SIMPLY CLEVER
ŠkodaYeti
OWNER‘S MANUAL
A-SUV_11_09.indd 3A-SUV_11_09.indd 3 9.9.2009 13:57:279.9.2009 13:57:27
Introduction
You have opted for a Škoda - our sincere thanks for your confidence in us.
Your new Škoda offers you a vehicle featuring the most modern engineering and a wide range of equipment which
you will undoubtedly wish to use to the full during your daily motoring. That is why, we recommend that you read
this Owner's Manual attentively to enable you to become familiar with your car and all that it offers as quickly as
possible.
Please do not hesitate to contact your specialist garage or importer should you have any further questions or any
problems regarding your vehicle which may arise. He will be ready at any time to receive your questions, suggestions and criticisms.
National legal provisions, which deviate from the information contained in these operating instructions, take precedence over the information contained in the operating instructions.
We wish you much pleasure with your Škoda and pleasant motoring at all times.
Yo ur Škoda Auto
sgg.6.book Page 1 Thursday, September 24, 2009 2:32 PM
Introduction2
On-board literature
The on-board literature for your vehicle consists of this “Owner's Manual”
as well as a “Service schedule” and a “Help on the road”. There can also be
a variety of other additional operating manuals and instructions on-board
(e.g. an operating manual for the radio) depending on the vehicle model and
equipment.
If one of the publications listed above is missing, please contact a specialist
garage immediately, where one will be glad to assist you in such matters.
One should note that the details given in the vehicle's papers always
take precedence over those in the Owner's Manual.
Owner's Manual
This Owner's Manual describes the current scope of equipment. Certain
items of equipment listed are only installed later on and only envisaged for
particular markets. The illustrations can differ in minor details from your
vehicle; they are only intended for general information.
In addition to information regarding all the controls and equipment, the
Owner's Manual also contains important information regarding care and
operation for your safety and also to retain the value of your vehicle. To
provide you with valuable tips and aids. You will learn how you can operate
your vehicle safely, economically and in an environmentally conscious
way.
For safety reasons, please also pay attention to the information on
accessories, modifications and replacement of parts ⇒ page 221.
The other chapters of the Owner's Manual are also important, however, for
proper treatment of your car - in addition to regular care and maintenance helps to retain its value and in many cases is also one of the conditions for
possible warranty claims.
The Service schedule
contains:
• Vehicle data;
• Service intervals;
• Overview of the service work;
• Service proof;
• Confirmation of mobility warranty (only valid in certain countries);
• important information on the warranty.
The confirmations of the carried out service work are one of the conditions
for possible warranty claims.
Please always present the Service schedule when you take your car to a
specialist garage.
If the Service schedule is missing or worn, please contact the specialist
garage where your car is serviced regularly. You will receive a duplicate, in
which the previously carried out service work are confirmed.
Help on the road
contains the most important telephone numbers in individual countries as
well as the addresses and telephone numbers of Škoda importers.
sgg.6.book Page 2 Thursday, September 24, 2009 2:32 PM
Contents 3
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Contents
Layout of this Owner's Manual
(explanations)
. . . . . . . . . . . . . . . . . . . . . . . . . .
Using the system . . . . . . . . . . . . . . . . . . . . . .
Cockpit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The brief instruction . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic functions and important information . . . . .
Instruments and Indicator/Warning Lights . . .
General view of the instrument cluster . . . . . . . . .
Engine revolutions counter . . . . . . . . . . . . . . . . . . . .
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant temperature gauge . . . . . . . . . . . . . . . . . . .
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Counter for distance driven . . . . . . . . . . . . . . . . . . .
Service Interval Display . . . . . . . . . . . . . . . . . . . . . . .
Digital clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-functional indicator (onboard computer) .
Information display* . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Check Control* . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unlocking and locking . . . . . . . . . . . . . . . . . . . . . . . .
Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the battery of the radio remote control
Electronic immobiliser . . . . . . . . . . . . . . . . . . . . . . . .
Child safety lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central locking system . . . . . . . . . . . . . . . . . . . . . . . .
Remote control* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Synchonisation of the remote control . . . . . . . . . .
Anti-theft alarm system* . . . . . . . . . . . . . . . . . . . . . .
Power windows* . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric sliding/tilting roof with electric sun screen*
Lights and Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wiper and wash system . . . . . . . . . . . . .
Rear-view mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seats and Stowage . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting front seats electrically* . . . . . . . . . . . . . . .
Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Middle rear head restraint* . . . . . . . . . . . . . . . . . . . .
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage compartment . . . . . . . . . . . . . . . . . . . . . . . .
Variable loading floor* . . . . . . . . . . . . . . . . . . . . . . . . .
Variable loading floor* with spare wheel* . . . . . . .
Roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cigarette lighter*, power sockets . . . . . . . . . . . . . . .
Storage compartments . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage compartment on the front passenger side
Cooling of storage compartment on front passenger
side* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage compartment on the dash panel* . . . . . . .
Storage compartment in front centre console . . .
Storage compartment for spectacles* . . . . . . . . . . .
Storage compartment in the front and rear doors
Storage compartment below front passenger seat*
Front seat armrest with storage compartment* . .
Storage compartment in rear centre console* . . .
Storage compartments in the luggage compartment*
Flexible storage compartment* . . . . . . . . . . . . . . . .
Clothes hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removeable through-loading bag* . . . . . . . . . . . .
Heating and air conditioning system . . . . . . . . .
Air outlet vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climatic* (semi-automatic air conditioning system)
Climatronic* (automatic air conditioning) . . . . . .
Auxiliary heating (auxiliary heating and ventilation)*
Starting-off and Driving . . . . . . . . . . . . . . . . . . . . . . .
Setting steering wheel position . . . . . . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching off the engine . . . . . . . . . . . . . . . . . . . . . . .
Shifting (manual gearbox) . . . . . . . . . . . . . . . . . . . . .
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear parking aid* . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front and rear parking aid* . . . . . . . . . . . . . . . . . . . .
Park Assist* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cruise control system (CCS)* . . . . . . . . . . . . . . . . . .
Automatic gearbox DSG* . . . . . . . . . . . . . . . . . . . . .
Automatic gearbox DSG* . . . . . . . . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multifunction steering wheel* . . . . . . . . . . . . . . . . .
Universal telephone preinstallation GSM II* . . . . .
Voice control of the telephone . . . . . . . . . . . . . . . . .
Inputs AUX-IN* and MDI* . . . . . . . . . . . . . . . . . . . . .
CD changer* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passive Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correct seated position . . . . . . . . . . . . . . . . . . . . . . .
6
7
9
9
11
11
16
16
17
17
17
17
18
18
20
20
24
26
29
39
39
39
40
40
40
45
46
46
47
50
53
53
60
62
63
66
69
69
70
72
73
74
77
78
82
83
84
85
86
86
87
88
88
89
89
89
90
90
90
91
91
92
92
92
93
93
95
95
96
98
101
105
109
109
109
110
111
112
112
113
114
115
119
121
121
126
126
129
132
135
135
137
137
137
138
sgg.6.book Page 3 Thursday, September 24, 2009 2:32 PM
Contents4
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Why seat belts? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The physical principle of a frontal collision . . . . . .
Important safety information regarding the use of seat
belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How are seat belts correctly fastened? . . . . . . . . . .
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description of the airbag system . . . . . . . . . . . . . . .
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver's knee airbag* . . . . . . . . . . . . . . . . . . . . . . . . .
Side airbags* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Head airbags* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating an airbag . . . . . . . . . . . . . . . . . . . . . . . .
Transporting children safely . . . . . . . . . . . . . . . . . .
What you should know about transporting children!
Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching a child seat using the “ISOFIX” system .
Attaching child seat using the “Top Tether” system
Driving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intelligent Technology . . . . . . . . . . . . . . . . . . . . . . . .
Electronic stability programme (ESP)* . . . . . . . . . .
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake booster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antilock brake system (ABS) . . . . . . . . . . . . . . . . . . .
Brake Assist* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uphill-Start off-Assist* . . . . . . . . . . . . . . . . . . . . . . . .
Electromechanical power steering . . . . . . . . . . . . .
Tyre inflation pressure-control system* . . . . . . . . .
Diesel particle filter* (diesel engine) . . . . . . . . . . . .
Off-road* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving and the Environment . . . . . . . . . . . . . . . . .
The first 1 500 kilometres and then afterwards . .
Catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving in an economical and environmentally
conscious manner . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental compatibility . . . . . . . . . . . . . . . . . . .
Motoring abroad . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Avoiding damage to your vehicle . . . . . . . . . . . . . . .
Driving through bodies of water on roads . . . . . . .
Off-road driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing a tra il er . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Maintenance . . . . . . . . . . . . . . .
Taking care of your vehicle and cleaning the
vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care of the exterior of vehicle . . . . . . . . . . . . . . . . . .
Care of the interior of vehicle . . . . . . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspecting and replenishing . . . . . . . . . . . . . . . . . . .
Engine compartment . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield washer system . . . . . . . . . . . . . . . . . . . . .
Wheels and Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories, changes and replacement of parts
Accessories and replacement parts . . . . . . . . . . . . .
Technical changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicles of the group N1 . . . . . . . . . . . . . . . . . . . . . . .
Breakdown assistance . . . . . . . . . . . . . .
Breakdown assistance . . . . . . . . . . . . . . . . . . . . . . . . .
Space for first-aid box* and warning triangle* . . .
Fire extinguisher* . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spare wheel* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tow-starting and towing vehicle . . . . . . . . . . . . . . .
Fuses and light bulbs . . . . . . . . . . . . . . . . . . . . . . . . .
Electric fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General information . . . . . . . . . . . . . . . . . . . . . . . . . .
Used abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification details . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel consumption according to the regulations
(99/100/EU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other information . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine oil specifications . . . . . . . . . . . . . . . . . . . . . . .
1.2 ltr./77 kW TSI - EU°5 . . . . . . . . . . . . . . . . . . . . . . .
1.8 ltr./118 kW TSI - EU 5 . . . . . . . . . . . . . . . . . . . . . .
2.0 ltr./81 kW TDI CR - EU°5 . . . . . . . . . . . . . . . . . . .
2.0 ltr./103 kW TDI CR - EU°5 . . . . . . . . . . . . . . . . . .
2.0 ltr./125 kW TDI CR - EU°5 . . . . . . . . . . . . . . . . . .
Yeti - Vehicles of the group N1 . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
141
141
141
142
143
146
146
147
149
150
152
154
156
156
158
161
162
163
163
163
166
167
167
168
168
168
169
170
170
173
173
174
174
178
178
179
179
180
190
190
193
193
193
193
197
200
200
200
201
203
203
205
207
209
210
214
215
215
221
221
221
221
223
223
223
223
223
224
224
225
229
230
233
233
238
243
243
243
243
243
243
243
244
245
245
246
247
249
251
253
255
257
259
sgg.6.book Page 4 Thursday, September 24, 2009 2:32 PM
Contents 5
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
sgg.6.book Page 5 Thursday, September 24, 2009 2:32 PM
Layout of this Owner's Manual (explanations)6
Layout of this Owner's Manual (explanations)
The Owner's Manual has been systematically designed, in order to make it easy for you
to find and absorb the information you require.
Chapters, table of contents and subject index
The text of the Owner's manual is divided into relatively short sections which are
combined into easy-to-read chapters. The chapter you are reading at any particular
moment is highlighted at the bottom right of the page.
The Table of contents is arranged according to the chapters and the detailed Subject
index at the end of the Owner's Manual helps you to rapidly find the information you
are looking for.
Sections
The majority of Sections apply to all models.
Since there is a wide range of different equipment and options available it is clearly
unavoidable, despite dividing the contents into sections, that mention may be made
of equipment which is not fitted to your vehicle.
Brief information and instructions
Each section has a Heading.
This is followed by Brief information (in large italic lettering), which tells you the
subject which is dealt with in this section.
Most of the illustrations are accompanied by an Instruction (in relatively large letters)
which explains to you in a straightforward way the action you have to take. Work steps
which have to be carried out are illustrated with a hyphen.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of
travel of the vehicle.
Explanation of symbols
* Equipment which is marked in such a way is only standard on certain vehicle model
versions or only suppliable as optional equipment for certain models.
End of a section.
The section is continued on the next page.
Notes
All four kinds of notes, which are used in the text, are always stated at the end of the
respective section.
WARNING
The most important notes are marked with the heading WARNING. These
WARNING notes draw your attention to a serious risk of accident or injury.
While reading the text you will frequently encounter a double arrow followed
by a small warning symbol. This symbol is intended to draw your attention to a
WARNING note at the end of the section to which you must pay careful attention.
Caution
A Caution note draws your attention to the possibility of damage to your vehicle (e.g.
damage to gearbox), or points out general risks of an accident.
For the sake of the environment
An Environmental note draws your attention to environmental protection aspects.
This is where you will, for example, find tips aimed at reducing your fuel consumption.
Note
A normal Note draws your attention in a general way to important information.
sgg.6.book Page 6 Thursday, September 24, 2009 2:32 PM
7
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Using the system
sgg.6.book Page 7 Thursday, September 24, 2009 2:32 PM
Cockpit8
Fig. 1 Certain items of equipment shown in the illustration are only fitted to particular model versions or are optional items of equipment.
sgg.6.book Page 8 Thursday, September 24, 2009 2:32 PM
Cockpit 9
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Cockpit
Overview
This overview will help you to quickly familiarise yourself with the
displays and the control elements.
Electric exterior mirror adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air outlet vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever for the multi-functional switch:
− Turn signal light, headlight and parking light, headlight flasher . .
− Cruise control system* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel:
− with horn
− with driver airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− with pushbuttons for radio, navigation system and mobile phone*
Instrument cluster: Instruments and indicator lights . . . . . . . . . . . . . .
Lever for the multi-functional switch:
− Multi-functional indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Windshield wiper and wash system . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air outlet vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control dial for heating on the driver's seat* . . . . . . . . . . . . . . . . . . . . .
Switch for hazard warning lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator light for a switched off front seat passenger airbag . . . . . . .
Storage compartment on the dash panel* . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Radio*
− Navigation*
Control dial for heating on the front passenger seat* . . . . . . . . . . . . . .
Storage compartment on the front passenger side . . . . . . . . . . . . . . . .
Front passenger airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch for the front passenger airbag (in front passenger storage
compartment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric power-operated window* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse box (on side of dash panel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bonnet release lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control dial for the instrument lighting and control dial for the headlight
beam range regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever for adjusting the steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver's knee airbag* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Switch for the ESP* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Switch for TCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front and rear parking aid* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central locking switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Gearshift lever (manual gearbox) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Selector lever (automatic gearbox*) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Offroad* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tyre inflation pressure-control system* . . . . . . . . . . . . . . . . . . . . . . . . . .
Park Assist* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Operating controls for the heating . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Operating controls for Climatic* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Operating controls for Climatronic* . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note
• Equipment whi ch is marked * is only standard on certain vehicle model versions or
only suppliable as optional equipment for certain models.
A
1
67
A
2
95
A
3
59
119
A
4
147
126
A
5
16
A
6
20
63
A
7
95
A
8
77
A
9
58
A
10
154
A
11
89
A
12
A
13
77
A
14
89
A
15
147
A
16
154
A
17
14
A
18
233
A
19
53
A
20
203
A
21
57, 58
A
22
11
A
23
149
A
24
109
A
25
163
165
A
26
114
A
27
43
A
28
112
122
A
29
90
A
30
170
A
31
169
A
32
115
A
33
96
98
101
sgg.6.book Page 9 Thursday, September 24, 2009 2:32 PM
Cockpit10
• Cars with factory-fitted radio or navigation system are supplied with separate
instructions for operating such equipment.
• The arrangement of the controls and switches and the location of some items on
right-hand drive models may differ from that shown in ⇒ page 8, fig. 1. The symbols
on the controls and switches are the same as for left-hand drive models.
sgg.6.book Page 10 Thursday, September 24, 2009 2:32 PM
The brief instruction 11
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The brief instruction
Basic functions and important information
Introduction
The chapter of the brief instruction is only used as a quick reference of
the most important operating elements of the vehicle. It is necessary to
observe all the information which is contained in the following chapters
of the Owner's Manual.
Unlocking and locking the vehicle
Unlocking the vehicle
Unlocking the boot lid
Locking the vehicle
Folding out/folding up of the key
Further information ⇒ page 45, “Unlocking and locking car”.
Setting steering wheel position
Fig. 3 Adjustable steering wheel: Lever on the steering column / the correct distance of the
driver from the steering wheel
You can set the height and the forward/back position of the steering wheel to the
desired position.
– Pull the lever below the steering column ⇒ fig. 3 down.
– Set the steering wheel to the desired position (concerning height and forward/back
position).
– Push the lever upwards as far as the stop.
Further information ⇒ page 109, “Setting steering wheel position”.
WARNING
• Adjust the steering wheel so that the distance between the steering wheel
and your chest is at least 25 cm ⇒ fig. 3 on the right. Not maintaining this
minimum distance will mean that the airbag system will not be able to properly
protect you - hazard!
• You must not adjust the steering wheel when the vehicle is moving!
• For safety reasons the lever must always be firmly pushed up to avoid the
steering wheel altering its position unintentionally when driving - risk of
accident!
Fig. 2 Remote control key
A1A2A3A
4
sgg.6.book Page 11 Thursday, September 24, 2009 2:32 PM
The brief instruction12
Seat belt height adjuster
– Move the height adjuster in the desired direction up or down ⇒ fig. 4.
– Then pull firmly on the belt to ensure that the seat belt height adjuster has correctly
locked in place.
Further information ⇒ page 143, “Seat belt height adjuster”.
WARNING
Adjust the height of the belt in such a way that the shoulder part of the belt is
positioned approximately across the middle of your shoulder - on no account
across your neck!
Adjusting the front seats
Adjusting a seat in a forward/back direction
Adjusting height of seat
Adjust the angle of the seat backrest
Adjusting lumbar support*
Further information ⇒ page 69, “Adjusting the front seats”.
WARNING
Only adjust the driver seat when the vehicle is stationary - risk of injury!
Electric exterior mirror adjustment*
Further information ⇒ page 67, “Exterior mirror”.
Fig. 4 Front seat: Seat belt height
adjuster
Fig. 5 Controls at seat
Heating of the external mirror*
Adjusting left and right exterior mirrors simultaneously
Adjusting the right-hand exterior mirror
Switching off operating control
A1A2A3A
4
Fig. 6 Inner part of door: Rotary knob
sgg.6.book Page 12 Thursday, September 24, 2009 2:32 PM
The brief instruction 13
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Switching lights on and off
Further information ⇒ page 53, “Switching lights on and off ”.
Turn signal and main beam lever
Turn signal light right
Turn signal light left
Switching over between low beam and main beam lights
Headlight flasher
Further information ⇒ page 59, “The turn signal and main beam lever ”.
Windscreen wiper lever
Intermittent switch, sensitivity setting rain sensor*
Wipers off
Intermittent wipe
Automatic light control*
Switching off all lights/daylight driving lights
Switching on side lights
Switching on the low beam and main beam
Fog lights*
Rear fog light
Fig. 7 Dash panel: Light switch Fig. 8 Turn signal and main beam lever
AAABACA
D
Fig. 9 Windscreen wiper lever
AAA0A
1
sgg.6.book Page 13 Thursday, September 24, 2009 2:32 PM
The brief instruction14
Slow wipe
Fast wipe
one time wipe
Automatic wipe/wash
Rear window wiper
Intermittent wipe - every 6 seconds
Automatic wipe/wash
Further information ⇒ page 63, “Windshield wiper”.
Power windows*
Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window in the rear door on the right*
Button for the power window in the rear door on the left*
Safety pushbutton*
Further information ⇒ page 47, “Power windows*”.
Refuelling
Fig. 11 Right rear side of the vehicle: Fuel filler flap / fuel filler flap with cap unscrewed
– Press in the middle of the left area of the fuel filler flap in direction of arrow
⇒ fig. 11.
– The fuel filler cap on the fuel filler tube must be unlocked to the left using the
vehicle key (only valid for vehicles which do not have automatic unlocking of the
fuel filler flap).
– Unscrew the fuel filler cap anti-clockwise and place the fuel filler cap from above
on the fuel filler flap ⇒ fig. 11 on the right.
Further information ⇒ page 201, “Refuelling”.
Bonnet remote release
– Pull the unlocking lever below the dash panel on the driver's side ⇒ fig. 12.
A2A3A4A
5
A6A
7
Fig. 10 Buttons on the driver's door
AAABACADA
S
Fig. 12 Bonnet release lever
sgg.6.book Page 14 Thursday, September 24, 2009 2:32 PM
The brief instruction 15
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Opening the bonnet
Fig. 13 Radiator grille: Locking lever / securing the bonnet with the bonnet support
– Pressing on the locking lever in direction of arrow ⇒ fig. 13 will unlock the
bonnet.
– Take the bonnet support out of its holder in direction of arrow and secure the
opened bonnet by inserting the end of the support in the opening designed for
it ⇒ fig. 13.
Further information ⇒ page 203, “Opening and closing the bonnet”
Inspecting the engine oil level
Engine oil must not be refilled.
Engine oil can be refilled.
Engine oil must be refilled.
Further information ⇒ page 205, “Check engine oil level”.
A1A2A
3
Fig. 14 Dipstick
AAABA
C
sgg.6.book Page 15 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights16
Instruments and Indicator/Warning Lights
General view of the instrument cluster
Engine revolutions counter ⇒ page 17
Speedometer ⇒ page 17
Button for display mode:
− Set hours / minutes
− Activating / deactivating the second speed in mph or km/h*
− Service interval - Display of the remaining number of days, kilometres or miles
to the next Inspection Service / Reset*
1)
Coolant temperature gauge ⇒ page 17
Display
− with counter for distance driven ⇒ page 18
− with Service Interval Display ⇒ page 18
− with digital clock ⇒ page 20
− with Multi-functional indicator* ⇒ page 20
− with Information display* ⇒ page 24
Fuel gauge ⇒ page 17
Button for:
− Reset trip counter for distance driven
− Resetting Service Interval Display
− Set hours / minutes
− Activate / deactivate display mode
Fig. 15 Instrument cluster
1)
Valid for countries where the values are indicated in British measuring units.
