SkyLink UR-100 User Manual

PROGRAMMING THE RECEIVER

The Universal receiver works with Skylink remote transmitters
model #66, #66C, #36, #36C, #68, #68C, #68B, #68G, #68R,
#88, #88C, #88P. Use a paper clip to set the receiver DIP
switches to match your Skylink transmitter. Each switch of the
receiver has 2 positions (“ON” or “OFF”).

DIP
SWITCHES

WARNING: Unplug the

receiver before chang­ing code setting.

Refer to the chart below. If any of the DIP switches in the Universal Receiver
are set to “ON” position, set the switches in the Skylink transmitter to the “+”
position. If DIP switches on the Universal Receiver are set to “OFF” position,
set the switches in the Skylink transmitter to the “0” or central or blank position.

DIP switch setting to match with Skylink Universal Receiver and Skylink Transmitter

UNIVERSAL RECEIVER #UR100 SKYLINK TRANSMITTER
DIP SWITCH POSITION SETTING DIP SWITCH POSITION SETTING
1 ON / OFF 1 + OR 0
2 ON / OFF 2 + OR 0
3 ON / OFF 3 + OR 0
4 ON / OFF 4 + OR 0
5 ON / OFF 5 + OR 0
6 ON / OFF 6 + OR 0
7 ON / OFF 7 + OR 0
8 ON / OFF 8 + OR 0
9 ON / OFF 9 + OR 0

1. Disconnect the power from
your existing garage door
opener to avoid triggering
the door accidentally dur­ing installation.

2. Open your existing wall
mounted garage door
opener button.

3. Connect the wires to the
terminals and tighten as
shown. If your opener has
more than two terminals,
attach the wire to the same
two terminals that the wire

INSTALLATION

from the garage door
opener is connected to.

DO NOT REMOVE ANY
WIRES.

Replace button casing.

4. Plug in the wires to the
receiver as shown. Then,
plug in the receiver to an
electrical outlet.

5. Re-connect the power to
your garage door operator.

6. P ress the wall button to
test and check wiring for

proper operation.

ANTENNA

Existing wall
mounted button

RECEIVER

1. Locate frequency switch
on the top of the trans­mitter and set to position
A. (See diagram A)

Diagram A

1. Locate frequency switch
on the top of the trans­mitter and set to position
A. (See diagram G)

Diagram G

PROGRAMMING THE SKYLINK MODEL #66, 66C

2. T o program the model
#66, #66C, open the
case with a coin. (See
diagram B)

Diagram B

3. Use a pen or paper clip
to set the corresponding
DIP switches numbered
1 through 9 so that the
switches on the trans­mitter match those on
the receiver. Each switch
of the transmitter has 3
positions (“ + ”, “ 0 ”,
“ - ”). T o operate with
Skylink #UR-100, only
set the switches to “ + ”
or “ 0 ”. Do not use “ - ”
position.Leave the re­maining DIP switches in

4. Test the transmitter with

PROGRAMMING THE SKYLINK MODEL #38, #38C

2. T o program the model
#38, #38C, open the
case with a coin. (See
diagram H)

Diagram H

3. The transmitter contains 8
brand jumpers (see dia­gram I) and 12 code con­nectors. (See diagram J).

Code connector Location

12345678

Brand Jumper

the transmitter at “0” or
the center position. (See
diagram C)

DIP Switch Location

Diagram C

the Universal receiver.

4. The brand jumper has 8 rows
of posts, each row has 2 posts.
(see diagram I). The connec­tor, (see diagram K), must be
placed to the position ‘ 7 ’.

5. The code connector (see dia­gram J) has 12 rows of posts,
each rows has 3 posts. Each

1. Locate frequency switch
on the top of the trans­mitter to position A.
(See diagram D)

Diagram D

Diagram I

PROGRAMMING THE SKYLINK MODEL #36, 36C

2. T o program the model
#36, #36C, open the
case with a coin. (See
diagram E)

Diagram E

row contains one connec­tor (see diagram K) for a
total of 12 connectors.

Diagram J

Diagram K

3. Use a pen or paper clip
to set the corresponding
DIP switches numbered
1 through 9 so that the
switches on the trans­mitter match those on
the receiver. Each switch
of the transmitter has 3
positions (“ + ”, “ 0 ”,
“ - ”). T o operate with
Skylink #UR-100, only
set the switches to “ + ”
or “ 0 ”. Do not use “ - ”
position.Leave the re­maining DIP switches in

If the connector is placed on the top and middle posts, that
row is set on “ + ” or “ON”. If the connector is removed com­pletely, (not placed on any posts), it is set to “ 0 ” or the neu­tral position. (see diagram L for examples of how to set a row
to the three different positions).

T o operate with Skylink #UR100,
only set to “ + ”or “ 0 ” position.
Do not place the connector to
the middle & bottom posts “ - ”
position.

When removing a connector to
set a row to the neutral position,
save the connector in case you
change the code at a later date.

the transmitter at “0” or
the center position. (See
diagram F)

DIP Switch Location

Diagram F

4. T est the transmitter with
the Universal receiver.

‘+’ OR ‘ON’

‘0’ = BLANK

Diagram L

PROGRAMMING THE SKYLINK MODEL #38, #38C

6. To move the connectors, slide an
opened paper clip into the side of
a connector and lift. (see diagram
M) When repositioning connec­tors, place a connector on the two
chosen posts, then push down on
the connector with your finger.

