

Press DEC twice

L oa d F a c t o r y S et EN T E R

Press and hold the ENTER button for 3 seconds to reset password.

2). Operation Steps for Charging(Take 6S LiPo battery for example)

Connect the batteries to the corresponding channels,select battery type, cells. Press “NEXT” to set the proper charge current.

Revo

Battery

HOME

Type

LiPo

LiIon

LiFe

15:53

CH. A CH. B

Battery

Operation

Cells

BAL.CHARGE

CHARGER

DISCHARGER

SCAN TO GO

PROGRAM

Mode

SYSTEM

Revo

Battery

Type

LiPo

15:53

CH. A CH. B

Battery

Cells

BAL.CHARGE

Charge Current

1.1A

1.2A

1.3A

1.4A

1.5A

1.6A

1.7A

START

Operation

Mode

MoreBack

Revo

15:53

CH. A CH. B

Balance Charge

Battery Type

LiPo

Current

4.65

Capacity

Battery Fuel Gauge

Battery ID

0D0E07D5 1

4.09 V 4.10 V 4.10 V

mAh

Battery Cells

Voltage

24.58

Duration

00:10:071500

Charger Temperature

No. of charger

4.09 V 4.10 V 4.10 V

STOP

Please scan and watch the tutorial video about how to control and operate the charger via smartphone.

Video Tutorial

122

· 32

D100v2

Controlling the Charger Using the App

3). How to Use Memory Program

Revo

Battery

Type

LiPo

LiIon

LiFe

15:53

CH. A CH. B

Battery

Operation

Cells

BAL.CHARGE

CHARGER

DISCHARGER

SCAN TO GO

Mode

Revo

15:53

CH. A CH. B

Revo

Battery

Type

LiPo

LiIon

LiFe

Battery

Cells

15:53

EditBACK

Operation

BAL.CHARGE

CHARGER

DISCHARGER

Save

Mode

HOME

Press “PROGRAM” button

Revo

Cancel Edit Save

LiPo 6Cell BAL.CHARGE >

Charge Current

Voltage Cut-Off

Press to save the program after set the charge current and voltage cut-off

PROGRAM

15:53

5.0 A

4.20 V

Please scan and watch the tutorial video about how to use memory program.

Video Tutorial

D100v2

SYSTEM

Enter into PROGRAM interface

Revo

LiPo BAL.CHARGE

Cells： 6 Charge Curretn： 5.0A Voltage：4.20V

HOME

Memory program setting finishes.

15:53

CH. A CH. B

PROGRAM

SYSTEM

Set battery type, cells and working modes

Revo

LiPo BAL.CHARGE

Cells： 6 Charge Curretn： 5.0A Voltage：4.20V

HOME

Press“START”button to start charge Press“EDIT” button to change the setting

15:53

CH. A CH. B

START EDIT CANCEL

PROGRAM

SYSTEM

33 ·

Controlling the Charger Using the App

4). System Setting

Revo

Battery

Type

LiPo

LiIon

LiFe

15:53

CH. A CH. B

Battery

Operation

Cells

BAL.CHARGE

CHARGER

DISCHARGER

SCAN TO GO

Mode

Revo

Safety Timer

15:53

CH. A CH. B CH. A CH. B

Revo

120 Min

Capacity Cut-Off

5000 mAh

Temperature Cut-Off

122

Rest Time Between Cycle

Charge

10 Min

Discharge

DC Input Low Cut-Off

11.0

Balance Port Enable

Change Password >

Key Beep

Buzzer

15:53

HOME

PROGRAM

SYSTEM

HOME PROGRAM

PROGRAM

SYSTEM

HOME

Enter into System Setting

5). SCAN TO GO

Using your smart phone and launch “SkyCharger” App. Since all the essential information is stored in the QR Code. All you need to do is press the Scan button, and the charge or discharge process will start automatically.

· 34

SYSTEM

D100v2

Controlling the Charger Using the App

How to print QR code

Revo

LiPo BAL.CHARGE

Cells： 6 Charge Curretn： 5.0A Voltage：4.20V

CH. A

CH. B CH. C CH. D

15:53

Revo

LiPo BAL.CHARGE

Cells： 6 Charge Curretn： 5.0A Voltage：4.20V

CH. A

CH. B CH. C CH. D

15:53

Revo

5.0A

15:53

Press the QR code

Revo

15:53

Select the QR code and open it You can print it from your mobile phone

Scan to charge

Revo

Battery

15:53

CH. A

CH. B

Battery

Cells

PROGRAM

Operation

BAL.CHARGE

CHARGER

DISCHARGER

SCAN TO GO

Mode

SYSTEM

Type

LiPo

LiIon

LiFe

HOME

Press”SCAN TO GO” Scan to launch the program

Save the QR code to Gallery

Revo

or send the QR code image to computer to print it out.

Revo

BACK

15:53

SkyRC Charger

Please Select Channel

A B

Select corresponding channels

Open Gallery

5.0A

Attach the printed QR code to the battery

Revo

BACK

15:53

Channel A

Align QR Code/Barcode within frame to scan

Please scan and watch the tutorial video about how to use SCAN TO GO.