A
1
A2A3A
4
A
5
A6A
7
sgg.6.book Page 16 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 17
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Engine revolutions counter
The red zone of the rev counter scale ⇒ page 16, fig. 15 indicates the range in
which the engine control unit begins to limit the engine speed. The engine control unit
restricts the engine speed to a steady limit value.
Shift into the next higher gear or select the selector lever position D of the automatic
gearbox before reaching the red zone of the rev counter scale.
Avoid high engine speeds during the driving time and before the engine has been
warmed up to operating temperature ⇒ page 173.
For the sake of the environment
Shifting up early helps you save fuel and reduce the operating noise of your vehicle.
Speedometer
Warning against excessive speeds*
An acoustic warning signal will sound when the vehicle speed exceeds 120 kilometres
per hour. The acoustic warning signal will switch off again when the vehicle speed goes
below this speed limit.
Note
This function is only valid for some countries.
Coolant temperature gauge
The coolant temperature gauge ⇒ page 16, fig. 15 operates only when the ignition
is switched on.
In order to avoid any damage to the engine, please pay attention to the following notes
regarding the temperature ranges:
Cold range
If the pointer is in the left-hand area of the scale it means that the engine has not yet
reached its operating temperature. Avoid running at high engine speeds, at full throttle
and at severe engine loads.
The operating range
The engine has reached its operating temperature as soon as the pointer moves into
the mid-range of the scale. The pointer may also move further to the right at high
engine loads and high outside temperatures. This is not critical provided the warning
symbol in the instrument cluster does not flash.
If the symbol in the instrument cluster flashes it means that either the coolant
temperature is too high or the coolant level is too low. Observe the guidelines
⇒ page 34, “Coolant temperature/ Coolant quantity ”.
WARNING
Pay attention to the warning notes ⇒ page 204, “Working in the engine
compartment” before opening the bonnet and inspecting the coolant level.
Caution
Additional headlights and other attached components in front of the fresh air inlet
impair the cooling efficiency of the coolant. There is then a risk of the engine overheating at high outside temperatures and high engine loads!
Fuel gauge
The fuel gauge ⇒ page 16, fig. 15 only operates when the ignition is switched on.
The fuel tank has a capacity of about 60 litres. The warning symbol in the instrument
cluster lights up when the pointer reaches the reserve marking. There are now about
10.5 litres of fuel remaining in the tank. This symbol is a reminder for you, that you
must refuel.
The following will be displayed in the information display*:
Please refuel!
An audible signal sounds as an additional warning signal.
A1A4A
6
sgg.6.book Page 17 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights18
Caution
Never run the fuel tank completely empty! The irregular supply of the fuel system can
lead to irregular running of the engine. Unburnt fuel may get into the exhaust system
and damage the catalytic converter.
Note
After filling up, it can occur that during dynamic driving (e.g. numerous curves, braking,
driving downhill and climbing a steep hill) the fuel gauge indicates approx. a fraction
less. When stopping or during less dynamic driving, the correct fuel supply quantity is
indicated. This effect is not a fault.
Counter for distance driven
The distance which you have driven with your vehicle is shown in kilometres (km). In
some countries the measuring unit “mile” is used.
Reset button
If you hold the reset button ⇒ page 16, fig. 15 pressed for about 1 second, the trip
counter is set back to zero.
Trip counter for distance driven
The trip counter indicates the distance which you have driven ⇒ fig. 16 since this
counter was last reset - in steps of 100 metres or 1/10 of a mile.
Counter for distance driven
The counter for distance driven ⇒ fig. 16 indicates the total distance in kilometers or
miles which the vehicle has driven.
Fault disp lay
If there is a fault in the instrument cluster, a constant text will appear in the display
Error. Have the fault rectified as soon as possible by a specialist workshop.
WARNING
Never seek to adjust the trip counter for distance driven while driving for safety
reaso ns!
Note
If vehicles which are fitted with the information display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the
counter for the total distance driven.
Service Interval Display
Depending on the equipment installed in the vehicle, the text can differ on the display.
Service Interval Display
Before the next service interval a key symbol and the remaining kilometers are
indicated after switching on the ignition ⇒ fig. 17. At the same time, a display appears
regarding the remaining days until the next service interval.
Fig. 16 Display: Counter for distance
driven
A
7
Fig. 17 Service Interval Display: Note
sgg.6.book Page 18 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 19
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The following will be displayed in the information display*:
Service in ... km or... days
The kilometre indicator or the days indicator reduces in steps of 100 km. or days until
the service due date is reached.
A flashing key symbol
and the text Service appears in the display for 20 seconds
as soon as the due date for the service is reached.
The following will be displayed in the information display*:
Service now!
Display regarding the distance and days until the following service interval
You can use the button to display the remaining distance driven and the days until
the next service interval ⇒ page 16.
A key symbol and a display regarding the remaining kilometers appear for 10
second in the display. At the same time, a display appears regarding the remaining days
until the next service interval.
On vehicles which are equipped with information display*, you can call up this information in the following menu on ⇒ page 24:
SETUP (Settings)
Service Interval (Service)
Info
The following will be displayed in the information display* for 10 seconds:
Service in ... km or... days
Resetting Service Interval Display
It is only possible to reset the Service Interval Display, if a service message or at least a
pre-warning is shown on the display of the instrument cluster.
We recommend having this resetting performed by a specialist garage.
The specialist garage:
• resets the memory of the display after the appropriate inspection;
• makes an entry in the Service schedule;
• affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side.
Reset the service interval displays by using the reset button ⇒ page 16 on the trip
counter.
On vehicles which are equipped with information display*, you can call up this information in the following menu on ⇒ page 24:
SETTINGS
Service Interval (Service)
Reset
Caution
We recommend that you do not reset the Service Interval Display yourself otherwise
this can result in the service interval display being incor rectly set, which may also result
in problems with operation of your vehicle.
Note
• Never reset the display between service intervals otherwise this may result in
incorrect readouts.
• information is retained in the Service Interval Display also after the battery of the
vehicle is disconnected.
• If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by a
specialist garage.
• The data displayed is the same after resetting the display with flexible service inter-
vals (QG1) using the reset button as that for a vehicle with fixed service interval s (QG2).
We therefore recommend having the Service Interval Display reset only by an authorised Škoda Service Partner who is familiar with the procedure for resetting the display
with a vehicle system tester.
• Please refer to the brochure Service schedule for extensive information about the
service intervals.
A
3
A
7
sgg.6.book Page 19 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights20
Digital clock
The time is set with the buttons and ⇒ page 16, fig. 15.
Select the display which you wish to change with the button and carry out the
change with the button .
On vehicles which are fitted out with the information display*, it is possible to set the
time in the menu Time ⇒ page 27.
WARNING
The clock should not be adjusted while driving for safety reasons but only when
the vehicle is stationary!
Multi-functional indicator (onboard computer)
Introduction
The multi-functional indicator appears in the display ⇒ fig. 18 or in the information
display ⇒ page 24 depending on the equipment fitted to your vehicle.
The multi-functional indicator offers you a range of useful information.
On vehicles which are fitted out with information display*, it is possible to switch off
the display of some information.
Caution
Pull out the ignition key while having contact with the display (for example when
cleaning) in order to prevent any damage.
Note
• In certai n national versions the displays appear in the Imperial system of measures.
• If the display of the second speed is activated in mph, the current speed* is not
indicated in km/h on the display.
Memory
The multi-functional indicator is equipped with two automatic memories. The
selected memory is displayed in the middle of the display field ⇒ fig. 18.
The data of the single-trip memory (memory 1) is shown if a 1 appears in the display.
A 2 shown in the display means that data relates to the total distance memory
(memory 2).
Switching over the memory with the help of the button ⇒ page 21, fig. 19 on the
windscreen wiper lever or with the help of the button on the multifunction steering
wheel* ⇒ page 21.
The outside temperature ⇒ page 22
Driving time ⇒ page 22
Current fuel consumption ⇒ page 22
Average fuel consumption ⇒ page 22
Range ⇒ page 22
Distance driven ⇒ page 23
Average speed ⇒ page 23
Current speed* ⇒ page 23
Oil temperature ⇒ page 23
Warning against excessive speeds* ⇒ page 23
A3A7A3A
7
Fig. 18 Multi-functional indicator
A
B
A
D
sgg.6.book Page 20 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 21
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment the ignition
is switched on until it is switched off. New data will also flow into the calculation of the
current driving information if the trip is continued within 2 hours after switching off
the ignition. The memory will be is automatically erased, on the other hand, if the trip
is interrupted for more than 2 hours.
Total-trip memory (memory 2)
The total distance driven memory gathers data from any number of individual journeys up to a total of 99 hours and 59 minutes driving or 9.999 kilometres driven. The
memory is deleted when either of these limits is reached and the calculation starts
from anew.
The total-trip memory will not, contrary to the single-trip memory, be deleted after a
period of interruption of driving of 2 hours.
Note
All information in the memory 1 and 2 is erased if the battery of the vehicle is
disconnected.
Operating with the buttons on the windshield wiper lever and on
the multifunction steering wheel*
Fig. 19 Multi-functional indicator: Control elements
The rocker switch and the button are located in the grip of the window wiper
lever ⇒ fig. 19 on the left. Switching over and resetting is performed with the handwheel ⇒ fig. 19 on the multifunction steering wheel.
Selecting the memory
– After briefly pressing the button on the windshield wiper lever or by briefly
pressing the button on the multifunction steering wheel, you can select the
desired memory.
Selecting the functions with the help of the windshield wiper lever
– Press the top or bottom rocker switch for longer than 0.5 seconds. In this way,
call up in sequence the individual functions of the multi-functional indicator.
Selecting the functions with the help of the multifunction steering
wheel
– By pressing the button , you can call up the menu of the multi-functional indi-
cator.
– Turn the handwheel upwards or downwards. In this way, call up in sequence
the individual functions of the multi-functional indicator.
– Short-term pressing of the button allows to select the highlighted function.
Setting function to zero
– Select the memory you want.
– Press the button or for more than 1 second.
The following readouts of the selected memory will be set to zero with the button
on the windshield wiper lever or with the button on the multifunction steering
wheel:
• average fuel consumption,
• distance driven,
• average speed,
• Driving time.
You can only operate the multi-functional indicator when the ignition is switched on.
After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
AAABADABADA
A
ACADA
D
ABA
D
A
B
A
D
sgg.6.book Page 21 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights22
Outside temperature
The outside temperature appears in the display when the ignition is switched on.
If the outside temperature drops below +4°C, a snow flake symbol (warning signal for
ice on the road) appears in front of the temperature indicator and flashes for 10
seconds, then remains displayed together with the outside temperature ⇒ fig. 20. At
the same time an audible signal sounds. After pressing the rocker switch at the
windshield wiper lever ⇒ page 21, fig. 19 or the button at the multifunction
steering wheel ⇒ page 21, fig. 19, the function shown last is indicated.
WARNING
Do not only rely upon the information given on the o utside temperature display
that there is no ice on the road. Please note that black ice may also be present
on the road surface even at temperatures around +4°C - warning, drive with
care!
Driving time
The driving time which has elapsed since the memory was last erased, appears in the
display. If you wish to measure the driving time as of a particular time, you must set the
memory to zero at this moment in time by pressing the button on the windshield
wiper lever ⇒ page 21, fig. 19 or the handwheel on the multifunction steering
wheel* ⇒ page 21, fig. 19 for longer than 1 second.
The maximum distance indicated in both memories is 99 hours and 59 minutes. The
indicator is set back to null if this period is exceeded.
Current consumption
The current fuel consumption level is shown in the display in litres/100 km. This information can help you to adapt your style of driving to the fuel consumption you wish to
achieve.
The display appears in litres/hour if the vehicle is stationary or driving at a low speed.
The indicated value will be updated every 0.5 seconds while you are driving.
Average fuel consumption
The average fuel consumption since the memory was last erased is shown in the
display in litres/100 km ⇒ page 20, fig . 18. This information can help you to adapt your
style of driving to the fuel consumption you wish to achieve.
If you wish to determine the average fuel consumption over a certain period of time
you must set the memory to zero at the start of the measurement using the button
on the windshield wiper lever ⇒ page 21, fig. 19 or with the handwheel on the
multifunction steering wheel* ⇒ page 21, fig. 19. A zero appears in the display for the
first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Note
The amount of fuel consumed will not be indicated.
Range
The estimated range in kilometres is shown on the display. It indicates the distance you
can still drive with your vehicle based on the present level of fuel in the tank for the
same style of driving.
The readout is shown in steps of 10 km. After lighting up of the indicator light for the
fuel reserve the display is shown in steps of 5 km.
The fuel consumption for the last 50 km is taken as a basis for calculating the range. If
you drive in a more economical manner from this moment on, the range will be
increased accordingly.
Fig. 20 The outside temperature
A
A
ACABA
D
A
B
A
D
sgg.6.book Page 22 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 23
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
If the memory is set to zero (after disconnecting the battery), the fuel consumption of
10 ltr./100 km is calculated for the range; afterwards the value is adapted accordingly
to the style of driving.
Distance driven
The distance driven since the memory was last erased appears in the display
⇒ page 20. If you wish to measure the distance driven of a particular time, you must
set the memory to zero at this moment in time by pressing the button on the windshield wiper lever ⇒ page 21, fig. 19 or the handwheel on the multifunction
steering wheel* ⇒ page 21, fig. 19.
The maximum distance indicated in both switch positions is 9.999 km. The indicator is
set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display in
km/hour ⇒ pa ge 20. If you wish to determine the average vehicle speed ov er a certain
period of time you must set the memory to zero at the start of the measurement using
the button on the windshield wiper lever ⇒ page 21, fig. 19 or with the handwheel
on the multifunction steering wheel* ⇒ page 21, fig. 19.
A zero appears in the display for the first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Current speed*
The current speed which is identical to the display of the speedometer, is indicated on
the display ⇒ page 16, fig. 15.
Oil temperature
The oil temperature appears in the display when the ignition is switched on. If there is
a fault, three lines are displayed instead of the temperature.
Warning against excessive speeds*
Fig. 21 Warning against excessive speeds / multi-functional indicator: Control elements
This function enables you to set a speed limit, e.g. if you drive in town. A text in the
display is intended to draw your attention to the fact that you have exceeded the set
speed limit.
Warning against excessive speeds
– Select the menu point Speed warning --- km/h (warning at --- km/h)..
– Drive e.°g at a speed of 50 km/h.
– Press the button on the windshield wiper lever ⇒ fig. 21 or the handwheel
on the multifunction steering wheel* ⇒ page 21, fig. 19. Speed warning 50 km/h
(warning at 50 km/h) is displayed in the information display* ⇒ fig. 21. You can
increase or reduce this value with the button on the windshield wiper lever or
by turning the handwheel on the multifunction steering wheel*.
– The value is stored by repeated pressing of the button on the windshield wiper
lever or the handwheel on the multifunction steering wheel*.
If you now exceed the set speed limit, Speed 50°km/h exceeded will be shown on the
display. This message is indicated for as long as the speed is reduced below the set
limit or switch off the message by pressing the button on the windshield wiper lever
⇒ fig. 21 or the handwheel on the multifunction steering wheel* ⇒ page 21,
fig. 19.
An audible signal sounds as an additional warning signal.
The set speed limit remains stored even after switching off the ignition.
A
B
A
D
A
B
A
D
A
2
ABADAAADA
B
ADA
B
A
D
sgg.6.book Page 23 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights24
Information display*
Introduction
The information display provides you with information in a convenient way
concerning the current operating state of your vehicle. The information system also
provides you with data (depending on the equipment installed in the vehicle) relating
to the radio, mobile phone, multi-functional indicator, navigation system, the unit
connected to the MDI input and the automatic gearbox.
Certain functions and operating conditions are always being checked on the vehicle
when the ignition is switched on and also while driving.
Functional faults, if required repair work and other information are indicated by red
symbols ⇒ page 26 and yellow symbols ⇒ page 27.
Lighting up of certain symbols is combined with an acoustic warning signal.
Information and texts giving warnings are also shown in the display ⇒ page 29.
The display of text is possible in the following languages:
Czech, English, German, French, Italian, Spanish, Portuguese, Russian and Chinese.
You can select the desired language in the setting menu.
The following information can be shown in the display (depending on the equipment
installed on the vehicle):
Caution
Pull out the ignition key while having contact with the display (for example when
cleaning) in order to prevent any damage.
Main menu
Fig. 23 Information display: Controls on the windshield wiper lever / controls on the multifunction steering wheel
Operating with the buttons on the windshield wiper lever
– You can activate the MAIN MENU by pressing the rocker switch ⇒ fig. 23 for
more than 1 second.
– You can select individual menu points by means of the rocker switch . When the
pushbutton is briefly pressed, the information you have selected is displayed.
Operating with the buttons on the multifunction steering wheel*
– You can call up the MAIN MENU by pressing the button ⇒ fig. 23.
Fig. 22 Instrument cluster: Information
display
Main menu ⇒ page 24
Door, luggage compartment door and bonnet ajar warning
⇒ page 25
Service Interval Display ⇒ page 18
Selector lever positions for the automatic gearbox DSG ⇒ page 122
AAAAA
B
A
C
sgg.6.book Page 24 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 25
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– You can select the individual menus by pressing the handwheel . After briefly
pressing the handwheel , the desired menu is indicated.
– After briefly pressing the button you can achieve a higher level, by pressing the
button for longer than 1 second, you can call up the MAIN MENU.
You can select the following information (depending on the equipment installed on
the vehicle):
MFD (Onboard computer) ⇒ page 20
Audio*
Navigation*
Phone* ⇒ page 129
Aux. Heating (auxiliary heating)* ⇒ page 105
Assistant* ⇒ page 55
Vehicle status ⇒ page 26
Setup ⇒ page 27
The menu point Audio is only then displayed when the factory-fitted Radio* is
switched on.
The menu point Navigation is only then displayed when the factory-fitted Navigation
system* is switched on.
The menu point Aux. Heating is only then displayed, if the vehicle is fitted with the
factory-fitted auxiliary heating*.
The menu point Assistant is only then displayed, if the vehicle is fitted with cornering
lights*.
Note
• If warning messages are shown in the information display ⇒ page 25 ⇒ page 26,
these messages can be confirmed with the button on the windshield wiper lever or
with the button on the multifunction steering wheel in order to call up the main
menu.
• If you do not activate the information display at that moment, the menu shifts to
one level higher every 10 seconds.
• The operation of the factory-fitted radio* or the navigation system* is described in
separate operating instructions to be found in the on-board literature.
Door, luggage compartment door and bonnet ajar warning
The door, luggage compartment and bonnet ajar warning lights up if at least one door,
the luggage compartment or bonnet are not closed. The symbol indicates which door
is still open or whether the luggage compartment door or bonnet is not closed
⇒ fig. 24.
The symbol goes out as soon as the doors, luggage compartment d oor and bonnet are
completely closed.
A warning signal sounds if the car is driven at a speed of more than 6km/hour and if
the engine or the luggage compartment door is open.
ADADACACA
B
A
D
Fig. 24 Information display: Door
warning
sgg.6.book Page 25 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights26
Auto Check Control*
Car state
The Auto Check Control carries out a check of certain functions and vehicle components. The check is performed constantly when the ignition is switched on, both when
the vehicle is stationary, as well as when driving.
Some operational faults, urgent repairs, service work or other information appear in
the display of the instrument cluster. The displays are shown with a red or yellow light
symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indicate a
warning (priority 2). Information for the driver may also appear in addition to the
symbols ⇒ page 29.
Shown in the menu Vehic le s tatu s, if there is at least one error message. After selecting
this menu the first of the error messages is displayed. Several error messages are
shown on the display under the message e.°g. 1/3 ⇒ fig. 25. This indicates that the first
of a total of three error messages is displayed. The respective messages are displayed
one after the other in an interval of 5 se conds. Check as soon as possible the displayed
error messages.
As long as the operational faults are not rectified, the symbols are always indicated
again. After the first display, the symbols are indicated without information for the
driver.
If a fault occurs, a warning signal will also sound in addition to the symbol and text in
the display:
• Priority 1 - three warning signals
• Priority 2 - one warning signal
Red symbols
A red symbol signals danger.
– Bring the vehicle to a stop.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
Three successive warning signals will sound if a red symbol appears.
Fig. 25 Information display: Display of
operational fault
Engine oil pressure too low ⇒ page 33
Overheated clutches of the automatic gearbox DSG*
⇒ page 38
Fig. 26 Information display: Oil pressure
is low
sgg.6.book Page 26 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 27
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Yellow symbols
A yellow symbol signals a warning.
Check the relevant function as soon as possible.
The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.
Set-up
You can change certain settings by means of the information display. The current
setting is shown on the information display in the respective menu at the top below the
line ⇒ fig. 28.
You can select the following information (depending on the equipment installed on
the vehicle):
• Language
• MFD Data (MFA DATA)
• Convenience
• Lights & Vision (Lights & Vision)
• Time
• Winter tyres
• Units
• Assistant (Assistant)
• Alternative speed displayed (Second speed)
• Trave l mode
• Service Interval (Service)
• Factory Setting
• Back
After selecting the menu point Back you will reach one level higher in the menu.
Check engine oil level,
engine oil sensor faulty
⇒ page 205
Brake pad worn ⇒ page 36
Fig. 27 Information display: Brake pad
worn
Fig. 28 Setting the clock
sgg.6.book Page 27 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights28
Language
Here you can set in which language the warning and information texts should be
displayed.
Displays of the MFA
Here you can switch off or on certain displays of the multi-functional indicator.
Comfort*
You can set the following functions (depending on the equipment installed on the
vehicle):
Lights and Visibility
Here you can set how long the light should stay on for the function Coming/Leaving
Home. Furthermore you can here switch on or off the function daylight driving lights
and convenience turn signal.
After selecting the menu point Factory setting the factory setting of the lighting is
established again.
Time
Here you can set the time, the time format (12 or 24 hour indicator) and the time
change summer/winter time.
Winter tyres
Here you can set at which speed a warning signal should sound. This function is used
for e.g winter tyres with the permissible maximum speed less than the maximum
speed of the vehicle.
When exceeding the speed, the following is displayed on the information display*:
Snow tyres max. speed ... km/h (Winter tyres maximum ... km/h)
Measures
Here you can set the units for temperature, consumption and distance driven.
Assistant
Here you can adjust the tones of the acoustic signals of the parking aid*.
Second speed
Here you can switch on the display of the second speed in mph or in km/h2).
