22332.8 - March/2014
INSTRUCTION MANUAL
FOOD PROCESSOR
MODELS
- ALÉM DESTAS MÁQUINAS, FABRICAMOS UMA LINHA COMPLETA DE EQUIPAMENTOS. CONSULTE SEU REVENDEDOR.
- ESTE PRODUTO CONTA COM ASSISTÊNCIA TÉCNICA, REPRESENTANTES E REVENDEDORES EM TODO TERRITÓRIO NACIONAL.
DEVIDO À CONSTANTE EVOLUÇÃO DOS NOSSOS PRODUTOS, AS INFORMAÇÕES AQUI CONTIDAS PODEM SER MODIFICADAS SEM AVISO PRÉVIO.
LINHA DIRETA
SKYMSEN
Ramais 20 11
2012
2013
E-mail: at@siemsen.com.br
METALÚRGICA SIEMSEN LTDA.
Rua Anita Garibaldi, nº 262 – Bairro: Sno Luiz – CEP: 88351-410
Brusque – Santa Catarina – Brasil
Fone: +55 47 3255 2000 – Fax: +55 47 3255 2020
www.siemsen.com.br - comercial@siemsen.com.br
METALÚRGICA SIEMSEN LTDA.
METALÚRGICA SIEMSEN LTDA.
01
SUMMARY
1 Main Precautions
2 Main Components
3 Technical Characteristics
4 Available Discs
5 Installation
6 Pre-Operation
7 Operation
7.1 How to place the discs
7.2 How to feed the Processor
8 Cleaning
9 Problems Analysis and Solution
10 How to sharpen the knife blades
11 General Warnings
12 Electrical Diagram
1
2
3
3
3
4
4
5
5
7
8
8
9
9
02
WARNING TO PROPRIETORS AND OPERATORS
The Food Processor has been designed to process foods with efficiency and safety .
However , as much well trained should be an operator, the possibility of a serious accident
exists . It is the proprietor responsibility to assure a safe and correct operation, following the
instructions of the present Manual and the local laws .
01 - MAIN PRECAUTIONS
The Food Processor may be a dangerous machine when incorrectly used. Cleaning and
maintenance shall be made only by skilled operators. Therefore to avoid accidents read
carefully all the following instructions :
TO BE USED only by skilled operators .
BEFORE cleaning or maintenance unplug the machine from electric power source .
NEVER use tools not belonging to the machine to help operation .
BEFORE to switch ON the machine check if the Disc No. 01 (Pic.03)and the Lid No. 02
(Pic.01)are duly held on their position .
NEVER remove the Lid before the machine is completely still .
NEVER put the hand inside the feeding throat , nor inside the processed food exit opening.
Keep hands away from any moving parts .
NEVER switch ON the machine with wet hands or clothes .
NEVER throw water or other liquids directly on the motor , electric switch , or any other
electrical component .
ALWAYS install the machine in a wide and clear working area , far from the reach of children
and visitors .
NEVER operate the machine without its warning labels and the Instruction Manual out of
reach .
NEVER let the machine alone during operation .
ALWAYS ground the machine in accordance with local rules .
STOP the machine immediately if unusual noises are heard, or when having the feeling that
some kind of accident might occur .
CONTACT your dealer, if any problem arises when installing or operating the machine .
09
12. ELECTRICAL DIAGRAM MODELS PA-7S and PA-7L
ON/OFF switch
Voltage Selector Switch
11 GENERAL WARNINGS
ALWAYS switch OFF the machine before maintenance or cleaning .
CLEAR enough space around the machine to avoid accidents .
KEEP FLOORS dry . Wet floors may cause to slip .
ALWAYS switch OFF the machine when electricity is cut out .
NEVER allow dirt or water get inside electrical or mechanical
components .
DO NOT change the original characteristics of the machine .
DO NOT remove safety and identification labels .
DO NOT wear loose fitting clothes while operating the unit.
DO NOT use bracelets or any other piece of jewerly.
Have your hair ALWAYS shortened and held up (use hair fishnets if
necessary) in a way it cannot reach any part of the machine. Roll up any loose
sleeves.
SKYMSEN IS NOT responsible for ANY harm or injury caused by the
negligent or inappropriate use of this equipment by any operator.
This equipment MUST BE operated only by persons whose age equals
or exceeds 18 years old, in a safe and sound state of mind, free from the
influence of any kind of drugs and alcohol, that received proper training
and instructions regarding the correct operation of this machine, that are
wearing correct and authorized safety clothes.
All and any kind of modifications carried on and applied to this machine
IMMEDIATELY NULLIFIES ANY KIND OF WARRANTY and may result in harm
and injuries to the individuals operating this machine and to individuals that are
03
1 Large stump
2 - Lid with feeding throats
3 Cabinet
4 ON/OFF switch
5 - Voltage Selector Switch
6 Small Stump
7 Handle
8 Warning Label
9 Collecting Bowl
10 Lid fastener
01 -Lid with feeding throats
1 - Disc
2 - Central shaft
Picture - 01
Picture - 03
01
02
Picture - 02
01
05
04
03
10
02
01
06
07
08
09
02 MAIN COMPONENTS
08
09 PROBLEMS ANALYSIS AND SOLUTIONS
The Processors has been designed to need a minimum maintenance . However some
problems may arise due to normal wear during the machine life .
If some problem arises with your Food Processor , check Table 03 , where some possible
solutions are recommended.
