Skoda Roomster 2014 User Manual

Download

Page 1

SIMPLY CLEVER

ŠKODA Roomster Owner's Manual

Page 2

Layout of this Owner's Manual (explanations)

This Owner's Manual has been systematically designed to make it easy for you to search for and obtain the information you require.

Chapters, table of contents and subject index

The text of the Owner's manual is divided into relatively short sections which are combined into easy-to-read chapters. The chapter you are reading at any particular moment is always specified on the bottom right of the page.

The Table of contents is arranged according to the chapters and the detailed Subject index at the end of the Owner's Manual helps you to rapidly find the information you are looking for.

Direction indications

All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of travel of the vehicle.

Units of measurement

All values are expressed in metric units.

Explanation of symbols

 Denotes a reference to a section with important information and safety

advice in a chapter.

 Denotes the end of a section.

 Denotes the continuation of a section on the next page.

 Indicates situations where the vehicle must be stopped as soon as

possible.

® Denotes a registered trademark.

 Denotes the display in the MAXI DOT display.  Denotes the display in the segment display.

Display

The display in the segment display will be used in this Owner's Manual to represent the display unless otherwise specified.

Notes

WARNING

The most important notes are marked with the heading WARNING. These WARNING notes draw your attention to a serious risk of accident or injury.

CAUTION

A Caution note draws your attention to the possibility of damage to your vehicle (e.g. damage to gearbox), or points out general risks of an accident.

For the sake of the environment

An Environmental note draws your attention to environmental protection aspects. This is where you will, for example, find tips aimed at reducing your fuel consumption.

Note

A normal Note draws your attention to important information about the operation of your vehicle.



5J7012720AG

Page 3

Preface

You have opted for a ŠKODA – our sincere thanks for your confidence in us.

You have received a vehicle with the latest technology and range of amenities. Please read this Owner's Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use of the vehicle.

If you have any questions about your vehicle, please contact a ŠKODA Partner. We hope you enjoy driving your ŠKODA, and wish you a pleasant journey at all times. Your ŠKODA AUTO a.s. (hereinafter referred to only as ŠKODA or manufacturer)



Page 4

Terms used

The on-board literature contains the following terms relating to the service work for your vehicle.

“Specialist garage” - a workshop that carries out specialist service tasks for

›

ŠKODA vehicles A specialist garage can be a ŠKODA partner, a ŠKODA service partner or an independent workshop. “ŠKODA service partner” - A Workshop that has been contractually author-

›

ized by the manufacturer ŠKODA AUTO a.s. or its sales partner to perform service tasks on ŠKODA vehicles and to sell ŠKODA Genuine Parts. “ŠKODA partner” - A company that has been authorized by the manufacturer

›

ŠKODA AUTO a.s. or its sales partner to sell new ŠKODA vehicles and, when applicable, to service them using ŠKODA Genuine Parts and sell ŠKODA Genuine Parts.

Owner's Manual

These operating instructions apply to all body variants of the vehicle and all related models.

The manual describes all possible equipment variants without identifying them as special equipment, model variants or market-dependent equipment.

Consequently, this vehicle does not necessarily contain all of the equipment components described in this Owner's Manual.

The scope of equipment on your vehicle depends on your purchase contract for the vehicle. More information is available from the ŠKODA Partner from whom you bought the vehicle.

The illustrations can differ in minor details from your vehicle; they are only intended for general information.

Supplementary Information (applies to Russia)

The full type approval number of the means of transport is indicated in the registration documents.

Page 5

Abbreviations

Safety

Passive Safety 6

General information 6 Correct and safe seated position 7

Seat belts 10

Using seat belts 10 Inertia reels and belt tensioners 13

Airbag system

Description of the airbag system 14 Airbag overview 15 Deactivating airbags 18

Transporting children safely 20

Child seat 20 Fastening systems 22

Operation

Cockpit

Overview

Instruments and Indicator Lights

Instrument cluster Multifunction display (MFD) Service Interval Display MAXI DOT display Warning lights

Unlocking and locking

Unlocking and locking Central locking system Remote control Anti-theft alarm system

28 28

34 35 37

44 44 47 50

Luggage compartment lid 52 Electrical power windows 53

Lights and visibility 56

Lights 56 Interior lights 60 Visibility 61 Windscreen wipers and washers 62 Rear window 64

Seats and stowing 66

Front seats 66 Rear seats 67 Head restraints 69

Boot 70 Variable loading floor in the luggage

compartment (Estate) 73 Bicycle carrier in the luggage compartment 75 Roof rack system 77 Useful equipment 77 Storage compartments 80 Praktik 84

Heating and air-conditioning 87

Heating, ventilation, cooling 87

Heating 88 Air conditioning system (manual air

conditioning system) 90 Climatronic (automatic air conditioning

system) 92

Communication and multimedia 94

Universal telephone preinstallation GSM II 94 Voice control 99 Multimedia 100

Driving

Starting-off and Driving 103

Starting and stopping the engine 103 Brakes 105

Manual gear changing and pedals 106 Automatic transmission 107 Running in 110 Economical driving and environmental

sustainability 110 Avoiding damage to your vehicle 114 Driving abroad 115

Assist systems 116

Brake assist systems 116 Parking aid 117 Cruise Control System 118 START-STOP 120

Towing a trailer 122

Towing device 122 Trailer 126

General Maintenance

Car care 128

Services, modifications and technical alterations 128

Washing your car 130 Taking care of your vehicle exterior 131 Taking care of the interior 134

Inspecting and replenishing 137

Fuel Engine compartment 140 Engine oil 143 Coolant 145 Brake fluid 147 Vehicle battery 147

Wheels 151

Tyres and wheel rims 151 Winter operation 156

137

Table of Contents

Page 6

Do-it-yourself

Emergency equipment and self-help 158

Emergency equipment 158 Changing a wheel 159 Tyre repair 162 Jump-starting 164 Towing the vehicle 166

Fuses and light bulbs 168

Fuses 168 Bulbs 170

Technical data

Vehicle data 175

175

Index

Table of Contents

Page 7

Abbreviations

Abbreviation Definition

rpm Engine revolutions per minute ABS Anti-lock brake system

AG Automatic gearbox

TCS Traction control

CO2 in g/km

DPF Diesel particle filter DSG Automatic double clutch gearbox

ECE Economic Commission for Europe ESC Electronic Stability Control

EU European Union kW Kilowatt, measuring unit for the engine output MG Manual gearbox

MFD Multifunction display

Nm Newton meter, measuring unit for the engine torque

TDI CR

TSI Petrol engine with turbocharging and direct injection

discharged quantity of carbon dioxide in grams per driven kilometer

Panel van intended exclusively or mainly for the transportation of goods

Diesel engine with turbocharging and common rail injection system

Abbreviations

Page 8

Safety

Passive Safety

General information

 Introduction

This chapter contains information on the following subjects: Before setting off

Driving safety 6 Safety equipment 6

In this section you will find important information, tips and notes on the subject of passive safety in your vehicle.

We have combined everything here which you should be familiar with, for example, regarding seat belts, airbags, child seats and safety of children.

WARNING

■

This chapter contains important information on how to use the vehicle for

the driver and his occupants.

■

You can find further information on safety concerning you and those trav-

elling with you in the following chapters of this owner's manual.

■

The complete on-board literature should always be in the vehicle. This

applies in particular, if you rent out or sell the vehicle.

Before setting off

Read and observe on page 6 first.



For your own safety and the safety of the people travelling with you, please pay attention to the following points before setting off.

Ensure that the lighting and the turn signal system are functioning proper-



ly. Ensure that the function of the wiper and the condition of the wiper



blades are free of any defects. Ensure that all of the windows offer good visibility to the outside.



Adjust the rear-view mirror so that vision to the rear is guaranteed.



Ensure that the mirrors are not covered.



Check the tyre inflation pressure.



Check the engine oil, brake fluid and coolant level.



Secure all items of luggage.



Do not exceed the permissible axle loads and permissible gross weight of



the vehicle. Close all doors as well as the bonnet and boot lid.



Ensure that no objects can obstruct the pedals.



Protect children in suitable child seats with correctly fastened seat



belts » page 20, Transporting children safely. Adopt the correct seated position » page 7, Correct and safe seated



position. Tell your passengers to assume the correct seated position.

Driving safety

Read and observe on page 6 first.



The driver is fully responsible for himself and his occupants. If your driving safety is effected, you place yourself and the oncoming traffic at risk.

The following guidelines must therefore be observed.

Do not become distracted from concentrating on the traffic situation, e.g.



by your passengers or mobile phone calls. Never drive when your driving ability is impaired, e.g. due to medication, al-



cohol or drugs. Keep to the traffic regulations and the permissible speed limit.



Always adjust the driving speed to the road, traffic and weather condi-



tions. Take regular breaks on long journeys – at least every two hours.



Safety equipment

Read and observe



The following list contains only part of the safety equipment in your vehicle.

Three-point seat belts for all the seats.

›

Belt force limiters for the front seats.

›

Belt tensioners for the front seats.

›

Seat belt height adjusters for the front seats.

›

Front airbag for the driver and the front passenger.

›

Side airbags.

›

on page 6 first.



Safety

Page 9

Head airbags.

›

Anchoring points for child seats using the ISOFIX system.

›

Anchoring points for child seats using the TOP TETHER system.

›

Head restraints adjustable for height.

›

Adjustable steering column.

›

The specified safety equipment works together, in order to optimally protect you and those travelling with you in accident situations.

The safety equipment does not protect you or the people travelling with you, if you or your occupants adopt an incorrect seated position or the equipment is not correctly adjusted or used.

If the seat belt is not fastened properly, this may result in injuries if an airbag is activated in the event of an accident.

Correct and safe seated position



Introduction

This chapter contains information on the following subjects: Correct seated position for the driver

Adjusting the steering wheel position 8 Correct seated position for the front passenger 8 Correct seated position for the passengers in the rear seats 9 Examples of incorrect seated positions 9

WARNING

■

The front seats and all head restraints must be adjusted to match the body size at all times and the seat belt must always be fastened properly to provide the most effective levels of protection to the passengers.

■

Each occupant must correctly fasten the seat belt belonging to the seat. Children must be fastened » page 20, Transporting children safely with a suitable restraint system.

■

If the occupant adopts an incorrect seated position, he is exposed to lifethreatening injuries, in case he is hit by a deployed airbag.

■

If the occupants on the rear seats are not sitting upright, the risk of injury is increased due to incorrect routing of the seat belt.

■

The seat backrests must not be tilted too far back when driving, as this will impair the function of the seat belts and of the airbag system – risk of injury!

Correct seated position for the driver

Fig. 1 The correct distance of the driver to the steering wheel/correctly adjusted head restraint

Read and observe



For your own safety and to reduce the risk of injury in the event of an accident, the following instructions must be observed.



Adjust the driver’s seat in the forward/back direction so that the pedals can be fully depressed with slightly bent legs.



Adjust the seat backrest so that the highest point of the steering wheel can be reached with your arms at a slight angle.



Adjust the steering wheel so that the distance A between the steering wheel and your chest is at least 25 cm » Fig. 1. Adjust the steering wheel » page 8, Adjusting the steering wheel position.



Adjust the head restraint such that the top edge of the head restraint is at the same level as the upper part of your head B .

Correctly fasten the seat belt » page 10, Using seat belts.



Adjust the seats and head restraints » page 66.

on page 7 first.



Passive Safety

Page 10

WARNING

■

Always assume the correct seated position before setting off and do not change this position while driving. Also advise your passengers to adopt the correct seated position and not to change this position while the car is moving.

■

Maintain a distance of at least 25 cm from the steering wheel, and a distance of at least 10 cm between the legs and the dash panel at the height of the knee airbag. Not keeping to this minimum distance will mean that the airbag system will not be able to properly protect you – risk of death!

■

When driving, hold the steering wheel with both hands firmly on the outer edge in the “9 o'clock” and “3 o'clock” position. Never hold the steering wheel in the “12 o'clock” position or in any other way (e.g. in the middle or inner edge of the steering wheel). In such cases, you could severely injure your arms, hands and head when the driver airbag is deployed.

■

Ensure that there are no objects in the driver's footwell, as these may get caught in the pedal apparatus when driving or braking. You would then no longer be able to operate the clutch, brake or acceleration pedals.

Adjusting the steering wheel position

Fig. 2

Adjustable steering wheel: Lever underneath the steering wheel

Read and observe on page 7 first.



The height and forward/back position of the steering wheel can be adjusted.

Swivel the lever underneath the steering wheel downwards » Fig. 2.

›

Adjust the steering wheel to the desired position (with regard to the height

›

and forward/back position). Push the lever upwards to the stop.

›

WARNING

■

The lever for adjusting the steering wheel must be locked whilst driving so that the position of the steering wheel cannot accidentally change during the journey – risk of accident!

■

Never adjust the steering wheel when the vehicle is moving only when the vehicle is stationary!

Correct seated position for the front passenger

Read and observe



For passenger safety and to reduce the risk of injury in an accident, the following instructions must be observed.

Position the front passenger seat back as far as possible. The front pas-



senger must maintain a distance of at least 25 cm to the dash panel so that the airbag offers the greatest possible safety if it is deployed.



Adjust the head restraint such that the top edge of the head restraint is at the same level as the upper part of your head B » Fig. 1 on page 7 » page 7.



Correctly fasten the seat belt » page 10. Adjust the seats and head restraints » page 66. In exceptional cases the front passenger airbag can be deactiva-

ted » page 18, Deactivating airbags.

WARNING

■

Maintain a distance of at least 25 cm to the dash panel. Not keeping to this minimum distance will mean that the airbag system will not be able to properly protect you – risk of death!

■

Always keep your feet in the footwell when the car is being driven – never place your feet on the instrument panel, out of the window or on the surfaces of the seats. You will be exposed to increased risk of injury if it becomes necessary to apply the brake or in the event of an accident. If an airbag is deployed, you could suffer fatal injuries by adopting an incorrect seated position!

on page 7 first.

Safety

Page 11

Correct seated position for the passengers in the rear seats

Read and observe on page 7 first.



To reduce the risk of injury in the event of a sudden braking manoeuvre or an accident, the occupants on the rear seats must observe the following.

Adjust the head restraint such that the top edge of the head restraint is at



the same level as the upper part of the head B » Fig. 1 on page 7 » page 7.



Correctly fasten the seat belt » page 10, Using seat belts.



Use a suitable child restraint system if transporting children in the vehicle » page 20, Transporting children safely.

Adjust the seats and head restraints » page 66.

Examples of incorrect seated positions

Read and observe



Maximum seat belt protection is only achieved if seat belts are fastened correctly.

Incorrect seated positions considerably reduce the protective functions of the seat belts and therefore increase the risk of injury due to an incorrect routing of the seat belt.

The driver is fully responsible for himself and passengers, especially children. Never allow a passenger to adopt an incorrect seated position when the car is moving.

The following list contains instructions which, if not observed, may cause serious injuries or death. This list is not complete, however we would like you to familiarise yourself with this subject.

Observe the following instructions while driving.

Do not stand up.



Do not stand on the seats.



Do not kneel on the seats.



Do not tilt the seat backrest too far back.



Do not lean against the dash panel.



Do not lie on the rear seats.



Do not sit only on the front part of the seat.



Do not sit facing to the side.



on page 7 first.

Do not lean out of the window.



Do not put your feet out of the window.



Do not put your feet on the dash panel.



Do not put your feet on the seat cushion.



Do not allow anybody to travel in the footwell.



Do not drive without fastening your seat belt.



Do not delay in the luggage compartment.



Passive Safety

Page 12

Seat belts

Using seat belts

Introduction



Fig. 3

Driver wearing seat belt

This chapter contains information on the following subjects: The physical principle of a frontal collision 11

Fastening and unfastening seat belts 12 Belt height adjustment on the front seats 13 Seat belt for the rear middle seat 13

Seat belts that are fastened correctly offer good protection in the event of an accident. They reduce the risk of an injury and increase the chance of survival in the event of a major accident.