Tra vel mode
Here you can activate / deactivate the mode “tourist light”. This mode makes it possible
to drive in countries with opposing traffic system, driving on the left/right, without
dazzling the oncoming vehicles. The headlight swivel function is deactivated when
switching on this mode. Further information ⇒ page 56.
Rain closing
On vehicles with rain sensor you can switch on or off the
function for automatic closing of the windows and the
sliding/tilting roof in case of rain and locked vehicle. If it is
not raining and the function is set, the windows including
the sliding/tilting roof are closed automatically after
approx. 12 hours.
Door open Here you can switch on or off the functions for opening a
single door and automatic closing.
ATA con firm
Here you can set if a signal tone should sound additionally
when activating or deactivating the anti-theft alarm system.
Window op. Here you can set the convenience mode only for the driver
window or for all the windows.
Mirror down
Here you can switch on or off the function for mirror lowering on the front passenger side when engaging the
reverse gear a).
Mirror adjust. Here you can switch on or off the function for left and right
exterior mirror adjustment simultaneously.
Factory sett ing
After selecting this menu the convenience setting is reset
to factory setting. The following is displayed in the information display:
Factory setting for convenience is set
a)
This function is only available on vehicles with an electrically adjustable driver seat.
2)
Valid for countries where the values are indicated in British measuring units.
sgg.6.book Page 28 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 29
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Service
Here you can have the kilometers still to be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting
After selecting the menu point Factory Setting the factory setting of the information
display is established again.
Warning lights
Overview
The warning lights indicate certain functions or faults.
Fig. 29 Instrument cluster with warning lights
Turn signal lights (to the left) ⇒ page 31
Turn signal lights (to the right) ⇒ page 31
Fog lights* ⇒ page 31
Main beam light ⇒ page 31
Low beam light ⇒ page 31
Rear fog light ⇒ page 31
Speed regulating system* ⇒ page 31
sgg.6.book Page 29 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights30
WARNING
• If you do not pay attention to the warning lights coming on and the corre-
sponding descriptions and warning notes, this may result in severe body injuries or major vehicle damage.
• The engine compartment of your car is a hazardous area. There is a risk of
injuries, scalding, accidents and fire when working in the engine compartment,
e.g. inspecting and replenishing oil and other fluids. It is also essential to
observe all warnings ⇒ page 204, “Working in the engine compartment”.
Note
• The arrangement of the indicator lights depends on the model version. The
symbols shown in the following functional description are to be found as indicator
lights in the instrument cluster.
• Operational faults are shown in the instrument cluster as red symbols (priority 1 -
danger) or yellow symbols (priority 2 - warning).
Failure of the light bulbs ⇒ page 31
Diesel particle filter* (diesel engine) ⇒ page 31
Airbag system ⇒ page 32
Control system for exhaust ⇒ page 32
Electromechanical power steering ⇒ page 32
Engine oil level ⇒ page 33
Engine oil pressure ⇒ page 33
EPC fault light (petrol engine) ⇒ page 33
Glow plug system (diesel engine) ⇒ page 34
Coolant temperature/coolant level ⇒ page 34
Traction control system (TCS) ⇒ page 34
Electronic stability programme (ESP)* ⇒ page 35
Selector lever lock* ⇒ page 35
Tyre pressure* ⇒ page 35
Antilock brake system (ABS) ⇒ page 36
Boot lid ⇒ page 37
Open door ⇒ page 37
Seat belt warning light ⇒ page 36
Brake pad wear* ⇒ page 36
Fluid level in windshield washer system* ⇒ page 37
Brake system ⇒ page 37
Dynamo ⇒ page 37
Fuel reserve ⇒ page 38
Downhill Drive Support* ⇒ page 38
Overheated clutches of the automatic gearbox
DSG*
⇒ page 38
sgg.6.book Page 30 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 31
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Turn signal system
Either the left or right indicator light flashes depending on the position of the turn
signal lever.
The indicator light flashes at twice its normal rate if a turn signal light fails. This does
not apply when towing a trailer.
Switching off the hazard warning light system is switched on will cause all of the turn
signal lights as well as both indicator lights to flash.
Further information about the turn signal system ⇒ page 59.
Fog lights*
The warning light comes on when the fog lights are operating ⇒ page 56.
Main beam
The indicator light comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam ⇒ page 59.
Low beam
The warning light comes on when low beam is selected ⇒ page 53.
Rear fog light
The warning light comes on when the rear fog lights are operating ⇒ page 57.
Cruise control system*
The warning light lights up, when operating the speed regulating system.
Bulb failure
The warning light comes on if a bulb is faulty:
• up to 2 seconds after the ignition is switched on;
• when switching on the defective light bulb.
The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The indicator light only lights up if all light bulbs of the licence plate lighting or the parking
light (in one rear light unit) are defective. Check regularly the function of the light
bulbs.
Diesel particle filter* (diesel engine)
If the warning light comes on, this means that soot has accumulated in the diesel
particle filter because of the frequent short distances.
In order to clean the diesel particle filter, the vehicle should be dr iven at an even speed
of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 15 minutes or until
the warning light goes out with the 4th or 5th gear engaged (automatic gearbox: position S) when the traffic situation permits it. This increases the exhaust temperature and
the soot deposited in the diesel particle filter is burnt.
Always pay attention to the valid speed limits ⇒ .
The warning light goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly cleaned, the warning light does not go out and the
warning light begins to flash. In the information display* appears Diesel-particle
Owner's manual. Afterwards the engine control unit shifts the engine into the emergency mode, which only has a reduced power output. After switching the ignition off
and on again the warning light comes on.
Have the vehicle inspected without delay by your specialist garage.
sgg.6.book Page 31 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights32
WARNING
• If you do not pay attention to the warning light coming on and the corre-
sponding descriptions and warning notes, this may result in injuries or major
vehicle damage.
• Always adjust your speed to suit weather, road, region and traffic condi-
tions. The route indicated by the warning light must not tempt you to disregard
the national regulations for road traffic.
Caution
As long as the warning light li ght s up, one m ust take into acco unt an in crea sed f uel
consumption and in certain circumstances a power reduction of the engine.
Note
Further information about diesel particle filter ⇒ page 170.
Airbag system
Monitoring the airbag system
The warning light comes on for a few seconds when the ignition is switched on.
There is a fault in the system if the warning light does not go out or flashes while driving
⇒ . This also applies if the warning light does not come on when the ignition is
switched on.
The following text will be displayed in the information display*:
Airbag fault!
The functionality of the airbag system is also monitored electronically when one airbag
has been switched off.
Front, side and head airbags or belt tensioner which have been switched off
using the vehicle system tester:
• The warning light lights up for 4 seconds after switching on the ignition and then
flashes again for 12 seconds in intervals of 2 seconds.
The following text will be displayed in the information display*:
Airbag/belt tensioner deactivated!
If the airbag was switched off using the airbag switch* in the stowage compartment on the front passenger side:
• The warning light comes on for 4 seconds after the ignition has been switched
on.
• switching off the airbag is indicated in the middle of the dash panel by the lighting
up of the yellow indicator light in display ⇒ page 154.
WARNING
Have the airbag system checked immediately by a specialist garage if a fault
exists. Otherwise, there is a risk of the airbag not being activated in the event of
an accident.
Control system for exhaust
The warning light comes on after the ignition has been switched on.
If the warning light does not go out after starting the engine or it lights up when driv ing,
a fault exists in an exhaust relevant component. The engine management system
selects an emergency programme which enables you to drive to the nearest specialist
garage by adopting a gentle style of driving.
Electromechanical power steering
The warning light comes on for a few seconds when the ignition is switched on.
If the warning light after switching on the ignition or when driving lights up continuously, a fault exists in the electromechanical power steering.
• If the yellow warning light lights up , this indicates a partial failure of the power
steering and the steering assist can be reduced.
• If the re d warning light lights up , this indicates a complete failure of the power
steering and the steering assist has failed.
Further information ⇒ page 168.
sgg.6.book Page 32 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 33
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
WARNING
Contact your specialist garage if the power steering is defective.
Note
• If the yellow warning light goes out after starting the engine again and a short
drive, it is not necessary to visit a specialist garage.
• If the battery has been disconnected and reconnected, the yellow warning light
comes on after switching on the ignition. The warning light must go out after driving a
short distance.
Engine oil pressure
The warning light comes on for a few seconds 3) when the ignition is switched on.
Stop the vehicle and switch the engine off if the warning light does not go off after
the engine has started or flashes while driving. Check the oil level and top up with oil
as necessary ⇒ page 206, “Replenishing engine oil”.
An audible signal sounds three times as an additional warning signal.
Do not continue your journey if for some reason it is not possible under the conditions prevailing to top up with oil. Keep the engine switched off and obtain profes-
sional assistance from a specialist garage, otherwise it could lead to severe engine
damage.
Do not drive any further if the warning light flashes even if the oil is at the correct
level. Do not run the engine not at idling speed either. Contact the nearest specialist
garage to obtain professional assistance.
The following text will be displayed in the information display*:
Oil Pressure Engine off! Owner's manual!
WARNING
• If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch off the engine and switch on the hazard
warning light system.
• The red oil pressure light is not an oil level indicator! One should there-
fore check the oil level at regular intervals, preferably after every refueling
stop.
Engine oil level
Warning light lights up
If the warning light lights up, the quantity of oil in the engine is probably too low.
Check as soon as possible the oil level or top up ⇒ page 206 with engine oil.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
Check oil level!
The warning light will go out if the bonnet is left open for more than 30 seconds. If no
engine oil has been replenished, the warning light will come on again after driving
about 100 km.
Warning light flashes
A fault on the engine oil level sensor is indicated additionally by an audible signal and
the warning light coming on several times after the ignition has been switched on.
In this case have the engine inspected without delay by a specialist garage.
The following text will be displayed in the information display*:
Oil sensor Workshop!
EPC fault light (petrol engine)
The (Electronic Power Control) warning light comes on for a few seconds when the
ignition is switched on.
3)
The warning light on vehicles fitted with information display does not come on after switching the ignition on, but only if a fault exists or the engine oil level is too low.
sgg.6.book Page 33 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights34
If the warning light does not go out or lights up after starting the engine, a fault
exists in the engine control. The engine management system selects an emergency
programme which enables you to drive to the nearest specialist garage by adopting a
gentle style of driving.
The following text will be displayed in the information display*:
Engine fault Workshop!
Glow plug system (diesel engine)
The warning light lights up for a cold engine when switching on the ignition (preheat position) 2 ⇒ page 109. Start the engine after the indicator light goes out.
The glow plug indicator light will come on for about 1 second if the engine is at a
normal operating temperature or if the outside temperature is above +5°C. This
means that you can start the engine right away.
There is a fault in the glow plug system if the warning light does not come on or
lights up continuously; contact a specialist garage as soon as possible to obtain
assistance.
If the warning light begins to flash while driving, a fault exists in the engine
control. The engine management system selects an emergency programme which
enables you to drive to the nearest specialist garage by adopting a gentle style of
driving.
The following text will be displayed in the information display*:
Engine fault Workshop!
Coolant temperature/ Coolant quantity
The warning light comes on for a few seconds 4) when the ignition is switched on.
The coolant temperature is too high or the coolant level too low if the warning light
does not go out or flashes while driving.
3 peeps sound as an additional warning signal.
In this case stop and switch the engine off and check the coolant level; top up the
coolant as necessary.
Do not continue your journey if for some reason it is not possible under the conditions prevailing to top up with coolant. Keep the engine switched off and obtain
professional assistance from a specialist garage, otherwise it could lead to severe
engine damage.
If the coolant is within the specified range, the increased temperature may be caused
by an operating problem at the coolant fan. Check the fuse for the coolant fan, replace
it if necessary ⇒ page 234, “Fuse assignment in engine compartment - version 1” or
⇒ page 236, “Fuse assignment in engine compartment - version 2”.
Do not continue driving if the warning light does not go off al though the fluid is at the
correct level and also the fuse of the fan is in proper order. Contact a specialist garage
to obtain assistance.
Please also refer to the additional instructions ⇒ page 207, “Cooling system”.
The following text will be displayed in the information display*:
Check coolant! Owner's manual
WARNING
• If you must stop for technical reasons, then park the vehicle at a safe
distance from the traffic and switch off the engine and switch on the hazard
warning light system ⇒ page 58.
• Take care when opening the coolant expansion bottle. If the engine is hot,
the cooling system is pressurized - risk of scalding! It is best to allow the engine
to cool down before removing the cap.
• Do not touch the coolant fan The coolant fan may switch on automatically
even if the ignition is off.
Traction control system (TCS)
The warning light comes on for a few seconds when the ignition is switched on.
The warning light flashes quickly when a control cycle is activated while driving.
The warning light flashes slowly if the TCS system is switched off.
4)
The warning light on vehicles fitted with information display does not come on after switching
the ignition on, but only if the coolant temperature is too high or the coolant level is too low.
sgg.6.book Page 34 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 35
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The warning light lights up permanently if there is a fault in the TCS system.
The fact that the TCS system operates together with the ABS means that the TCS
warning light will also come on if the ABS system is not operating properly.
If the warning light
comes on immediately after starting the engine, the TCS system
can be switched off for technical reasons. In this case, the TCS system can be switched
on again by switching the ignition on and off. If the warning light goes out, the TCS
system is fully functional again.
Further information about the TCS ⇒ page 165, “Traction control system (TCS)”.
Note
If the battery has been disconnected and reconnected, the warning light comes on
after switching on the ignition. The warning light must go out after driving a short
distance.
Electronic stability programme (ESP)*
The warning light comes on for a few seconds when the ignition is switched on.
When the ESP helps to stabilise the vehicle (for example when applying and releasing
a braking force to an individual wheel), then the warning light flashes quickly in the
information display.
The ESP system cannot be switched off, the TCS system can only be switched off by
pressing the button ⇒ page 163, fig. 154, then the warning light flashes slowly .
The warning light lights up permanently if there is a fault in the ESP system.
The fact that the ESP system operates together with the ABS means that the ESP
warning light will also come on if the ABS system is not operating properly.
If the warning light comes on immediately after star ting the engine, the ESP system
can be switched off for technical reasons. In this case, the ESP system can be switched
on again by switching the ignition on and off. If the warning light goes out, the ESP
system is fully functional again.
Further information on the ESP ⇒ page 163, “Electronic stability programme (ESP)*”.
Electronic Differential Lock (EDL)*
The EDL is a part of the ESP. A fault in the EDL is indicated by the ESP warning light in
the instrument cluster. Have the vehicle inspected immediately by your specialist
garage. Further information on the EDL ⇒ page 164, “Electronic Differential Lock
(EDL)*”.
Note
If the battery has been disconnected and reconnected, the warning light comes on
after switching on the ignition. The warning light must go out after driving a short
distance.
Selector lever lock*
If the green warning light lights up, operate the brake pedal. This is necessary, in
order to be able to move the selector lever out of the position P or N.
Further information about the selector lever lock ⇒ page 123.
Tyre inflation pressure*
The warning light lights up, if there is a substantial drop in inflation pressure in one
of the tyres. Reduce the speed and check or correct as soon as possible the inflation
pressure in the tyres ⇒ page 215.
If the warning light flashes, there is a system fault. Visit the nearest specialist garage and
have the fault rectified.
Further information about tyre pressure-control system ⇒ page 169.
WARNING
• When the warning light lights up, immediately reduce the speed and
avoid sudden steering and brake manoeuvres. Please stop the vehicle without
delay at the nearest possible stop and inspect the tyres and their inflation pressures.
• Under cer tain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light can be delayed or does not light up at all.
sgg.6.book Page 35 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights36
Note
If the battery has been disconnected, the warning light comes on after switching on
the ignition. The warning light must go out after driving a short distance.
Antilock brake system (ABS)
The warning light shows the functionality of the ABS.
The warning light comes on for a few seconds after the ignition has been switched on
or when starting the engine. The warning light goes out after an automatic check
sequence has been completed.
A fault in the ABS
The system is not functioning properly if the ABS warning light does not go out
within a few seconds after switching on the ignition, does not light up at all or lights up
while driving. The vehicle will only be braked by the normal brake system. Visit a
specialist garage as quickly as possible and adjust your style of driving appropriately as
you will not know how great the damage is.
Further information about ABS ⇒ page 167, “Antilock brake system (ABS)”.
A fault in the entire brake system
If the ABS warning light comes on together with the brake system warning light
(handbrake must be released), there is a fault not only in the ABS but also in another
part of the brake system ⇒ .
WARNING
• If the brake system warning light comes on together with the ABS
warning light stop the vehicle immediately and check the brake fluid level in
the reservoir ⇒ page 209, “Brake fluid”. If the fluid level has dropped below the
MIN marking, do not drive any further - risk of accident! Obtain professional
assistance.
• Pay attention to the following instructions before checking the brake fluid
level and opening the bonnet ⇒ page 204, “Working in the engine compartment”.
• If the brake fluid is at the correct level, the ABS control function has failed.
The rear wheels may then block very rapidly when braking. In certain circumstances, this can result in the rear end of the car breaking away - risk of skidding! Drive carefully to the nearest specialist garage and have the fault
rectified.
Seat belt warning light
The warning light comes on after the ignition is switched on as a reminder for the
driver and front passenger to fasten the seat be lt. The warning light only goes out if the
driver or front passenger has fastened his seat belt.
If the seat belt has not been fastened by the driver or front passenger, a permanent
warning signal sounds at vehicle speeds greater than 20 km/h and simultaneously the
warning light flashes.
If the seat belt is not fastened by the driver or front passenger during the next 90
seconds, the warning signal is deactivated and the warning light lights up permanently.
Further information on the seat belts ⇒ page 141, “Seat belts”.
Thickness of the brake pads*
The warning light comes on for a few seconds 5) when the ignition is switched on.
If the warning light comes on, contact a specialist garage immediately and have the
brake pads on all of the wheels inspected.
The following text will be displayed in the information display*:
Check brake pads!
5)
The warning light on vehicles fitted with information display does not come on after switching
the ignition on, but only if a fault exists.
WARNIN G (continued )
sgg.6.book Page 36 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights 37
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Boot lid
The warning light comes on when the ignition is switched on if the luggage
compartment door is open. If the boot lid opens while driving , the warning light
lights up and an audible signal sounds.
An audible signal sounds as an additional warning signal.
The warning light comes on even when the ignition is switched off. The warning light
lights up for a maximum of 5 minutes.
On vehicles with information display* this warning light is replaced by a vehicle symbol
⇒ page 25.
Open door
The warning light comes on, if one or several doors are opened. If one of the doors
opens while driving, the warning light lights up and an audible signal sounds.
The warning light comes on even when the ignition is switched off. The warning light
lights up for a maximum of 5 minutes.
On vehicles with information display* this warning light is replaced by a vehicle symbol
⇒ page 25.
Windshield washer fluid level*
The warning light comes on when the ignition is switched on if there is insufficient
fluid in the windshield washer system. Top up with liquid ⇒ page214.
The following text will be displayed in the information display*:
Add wash fluid!
Brake system
The warning light flashes or comes on if the brake fluid level is too low, if there is a
fault in the ABS or if the handbrake is applied.
If the warning light flashes and an audible signal sounds three times (handbrake is
not applied), stop and check the brake fluid level ⇒ .
The following text will be displayed in the information display*:
Brake fluid Owner's manual
If there is a fault in the ABS which also influences the function of the brake system (e.g.
distribution of brake pressure), the ABS warning light comes on and at the same
time the brake system warning light starts flashing . Be aware that not only the ABS
but also another part of th brake system is defective ⇒ .
An audible signal sounds three times as an additional warning signal.
One should get used to high pedal forces, long braking distances and long free play of
the brake pedal when driving to the next specialist garage.
For further information on the brake system ⇒ page 166, “Brakes”.
Handbrake applied
The warning light also comes on if the handbrake is applied. An audible warning is
also given if you drive the vehicle for at least 3 seconds at a speed of more than 6 km/h.
The following text will be displayed in the information display*:
Release parking brake!
WARNING
• Pay attention to the following instructions before checking the brake fluid
level and opening the bonnet ⇒ page 204, “Working in the engine compartment”.
• If the brake system warning light does not go out a few seconds after
switching on the ignition or comes on when driving, stop immediately and
check the brake fluid in the reservoir ⇒ page 209. If the fluid level has dropped
below the MIN marking, do not drive any further - risk of accident! Obtain
professional assistance.
Alternator
The warning light comes on after the ignition has been switched on. It should go
out after the engine has started.
sgg.6.book Page 37 Thursday, September 24, 2009 2:32 PM
Instruments and Indicator/Warning Lights38
If the warning light does not go out after the engine has started, or comes on when
driving, drive to the nearest specialist garage. The vehicle battery will be discharged in
this case so switch off all non-essential electrical components.
Caution
If the warning light comes on when driving and in addition the warning light
(cooling system fault) also comes on in display, you must then stop the car immediately and switch the engine off - risk of engine damage!
Fuel reserve
The warning light comes on, if the fuel level is still below 10.5 litres.
An audible signal sounds as an additional warning signal.
The following text will be displayed in the information display*:
Please refuel! Range...km
Note
The Text in the information display* goes out only after refuelling and driving a short
distance.
Downhill Drive Support*
The warning light comes on for a few seconds when the ignition is switched on.
The warning light comes on when the speed of the car is less than 30 km/h and after
pressing the Offroad button ⇒ page 170.
The warning light flashes when the Downhill Drive Support actively intervenes.
If your vehicle exceeds the speed of 30 km/h, the Downhill Drive Support is deactivated. The warning light goes out. If the speed is subsequently reduced below 30 km/h,
the Downhill Drive Support is activated. The warning light comes on.
The Downhill Drive Support is activated again when the engine is switched off and the
car is restarted within 30 seconds.
The Downhill Drive Support is deactivated after switching off the ignition.
In the event of a fault, the warning light does not come on when the speed of the car is
less than 30 km/h and after pressing the Offroad button.
Further information about the Offroad system ⇒ page 170, “Off-road*”.
Temperature control of the automatic gearbox DSG*
The warning light lights up if the temperature of the clutches of the automatic
gearbox DSG is too high.
An audible signal sounds as an additional warning signal.
The following text will be displayed in the information display*:
Gearbox overheated: Stop! Owner's man.!