Video Tutorial

Gallery

D100v2

35 ·

Warning and Error Message

In case of an error the screen will display the cause of error and emit an audible sound.

Incorrect polarity connected.

The battery is interrupted.

C ON N E C T E R R O R C HE C K M A I N P O R T

N O PO W E R D IS T R I B U T E D

D C IN T O O L O W

D C IN T O O H I G H

C EL L E R R O R L OW V O L T A G E

C EL L E R R O R H IG H V O L T A G E

C EL L E R R O R V OL T A G E - I N VA L I D

I NT . T E M P . T OO H I

E XT . T E M P . T OO H I

O VE R C H A R G E C AP A C I T Y L I M IT

O VE R T I M E L I M I T

B AT T E R Y W A S F U LL

Thebattery connection is wrong.

No power allocate to the charger.

Input voltage less than 11V.

Input voltage higher than 18V.

Voltage of one cell in the battery pack is too low.

Voltage of one cell in the battery pack is too high.

Voltage of one cell in the battery pack is invalid.

The internal temperature of the unit goes too high.

The external temperature of the battery goes too high.

The battery capacity is more than the maximum capacity which the user sets.

The charging time is longer than the maximum charging time which the user sets.

The battery voltage is higher than the maximum voltage which the user sets when charging in balance mode.

· 36

D100v2

Using The Charge Control Software “Charge Master”

The free “Charge Master” software gives you unparalleled ability to operate the charger through the computer. You can monitor pack voltage, cell voltage and other data during the charging, view charge data in real-time graphs. And you can initiate, control charging from “Charge Master”. In order to connect the charger to the computer and use the “Charge Master”, you are required to use a USB cable which is not included in this package. The cable must be terminated on one end with “A” plug and the opposite end is terminated with “micro-B” plug which can connect to charger directly. You can control, monitor, operate two channels with one computer. The “Charge Master” can be download from www.skyrc.com.

THESETCONTAINS

1. SKYRC D100v2 Charger

2. XH Adaptor X 2

3. Charging Cable X 2

4. Banana connectors with XT60 connector Charging Cable X 2

5. Power Cord

D100v2

37 ·

Specification

DC Input Voltage : 11-18V AC Input Voltage: 100-240V Display Type: 128x64 LCD Display Backlight: Cool White Case Material: Plastic Controls: Five Buttons Case Size: 153x140x67mm Weight: 668g DC Power Supply Output: 13.8V / Max. 100W PC Communications: USB Port for PC Control & Firmware Upgrade External Port: 2-6S Balance Socket-XH, Temperature Probe Socket, Battery Socket, AC/DC Input, DC Output, Micro USB Port for PC, 5V-2.1A USB Output. Delta Peak Detection for NiMH/NiCd: 3-15mV/cell / Default: 4mV/cell Charge Cut-off Temperature: 20ºC/68ºF-80ºC/176ºF(adjustable) Charge Voltage: NiMH/NiCd: Delta peak detection  LiPo: 4.18-4.25V/cell LiIon: 4.08-4.2V/cell LiFe: 3.58-3.7V/cell LiHV: 4.25-4.35V/cell Balance Current: 300mA/cell Reading Voltage Range: 0.1-26.1V Battery Types/Cells: LiPo/LiIon/LiFe/LiHV: 1-6cells NiMH/NiCd: 1-15cells  Pb: 2-20V Battery Capacity Range: NiMH/NiCd: 100-50000mAh LiPo/LiIon/LiFe/LiHV: 100-50000mAh Pb: 100-50000mAh Charge Current: (0.1A-10.0A) x2 Safety Timer: 1-720minutes / OFF Charge Wattage: AC 100W(Support Power Distribution) DC 100Wx2 Discharge Current: (0.1A-2.0A) x2 Discharge Cut-off Voltage: NiMH/NiCd: 0.1-1.1V/cell LiPo: 3.0-3.3V/cell LiIon: 2.9-3.2V/cell LiFe: 2.6-2.9V/cell LiHV: 3.1-3.4V/cell Pb: 1.8-2.0V/cell Discharge Wattage: 10Wx2 Balance Cells: 2-6 cells Memory: 10x2 Different Charge/Discharge Profiles Charge Method: CC/CV for Lithium Types and Lead (Pb) Batteries Delta-peak Sensitivity for NiMH/NiCd.

· 38

D100v2

Regulatory Information

D100v2 satisfy all relevant and mandatory CE directives and FCC Part 15 Subpart B: 2016. For CE directives: The product has been tested to meet the following technical standards:

EN 55014-1:2006+ A1:2009+A2:2011

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 300 328 V2.1.1

EN 301489-1 EN 301489-17

EN 62479

EN 60950-1

Electromagnetic Compatibility- Requirements for household appliances, electric tools and similar apparatus- Part 1: Emission

Electromagnetic Compatibility- Requirements For Household Appliances, Electric Tools And Similar Apparatus- Part 2: Immunity Product Family Standard

Electromagnetic Compatibility (EMC) Part 3-2: Limits for harmonic current emissions(Equipment input current up to and including 16A per phase)

Electromagnetic Compatibility (EMC) Part 3-3: Limitation of voltage supply systems for equipment with rated current≤16A

Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements. Part 17: Specific conditions for Broadband Data Transmission Systems.

Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 Ghz).

Information Technology Equipment-Safety- Part 1: General Requirements

This symbol means that you must dispose of electrical from the General household waste

when it reaches the end of its useful life. Take your charger to your local waste collection

point or recycling centre. This applies to all countries of the European Union, and to other

European countries with a separate waste collection system.

D100v2

39 ·

Regulatory Information

FCC Note:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or change to this equipment. Such modifications or change could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

App store is a service make of Apple Inc.

Android and Google Play are trademarks of Google Inc.

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SkyRC is under license.

· 40

D100v2

Commonly Used Terms

Commonly used terms

Final charge voltage: the voltage at which the battery's charge limit (capacity limit) is reached. The charge process switches from a high current to a low maintenance rate (trickle charge) at this point. From this point on further high current charging would cause overheating and eventual terminal damage to the pack.

Final discharge voltage: the voltage at which the battery's discharge limit is reached. The chemical composition of the batteries determines the level of this voltage. Below this voltage the battery enters the deep discharge zone. Individual cells within the pack may become reverse polarized in this condition, and this can cause permanent damage.

A, mA: unit of measurement relating to charge or discharge current.1000 mA = 1 A (A=Ampere,mA=Milliampere)

Ah, mAh: unit of measurement for the capacity of a battery (Amperes x time unit; h = hour). If a pack is charged for one hour at a current of 2 A, it has been fed 2 Ah of energy. It receives the same quantity of charge (2 Ah) if it is charged for 4 hours at 0.5 A, or 15 minutes (=1/4 h) at 8 A.

'C'-rating: Capacity is also referred to as the 'C' rating. Some battery suppliers recommend charge and discharge currents based on the battery 'C' rating. A battery's '1C' current is the same number as the battery's rated capacity number, but noted in mA or amps. A 600mAh battery has a 1C current value of 600mA, and a 3C current value of (3 x 600mA) 1800mA or

1.8A. The 1C current value for a 3200mAh battery would be 3200mA (3.2A).

Nominal voltage(V): The nominal voltage of the battery pack can be determined as follows;

-.NiCd or NiMH: multiply the total number of cells in the pack by 1.2. A 8-cell pack will have a nominal voltage of 9.6 volts (8x1.2).

-.LiPo: multiply the total number of cells in the pack by 3.7. A 3-cell LiPo wired in series will have a nominal voltage of 11.1 volts (3x3.7).

-.LiIo: multiply the total number of cells in the pack by 3.6. A 2-cell LiIo wired in series will have a nominal voltage of 7.2 volts (2x3.6).

-.LiFe: multiply the total number of cells in the pack by 3.3. A 4-cell LiIo wired in series will have a nominal voltage of 13.2 volts (4x3.3).

-.LiHV: multiply the total number of cells in the pack by 3.7V. A 4-cell LiHV wired in series will have a nominal voltage of 14.8 volts (4x3.7). If the nominal voltage of the battery is not printed on the battery's label, consult your battery manufacturer or supplier. Do not guess the rated voltage of battery.

D100v2

41 ·

Warranty And Service

Liability exclusion

This charger is designed and approved exclusively for use with the types of battery stated in this Instruction Manual. SkyRC accepts no liability of any kind if the charger is used for any purpose other than that stated. We are unable to ensure that you follow the instructions supplied with the charger, and we have no control over the methods you employ for using, operating and maintaining the device. For this reason we are obliged to deny all liability for loss, damage or costs which are incurred due to the incompetent or incorrect use and operation of our products, or which are connected with such operation in any way.Unless otherwise prescribed by law, our obligation to pay compensation, regardless of the legal argument employed, is limited to the invoice value of those SkyRC products which were immediately and directly involved in the event in which the damage occurred.

Warranty and service

We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. During that period, we will repair or replace free of service charge for products deemed defective due to those causes.

This warranty is not valid for any damage or subsequent damage arising as a result of misuse, modification or as a result of failure to observe the procedures outlined in this manual.

Note:

The warranty service is valid in China only.

If you need warranty service overseas, please contact your dealer in the first instance, who is responsible for processing guarantee claims overseas. Due to high shipping cost, complicated custom clearance procedures to send back to China. Please understand SkyRC can't provide warranty service to overseas end user directly.

If you have any questions which are not mentioned in the manual, please feel free to send email to

3. info@skyrc.cn

This content is subject to change.

Latest version can be downloaded from www.skyrc.com

All specifications and figures are subject to change without notice. Printed in China 2017.05

7504-0907-02

FCC ID: REY-D100V2

RoHS

Skyrc D1000 V2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual