SKYMAX
USER MANUAL
DIGITAL
SATELLITE & TERRESTRIAL
RECEIVER
SKYMAX SX 771 ST COMBO
SKYMAX - POLAND Ltd. - 2004
www.skymax.pl
Safety:
1.Allow clear space around the DSR for sufficient ventilation.
2.Do not cover the DSR or place it on a unit that emits heat.
3.Use a soft cloth and mild solution of washing liquid to clean the casing.
4.Do not connect or connect or modify cables when the DSR is plugged in.
5.Do not remove the cover.
6.Do not allow the unit to be exposed to extreme heat, cold or humid conditions.
7.Never allow liquids, spray or other materials to come into contact with the inside the model.
Main Features:
1.Two tuners: Satellite and Terrestrial.
2.Fully MPEG2, DVB-S and DVB-T compliant system
3.Digital Audio with AC-3 support by SPDIF.
4.PIG (Picture In Graphic) support DiSEqC 1.2 positioner for multi-satellites.
5.C/Ku band control for each antenna.
6.User Friendly and easy-to-use menu system.
7.Various channel editing functions (favorite, moving, locking, renaming, deleting and sorting).
8.User programmable various satellite & transponder information.
9.Automatic search for newly added transponder.
10.Stores up to 4000 channels.
11.Easy and fast software upgrade through RS-232 port.
12.Plug-and-play data transfer system (DSR to DSR).
13.Timer function, automatically turns On/Off by setting function (daily, weekly, monthly, one
time).
14.Automatic reserved channel moving system.
15.Electronic Program Guide (EPG).
16.Antena positioning help feature.
17.Multi video output – CVBS,RGB.
18.Provides various switch types, LNB types and PAL/NTSC monitor types.
19.SCPC/MCPC receivable from C/Ku band satellite .
20. Multi LNB controlled by DiSEqC 1.2 and 22kHz, 0/12 volt switching.
21.Automatic PAL/NTSC conversion.
22.Automatic last channel scanning.
23.OSD Teletext (DVB ETS 300 706) and subtitle function support.
24.VBI Teletext support.
25.Full function by remote control; volume control.
26.PLL RF Modulator (UHF 21~69 CH.).
2
3
1. Front Panel
1. MENU: Shows the main menu and command box on the screen.
2. POWER: Turns on and off the power of the receiver.
3. CH: When watching, changing to the previous and next channel, or moves to the next higher
or lower item in the menu.
4. VOL: When watching a channel, adjust the volume or move to the left or right item in the
menu.
5. 4 digital LED display: Shows program information at startup displays software and menu.
6. OK: Confirm the selected item in the menu.
2. Rear Panel
1. ANT IN: Connects the terrestrial antenna cable.
2. ANT OUT: Use it to connect TV set or other STB.
3. SAT ANT IN: Connects the satellite antenna cable.
4. SAT ANT OUT: Use it to connect to other STB.
5. RS-232: Upgrades the STB Program & Software.
6. VCR: Connects your VCR via a SCART cable to this receiver.
7. TV: Connects your TV set via a SCART cable to this receiver.
8. 0/12V: Chooses the LNB on the antenna.
9. S/P DIF: Output for connection to a digital amplifier.
10. VIDEO OUT: Video output.
11. AUDIO OUT R/L: Audio output.
12. TV ANT IN: Connects to the TV antenna.
13. TO TV: Connects to the TV set antenna input.
14. ~100-240V (Auto-selectable), 50/60 Hz. Make sure to check the specification.
3. Main Menu
Once you have installed and connected the cables of the DSR the menu will be displayed.
This menu consists of 6 menu options as shown below.
1. User Installation
2. System Settings
3. Channel Manager
4. User Preference
5. Receiver Information
6. Game
During the installation the OK key confirms a selection
and LEFT/RIGHT key shows the Drop Down List box.
You can use the VOL LEFT/RIGHT keys to move from
4
main menu to sub menu and move from left side to right side or vice versa. To escape the menu
system at anytime, press EXIT key on the remote control unit.
4. User Installation
This menu consists:
1. Satellite Setup
2. Terrestrial Setup
Satellite Setup is for Digital Satellite TV (DVB-S) and
Terrestrial Setup is for Digital Terrestrial TV (DVB-T).
4.1. Satellite Setup
This menu consists TP Search, Position, DiSEqC,
LNB Type, LNB Freq.1, LNB Freq. 2, 0/12 Volt,
22kHz, C/Ku Band Control.
a. TP Search: Select Search item and press OK key, the display as below:
In this menu, you can set Frequency and Symbol
Rate and Polarization, select search type, then press
OK button to search. In this menu, you can also can
Set PID (Blue color key), Delete TP (Red color key),
Search Options (Gray color key), New TP (Green
color key).
b. Set PID
If you want to set PID (Packet Identifier) manually,
select TP in the “Channel Search Page” and press
SET PID key (Blue color key) on the RCU (remote
control unit) to display the command box. Then select
SET PID command and press OK. The set PID menu
will be displayed. Enter the correct value and select
OK.
5
6
7
4.8. Terrestrial Setup
This menu consists of 8 parameters of DVB-T multiplex as shown below.
- Index - channel number,
- Frequency KHZ – channel frequency,
- Mode – number of carriers 2048 or 8192,
- Guard Interval – can have four different values:
1/4, 1/8, 1/16 and 1/32,
- FEC Rate – Forward Error Correction – value:
1/2 ,2/3 , 3/4 , 4/5, 5/6, 6/7, 7/8, 8/9, All, none,
- Bandwidth – select 6, 7 or 8 MHz,
- Modulation – type of digital modulation: select
QPSK, 16QAM, 64QAM and All(auto),
- Select Band – VHF low, VHF high, UHF, All(auto).
You can search channels of the DVB-T multiplexes like in satellite setup menu: Auto Search
(yellow key), Set PID (blue key), Search current TP (red key), Search option (gray key).
8
9
10
11
12
13
14
Loading...