Caution
In the event that the clutches of the automatic gearbox DSG overheat, the warning light
and a warning appear in the information display*. In such a case bring the vehicle
to a stop and switch off the engine. You must wait until the warning light and the
warning go out - risk of gearbox damage! You can continue the trip as soon as the
warning light and the warning go out.
sgg.6.book Page 38 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 39
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Unlocking and locking
Key
Fig. 30 Set of keys without remote control / set of keys with remote control key
Two keys are provided with the vehicle. Dependi ng on the equipment, your vehicle can
be equipped with keys without radio remote control or with radio remote control keys*
⇒ fig. 30.
WARNING
• Always withdraw the key whenever you leave the vehicle - even if it is only
for a short time. This is particularly important if children are left in the vehicle.
The children might otherwise start the engine or operate electrical equipment
(e.g. power windows) - risk of injury!
• Do not withdraw the ignition key from the ignition lock until the vehi cle has
come to a stop. The steering lock might otherwise engage unintentionally - risk
of accident!
Caution
• Each key contains electronic components; therefore protect them against moisture
and severe shocks.
• Keep the groove of the keys absolutely clean as impurities (textile fibres, dust etc.)
have a negative effect on the proper operation of the locking cylinder and the ignition
lock.
Note
Please approach a specialist garage if you lose a key since he can obtain a new one for
you.
Changing the battery of the radio remote control
Fig. 3 1 Remote control key - remove c over / remo ve batter y
Each remote control key contains a battery which is housed under the cover
⇒ fig. 31. If the battery is discharged, the red indicator light does not light up after
pressing a button on the remote control ⇒ fig. 30. Change the battery as follows:
– Fold open the key.
– Carefully press off the cover at the points of the arrows .
– Remove the discharged battery from the key by pressing the battery dow nwards at
the point of the arrow ⇒ fig. 31.
– Insert the new battery. Ensure that the “+” symbol on the battery is facing upwards.
The correct polarity is shown on the battery cover.
– Position the battery cover on the key and press on it until it is heard to lock in pla ce.
For the sake of the environment
Dispose of an old battery in accordance with environmental regulations.
ABAAA1A
2
sgg.6.book Page 39 Thursday, September 24, 2009 2:32 PM
Unlocking and locking40
Note
• Pay attention to the correct polarity when changing the battery.
• The replacement battery must have the same specification as the original battery.
• If it is still not be possible to unlock or lock the vehicle with the remote control even
after replacing the battery this means that the system has to be synchronised
⇒ page 46.
Electronic immobiliser
The electronic immobiliser prevents the vehicle being operated by an
unauthorised person.
An electronic chip is integrated in the head of the key. The immobiliser is deactivated
with the aid of this chip when the key is inserted in the ignition lock. The electronic
immobiliser is automatically activated when you withdraw the ignition key from the
lock.
Note
It is only possible to start the engine of your car with a Genuine Škoda key with the
matching code.
Child safety lock
The child safety lock prevents the rear door from being opened from the
inside.
The rear doors are equipped with a child safety lock. You can switch the child safety
lock on and off using the vehicle key.
Switching child safety lock on
– Use the vehicle key to turn the slit in the rear door to the left in the direction of the
arrow ⇒ fig. 32.
Switching child safety lock off
– Use the vehicle key to turn the slit to the right against the direction of the arrow.
So long as the child safety lock is switched on it is not possible to open the door from
the inside with the door opening lever. In this case the door can be opened only from
the outside.
Central locking system
Description
Unlocking or locking causes all the doors and the fuel filler flap* to be unlocked or
locked at the same time by the central locking system (as long as it is not set differently
in the menu Setup (settings) - Convenience information display*). The boot lid is
unlocked when opening. It can be opened by pressing the hand grip above the licence
plate ⇒ page 44.
Operation of the central locking system is possible:
• from the outside using the vehicle key ⇒ page 42,
• using the button for the central locking system ⇒ page 43,
• by using the remote control ⇒ page 45.
Indicator light in the driver's door on vehicles without anti-theft alarm system
After the car is locked, the indicator light flashes after 2 seconds.
After the car is locked with the deactivated safe securing system, the indicator light
flashes only after 30 seconds.
Fig. 32 Child safety locks on the rear
doors
sgg.6.book Page 40 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 41
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Indicator light in the driver's door on vehicles with anti-theft alarm system
After locking the vehicle the indicator light flashes for 2 seconds fast, then more slowly.
If the vehicle is locked and the safe securing system ⇒ page 41 is not operating, the
indicator light in the driver door flashes for about 2 seconds fast, goes out and starts to
flash slowly after about 30 seconds.
If the indicator light first of all flashes fast for about 2 seconds, afterwards lights up for
about 30 seconds and then flashes slowly, there is a fault in the system of the central
locking or the interior monitor* ⇒ page 47. Visit a specialist garage to obtain assistance.
Convenience operation of windows
One can open and close the electrically powered windows when unlocking and
locking the vehicle ⇒ page 49.
Opening a single door*
This function makes it possible to only unlock the driver's door. The other doors and
the fuel filler flap* remain locked and are only unlocked after repetitive unlocking.
If you wish, you can have a specialist garage activate the function of the single door
opening mode or you can activate it yourself in the menu of the information display*
⇒ page 24.
Automatic locking*
All the doors and the boot lid are locked automatically once the car reaches a speed of
about 15 km/h.
If the ignition key is withdrawn, the car is then automatically unlocked again. In addition, it is possible for the driver to unlock the car by pressing the central locking button
⇒ page 40 or by pulling the door opening lever.
If you wish, you can have a specialist garage activate the function of the single door
opening mode or you can activate it yourself in the menu of the information display*
⇒ page 24.
WARNING
Locking the doors prevents involuntary opening in an exceptional situation (an
accident). Locked doors prevent unwanted entry into the vehicle from outside,
for example at road crossings. Locked doors do, however, make it more difficult
for rescuers to get into the vehicle in an emergency - danger to life!
Note
• In the event of an accident in which the airbags are deployed, the locked doors are
automatically unlocked in order to enable rescuers to gain access to the vehicle.
• Only the front doors can be unlocked and locked using the key if the central locking
system fails. You can lock or unlock manually the other doors and the boot lid.
− Emergency locking of the door ⇒ page 43.
− Emergency unlocking of the boot lid ⇒ page 44.
Safe securing
The central locking system is equipped with a safe securing6) system. Locking the
vehicle from the outside causes the door locks to be automatically blocked. It is not
possible to open the doors with the door handle either from the inside or from the
outside. This acts as an effective deterrent for attempts to break into your vehicle.
You can deactivate the safe securing system by locking twice within 2°seconds.
If the safe securing system is not operating, the warning light in the driver door flashes
for about 2 seconds fast, goes out and starts to flash slowly again after about
30°seconds.
The safe securing system is again activated the next time the vehicle is unlocked and
locked again.
If the vehicle is locked and the safe securing system is deactivated, you can open the
vehicle from the inside by pulling on the door opening lever. The door is unlocked and
opened at the same time.
6)
Only valid for some countries.
WARNIN G (continued )
sgg.6.book Page 41 Thursday, September 24, 2009 2:32 PM
Unlocking and locking42
WARNING
If the vehicle is locked from the outside and the safe securing system is activated, there must not be any person and animals in the vehicle as it is then not
possible to open either a door or a window from the inside. The locked doors
make it more difficult for rescuers to get into the vehicle in an emergency,
hazard!
Note
The anti-theft alarm system* is also activated with the deactivated safe securing
system when locking the vehicle. The interior monitor* is however not activated.
Unlocking the vehicle using the key
– Turn the key in the locking cylinder of the driver's door in the direction of travel
(unlock position) ⇒ fig. 33.
– Pull on the door handle and open the door.
• All the doors (only the driver's door on vehicles with anti-theft alarm system) and
the fuel filler flap* are unlocked.
• The boot lid is then unlocked.
• The switched on interior lights come on over the door contact.
• The safe securing system is deactivated.
• The windows open provided the key is held* in the unlock position. On vehicles
fitted with anti-theft alarm system the window operation is only possible 45 seconds
after deactivation of the warning system.
• The indicator light in the driver's door stops flashing if the vehicle is not fitted with
an anti-theft alarm system* ⇒ page 46.
Note
If the vehicle is equipped with an anti-theft alarm system*, you must unlock the vehicle
by inserting the key into the driver door you then have to insert the key into the ignition
lock and switch the ignition on within 15 seconds after opening the door. The alarm
will be triggered if you do not switch on the ignition within 15 seconds.
Locking the vehicle with the key
– Turn the key in the locking cylinder of the driver's door in the opposite direction of
travel (lock position) ⇒ fig. 33.
• The doors, the boot lid and the fuel filler flap* are locked.
• The switched on interior lights will switch off over the door contact.
• The windows and the electric sliding/tilting roof* close provided the key is held in
the lock position.
• The safe securing system is activated immediately.
• The indicator light in the driver door begins flashing.
Note
The opened driver door cannot be locked. It must be locked separately after closing
it.
Fig. 33 Turning the key for unlocking and
locking the vehicle
A
A
A
B
sgg.6.book Page 42 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 43
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Button for the central locking system
If the vehicle was not locked from outside, you can also unlock and lock it with the
rocker switch on the centre console without the ignition switched on.
Locking all doors and the boot lid
– Press button ⇒ page 43, fig. 34. The symbol in the button comes on.
Unlocking all doors and the boot lid
– Press button ⇒ page 43, fig. 34. The symbol goes out in the button.
The following applies if you have locked your vehicle using the button :
• It is not possible to open the doors or the boot lid from the outside (safety feature,
e.g. when stopping at traffic lights etc.).
• You can unlock the doors individually from the inside and open them by pulling the
door opening lever.
• As long as one door is opene d
7)
, the doors cannot be locked in order to avoid inad-
vertently locking the key in the vehicle.
• In the event of an accident in which the airbags are deployed, the locked doors are
automatically unlocked from the inside in order to enable rescuers to gain access to
the vehicle.
By pressing and holding the button or , you can conveniently close or open the
windows ⇒ page 49.
WARNING
The central locking system also operates if the ignition is switched off. All the
doors and the boot lid are locked. Children should never be left unattended in
the vehicle since it is difficult to provide assistance from the outside when the
doors are locked. Locked doors make it difficult for rescuers to get into the
vehicle in an emergency - hazard!
Note
The door opening lever and the buttons for the central locking system do not operate
if the safe securing system is activated.
Emergency locking of the doors
All the other doors without locking cylinder have an emergency locking which is only
visible once the door is opened. The emergency locking must be used in particular if
the vehicle battery fails.
Locking
– Remove the panel ⇒ fig. 35.
– Insert the key into the slot and turn it into the horizontal position in the direc-
tion of the arrow (mirror-inverted on the right doors).
– Re-insert the panel.
7)
Is not valid for the boot lid.
Fig. 34 Centre console: Buttons for
central locking
A
1
A
2
A1A1A
2
Fig. 35 Rear door: Emergency locking of
the door
A
A
A
B
sgg.6.book Page 43 Thursday, September 24, 2009 2:32 PM
Unlocking and locking44
After closing the door, you can no longer open it from outside. If the child safety lock
is not switched on, it is possible to open the door from the inside by pulling once on
the door handle. If the child safety lock is activated (only on the rear doors), first of all
it is necessary to pull once on the inner door handle and then open the door from the
outside.
Boot lid
Open the boot lid by pressing the hand grip above t he licence plate after unlocking the
vehicle using the key or the radio remote control.
Opening the boot lid
–Press on the handle ⇒ fig. 36 and at the same time raise the boot lid.
Closing the boot lid
– Pull the boot lid down and close it with a slight swing ⇒ .
A handle which makes the closing easier is located on the inner paneling of the boot
lid.
WARNING
• Ensure that the lock is properly engaged after closing the boot lid. Other-
wise, the boot lid might open suddenly when driving even if the boot lid lock is
closed - risk of accident!
• Never drive with the boot lid fully opened or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!
• Do not press on the rear window when closing the boot lid, it could crack -
risk of injury!
Note
• After closing the boot lid, it is automatically locked within 2 seconds and the
anti-theft alarm system* is activated. This applies only if the vehicle was locked
before closing the boot lid.
• The function of the hand grip above the licence plate is deactivated when starting
off or as of a speed of more than 5 km/hour for vehicles with central locking. The function of the hand grip is activated again when the vehicle has stopped and a door is
opened.
Emergency unlocking of the boot lid
If there is a fault in the central locking, you can open the boot lid as follows:
– Fold one of the outer rear seats forwards.
– Move the operating lever with the aid of a narrow object, e.g. a screwdriver, up to
the stop in the direction of arrow and then unlock the boot lid in the direction
of arrow .
– Open the boot lid/luggage compartment door from outside.
Fig. 36 Handle of b oot lid
WARNIN G (continued )
Fig. 37 Emergency unlocking of the boot
lid
A
1
A
2
sgg.6.book Page 44 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 45
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Remote control*
Description
You can use the remote control:
• to unlock and lock the car,
• unlocking boot lid,
• electrically open and close the windows.
The transmitter with the battery is incorporated in the handle of the remote control
key. The receiver is located in the interior of the car. The operating range of the remote
control is approx. 10 m. But this range of the remote control can be reduced if the
batteries are weak.
The remote control key has a fold-open key bit which can be used for unlocking and
locking the car manually and also for starting the engine.
If a lost key is replaced or if the receiver unit has been repaired or a new unit installed,
it is then necessary for a specialist garage to adapt the system. Only after this is it
possible to again use the remote control.
Note
• The remote control is automatically deactivated when the ignition is switched on.
• The operation of the remote control may temporarily be affected by interference
from transmitters close to the car and which operate in the same frequency range (e.g.
mobile phone, TV transmitter).
• The battery must be replaced, ideally by a specialist garage, if the central locking or
anti-theft alarm system does react to the remote control at less than 3 metres away.
• If the driver door is opened, the vehicle cannot be locked using the remote
control.
Unlocking and locking car
Unlocking the vehicle
– Press the button ⇒ fig. 38 for about 1 second.
Locking the vehicle
– Press button for about 1 second.
Deactivating safe securing system
– Press button twice in 2seconds. Further information ⇒ page 41.
Boot lid remote release
– Press button for about 2 second. Further information ⇒ page 44.
Folding out of the key
– Press button .
Folding up of the key
– Press button and collapse the key bit in the housing.
The turn signal lights flash twice as confirmation that the vehicle has been unlocked.
The vehicle will lock again automatically if you unlock the vehicle using button but
do not open a door or the boot lid within the next 30 seconds. This function is intended
to prevent the car being unlocked unintentionally.
Fig. 38 Remote control key
A
1
A
3
A
3
A
2
A4A4A
1
sgg.6.book Page 45 Thursday, September 24, 2009 2:32 PM
Unlocking and locking46
In addition, when the car is unlocked, the electrically adjustable seats and exterior
mirrors* move into the position assigned to this key. The stored setting of driver seat
and exterior mirrors is retrieved.
Display of the locking
The turn signal lights flash once to confirm that the vehicle has been correctly locked.
If the vehicle is locked by pressing the button and some doors or the boot lid are
not closed, the turn signal lights flash only after closing.
WARNING
If the vehicle is locked from the outside and the safe securing system is activated, there must not be any person in the vehicle as it is then not possible to
open either a door or a window from the inside. The locked doors make it more
difficult for rescuers to get into the vehicle in an emergency - hazard!
Note
• Operate the radio remote control only when the doors and boot lid are closed and
you have visual contact with the vehicle.
• Once in the car, you must not press the lock button of the radio remote control
before inserting the key into the ignition lock in order to avoid the car being inadvertently locked and the alarm system* being switched on. Should this happen, press the
unlock button of the radio remote control.
Synchonisation of the remote control
If the vehicle cannot be unlocked by actuating the remote control system then it is
possible that the code in the key and the control unit in the vehicle are no longer
synchronised. This can occur when the buttons on the radio-operated key are actuated
a number of times outside of the operative range of the equipment or the battery on
the remote control was replaced.
This means it is necessary to synchronise the code as follows:
• Press any button on the remote control.
• pressing of the button means that the door will unlock with the key within 1
minute.
Anti-theft alarm system*
Description
The anti-theft alarm system increases the level of protection against people seeking to
break into the vehicle. The system triggers audible and visual warning signals if an
attempt is made to break into the vehicle.
How is the alarm system activated?
The anti-theft alarm system is activated automatically when the vehicle is locked with
the key on the closed driver's door or by using the radio remote control. It is activated
30 seconds after locking the door.
How is the alarm system deactivated?
The anti-theft alarm system is deactivated if the vehicle is unlocked by only using the
radio remote control. The vehicle is automatically locked again if the vehicle is not
opened within 30 seconds after reactivating the anti-theft alarm system.
Once you unlock the vehicle by inserting the key into the driver door you then have to
insert the key into the ignition lock and switch the ignition on within 15 seconds after
opening the door in order to deactivate the anti-theft alarm system. The alarm will be
triggered if you do not switch on the ignition within 15 seconds.
When is the alarm triggered?
The following security areas of the locked vehicle are monitored:
• Bonnet,
• Boot lid,
• Doors,
• Ignition lock,
• Angle of the vehicle* ⇒ page 47,
• Vehicle interior* ⇒ page 47,
• A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either of the two battery terminals is disconnected
while the anti-theft alarm system is activated.
A
3
sgg.6.book Page 46 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 47
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
How is the alarm switched off?
You switch the alarm off if you unlock the vehicle with the radio remote control or if you
switch the ignition on.
Note
• The working life of the alarm siren is 6 years. More detailed information is available
by a specialist garage.
• Before leaving the car, check that all the doors, windows and the electric
sliding/tilting roof* are properly closed in order to ensure that the anti-theft alarm
system is fully operational.
• Coding of the radio remote control and the receiver unit precludes the use of the
radio remote control from other vehicles.
Interior monitor* and Towing protection monitoring*
Switch off the interior monitor and towing protection monitoring
– Switch off the ignition.
– Open the driver door.
– Press the button at the centre column on the driver side ⇒ fig. 39, the symbol
which lights up in the button changes from red to orange.
– Lock the vehicle within 30 seconds.
The interior monitor and the towing protection monitoring are switched on again
automatically the next time the car is locked.
Note
• You can switch the interior monitor and the towing protection monitoring off if
there is a possibility that movements from (e.g. children or animals) inside the vehicle
interior or if the vehicle must be transported (e.g. by train or ship) or towed, might
trigger the alarm.
• The opened storage compartment for spectacles reduces the effectiveness of the
interior monitor. In order to ensure the function of the interior monitor to be fully
operational, always close the storage compartment for spectacles before locking the
vehicle.
Power windows*
Buttons on the driver's door
The power windows operate only when ignition is switched on.
Opening a window
– A window is opened by pressing lightly on the respective button in the door. The
process stops when one releases the button.
– Additionally you can open the window automatically (fully opened) by pressing the
button up to the stop. Renewed pressing of the button causes the window to stop
immediately.
Fig. 39 Button for interior monitor and
towing protection monitoring
Fig. 40 Buttons on the driver's door
sgg.6.book Page 47 Thursday, September 24, 2009 2:32 PM
Unlocking and locking48
Closing a window
– A window is closed through pulling lightly on the respective button in the door. The
closing process stops when one releases the button.
– Additionally you can close the window automatically (fully closed) by pulling the
button up to the stop. Renewed pulling of the button causes the window to stop
immediately.
The buttons for the individual windows are located in the armrest of the driver's door
⇒ page 47, fig. 40, front passenger door and in the rear doors* ⇒ page 48.
Buttons for the power windows in the armrest for the driver
Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window in the rear door on the right*
Button for the power window in the rear door on the left*
Safety pushbutton*
Safety pushbutton*
You can deactivate the buttons for power windows at rear doors by pressing the safety
pushbutton ⇒ page 47, fig. 40. The buttons for power windows at rear doors are
activated again by pressing the safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light in the safety
switch lights up.
WARNING
• If you lock the vehicle from the outside, do not leave any person in the
vehicle since it is no longer possible to open the windows from the inside in an
emergency.
• The system is fitted with a force limiter ⇒ page 49. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a result of getting an arm, for example,
jammed in the window!
• It is recommended to deactivate the electrically operated power windows in
the rear doors (safety pushbutton) ⇒ page 47, fig. 40 when children are
being transported on the rear seats.
Note
• After switching the ignition off, it is still possible to open or close the windows for a
further 10 minutes. The automatic closing and opening functions will not operate
during this time. The power windows are switched off completely once you open the
driver or front passenger door.
• When driving always use the existing heating, air conditioning and ventilation
system for ventilating the interior of the vehicle. If the windows are opened, dust as
well as other dirt can get into the vehicle and in addition the wind noise is more at
certain speeds.
Button in front passenger door and in rear doors
A button for the relevant window is provided in these doors.
Opening a window
– Lightly press the appropriate button down and hold it until the window has moved
into the desired position.
A
A
ABACADASA
S
ASA
S
WARNIN G (continued )
A
S
Fig. 41 Position of button in front
passenger door
sgg.6.book Page 48 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 49
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– Additionally you can open the window automatically (fully opened) by pressing the
button down up to the stop. Renewed pressing of the button causes the window
to stop immediately.
Closing a window
– Lightly press the appropriate button up and hold it until the window has moved
into the desired position.
– Additionally you can close the window automatically (fully closed) by pressing the
button up up to the stop. Renewed pressing of the button causes the window to
stop immediately.
WARNING
The system is fitted with a force limiter ⇒ page 49. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a result of getting an arm, for example,
jammed in the window!
Note
• After switching the ignition off, it is still possible to open or close the windows for a
further 10 minutes. The automatic closing and opening functions will not operate
during this time. The power windows are switched off completely once you open the
driver or front passenger door.
Force limiter of the power windows
The electrically operated power windows are fitted with a force limiter. It reduces the
risk of bruises or injuries when closing the windows.
If there is an obstacle, the closing process is stopped and the window goes down by
several centimeters.
If the obstacle prevents the window from being closed during the next 10 seconds, the
closing process is interrupted once again and the window goes down by several
centimeters.
You must try to close the window once again within 10 seconds after the window has
gone down twice, even if the obstacle was not yet removed, the closing process is
stopped. During this time it is not possible to automatically close the window. The
force limiter is still switched on.
The force limiter is only switched off, if you attempt to close the window within the next
10 seconds - the window closes now with full strength!
If you wait longer than 10 seconds, the force limiter is switched on again.
WARNING
You should take particular care when closing the windows! You may otherwise
suffer severe injuries as a result of getting an arm, for example, jammed in the
window!
Window convenience operation
You can open and close the electrically powered windows as follows when unlocking
and locking the vehicle (only close the sliding/tilting roof).
Opening a window
– Hold the key in the locking cylinder of the driver's door in the unlock position or
press the unlock button of the radio remote control until all the windows are
opened.
Closing a window
– Hold the key in the locking cylinder of the dr iver's door in the lock position or press
the lock button of the radio remote control until all the windows are closed.
You can interrupt the opening or closing operation of the windows immediately by
releasing the key or the lock button.
WARNING
The system is fitted with a force limiter ⇒ page 49. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
sgg.6.book Page 49 Thursday, September 24, 2009 2:32 PM
Unlocking and locking50
otherwise suffer severe injuries as a result of getting an arm, for example,
jammed in the window!
Note
• On vehicles fitted with anti-theft alarm system the convenience window opening
is possible by means of the key in the locking cylinder only 45 seconds after deactivating the warning system or after activating the anti-theft alarm system.
Operational faults
Electrically operated power windows do not operate
If the battery of the car has been disconnected and then reconnected, the electrically
operated power windows do not operate. The system must be activated. Proceed as
follows in order to re-establish the function:
• Switch on the ignition.
• Press the relevant switch top and hold it pressed as long as necessary until the
window is closed.
• Release the switch.
• Press once again the relevant switch top and hold it pressed for approx. 3 seconds.
Operation in winter
Ice accumulating on the surface of the windows during the winter may result in a
greater resistance when closing the windows and the window may stop and go down
several centimetres.
It is necessary to put the force limiter out of operation in order to close the window
⇒ page 49, “Force limiter of the power windows”.
WARNING
The system is fitted with a force limiter ⇒ page 49. If there is an obstacle, the
closing process is stopped and the window goes down by several centimeters.
You should then take particular care when closing the windows! You may
otherwise suffer severe injuries as a result of getting an arm, for example,
jammed in the window!
Electric sliding/tilting roof with electric sun screen*
Description
Fig. 42 Control dial for the power sliding/tilting roof / button for the electric sun screen
The sliding/tilting roof with electric sun screen can only be operated with the control
dial when the ignition is switched on ⇒ fig. 42. The control dial has a number of positions.
You can open or close the electric sun screen separately with the aid of the button
⇒ fig. 42 on the right.
After switching the ignition off, it is still possible to open, close and tilt the sliding/tilting
roof or the electric sun screen for approx. 10 minutes. It is no longer possible to operate
the sliding/tilting roof and the electric sun screen after opening one of the front doors,
however.
Note
The sliding/tilting roof must be initialised after disconnecting and reconnecting the
vehicle battery. The initialisation is performed by holding the switch for approx. 10
seconds in the position in order to close the sliding/tilting roof.
WARNIN G (continued ) WARNIN G (continued )
A
A
sgg.6.book Page 50 Thursday, September 24, 2009 2:32 PM
Unlocking and locking 51
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Opening and tilting
Comfort position
– Turn the switch to position ⇒ fig. 42.
Opening fully
– Turn the switch to position and hold it in this position (spring-tensioned posi-
tion).
Tilting and closing
– Pull up the rear switch ⇒ page 50, fig. 42.
– Press down the switch on the recess and then push it forward in order to close the
sliding/tilting roof.
The wind noise in the comfort position is less than when the roof is fully opened.
Caution
It may be necessary during winter to remove any ice and snow in the area of the
sliding/tilting roof before opening it in order to prevent damaging the opening
mechanism.
Closing
Sliding closed/closing the sliding/tilting roof
– Turn the switch to position ⇒ page 50, fig. 42.
Safety closing
The sliding/tilting roof is fitted with a force limiter. The sliding/tilting roof stops and
moves back several centimetres when it cannot be closed because there is something
in the way (e.g. ice). You can close the sliding/tilting roof completely without force
limiter by pressing the switch to the position ⇒ page 50, fig. 42 at the front for as
long as it takes for the sliding/tilting roof to close completely ⇒ .
WARNING
Close the sliding/tilting roof carefully - risk of injury!
Convenience operation
You can also close an open sliding/tilting roof from the outside.
– Hold the key in the locking cylinder of the dr iver's door in the lock position or press
the lock button of the remote control until the sliding/tilting roof is closed.
The closing operation stops when one releases the key or the lock button.
Note
The force limiter also operates for convenience closing.
Emergency operation
Fig. 43 Detail of the headliner: Points for positioning screwdriver / opening for positioning
the key
You can close and/or open the sliding/tilting roof by hand if the system is defect.
– Position the flat blade of a screwdriver carefully against the rear edge of the cover
of the electrical drive at the points of the arrows ⇒ fig. 43.
–Pull the cover down.
A
C
ABA
A
A
A
A
1
sgg.6.book Page 51 Thursday, September 24, 2009 2:32 PM
Unlocking and locking52
– Insert an Allen key, Group 4, up to the stop into the opening at the point of the
arrow and close and/or open the sliding/tilting roof ⇒ fig. 43.
– Press on the cover again by first of all inserting the plastic lugs and then pushing the
cover up.
– Have the fault rectified by a specialist workshop.
Note
It is necessary after each emergency operation to initialise the sliding/tilting roof. The
initialisation is performed by holding the switch for approx. 10 seconds in the position
⇒ page 50, fig. 42 in order to close the sliding/tilting roof.
A2A
A
sgg.6.book Page 52 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 53
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Lights and Visibility
Lights
Switching lights on and off
Switching on side lights
– Turn the light switch into position .
Switching on the low beam and main beam
– Turn the light switch into position .
– Press the main beam lever forward in order to switch on the main beam
⇒ page 59, fig. 50.
Switching off lights (except daylight driving lights)
– Turn the light switch into position°0.
Low beam comes on only if the ignition is switched on. After switching off the ignition,
the low beam is switched off automatically and only the side lights come on. For vehicles which are equipped with the function Coming/Leaving-Home* ⇒ page 55, the
side lights also go out.
On models fitted with right-hand steering the position of certain switches differs
from that shown in ⇒ fig. 44. The symbols which mark the switch positions are identical, however.
WARNING
Never drive with side lights on - risk of accident! The side lights are not bright
enough to light up the road sufficiently in front of you or to be seen by other
oncoming traffic. In this case, always switch on the low beam when it is dark or
if visibility is poor.
Note
• An audible warning will sound if you withdraw the ignition key and open the
driver's door when the vehicle lights are still on.
• The acoustic warning signal is switched off over the door contact when the driver's
door is closed (ignition off). The vehicle can be parked with the side lights on.
• If the car is parked for a lengthy period, we recommend switching off all lights, or
leaving only the parking lights switched on.
• The switching on of the described lights should only be undertaken in accordance
with the legal requirements.
• If a fault occurs in the light switch, the low beam comes on automatically.
• In the event of cool or humid weather conditions, the headlights can be misted up
from inside.
− The temperature difference between interior and external area of the headlight
lenses is decisive.
− When the driving lights are switched on, the light outlet surfaces are free from
mist after a short period. The headlight lenses can possibly mist up at the border
areas.
− It also concerns reverse light and turn signal lights.
− This mist has no influence on the life of the lighting system.
Daylight driving lights
In some countries, the national legal provisions require that the vehicles are equipped
with the function daylight driving lights.
Fig. 44 Dash panel: Light switch
sgg.6.book Page 53 Thursday, September 24, 2009 2:32 PM
Lights and Visibility54
Switching on daylight driving lights
– Switch on the ignition without turning the light switch out of the position 0.
Deactivating the function daylight driving lights
– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the bottom and hold it in
this position for at least 3 seconds.
Activating the function daylight driving lights
– Pull the turn signal light lever towards the steering wheel up to 3 seconds after
switching on the ignition and at the same time, slide it to the top and hold it in this
position for at least 3 seconds.
When the daylight driving lights are switched on, the side lights and the low beam
come on together.
In some countries, the national legal provisions require that the parking lights com e on
together with the bulbs for daylight d riving lights when activa ting the function daylight
driving lights.
On vehicles which are fitted with bulbs for daylight driving lights in the fog lights, the
parking lights do not come on when activating the function daylight driving lights.
When the daylight driving lights are switched on, the illumination of the instrument
cluster is switched off, however, it is switched on in the position when it is dark
and the low beam shines with full brightness (100% of the performance).
On vehicles fitted with an information display*, you can also activate or deactivate in
the menu the function daylight driving lights:
Setup
Lights & Vision (Lights & Vision)
Automatic driving lamp control*
Switching on automatic driving lamp control*
– Turn the light switch ⇒ fig. 45 into position .
Switching off automatic driving lamp control*
– Turn the light switch to the position 0, or .
If the light switch is in the position , the symbol illuminates when the ignition is
switched on next to the light switch. If the low beam is activated with the light
sensor, the symbol illuminates additionally next to the light switch.
If the light comes on automatically, the side lights and low beam as well as licence plate
light light up at the same time.
If the automatic light control is switched on, the light is regulated with the light sensor
in the rear mirror holder. If the light intensity drops below the set value, e.g when
driving during the day into a tunnel, the low beam and the side lights as well as the
licence plate light come on automatically. If the light intensity increases again, the
lights switch off automatically.
Motorway lights
If the automatic light control has been switched on and the vehicle speed is over 140
km/h for at least 10 seconds, the side lights and low beam are switched on automatically.
If the vehicle speed is below 65 km/h for at least 2 minutes, the lights are switched off.
Fig. 45 Dash panel: Light switch
sgg.6.book Page 54 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 55
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Rain lights
If you switch on the windscreen wipe in the operation rain sensor* for longer than 10
seconds or in the operation permanent wipe (position 2 or 3) ⇒ page 63 switching on
for longer than 15 seconds, the side lights and low beam are switched on automatically. The light switches off if the windscreen wipe is in operation rain sensor* for more
than 4 minutes or is not switched on in the operation permanent wipe.
WARNING
The automatic light control only operates as a support. The driver is not
released from his responsibility to inspect the light and if necessary to switch on
the light depending on the light conditions. The light sensor cannot detect for
example rain or snow. For these conditions we recommend to switch on the low
beam !
Note
• Do not affix any stickers in front of the light sensor, so that you do not impair its
function or put it out of operation.
• The same principles as for using the automatic light control also apply to the light
which is switched on manually ⇒ page 53.
Cornering lights*
The cornering lights are used to illuminate the curves by means of the cone of light
swiveling together with the front headlight with Xenon lights*. This function is active
when the speed of the car increases to more than 10km/h.
The swiveling function of the headlights can be switched off / on via the menu point
Assistant in the main menu of the Information display* ⇒ page 24.
WARNING
If the cornering lights are defective, the headlights are automatically lowered to
the emergency position, which prevents a possible dazzling of oncoming traffic.
Thus the illuminated length of the road is shortened. Drive carefully and have
the car inspected immediately by a specialist garage.
Coming Home Function
The function makes it possible to switch on the lights in the darkness for a short time
after leaving the vehicle.
Switching on Coming Home Function
– The light switch is in the position automatic driving lamp control and the low
beam illuminates.
– Switch off the ignition.
– After opening the driver's door, the function Coming Home is switched on.
– Close all the doors and the boot lid and lock the vehicle. After a short time, switch
all lights off.
Depending on equipment fitted the function Coming Home switches on the following
lights:
• Parking lights,
• Low beam,
• Entry lighting in the exterior mirrors,
• Licence plate light.
Coming Home Function
The lights go out 10 seconds after closing all the doors and the boot lid.
If a door or the boot lid remains open, the lights go out 60 seconds after switching off
the ignition.
The function Coming Home is controlled with the light sensor in the mount of the interior rear mirror. If the light intensity is higher than the set value of the light sensor, the
Coming Home Function is not switched on after switching off the ignition.
Note
• If the Coming Home Function is switched on constantly, the battery will be heavily
discharged particularly in short-haul traffic.
• The switching on of the described lights should only be undertaken in accordance
with the legal requirements.
sgg.6.book Page 55 Thursday, September 24, 2009 2:32 PM
Lights and Visibility56
• You can change the illumination period for the Coming Home Function by means
of the information display*.
Leaving Home Function
This function makes it possible to switch on the lights when approaching the vehicle.
Switching on Leaving Home Function
– Unlock the vehicle with the radio remote control - the lights come on.
Depending on equipment fitted the function Leaving Home switches on the following
lights:
• Parking lights,
• Low beam,
• Entry lighting in the exterior mirrors,
• Licence plate light.
Leaving Home Function
The function Leaving Home is controlled with the light sensor in the mount of the interior rear mirror. If the light intensity is higher than the set value of the light sensor, the
Leaving Home Function is not switched on after unlocking the vehicle with the radio
remote control.
After unlocking the vehicle with the radio remote control, the lights come on for 10
seconds. The Leaving Home Function is also switched off after the ignition is switched
on and after locking the vehicle.
If no door is opened within 30 seconds, the lights go out and the vehicle is locked automatically.
Note
• If the Leaving Home Function is switched on constantly, the battery will be heavily
discharged particularly in short-haul traffic.
• The switching on of the described lights should only be undertaken in accordance
with the legal requirements.
• You can change the illumination period for the Leaving Home Function by means
of the information display*.
Tourist light*
Xenon headlight
This mode makes it possible to drive in countries with opposing traffic system, driving
on the left/right, without dazzling the oncoming vehicles. When the mode “tourist
light” is active, the side to side swivel of the headlights is deactivated.
The mode “tourist light” is activated / deactivated via the information display* in the
menu:
SETUP (Settings)
Tr ave l mod e
Off
On
Halogen headlight
When using Halogen headlights, it is necessary to stick a sticker over a certain part of
the headlights in order to prevent the dazzling of oncoming traffic.
You can purchase headlight stickers from the range of the Škoda original accessories.
Fog lights*
Fig. 46 Dash panel: Light switch
sgg.6.book Page 56 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 57
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Switching on the fog lights
– First of all turn the light switch into position or ⇒ page 56, fig. 46.
– Pull the light switch into position .
The rear fog light warning light ⇒ page 29 lights up in the instrument cluster when
the fog light is switched off.
Fog lights with the function “Corner”*
The fog lights with the function “Corner” improve the illumination of
areas close to the vehicle when turning, parking etc.
The fog lights with the function “Corner” are regulated according to the steering angle
or after switching on the turn signal light8) in the following circumstances:
• the vehicle is stationary and the engine is running or it moves with a speed of
maximum 40 km/h;
• the daylight driving lights are not switched on;
• the low beam is switched on or the light switch is in the position and the
intensity of the ambient light causes the low beam to be switched on;
• the fog lights are not switched on;
• no reverse gear is engaged.
Note
If you engage the reverse gear during the active function “Corner”, both fog lights
illuminate.
Rear fog light
Switching on the rear fog light
– First of all turn the light switch into position or ⇒ page 56, fig. 46.
– Pull the switch into position .
The rear fog light warning light ⇒ page 29 lights up in the instrument cluster when
the fog light is switched off.
Only the rear fog light of the trailer lights up automatically when you are towing a trailer
using a factory-fitted towing device which is fitted with the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on if visibility is particularly poor (conform
with any varying legal provisions) to avoid dazzling vehicles behind your vehicle.
Instrument lighting*
You can adjust the brightness of the instrument lighting.
Instrument lighting
– Switch on the light.
– Turn the control dial ⇒ fig. 47 to the desired intensity of the instrument lighting.
For the information display* ⇒ page 24 the intensity of the lighting is automatically
set. It is only possible to adjust the instrument lighting with the control dial if the light
intensity drops below the set value of the light sensor.
8)
If both switch on versions are conflicting, for example if the steering wheel is turned to the left
and the right turn signal light is switched on, the turn signal light has the higher priority.
A
1
A
2
Fig. 47 Dash panel: Instrument lighting
sgg.6.book Page 57 Thursday, September 24, 2009 2:32 PM
Lights and Visibility58
Headlamp range adjustment
Once the low beam is switched on you can then adapt the range of the
headlights to the load of the vehicle.
– Turn the control dial ⇒ fig. 48 until you have adjusted the low beam so that
oncoming traffic is not dazzled.
Settings
The positions correspond approximately to the following vehicle loads:
Front seats occupied, luggage compartment empty.
All seats occupied, luggage compartment empty.
All seats occupied, luggage compartment laden.
Driver seat occupied, luggage compartment laden.
Caution
Set the headlight beam adjustment in such a way as to avoid dazzling oncoming traffic.
Note
Headlights fitted with Xenon bulbs* adapt automatically to the load and driving state
of the vehicle (e.g. accelerating, braking) when the ignition is switched on and when
driving. Vehicles which are equipped with Xenon bulbs* do not have a manual headlight range adjustment control.
Switch for hazard warning lights
– Press switch ⇒ fig. 49 to switch the hazard warning light system on or off.
All the turn signal lights on the vehicle flash at the same time when the hazard warning
light system is switched on. The indicator light for the turn signals and the indicator
light in the switch also flash at the same time. You can also switch on the hazard
warning light system if the ignition is switched off.
The hazard warning light system is switched on automatically if an airbag is deployed
in the event of an accident.
Please comply with any legal requirements when using the hazard warning light
system.
Note
Switch on the hazard warning light system if, for example:
• you encounter traffic congestion,
• your vehicle breaks down or an emergency situation occurs.
Fig. 48 Dash panel: Lights and Visibility
A-A
1
A
2
A
3
Fig. 49 Dash panel: Switch for hazard
warning lights
sgg.6.book Page 58 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 59
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The turn signal and main beam lever
The parking lights and headlight flasher are also switched on and off
using the turn signal and main beam lever.
The turn signal and main beam lever perform the following functions:
Right and left turn signal light
– Push the lever upwards or downwards ⇒ fig. 50.
– If you only wish to flash three times* (the so-called convenience turn signal), push
the lever briefly up to the upper or lower pressure point and release it. This function
can be activated/deactivated in the information display* ⇒ page 24.
– Turn signal for changing lanes - in order to only flash briefly, move the lever up or
down to the pressure point and hold it in this position.
Main beam
– Switch on the low beam.
– Push the lever forwards.
– Pull the lever back into the initial position in order to switch the main beam off
again.
Headlight flasher
– Pull on the lever of the steering wheel (sprung position) - the main beam and
warning light in the instrument cluster come on.
Parking light
– Switch off the ignition.
– Push the lever up or down - the right-hand or left-hand parking light is switched
on.
Information concerning the function of the lights
• The turn signal system only operates when the ignition is switched on. The corre-
sponding indicator light or in the instrument cluster also flashes.
• The turn signal is automatically cancelled after negotiating a curve.
• The indicator light flashes at twice its normal rate if a bulb of the turn signal light
fails.
• The side light and rear light on the appropriate side of the vehicle are switched on
when the parking light is selected. The parking light only operates if the ignition is
switched off.
Caution
Use main beam or the headlight flasher only if this does not risk dazzling other road
users.
Note
• If you have switched on the right or left turn signal light and you switch off the igni-
tion, the parking light is not automatically switched on.
• Use only in accordance with the legal requirements the described lighting and
signal systems.
Fig. 50 Turn signal and main beam lever
sgg.6.book Page 59 Thursday, September 24, 2009 2:32 PM
Lights and Visibility60
Interior lighting
Vehicle interior lighting in the front and lighting of storage
compartment on front passenger side
Fig. 51 Front vehicle interior lighting
Switching the interior light on
– Press the switch at the point of the symbol ⇒ fig. 51.
Switching the interior light off
– Press the switch at the point of the symbol O.
Door contact setting
– Position the switch into middle position. On vehicles without interior monitor*, the
middle position is marked with a symbol ⇒ fig. 51 on the left.
Lighting of storage compartment on the front passenger side
– When opening the flap of the storage compartment on the front passenger side the
lighting in the storage compartment comes on.
– The light switches on automatically when the parking light is switched on and goes
out when the flap is closed.
The interior light comes on as soon as you unlock the car or open a door or when the
ignition key has been removed. The light goes out again about 30 seconds after all the
doors have been closed. The interior lighting is switched off when you lock the car or
switch the ignition on. This only applies when the switch for the corresponding interior
lights is standing n the door contact setting.
The interior lighting goes off after about 10 minutes when a door has been left open in
order to avoid discharging the battery of the vehicle.
If the switch is in the position (permanent lights), the interior lighting goes off at the
latest after 10 minutes in order to avoid discharging the battery of the vehicle.
Two diffuse lights* are integrated in the interior lighting, which illuminates the shift
lever and the middle of the dash panel. They are switched on automatically when
switching on the parking light.
On vehicles with interior monitor, the illumination unit does not have any diffuse
lights*.
Note
We recommend having these bulbs replaced by a specialist garage.
Front reading lights
Fig. 52 Front reading lights
Front reading lights
– You switch on or off the reading light on the right or left by pressing the switch
⇒ fig. 52.
sgg.6.book Page 60 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 61
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Rear reading lights
Switching the interior light on
– Press the cover glass in the area of the symbol ⇒ fig. 53.
Switching the interior light off
– Press the cover glass in the area of the symbol O ⇒ fig. 53.
Door contact setting
– Position the cover glass into middle position .
Front door warning light*
The warning light is located in the door trim panel below ⇒ fig. 54.
The warning light goes on every time the door is opened. The light goes out about 10
minutes after opening the door in order to avoid discharging the battery of the vehicle.
There is a reflector installed on some vehicles instead of the warning light.
Luggage compartment light
The lighting comes on automatically when the boot lid is opened. The luggage
compartment lighting will switch off again automatically if the boot lid remains open
for more than about 30 minutes.
Entry lighting*
The lighting is positioned on the bottom edge of the exterior mirror.
The light beam is directed towards the entry area of the front door.
The light comes on after the doors have been locked or on opening the boot lid. The
light goes out after switching on the ignition or up to 30 seconds after closing all the
doors, the bonnet and the boot lid.
If a door, the bonnet or the boot lid remains open, the light goes out within 2 minutes
if the ignition is switched off.
WARNING
If the entry light comes on, do not touch its cover - risk of burns!
Fig. 53 Detail of the headliner: Rear
reading lights
Fig. 54 Front door: Warning light
sgg.6.book Page 61 Thursday, September 24, 2009 2:32 PM
Lights and Visibility62
Visibility
Rear window heater
– You can switch the rear window heater on or off by pressing the switch
⇒ fig. 55 - the indicator light in the switch comes on or goes out.
The rear window heater only operates when the engine is running.
The rear window heater switches off automatically after 10 minutes.
For the sake of the environment
As soon as the window is de-iced or free from mist, the heating should be switched off.
The reduced current consumption will have a favourable effect on fuel economy
⇒ page 177, “Saving electricity”.
Note
• The position and the shape of the switch can differ depending on equipment
installed in the vehicle.
• If the on-board voltage drops, the rear window heater is switched off automatically,
in order to provide sufficient electrical energy for the engine control.
Sun visors
Fig. 56 Sun visor: Swivelling out / double sun visor: Folding out
You can pull the sun visor for the driver or front passenger out of the fixture and swivel
it toward the door in the direction of the arrow ⇒ fig. 56.
The vanity mirrors* in the sun visors are provided with covers. Push the cover in direction of arrow .
On vehicles which are equipped with double sun visor*, you can also unfold the auxiliary visor in direction of arrow after swivelling the sun visor ⇒ fig. 56.
WARNING
The sun visors must not be swivelled to the side windows into the deployment
area of the head airbags if any objects, such as ball-point pens etc. are attached
to them. This might result in injuries to the occupants if the head airbag is
deployed.
Fig. 55 Switch for rear window heater
A
1
A
2
A
3
sgg.6.book Page 62 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 63
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Windshield wiper and wash system
Windshield wiper
You can operate the windscreen wipers and automatic wipe/wash
using the windscreen wiper lever.
The windscreen wiper lever ⇒ fig. 57 has the following positions:
Finger-operated wiping
– If you wish to wipe the windscreen only briefly, push the lever into the sprung
position . If you hold the lever in the lower position for more than 1 second, the
wiper wipes faster.
Intermittent wiping
– Position the lever up into position .
– Set with the switch the desired break between the individual wiper strokes.
Slow wipe
– Position the lever up into position .
Fast wipe
– Position the lever up into position .
Automatic wipe/wash for windscreen
– Pull the lever towards the steering wheel into sprung position , the wash system
sprays immediately, the windscreen wiper starts wiping a little later. The wash
system and the windscreen wiper operate simultaneously at a speed of more than
120 km/h.
– Release the lever. The windscreen wash system stops and the wiper continues for
another 3 - 4 wiper strokes (depending on the period of spraying of the windscreen). At a speed of more than 2 km/h, the wiper wipes once again* 5 seconds
after the last wiper stroke in order to wipe the last drops from the windscreen. This
function can be activated/deactivated by a specialist garage.
Rain sensor*
– Move the lever into position .
– You can set the sensitivity of the sensor individually with switch .
Wiping the rear window pane
– Push the lever away from the steering wheel into position - the widescreen
wiper will operate every 6 seconds.
Automatic wipe/wash for the rear window pane*
– Press the lever from the steering wheel forward into the sprung position , the
wash system sprays immediately, the windscreen wiper starts wiping a little later.
As lon g as you hol d t he l eve r in thi s po sit ion , th e w ipe r op erat es a s w ell as t he w ash
system.
– Letting go of the lever will cause the windscreen wash system to stop and the wiper
to continue for another 2 - 3 wiper strokes (depending on the period of spraying of
the windscreen). The lever will stay in position after releasing it .
Switching windscreen wipers off
– Move the lever back into its home position .
After the windscreen wiper switches off each time or the ignition switches off for the
third time, the position of the windscreen wiper changes, this counteracts an early
fatigue of the wiper rubbers.
Fig. 57 Windscreen wiper lever
A4A
1
A
A
A
2
A3A
5
A
1
A
A
A
6
A
7
A
6
A
0
sgg.6.book Page 63 Thursday, September 24, 2009 2:32 PM
Lights and Visibility64
The windscreen wipers and the wash system only operate if the ignition is switched on
and the bonnet is closed 9).
If the intermittent wipe is switched on, the intervals are also controlled depending on
speed.
The rain sensor* automatically regulates the break between the individual wiper
strokes depending on the intensity of the rain.
The rear window will be wiped again if the front window wipers are on when reverse
gear is selected.
The windscreen washer nozzles are heated* when the ignition is switched on.
Top up with wash liquid ⇒ page 214.
Winter position
If the windscreen wipers are in rest position, they cannot be folded out from the windscreen. For this reason we recommend adjusting the windscreen wipers in winter so
that they can be folded out from the windscreen easily. You can set this rest position as
follows:
• Switch on the windscreen wipers.
• Switch off the ignition. The windscreen wipers remain in the position in which they
were when switching off the ignition.
You can also use the service position ⇒ page 65 as a winter position.
WARNING
• Properly maintained windscreen wiper blades are essential for clear visi-
bility and safe driving ⇒ page 65.
• Do not use the windscreen washer system at low temperatures, without
heating the windscreen beforehand. Otherwise the window cleaner could
freeze on the windscreen and restrict the view to the front.
• The rain sensor only operates as a support. The driver is not released from
the responsibility to set the function of the windscreen wipers manually
depending on the visibility conditions.
Caution
In frosty weather, please first of all check whether the windscreen wiper blades are not
frozen to the windscreen before switching them on. Switching on windscreen wipers
when the blades are frozen to the windscreen may result in damage both to the blades
and the motor of the windscreen wipers!
Note
• If the slower or the faster wiper setting is switched on ⇒ page 63, fig. 57 and
the vehicle speed decreases to below 4 km/h, the lower wiper step is switched on
automatically. At a speed increase of more than 8 km/h the previous wiper setting is
established again.
• If there is an obstacle on the windscreen, the wiper will try to push away the
obstacle. If the obstacle continues to block the wiper, the wiper stops after 5 cycles, in
order to avoid a damage to the wiper. Remove the obstacle and and switch on the
wiper again.
Automatic rear window wiper*
If the windshield wiper lever is in the position or , the rear window wiper carries
out a wiping process every 30 seconds or 10 seconds at a speed above 5 km/h.
When the rain sensor* is active (the lever is in the position ) the function is only
active if the front window wipers continue to operate (no break between each wiping
process).
Activation/deactivation
The function of the automatic rear window wiper is activated/deactivated in the information display* in the menu:
Setup
Lights & Vision (Lights & Vision)
Rear wiper
Note
The function of the automatic rear window wiper is only valid for vehicles which are
equipped with the information display*. The function is activated in the factory.
9)
On vehicles which do not have a contact switch for the bonnet, the windshield wiper and wash
system operates also when the bonnet is opened.
A2A3A2A
3
A
1
sgg.6.book Page 64 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 65
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Alternative park position of the rear window wiper
Each time after switching off the engine for the second time, the wiper blade of the rear
window wiper is tilted when the park position is activated. Thus, the life of the wiper
blade is prolonged.
Activating
– Switch on the ignition - position ⇒ page 109.
– Push the operating level in the position ⇒ page 63, fig. 57 five times in succes-
sion within 5 seconds.
– Switch off the ignition. After switching on the ignition again, the alternative park
position of the rear window wiper is activated.
– For deactivating the alternative park position of the rear window wiper, proceed in
the same way.
Headlight cleaning system*
The headlights are being cleaned after the windscreen has been sprayed for the first
time and fifth time, the low beam or main beam are switched on and the windscreen
wiper lever was held in the position ⇒ page 63, fig. 57 for about 1 second.
The headlight washer nozzles are moved forward out of the bumper by the water pressure for cleaning the headlights.
You should remove stubborn dirt (such as insect residues) from the headlight lenses at
regular intervals, for example when refuelling. Please refer to the following guidelines
⇒ page 196, “The headlight lenses”.
You should remove any snow from the fixtures of the washer nozzles and clear ice in
winter with a de-icing spray in order to ensure proper operation of the cleaning
system.
Replacing wiper blades for the windscreen wipers
One cannot fold out the wiper arms in the rest position from the windscreen. Before
replacing the wiper arms you must put them into the service position.
Service position for changing wiper blades
– Close the bonnet.
– Switch the ignition on and then again off.
– Then press the windscreen wiper lever in the position ⇒ page 63, fig. 57 within
10 seconds - the wiper arms move into the service position.
Taking off the wiper blade
– Fold windscreen wiper arm away from the windscreen.
– Press the locking button, in order to unlock the wiper blade and pull off in the
direction of arrow ⇒ fig. 58.
Attaching a wiper blade
– Push the wiper blade until it locks up to the stop.
– Check whether the wiper blade is correctly attached.
– Fold the windscreen wiper arm back onto the windscreen.
The wiper arms move back into the rest position - after switching on the ignition and
after changing the position of the window wiper lever or when driving at a speed
greater than 6°km/h.
A
2
A6A
5
Fig. 58 Wiper blade for the windscreen
wiper
A
4
sgg.6.book Page 65 Thursday, September 24, 2009 2:32 PM
Lights and Visibility66
Wiper blades in proper condition are essential to obtain good visibility. Wiper blades
should not be allowed to become dirtied by dust, insect remains and preserving wax.
Juddering or smearing of the wiper blades could then be due to wax residues left on
the windscreen by vehicle washing in automatic vehicle wash systems. It is therefore
important to degrease the lips of the wiper blades after every pass through an auto-
matic vehicle wash system.
WARNING
• If the windscreen wipers are handled carelessly, there is a risk of damage to
the windscreen.
• You should clean the wiper blades regularly with a windscreen cleaner in
order to avoid any smears. Clean a wiper blade with a sponge or cloth if it is very
dirty, for example from insect residues.
• Replace the wiper blades once or twice a year for safety reasons. The wiper
blades are available from specialist garages.
Replacing the wiper blade on the rear window wiper
Taking off the wiper blade
– Fold windscreen wiper arm away from the windscreen.
– Press the locking button, in order to unlock the wiper blade and pull off in the
direction of arrow ⇒ fig. 59.
Attaching a wiper blade
– Push the wiper blade until it locks up to the stop.
– Check whether the wiper blade is correctly attached.
– Fold the windscreen wiper arm back onto the windscreen.
The same remarks apply here as for ⇒ page 65.
Rear-view mirror
Manual dimming interior rear-view mirror
Basic setting
– Pull the lever on the bottom edge of the mirror forward.
Dimming mirror
– Pull the lever on the bottom edge of the mirror back.
Automatic dimming interior rear-view mirror*
Switching on the automatic dimming
– Press the button - the warning light lights up ⇒ fig. 60.
Fig. 59 Wiper blade for rear window
Fig. 60 Automatic dimming interior
rear- view mirro r
ABA
A
sgg.6.book Page 66 Thursday, September 24, 2009 2:32 PM
Lights and Visibility 67
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Switching off the automatic dimming
– Press again the button - the warning light goes out .
If the automatic dimming is switched on, the mirror dims automatically depending on
the light striking the mirror from the rear. The mirror has no lever on the bottom edge
of the mirror. When the interior lights are switched on or the reverse gear is engaged,
the mirror always moves back into the basic position.
Note
• Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.
• If you switch off the automatic dimming interior rear-view mirror, also the exterior
mirror dimming is switched off.
Exterior mirror
You can adjust the exterior mirrors electrically.
The exterior mirror heater* only operates when the engine is running and up to an
outside temperature of +20°C.
Heating of the external mirror*
– Turn the rotary knob to position ⇒ fig. 61.
Adjusting left and right exterior mirrors simultaneously
– Turn the rotary knob to position . The movement of the mirror surface is identical
to the movement of the rotary knob.
Adjusting the right-hand exterior mirror
– Turn the rotary knob to position . The movement of the mirror surface is identical
to the movement of the rotary knob.
Switching off operating control
– Turn the rotary knob to position .
Tilting surface of front passenger exterior mirror*
When the rotary knob is in position ⇒ fig. 61 and the reverse gear is engaged, the
surface of the mirror tilts down slightly. This provides an aid in seeing the kerb of the
pavement when parking the car.
The mirror returns into its initial position, after the rotary knob is moved out of the
position and put into another position or if the speed is more than 15 km/h.
Memory for exterior mirrors*
On vehicles fitted with a memory for the driver seat, the relevant setting of the exterior
mirror is also stored automatically when the seat position is stored ⇒ page 70.
WARNING
• Convex (curved outward) or spherical (differently curved) exterior mirrors
increase the vision field. They do, however, make objects appear smaller in the
mirror. These mirrors are only of limited use, therefore, for estimating distances
to the following vehicles.
• Use whenever possible the interior rear mirror, for estimating the distances
to the following vehicles.
Note
• Do not touch the surfaces of the exterior mirrors if the exterior mirror heater is
switched on.
ABA
A
Fig. 61 Inner part of door: Rotary knob
sgg.6.book Page 67 Thursday, September 24, 2009 2:32 PM
Lights and Visibility68
• You can set the exterior mirrors by hand, if the power setting function fails at any
time by pressing on the edge of the mirror surface.
• Contact your specialist garage if a fault exists with the power setting of the exterior
mirrors.
Automatic dimming exterior mirror*
The exterior mirrors are dimmed together with the interior mirror. If the automatic
dimming is switched on, the mirror dims automatically depending on the light
striking the mirror from the rear.
When the interior lights are switched on or the reverse gear is engaged, the mirror
always moves back into the basic position (not dimmed).
Note
• Automatic mirror dimming operates only properly if the sun screen* for the rear
window is not in use or the light striking the rear of the interior rear-view mirror is not
affected by other objects.
• Do not affix any stickers in front of the light sensor, so that you do not impair the
automatic dimming function or put it out of operation.
• If you switch off the automatic dimming interior rear-view mirror, also the exterior
mirror dimming is switched off.
sgg.6.book Page 68 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 69
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Seats and Stowage
Front seats
Basic information
The front seats have a wide range of different settings and can thus be matched to the
physical characteristics of the driver and front passenger. Correct adjustment of the
seats is particularly important for:
• safely and quickly reaching the controls;
• a relaxed, fatigue-free body position;
• achieving the maximum protection offered by the seat belts and the airbag
system.
WARNING
• Never transport more occupants than the maximum seating in the vehicle.
• Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened ⇒ page 156, “Transporting children safely” with a
suitable restraint system.
• The front seats and the head restraints must always be adjusted to match
the body size of the seat occupant as well as the seat belts must always be
correctly fastened in order to provide an optimal protection for you and your
occupants.
• Always keep your feet in the footwell when the vehicle is being driven -
never place your feet on the instrument panel, out of the window or on the
surfaces of the seats. This is particularly important for the front seat passenger.
You will be exposed to increased risk of injury if it becomes necessary to apply
the brake or in the event of an accident. If an airbag is deployed, you may suffer
fatal injuries when adopting an incorrect seated position!
• It is impor tant for the driver and front passenger to maintain a distance of at
least 25 cm from the steering wheel or dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to properly
protect you - hazard! The front seats and the head restraints must always also
be correctly adjusted to match the body size of the occupant.
• Ensure that there are no objects in the footwell as any objects may get
behind the pedals during a driving or braking manoeuvre. You would then no
longer be able to operate the clutch, to brake or accelerate.
• Do not transport any objects on the front passenger seat except those
provided for this purpose (e.g. child safety seat) - risk of accident!
Adjusting the front seats
Adjusting a seat in a forward/back direction
–Pull the lever ⇒ fig. 62 up and push the seat into the desired position.
– Release the lever and push the seat further until the lock is heard to engage.
Adjusting height of seat
– Lift the seat if required by pulling or pumping lever upwards.
– Lower the seat if required by pushing or pumping lever downwards.
Adjust the angle of the seat backrest
– Relieve any pressure on the seat backrest (do not lean on it) and turn the hand-
wheel ⇒ fig. 62 to adjust the desired angle of the backrest.
WARNIN G (continued )
Fig. 62 Controls at seat
A1A
1
A
2
A
2
A
3
sgg.6.book Page 69 Thursday, September 24, 2009 2:32 PM
Seats and Stowage70
Adjusting lumbar support*
– Pull on the lever until you have set the most comfortable curvature of the seat
upholstery in the area of your spine.
The driver's seat should be adjusted in such a way that the peda ls can be fully pressed
to the floor with slightly bent legs.
The seat backrest on the driver's seat should be adjusted in such a way that the upper
point of the steering wheel can be easily reached with slightly bent arms.
WARNING
• Only adjust the driver seat when the vehicle is stationary - risk of injury!
• Take care when adjusting the seat! Adjusting the seat without care can lead
to bruises or injuries.
• The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the seat belts and of the airbag system - risk
of injury!
Adjusting front seats electrically*
Adjusting seats
Fig. 63 Side view: Controls for adjusting the seat / seat setting switch
Adopt the correct seated position before setting ⇒ page 69.
Adjusting a seat in a forward/back direction
– Press the switch ⇒ fig. 63 forwards or backwards ⇒ fig. 63.
Set the height of the seat cushion
– Press the switch ⇒ fig. 63 upwards or downwards.
Adjust the angle of the seat cushion
– Press the switch at the front ⇒ fig. 63 or at the back ⇒ fig. 63.
Adjusting the seat backrest
– Press the switch ⇒ fig. 63 in the direction of the desired setting.
Adjusting lumbar support
– Press the switch front ⇒ fig. 63 in order to enlarge the curvature of the lumbar
support.
– Press the switch rear in order to reduce the curvature of the lumbar support.
– Press the switch top in order to adjust the curvature of the lumbar support
higher.
– Press the switch bottom in order to adjust the curvature of the lumbar support
lower.
Switch is operated in order to move the seat up/down and forward/back, while
switch is operated in order to move the backrest forward or back.
WARNING
• Only adjust the driver seat when the vehicle is stationary - risk of injury!
• Caution when adjusting the seat! You may suffer injuries or bruises as a
result of adjusting the seat without paying proper attention.
• In view of the fact that the seats can also be adjusted when the ignition is
switched off (even when ignition key withdrawn), you should never leave children unattended in the vehicle.
A4ABA1A
B
ABA2A
3
A
C
AAA
A
AAAAA
B
A
C
sgg.6.book Page 70 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 71
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
• The seat backrests must not be angled too far back when driving otherwise
this will affect proper operation of the seat belts and of the airbag system - risk
of injury!
Note
If the movement of the seat is inadvertently interrupted during an adjustment, once
again press the switch in the appropriate direction and continue with the adjustment
of the seat to the end.
Storing setting
Storing seat and exterior mirror settings for driving forward
– Switch on the ignition.
– Adjust the seat ⇒ page 70.
– Adjust both exterior mirrors ⇒ page 67.
– Press button SET ⇒ fig. 64.
– Press one of the memory buttons within 10 seconds after pressing the button
SET - an acknowledgement signal confirms that the seat setting is stored.
Storing exterior mirror setting for reversing*
– Switch on the ignition.
– Turn the exterior mirror control to position ⇒ page 67.
– Engage the reverse gear.
– Move the right exterior mirror into the desired position ⇒ page 67.
– Take the vehicle out of gear. The set position of the exterior mirror is stored.
Memory buttons
Memory for the seat offers the possibility to store the individual driver seat and
external mirror position. An individual position can be allocated to each of the three
memory buttons ⇒ fig. 64, that is three in total. After pressing the corresponding
memory button , the seat and the exterior mirror are automatically moved into the
positions which have been allocated to this button ⇒ page 71.
Emergency Off
You can interrupt the setting operation at any time, if you operate any button of the
driver seat.
Note
• For safety reasons, it is not possible to store this position if the inclination angle of
the seat backrest is more than 102° in relation to the seat cushion.
• When storing settings with the memory buttons, we recommend that you begin
with the front button and assign a memory button to each additional driver.
• Each new setting stored with the same button erases the previous setting.
• Each time you store the seat and exterior mirror settings for driving forward you
also have to re-store the individual setting of the exterior mirror on the passenger side
for reversing.
Assigning remote control to the memory buttons
After storing the settings of the seat and exterior mirrors, you have 10 seconds in order
to assign the radio remote control to the appropriate memory button.
– Withdraw the ignition key.
WARNIN G (continued )
Fig. 64 Driver seat: Memory buttons and
SET button
A
A
ABABA
B
sgg.6.book Page 71 Thursday, September 24, 2009 2:32 PM
Seats and Stowage72
– Press the unlock button ⇒ page 45, after the successful assignment an audible
signal will sound. The setting is stored with the memory button which you have
selected.
If you wish to be able to retrieve the settings which are stored in the memory by also
using the radio remote control, you have to assign the radio remote control to a
memory button in each case.
If you wish, you can obtain an additional remote control key from a specialist garage
and then assign the remote control key to another memory button.
Note
• If the radio remote control had previously been assigned to another memory
button, this setting is then erased by the new assignment.
• If you assign the radio remote control to a memory button which has already been
assigned to a radio remote control, the old assignment is also replaced by a new
assignment in this case.
• The assignment of the radio remote control to a memory button is retained,
however, after reassigning the seats and exterior mirrors.
Retrieving settings of the seat and mirrors
You can retrieve the stored settings either with the memory buttons or
with the remote control*.
Retrieving settings with memory buttons
– In order to retrieve the stored setting, you have two possibilities:
– By press ing briefly: briefly press the desired memory button ⇒ page 71,
fig. 64. The seat and exterior mirror are moved automatically into the stored posi-
tions (this applies only if the ignition is switched on and the speed is less than 5
km/h).
– By pressing for a long period of time: press and hold the desired memory button
pressed long enough until the seat and the exterior mirrors are moved into the
stored positions.
Retrieving settings with remote control
– If the driver door is closed and the ignition is switched off, briefly press the unlock
button of the radio remote control ⇒ page 45 and then open the driver door.
– The seat and exterior mirrors now move automatically into the stored positions.
Retrieving setting of exterior mirror for reversing*
– Turn the rotary knob for the exterior mirror setting into the position ⇒ page 67
before engaging the reverse gear.
The mirror returns into its initial position, after the rotary knob is moved out of the
position and put into another position or if the speed is more than 15 km/h.
Emergency Off
You can interrupt the setting operation at any time, if you operate any button of the
driver seat.
Head restraints
Fig. 65 Adjusting head restraint / pulling out
Best protection is achieved if the top edge of the head restraint is at the same level as
the upper part of your head.
Adjusting the height of a head restraint
– Grasp the side of the head restraint with both hands and push the head restraint up
or down in direction of arrow ⇒ fig. 65.
ABA
B
A
1
sgg.6.book Page 72 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 73
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– Move the head restraint downwards if required by pressing the locking button with
one hand in direction of arrow ⇒ fig. 65 and by pressing with the other hand
the head restraint downwards.
Removing and installing a head restraint
– Pull the head restraint out of the seat backrest as far as the stop.
– Press the locking button in the direction of arrow ⇒ page 72, fig. 65 and pull the
head restraint out.
– To re-insert the head restraint, push it down into the seat backrest far enough until
you hear the locking button engage.
The position of the front and rear outer head restraints is adjustable in height. The
middle rear head restraint is adjustable in two positions.
The head restraint s must be adjusted to match the size of the seat occupant. Correctly
adjusted head restraints together with the seat belts offer effective protection for the
occupants ⇒ page 138, “Correct seated position”.
WARNING
• The head re straints must be correctl y adjusted in order to offer effective
protection for the occupants in the event of an accident.
• Do not drive under any c ircumstance with removed head restraints - risk of
injury!
• If the rear seats are occupied, the rear head restraint must not be in the
lower position.
Middle rear head restraint*
IIn certain countries national legal provisions also require the equipment of the rear
seat with fixing eyes for child seat using the “Top Tether” system ⇒ page 162. For vehi-
cles, which are equipped with such fixing eyes, a deviating sequence for removing the
middle head restraint must be observed.
Removing and installing the rear middle head restraint
– Pull the head restraint out of the seat backrest as far as the stop.
– Press the locking button in the direction of arrow ⇒ fig. 66 and pull the head
restraint out.
– To re-insert the head restraint, push it down into the seat backrest far enough until
you hear the locking button engage.
WARNING
• The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.
• Do not dri ve under any circumst ance with rem oved he ad restrai nts - risk of
injury!
• If the rear seats are occupied, the rear head restraint must not be in the
lower position.
A
2
Fig. 66 Rear seats: middle head restraint
sgg.6.book Page 73 Thursday, September 24, 2009 2:32 PM
Seats and Stowage74
Rear seats
Adjusting seats in forward/back direction
Fig. 67 Releasing at the front / rear
To enlarge the luggage compartment, the outer rear seats can be pushed forwards,
folded fully forwards or the seats can be removed.
Moving seats in forward/back direction
– Pull the lever ⇒ fig. 67 up in direction of arrow or on the release loop in
direction of arrow ⇒ fig. 67 and move the seat into the desired position .
Note
Please refer to the following guidelines ⇒ page 139, “Correct seated position for the
occupants on the rear seats”.
Adjusting the seat backrest
Adjust the angle of the seat backrest
– Pull the lever ⇒ fig. 68 and adjust the desired angle of the seat backrest.
Folding rear seats forwards
Fig. 69 Fold seat forward / secure folded forward seats
Folding rear seats fully forwards and secure
– Open the guide loop for the seat belt on the side of the outer seats and put the belt
tongue into the opening of the wheel housing on the respective side trim panel safety holder.
– Remove the head restraint from the rear middle seat ⇒ page 73.
– Move the rear exterior seats as far as possible to the rear ⇒ page 74.
AAA1A2A
3
Fig. 68 Adjusting the seat backrest
sgg.6.book Page 74 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 75
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– Pull on the levers ⇒ page 74, fig. 68 and fold the seat backrests of the rear exterior
seats onto the seat cushion as far as the stop.
– Fold the middle rear seat backrest forwards in the same way, then pull once more
on the lever ⇒ page 74, fig. 68 and press the seat backrest downwards until it is
heard to lock into a lower position.
– Pull the lever ⇒ page 74, fig. 69 up and then fold the seat fully forwards.
– Secure the folded forward seat with the aid of the fixing belt to a guide rod of
the head restraint for the front seat ⇒ page 74, fig. 69.
WARNING
• Immediately secure the folded forward seat with the aid of the fixing belt to
a guide rod of the head restraint for the front seat - there is a risk of injury as
soon as the vehicle starts off.
• If the seat is not in the rear end position, damage can occur to the locking
bolts if the seat is unlocked.
Caution
Make sure that the storage compartment, the ashtray and the cup holder in the rear
part of the centre console are closed (otherwise these could get damaged) before
folding forward the rear middle seat.
Note
Please refer to the following guidelines ⇒ page 138, “Correct seated position for the
driver”.
Removing seats
Fig. 70 Unlocking the folded forward seat / carrying handles on the seat cushion
Unlocking and removing seats
– Unlock the folded forward seat by pressing the seat locks in direction of arrow
⇒ fig. 70.
– Remove the seat by way of the carrying handles on the seat cushion and
⇒ fig. 70.
Note
The outer seats are not replaceable alternatively. In the rear area the left seat is marked
with the letter L and the right seat with the letter R.
Note
Please refer to the following guidelines ⇒ page 139, “Correct seated position for the
occupants on the rear seats”.
ABA1AAA
B
sgg.6.book Page 75 Thursday, September 24, 2009 2:32 PM
Seats and Stowage76
Adjusting seats in crosswise direction
Moving seats in crosswise direction
– Remove the middle seat ⇒ page 75.
– Fold the outer seat forwards ⇒ page 74 and lock it ⇒ page 75, fig. 70.
– Move the folded forward and unlocked seat on the guide towards the middle of the
vehicle up to the stop.
– Lock the seat at the end of the guide ⇒ fig. 71.
Move seats into the initial position
Locking seats and folding back into position
– If the seat is removed, first of all position it on the guid e and lock the seat ⇒ fig. 71.
Check for yourself that the seat is correctly locked by pulling it up.
– Fold the seat into the horizontal position until it is heard to lock. Check for yourself
that the seat can no longer be lifted by pulling it up.
– Push the lever ⇒ fig. 72 and fold the backrest back into position. Check for yourself
that the seat backrest is engaged.
– Take the belt tongue out of the safety holder.
– Close the guide loop of the seat belt on the side of the outer seats until it is heard
to lock.
WARNING
• The belt locks and the belts must be in their original position after folding
back the seat cushions and the seat backrests - they must be ready to use.
• The seat backrests must be securely interlocked in position so that no
objects in the luggage compartment can slide into the passenger compartment
if there is sudden braking - risk of injury!
• When folding the seat backrest always make sure that it has safely locked
into position, this is confirmed by the position and a visible marking on the
cover of the lever.
Note
The seat belts of the outer seats must always be guided through the guide loops next
to the head restraints. Otherwise the seat belts can slip behind the seat.
Folding table on the middle seat backrest*
Fig. 71 Locking the seat
Fig. 72 Folding the seat backrest back
into position
Fig. 73 Rear seats: Armrest
sgg.6.book Page 76 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 77
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– The middle seat backrest can be folded ⇒ page 74, “Folding rear seats forwards”
forwards and used as armrest or table with cup holder ⇒ page 76, fig. 73.
– You can place two cups or beverage cans into the recesses.
Note
If the middle rear seat backrest should be folded forward for lengthy periods, then
make sure that the belt locks are not located below it - this can result in permanent
damage to the upholstery.
Seat heating of the front seats*
You can electrically heat the seat cushions and the seat backrests of the front seats.
Front seats
– You can switch on and regulate the seat heating of the driver or front passenger
seat by pressing the surface of the regulator at the point at which the symbol is
located ⇒ fig. 74.
– With one press, you can switch the heating to highest intensity which is indicated
by the lighting up of the three warning lights in the switch.
– With repeated pressing of the switch, the intensity of the heating is down-regulated
up to the switch-off. The intensity of the heating is indicated by the number of illuminated warning lights in the switch.
WARNING
If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g.
through medication, paralysis or because of chronic illness (e.g. diabetes), we
recommend not to use the seat heating. This can lead to burns on the back, the
posterior and the legs which are difficult to heal. If the seat heating is used, we
recommend to make regular breaks in your journey when driving long
distances, so that in specific cases as mentioned above the body can recuperate
from the stress of the journey. Please consult your doctor, who can evaluate
your specific condition.
Caution
• You should not kneel on the seats or otherwise apply pressure at specific points in
order to avoid damaging the heating elements of the seat heaters.
• Do not use the seat heating if the seats are not occupied by persons or if objects
are fastened or stored on them, for example a child seat, a bag etc. A fault of the heating
elements in the seat heating can occur.
• Do not clean the seats moist ⇒ page 197.
Note
• The seat heating should only be switched on when the engine is running. This has
a significant effect of saving on the battery capacity.
• If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control.
Pedals
Concerning a secure depressing of the pedal, you should use only footmats from the
Škoda genuine accessories.
Operation of the pedals must not be hindered!
WARNING
• Greater pedal distances may be needed when there is a fault in the brake
system.
Fig. 74 Dash panel: Regulator for front
seat heating
sgg.6.book Page 77 Thursday, September 24, 2009 2:32 PM
Seats and Stowage78
• Do not place any footmats or other additional floor coverings in the area of
the pedals in order to ensure that all the pedals can be fully depressed and are
able to return unobstructed to their initial position - risk of accident!
• There must be no objects on the floor which could roll under the pedals. You
woul d then n o longe r be abl e to app ly the brakes, operate the clutch or accelerator - risk of accident!
Luggage compartment
Loading the luggage compartment
Please observe the following in the interest of having good handling characteristics of
your vehicle:
– Distribute the items of luggage as evenly as possible.
– Place heavy objects as far forward as possible.
– Attach the items of luggage to the lashing eyes or the fixing net* ⇒ page 79.
In the event of an accident, there is such a high kinetic energy which is produced by
small and light objects that they can cause severe injuries. The magnitude of the kinetic
energy depends on the speed at which the vehicle is travelling and on the weigh t of the
object. The speed at which the vehicle is travelling is in this case the more significant
factor.
Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object
with a weight of 4.5 kg produces an energy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg. You can imagine the injuries that can occur, if this “bullet” is flying through the interior compartment and hits
an occupant.
WARNING
• Store the objects in the luggage compartment and attach them to the
lashing eyes, e.g. with the fixing nets.
• Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an accident and can injure the occupants or
other oncoming traffic. This risk is still increased, if the objects which are flying
around are hit by a deployed airbag. In this case, the objects which are thrown
back can injure the occupants - hazard.
• Please note that the handling properties of your vehicle may be affected
when transporting heavy objects as a result of the displacement of the centre of
gravity. The speed and style of driving must be adjusted accordingly.
• The items carried in the luggage compartment should be stowed in such a
way that no objects are able to slip forward if there are any sudden driving or
braking manoeuvres undertaken - risk of injury!
• Never drive with the boot lid fully opened or slightly ajar otherwise exhaust
gases may get into the interior of the vehicle - risk of poisoning!
• On no account exceed the permissible axle loads and the permissible gross
weight of the vehicle - risk of accident!
• Never transport occupants in the luggage compartment!
Caution
Please ensure that the heating elements of the rear window heater are not damaged
as a result of objects sliding in this area.
Note
Tyre pressure must be adjusted to the load ⇒ page 215.
WARNIN G (continued ) WARNIN G (continued )
sgg.6.book Page 78 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 79
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Fastening elements
Fig. 75 Luggage compartment: Lashing eyes and fastening elements / attachment points and
fasteni ng strip
Fixing eyes and fastening elements ⇒ fig. 75 on the left and fixing eyes and a fastening
strip* ⇒ fig. 75 on the right are fitted on both sides of the luggage compartment.
You can also attach the fixing nets*, for stowing small items of luggage, in the luggage
compartment on the fixing eyes and fastening elements or on the fixing eyes and the
fastening strip with integrated hook ⇒ fig. 75.
The fixing nets* and the installation instruction are located in the luggage compartment.
WARNING
• The load to be transported must be fixed in place in such a way that it cannot
move during the journey and when braking.
• If the items of luggage or objects are attached to the lashing eyes with
unsuitable or damaged lashing straps, injuries can occur in the event of braking
manoeuvres or accidents. In order to prevent the items of luggage being thrown
forward, always use suitable lashing straps which are firmly attached to the
lashing eyes.
Folding hooks
Folding hooks for attaching small items of luggage, such as bags etc., are provided on
both sides of the luggage compartment ⇒ fig. 76.
An item of luggage weighing up to 7.5 kg can be attached to the hook.
WARNING
Please refer to the following guidelines ⇒ page 78.
Fastening strip with moveable hook*
Fig. 77 Luggage compartment: Fastening strip with moveable hook / remove hook
A fastening strip is located on both sides of the luggage compartment with two moveable hooks each, in order to attach small items of luggage, such as bags etc. ⇒ fig. 77.
An item of luggage weighing up to 7.5 kg can be attached to each hook.
Fig. 76 Luggage compartment: folding
hooks
sgg.6.book Page 79 Thursday, September 24, 2009 2:32 PM
Seats and Stowage80
Move the hook into another position
– Fold up the hook in direction of arrow until an angle of 45° is reached
⇒ page 79, fig. 77.
– Move the hook in direction of arrow into the desired position and fold down the
hook as far as the stop in direction of arrow ⇒ page 79, fig. 77.
Remove the hook from the fastening strip
– Fold the hook in direction of arrow until it slackens.
Install the hook on the fastening strip
– Position the hook on the fastening strip in the vertical position in direction of arrow
and lightly press it on.
– Fold the hook down in opposite direction of the arrow until it locks fully.
WARNING
Please refer to the following guidelines ⇒ page 78.
Fixing nets - Net programme*
Fig. 78 Fixing net: double horizontal pocket, floor fixing net / double ver tical pockets
Fixing examples of the fixing net as double horizontal pocket, floor fixing net ⇒ fig. 78
on the left and double vertical pocket ⇒ fig. 78 on the right.
The fixing nets* and the installation instruction are located in the luggage compartment.
WARNING
• The whole strength of the net makes it possible to load the pocket with
objects of up to 3.5 kg in weight. Heavy objects are not secured sufficiently - risk
of injury and net damage!
• The load to be transported must be fixed in place in such a way that it cannot
move during the journey and when braking.
Caution
Do not place any objects with sharp edges in the nets - risk of net damage.
The luggage compartment cover
You can use the luggage compartment cover behind the head
restraints for storing light and soft items.
The luggage compartment cover can be removed as required if one must transport
bulky goods.
Removing the luggage compartment cover
– Fold the seat backrests a little forward in order to facilitate the removal of the
luggage compartment cover.
– Unhook the support straps on the boot lid ⇒ fig. 79.
A1A2A
3
A4A
5
A
4
Fig. 79 Removing the luggage compartment cover
A
1
sgg.6.book Page 80 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 81
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
– Place the cover in the horizontal position.
– Pull the luggage compartment cover out of the holders to the rear or press on
the bottom side of the luggage compartment cover in the front area.
– Fold the slackened front part of the luggage compartment cover over the head
restraints of the rear seats.
– Slightly tilt the luggage compartment cover and remove it to the rear.
– Install again by pushing the luggage compartment cover forwards into the holder
and hanging the support straps on the boot lid.
You can stow the removed luggage compartment cover behind the rear seat backrest.
The procedure of installing or removing is identical.
The luggage compartment cover is foreseen for storage of small objects of up to 2.5 kg.
in weight.
WARNING
No objects should be placed on the luggage compartment cover, the vehicle
occupants could be endangered if there is sudden braking or the vehicle
collides with something.
Caution
Please ensure that the heating elements of the rear window heater are not damaged
as a result of objects placed in this area.
Static separation net*
Fig. 80 Use of the static separation net behind the rear seats / behind the front seats
Install the static separation net behind the front seats or the rear seats.
Installing the static separation net
– Remove the luggage compartment cover ⇒ page 80.
– Take the separation net out of the bag.
– Unfold both parts of the cross rod until they are heard to engage.
– Insert the cross rod into the mount first on the one side and push the cross rod
forward. In the same way, fix the cross rod to the other side of the vehicle, mount
⇒ fig. 80.
– Hang the carabines at the ends of the strap into the fixing eyes behind the rear
or front seats.
– Pull the strap through the tensioning clasp, first of all on the one side and then on
the other side.
Remove the static separation net behind the rear seats
– Slacken the bands on both sides and take off the carabines ⇒ fig. 80.
– Push the cross rod first of all on the one side and then on the other side towards
the rear.
– Take the cross rod out of the mounts .
A2A2A1A
B
A
B
ACA
C
A
B
sgg.6.book Page 81 Thursday, September 24, 2009 2:32 PM
Seats and Stowage82
Pack static separation net
– Press the red button of the joint - so that it releases.
– Put the separation net folded together in the bag and close it.
– Attach the bag with the aid of the plastic carabines to the eyes on the left and right
luggage compartment trim panel.
Installing and removing the static separation net behind the rear seats with variable
loading floor* ⇒ page 82 is carried out analogously as behind the rear seats without
variable loading floor. Use the lower fixing eyes on the carrier rails in order to attach
the carabines.
The opening ⇒ page 81, fig. 80 in the static separation net is designed to feed
through the three-point seat belt ⇒ page 144.
Variable loading floor*
Remove variable loading floor
Fig. 81 Luggage compartment: fold up variable loading floor / remove variable loading floor
The variable loading floor makes it easier to handle bulky goods and creates an even
luggage compartment floor when the rear seat backrests are folded forward. The
maximum permissable surface load of the variable loading floor is 75 kg.
Remove variable loading floor
– You can fold together the loading floor by moving in direction of arrow
⇒ fig. 81.
– Raise the floor in direction of arrow ⇒ fig. 81.
– Pull on both sides of the locking levers in direction of arrow ⇒ fig. 81.
– Pull the loading floor up and out in direction of arrow .
– The installation of the variable loading floor is carried out in the reverse order.
Secure the variable loading floor in the raised position
– Fold up the hooks on the fastening strip in direction of arrow ⇒ page 79, fig. 77.
– Fold up the variable loading floor behind the seat backrests of the rear seats.
– Fold down the hooks in direction of arrow as far as the stop ⇒ page 79, fig. 77.
– Support the variable loading floor on the hooks folded downwards.
WARNING
Pay attention when installing that the carrier rails and the variable loading floor
are correctly fixed, otherwise the occupants are at risk.
Note
If the variable loading floor* is installed, no flexible storage compartment can be
installed.
AAADA1A
2
A
3
A4A
1
A
3
sgg.6.book Page 82 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 83
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Remove carrier rails
Fig. 82 Luggage compartment: Slacken check points / remove carrier rails
Install carrier rails
– Slacken the check points on the car rier rails using the vehicle key or a flat screw-
driver ⇒ fig. 82.
– Grasp the carrier rail at the position ⇒ fig. 82 and slacken it by pulling in the
direction of arrow.
– Grasp the carrier rail at the position , slacken it by pulling in the direction of
arrow and take it out.
– The carrier rail on the other side of the luggage compartment can be removed in
the same way.
Install carrier rails
– Position the carrier rails on the sides of the luggage compartment.
– Press both check points on each carrier rail up to the stop.
– Check the attachment of the carrier rails by pulling it.
WARNING
Pay attention when installing that the carrier rails are correctly fixed, otherwise
the occupants are at risk.
Variable loading floor* with spare wheel*
Use variable loading floor
Fig. 83 Luggage compartment: Fold the side parts of the loading floor / example for using the
variable loading floor
The variable loading floor makes it easier to handle bulky goods and creates an even
luggage compartment floor when the rear seat backrests are folded forward. The
maximum permissable surface load of the variable loading floor is 75 kg.
You can fold down the side parts of the loading floor in direction arrow in order to
enlarge the space foreseen for stowing items of luggage ⇒ fig. 83.
Note
If the variable loading floor with spare wheel* is installed, no flexible storage compartment can be installed.
• The variable loading floor with spare wheel* can be secured in the raised position
in the same way as the variable loading floor without spare wheel* ⇒ page 82, “Secure
the variable loading floor in the raised position”.
ABAAA1AAA
2
sgg.6.book Page 83 Thursday, September 24, 2009 2:32 PM
Seats and Stowage84
Removeable storage box
The storage box is housed under the variable loading floor. If necessary, you can
remove it.
There is a space for the vehicle tool kit under the storage box ⇒ page 223.
WARNING
The removeable storage box must be located under the loading floor for the
safe use of the variable loading floor.
Roof rack
Roof rail
Pay attention to the following points if you wish to transport luggage or other items on
the roof of your vehicle:
• A special roof luggage rack system was developed for the vehicle, that is why you
should only use a roof luggage rack which has been released for use by Škoda Auto.
• The roof rail is the basis for a complete roof luggage rack system. Separate addi-
tional holders are required for safety reasons for transporting luggage, bikes, surfboards, skis and boats.
• The basic version of the roof luggage rack system and further components are
obtainable as accessories from the specialist garages.
Caution
• Ensure that the opened boot lid does not collide with the roof load.
• On models fitted with a power sliding/tilting roof, ensure that the opened
sliding/tilting roof does not strike any items of luggage transported on the roof.
For the sake of the environment
The increased aerodynamic drag results in a higher fuel consumption.
Roof load
Distribute weight evenly over the roof luggage rack system. The maximum permissible
roof load (including roof rack system) of 75 kg and the maximum permissible total
weight of the vehicle should not be exceeded.
You cannot make full use of the permissible roof load if you use a roof luggage rack
system with a lower load carrying capacity. The load transported on the roof luggage
rack system must not exceed the weight limit which is stated in the fitting instructions.
WARNING
• The items which you transport on the roof bar system must be reliably
attached - risk of accident!
• You must on no account exceed the permissible roof load, the permissible
axle loads and the permissible gross weight of your vehicle - risk of accident!
Fig. 84 Luggage compartment: Storage
box
A
A
Fig. 85 Roof rail
sgg.6.book Page 84 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 85
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
• Please note that the handling properties of your vehicle change when you
transport heavy or bulky items on the roof bar system as a result of the
displacement of the centre of gravity and the increased wind attack area - risk
of accident! You must absolutely adapt your style of driving and the speed of
the vehicle to the specific circumstances.
Cup holder
Cup holder in front centre console
You can place two cups or beverage cans into the recesses ⇒ fig. 86.
WARNING
• Do not place any hot beverages into the cup holder. If the vehicle moves, the
hot beverages may spill - risk of scalding!
• Do not use any cups or beakers which are made of brittle material (e.g. glass,
porcelain). You might be injured by them in the event of an accident.
Caution
Do not open the beverages in the cup holder while driving. They may spill when
braking and while doing so damage the vehicle.
Cup holder in rear centre console*
– Press on the panel in the area ⇒ fig. 87 - the cup holder comes out.
– Pull the cup holder out as far as the stop.
– Adjust the cup holder by moving the locking plate .
WARNING
• Do not place any hot beverages into the cup holder. If the vehicle moves, the
hot beverages may spill - risk of scalding!
• Do not use any cups or beakers which are made of brittle material (e.g. glass,
porcelain). You might be injured by them in the event of an accident.
Caution
The cup holder in the rear part of the centre console must be closed (otherwise it could
get damaged) before folding forward the rear middle seat.