Correctly fastened seat belts hold occupants of the car in the correct seated position » Fig. 3.

The seat belts reduce the kinetic energy (energy of motion) to a considerable extent. They also prevent uncontrolled movements which, in turn, may well result in severe injuries.

Occupants of a vehicle who have correctly fastened their seat belts have the major benefit of the fact that the kinetic energy is absorbed as effectively as possible by the belts.

The structure of the front end of the vehicle and other passive safety measures, such as the airbag system, also contribute to the kinetic energy being reduced as effectively as possible. The energy produced is thus absorbed and there is less risk of injury.

Particular safety aspects must be observed when transporting children in the vehicle » page 20, Transporting children safely.

WARNING

■

Fasten your seat belt before each journey - even when driving in town! This also applies to the passengers seated at the rear – risk of injury!

■

Expectant women must also always wear a seat belt. This is the only way of ensuring optimal protection for the unborn child » page 12, Fastening and unfastening seat belts.

■

Maximum seat belt protection is only achieved if you are correctly seated » page 7, Correct and safe seated position.

■

The seat backrests of the front seats must not be tilted too far to the rear otherwise the seatbelts can lose their effectiveness.

WARNING

Information on the correct routing of the belt

■

Always ensure that the webbing of the seat belts is properly routed. Seat belts which are not correctly adjusted can themselves cause injuries even in minor accidents.

■

Adjust the height of the belt in such a way that the shoulder part of the belt is roughly positioned across the middle of your shoulder - on no account across your neck.

■

A seat belt which is hanging too loose can result in injuries as your body is moved forward by the kinetic energy produced in an accident and is then suddenly held firm by the belt.

■

The belt webbing must not run across solid or fragile objects (e.g. spectacles, ball-point pens, bunches of keys etc.). Such objects can cause injury.

WARNING

Information on dealing with the safety belts

■

The belt webbing must not be jammed in-between at any point or twisted, or chafe against any sharp edges.

■

Make sure you do not catch the seat belt when closing the door.

WARNING

Information on the proper use of the safety belts

■

Never use one seat belt to secure two persons (including children). The seatbelt must not be placed over a child who is sitting on the lap of another passenger.



Safety

Page 13

WARNING (Continued)

■

The lock tongue should only be inserted into the lock which is the correct one for your seat. Wrong use of the safety belt will reduce its capacity to protect and the risk of injury increases.

■

The slot of the belt tongue must not be blocked, otherwise the belt tongue will not lock in place properly.

■

Many layers of clothing and loose clothing (e. g. a winter coat over a jacket) do not allow you to be correctly seated and impairs proper operation of the seat belts.

■

It is prohibited to use clamps or other objects to adjust seat belts (e. g. for shortening the belts for smaller persons).

■

The seat belts for the rear seats can only fulfil their function reliably when the seat backrests are correctly locked into position » page 68.

WARNING

Information on the care and maintenance of the safety belts

■

The belt webbing must always be kept clean. Soiled belts may impair proper operation of the inertia reel » page 136, Seat belts.

■

The seat belts must not be removed or changed in any way. Do not attempt to repair the seat belts yourself.

■

Check the condition of all the seat belts on a regular basis. If any damage to the seat belts, seat belt connections, inertia reel or the lock is detected, the relevant seat belt must be replaced by a specialist garage.

■

Damaged seat belts which have been subjected to stress in an accident and were therefore stretched, must be replaced - this is best done by a specialist garage. The anchorage points of the belts must also be inspected. The anchorage points for the belts should also be checked.

Note

The national legal requirements must be observed when using seat belts.

The physical principle of a frontal collision

Fig. 4 Driver without a fastened seat belt/rear seat passenger without a fastened seat belt

Read and observe



As soon as the vehicle is moving, so-called kinetic energy (the energy of motion) is produced both in terms of the car as well as in terms of the occupants.

The magnitude of this kinetic energy depends essentially on the speed at which the vehicle is travelling and on the weight of the vehicle including the occupants. The greater the speed and weight increase, the greater the amount of energy which has to be absorbed in the event of an accident.

The speed of the vehicle is the most important factor. Doubling the speed of the vehicle from 25 km/h up to 50 km/hour increases the kinetic energy four times.

The idea that it is possible to support your body with your hands in a minor accident is incorrect. Even in a collision at only a low speed, the forces acting on the body are such that it is no longer possible to support your body.

Even if you only drive at a speed of 30-50 km/h, the forces that your body is exposed to in the event of an accident can exceed a metric ton (1000 kg).

For example, a person's weight of 80 kg “increases” to 4.8 tons (4800 kg) at 50 km/h.

In the event of a frontal collision, occupants of the car not wearing a seat belt are thrown forward and strike parts of the interior of the car, such as the steering wheel, dash panel, windscreen in ways which cannot be controlled » Fig. 4 - . In certain circumstances you could even be thrown out of the vehicle, which could cause life threatening or even fatal injuries.

on page 10 first.



Seat belts

Page 14

It is also important that rear passengers fasten their seat belts, as they could otherwise be thrown through the vehicle in an uncontrolled manner in the event of an accident.

A rear seat passenger who has not fastened the seat belt is a danger not only to himself but also for those seated in the front » Fig. 4 - .

Fastening and unfastening seat belts

Fig. 5 Fastening/unfastening the seat belt

Fig. 6 Routing of belt webbing over the shoulders and the lap belt/Rout-

ing of belt webbing for an expectant mother

Insert the lock tongue into the belt buckle belonging to the seat » Fig. 5 – 

›

until it you hear it click into place. Pull on the belt to check that it has engaged correctly in the lock.

›

A plastic knob in the belt webbing holds the belt tongue in a position which is easy to get hold of.

It is important that the belt is properly routed to ensure seat belts offer the maximum protection.

The shoulder part of the seat belt must never run across the neck but must roughly run over the middle of the shoulder and fit snugly against the chest. The lap part of the belt must run across the pelvis, must not be lie across the stomach and must always fit snugly » Fig. 6 - .

Expectant women must also always wear a seat belt. This is the only way of ensuring optimal protection for the unborn child.

The lap part of the belt must be positioned as low as possible on the pelvis on expectant mothers to avoid exerting any pressure on the lower abdomen » Fig. 6 - .

Release

Release the seat belt only when the vehicle is stationary.

Press the red button in the belt buckle » Fig. 5 - , the lock tongue pops out.

›

Manually guide the belt back so that it is easier to fully roll up the webbing,

›

the seat belt does not twist.

CAUTION

When releasing the seatbelt ensure that the tongue of the lock does not damage the door trim or other parts of the interior.

Read and observe on page 10 first.



Fastening

Correctly adjust the front seat and head restraint before fastening the seat

›

belt » page 69. Use the lock tongue to slowly pull the webbing over your chest and pelvis.

›

Safety

Page 15

Belt height adjustment on the front seats

Fig. 7

Front seat: Seat belt height adjuster

Release

Take off the safety belt in the reverse order to how you fasten it.

›

Guide the belt back by hand so that the webbing rolls up easily, the seat belt

›

is not twisted and the trim panel is not damaged.

WARNING

■

After releasing the seat belt, hold it tight and let it slowly reel up until both locking tongues lock into the headliner mounting and are secured with a magnet - risk of injury.

■

Never unlock both lock tongues simultaneously.

Read and observe on page 10 first.



The seat belt height adjuster makes it possible to adjust the routing of the front seat belts in the area of the shoulder to the body size.

Press the height adjuster and move up or down in the desired direc-

›

tion » Fig. 7. Then pull firmly on the belt to ensure that the seat belt height adjuster has

›

correctly locked in place.

Seat belt for the rear middle seat

Read and observe



The seat belt for the rear middle seat is anchored in the area of the boot on the left side of the headliner.

Fastening

Pull the belt with both lock tongues out of the headliner mount.

›

Insert the lock tongue at the end of the belt into the belt buckle on the left

›

side until it is heard to lock in place. Pull the second lock tongue, which is moveable on the seat belt, over the

›

chest and insert it into the belt buckle on the right side until it is heard to lock in place. Pull on the seat belt to check that both lock tongues are securely engaged in

›

the locks.

The belt tongues for the rear middle seat are shaped differently so that they only fit into the correct belt buckle. If you are not able to insert a lock tongue into the wrong belt lock you probably tried to put it into the wrong buckle.

on page 10 first.

Inertia reels and belt tensioners

Introduction



This chapter contains information on the following subjects: Inertia reels

Belt tensioners 13

Inertia reels

Each seat belt is equipped with an inertia reel. When pulling slowly on the seat belt, the belt can move freely. When pulling

sharply on the seat belt, the movement is locked by the inertia reel. The belts also lock when full braking, when the car accelerates, when driving

downhill and when cornering.

WARNING

If the seat belt does not lock when pulling sharply on it, have it inspected immediately by a specialist garage.

Belt tensioners

Safety for the driver and front passenger wearing their seat belts is enhanced by the belt tensioners fitted to the inertia reels of the front three-point seat belts.

The three-point seat belts are automatically tensioned in the event of a frontal collision of a certain severity. The belt tensioners can also be deployed if the seat belts are not fastened.

Seat belts



Page 16

The fastened three-point seat belts are automatically tensioned in the event of a lateral collision of a certain severity.

Belt tensioners are not activated in the event of minor frontal collisions, side and rear-end collisions, in the case of a rollover and also not in accidents in which no major forces are produced from the front.

WARNING

■

Any work on the belt tensioner system including removal and installation of system components because of other repair work, must only be carried out by a specialist garage.

■

The protective function of the system is only adequate for a single accident. If the belt tensioners have been deployed, it is then necessary to replace the entire system.

Note

■

Smoke is generated when the belt tensioners are deployed. This is not an in-

dication of a fire in the vehicle.

■

When disposing of the vehicle or parts of the belt tensioner system, it is im-

portant to comply with national legal requirements. ŠKODA service partners are familiar with these regulations and will be able to provide you with detailed information.

Airbag system

Description of the airbag system

Introduction



This chapter contains information on the following subjects: System description 15

Airbag deployment 15

WARNING

■

An airbag can only offer you optimal protection in combination with a

fastened seat belt.

■

The airbag is not a substitute for the seat belt, but instead forms part of

the complete passive vehicle safety concept.

■

To ensure passengers are protected with the greatest possible effect when the airbag is deployed, the front seats must be correctly adjusted to match the body size » page 7, Correct and safe seated position.

■

If you do not fasten the seat belts when driving, lean too far forward or adopt an incorrect seated position, you are exposing yourself to increased risk of injury in the event of an accident.

WARNING

Information on the use of the airbag system

■

If there is a fault, the airbag system must be checked by a specialist garage immediately. Otherwise, there is a risk of the airbag not being activated in the event of an accident.

■

No modifications of any kind must be made to parts of the airbag system.

■

Any work on the airbag system including the installation and removal of system components due to other repair work (e.g. removal of the steering wheel) must only be carried out by a specialist garage.

■

Never make any changes to the front bumper or bodywork.

■

It is prohibited to manipulate individual parts of the airbag system as this might result in the airbag being deployed.

■

The protective function of the airbag system is sufficient for only one accident. The airbag system must then be replaced if the airbag has been deployed.

Safety

Page 17

System description

Read and observe on page 14 first.



The functional status of the airbag system is indicated by the indicator light in the instrument cluster » page 42.

When the airbags are deployed, they fill with gas and inflate. A grey white or red, non-harmful gas is released when the airbag is inflated.

This is perfectly normal and is not an indication of a fire in the vehicle.

Depending on the vehicle equipment, the airbag system consists of the following modules.

Electronic control unit.

›

Front airbag for the driver and the front passenger » page 16.

›

Side airbags » page 17.

›

Head airbags » page 17.

›

Airbag warning light in the instrument cluster » page 42.

›

Key switch for the front passenger airbag » page 19.

›

Warning light for the front passenger airbag deactivation/activation in the

›

middle of the dash panel » page 19.

Note

■

The airbag system needs no maintenance during its working life.

■

If you sell your vehicle, provide the complete vehicle documentation to the new owner. Please note that the information relating to the possibility of deactivating the front passenger airbag must be included!

■

When disposing of vehicle or parts of the airbag system, it is important to comply with the national legal requirements.

Airbag deployment

Read and observe



The airbags inflate in fractions of a second and at a high speed in order to be able to offer additional protection in the event of an accident.

The airbag system is only functional when the ignition is switched on. In certain accident situations, the several airbags may be deployed simultane-

ously. The airbags are not deployed in the case of minor frontal and side collisions,

rear-end collisions, tilting of the vehicle and vehicle rollover.

on page 14 first.

Deployment factors

It is not possible to generally determine which deployment conditions apply to the airbag system in every situation. An important role is played by factors such as the type of object that the vehicle hits (hard/soft), the impact angle,



vehicle speed etc. A decisive factor for the deployment of the airbags is the deceleration which

occurs. The control unit analyses the nature of the collision and activates the relevant restraint system.

If the vehicle deceleration which occurs and is measured during the collision remains below the prescribed reference values specified in the control unit, the airbags are not deployed although the vehicle may well suffer severe damage to the bodywork as a consequence of the accident.

The following airbags will be deployed in the event of a severe frontal collision.

Driver’s front airbag.

›

Front passenger airbag.

›

The following airbags will be deployed in the event of a severe side collision.

Front side airbag on the side of the accident.

›

Head airbags on the side of the accident.

›

In the event of an accident in which the airbags are deployed:

the interior lighting comes on (if the switch for the interior light is in the door

›

contact position), the hazard warning light is switched on;

›

all the doors are unlocked;

›

the fuel supply to the engine is interrupted.

›

Airbag overview



Introduction

This chapter contains information on the following subjects: Front airbags

Side airbags 17 Head airbags 17

Airbag system

Page 18

Front airbags

Fig. 8 Driver airbag in the steering wheel/front passenger airbag in the dashboard

WARNING

Information on correct seated position

■

For the driver and front passenger, it is important to maintain a distance of at least 25 cm from the steering wheel or dashboard A » Fig. 9. Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you - hazard! The front seats and the head restraints must always also be correctly adjusted to match the body size of the occupant.

■

The airbag develops enormous forces when triggered, which can lead to injuries if the sitting position or seated position is not correct.

■

There must not by any further persons, animals or objects positioned between the front seated occupants and the deployment area of the airbag.

WARNING

Front airbag and transporting children

■

Never transport children on the front seat of a vehicle without using a proper restraint system. If airbags are deployed in the event of an accident, the child might suffer severe or even fatal injuries!

■

The front passenger airbag must be deactivated if using a rear-facing child seat on the front passenger seat » page 18, Deactivating airbags. If this is not done, there is a risk of the child suffering severe or even fatal injuries if the front passenger airbag is deployed. When transporting a child on the front passenger seat, pay attention to any relevant national regulations regarding the use of child safety seats.

Fig. 9 Safe distance to steering wheel/gas-filled airbags

In the event of a severe frontal collision, the front airbag system offers additional protection for the head and chest area of the driver and front passenger.

The front airbag for the driver is housed in the steering wheel » Fig. 8 - . The front airbag for the front seat passenger is located in the dash panel

above the glove compartment » Fig. 8 - . The airbags inflate in front of the driver and front passenger when they are

deployed » Fig. 9 - . The forward movement of the driver and of the front passenger is cushioned when they make contact with the fully inflated airbag and the risk of injury to head and chest is thus reduced.

Safety

WARNING

General information

■

The steering wheel and the surface of the airbag module in the dash panel on the passenger side must not have stickers attached, be covered or modified in any other way. These parts should only be cleaned with a cloth that is dry or has been moistened with water. No objects such as cup holders, mobile phone mounts, etc. must be attached to the covers of the airbag modules or be located within their immediate vicinity.

■

Never place objects on the surface of the front passenger airbag module in the dash panel.

