Operating Instructions
PRN0354 Rev. 3.1 July 2011
977EA
SKOPE Bathroom Fan Heater
2
977EA
SKOPE Bathroom Fan Heater
Introduction
Designed for easy installation, your SKOPE 977EA Bathroom Fan
Heater incorporates a unique wall-mounting hinged chassis, making
installation faster and easier. This upgraded bathr oom fa n he ater has
been designed to cover the footprin t of the pr ev iou s SKOPE mod e l.
See separate Installation Instructions for wiring options.
Safety Information
When using any electrical appliance, safety precautions should always
be observed. Read these instructions carefully, and retain for future
reference. For service, contact your nearest authorised service agent.
• Under no circumstances should an una uthorised person open the
heater, in order to adjust the thermostat.
• When used by, or near, youn g children or infirm persons, close
supervision is necessary. Young children should be supervised to
ensure that they do not play with the appliance.
• Do NOT use this appliance other than for its intended use.
• Use this appliance with the voltage specified on the rating label.
• Be very careful not to touch hot surfaces or moving p arts.
• Do NOT cover the grilles or place any object or material up against
the unit, as this may block entry or exhaus t of airflo w.
• Do NOT probe any opening to remove fluf f. To ensure trouble-free
performance it is recommended that on a regu lar ba sis the unit b e
isolated from the power supply and a vacuum cleaner used to
remove dust and fluff from the inlet and outlet grilles.
• Regulations require that electrical work be carried out b y
authorised persons. For your own safety and that of others, en sure
this is done.
• Do NOT allow the supply cord to come into contact with heated
surfaces during operation.
• If the supply cord becomes damaged, it must be replaced by a
SKOPE authorised service agent, or similarly qualified person, in
order to avoid a hazard.
3
977EA
SKOPE Bathroom Fan Heater
Safety Cutout
Your SKOPE 977EA Bathroom Fan Heater is fitted with a n auto- reset
thermal cutout and a fusible link. Either of these devices will
automatically switch off the elements, should the unit reach an
abnormal temperature. Should this occur:
1. Disconnect heater from powe r sup p l y
2. Check for blockage of the air inlet and outlet
3. Use a vacuum cleaner to clean if necessary
If the heater still fails to operate, contact your nearest authorised
service agent.
Operation
Air is drawn through the slots in the cover of the heater by an axial fan,
blown over heating elements and then blown out through the bottom
louvred grille into the room. The heater is controlled by the pull-cord
switch.
The heat output is regulated by an internal, step-do wn thermostat
which will reduce the output from 2200-2400 Watts to 1100-1200 Watts
when a comfortable room temperature is reached.
Care
The heater is best wiped down from time to time with a damp cloth. Do
not use any abrasive cleaners.
4
977EA
SKOPE Bathroom Fan Heater
Specifications: model 977EA
SKOPE Industries Limited reserve the right to alter specifications without notice.
Contact Addresses
Electrical
Supply: 230-240 Volts a.c. 50 Hz.
Wattage: 2200-2400W, thermostatically reduced to 1100-1200W.
Wiring: 600mm flexible cord fitted with 3-pin plug
Ingress Protection Rating: IPX1
Dimensions
Height: 218mm
Width: 346mm
Depth: 112mm
Weight: 2.7 kg
SKOPE INDUSTRIES LIMITED
New Zealand
Head Office
PO Box 1091, Christchurch
New Zealand
Freephone: 0800 947 5673
Fax: (03) 983 3896
Email: enquiry@skope.co.nz
Website: www.skope.co.nz
Australia
A.B.N. 73 374 418 306
PO Box 7543, Baulkham Hills
NSW 2153, Australia
Freephone: 1800 121 535
Freefax: 1800 121 533
Email: enquiry@skope.com.au
Website: www.skope.com.au
Loading...