Model
28595.1 - Março/2011
USER MANUAL
PLANETARY MIXER
BPS-30CE
®
- ALÉM DESTAS MÁQUINAS, FABRICAMOS UMA LINHA COMPLETA DE EQUIPAMENTOS. CONSULTE SEU REVENDEDOR.
- ESTE PRODUTO CONTA COM ASSISTÊNCIA TÉCNICA, REPRESENTANTES E REVENDEDORES EM TODO TERRITÓRIO NACIONAL.
DEVIDO À CONSTANTE EVOLUÇÃO DOS NOSSOS PRODUTOS, AS INFORMAÇÕES AQUI CONTIDAS PODEM SER MODIFICADAS SEM AVISO PRÉVIO.
LI NHA D IRE TA
SKYMSEN
Ra mai s 201 1
20 12
20 13
E-mail: at@siemsen.com.br
METALRGICA SIEMSEN LTDA.
Rua Anita Garibaldi, nº 262 – Bairro: Sno Luiz – CEP: 88351-410
Brusque – Santa Catarina – Brasil
Fone: +55 47 3255 2000 – Fax: +55 47 3255 2020
www.siemsen.com.br - comercial@siemsen.com.br
METALÚRGICA SIEMSEN LTDA.
METALÚRGICA SIEMSEN LTDA.
01
01
01
02
02
02
02
06
06
07
08
09
09
08
09
10
09
02
02
03
03
03
03
1.Introduction
1.1.Safety
1.2.Main Spare Parts
1.3.Technical Data
2.Instalation and Pre - Installation
2.1.Installation
2.2.Pre-Installation
3.Operation
3.1.Starting
3.2.Feeding Procedures
3.3.Agitators Assembling
3.4.Bowl Assembling
3.5.Cleaning
4.General Safety Practices
4.1.Basic Operation Procedures
4.2.Warnings before starting the machine.
4.3.Routine Inspections
4.4.Operation
4.5.After work
4.6.Maintenance
5.Problems Analysis and Resolution
5.1.Problems, Causes and Solutions
5.2.Eletric Diagram
SUMMARY
01
1. Introduction:
1.1 Safety
When not properly used the Planetary Mixer is potentially dangerous machine.
Maintenance, cleaning or any other operation shall be made by trained people. Plug has to
be off the outlet during any of these operations.
Remove plug from outlet when you wish to remove any removable part during cleaning,
maintenance or any other operation.
Never make use of any tool or instrument that is not originally part of the machine for any
operation. Be sure that removable parts are properly attached to its correct position.
Never throw water directly on the machine.
Keep hands off turning parts.
DO NOT operate the machine wearing wet clothes or wet shoes.
Be sure the machine is grounded.
Operator has to tie his/her hair up before starting the operation.
Keep this manual and have it handy for use any time.
1.2 Main Components:
All components that are part of the machine were designed and made to its proper function
according to pattern tests and experience of Siemsen. The new concept of the steel plate
used in this machine makes it a sanitary safe and clean machine.
02
1.3 Technical Features
2.1 Installation
Planetary Mixers Models BPS-30CE, shall be installed on flat and firm surface.
2. Instalation and Pre Operation
(*) Height with closed cage (+415mm with open cage).
2.2 Pre-Operation
Check if the Planetary Mixer is stable on the surface. Before using the machine, remove and
wash all removable parts. For your safety, read carefully iten "3.5 Cleaning" in this Manual.
3.1 Starting the machine
3. Operation
To start the machine first turn Timer (Nº 06 Fig. 01) clockwise to select intended time of
use and then turn Speed Control knob (Nº 02 Fig. 01) clockwise to select speed as
indicated in the food load table, located on the side of the cabinet (Nº 03 Fig. 01),
intended for use with each tool.
Obs.: The machine will start only when the safety cage (Nº 01 Fig. 01) is down.
U.M.
[litros]
[V]
[Hz]
[HP]
[kW/h]
[mm]
[mm]
[mm]
[l]
[kg]
BPS-30CE
30
110 or 220
50 or 60
1,5
1,1
1380 (*)
520
970
150
175
Characteristics
Bowl capacity (wiithout agitators)
Voltage
Frequency
Rating
Consumption
Height
Width
Depth
Net weight
Gross weight
Load Chart
Model
Maximum LoadMinimum Load
BPS-30CE
6 liters or 40 eggs2 liters or 30 eggs
5kg flour1kg flour
03
3.2 Feeding Procedures
Choose the agitator to be used: Whip (No.1 Pic 03), Racket (No. 01 Pic 02) or spiral (No. 01
Pic 04), put the ingredients into the Bowl (No.05 Pic 01), move down the Safety Cage (No.01
Pic 01), turn the timer (No.02 Pic 05), select the time and select the speed (No.01 Pic 05).
The ON/OFF command is controled by the Timer. Therefore Speed Control Knob will
always be positioned in one of the four speeds. To turn Mixer ON just select desired speed
and then set the Timer with desired processing time. Once processing time is over Mixer will
be turned OFF automatically.
3.3 Agitators Assembling
All agitators (Pic 01 / 02 and 03) are assembled in the same way.
*Lift the Agitator Shaft Holder (No.01 Pic 07), placed in the shaft (No.02 Pic 07).
*Place the hole, located in the Agitator, in the Pin (No.03 Pic 07).
*Move the Agitator Shaft Holder down(No.01 Pic 07).
3.4 Bowl Assembling
* Place the Bowl on the bowl support (Nº 04 Pic.01).
* Place the guide (Nº01 Pic.08) located on the bowl into the spot (Nº02 Pic.08) located on the
bowl support and after that place the holes (Nº03 Pic. 06) in the bowl support pins (Nº01
Pic.06).
* Lock the bowl in the right position, turning the lever (Nº 02 Pic.06) untill to fit in the bowl
support pins (Nº01 Pic.06).
All removable parts must be removed and cleaned. Clean with water and Neutral Soap.
3.5 Cleaning
Important
Never do cleaning with the machine plugged in, always unplug the machine before
cleaning.
Important
Never throw water directly on the machine.
Pic-01
03
01
05
02
06
01 - Bowl
02 - Speed Control Knob
03 - Cabinet
04 - Safety Cage
05 - Bowl Support
06 - Timer
04
®
10
Strange Noises
Machine turns on but takes
too long to turn the agitator
(No.1 Pic 07)
Machine stops during
operation
Defective bearings
Defective Start capacitor
Belts not fastened enough
Call technical assistance
Call technical assistance
Call technical assistance
No power source
Be lts no t fast ene d
enough
Bad contact in the Timer
or Speed Control Knob.
Check if plug is connected
to the power outlet
C a l l t e c h n i c a l
assistance
C a l l t e c h n i c a l
assistance
5.2 Electric Diagram Mod. BPS-30CE
Problems Causes Solutions
3.3.2 Cautions with Stainless Steel:
The Stainless Steel may present rust signs, which ARE ALWAYS CAUSED
BY EXTERNAL AGENTS, especially when the cleaning or sanitization is not
constant and appropriate.
The Stainless Steel resistance towards corrosion is mainly due to the
presence of chrome, which in contact with oxygen allows the formation of a very
thin protective coat. This protective coat is formed through the whole surface of the
steel, blocking the action of external corrosive agents.
When the protective coat is broken, the corrosion process begins, being
possible to avoid it by means of constant and adequate cleaning.
Cleaning must always be done immediately after using the equipment. For
such end, use water, neutral soap or detergent, and clean the equipment with a soft
cloth or a nylon sponge. Then rinse it with plain running water, and dry immediately
with a soft cloth, this way avoiding humidity on surfaces and especially on gaps.
The rinsing and drying processes are extremely important to prevent stains
and corrosion from arising.
IMPORTANT
Acid solutions, salty solutions, disinfectants and some sterilizing solutions
(hypochlorites, tetravalent ammonia salts, iodine compounds, nitric acid
and others), must be AVOIDED, once it cannot remain for long in contact
with the stainless steel:
These substances attack the stainless steel due to the CHLORINE on its
composition, causing corrosion spots (pitting).
Even detergents used in domestic cleaning must not remain in contact with
the stainless steel longer than the necessary, being mandatory to remove it with plain
water and then dry the surface completely.
Use of abrasives:
Sponges or steel wool and carbon steel brushes, besides scratching the
surface and compromising the stainless steel protection, leave particles that rust and
react contaminating the stainless steel. That is why such products must not be used
for cleaning and sanitization. Scrapings made with sharp instruments or similar must
also be avoided.
Main substances that cause stainless steel corrosion:
Dust, grease, acid solutions such as vinegar, fruit juices, etc., saltern
solutions (brine), blood, detergents (except for the neutral ones), common steel
particles, residue of sponges or common steel wool, and also other abrasives.
04
09
4.5After Finishing The Work
4.5.1Precautions
Always TURN THE MACHINE OFF by removing the plug from the socket before
cleaning the machine. Never clean the machine unless it has come to a complete stop.
Put all components back to their functional positions before turning it ON again. Check
level of oil. DO NOT place your fingers in between belts and pulleys nor chains and
gears.
4.6 Maintenance
4.6.1Danger
Any maintenance with the machine in working situation is dangerous. TURN IT OFF BY
PULLING THE PLUG OFF THE SOCKET DURING MAINTENANCE.
4.6.2Advice
Electrical or mechanical maintenance must be done by qualified personal for such
operation.
Person in charge has to be sure that the machine is under TOTAL SAFETY conditions
when working.
5 Analysis and Problem Solving
5.1 Problem, causes and solutions
The Planetary Mixers were designed to operate with the need of minimum maintenance
but the natural wearing caused by longer use of the equipment may occasionally cause
some malfunctions.
If any such problem occurs with your mixer refer to Table 02 in which the most common
situations are listed with recommended solutions.
Table- 02
Problems Causes Solutions
Burning odor and /or
smoke
Motor or other electric parts
problem
Call technical assistance
05
Pic-02 Pic-03 Pic-04
Pic-06Pic-05
Pic-07
Pic-08
01
01
01
02
03
01
01
02
03
02
01
01
02
08
4.2.3 Precautions
The electric cable has to be compatible with the power required by the machine. Cables
touching the floor or close to the machine need to be protected against short circuits.
Oil reservoir has to be full up to the required level as indicated. Check level and add oil if
necessary.
4.3 Routine Inspection
4.3.1 Advice
When checking the tension of the belts or chains, DO NOT introduce your fingers between
the belts and the pulleys and nor between the chain and the gears.
4.3.2 Precautions
Check if motors and sliding or turning parts of the machine produce abnormal noises.
Check the tension of the belts and chains and replace the set when belt or chain show signs
of being worn out.
When checking tensions of belts or chain DO NOT introduce your fingers between belts and
pulleys, nor between the chains and gears.
Check protections and safety devices to make sure they are working properly.
4.4 Operation
4.4.1 Advice
Be sure your hair is not loose in order to avoid getting caught by turning parts which could
lead to a serious accident. Tie your hair well up and/or cover your head with a scarf.
The operation performed by not trained or skilled personnel shall be forbidden.
Never touch turning parts with your hands or in any other way.
NEVER operate machine without all original safety devices under perfect conditions.
06
The following safety instructions are addressed to both the operator of the machine as well
as the person in charge of maintenance. The machine has to be delivered only in perfect
conditions of use by the Distributor to the user. The user shall operate the machine only after
being well acquainted with the safety procedures described in the present manual. READ
THIS MANUAL WITH ATTENTION.
4.1 Basic Operation Practices
4.1.1 Dangerous parts
Some parts of the electric devices are connected to high voltage points. These parts when
touched may cause severe electrical shocks or even be fatal.
Never touch commands such as buttons, switches and knobs with wet hands, wet clothes
and/or shoes. By not following these instructions operator could be exposed to severe
electrical shocks or even to a fatal situation.
4.1.2 Warnings
The operator has to be well familiar with the position of ON/OFF Switch to make sure the
Switch is easy to be reached when necessary. Before any kind of maintenance, physically
remove plug from the socket.
Provide space for a comfortable operation thus avoiding accidents.
Water or oil spilled on the floor will turn it slippery and dangerous. Make sure the floor is
clean and dry.
Before giving any manual command (switch, buttons, turn keys or lever) be sure the
command is the correct one. Check this manual for further details if necessary.
Never use a manual command (switch, buttons, lever) unadvisedly.
If any work is to be made by two or more persons, coordination signs will have to be given for
each operation step. Every step of the operation shall be taken only if a sign has been made
and responded.
4. General Safety Practices
IMPORTANT
If any item from the GENERAL SAFETY NOTIONS section is not
applicable to your product, please disregard it.
07
4.1.3 Advices
In case of power shortage, immediately turn the machine OFF.
Use recommended or equivalent lubricants, oils or greases.
Avoid mechanical shocks as they may cause failures or malfunction.
Avoid penetration of water, dirt or dust into mechanical or electrical components of the
machine.
DO NOT modify original characteristics of the machine.
DO NOT remove, tear off or maculate any labels stuck on the machine. If any label has
been removed or is no longer legible, contact your nearest dealer for replacement.
READ CAREFULLY AND WITH ATTENTION THE SAFETY OR OPERATION
INSTRUCTIONS LABELS DISPLAYED ON THE MACHINE, AS WELL AS THE
INSTRUCTION MANUAL AND THE TECHNICAL CHARACTERISTICS WRITTEN
INSIDE.
4.2 Safety Procedures and Notes Before Switching Machine ON
IMPORTANT
Carefully read ALL INSTRUCTIONS of this manual before turning the machine ON.
Be sure to be familiar with the instructions and that you have well understood all
information contained in this manual. If you have any question contact your
supervisor or your nearest Dealer.
4.2.1 Danger
An electric cable or electric wire with damaged jacket or bad insulation could cause
electrical shocks as well as electrical leak. Before use, check conditions of all wires and
cables.
4.2.2 Advices
Be sure ALL INSTRUCTIONS in this manual have been thoroughly understood. Every
function and operational procedure has to be very clear to the operator. Contact your
nearest Dealer for further questions.
Any manual command (switch, button or lever) shall be given only after being sure it is the
correct one.
Loading...