Page 19

Side airbags

Fig. 10 Location of the side airbag in the driver's seat/gas-filled side airbag

In the event of severe side collisions, the side airbag system provides additional protection for the upper body (chest, stomach and pelvis) of passengers in the vehicle.

The side airbags are housed in the upholstery of the seat backrests of the front seats » Fig. 10 – .

The head airbag and belt tensioner on the relevant side are also automatically deployed when the side airbags » Fig. 10 -  are deployed.

The load of the occupants is cushioned when plunging into the fully inflated airbag and the risk of injury to the entire upper body (chest, stomach and pelvis) is reduced on the side facing the door.

WARNING

Information on correct seated position

■

Your head should never be positioned in the deployment area of the side airbag. You might suffer severe injuries in the event of an accident. This applies in particular to children who are transported without using a suitable child safety seat » page 21, Child safety and side airbag.

■

There must not be any further persons, animals or objects positioned between the occupants and the deployment area of the airbag. No accessories, such as cup holders, should be attached to the doors.

■

If children adopt an incorrect seated position when travelling, they may be exposed to an increased risk of injury in the event of an accident. This can result in serious injuries » page 20, Child seat.

WARNING

■

Only hang light items of clothing on the hooks fitted in the vehicle. Never leave any heavy or sharp-edged objects in the pockets of the items of clothing.

■

Ensure that there are no excessive forces, such as violent knocks, kicks etc., impact on the backrests of the seats otherwise the system may be damaged. The side airbags would not be deployed in such a case!

■

Any seat or protective covers which you fit to the driver or front passenger seats must only be of the type expressly authorized by ŠKODA. In view of the fact that the airbag inflates out of the backrest of the seat, use of non-approved seat or protective covers would considerably impair the protective function of the side airbag.

■

Any damage to the original seat covers in the area of the side airbag module must be repaired immediately by a specialist garage.

■

The airbag modules in the front seats must not display any damage, cracks or deep scratches. It is not permissible to use force in order to open the modules.

Head airbags

Fig. 11 Location of the head airbag/gas-filled head airbag

In the event of a severe side collision, the head airbag system offers additional protection for the head and neck area of passengers.

The head airbags are positioned above the doors on both sides in the interior of the car » Fig. 11 - .

In the event of a side collision the head airbag is deployed together with the relevant side airbag and the front seat belt tensioner on the side of the car on which the accident occurs.



Airbag system

Page 20

The airbag covers the windows of the front and rear doors, as well as the door pillar when it is deployed » Fig. 11 - .

Head impact with interior parts is reduced by the inflated head airbag. The reduction in any impact to the head and the resultant minimizing of any movements of the head additionally reduce the risk of injuries to the neck area.

WARNING

■

There must not be any objects in the deployment area of the head air-

bags which might prevent the airbags from inflating properly.

■

Only hang light items of clothing on the hooks fitted in the vehicle. Never leave any heavy or sharp-edged objects in the pockets of the items of clothing. Additionally, clothes hangers must not be used to hang up items of clothing.

■

The installation of impermissible accessories in the vicinity of the head airbags can considerably impair the protection offered by the head airbag in the event of it being deployed. When the deployed head airbag is inflated, parts of the accessories fitted could be thrown into the interior of the car and injure the occupants » page 128.

■

The sun visors must not be swivelled towards the side windows in the deployment area of the head airbags if any objects, such as ball-point pens, etc. are attached to them. This might result in injuries to the occupants if the head airbag is deployed.

■

There must not be any further persons, animals or objects positioned between the seated occupants and the deployment area of the airbag. In addition, none of the occupants should lean their head out of the window when driving, or extend their arms and hands out of the window.

Note

The word AIRBAG can be seen on the B pillar trim in vehicles with head airbags.

Deactivating airbags



Introduction

This chapter contains information on the following subjects: Deactivating airbags

Deactivating the front passenger airbag 19

Deactivating airbags

Deactivating an airbag should be considered in cases such as the ones below.

If using a rear-facing child seat on the front passenger seat (due to different

›

legal regulations, the airbag must be deactivated if using a forwards-facing child seat in some countries) » page 20, Transporting children safely. If it is not possible to maintain a distance of at least 25 cm between the mid-

›

dle of the steering wheel and chest, despite the driver's seat being correctly adjusted. If special attachments are required in the area of the steering wheel because

›

of a physical disability. If different seats have been fitted (e.g. orthopaedic seats without side air-

›

bags).

The front passenger airbag can be switched off with the key-operated switch » page 19.

We recommend that you ask a ŠKODA service partner to deactivate any other airbags.

Monitoring the airbag system

The operational capability of the airbag system is monitored electronically, including when one of the airbags is switched off.

Airbag deactivated using diagnostic equipment

The warning light  lights up for approx. 3 seconds after switching on the

›

ignition and then flashes again for approx. 12 seconds.

Front passenger airbag deactivated using the key switch in the storage compartment

The warning light  lights up for approx. 3 seconds after switching on the

›

ignition. The

›

is switched on.

■

The national regulations for switching off airbags must be observed.

■

A ŠKODA service partner will be able to inform you which, if any, of your vehi-

cle's airbags can or must be deactivated.

3 » Fig. 12 on page 19 warning light comes on when the ignition

 

Note

Safety

Page 21

Deactivating the front passenger airbag

Fig. 12 Key switch for front passenger airbag/warning light for front passenger airbag activation/deactivation

Only the front passenger airbag is deactivated with the key switch.

Switching off

Switch off the ignition.

›

Open the passenger door.

›

Fold the key bit out completely for the radio key » .

›

Carefully insert the key into the key slot in the key switch as far as the stop.

›

Use the key to turn the slot of the key switch into position 2 » Fig. 12 OFF.

›

Pull the key out of the slot in the key switch » .

›

Close the passenger door.

›

After switching on the ignition, check whether the warning light 3

›

illuminated in writing

Switching on

Switch off the ignition.

›

Open the passenger door.

›

Fold the key bit out completely for the radio key » .

›

Carefully insert the key into the key slot in the key switch as far as the stop.

›

Use the key to turn the slot of the key switch into position 1 » Fig. 12 ON.

›

Pull the key out of the slot in the key switch » .

›

Close the passenger door.

›

After switching on the ignition, check whether the warning light 3

›

not illuminated in writing panel.

    

is illuminated in the centre panel.

is not illuminated in the centre

 

WARNING

■

The driver is responsible for whether the airbag is switched on or switch-

ed off.

■

Only switch off the airbag when the ignition is switched off! Otherwise a

fault can occur in the system for deactivating the airbag.

■

If the warning light be deployed in the event of an accident. Have the airbag system checked by a specialist garage immediately.

■

The key cannot be inserted in the key switch while driving.

■

Shocks can cause the key to turn in the slot and trigger the airbag!

■

The airbag could be triggered unexpectedly in an accident - it may result

in injury or death!

CAUTION

An insufficiently folded out key bit can damage the key switch!

 

flashes, then the front passenger airbag will not

The warning light   comes on for a few seconds after the ignition is switched on, goes out for about 1 second and then comes on again.

Airbag system

Page 22

Transporting children safely

Child seat

Introduction



This chapter contains information on the following subjects: Use of a child seat on the front passenger seat 20

Child safety and side airbag 21 Classification of child seats 22 Use of child seats fastened with a seat belt 22

Children are generally safer on the rear seats than on the front passenger seat.

In contrast to adults, the muscles and bone structure of children are not yet fully developed. Thus children are exposed to increased risk of injury.

Children should be transported in accordance with the relevant statutory provisions.

Child seats that comply with the ECE-R 44 standard must be used. The ECE-R standard stands for: Economic Commission for Europe - Regulation.

Child seats that comply with the ECE-R 44 standard are identified with a test mark that cannot be removed: a large E within a circle with the test number below.

WARNING

■

The national legal requirements must be observed when using child

seats.

■

One should never carry children, and also not babies! - on one's lap.

■

Never leave children unattended in the vehicle. Certain outside climatic

conditions can cause life-threatening temperatures in the vehicle.

■

The child must be secured in the vehicle during the entire journey! Otherwise, the child would be thrown through the vehicle in the event of an accident, causing fatal injuries to both the child and other occupants.

■

Children are exposed to an increased risk of injury in the event of an accident if they lean forward or adopt an incorrect seated position when the vehicle is moving. This particularly applies to children who are transported on the front passenger seat as they can suffer severe, or even fatal injuries if the airbag system is deployed!

WARNING (Continued)

■

Pay particular attention to the information provided by the manufacturer of the child safety seat regarding the correct routing of the belt. Seat belts which are not correctly adjusted can themselves cause injuries even in minor accidents.

■

Safety belts must be checked to ensure that they are running properly. One should also ensure that the belt is not damaged by sharp-edged fittings.

■

The front passenger airbag must be deactivated if using a rear-facing child seat on the front passenger seat. Further information » page 20, Use of a child seat on the front passenger seat.

Note

We recommend that you use child seats from ŠKODA Original Accessories. These child seats were developed and also tested for use in ŠKODA vehicles. They meet the ECE-R 44 standard.

Use of a child seat on the front passenger seat

Never use a backwards-facing child restraint system on a seat that is protected by an active airbag installed in front of it. This could cause the child severe injury or even death.

Fig. 13

Sticker on the B column on the front passenger side.



Safety

Page 23

Fig. 14

Front passenger sun visor / sticker

Read and observe on page 20 first.



For safety reasons, we recommend that you install child seats on the rear seats whenever possible.

The following instructions must be followed when using a child seat on the front passenger seat.

The front passenger airbag must be deactivated if using a rear-facing child

›

seat » . If possible, adjust the front passenger seat backrest so that it is as vertical,

›

so as to ensure secure contact between the passenger seat backrest and the back of the child seat. If possible, move the front passenger seat backwards so that there is no con-

›

tact between the front passenger seat and the child seat behind it. With child safety seats in groups 2 or 3, make sure that the loop-around fit-

›

tings attached to the child seat headrest is positioned in front of or at the same height as the loop-around fittings on the B pillar on the passenger side. Set the height-adjustable front passenger seat as high up as possible.

›

Set the front passenger seat belt as high up as possible.

›

Place and fasten the child seat on the seat and the child in the child seat ac-

›

cording to the specifications in the manufacturer's user manual of the child seat .

WARNING

■

The front passenger airbag must be deactivated if using a rear-facing

child seat on the front passenger seat » page 18, Deactivating airbags.

■

Never use a rear-facing child seat on the front passenger seat if the passenger airbag is activated. This child safety seat is positioned in the deployment area of the front passenger airbag. The airbag may cause the child severe, or even fatal injuries, in the event of it being deployed.

■

This fact is also indicated by the sticker that can be found in one of the following locations.

■

On the B-column on the front passenger side » Fig. 13. The sticker is

visible upon opening the front passenger door.

■

On the front passenger's sun visor. In some countries, the sticker is lo-

cated on the front passenger's sun visor » Fig. 14.

■

With child safety seats in groups 2 or 3, make sure that the loop-around fittings attached to the child seat headrest is positioned in front of or at the same height as the loop-around fittings on the B pillar on the passenger side.

■

As soon as the rear-facing child seat is no longer being used on the passenger seat, the front passenger airbag should be re-activated again.

Child safety and side airbag

Fig. 15

Incorrect seated position of a child who is not properly secured – risk from the side airbag/Child properly protected by safety seat

Read and observe on page 20 first.



The child must not be positioned in the area into which the side airbag will deploy » Fig. 15 - .

There must be sufficient room between the child and the area into which the side airbag will deploy to allow the airbag to provide as much protection as possible » Fig. 15 - .



Transporting children safely

Page 24

WARNING

■

Children must never be seated with their head in the deployment area of

the side airbag – risk of injury!

■

Do not place any objects within the deployment area of the side airbags –

risk of injury!

Classification of child seats

Read and observe on page 20 first.



Classification of child seats according to the ECE-R 44 standard.

Group Weight of the child Approximate age

0 up to 10 kg up to 9 months

0 + up to 13 kg up to 18 months

1 9-18 kg up to 4 years 2 15-25 kg up to 7 years

3 22-36 kg over 7 years

Use of child seats fastened with a seat belt

Read and observe



Overview of the usability of child seats fastened with a seat belt on each of the seats in accordance with the ECE-R 16 standard.

Group

up to 10 kg

0 +

up to 13 kg

9-18 kg

15-25 kg

22-36 kg

Front passenger

on page 20 first.

seat

U U U

Rear seats

outside

Rear seat

centre

Child seat category “Universal” - a child seat designed to be attached to

the seat using the seat belt.

Fastening systems

Introduction



This chapter contains information on the following subjects: Anchor eyelets for the ISOFIX system 22

Use of child seats with the ISOFIX system 23 Anchor eyelets for the TOP TETHER system 23

Anchor eyelets for the ISOFIX system

Fig. 16

ISOFIX system label

There are two locking eyes between the rear exterior seats for fixing the ISOFIX system child seat in place.

The places are marked with labels with the ISOFIX logo » Fig. 16.

WARNING

■

Always refer to the instructions from the manufacturer of the child seat

when installing and removing a child seat with the ISOFIX system.

■

Never attach other child seats, belts or objects to the anchor eyelets intended for the installation of a child seat with the ISOFIX system – risk to life!



Safety

Page 25

Note

■

A child seat fitted with the ISOFIX system can only be mounted in a vehicle fitted with an ISOFIX system if the child seat has been approved for this type of vehicle. Further information is available from a ŠKODA Partner.

■

Child seats with the ISOFIX system can be purchased from ŠKODA Original Accessories.

Use of child seats with the ISOFIX system

Overview of the usability of child seats with the ISOFIX system on each of the seats in accordance with the ECE-R 16 standard.

Group

up to 10 kg

0 +

up to 13 kg

Size class

of the child seat

Front passenger seat

E X IL-SU X

X IL-SU XD

Outer rear seats Rear seat middle

9-18 kg

C B

IL-SU

IUF

The size category is shown on the label attached to the child seat.

If the front passenger seat is fitted with the ISOFIX system attachment points, it is suited for the installation of an ISOFIX child seat with the “Semi-Universal” approval.

The seat is suited for installation of an ISOFIX child seat with “Semi-

IL-SU

Universal” approval. The category “Semi-Universal” means that the child

Anchor eyelets for the TOP TETHER system

seat with the ISOFIX system is approved for your vehicle. Observe the list of vehicles that comes with the child seat.

The seat is suitable for the installation of an ISOFIX child seat with

IUF

“Universal” approval and attachment with the TOP TETHER belt. The seat is not fitted with fixing eyes for the ISOFIX system.

Fig. 17

Anchor eyelets for the TOP TETHER system

Transporting children safely



Page 26

The anchor eyelets for attaching the belt for a child seat with the TOP TETHER system are located on the rear side of the outer rear seat backrests » Fig. 17.

WARNING

■

Always refer to the instructions from the manufacturer of the child seat

when installing and removing a child seat with the TOP TETHER system.

■

Only use child seats with the TOP TETHER system on the seats with the

locking eyes.

■

Only ever attach one belt from the child seat to a locking eye.

■

On no account should you equip your vehicle, e.g. mount screws or other

anchorage points.

Safety

Page 27

Transporting children safely

Page 28

Fig. 18 Cockpit

Operation

Page 29

Operation

Cockpit

Overview

Door opening lever 46

Electrical power windows 53

Electric exterior mirror adjustment 65

Air outlet vents 87

Parking ticket holder 80

Operating lever:

Turn signal light, headlight and parking light, headlight

›

flasher 58 Speed regulating system 118

›

Steering wheel:

With horn

›

With driver’s front airbag 16

›

With pushbuttons for radio, navigation system and mobile

›

phone 94

Instrument cluster: Instruments and warning lights 28

Operating lever:

Windscreen wiper and wash system 63

›

Multifunction display 31

›

MAXI DOT display 35

›

Button for rear window heater 61

TCS switch

Air outlet vents in the central part of the dash panel 87

Button for hazard warning light system 60

Warning light for the deactivated front seat passenger airbag 19

Depending on equipment fitted:

Operating controls for the heating 88

›

Operating controls for the air conditioning system 90

›

Operating controls for Climatronic 92

›

Storage compartments on the front passenger side 81

Front passenger airbag 16

Air outlet vents 87

Key-operated switch for the front seat passenger airbag 19

Door opening lever 46

Switch depending on equipment fitted:

Boot lid remote release 53

›

Interior monitor 52

›

Light switch and headlamp beam adjustment 56, 57

Fuse box in the dashboard 168

Bonnet release lever 141

Lever for adjusting the steering wheel 8

Ignition lock 104

Pedals 106

Depending on equipment fitted:

Gearshift lever (manual gearbox) 106

›

Selector lever (automatic gearbox) 107

›

Rocker switch for front left seat heating 66

Central locking system 49

Handbrake 106

Rocker switch for front right seat heating 66

Depending on equipment fitted:

Ashtrays 78

›

Storage compartment 82

›

Depending on equipment fitted:

Radio

›

Navigation system

›

MDI 101

117

Note

The arrangement of the controls right-hand drive models may differ from the layout shown in » Fig. 18. The symbols on the controls and switches are the same as for left-hand drive models.

Cockpit

Page 30

Instruments and Indicator Lights

Instrument cluster

Introduction



This chapter contains information on the following subjects: Overview 28

Engine revolutions counter 29 Speedometer 29 Coolant temperature gauge display 29 Fuel gauge 29 Counter for distance driven 30 Digital clock 30 Display of the second speed 30 Recommended gear 30

Fault display

The Error message will appear in the display if there is a fault in the instrument cluster. Ensure that the fault is rectified as soon as possible by a specialist workshop.

WARNING

■

Concentrate fully at all times on your driving! As the driver you are fully

responsible for road safety.

■

Never operate the controls in the instrument cluster while driving, only

when the vehicle is stationary!

Overview

Fig. 19 Instrument cluster

Read and observe on page 28 first.



Revolutions counter with warning lights » page 29

Display:

With counter for distance driven » page 30

›

With service interval display » page 34

›

With digital clock » page 30

›

With multifunction display (MFD) » page 31

›

With the MAXI DOT display » page 35

›

Speedometer with warning lights » page 29

Coolant temperature gauge1) » page 29

Button for display mode:

Set the hours/minutes » page 30

›

Enable/disable the display of the second speed2) » page 30

›

Service interval2) - Display of the number of days, kilometres or miles re-

›

maining until the next Service3) » page 34



Applies for vehicles using the MAXI DOT display.

Applies for vehicles with a segment display.

Applies for models in which where the values are indicated in British measuring units.

Operation

Page 31

Button for:

Reset trip meter » page 30

›

Set hours/minutes

›

Enable/disable the mode selected by means of button

›

Fuel gauge1) » page 29

Engine revolutions counter

Read and observe on page 28 first.



The red scale range of the rev counter 1 » Fig. 19 on page 28 indicates the range in which the engine control unit begins to limit the engine speed. The engine control unit restricts the engine speed to a steady limit.

You should shift into the next higher gear before the red scale of the revolution counter is reached, or move the selector lever into position D if your car is fitted with an automatic gearbox.

To maintain the optimum motor speed, observe the gearshift indicator » page 30.

For the sake of the environment

Shifting up in good time has the following benefits.

■

It helps to reduce fuel consumption.

■

It reduces engine noise.

■

It protects the environment.

■

It benefits the life and reliability of the engine.

Speedometer

Read and observe



Warning against speeding

An audible warning will sound when the vehicle speed exceeds 120 km/h2). The audible warning is switched off once the vehicle speed falls below 120 km/h.

on page 28 first.

Coolant temperature gauge display

Read and observe on page 28 first.



The coolant temperature gauge 4 » Fig. 19 on page 28 works only when the ignition is switched on.

In vehicles with a segment display, the coolant temperature is indicated only by one of the warning lights » page 39,   Coolant coming on or going off.

Cold range

The pointer in the left of the scale indicates that the engine has not yet reached its operating temperature. Avoid high speeds, full throttle and high engine loads. This prevents possible damage to the engine.

The operating range

The engine has reached its operating temperature as soon as the pointer moves into the middle of the scale. At very high ambient temperatures or under heavy engine loads, the pointer may move even further to the right.

High temperature range

The coolant temperature is too high if the pointer reaches the red area of the scale. Further information » page 39.

CAUTION

■

Additional headlights and other attached components in front of the air inlet

impair the cooling efficiency of the coolant.

■

Never cover the radiator - there is a risk of the engine overheating.

Fuel gauge

Read and observe



The fuel gauge 7 » Fig. 19 on page 28 only works when the ignition is switched on.

The fuel remaining is displayed in the segment display on vehicles with the segment display.

The fuel tank has a capacity of about 45 litres. The warning light lights up when the fuel level reaches the reserve range  » page 42.

on page 28 first.



Applies for vehicles using the MAXI DOT display.

This function is only enabled in certain countries.

Instruments and Indicator Lights

Page 32

CAUTION

Never drive until the fuel tank is completely empty! The irregular supply of fuel can cause misfiring. This can result in considerable damage to parts of the engine and the exhaust system.

Counter for distance driven

Read and observe on page 28 first.



The distance which you have driven with your vehicle is shown in km. In some countries the measuring unit “mile” is used.

Daily trip counter (trip)

The trip counter indicates the distance you have driven since it was last reset in steps of 100 metres or 1/10 of a mile.

Reset trip meter

The meter can be reset by pressing and holding button 6 » Fig. 19 on page 28.

Odometer

The odometer indicates the total distance in kilometres or miles which the vehicle has been driven.

Note

If the second speed display is enabled on vehicles with a segment display, this speed will be shown instead of the odometer.

Digital clock

Read and observe on page 28 first.



The clock is set with buttons 5 and 6 » Fig. 19 on page 28. Select the display that you wish to change with the button 5 and carry out

the change with the button 6. In vehicles equipped with the MAXI DOT display, it is also possible to set the

clock in the Time menu » page 36.

Display of the second speed

Read and observe on page 28 first.



The display can show the current speed in mph1). This feature is provided for driving in countries with different units for speed.

MAXI DOT display

The display of the second speed can be set in the Settings menu item » page 36, Settings.

Segment display

Press the 5 » Fig. 19 on page 28key repeatedly, until the odometer display

›

flashes » page 30. Press the 6 key while the display is flashing.

›

The second speed is displayed instead of the odometer. Display of the second speed can be disabled in the same way.

Recommended gear

Fig. 20

Recommended gear

Read and observe on page 28 first.



The gear currently engaged is shown in the instrument cluster display

» Fig. 20.

In order to minimise the fuel consumption, a recommendation for shifting into another gear is indicated in the display.



On models on which the speedometer indicates mph, the second speed is displayed in km/h.

Operation

Page 33

If the control unit recognises that it is beneficial to change gear, an arrow B is shown in the display. The arrow points up or down, depending on whether you should shift into a higher or lower gear.

At the same time, the recommended gear is shown at A instead of the gear

selected on vehicles with a manual gearbox.

CAUTION

The driver is always responsible for selecting the correct gear in different driving situations, such as overtaking.

Multifunction display (MFD)

Introduction



This chapter contains information on the following subjects: Memory 31

Operation Multifunction display details Warning against speeding

The multifunction display can only be operated when the ignition is switched on. After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.

The multifunction display shown in the segment display » Fig. 21 on page 31 or in the MAXI DOT display depending on your vehicle model » page 35.

On vehicles with a MAXI DOT display » page 35, there is an option not to display some of the information.

WARNING

■

Concentrate fully on your driving at all times. As the driver you are fully

responsible for the operation of your vehicle.

■

Even at temperatures of around +4 °C, there may still be black ice on the road surface. You should therefore not rely solely on the outside temperature display for accurate information as to whether there is ice on the road.

Note

■

In certain national versions the displays appear in the Imperial system of

measures.

■

If the display of the second speed is activated in mph, the current speed is

not indicated in km/h on the display.

32 32 33

Memory

Fig. 21

Multifunction display

Read and observe on page 31 first.



The multifunction display is equipped with two automatic memories. The selected memory is shown in the Display » Fig. 21.

The data of the single-trip memory (memory 1) is shown if a 1 appears in the display. A 2 shown in the display means that data relates to the total distance memory (memory 2).

Switch memories using button B » Fig. 22 on page 32 on the windscreen wiper stalk.

Single-trip memory (memory 1)

The single-trip memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued within 2

hours after switching off the ignition. If the trip is interrupted for more than 2 hours, the memory is automatically erased.

Total-trip memory (memory 2)

The total trip memory collates the data from any number of individual trips up to a total of 19 hours and 59 minutes or 1999 km or, for vehicles with a MAXI DOT display, 99 hours and 59 minutes, or 9999 km. The memory is deleted when either of these limits is reached and the calculation starts all over again.

Unlike the single-trip memory, the total-trip memory is not deleted after a period of interruption of driving of 2 hours.

Note

All information in the memory 1 and 2 is erased if the battery of the vehicle is disconnected.

Instruments and Indicator Lights

Page 34

Operation

Fig. 22

Multifunction display: Control elements

Read and observe on page 31 first.



The Toggle button for selecting menu items A » Fig. 22 and button B are found on the wiper stalk.

Select menu items

Briefly press the top or bottom of rocker switch A » Fig. 22. This opens the

›

individual menu items in the multifunction display one after the other.

Select memory

Press button B » Fig. 22.

›

Reset memory

Select the desired memory.

›

Press and hold button B » Fig. 22.

›

The following values from the memory selected will be set to zero by button

Average fuel consumption.

›

Distance driven.

›

Average speed.

›

Driving time

›

Multifunction display details

Read and observe on page 31 first.



Outside temperature

The current outside temperature is displayed1). The temperature is shown with the snowflake symbol  if the outside temper-

ature is below +4 °C. This display flashes for a few seconds, then shows the most recently displayed

function2) . If the temperature drops below +4 °C while the car is driving at a speed faster

than 10 km / h, a beep is also heard.

Driving time

The driving time elapsed since the memory was last erased appears in the display. Reset the memory to zero by pressing the button » page 32, Operation to measure the driving time from a particular moment.

The maximum time indicated in both memories is 19 hours and 59 minutes and on vehicles which are fitted with a MAXI DOT display, it is 99 hours and 59 minutes. The indicator is set back to zero when this period is exceeded.

Current fuel consumption

The current fuel consumption level is displayed in litres/100 km3). You can use this information to adapt your driving style to the desired fuel consumption.

The display appears in litres/hour if the vehicle is stationary or driving at a low speed4).

Average fuel consumption

The average fuel consumption since the memory was last erased is displayed in litres/100 km3).

Set the memory to zero at the start of a new measurement if you wish to determine the average fuel consumption over a certain period » page 32, Opera- tion. No value will appear in the display after it has been erased until you have driven approximately 300 m.



This information is always shown on vehicles with a MAXI DOT display.

This is not the case on the MAXI DOT display.

On some models in certain countries, the display appears in kilometres/litre.

On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is stationary.

Operation

Page 35

The display is updated regularly while you are driving.

Range

The estimated range is displayed in kilometres. It indicates the distance you can still drive with your vehicle based on the level of fuel in the tank and the same style of driving.

The display is shown in steps of 10 km. The value is displayed in steps of 5 km after the  has come on.

The fuel consumption over the preceding 50 km is used to calculate the information. The range will increase if you drive in a more economical manner.

If the memory is set to zero (after the battery has been disconnected), a fuel consumption of 10 l/100 km is used initially, then the value is adapted according to the style of driving.

Distance travelled

The distance travelled since the memory was last erased is displayed. Reset the memory to zero if you want to measure the distance travelled from a particular moment » page 32, Operation.

The maximum distance indicated in both memories is 1999 km or 9999 km on vehicles with a MAXI DOT display. The indicator is set back to zero when this period is exceeded.

Average speed

The average speed since the memory was last erased is displayed in km/hour . Set the memory to zero at the start of measurement to determine the average speed over a certain period » page 32, Operation.

No value will appear in the display until you have driven approximately 300 m after this information has been deleted.

The display is updated regularly while you are driving.

Current speed

The current speed, identical to the display on the speedometer 3 » Fig. 19 on page 28, is displayed.

Oil temperature

The current engine oil temperature is displayed. If the oil temperature is lower than 50 °C or if a fault in the system for checking the oil temperature is present, only - -.- is displayed instead of the oil temperature.

Warning against speeding

The warning that the speed limit is being exceeded can be enabled/disabled in the display» page 33.

Warning against speeding

Read and observe on page 31 first.



Adjust the speed limit while the vehicle is stationary

Press button A » Fig. 22 on page 32 to select the Warning at (MAXI DOT

›

display) or  (segment display) menu item. Press button B to activate the ability to set the speed limit2) (value flashes).

›

Use button A to set the required speed limit, e.g. 50 km/h.

›

Confirm the speed limit that was set with button B, or wait approx. 5 sec-

›

onds until the setting is saved automatically (the value stops flashing).

This allows you to set the speed in 5 km/h intervals.

Adjusting the speed limit while the vehicle is moving

Press button A » Fig. 22 on page 32 to select the Warning at (MAXI DOT

›

display) or  (segment display) menu item. Drive at the desired speed, e.g. 50 km/h.

›

Press button B to accept the current speed as the speed limit (the value

›

flashes).

If you wish to adjust the set speed limit, you can do so in 5 km/h intervals (e.g. the accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).

Confirm the speed limit that was set by pressing button B again, or wait ap-

›

prox. 5 seconds until the setting is saved automatically (the value stops flashing).

Change or delete speed limit

Press button A » Fig. 22 on page 32 to select the Warning at (MAXI DOT

›

display) or  (segment display) menu item. Pressing button B disables the speed limit.

›

Pressing the button B activates the ability to change the speed limit.

›

If the set speed limit is exceeded, an audible signal will sound as a warning. The Warning at (MAXI DOT display) or  (segment display) menu item appears in the display with the limit set.



Applies for vehicles using the MAXI DOT display.

An initial value of 30 km/h is displayed automatically if no value has been specified.

Instruments and Indicator Lights

Page 36

The speed limit set mode is stored even after the ignition is switched off and on.

Service Interval Display

Introduction



This chapter contains information on the following subjects: Prompt in the segment display 34

Display in the MAXI DOT display 34 Resetting the service interval display 35

The service interval display shows the time and mileage to the next service event.

The service due date is automatically displayed on the display and this information can be displayed manually at any time if necessary.

The kilometre indicator or the days indicator reduces in steps of 100 km or days until the service due date is reached.

The information regarding the service intervals can be found in the service schedule.

Note

Information is retained in the Service Interval Display even after the vehicle battery is disconnected.

Prompt in the segment display

Fig. 23

Example of a message

Oil change service

If an oil change service is due, the  icon and the number 1 is displayed at the position identified with the arrow for approximately 10 seconds » Fig. 23.

The  icon is shown together with the days and kilometres remaining to the next service.

As soon as the service due date is reached, the flashing  icon and the message OIL CHNG appears in the display for about 20 seconds after the ignition is switched on.

Inspection

If an inspection is due, the  icon and the number 2 are displayed at the position identified with the arrow for approximately 10 seconds » Fig. 23.

The  icon is shown together with the days and kilometres remaining to the next service.

As soon as the due date for the service is reached, the flashing  icon and the INSPEC _ message appear in the display for about 20 seconds after the ignition has been switched on.

Display the days and distance until the next service

You can press button 5 » Fig. 19 on page 28 repeatedly to display the remaining distance and time to until the next service whenever the ignition is switched on.

The  icon appears together with the  icon and the distance and time to the next service appear in the display for about 10 seconds.

The distance and the days remaining until the next oil change service are displayed first; the distance and the days remaining until the next inspection are displayed after the button 5is pressed again.

Note

The kilometres remaining until the next service are displayed instead of the odometer.

Display in the MAXI DOT display

Oil change service

If an oil change service is due, the message Oil change in ... km or .... days.

As soon as the service date has arrived, the message Oil change now! appears after the ignition is switched on.

Inspection

If an inspection is due, the message Inspection in ... km or ... days. As soon as the service interval date has arrived, the message Inspection now!

appears after the ignition is switched on.



Operation

Page 37

Displaying the distance and days until the next service interval

You can display the remaining distance and days until the next service in the Settings menu whenever the ignition is switched on » page 36.

The following message is displayed for 10 seconds.

Oil change ... km / ... days Inspection ... km / ... days

Resetting the service interval display

We recommend that the display reset is completed by a specialist garage.

We recommend that you do not reset the service interval display yourself. Incorrectly setting the service interval display could cause problems to the vehicle.

Variable service interval

For vehicles with variable service intervals, after resetting the oil change service display, the values of a new service interval are displayed, which are based on the previous operating conditions of the vehicle.

These values are then continuously matched according to the actual operating conditions of the vehicle.

MAXI DOT display



Introduction

This chapter contains information on the following subjects: Main menu

Settings Door, boot lid and bonnet warning Auto Check Control

The MAXI DOT display provides you with information about the current operat- ing state of your vehicle. The information system also provides you with data (depending on the vehicle equipment) relating to the radio, mobile phone, multi-functional display, navigation system, the device connected to the MDI input and the automatic gearbox » page 107.

Lighting up of certain symbols is combined with an acoustic warning signal.

35 36 36 36

WARNING

Concentrate fully on your driving at all times. As the driver you are fully responsible for the operation of your vehicle.

Main menu

Fig. 24

Operating lever: MAXI DOT display controls

Read and observe on page 35 first.



Press and hold rocker switch A » Fig. 24 to activate the MAIN MENU.

›

Individual menu items can be selected by pressing rocker switch A. When

›

the pushbutton B is briefly pressed, the information you have selected is displayed.

Overview of the menu items in the main menu.

■

MFD (Multifunction display) » page 31

■

Audio » Operating instructions for the radio

■

Navigation » Operating instructions for the navigation system

■

Phone » page 94;

■

Vehicle status » page 36

■

Settings » page 36

The Audio and Navigation menu items are only displayed when the factory-fitted radio or navigation system is switched on.

Note

■

Warning messages shown in the information display must be confirmed by

pressing button B briefly » Fig. 24 to call up the main menu.

■

The menu always shifts to one of the higher levels after 10 seconds if the

display is not currently active.

■

Using the factory-fitted radio or navigation system » Radio operating in-

structions or» Navigation system operating instructions.

Instruments and Indicator Lights

Page 38

Settings

Read and observe on page 35 first.



You can change certain settings yourself through the MAXI DOT display. The current menu item is shown in the top of the display under a line.

You can select the following menu options:

Language

You can set the language for the warning and information texts here.

MFD data

Activate or deactivate certain displays of the multifunction display here.

Time

The time, time format (12 or 24 hour indicator) and the changeover between summer/winter time can be set here.

Winter tyres

Here, you can set the speed at which an audible signal should sound. This function is, for example, used for winter tyres where the maximum permissible speed is lower than the maximum speed of the vehicle.

The following is shown on the information display if this speed is exceeded:

Winter tyres: maximum ... km/h.

Units of measurement

The units for the temperature, consumption and distance driven can be set here.

Alt. speed dis.

Display of the second speed in mph1) can be activated here.

Service

The days and kilometres remaining until the next service can be displayed here.

Factory setting

The display can be restored to its factory settings here.

Door, boot lid and bonnet warning

Read and observe on page 35 first.



If at least one door is open, or the boot or bonnet is open, the MAXI DOT display shows the vehicle with the corresponding door or boot/bonnet open.

An audible signal also sounds if the vehicle is travelling at more than 6 km/h.

Auto Check Control

Read and observe on page 35 first.



Vehicle condition

Certain functions and conditions of individual vehicle systems are checked continuously when the ignition is switched on and also while driving.

Some error messages and other information are displayed in the MAXI DOT display. The messages are displayed simultaneously with the icons in the MAXI DOT display or with the warning lights in the instrument cluster » page 37.

The Vehicle status menu item is shown in the main menu of the MAXI DOT display whenever at least one fault message is present. The first of the fault messages is displayed after this menu item is selected. Several error messages are shown on the display under the message e.g. 1/3. This indicates that the first of a total of three error messages is being displayed.

As long as the operational faults are not rectified, the symbols are always indicated again. After they are displayed for the first time, the symbols continue to be indicated without any extra messages for the driver.

Warning symbols







Clutches of the automatic DSG gearbox are too hot



If the  symbol appears in the MAXI DOT display, this indicates that the temperature of the automatic DSG gearbox clutches is too high.

Engine oil pressure too low » page 38

Clutches of the automatic DSG gearbox are too hot

Check engine oil level, engine oil sensor defective

» page 36

» page 38



On models on which the speedometer indicates mph, the second speed is displayed in km/h.

Operation

Page 39

The following message is shown in the MAXI DOT display.

Gearbox overheated. Stop. Log book!



Stop the vehicle, switch off the engine, and wait until the icon goes out – there is a risk of gearbox damage. You can continue your journey as soon as the icon disappears.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 60.

Note

■

Warning messages shown in the MAXI DOT display must be confirmed with

button B » Fig. 24 on page 35 to call up the main menu.

■

Warning lights



Introduction

This chapter contains information on the following subjects:



Handbrake 37



Brake system 38



Seat belt warning light 38



Generator 38



Open door 38

 

Engine oil 38

 

Coolant 39



Power steering 40



Electronic Stability Control (ESC) 40



Traction Control System (ASR) 40



Anti-lock brake system (ABS) 40



The rear fog light 41



Bulb failure 41



Exhaust inspection system 41



Glow plug system (diesel engine) 41

 EPC fault light (petrol engine) 41

 Diesel particulate filter (diesel engine) 41



Fuel reserve 42



Airbag system 42



Tyre pressure 43



Windscreen washer fluid level 43



Traction control (TCS) switched off

 

Turn signal system 43



Low beam 43



Fog lights 43



Cruise control system 43 Selector lever lock 44



Main beam 44



The warning lights show certain functions/faults and may be accompanied by audible signals.

WARNING

■

If illuminated warning lights and the corresponding descriptions and warning notes are not observed, this may result in severe injuries or major vehicle damage.

■

The engine compartment of your car is a hazardous area. There is a risk of injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is essential to observe safety notes » page 140, Engine compartment.



Handbrake

Read and observe



The warning light  comes on if the handbrake is applied. An audible warning is also given if you drive the vehicle for at least 3 seconds at a speed of more than 6 km/h.

The following message is shown in the MAXI DOT display.



Release parking brake!

on page 37 first.

Instruments and Indicator Lights

Page 40

 Brake system

Read and observe on page 37 first.



The  indicator light comes on if the brake fluid level in the braking system is too low or there is a fault in the ABS.

The following message is shown in the MAXI DOT display.



Brake fluid: Log book!

Stop the vehicle, switch off the engine, and check the level of the brake fluid » page 147.

Further information » page 105, Brakes.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 60.

■

The following guidelines should be observed when opening the bonnet and checking the brake fluid level » page 140, Engine compartment.

■

If the warning light  is displayed simultaneously with warning light



» page 40,  Anti-lock brake system (ABS),  do not continue your

journey! Seek help from a specialist garage.

■

A fault to the ABS system or the braking system can increase the vehicle's braking distance – there is a risk of accident.



Seat belt warning light

Read and observe on page 37 first.



The  indicator light comes on after the ignition is switched on as a reminder for the driver and front passenger to fasten their seat belt. The indicator light only goes out once the driver and front passenger have fastened their seat belt.

A steady warning signal sounds at vehicle speeds greater than 20 km/h and the  flashes if the driver and front passenger have not fastened their seat belts.

The warning signal is switched of and the  indicator light is permanently lit if the driver and front passenger have not fastened their seat belts within the next 90 seconds.

Further information » page 10.



Generator

Read and observe on page 37 first.



If the warning light lights up  when the engine is running, the vehicle battery is not being charged.

Seek help from a specialist garage. The electrical system requires checking.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 60.

CAUTION

 Do not continue driving if the  warning light (coolant system fault) lights

up in addition to the  warning light while you are driving. Stop the engine there is a risk of engine damage.



Open door

Read and observe on page 37 first.



The warning light  comes on if one or several doors are opened or if the boot lid is opened.

The warning light comes on even when the ignition is switched off. The warning light lights up for a maximum of 5 minutes.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 60.

  Engine oil

Read and observe on page 37 first.



The warning light  lights up red (low oil pressure)

The following message is shown in the MAXI DOT display.

Oil pressure: Engine off. Log book!





Operation

Page 41

The  warning light comes on for a few seconds when the ignition is switched on1).

Stop the vehicle, switch off the engine, and check the engine oil level » page 144.

Even if the oil level is correct,  do not drive any further if the warning light is flashing. Also do not leave the engine running at an idling speed.

Seek help from a specialist garage.

The warning light  lights up yellow (oil quantity too low)

The following message is shown in the MAXI DOT display.

Check oil level!



Stop the vehicle, switch off the engine, and check the engine oil level » page 144.

An audible signal sounds as a warning signal. The warning light will go out if the bonnet is left open for more than 30 sec-

onds. If no engine oil has been replenished, the warning light will come on again after driving about 100 km.

The warning light  flashes yellow (engine oil level sensor faulty)

The following message is shown in the MAXI DOT display.

Oil sensor workshop!



If the engine oil level sensor is faulty, the warning light flashes  several times and an audible signal sounds when the ignition is turned on.

Seek help from a specialist garage.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 60.

CAUTION

The red oil pressure light  is not an oil level indicator! One should therefore check the oil level at regular intervals, preferably after every refuelling stop.

  Coolant

Read and observe on page 37 first.



The  indicator light remains lit until the engine reaches operating temperature2). Avoid high speeds, full throttle and high engine loads.

If the warning light  lights up or flashes, either the coolant temperature is too high or the coolant level is too low.

An audible signal sounds as a warning tone. The following message is shown in the MAXI DOT display.



Check engine coolant! Log book!

Stop the vehicle, switch off the engine, check the level of the coolant » page 146, and refill the coolant if necessary » page 146.

If the coolant is within the specified range, the increased temperature may be caused by an operating problem at the radiator fan. Check the fuse for the radiator fan, replace if necessary » page 170, Fuses in the engine compartment.

Do not continue driving if the warning light   does not go off even though

the coolant level is correct and the fuse for the fan is in working order!

Seek help from a specialist garage.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 60.

■

Carefully open the coolant expansion bottle. If the engine is hot, the cooling system is pressurized - risk of scalding! It is therefore best to allow the engine to cool down before removing the cap.

■

Do not touch the radiator fan. The radiator fan may switch itself on automatically even if the ignition is off.

CAUTION

■

Additional headlights and other attached components in front of the air inlet

impair the cooling efficiency of the coolant.

■

Never cover the radiator - there is a risk of the engine overheating.

The  warning light does not light up in vehicles fitted with the MAXI DOT display when the ignition is switched on, but only if there is a fault or the engine oil level is too low.

Not on vehicles with the MAXI DOT display.

Instruments and Indicator Lights

Page 42

 Power steering

Read and observe on page 37 first.



The warning light  comes on for a few seconds when the ignition is switched on.

If the warning light after switching on the ignition or when driving lights up continuously, a fault exists in the electrohydraulic power steering. The power steering operates with reduced steering assist or does not function at all.

Seek help from a specialist garage.

Note

■

If the yellow warning light  goes out after starting the engine again and

driving a short distance, it is not necessary to visit a specialist garage.

■

If the vehicle battery has been disconnected and reconnected, the yellow warning light  comes on after switching on the ignition. The warning light should go out after driving a short distance.

■

There is no power-assisted steering support when the vehicle is being towed without the engine running or when the power-assisted steering is defect. The vehicle is fully steerable however. There is however increased force required to turn the steering wheel.



Electronic Stability Control (ESC)

Read and observe



The warning light flashes to show that the ESC is currently operating. If the warning light  comes on immediately after you start the engine, the

ESC might be switched off due to technical reasons. Switch the ignition off and on again. The ESC is fully functional again if the  warning light does not light up after you switch the engine back on.

There is a fault in the ESC system if the  warning light lights up. The following message is shown in the MAXI DOT display.



Error: Electronic Stability Control (ESC)

Seek help from a specialist garage. The ESC system cannot be turned off, the  » page 117 button only switches

the TCS off, the  warning light in the instrument cluster lights up.

on page 37 first.

As the ESC operates in conjunction with the ABS, the ESP indicator light will also come on if the ABS system fails.

Further information » page 116, Electronic Stability Control (ESC).

Note

The  warning light comes on after the ignition is switched on if the vehicle's battery has been disconnected and reconnected. The warning light should go out after the vehicle has driven a short distance.



Traction Control System (ASR)

Read and observe on page 37 first.



The warning light flashes to show that the ASR is currently operating. If the warning light  comes on immediately after starting the engine, the ASR

can be switched off for technical reasons. Switch the ignition off and on again. The TCS is fully functional again if the  warning light does not light up after you switch the engine back on.

If the warning light  lights up, there is a fault in the ASR. The following message is shown in the MAXI DOT display.

Error: Traction control (TSC)



Seek help from a specialist garage. The fact that the TCS system operates together with the ABS means that the

TCS warning light will also come on if the ABS system is not operating properly.

Further information » page 117, Traction Control System (ASR).

Note



Anti-lock brake system (ABS)

Read and observe on page 37 first.



If the warning light  lights up, there is a fault in the ABS.



Operation

Page 43

The following message is shown in the MAXI DOT display.

Error: ABS



The vehicle will only be braked by the normal brake system without the ABS. Seek help from a specialist garage.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 60.

■

If the warning light  » page 38 is displayed simultaneously with the ABS warning light ,  do not continue your journey! Seek help from a specialist garage.

■

A fault to the ABS system or the braking system can increase the vehicle's braking distance – there is a risk of accident.



The rear fog light

Read and observe



The warning light  comes on when the rear fog lights are operating » page 59.



Bulb failure

Read and observe



The warning light  comes on if a bulb is faulty:

within a few seconds of the ignition being switched on;

›

when a light with a defective bulb is switched on.

›

The following message may be shown in the MAXI DOT display, for example.



INFORMATION Check front right low beam!

Note

The rear side lights and the licence plate lighting have several light bulbs. The indicator light  only lights up if all light bulbs of the licence plate lighting or the parking light (in one rear light) are defective. For this reason, regular check that these light bulbs are working correctly.

on page 37 first.

 Exhaust inspection system

Read and observe on page 37 first.



If the warning light  lights up, there is a fault in the exhaust inspection system. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.



Glow plug system (diesel engine)

Read and observe on page 37 first.



The warning light  comes on after the ignition has been switched on. The engine can be started immediately after the pre-glow warning light goes out.

There is a fault in the glow plug system if the warning light  does not come on at all or lights up continuously.

If the warning light  begins to flash while driving, a fault exists in the engine control. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.



EPC fault light (petrol engine)

Read and observe on page 37 first.



If the warning light in the engine control unit. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.



Diesel particulate filter (diesel engine)

Read and observe on page 37 first.



The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a regular basis.

The  warning light comes on if soot has accumulated in the filter.

comes on or begins to flash while driving, a fault exists





Instruments and Indicator Lights

Page 44

In order to clean the filter, and where traffic conditions permit » , the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1,800 - 2,500 rpm for at least 15 minutes or until the warning light goes out with the 4th or 5th gear engaged (automatic gearbox: position S).

The  warning light only goes out once the diesel particulate filter has been successfully cleaned.

If the filter is not properly cleaned, the warning light  does not go out and the warning light  begins to flash.

The following message is shown in the MAXI DOT display.

Diesel particulate filter: Log book!



The engine control unit allows the vehicle to run in emergency mode. After switching the ignition off and on again the indicator light, the indicator light also lights up.

Seek help from a specialist garage.

WARNING

■

The diesel particulate filter reaches very high temperatures - there is a fire hazard and serious injury could be caused. Therefore, never stop the vehicle at places where the underside of your vehicle can come into contact with flammable materials such as dry grass, undergrowth, leaves, spilled fuel or such like.

■

Always adjust your speed to suit weather, road, region and traffic conditions. The recommendations indicated by the warning light must not tempt you to disregard the national regulations for road traffic.

CAUTION

As long as the warning light  lights up, one must take into account an increased fuel consumption and in certain circumstances a power reduction of the engine.

Note

■

We recommend avoiding regularly driving short distances to assist the com-

bustion process of the soot particles in the filter.

■

Using diesel fuel with an increased sulphur content can considerably reduce

the service life of the filter. A ŠKODA Service Partner will be able to tell you which countries use diesel fuel with a high sulphur content.

■

If the engine is turned off during the filter cleaning process or shortly after-

wards, the cooling fan may turn on automatically for a few minutes.

 Fuel reserve

Read and observe on page 37 first.



The indicator light  will come on if the fuel level is less than 7 litres. An audible signal sounds as a warning signal. The following message is shown in the MAXI DOT display.



Please refuel. Range: ... km

Note

The text in the MAXI DOT display only goes out after the vehicle has been refuelled and driven a short distance.





Airbag system

Read and observe



If the warning light  lights up, there is a fault in the airbag system. The following message is shown in the MAXI DOT display.



Error: Airbag

The operational capability of the airbag system is monitored electronically, even if one of the airbags is switched off.

If a front, side or head airbag or belt tensioner has been switched off using the vehicle system tester:

The  warning light comes on for around 4 seconds after the ignition is

›

switched on and then flashes for approximately another 12 seconds at 2 second intervals.

The following message is shown in the MAXI DOT display.



Airbag/belt tensioner deactivated.

If the front passenger's front airbag was switched off using the key-operated switch on the side of the dash panel on the passenger side:

The  warning light comes on for around 4 seconds after the ignition has

›

been switched on. switching off the airbag is indicated in the middle of the dash panel by the

›

lighting up of the yellow indicator light in display

» page 19.



on page 37 first.

   



Operation

Page 45

WARNING

When a fault in the airbag system occurs, there is a risk of the system not being triggered in the event of an accident. Therefore, this must be checked immediately by a specialized company.



Tyre pressure

Read and observe on page 37 first.



The warning light  lights up, if there is a substantial drop in inflation pressure in one of the tyres. Check and adjust the pressure in all tyres.

If the indicator light  flashes, there is a fault in the tyre pressure monitoring system. Stop the car, turn the ignition off and on again.

If the warning light  flashes again after re-starting the engine, then the help of a professional service provider must be sought.

Further information » page 154, Tyre pressure monitor.

WARNING

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning lights system » page 60.

Note

If the battery has been disconnected, the warning light  illuminates after the ignition is switched on. The warning light should go out after driving a short distance.



Windscreen washer fluid level

Read and observe on page 37 first.



If the windscreen washer fluid level is too low, the warning light  comes on. The following message is shown in the MAXI DOT display.

Top up wash fluid!



Top up with liquid » page 142.

 Traction control (TCS) switched off

Read and observe on page 37 first.



The ASR is switched off by pressing the button » page 117 and the warning light  illuminates.

The following message is shown in the MAXI DOT display.



Traction control (ASR) deactivated.

 

Turn signal system

Read and observe on page 37 first.



Either the left  or right  warning light flashes depending on the position of the turn signal lever.

If a turn signal light fails, the warning light flashes at twice its normal rate. Switching off the hazard warning light system is switched on will cause all of

the turn signal lights as well as both warning lights to flash. Further information » page 58, Turn signal and main beam lights.



Low beam

Read and observe on page 37 first.



The warning light  comes on when low beam is selected » page 56.



Fog lights

Read and observe on page 37 first.



The warning light  comes on when the fog lights are operating » page 58.

 Cruise control system

Read and observe on page 37 first.



The warning light  comes on when the cruise control is operating » page 118.

Instruments and Indicator Lights

Page 46

 Selector lever lock

Read and observe on page 37 first.



If the warning light  lights up, operate the brake pedal. This is necessary to be able to move the selector lever from position P or N » page 108.



Main beam

Read and observe on page 37 first.



The warning light  comes on when the main beam or headlight flasher are selected » page 58.

Unlocking and locking

Introduction



This chapter contains information on the following subjects: Vehicle key 44

Replacing the battery in the remote control key 45 Child safety lock 46 Opening/closing a door 46 Locking/unlocking the vehicle without central locking 47 Emergency locking of the doors 47

Vehicle key

Fig. 25 Key: without/with remote control

Two keys are provided with the vehicle. Depending on the equipment, your vehicle can be equipped with keys without radio remote control » Fig. 25 -  or with radio remote control» Fig. 25 - .



Operation

Page 47

WARNING

■

Never leave the key in the vehicle when you exit the vehicle. Unauthorized persons, such as children, for example, could lock the car, turn on the ignition or start the engine - there is a danger of injury and accidents!

■

When leaving the vehicle, never leave persons who are not completely independent, such as children, unattended in the vehicle. The children might, for example, release the handbrake or take the vehicle out of gear. The vehicle could then start to move – risk of injury and accidents! These individuals might also not be able to leave the vehicle on their own or to help themselves. Can be fatal at very high or very low temperatures!

Replacing the battery in the remote control key

CAUTION

■

Each key contains electronic components; therefore it must be protected

against moisture and severe shocks.

■

Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,

etc.) have a negative effect on the functionality of the locking cylinder and ignition lock.

■

The operation of the remote control may temporarily be affected by interfer-

ence from transmitters close to the car and which operate in the same frequency range (e.g. mobile phone, TV transmitter).

■

The battery must be replaced if the central locking does react to the remote

control at less than around 3 metres away » page 45.

Note

■

When leaving the vehicle, always check if it is locked.

■

If you lose a key, please contact a specialist garage, who will be able to pro-

vide you with a new one.

Fig. 26 Remote control key: Remove cover/remove battery

Each remote control key contains a battery located under the cover

» Fig. 26. The battery needs replacing if red indicator light » Fig. 25 on

page 44 -  does not go on when you press a button on the remote control

key. We recommend having the key batteries replaced by a specialist garage. However, if you would like to replace the discharged battery yourself proceed as follows.

Flip out the key.

›

Press off the battery cover with your thumb or using a flat screwdriver in the

›

region of arrows 1 » Fig. 26. Remove the discharged battery from the key by pressing the battery down-

›

wards in the region of arrow 2. Insert the new battery. Ensure that the “+” symbol on the battery is facing

›

upwards. The correct polarity is shown on the battery cover. Place the battery cover on the key and press it down until it clicks into place.

›

CAUTION

■

Pay attention to the correct polarity when changing the battery.

■

The replacement battery must have the same specification as the original

battery.

For the sake of the environment

Dispose of the used battery in accordance with national legal provisions.

Unlocking and locking



Page 48

Note

■

The system has to be synchronised, if the vehicle cannot be unlocked or

locked with the remote control key after replacing the battery » page 51.

■

If a key has an affixed decorative cover, this will be destroyed when the bat-

tery is replaced. A replacement cover can be purchased from a ŠKODA Partner.

Child safety lock

Fig. 27

Child safety lock: Left rear door

The child safety lock prevents the corresponding rear door from being opened from the inside. The door can only be opened from the outside.

You can switch the child safety lock on and off using the vehicle key.

Switching on

Turn the slot of the safety lock in the direction of the arrow » Fig. 27 (the

›

other way around on the right-hand door).

Switching off

Turn the slot of the safety lock in the opposite direction to the ar-

›

row » Fig. 27 (the other way around on the right-hand door).

Opening/closing a door

Fig. 28 Door handle/door opening lever:

Opening from the outside

Unlock the vehicle and pull the door handleA » Fig. 28 on the door you wish

›

to open.

Opening from the inside

Pull on door opening lever B on the door you wish to open.

›

By the first pull on the opening lever, the door is unlocked. By the second pull on the opening lever, the door is opened.

Closing from the inside

Grasp pull handle C and close the door.

›

WARNING

■

Make sure that the door has closed correctly as it can open suddenly

while the vehicle is being driven – there is a risk of death.

■

Only open and close the door when there is no one in the opening/closing

sweep – there is a risk of injury.

■

An opened door can close spontaneously if there is a strong wind or the

vehicle is on a slope – there is a risk of injury.

■

Never drive with the doors open - there is a risk of death!

Operation

Page 49

Locking/unlocking the vehicle without central locking

Emergency locking of the doors

Fig. 30

Rear door: Emergency locking of the door

Fig. 29 Securing knob in the front door/rear door

The locking knob » Fig. 29 will move upwards or downwards when you lock or unlock the door.

Unlocking from the outside

Unlock the front door with the key » page 49.

›

Unlocking from the inside

Pull on the door opening lever.

›

Locking from the outside

Lock the front door with the key » page 49.

›

Locking from the inside

Push the locking knob » Fig. 29 down.

›

WARNING

Locked doors prevent unwanted entry into the vehicle from outside, for example at road crossings. They do, however, make it more difficult for rescuers to get into the vehicle in an emergency – risk to life!

Note

■

Lock the opened rear doors and front passenger door by closing them and

pressing the securing knob.

■

It is not possible to lock the opened driver's door using the securing knob.

This prevents against inadvertently locking the key in the vehicle.

An emergency locking mechanism is located on the end face of the doors which have no locking cylinder, it is only visible after the door is opened.

Locking

Remove the cover A » Fig. 30.

›

Insert the key into the opening under the panel and press the stopping lever

›

as far as the stop toward the inside.

Replace the cover.

›

After closing the door, it no longer be opened from the outside. The door can be unlocked from the inside by pulling on the door handle again, and then opened from the outside.

Central locking system



Introduction

This chapter contains information on the following subjects: Individual settings

Safe securing Unlocking the vehicle using the key Locking the vehicle with the key Vehicle locking/unlocking from the inside

When using central locking or unlocking, all doors are locked or unlocked simultaneously. The boot lid is unlocked when opening. It can be opened by pressing the handle above the licence plate » page 53, Opening/closing.

Unlocking and locking

48 48 49 49 49



Page 50

Warning light in the driver's door

After locking the vehicle, the warning light flashes for around 2 seconds in quick succession, afterwards it begins to flash evenly at longer intervals.

If the vehicle is locked and the safe securing system » page 48 is not operating, the warning light in the driver door flashes for about 2 seconds fast, goes out and starts to flash evenly at longer intervals after about 30 seconds.

If the indicator light first flashes fast for about 2 seconds, then lights up for about 30 seconds continuously and then flashes slowly, there is a fault in the central locking system or in the interior monitor and in the towing protection » page 52. Seek help from a specialist garage.

Convenience operation of windows

The windows can be opened and closed when unlocking and locking the vehicle » page 55.

CAUTION

If the safe securing system is activated» page 48, the door opening lever and the central locking buttons do not operate.

Note

■

In the event of an accident in which the airbags are deployed, the locked doors are automatically unlocked in order to enable rescuers to gain access to the vehicle.

■

Upon failure of the central locking system, only the driver's door can be unlocked or locked with the key. The other doors and the boot lid can be manually locked or unlocked.

■

Emergency locking of the door » page 47.

■

Emergency unlocking of the boot lid » page 53.

Individual settings

Read and observe on page 48 first.



Opening a single door

This selection function makes it possible to only unlock the driver's door. The other doors remain locked and are only unlocked when the command is repeated.

Automatic locking and unlocking

All the doors and the boot lid are locked automatically once the car reaches a speed of about 15 km/h.

If the ignition key is withdrawn, the car is then automatically unlocked again. In addition, it is possible for the driver or front passenger to unlock the car by pressing the central locking button  » page 49.

The doors can be unlocked and opened from the inside by pulling on the opening lever of the respective door. By the first pull on the opening lever, the door is unlocked. By the second pull on the opening lever, the door is opened.

Note

Individual settings can be applied in a specialist workshop.

Safe securing

Read and observe on page 48 first.



The central locking system is equipped with a safe securing system. The door locks are blocked automatically if the vehicle is locked from the outside. It is then not possible to open the doors with the door handle, either from the inside or from the outside.

You will be informed that the safe lock system is activated after the vehicle is locked by the CHECK SAFE LOCK message on the instrument cluster display. On vehicles equipped with the MAXI DOT display, the display shows Check

deadlock. Log book!

Switching off

The safe lock can be switched off in one of the following ways.

By locking twice within 2 seconds.

›

By disabling the interior monitoring » page 52, Interior monitor and towing

›

protection.

If the vehicle is locked and the safe lock system is switched off, the door can be unlocked and opened from the inside by pulling on the opening lever of the respective door. By the first pull on the opening lever, the door is unlocked. By the second pull on the opening lever, the door is opened.

Switching on

The safe lock switches on automatically the next time the vehicle is locked and unlocked.

Switch-on display

The warning light flashes for around 2 seconds in quick succession, afterwards it begins to flash evenly at longer intervals.



Operation

Page 51

Switch-off display

The indicator light in the driver door flashes fast for about 2 seconds, goes out and starts to flash regularly at longer intervals after about 30 seconds.

WARNING

If the car is locked from the outside and the safe lock system is switched on, no-one must be in the car, as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emergency – risk to life.

Note

This function is only enabled in certain countries.

Unlocking the vehicle using the key

Fig. 31

Turning the key for unlocking and locking the vehicle

Read and observe on page 48 first.



Turn the key in the locking cylinder of the driver's door in the direction of

›

travel (unlocking position) A » Fig. 31. Pull the door handle and open the door.

›

All the doors (only the driver's door on vehicles with anti-theft alarm system)

›

are unlocked. The boot lid is then unlocked.

›

The switched on interior lights come on over the door contact.

›

The safe securing system is deactivated.

›

The windows open while the key is held in the unlock position.

›

The warning light in the driver door stops flashing if the car is not fitted with

›

an anti-theft alarm system » page 51.

Note

If the vehicle is equipped with an anti-theft alarm system, you must insert the key into the ignition lock and switch the ignition on within 15 seconds after unlocking the door in order to deactivate the anti-theft alarm system. The alarm

is triggered if the ignition is not switched on within 15 seconds.

Locking the vehicle with the key

Read and observe on page 48 first.



Turn the key in the locking cylinder of the driver's door opposite to the direc-

›

tion of travel (locking position) B » Fig. 31 on page 49.

All the doors and the boot lid are locked.

›

The switched on interior lights will switch off over the door contact.

›

The windows close while the key is held in the lock position.

›

The safe securing system is immediately activated.

›

The warning light in the driver door begins flashing.

›

Note

If the driver's door has been opened, the vehicle cannot be locked.

Vehicle locking/unlocking from the inside

Fig. 32

Centre console: Central locking button

Read and observe on page 48 first.



If the vehicle was not locked from the outside, you can also unlock and lock it with the rocker switch » Fig. 32 even if the ignition is not switched on.

Locking all doors and the boot lid

Press  on the button » Fig. 32. The symbol  in the button comes on.

›



Unlocking and locking

Page 52

Unlocking all doors and the boot lid

Press  on the button » Fig. 32. The symbol  in the button is no longer

›

illuminated.

The following applies if your vehicle has been locked using the central locking button.

It is not possible to open the doors or the boot lid from the outside (safety

›

feature, e.g. when stopping at traffic lights etc.).

The doors can be unlocked and opened from the inside by pulling on the

›

opening lever of the respective door. By the first pull on the opening lever,

the door is unlocked. By the second pull on the opening lever, the door is

opened.

If at least one door has been opened, the vehicle cannot be locked.

›

In the event of an accident in which the airbags are deployed, the locked

›

doors are automatically unlocked in order to enable rescuers to gain access

to the vehicle.

WARNING

■

Doors locked from the inside make it difficult for rescuers to get into the

vehicle in an emergency – risk to life!

■

If the safe lock system is switched on » page 48, the door opening lever

and the central locking buttons do not operate.

Remote control

Introduction



This chapter contains information on the following subjects: Unlocking/locking

Synchronization 51

You can use the remote control key to:

unlock and lock the vehicle,

›

unlocking boot lid;

›

open and close the windows » page 55, Window convenience operation.

›

The transmitter with the battery is housed in the handle of the remote control key. The receiver is located in the interior of the vehicle. The operating range of the remote control key is approx. 30 m. But this range of the remote control can be reduced if the batteries are weak.

The key has a fold-open key bit which can be used for unlocking and locking the car manually and also for starting the engine.

If a lost key is replaced or if the receiver unit has been repaired or replaced, the system must be initialised by a specialist garage. Only then can the remote control key be used again.

Note

■

The remote control is automatically deactivated when the ignition is switch-

ed on.

■

The operation of the remote control may temporarily be affected by interference from transmitters close to the car and which operate in the same frequency range (e.g. mobile phone, TV transmitter).

■

The battery must be replaced if the central locking or anti-theft alarm system does react to the remote control at less than 3 metres away » page 45.

■

If the driver door is open, the vehicle cannot be locked using the remote control key.

Unlocking/locking

Fig. 33

Remote control key

Unlocking the vehicle

Press button 1 » Fig. 33.

›

Locking the vehicle

Press button 3 » Fig. 33.

›

Deactivating the safe securing system

Press button 3 » Fig. 33 twice within 2 seconds. Further informa-

›

tion » page 47.

Unlocking the boot lid

Press button 2 » Fig. 33. Further information » page 53.

›









Operation

Page 53

Folding out the key bit

Press button 4 » Fig. 33.

›

Folding in the key bit

Press the button 4 » Fig. 33 and fold in the key bit.

›

Unlocking

The turn signal lights flash twice as confirmation that the vehicle has been unlocked. If the vehicle is unlocked using button 1 » Fig. 33 and none of the doors or the tailgate are opened within the next 30 seconds, the vehicle is automatically locked again and the safe securing system or anti-theft alarm system is reactivated. This function is intended to prevent the car being unlocked unintentionally.

In addition, when the car is unlocked, the electrically adjustable seats and exterior mirrors move into the position assigned to this key. The stored setting of driver seat and exterior mirrors is retrieved.

Locking

The turn signal lights flash once to confirm that the vehicle has been correctly locked.

If the doors or the boot lid remain open after the vehicle has been locked, the turn signal lights do not flash until they have been closed.

Note

■

Only operate the remote control when the doors and boot lid are closed and

the vehicle is in your line of sight.

■

A ŠKODA partner can also activate/deactivate the acoustic signals on vehi-

cles with an anti-theft alarm system.

Synchronization

If the vehicle does not unlock when the remote control is pressed, the key may not be synchronised. This can occur when the buttons on the remote control key are pressed several times outside the operating range of the equipment or if the battery in the remote control key has been replaced.

Synchronise the key as follows.

Press any button on the remote control key.

›

Unlock the door with the key within 1 minute of pressing the button.

›

Anti-theft alarm system

 Introduction

This chapter contains information on the following subjects: Operation

Interior monitor and towing protection 52

The anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle.

Note

■

The working life of the alarm siren is 5 years.

■

Before leaving the vehicle, check that all the doors and windows are closed

in order to ensure that the anti-theft alarm system is fully operational.

■

Coding of the radio remote control and the receiver unit precludes the use of

the radio remote control from other vehicles.

Operation

How is the alarm system activated?

The anti-theft alarm system is activated when the vehicle is locked with the radio remote control or the key in the driver's door . It is activated 30 seconds after locking the door.

How is the alarm system deactivated?

The alarm system is deactivated by pressing the  button on the remote control. The anti-theft alarm system is reactivated if the vehicle is not opened within 30 seconds after transmitting the radio signal.

If the vehicle is unlocked by inserting the key into the driver door, the key must be inserted into the ignition lock and the ignition switched on within 15 seconds of unlocking the door to deactivate the alarm system. The alarm is

triggered if the ignition is not switched on within 15 seconds.

When is the alarm triggered?

The following security areas of the locked vehicle are monitored:

bonnet;

›

boot lid;

›

doors;

›

ignition lock;

›

Vehicle inclination » page 52;

›



Unlocking and locking

Page 54

Interior of the vehicle » page 52;

›

A drop in voltage of the on-board power supply;

›

Socket of the factory-fitted towing device.

›

An alarm is immediately triggered if either of the two battery terminals is disconnected while the anti-theft alarm system is activated.

How is the alarm switched off?

The alarm is turned off by pressing the  button on the remote control key or switching the ignition on.

Interior monitor and towing protection

Fig. 34

Button for interior monitor and towing protection

The interior monitor detects movements inside the car and then triggers the alarm.

Switching off

Switch off the ignition.

›

Open the driver door.

›

Press the  » Fig. 34 button in the driver's door.

›

Lock the vehicle within 30 seconds.

›

The interior monitor and the towing protection are switched on again automatically the next time the car is locked.

Note

■

Deactivate the interior monitor and the towing protection if there is a possibility of the alarm being triggered by movements (e.g. by children or animals) within the vehicle interior or if the vehicle has to be transported (e.g. by train or ship) or towed.

■

The opened glasses storage compartment reduces the effectiveness of the interior monitor. To ensure the full functionality of the interior monitor, the glasses storage compartment must always be closed before locking the vehicle.

Luggage compartment lid

 Introduction

This chapter contains information on the following subjects: Opening/closing

Delayed locking of the boot lid 53 Emergency unlocking 53

WARNING

■

Ensure that the lock is properly engaged after closing the boot lid. Otherwise, the lid might open suddenly while the vehicle is moving, even if the lid was locked – risk of accident!

■

Never drive with the luggage compartment lid open or ajar, as otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning!

■

Do not press on the rear window when closing the tailgate, as otherwise this could crack – there is a risk of injury.

Note

■

After closing the boot lid, it is automatically locked within 1 second and the

anti-theft alarm system is activated. This applies only if the vehicle was

locked before closing the boot lid.

■

The function of the handle above the licence plate is deactivated when start-

ing off or at a speed of 5 km/hour or more for vehicles with central locking. The function of the handle is activated again when the vehicle has stopped and a door is opened.

Operation

Page 55

Opening/closing

Fig. 35 Unlock the boot lid/boot lid handle

Read and observe



After unlocking the vehicle, you can open the lid by pushing the handle located above the licence plate.

Opening the boot lid for vehicles without central locking

Press the  symbol button » Fig. 35 -  in the driver's door and open the

›

boot lid in the direction of the arrow » Fig. 35 - .

Opening the boot lid for vehicles with central locking

Press the handle and open the tailgate in the direction of the arrow » Fig. 35

›

- .

Closing

Pull down the tailgate and close it with a gentle swing.

›

A handle which makes the closing easier is located on the inner panelling of the boot lid.

on page 52 first.

Delayed locking of the boot lid

Read and observe



If the boot lid is unlocked with the symbol button  on the remote control key, then the door is automatically locked after closing.

The period after which the boot lid is locked automatically can be extended by a specialist garage.

After activation of delayed locking, the boot lid can be opened again after closing within a limited period.

on page 52 first.

Delayed locking can be deactivated by a specialist garage at any time.

CAUTION

There is a risk of unwanted entry into the vehicle before the boot lid is locked automatically. We therefore recommend locking the vehicle with the symbol button  on the remote control key.

Emergency unlocking

Fig. 36

Emergency unlocking of the boot lid

Read and observe on page 52 first.



The boot lid can be unlocked manually if there is a fault in the central locking system.

Unlocking

Fold the rear seat backrest forward » page 67.

›

Insert a screwdriver or similar tool into the opening in the trim in the direc-

›

tion of the arrow 1 » Fig. 36 as far as the stop. Unlock the lock 3 under the trim in the direction of arrow 2.

›

Open the tailgate.

›

Electrical power windows



Introduction

This chapter contains information on the following subjects: Opening/closing the windows

Power window force limiter 55 Window convenience operation 55 Operational faults 55



Unlocking and locking

Page 56

WARNING

■

If the vehicle is locked from the outside, do not leave anybody in the vehicle as it is not possible to open the windows from the inside in the event of an emergency.

■

The system is fitted with a force limiter » page 55. If there is an obstacle, the closing process is stopped and the window goes down by several centimetres. The windows should nevertheless be closed carefully – risk of injury.

■

Deactivating the electrically operated power windows in the rear doors is recommended (safety push button) S when children are being transported in the rear seats » Fig. 37 on page 54.

■

When closing the windows, proceed with caution so as to avoid causing crushing injuries - risk of injury!

CAUTION

■

Keep the windows clean to ensure the correct functionality of the electric

windows.

■

If the windows are frozen, first of all remove the ice » page 133, Windows

and exterior mirrors. Only then can the electrical power windows be operated,

as otherwise the window seal and the electrical power window mechanism could be damaged.

■

In the winter, ice on the window may cause greater resistance as the win-

dow is closed. The window will stop and open again by several centimetres.

■

Make sure that the windows are closed whenever you leave the locked vehi-

cle.

For the sake of the environment

At high speeds, you should keep the windows closed to prevent unnecessarily high fuel consumption.

Note

■

After switching the ignition off, it is still possible to open or close the win-

dows for approx. 10 minutes. After the driver's or front passenger's door has been opened, the windows can only be operated by using button A » Fig. 37 on page 54.

■

When driving always use the existing heating, air conditioning and ventila-

tion system for ventilating the interior of the vehicle. If the windows are opened, dust as well as other dirt can get into the vehicle and in addition the wind noise is more at certain speeds.

Opening/closing the windows

Fig. 37 Buttons on the driver's door/in the rear doors

Read and observe



Power window buttons » Fig. 37.

Button for electrical power window of the driver's door

Button for electrical power window of the front passenger door

Button for electrical power window of the rear right door

Button for electrical power window of the rear left door

Safety pushbutton

The electrical power windows can only be operated when the ignition is switched on.

Opening

The window is opened by pressing lightly on the corresponding button. The

›

opening process stops when one releases the button.

The window will also open fully automatically if you briefly press the button as far as the stop. Renewed pressing of the button causes the window to stop immediately.

Closing

The window is closed by pulling lightly on the corresponding upper edge of

›

the button. The closing process stops when one releases the button.

The window will also close fully automatically if you briefly pull the button as far as the stop. Renewed pulling of the button causes the window to stop immediately.

and on page 54 first.



Operation

Page 57

Safety pushbutton

The buttons for power windows in the rear doors can be deactivated by pressing the safety switch S » Fig. 37. The buttons for the electrical power windows in rear doors are activated again by pressing the safety pushbutton again.

If the buttons for the rear doors are deactivated, the warning light  in the safety switch S lights up.

Note

The window lift mechanism is equipped with protection against overheating. Repeated opening and closing of the window can cause this mechanism to overheat. If this happens, it will not be possible to operate the window for a short time. You will be able to operate the window again as soon as the overheating protection has cooled down.

Power window force limiter

Read and observe and on page 54 first.



The electrical power windows are fitted with a force limiter. It reduces the risk of bruises or injuries when closing the windows.

If there is an obstacle, the closing process is stopped and the window goes down by several centimetres.

If the obstacle prevents the window from being closed during the next 10 seconds, the closing process is interrupted once again and the window goes down by several centimetres.

If you attempt to close the window again within 10 seconds of the window being moved down for the second time, even though the obstacle was not yet been removed, the closing process is only stopped. During this time it is not possible to automatically close the window. The force limiter is still switched on.

The force limiter is only switched off if you attempt to close the window again within the next 10 seconds - the window will now close with full force!

If you wait longer than 10 seconds, the force limiter is switched on again.

Window convenience operation

Read and observe and on page 54 first.



The convenience operation of the windows offers the possibility of opening or closing all the windows at once.

Convenience operation can take place in one of the following ways.

Opening

Press the  symbol button on the remote control key and hold.

›

Hold the key in unlock position in the driver's door lock.

›

Hold button A » Fig. 37 on page 54 in the opening position.

›

Closing

Press the  symbol button on the remote control key and hold.

›

Hold the key in the lock position in the driver's door lock.

›

Hold button A » Fig. 37 on page 54 in the closing position.

›

The movement of the window is stopped immediately when the key or the respective button is released.

Operational faults

Read and observe



Electrical power windows do not operate

If the battery has been disconnected and then reconnected while the window was opened, the electrical power windows will not operate. The system must be activated. Proceed as follows to re-establish the function.

Switch on the ignition.

›

Pull the top edge of the button in the driver's door and close the window.

›

Release the button.

›

Pull the relevant button upwards again for another approximately 3 seconds

›

and hold.

Operation in winter

In the winter, ice accumulating on the surface of the window may cause there to be more resistance when closing the window. The window will stop and move back several centimetres.

It is necessary to deactivate the force limiter to close the window » page 55.

and on page 54 first.

Unlocking and locking

Page 58

Lights and visibility

Parking and low beam lights

Lights

Introduction



This chapter contains information on the following subjects: Parking and low beam lights 56

Headlight beam adjustment 57 Daylight running lights (DAY LIGHT) 57 Turn signal and main beam lights 58 Halogen projector headlights with cornering light function 58 Fog lights 58 Foglights with the CORNER function 59 Rear fog light 59 Tourist lights 59 Hazard warning light system 60 Parking lights 60

Unless otherwise stated, the lights only work when the ignition is on.

The layout of the controls differs in part from that shown in » Fig. 38 on page 56 on right-hand drive vehicles. The symbols which mark the positions

of the controls are identical.

WARNING

■

Never drive with only the side lights on! The side lights are not bright enough to light up the road sufficiently in front of you or to be seen by other oncoming traffic. Therefore always switch on the low beam when it is dark or if visibility is poor.

■

The activation of the lights should only be undertaken in accordance with national legal requirements.

■

The driver is always responsible for the correct settings and use of the lights.

Fig. 38

Dash panel: Light switch

Read and observe on page 56 first.



Light switch positions » Fig. 38.

Switch on the parking light or parking lights on both sides » page 60



Switch on low beam



Switching off lights (except daytime running lights)



Switching on the front fog lights » page 58



Switching on the rear fog light » page 59



Note

■

An audible warning signal will sound if the light switch is in the  or  position, the ignition key is removed and the driver's door is opened. The audible warning signal is switched off by means of the door contact when the driver's door is closed (ignition off), however, the side lights remain on to illuminate the parked vehicle if necessary.

■

Always turn the light switch to the 0 position if you are leaving the vehicle and don't want to use the parking light.

Note

The headlights may mist up temporarily. When the driving lights are switched on, the light outlet areas are free from condensation after a short time, although the headlight lenses may still be misted up around the edge. This mist has no influence on the life of the lighting system.

Operation

Page 59

Headlight beam adjustment

Fig. 39

Dash panel: Lights and visibility

Read and observe on page 56 first.



Turning the rotary switch » Fig. 39 from position  to  gradually adjusts the headlight beam thereby shortening the beam of light.

The positions of the rotary switch correspond approximately to the following car load.

Front seats occupied, boot empty.



All seats occupied, boot empty.



All seats occupied, boot loaded.



Driver seat occupied, boot loaded.



WARNING

Always adjust the headlight beam to satisfy the following conditions.

■

The vehicle does not dazzle other road users, especially oncoming vehi-

cles.

■

The beam range is sufficient for safe driving.

Note

We recommend you adjust the headlight beam when the low beam is switched on.

Activating/deactivating the daytime running lights function

Activate and deactivate the daytime running lights by fitting/removing the

›

fuse with the appropriate ampere rating for daytime running lights » page 168, Fuses in the dash panel.

Deactivating on vehicles with the START-STOP system

Switch off the ignition.

