Skylink PS-MT Installation Manual

INSTALLATION INSTRUCTIONS

Safety Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including
interferences that may cause undesired operation.

Package Contents

Motion Sensor

Model: PS-MT

Congratulations on your purchase of the Skylink Motion Sensor,

Model: PS-MT. The sensor will monitor any movement around your premises

and works with the SkylinkNet Internet Hub and the Skylink M-Series

Alert/Alarm System.

Section 1 - Insert a battery in the Motion Sensor

NOTE: The battery for the Sensor is not included. Please refer to
instruction below to insert an AA Alkaline Battery.

1. Use a coin to open the Motion Sensor cover.

WARNING:

Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

CE - DECLARATION OF CONFORMITY:

This equipment complies with the requirements relating to electromagnetic
compatibility, EN 301489-1, EN301489-3, EN300220-1, EN300220-2 and
EN60950-1. This equipment conforms to the essential requirement of the
1999/5/EC R&TTE Directive.

Section 2 - Programming the Sensor with M-Series Main Console

NOTE: You can program in total up to 4 sensors in one zone. If you try to
program the fth sensor, the rst sensor will be removed.

A

B

Parts

Description Quantity

A Motion Sensor 1

1Mounting AccessoriesB

Section 3 - Programming the Sensor with SkylinkNet Internet Hub

NOTE: Programming the sensor with the SkylinkNet Internet Hub
must be done from the SkylinkNet App.

2. Insert an AA Alkaline Battery.

Learn Button

1. Press the learn button on the back
of the M-Series Main Console for
3 seconds until the Zone 1 light
is ashing.

3. Open the Motion Sensor
cover with a coin and press the
learn button.

Zone LED

2. Zone 1 is selected. Press the learn
button to select the zone you want
to program the sensor.

4. Once the sensor is programmed,
the Main Console will beep once and
the corresponding zone led will be off.

1. Go to “More” and tap
on “System Settings”.

5. Tap on “Motion
Sensor”.

2. Tap on “Setup
Wizard”.

6. Name your Sensor,
location and tap
“Continue”.

3. Tap on “Add Device”.

7. Tap on “Learn Now”
and follow the video to
activate the sensor.

4. Tap on “Sensors”.

Section 4 - Testing the Sensor with M-Series Alert/Alarm System

Section 5 - Testing the Sensor with SkylinkNet Alarm System

Section 6 - Installing the Motion Sensor

Place the sensor in the appropriate location:

1. Slide the switch at the back
of the Main Console to
Alert Mode.

3. The Main Console will start
beeping and ash the Zone
LED.

2. Move in front of the motion
sensor to trigger the sensor. The
Led will ash when motion is
detected.

4. The motion sensor will stop
beeping and ashing the LED if there
is no motion detected for 15 seconds.

Section 7 - Battery Indication/Sensor Failure
M-Series Alert/Alarm System

NOTE: The corresponding zone LED in the Main Console will ash if a sensor
failure or low battery is occurred.

When a sensor failure occurs, try the following:

1. Check if the sensor is located at where it should be.

2. Check if there is any physical damage to the sensor.

3. Move the Main Console closer to the sensor, if the red LED stops ashing,
that means the Main Console or sensor needs to be relocated.

4. Replace the battery of the sensor if the Main Console does not respond
when the sensor is activated within short range.

1. Activate the sensor by
moving in front of the motion
sensor. The Led will ash
when motion is detected.

3. Don’t move in front of the
motion sensor for 15 seconds.

2. The blue icon will turn red indicating
that the motion is detected.

4. The red icon will turn back to blue
indicating that there is no motion
detected.

Troubleshooting M-Series Alert/Alarm System

Problem

The M-Series Main Console
panel does not respond to
the sensor?

Can I erase just one sensor
from a zone in the M-Series
Main Console?

I have multiple sensors in a
zone and the zone LED keep
ashing indicating a sensor
failure. How do I know which
sensor is having the
problem?

Solution

- You must program the sensor to the control
panel before they can work together.

- You must erase all the sensors in that zone
and then program the sensor you want to
keep.

- You need to test each sensor individually.

The motion sensor can be mounted with a double-sided tape or screws
in a corner, straight wall, ceiling or stand freely by itself.

Warranty

ONE YEAR WARRANTY

This product is guaranteed to be free of defects in materials and
workmanship for 1 year from the date of purchase. If this product is
defective, call 1-800-304-1187 for repair or replacement parts.
Guarantee does not include normal wear and tear or batteries.

If you have any questions, problems or missing parts,

please call Skylink Customer Support:

9:00am - 5:00pm EST, Monday-Friday.

Or e-mail us at [e-mail]

1-800-304-1187

www.skylinkhome.com

CUSTOMER SERVICE

17 Sheard Avenue,
Brampton, Ontario,
Canada L6Y1J3

P/N : 101Y144 Rev:0
©2014 SKYLINK GROUP.