SkyLink WD-103 User Manual

Door/Window Sensor Model WD-103

1. INTRODUCTION

The Door / Window Sensor is designed to monitor any door or window
within your house. It works in conjunction with MA Series Control Panel.
When the monitored window or door is opened, the control panel will
either alert you or alarm will be triggered.

In this package, you should find a sensor, a magnet, 3V lithium battery
and other mounting accessories.

Magnet

Please follow the instructions below to set up the door / window sensor.

2. LEARN SENSOR TO MA SERIES CONTROL PANEL

In order for the sensor to communicate with the control panel properly,
the sensor must be programmed to the control panel. Follow the brief
instructions below or refer to the detail instructions from the MA Series
User’s Instructions to program the sensor to the control panel. Before
proceeding, please remove the battery isolator from the sensor, and
placing the magnet beside the transmitter (where the red marking is)

Step 1:
Press and hold the Learn Button on the Control Panel for 3 seconds.
Control Panel beeps once and you may release the Learn Button.

Sensor

2 pcs 3.5 x 18 screws
2 pcs 3.5 x 12 screws

INPUT DC 12VINPUT DC 12V

MUTEMUTE

LEARNLEARN

Press 3 sec.

ALERTALERT

CHIMECHIME

OFFOFF

3V Lithium
battery

Long Beep

Mounting plate

2. LEARN SENSOR TO MA SERIES CONTROL PANEL (CONT)

Test Sensor

After learning the sensor to the control panel, you may test the com­munication by placing the magnet beside the transmitter (where the red
marking is) and remove the magnet from the transmitter.

When the magnetic contact is closed, the
receiver will not beep.

When the magnetic contact is broken (open),
the receiver will beep and a LED will flash.

1) Zone LED of this sensor will flash

2) Beeping according to the zone number [Alert Notification Switch is set
to "Alert"]. 1 beep for zone 1, 2 beeps for zone 2 etc, until the sensor
is closed.

Note: If the Alert Notification Switch is set to "Chime", Control Panel will
chime once for every signal activation. If the Alert Notification Switch is
set to "OFF", no audio alert will sound.

3. INSTALLATION

The transmitters should be mounted on the door frame or window frame
by double sided tape. The magnet should be mounted on the door or
window by either double sided tape or screws. Make sure the magnet is
aligned with the red marking on the transmitter. If the surface of the frame
is flat enough, double-sided foam tape is sufficient, otherwise, it is
recommended to screw the mounting plate to the frame, then apply
double sided tape. After mounting the sensor, if the Skylink logo is
inverted, remove the front cover and rotate it so the Skylink logo is in the
upright position.

Step 2:
Press the zone button (1, 2, 3, or 4) once, for which you want to program
the sensor to. The selected Zone LED will flash.

Press the zone button

Zone LED flashing

Step 3:
Activate the Door Window Sensor by separating the magnet from the
sensor unit.

Magnet

Sensor

Separate the
magnet from
the sensor.

Control Panel long beep
Zone LED flashing OFF

Step 4:
You will hear a long beep and the zone LED stops flashing. The sensor
is now programmed to the Control Panel.

Note:

You may program up to 4 sensors to one zone.

Zone 4 is an alert zone, sensors in this zone is for alert purpose ONLY
and will not trigger the alarm.

"Red Marking"
on the side

Magnet

Mounting plate
and screws (optional)

Sensor

Double-sided
foam tape

"Red Marking"
on the side

Sensor

Sensor

Magnet

Testing:

After mounting the sensor, test the sensor by opening and closing the
door or window. The Control Panel should respond in the same way as
described above, "Test Sensor".

Note:

- Try to mount the sensors as far away from the floor as possible to
avoid damaging them. Mounting the sensors at a higher position will
also result in better operating range.

- Do not mount the sensor to the exterior of the door / window, always
mount the sensor to the interior side of the door / window to avoid being
damaged or stolen by non-intended users.

4. OPERATION

Door/Window Sensor is used to monitor doors or windows that open and
close. When these doors / windows are open or closed, the sensors will
transmit a signal to the control panel to notify the user.

Refer to the MA Series User’s Instructions for detail information regarding
the operation of this door / window sensor with the control panel.

5. SENSOR FAILURE / LOW BATTERY INDICATION

The control panel constantly monitors its sensors, if the control panel fails
to communicate with any sensors, it will begin rapidly flashing the zone
LED indicator.

When sensor failure occurs, try the following:

1. Check if the sensor is located at where it should be, and whether there
is any physical damage to the sensor.

2. If the failed sensor is not physically damaged, try to activate the sensor
and see if the control panel reacts to such activation.

3. If not, try to remove the sensor from its location, and bring it closer to
control panel and activate the sensor. It is possible that the sensor is
installed too far from the control panel and it cannot establish a steady
communication with the control panel. If this is the case, please install
the sensor closer to the control panel.

4. Replace the battery of the sensor in that zone if the Control Panel does
not respond when the sensor is activated within short range.

If you have multiple sensors in a zone, you may test the function of each
sensor to identify which sensor is having problem.

6. OTHER MA SERIES ACCESSORIES

The MA Series control panel can work with different accessories include:
Motion Sensor, Keychain Remote, Water Sensor, External Keypad,
Audio Alarm, Emergency Dialer, etc. Please visit www.skylinkhome.com
or contact us at [e-mail] for more information of how
to fully utilize your Wireless Alarm System - MA Series.

7. CE

Declaration of Conformity

This equipment complies with the requirements relating to electromagnetic
compatibility, EN 301489-3:2002, EN300220-2:2007, EN60950-1:2006,
EN50371:2002. This equipment conforms to the essential requirement of the
Directive (1999/5/EC) of the European Parliament and of the Council.

8. WARRANTY

If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.

9. CUSTOMER SERVICE

If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :

1. visit our FAQ section at www.skylinkhome.com, or

2. email us at [e-mail]

CUSTOMER SERVICE

Rm 1303, Block B, Veristrong Industrial Centre,
36 Aupuiwan Street, Fotan, N.T. Hong Kong.
Email:[e-mail]
http://www.skylinkhome.com

P/N. 101Z683
©2009 SKYLINK GROUP

Door / Window Sensor

WD-103