Paper

Clip

Diagram M

7. Set the connectors num­bered 1 through 9 so that
the switches on the trans­mitter match those on the
receiver. Leave the re­maining posts at “ 0 ”,or
the blank position (remove
the connectors). See the
diagram J for details.

8. T est the transmitter with
the Universal receiver.

PROGRAMMING THE SKYLINK MODEL #68, #68C, #68B, #68G, #68R

1. Locate frequency switch
on the top of the trans­mitter and set to position
A. (See diagram N)

Diagram N

2. T o program the model
#68, #68C, #68B, #68G,
#68R, open the case
with a coin. (See dia­gram O)

Diagram O

3. The transmitter has 12 rows
of posts, each row has 3
posts. (see diagram P)

Diagram P

4. Use an opened paper clip to set the connectors numbered
1 through 9 so that the switches on the transmitter match
those on the receiver. To operate with Skylink #UR100, only
set to “ + ” or “ 0 ” position. Do not place the connector to
the middle & bottom posts “ - ” position. Leave the remaining
posts at “ 0 ”, or the blank position (remove the connectors).
See the Diagram J for details.

5. T est the transmitter with the Universal receiver .

PROGRAMMING THE SKYLINK MODEL #88, #88C

1. T o Program Your Keypad

- Open the cover on the
back. (See diagram Q)

CLOSE

OPEN

Diagram Q

2. Set brand jumper by moving the red plastic
tab to the number 7 jumper. Slide a n opened
paper clip into the
top of the red plastic
tab, then lift and re­position.

3. Set the frequency
switch located above
to “ D ” position (slide
the switch as far

DIP Switch Location

right as possible).
(See diagram R)

12345678

PROGRAMMING THE SKYLINK MODEL #88p

4. The connector (See diagram V) has 12 rows of posts, each row
has 3 posts. Each row contains one connector (See diagram
W). Set the code connectors from number 1 through 9 so that
the switches on the transmitter match those on the receiver.
T o operate with #UR100, only set the connectors to “ + ” or “0”
(blank position). Do not set the connectors to “ - ” positi on . L ea v e
the remaining posts at “ 0 ”, or the blank position (remove the
connectors). See the diagram L for details.

Diagram V

Diagram W

5. Refer to the keypad manual to test the transmitter with the Universal
receiver.

Frequency
Switch

Brand Jumper

Diagram R

WARNING

DO NOT let children
use any garage door
transmitter without
adult supervision.
Children can injure
themselves or others
by the garage door.

4. Use a pen or paper clip
to set the corresponding
DIP switches numbered
1 through 9 so that the
switches on the trans­mitter match those on
the receiver. Each switch
of the transmitter has 3
positions (“ + ”, “ 0 ”,
“ - ”). T o operate with
Skylink #UR-100, only
set the switches to “ + ”
or “ 0 ”. Do not use “ - ”
position.Leave the re­maining DIP switches in

WARRANTY

If, within one year from date
of purchase, this product
should become defective
(except battery), due to
faulty workmanship or
materials, it will be repaired
or replaced, without charge.
Proof of purchase is
required.

the transmitter at “0” or
the center position. (See
diagram S)

DIP Switch

Location

Diagram S

5. Refer to the keypad manual
to test the transmitter with
the Universal receiver.

The Universal Garage Door
Remote Control is approved
by the FCC and it complies
with Part 15 of the FCC
Rules. Its operation is
subject to the following two
conditions :

1. This device may not
cause harmful inter­ference.

2. This device must accept
any interference that
may cause undesired
operation.

PROGRAMMING THE SKYLINK MODEL #88p

1. T o Pr ogram Y our Keypad

- Open the cover on the
back. (See diagram T)

Diagram T

FCC

WARNING:

Changes or modifications
to this unit not expressly
approved by the party res­ponsible of compliance
could void the user’s
authority to operate the
equipment.

2. Set brand jumper by moving the red plastic
tab to the number 7 jumper. Slide an opened
paper clip into the
top of the red plastic

CLOSE

tab, then lift and re­position.

3. Set the frequency
switch located above

OPEN

to “ D ” position
(slide the switch

Code connector Location

as far right as
possible). (See
diagram U)

Skylink will not be held liable
or responsible for
any misuse or application
of this product other than
for its intended use.

SKYLINK
TECHNOLOGIES INC.

2213 Dunwin Drive,
Mississauga, Ontario
L5L 1X1, CANADA
[phone]
[phone] FAX
Email:[e-mail]
(Reply within 24 hrs)
Customer Service : [phone]
http://www.skylinkhome.com

P/N. 101A111-003 Rev.3
Patent no. 382251
Patents Pending
©1999 SKYLINK TECHNOLOGIES INC.

® are registered trademarks of their respective corporations

Frequency
Switch

12345678

Brand Jumper

Diagram U

®

GARAGE DOOR/

GATE OPENER

UNIVERSAL RECEIVER

USER'S INSTRUCTIONS

(Model UR-100)