WARNIN G (continued )
Fig. 86 Front centre console: Cup holder
Fig. 87 Centre console at rear: Cup
holder
A
A
A
B
sgg.6.book Page 85 Thursday, September 24, 2009 2:32 PM
Seats and Stowage86
Note holder
The note holder is designed e.g. for attaching a car park ticket in parking areas.
The attached note has to always be remove d before starting off in order not to restrict
the driver's vision.
Ashtray*
Front ashtray
Removing ashtray
– Remove the ashtray ⇒ fig. 89 upwards. When removing do not hold the ashtray at
the cover - risk of breakage.
Replacing ashtray
– Insert the ashtray vertically.
WARNING
Never lay flammable objects in the ashtray basin - risk of fire!
Rear ashtray - low centre console
Opening ashtray
– Grasp the ashtray cover at the lower edge and fold it open in the direction of
arrow ⇒ fig. 90.
Removing ashtray
– Grasp the ashtray at the handle and pull it out in an upward direction.
Replacing ashtray
– Insert the ashtray into the console and press it in.
There is a beverage holder attached to the inner side of the ashtray cover.
WARNING
Never lay flammable objects in the ashtray basin - risk of fire!
Fig. 88 Windscreen: Note holder
Fig. 89 Centre console: Front ashtray
Fig. 90 Low centre console: Rear ashtray
A
A
A
B
sgg.6.book Page 86 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 87
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Caution
The ashtray in the rear part of the centre console must be closed (otherwise it could
get damaged) before folding forward the rear middle seat.
Rear ashtray - high centre console*
Opening ashtray
– Press on the top part of the cover of the ashtray in area ⇒ fig. 91.
Removing ashtray insert
– Press the cover of the ashtray down slightly as far as the stop.
– Grasp the ashtray insert at the cover and pull it out.
Insert ashtray insert
– Insert the ashtray insert into the mount and press it in.
WARNING
Never lay flammable objects in the ashtray basin - risk of fire!
Caution
The ashtray in the rear part of the centre console must be closed (otherwise it could
get damaged) before folding forward the rear middle seat.
Cigarette lighter*, power sockets
Cigarette lighter
You can also use the socket on the cigarette lighter for other electrical
appliances.
Using the cigarette lighter
– Press in the button of the cigarette lighter ⇒ fig. 92.
– Wait until the button jumps forward.
– Remove the cigarette lighter immediately and use it.
– Insert the cigarette lighter again into the socket.
Using the socket
– Remove the cigarette lighter or the cover of the power socket.
– Connect the plug of the electrical appliance to the socket.
The 12 volt power socket can also be used to supply power to additional electrical
accessories with a power uptake up to 120 watts.
WARNING
• Take care when using the cigarette lighter! Not paying proper attention or
incorrect use the cigarette lighter in an uncontrolled manner may result in
burns.
Fig. 91 High centre console: Rear ashtray
AAA
B
Fig. 92 Centre console: Cigarette lighter
sgg.6.book Page 87 Thursday, September 24, 2009 2:32 PM
Seats and Stowage88
• The cigarette lighter and the power socket also operates when the ignition is
switched off or the ignition key withdrawn. You should therefore never leave
children unattended in the vehicle.
Caution
Always use matching plugs to avoid damaging the power socket.
Note
• Connecting electrical components when the engine is not running will drain
the battery of the vehicle - risk of battery draining!
• Further information ⇒ page 221, “Accessories, changes and replacement of
parts”.
Power socket in the luggage compartment
– Open the cover of the power socket ⇒ fig. 93.
– Connect the plug of the electrical appliance to the socket.
You can only use the power socket for the connection of approved electrical accessories with a power uptake up to 1 0 watts. The vehicle battery will be discharged in the
process if the engine is stationary.
The same remarks apply here as for ⇒ page 87.
Further information ⇒ page 221, “Accessories, changes and replacement of parts”.
Storage compartments
Overview
You will find the following storage facilities in your vehicle:
WARNING
• Please do not place anything on top of the dash panel. Such objects might
slide or fall down when driving (when accelerating or cornering) and may
distract you from concentrating on the traffic situation - risk of accident!
• Ensure that when driving no objects from the centre console of from other
storage possibilities may get into the footwell of the driver. You would then no
longer be able to apply the brakes, operate the clutch or accelerator - risk of
accident!
WARNIN G (continued )
Fig. 93 Luggage compartment: Power
socket
Storage compartment on the front passenger side ⇒ page 89
Storage compartment on the dash panel* ⇒ page 89
Storage compartment in front centre console ⇒ page 90
Storage compartment for spectacles* ⇒ page 90
Storage compartment in the front and rear doors ⇒ page 90
Storage compartment below front passenger seat* ⇒ page 91
Front seat armrest with storage compartment* ⇒ page 91
Storage compartment in rear centre console* ⇒ page 92
Storage compartments in the luggage compartment* ⇒ page 92
Flexible storage compartment* ⇒ page 92
Clothes hooks ⇒ page 93
Through-loading bag* ⇒ page 93
sgg.6.book Page 88 Thursday, September 24, 2009 2:32 PM
2
Seats and Stowage 89
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Storage compartment on the front passenger side
Opening and closing the storage compartment on the front passenger
side
– Press the button ⇒ fig. 94 - the lid folds down.
– Raise the lid and press it until the catch is heard to engage.
In the storage compartment are pin holders.
WARNING
The storage compartment must always be closed when driving for safety
reasons.
Cooling of storage compartment on front passenger
side*
The compartment is fitted with an isolatable entry for cooled air.
– You can switch on the cooling system by pulling the lever in direction of arrow
⇒ fig. 95.
– Switch off the cooling system by inserting the lever.
Opening the air inlet when the air conditioning system is on causes fresh or interior air
to flow into the storage compartment.
We recommend that you switch off the cooling if it is operating in the heating mode or
if you are not using the cooling system for the storage compartment.
Storage compartment on the dash panel*
Fig. 94 Dash panel: Storage compartment on the front passenger side
Fig. 95 Storage compartment: Using
cooling system
Fig. 96 Dash panel: Storage compartment
sgg.6.book Page 89 Thursday, September 24, 2009 2:32 PM
Seats and Stowage90
– Press on the button ⇒ page 89, fig. 96 in direction of arrow, the cover then folds
upwards.
Certain model versions are equipped without lid for the storage compartment.
WARNING
• The storage compartment is not a substitute for the ashtray and must also
not be used for such purposes - risk of fire!
• The storage compartment must always be closed when driving for safety
reasons.
• Do not put any highly inflammable objects or objects which are sensitive to
heat (e.g. lighters, sprays, spectacles, carbonated drinks) in the storage
compartment.
Storage compartment in front centre console
The storage compartment without cover in the centre console is foreseen for storage
of small objects.
WARNING
The storage compartment is not a substitute for the ashtray and must also not
be used for such purposes - risk of fire!
Storage compartment for spectacles*
– Press button , the storage compartment folds down ⇒ fig. 98.
WARNING
The compartment must only be opened when removing or inserting the spectacles and otherwise must be kept closed.
Storage compartment in the front and rear doors
A bottle holder is located in the area of the storage compartment for the front and
rear doors.
Fig. 97 Front centre console: Storage
compartment
Fig. 98 Detail of the headliner: Storage
compartment for spectacles
A
A
Fig. 99 Storage compartment in the
front doors
A
B
sgg.6.book Page 90 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 91
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
WARNING
Use the area ⇒ page 90, fig. 99 of the storage compartment only for storing
objects which do not project so that the effectiveness of the side airbag is not
impaired.
Storage compartment below front passenger seat*
The storage compartment is foreseen for storing small objects of up to 1.5 kg in weight.
– Tilt the lock to open the flap and pull out the flap ⇒ fig. 100.
– Tilt the lock to close the flap and press flap close.
Front seat armrest with storage compartment*
Fig. 101 Armrest: Storage compartment / cooling of storage compartment
The armrest is adjustable for height and length.
Opening storage compartment
– Open the lid of the armrest in the direction of arrow ⇒ fig. 101.
Closing storage compartment
– Open the lid up to the stop, then you can fold it downwards.
Setting height
– First of all fold the lid to the bottom and lift it in the direction of arrow into one of
the 4 fixed positions.
Adjusting in forward/back direction
– Push the lid into the desired position.
Opening air inlet
– Pull the lock in upward direction ⇒ fig. 101.
Closing air inlet
– Push the lock as far as the stop downwards.
On vehicles fitted with air conditioning, the storage compartment is equipped with a
lockable inlet for thermally treated (warmed-up) air.
At open air supply, air flows into the storage with a temperature which is as high as the
one out of the air outlet nozzles, depending on temperature setting.
The air inlet in the storage compartment is connected to position through adjustment of the control dial for air distribution. This position causes the maximum amount
of air to flow into the storage compartment (depending on the rotary regulator position for the fan).
You can use the storage compartment, for example, to temper drinks cans, etc.
If you do not use the air inlet in the storage compartment, the end cover should
always be kept closed.
A
A
Fig. 100 Front passenger seat: Storage
compartment
A1A
A
A
A
sgg.6.book Page 91 Thursday, September 24, 2009 2:32 PM
Seats and Stowage92
Note
Push the lid of the armrest up to stop to the rear before operating the handbrake.
Storage compartment in rear centre console*
The storage compartment is equipped with a removeable insert.
– Open the storage compartment by pulling on the upper edge of the storage
compartment in the direction of arrow ⇒ fig. 102.
WARNING
The storage compartment is not a substitute for the ashtray and must also not
be used for such purposes - risk of fire!
Caution
The storage compartment in the rear part of the centre console must be closed (otherwise it could get damaged) before folding forward the rear middle seat.
Storage compartments in the luggage compartment*
Fig. 103 Luggage compartment: Storage compartments
Storage compartments are located on both sides of the luggage compartment.
The removeable storage compartment on the left side ⇒ fig. 103 is suitable for
stowing small objects weighing up to 1.5 kg.
The storage compartment on the right side ⇒ fig. 103 is suitable for stowing small
objects weighing up to 0.5 kg.
Flexible storage compartment*
A flexible storage compartment is located on the right side of the luggage compartment. The flexible storage compartment is foreseen for storing small objects of up to 8
kg in weight.
Fig. 102 Centre console at rear: Storage
compartment
AAA
A
A
B
Fig. 104 Flexible storage compartment
sgg.6.book Page 92 Thursday, September 24, 2009 2:32 PM
Seats and Stowage 93
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Removing
– Take hold of the flexible storage compartment at both upper corners.
– Press the upper corners to the inside and release the storage compartment by
pulling upwards.
– Remove by pulling towards you.
Installing
– Insert both ends of the flexible storage compartment into the openings of the right
side trim panel of the luggage compartment and push it downwards until it locks.
Clothes hooks
The clothes hooks are located on the middle pillar and on the handle of the headliner
above each of the rear doors.
WARNING
• Ensure that any clothes hanging from the hooks do not impair your vision to
the rear.
• Use the hooks for hanging only light items of clothing and ensure that there
are no heavy or sharp-edged objects in the pockets.
• The maximum permissable load of the hooks is 2 kg.
• Do not use clothes hangers for hanging up items of clothing otherwise this
will interfere with the protection offered by the head airbag*.
Removeable through-loading bag*
The removeable through-loading bag is solely used for transporting
skis.
The removeable through-loading bag is foreseen for two pairs of skis. The total weight
of the skis which are transported must not exceed 10 kg.
Load ing
– Open a rear side door of the vehicle.
– Fold the backrest of the middle seat forwards ⇒ page 74.
– Place the empty removeable through-loading bag in the gap between the front and
rear seats in such a way that the end of the bag with the zip lies in the luggage
compartment.
– Open the boot lid.
– Push the skis into the removeable through-loading bag from the luggage compart-
ment ⇒ .
– Close the removeable through-loading bag with the zip.
Securing
– Pull the securing belt with both lock tongues out of the pocket of the removeable
through-loading bag.
– Insert the lock tongues in the belt locks of the rear middle seat belt , first of
all on the one side and then on the other side ⇒ fig. 105.
Fig. 105 Securing the removeable
through-loading bag
AAA
C
sgg.6.book Page 93 Thursday, September 24, 2009 2:32 PM
Seats and Stowage94
– Place the securing belt in the middle of the skis between the heel and the tip of the
bindings and pull the securing belt tight at the free end of the belt .
Stowing
– Carefully fold the empty (dry) removeable through-loading bag together, place it in
the luggage compartment and secure it to prevent it slipping.
WARNING
• After placing the skis into the removeable through-loading bag, you must
secure it with the securing belt .
• The securing belt must hold the skis tight.
• Ensure that the securing belt for skis grasps the middle between the tip and
the heel element of the binding (see also imprint on the removeable throughloading bag).
Note
• You must put the skis and the sticks in the removeable through-loading bag with
the tips facing the rear.
• If there are skis with different lengths in the removeable through-loading bag,
ensure that the bindings are always positioned at the same height.
• The removeable through-loading bag must never be folded together or stowed
when moist.
ABA
A
sgg.6.book Page 94 Thursday, September 24, 2009 2:32 PM
Heating and air conditioning system 95
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Heating and air conditioning system
Air outlet vents
The information provided is valid for all vehicles.
Fig. 106 Air vents at the front
Fig. 107 Air vents at the rear
Open the air outlet vents 3 and 4
– Turn the horizontal wheel (to the right) ⇒ fig. 106.
Open the air outlet vents 6
– Turn the vertical wheel (between the end positions) ⇒ fig. 107.
Close air outlet vents 3 and 4
– Turn the horizontal wheel into the end position (to the left).
Close air outlet vents 6
– Turn the vertical wheel into the end position.
Change air flow of air outlet vents 3 and 4
– In order to change the strength of the air flow, swivel the horizontal lamellas with
the aid of the moveable adjuster.
– In order to change the lateral direction of the air flow, turn the vertical lamellas with
the aid of the moveable adjuster.
Change air flow of air outlet vents 6
– In order to change the strength of the air flow, swivel the horizontal lamellas with
the aid of the vertical wheel upwards or downwards.
– In order to change the lateral direction of the air flow, turn the vertical lamellas with
the aid of the horizontal wheel to the left or to the right.
The air outlet vents 3, 4 ⇒ fig. 106 and 6 ⇒ fig. 107 can be closed and opened individ-
ually.
The air outlet vents 6 are only fitted on vehicles with higher centre console.
Warmed, unwarmed or cooled air will flow out of the air outlet vents according to the
setting of the regulator of the heating or the air conditioning system* and the atmospheric conditions.
sgg.6.book Page 95 Thursday, September 24, 2009 2:32 PM
Heating and air conditioning system96
Heating
Using the system
The heating system delivers air into the interior of the vehicle and
warms it as required.
Fig. 108 Heating: Control elements
Setting temperature
– Turn the control dial ⇒ fig. 108 to the right in order to increase the temperature.
– Turn the control dial to the left in order to increase the temperature.
Controlling blower
– Turn the blower switch into one of the positions, 1 to 4, in order to switch the
blower on.
– Turn the blower switch into position 0 in order to switch the blower off.
– If you wish to shut off the fresh air supply, us e the bu tton - recircul ated ai r mode
⇒ .
Control for air distribution
– You can adjust the direction of the air flow using the air distribution control
⇒ page 95.
Rear window heater
– Press button . Further information ⇒ page 62, “Rear window heater”.
Auxiliary heating (auxiliary heating)*
– Press the button in order to directly switch on/off the auxiliary heating (auxiliar y
heating and ventilation). Further i nformation ⇒ page 105, “Auxiliary heating (auxiliary heating and ventilation)*”.
The air inlet in front of the windscreen must be free of ice, snow or leaves in order to
ensure that the heating and ventilation systems operate properly.
The heating effect is dependent upon the coolant temperature, thus full heat output
only occurs when the engine has reached its operating temperature.
The blower should aways be on to prevent the windows from misting up.
WARNING
You should not leave recirculated air mode on over a longer period of time, as
“stale” air may result in fatigue in the driver and occupants, divert your attention and also cause the windows to mist up. The risk of having an accident
increases. Switch recirculated air mode off as soon as the windows begin
misting up.
Note
• The whole heat output will be needed to unfrost the windscreen and side windows.
No warm air will be fed to the footwell. This can lead to restriction of the heating
comfort.
• The used air streams out through the air removal openings in the luggage
compartment.
A
A
A
A
ABA
B
A1ACA2A
3
sgg.6.book Page 96 Thursday, September 24, 2009 2:32 PM
Heating and air conditioning system 97
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Set heating
Recommended settings of heating controls for:
Note
We recommend that you leave the air outlet vents 3 ⇒ page 95, f ig. 106 in the opened
position.
Set-up
Setting of the control dial
Button
Air outlet vents 4
Defrosting the windscreen and side
windows
To the right up to the
stop
3
Do not switch on
Open and align with the side win-
dow
Free windscreen and side windows
from mist
Desired temperature 2 or 3
Do not switch on
Open and align with the side win-
dow
The fastest heating
To the right up to the
stop
3
briefly switched on Opening
Comfortable heating Desired temperature 2 or 3
Do not switch on Opening
Fresh air mode - ventilation
To the left up to the
stop
Desired position
Do not switch on Opening
A
1
AAABA
C
sgg.6.book Page 97 Thursday, September 24, 2009 2:32 PM
Heating and air conditioning system98
Recirculated air mode
In recirculated air mode air is sucked out of the interior of the vehicle
and then fed back into the interior.
Recirculated air mode prevents polluted air outside the vehicle from getting into the
vehicle, for example when driving through a tunnel or when standing in a traffic jam.
Switching recirculated air mode on
– Press the button - the warning light lights up in the button ⇒ page 96, fig. 108.
Switching recirculated air mode off
– Press again the button - the warning light in the button goes out.
The recirculated air mode is switched off automatically if the air distribution control
is in position ⇒ page 96, fig. 108. You can also switch recirculated air mode on
again from this setting by repeatedly pressing button .
WARNING
You should not leave recirculated air mode on over a longer period of time, as
“stale” air may result in fatigue in the driver and occupants, divert your attention and also cause the windows to mist up. The risk of having an accident
increases. Switch recirculated air mode off as soon as the windows begin
misting up.
Climatic* (semi-automatic air conditioning system)
Description
The Climatic is a combined cooling and heating system. It makes it
possible to optimally control the air temperature at any season of the
year.
Description of the Climatic
It is important for your safety and for your driving comfort that the Climatic is operating
properly.
The cooling only operates if button ⇒ page 99, fig. 109 is pressed, and the
following conditions are met:
• engine running,
• outside temperature above approx. +2°C and
• blower switch switched on (positions 1 to 4).
If the cooling system is switched on, the temperature and air humidity drops in the
vehicle. The wellbeing of the occupants of the car is enhanced as a result of this particularly at high outside temperatures and a high air humidity. The system prevents the
windows misting up during the cold season of the year.
The heating effect is dependent upon the coolant temperature, thus full heat output
only occurs when the engine has reached its operating temperature.
It is possible to briefly activate recirculated air mode in order to enhance the cooling
effect ⇒ .
Air at a temperature of about 5°C may flow out of the vents under certain circumstances when the cooling system is operating. Lengthy and uneven distribution of the
air flow out of the vents and large differences in temperature, for example when getting
out of the vehicle, can result in chills in sensitive persons.
The air inlet in front of the windscreen must be free of ice, snow or leaves in order to
ensure that the heating and cooling systems operate properly.
After switching on the cooling Condensation from the evaporator of the air conditioning may drip down and form a puddle below the vehicle. This is quite normal and
not an indication of a leak!
WARNING
• For your own safety and that of other road users, ensure that all the
windows are free of ice, snow and misting. Please familiarize yourself about
how to correctly operate the heating and ventilation systems, how to demist
and defrost the windows, as well as with the cooling mode.
• You should not leave recirculated air mode on over a longer period of time,
as “stale” air may result in fatigue in the driver and occupants, divert your
attention and also cause the windows to mist up. The risk of having an accident
increases. Switch recirculated air mode off as soon as the windows begin
misting up.
A
C
AC
A
1
sgg.6.book Page 98 Thursday, September 24, 2009 2:32 PM
Heating and air conditioning system 99
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• We recommend that you do not smoke in the vehicle when the recirculating air
mode is operating since the smoke which is drawn at the evaporator from the interior
of the vehicle forms deposits in the evaporator of the air conditioning system. This
produces a permanent odour when the air conditioning system is operating which can
only be eliminated through considerable effort and expense (replacement of
compressor).
Using the system
Fig. 109 Climatic: Control elements
Setting temperature
– Turn the control dial ⇒ fig. 109 to the right in order to increase the temperature.
– Turn the control dial to the left in order to increase the temperature.
Controlling blower
– Turn the blower switch into one of the positions, 1 to 4, in order to switch the
blower on.
– Turn the blower switch into position 0 in order to switch the blower off.
– If you wish to shut off the fresh air supply, use the button - recirculated air
mode ⇒ page 101.
Control for air distribution
– You can adjust the direction of the air flow using the air distribution control
⇒ page 95.
Switching cooling on and off
– Press the button ⇒ fig. 109. The warning light lights up in the button.
– When you again press the switch , the cooling system is switched off. The
warning light in the button goes out.
Rear window heater
– Press button . Further information ⇒ page 62, “Rear window heater”.
Auxiliary heating (auxiliary heating)
– Press the button in order to directly switch on/off the auxiliary heating
(auxiliary heating and ventilation). Further information ⇒ page 105, “Auxiliary
heating (auxiliary heating and ventilation)*”.
The set temperature will be automatically maintained other than when the
control dial is on the extreme right or extreme left position:
• Extreme right position - full heating;
• Extreme left position - full cooling;
• The blower should aways be on to prevent the windows from misting up.
Note
• T he who le hea t o utp ut wi ll b e n eed ed to u nf ros t t he w in dsc ree n a nd sid e w ind ow s.
No warm air will be fed to the footwell. This can lead to restriction of the heating
comfort.
• The used air streams out through the air removal openings in the luggage compart-
ment.
• If the cooling system has not been switched on for a lengthy period, odours may
be produced at the evaporator because of deposits. Switch the cooling system on at
least once a month for approximately 5 minutes at the highest blower stage - also
during the cold season of the year - in order to remove such odours. Also open a
window for a short time.
AAAAABA
B
A4A
C
AC
A
1
AC
A
2
A
3
sgg.6.book Page 99 Thursday, September 24, 2009 2:32 PM
Loading...