SkyLink HA-434TL User Manual

lndoor/Outdoor

Motion

The

lndoor/Outdoor

around

outdoor.

along

with

ln this

joint,

head

Sensor

your

house. The

Once motion is

alert

beeping or alarm.

package,

screws.

Motion

you

should find

motion

detected, the

ru

lndoor/Outdoor

Motion Sensor

Please

follow

the instructions

The

sensor

Receiver

to

one

1. Plug

2. The

3.

Open the

learn
flash.

4. lf

sensor
on the

lf

5.

learn
program

6.

Once the

and none

must

before they

of the 4 zones. Follow

in

an

green

button for

You may

you

would

while the zone

back

you

would

button

the sensor to,

sensor is
of the red zone

programmed

be

AC

adapter to the

LED will be

back cover

5 seconds,

now release

like to

the

of

sensor

like to

again, until

can communication.

on indicating

and there is

program

1 red LED

program

programmed,

Sensor is

sensor

an lndoor/Outdoor

r

below to

to

the

instructions

receiver.

until both

the learn

the

sensor to

is flashing.

to activate

the

activate

LEDs

sensor

the

will be on.

the red LED

then

ModelHA-434TL

designed to monitor movement

receiver

joint

setup

the Household

it is turned

a learn

placed

can

be

either

will respond with flashing

Motion Sensor, ball-

2pcs

3xlSscrews

(tnctuded)

your

motion

sensor.

Long

Alert"

may

below:

on.

program

You

button. Press and hold this

green

LED

button.

zone 1 red LED

and

zone 1, activate the

it.

to

flashes

Press the

other

at the zone

SET

zones,

indoor

Range

the sensor

button

press

you

want

the sensor.

green

LED will

be steadily

the

on

or

to

MOUNTING

A

ball-head

A height

location is
provided.
of the
adjusted. Please

angle.

joint

of 7 tl is recommended,

selected,

Once the

sensor into

WALK TEST
After mounting

to

should

not

testing

to

sensor

slide

respond,

once, the

perform

is detecting

control how far

angle

12

be

occur if the

walk in

beep if

20

between

important

if the sensor

ln

order

adjusting the

move the

up to around

this may not
trigger may

You
Place the

receiver will
does
detected
detected tor
walk

is necessary

mount the

ball-head

the ball-head

refer to

the

sensor at the

a

joint

"Walk

walk test

the things

the sensor

the

of

sensor. To

downward. To

degrees. This

desired if the

sensor is

the

area that

switch

on the

the

sensor

adjust the mounting

sensor

seconds.

will not

Therefore,

2

activations.

to

mount the

depending

ball-head

is

joint.

Test" to

sensor

on

joint

to this location

mounted to

The

mounting

determine the

desired location,

in

to

order

increase the

will

sensor is

you

want to

can

reduce the

give

the maximum
placed

determine

"see",

range, move

set to detect

you

would

like the

side of the receiver

your

detects

movement.

angle accordingly.

be triggered

wait for

at least 20

by screws

slide

location.

the

back

at a desire

your

application. Once a

the wall,

angle can be

best mounting

-)

it is

detect.

this can be

detection range,

outdoors, since a false

motion in

sensor to monitor.

"Alert"

to

unless no motion

done by

simply

the sensor

range. However,

a distance.

position.

lf the receiver

After motion is

is

seconds

during

I

The

I

]'u

l

Plug

Note:

Each

fifth

sensor

Erasing

You

cannot

the

receiver,

all the

1.

Remove

2.

Open
release

3. while

4. You

may

5. You

in the

adapter to the receiver

Learn

Button

zone

into

a zone,

a

sensor

erase a specific

then

sensors

the

the

back cover,

from the

adapter from

the learn

holding

onto the learn

release

have

erased

program

can

program

button

the learn

all sensors

up to

the

first

sensor. You

the

ones

receiver:

the

press

and hold

until

button,

button when

lnsert

9V alkaline

4

sensors. lf

programmed

you

would like

receiver.

the learn

step 4.

plug

the

from

the

SET Button

(option)

battery

you

try to

sensor will

must

erase all sensors from

to keep. To

button.

in

the adapter to

LEDs

on the

receiver.

I

to the

program

be erased.

Do not

receiver.

the

receiver

sensor

erase

are on.

Perform
detected.

Tips:
heat or
heaters

a

SENSOR

The
placing
"Low"

"Low",

mended to

walk test
adjusted further.

result

low,

sensitivity

perform

the

walk

The

sensor

cold

etc.) that

Move

reduce

SENSITIVITY

sensitivity

the

connector

(connector

more

set the

result

shows

you

then

setting to

the

sensitivity

test in

the undesired

should not

producing

may

the

sensor

the range.

of the motion

position

movement

sensitivity

is

satisfied,

lf the

the

sensitivity is

can change

"High".

walk

test

setting.

face

(i.e.

devices

cause false

downward

to Move

sensor is

on either

"2")

the

position.

is required

"Low"

to

the

sensitivity

walk test

too

the

Please

after changing

area to ensure

towards

direct

NC or furnance

triggers

the

sensor

l2etogive

maximum range.

adjustable.

"High"

(connector

When

and

the

the

perform

to trigger

does not require

1-High

movement

sunlight,

vents, fans,

up to around

cannot be

placing

ovens,

change the setting

position

sensitivity is

"1")

set to

sensor. lt is recom-

"Walk

a

2-Low

Test". lf the

to

be

near

by

or

There are
Range

1) Alert

3 different operating modes for the Household Alert@ Long

Receiver.