TABLE 03
PROBLEMS CAUSES SOLUTIONS
Irregular cutting Bunt blades Sharpen blades as per
item No.10 ( How to
sharpen blades )
The disc stops Electric power Check if the plug is
during operation shortage into its socket
Internal or external
electric wiring problem Call the dealer
Smoke or burnt smell Electric motor or other
electric parts problem Call the dealer
The machine switches ON Motor capacitor failed Call the dealer
but the disc delays to start
moving
Unusual noises Disc not correctly fitted. Remove the lid and
Bearing Failure. replace the Disc.
Lid not fastened . Call the dealer.
Tight the handles
Lid leakage Handles No. 7 (Pic.01) Tight the handles
are loose . No.07(Pic.01)
To much dirt between Clean the machine
the Disc Housing and following item
the Lid No.02(Pic.01) No. 8 .
10 HOW TO SHARPEN THE KNIFE BLADES
The blades may be removed , therefore may be easy sharpened , however special
attention must be given to keep the right original cutting angle .The blades must be
sharpened using a sharpening stone or a thin sandpaper .
Use a screw driver to remove the blades .
04
(*) Observation : the frequency will be the frequency indicated on the motor
04 AVAILABLE DISCS
TABLE 02 gives the food processor available discs
Table - 01
Characteristics Unit PA-7S PA-7L
Average Production [kg/h] 250 250
Voltage [V] 110/220 110/220
Frequency [Hz] 50 or 60 (*) 50 or 60 (*)
Power Rating [CV] 0,5 0,5
Consumption [kW/h] 0,4 0,4
Height [mm] 595 595
width [mm] 380 380
length [mm] 445 445
Net weight [kg] 22 22
Gross weight [kg] 24 24
05 INSTALLATION
The Food Processor shall be installed on a steady and flat surface . The installation shall
be made only by qualified or experienced personnel . The surface should be 850 mm
high above floor level.
3. Technical Characteristics
07
08 CLEANING
All the removable parts shall be washed with neutral soap and hot water .
Follow the below steps to remove these parts :
-Switch the machine OFF , and then unplug it from electric network .
- Remove the Stumps No.01 and No.06 (Pic.01) and the Bowl No.09 (Pic.01).
- Lose the handles No.07 (Pic.01) .
- To remove the Lid and proceed as shown on Picture 02 .
- Do be careful with the Disc knives . Grab the Disc and turn it counterclockwise , and then lift
it .
- Wash the removable parts with hot water and neutral soap . Using a wet cloth clean the
Cabinet and the Disc housing . Then dry them .
IMPORTANT
BEFORE to clean the machine unplug it from the electric network . Always be
sure that the Disc is completely still.
IMPORTANT
Do be careful with the knives , when washing the Discs .
WRONG
WAY
CORRECT
WAY
IMPORTANT
Never use to much force to push the aliments down with the Stump. To obtain a
better performance use refrigerated aliments
DESIGNATION MODEL
SLICER DISC - 1,5 mm SLICER DISC - 3 mm SHREDDER DISC - 3 mm SHREDDER DISC - 5 mm SHREDDER DISC - 8 mm GRATER DISC -
DESIGNATION MODEL
- -
DISCS SUPPLIED WITH
THE EQUIPMENT
OPTIONAL DISCS
(sold separately)
Table 02
05
06 PRE-OPERATION
IMPORTANT
Before to place the lid on top of the cabinet check and be sure that the disc is correctly fitted ,
in order to avoid damages to the machine .
The machine shall be steady , no movement is supposed to be allowed on the supporting
surface .Wash all the parts in contact with the food with neutral soap and hot water, then dry
them .
The equipment is now ready to be used.
IMPORTANT
Switch OFF the machine when it is desired to change the Disc . Be sure the
machine is completely still before to remove the lid .
Be sure that the Lid No.02 (pic.01) is correctly fastened . To Switch ON the machine use the
red ON/OFF button Switch No.04 (Pic.01) on the side of the Cabinet .
07 OPERATION
OBSERVATION
FOR YOUR OWN SAFETY READ ALL THE SAFETY LABELS FIXED
ON THE MACHINE .
06
-With the machine switched OFF and the disc still , remove the stumps
No.01 and No.06 (Pic.01) , and remove the Lid No.02 (Pic.01) . To remove the lid it is
necessary to lose the handles No.07 (Pic.01) and turn the Lid No.02 (Pic.01)
counterclockwise about ¼ of a turn .
-Be careful with the Disc. Grab the desired Disc and fit it on the Central Shaft No.02 (Pic.03)
turning it counterclockwise to have it perfectly fastened .
-Fit the Lid No.02 (Pic.01) and be sure it is perfectly fastened, tightening the handles No.07
(Pic.01) .
7.1 How to place the discs
7.2 How to feed the Processor
IMPORTANT
NEVER use tools not belonging to the machine to help operation, and
particularly do not use the hands . Use always the Stumps No.01 and No.06
(Pic.01) to feed the machine.
The Food Processors PA-7S and PA-7L are machines operating at high
speed, therefore they shall be fed fast .
To feed the machines remove the Stump No.01 or No. 06 (Pic.01) place the product to be
processed inside the correct throat and push it down , always use the proper Stump . To
process small vegetables , such as , carrots , cucumbers or similar use the small throat with
the small stump .
Use the Stumps as the
below Picture
CORRECT way WRONG way
Never use the small stump inside the
large throat . Irreparable damages
will occur .
Check the voltage . The motor voltage shall be the same as the voltage of the electric
network . If the machine voltage is not the same as the electric network voltage , use
the Voltage Selector Switch No.05 (Pic.01) placed under the machine bottom. Contact
your dealer in case any problem or question arises during installation.
This equipment is provided with a two or three pin electric cable. All pins must be
connected before the machine is turned on
Loading...