-

Beeps when

will also flash.

2) Alarm - Sounds
zone LED

3) Off

Zone LED

To select

will also flash.

-

No

audio sound

will flash to indicate the

the

operating mode,

slide switch on the

-

No Audio

OFF

ALERT - Alert

Mode

ALARM - Alarm Mode

Operation

Alert
When motion

signal

flash for

will

lf the sensor is

the receiver

and

"beep", pause.....

lf the sensor is

will

emit a continuous

"beep

is detected in the monitored

to the receiver. lt will

15

seconds.

set to zone

will emit a continuous

etc.

set to zone

beep

beep beep"

a sensor is activated,

an alarm

when

a sensor is

will

be emitted when

activated sensor.

place

side

at the

the

desired setting:

area,

beep and the corresponding zone

1, zone

1 red LED on the receiver will

"single

4,

zone 4 red LED will

"4

beeps", i.e.
pause

"beep

......etc.

beep

corresponding

zone

activated, corresponding

is

sensor

the

sensor

activated.

will send a

red LED

flash,

"beep"

i.e.

beep",

flash, and the

beep beep"

pause,

receiver

pause

LED

The Household
different sensors:

Alert@ Long Range Receiver

garage

door monitor

water sensor, indoor/outdoor
www.skylinkhome.com

more information of how

This device complies with Part
following two conditions:

(2)

This

device must accept

may cause undesired
WARNING:

Changes
responsible

NOTE:
This equipment has been tested
digital device,
provide

This equipment
installed and used in
ference to

However,
installation.

reception,

encouraged

-

-

-

-

or modifications to this

for

compliance could void the user's authority to operate the equipment.

pursuantto

reasonable

generates,

radio

communications.

there is

lf this

which

can be determined by turning

to try to

Reorient or relocate
lncrease the separation

the

Connect

receiver is

Consult

equipment into

connected.

the dealer

or contact us at [e-mail] for

to fully utilize

(1)This

any

operation.

Part 15

protection

no

equipment dose cause harmful interference

correct the interference by

or an experienced radioffV

against harmful interference in a residential installation

uses and can radiate radio frequency energy and,

accordance with the instructions, may cause harmful inter-

guarantee

the receiving antenna.

between the equipment and receiver.

an outlet on a circuit different from that to which the

can work with up to 4

motion sensor,

15 of the FCC Rules.

device may not cause harmful interference, and

interference

not

unit

expressly approved by the

found

and

the FCC Rules. These limits

of

that interference will

etc.

your

lndoor/Outdoor Motion

received, including interference that

to comply with the limits for a Class

not occur in a

the equipment off and on, the user

more

one or

technician for help.

sensor, door /

window

Please visit

Operation

to radio or television

following measures:

of the

sensor,

is

subject

party

are designed

particular

to the

Sensor.

B

to

if not

is

By the number

of beeps emitted by the receiver,

zone is triggered.

Mute

When a

buzzer by

you

sensor is triggered for

pressing

can disable

lhe buzzer for

the mute button.

For instance,
garage, you
buzzer
press

the

sound.

the receiver

you

if

may want to

garage

for

this

"Mute"

lf

any

other sensor is triggered,

will

sound again.

Alarm

When the receiver
when a sensor

minutes. To

is

terminate

button. Although

activated,
Note: This

rather

turning

its

corresponding LED

audio

an alert

signal indicating

off the

siren does not require

off

the mute button. When

a long

all currently activated

The receive will

are working in

beep again if

your

disable the

only. Then

button after it

is in Alarm

activated.

the siren

the

alarm siren is terminated,

you

starts to

operation mode,

The

maximum

during the

will continue

is

siren

not intended

a

sensor

user can

period

of time,

another

it receives another signal.

can

it will

alarm

duration is set for 3

3-min interval,

if

that sensor is still

to flash.

prevent

to

specific

intruder

is

activated. Therefore,

password.

identify which

you

may

stop

the

signal comes again.

its

press

break-in,

pressing

siren

the mute

it

sensors by

sound

lf, within

(except

replaced, without

you

lf

work or

1. visit our FAQ

2. email

3. call ourtollfree

Fax

is

year

one

from

battery), due to faulty

like

would

download information

at

us

(800)

286-1

date of

charge. Proof

to

order Skylink's

section at www.skylinkhome.com,

[e-mail],

at 1-800-304-1187 from

320

purchase,

workmanship

of

and user manual,

this

purchase

or

and a Return Authorization

products

or

Monday to Friday,

product

should become defective

materials,

or have difficulty

please

or

:

it will be repaired or

are

getting

9 am to 5

required.

them to

pm

EST.

No audio will

When the
sensor
signal"

battery

is

out

indication.

i.e. if zone 1

When the loss
corresponding

ing rapidly,

"loss

that means

of signal"

be emitted

even sensor is activated.

level on the

sensor drops to

of the operating range,

The

red LED representing

sensor is lost, the zone

of

signal

indication

sensor and trigger that

the receiver

indication

persists,

Only zone LED will

a certain

the receiver will

show a

that zone will flash rapidly,

1 red LED will flash rapidly.

occurs,

move the receiver closer

sensor. lf the red LED

or sensor needs

replace the

to be

battery of that sensor.

level,

or

the

"loss

stops

relocated. lf the

flash.

of

to

flash-

CUSTOMER SERVICE

17

the

Sheard

Email :support

http;//www.skyl i n khome.
P/N.1Un54

SKYLINK GROUP

O2O1O

Avenue,

Brampton,

skylinkhome.com

@

Ontario, Canada L6Y

com

1J3