›

At the same time, pull the turn signal light stalk » Fig. 40 on page 58 to-

›

wards the steering wheel, push it downwards, and hold it in this position. Switch on the ignition - wait until the left-turn signal light flashes 4x.

›

Switch off the ignition - an audible signal sounds which confirms the deacti-

›

vation of the daylight driving lights. Release the turn signal stalk.

›

Activating on vehicles with the START-STOP system

Switch off the ignition.

›

At the same time, pull the turn signal light stalk » Fig. 40 on page 58 to-

›

wards the steering wheel, push it upwards, and hold it in this position. Switch on the ignition - wait until the right-turn signal light flashes 4x.

›

Switch off the ignition - an audible signal sounds which confirms the activa-

›

tion of the daylight driving lights. Release the turn signal stalk.

›

On vehicles with separate lights for daylight driving lights in the fog lights or in the front bumper, the parking lights and the licence plate light do not come on when activating the function daylight driving lights (neither front nor rear).

If the vehicle is not equipped with separate lights for daylight driving lights, the combination of the low beam, the parking lights (front and rear) including the licence plate light is used as daylight driving lights.

Note

The daytime driving lights also serve as parking lights on vehicles with separate lights for daylight driving lights (in the bumper below the main headlights).

Daylight running lights (DAY LIGHT)

Read and observe



Switching on daytime running lights

Turn the light switch to position 0 » Fig. 38 on page 56.

›

on page 56 first.

Lights and visibility

Page 60

Turn signal and main beam lights

Fig. 40

Operating lever: Turn signal and main beam operation

Read and observe on page 56 first.



The parking light is controlled with the control stalk » page 60.

Control stalk positions » Fig. 40.

Switch on right turn signal

Switch on left turn signal

Switch on high beam (spring-loaded position)

Switch off main beam and headlamp flasher (spring-loaded position)

When the left or right turn signal is on, the  or  warning light flashes in the instrument cluster.

When the high beam or headlight flasher is on, the  warning light lights up in the instrument cluster.

Turn signal for changing lanes - to flash only briefly, move the stalk up or down to the pressure point only and hold it in this position.

Convenience turn signal

If you wish to flash three times only, briefly push the stalk to the upper or lower pressure point and release again.

WARNING

Only turn on the main beam or the headlight flasher if other road users will not be dazzled.

Note

■

The main beam can only be switched on when the low beam lights are on.

■

The headlight flasher can be operated even if the ignition is switched off.

■

The turn signal system only operates when the ignition is switched on.







■

The turn signal is automatically cancelled after negotiating a curve.

■

The warning light flashes at twice its normal rate if a bulb for the turn signal light fails.

Halogen projector headlights with cornering light function

Read and observe on page 56 first.



For a better cornering illumination, the halogen projector headlights with cornering light function are set in the optimal position in line with the vehicle speed and the steering angle.

WARNING

If the halogen projector headlights with cornering light function are faulty,

the headlights are automatically lowered to the emergency position, which

prevents a possible dazzling of oncoming traffic. Thus the illuminated

length of the road is shortened. Drive carefully and visit a specialist garage

as soon as possible.

Fog lights

Fig. 41

Dash panel: Light switch

Read and observe on page 56 first.



Switching on/off

First turn the light switch » Fig. 41 to position  or .

›

Pull the light switch to position 1.

›

The rear fog light is switched off in the reverse sequence.

The warning light  lights up in the instrument cluster when the fog lights are switched on » page 37.

Operation

Page 61

Foglights with the CORNER function

Read and observe on page 56 first.



The CORNER function lights the front fog lamp on the relevant side of the vehicle to illuminate the area around the vehicle when turning, parking, etc.

The CORNER function is switched on automatically if the following conditions are met.

The turn signal is switched on or the front wheels are turned sharply to the

›

right or left1). The engine is running.

›

The vehicle is stopped or moves at a speed of no more than 40 km/h.

›

The low beam is switched on.

›

The daytime running lights are not switched on.

›

The fog lights are not switched on.

›

Reverse gear is not engaged.

›

Rear fog light

Read and observe



Switching on/off

First turn the light switch » Fig. 41 on page 58 to position  or .

›

Pull the light switch to position 2.

›

The rear fog light is switched off in the reverse sequence.

If the vehicle is not fitted with fog lights » page 58, the rear fog light is switched on by turning the light switch to the position  or  and is pulled out directly to the position 2. This switch can only be pulled into one position.

The warning light  lights up in the instrument cluster when the rear fog light is switched on » page 37.

Only the rear fog light on the trailer lights up if the vehicle has a factory-fitted towing device or a towing device from ŠKODA original accessories and it is driven with a trailer.

on page 56 first.

Tourist lights

Read and observe on page 56 first.



Halogen projector headlights with cornering light function

This mode makes it possible to drive in countries with opposing traffic system (driving on the left/right) without dazzling the oncoming vehicles. When the mode “tourist light” is active, the side to side swivel of the headlights is deactivated.

Activating tourist light

Before activating the tourist light, the following conditions must be met. Ignition switched off, light switched off (light switch in position 0), control dial

for headlamp beam adjustment in the  position, no gear engaged or selector lever in the N position (automatic gearbox), tourist light deactivated.

Switch on the ignition.

›

Within 10 seconds of the ignition being switched on:

Turn the light switch to the  position » page 56, Parking and low beam

›

lights. Engage reverse gear (manual gearbox) or move the selector lever to the R

›

position (automatic gearbox), Turn the headlamp beam adjustment dial from  to  » page 57.

›

Deactivating tourist light

Before deactivating the tourist light, the following conditions must be met. Ignition switched off, light switched off (light switch in position 0), control dial

for headlamp beam adjustment in the  position, no gear engaged or selector lever in the N position (automatic gearbox), tourist light activated.

Switch on the ignition.

›

Within 10 seconds of the ignition being switched on:

Turn the light switch to the  position » page 56, Parking and low beam

›

lights. Engage reverse gear (manual gearbox) or move the selector lever to the R

›

position (automatic gearbox), Turn the headlamp beam adjustment dial from  to  » page 57.

›



If both switch on versions are conflicting, for example if the steering wheel is turned to the left and the right turn signal light is switched on, the turn signal light has the higher priority.

Lights and visibility

Page 62

Further information » page 115, Headlights.

Note

When the “tourist light” mode is active, the warning light  flashes for 10 seconds each time the ignition is switched on.

Hazard warning light system

Fig. 42

Dash panel: Button for hazard warning light system

Read and observe on page 56 first.



Press the  » Fig. 42 button.

›

All the turn signal lights on the vehicle flash at the same time when the hazard warning light system is switched on. The warning light for the turn signals and the warning light in the button also flash at the same time. The hazard warning light system can also be operated if the ignition is switched off.

The hazard warning light system will switch on automatically if one of the airbags is deployed.

CAUTION

Switch on the hazard warning light system if, for example, the following occurs.

■

You encounter a traffic jam.

■

The vehicle has broken down.

Parking lights

Read and observe on page 56 first.



Switching on the parking light

Switch off the ignition.

›



Pull the turn signal stalk » Fig. 40 on page 58 upwards or downwards - the

›

side light on the right or left side of the vehicle is switched on.

Switching on the side lights on both sides

Turn the light switch » Fig. 38 on page 56 to the  position and lock the ve-

›

hicle.

Note

■

The parking light  can only be activated if the ignition is switched off.

■

If the right or left turn signal light has been switched on and the ignition is switched off, the parking light is not automatically switched on.



Interior lights

Introduction



This chapter contains information on the following subjects: Interior lighting - version 1 60

Interior lighting - version 2 Illuminated storage compartment on the passenger side Luggage compartment light

Interior lighting - version 1

Fig. 43

Interior lighting – version 1

Positions of sliding switch A » Fig. 43.

Switch on



Switch off (middle position)



Control with the door contact switch



The reading lights can be turned on or off by pressing switch B » Fig. 43.

61 61 61



Operation

Page 63

If control of the lights by the door contact switch is enabled (switch

» Fig. 43 is in the  position), the light will come on when one of the fol-

lowing occurs.

The vehicle is unlocked.

›

One of the doors is opened.

›

The ignition key is removed.

›

If control of the lights by the door contact switch is enabled (switch A» Fig. 43 in the  position), the light will go off when one of the following occurs.

The vehicle is locked.

›

The ignition is switched on.

›

About 30 seconds after all the doors have been closed.

›

If a door remains open, or if switch A » Fig. 43is in the  position, the interior light goes out after 10 minutes to prevent the vehicle battery from discharging.

Interior lighting - version 2

Fig. 44

Interior lighting – version 2

Luggage compartment light

The light comes on automatically when the boot lid is opened. If the tailgate remains open for more than 10 minutes, the luggage compartment light switches off automatically.

Visibility

 Introduction

This chapter contains information on the following subjects: Rear window heater

Sun visors 62 sunshade 62

Rear window heater

Fig. 45

Button for rear window heater

Slide switch positions » Fig. 44.

Switch on



Switch off



Control by the door contact switch (middle position)



The same principles apply for interior lighting version 2 as for » page 60, Interior lighting - version 1.

Illuminated storage compartment on the passenger side

When opening the flap of the storage compartment on the front passenger

›

side the lighting in the storage compartment comes on. The light switches on automatically when the parking light is switched on

›

and goes out when the flap is closed.

The rear window heater is switched on or off by pressing the  but-

›

ton » Fig. 45, the warning light in the switch comes on or goes out.

The rear window heater can only be switched on when the engine is running. The rear window heater switches off automatically after approximately 7 mi-

nutes.

For the sake of the environment

The heating should be switched off as soon as the window is de-iced or free from mist. The reduced current consumption will have a favourable effect on fuel economy » page 113, Saving electrical energy.

Lights and visibility



Page 64

Note

If the on-board voltage drops, the rear window heater switches off automatically, in order to provide sufficient electrical energy for the engine control » page 151, Automatic load deactivation.

Sun visors

Fig. 46

Sun visor: swivelling out

The sun visor for the driver or front passenger can be pulled out of the fixture and swivelled towards the door in the direction of arrow 1 » Fig. 46.

The vanity mirrors in the sun visors are provided with covers. Push the cover in the direction of the arrow 2.

The purpose of the strap A is to store small, light objects, such as a notepad, etc.

WARNING

sunshade

Fig. 47

Sun screen

The sunshade can be opened or closed manually » Fig. 47.

Please pay attention to the following points if you wish to transport luggage or other items on the roof of your vehicle » page 77, in section Introduc- tion.

WARNING

When operating the sunshade, proceed with caution to avoid causing

crushing injuries – risk of injury!

Windscreen wipers and washers



Introduction

This chapter contains information on the following subjects: Windscreen wiper and washer 63

Headlight cleaning system 64 Replacing the windscreen wiper blades 64 Replacing the rear window wiper blade 64

The windscreen wipers and the windscreen washer system only operate when the ignition is switched on.

The rear window is wiped once automatically if the windscreen wipers are on when reverse gear is selected.

Top up with windscreen wiper fluid » page 142.



Operation

Page 65

WARNING

■

Properly maintained windscreen wiper blades are essential for clear visi-

bility and safe driving » page 64.

■

Do not use the windscreen washer system at low temperatures, without heating the windscreen beforehand. Otherwise the window cleaner could freeze on the windscreen and restrict the view to the front.

■

Replace the windscreen wiper blades once or twice a year for safety reasons. These can be purchased from a ŠKODA Partner.

CAUTION

■

In cold temperatures and during the winter, check before the journey or be-

fore switching on the ignition that the wiper blades are not frozen to the windscreen. If the windscreen wipers are switched on when the blades are frozen to the windscreen, this may damage both the blades and windscreen wiper motor!

■

If the ignition is switched off while the windscreen wipers are switched on,

the windscreen wipers will continue wiping in the same mode after the ignition is turned back on. The windscreen wipers could freeze up in cold temperatures between the time the ignition was turned off and when it was turned back on again.

■

Carefully detach frozen wiper blades from the front or rear window.

■

Remove snow and ice from the windscreen wipers before driving.

■

If the windscreen wipers are handled carelessly, there is a risk of damage to

the windscreen.

Note

■

The windscreen washer nozzles for the windscreen are heated when the en-

gine is running and the outside temperature is less than approx. +10 °C.

■

The content of the windscreen washer fluid reservoir is 3.5 litres. On vehicles

fitted with the headlight cleaning system, the volume is around 5.4 litres.

■

The wiper blades should be cleaned on a regular basis with a windscreen

cleaner to avoid any smears. The wiper blades should be cleaned with a sponge or cloth if they are heavily soiled by insect residues, for example.

Windscreen wiper and washer

Fig. 48

Operating lever: Windscreen wipers and washer settings

Read and observe and on page 63 first.



Control stalk positions » Fig. 48.

Wipers off

Interval windscreen wiping

Slow windscreen wiping

Rapid windscreen wiping

Single windscreen wipe (spring-loaded position)

Automatic wipe/wash for windscreen (spring-loaded position)

Wiping the rear window (the windscreen wiper wipes at regular intervals after a few seconds)

Automatic wipe/wash for the rear window (spring-loaded position)

Switch for setting the desired interval between the individual windscreen wipes (1 Interval windscreen wiping)

Automatic wipe/wash for windscreen

The wash system operates immediately, the windscreen wipers wipe somewhat later.

Releasing the lever will stop the windscreen washer while the wipers continue for another 1 to 3 wiper strokes (depending on the period the windscreen has been sprayed).

Automatic wipe/wash for the rear window

The wash system operates immediately, the wiper wipes somewhat later. Releasing the lever will stop the washer while the wipers continue for another

1 to 3 wiper strokes (depending on the period the window has been sprayed).

The lever will stay in position after releasing it

Lights and visibility

Page 66

Headlight cleaning system

Read and observe and on page 63 first.



The headlights are sprayed briefly if the low beam or main beam are switched on and the windscreen wiper stalk is pulled to position 5 » Fig. 48 on page 63. To clean the headlights, the windshield is also sprayed after every five squirts.

You should remove stubborn dirt (such as insect residues) from the headlight lenses at regular intervals, for example when refuelling. The following guidelines must be observed » page 133, Headlight lenses.

To ensure the proper operation of the cleaning system during the winter, any snow should be removed from the washer nozzle fixtures and ice should be cleared with a de-icing spray.

CAUTION

Never remove the nozzles from the headlight cleaning system by hand – there is risk of damage.

Windshield wiper blades in proper condition are essential to obtain good visibility. Wiper blades should not be allowed to become dirtied by dust, insect remains and preserving wax.

Juddering or smearing of the wiper blades could then be due to wax residues left on the windshield by vehicle washing in automatic vehicle wash systems. It is therefore important to clean and degrease the lips of the windshield wiper blades after every pass through the automatic vehicle wash system.

Replacing the rear window wiper blade

Fig. 50

Rear window wiper blade

Replacing the windscreen wiper blades

Fig. 49

Windscreen wiper blade

Read and observe and on page 63 first.



Removing the wiper blade

Lift the windscreen wiper arm away from the windscreen.

›

Press the locking button 1 » Fig. 49 and remove the wiper blade in the di-

›

rection of arrow 2.

Fitting the wiper blade

Push the wiper blade in until it latches on the stop.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arms back to the windscreen.

›

Operation

Read and observe and on page 63 first.



Removing the wiper blade

Raise the wiper arm away from the window » Fig. 50.

›

Tilt the wiper blade to the stop in the direction of the wiper arm.

›

Hold the upper part of the wiper arm and unlock the securing mechanism 1.

›

Remove the wiper blade in the direction of the arrow 2.

›

Fitting the wiper blade

Push the wiper blade in until it latches on the stop.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arm back to the windscreen.

›

Rear window



Introduction

This chapter contains information on the following subjects: Manually dimmed rear-view mirror 65

Exterior mirrors



Page 67

WARNING

■

Make sure that the mirror is not covered by ice, snow, condensation or other objects.

■

Convex (curved outward) or aspheric exterior mirrors increase the field of vision. They do, however, make objects appear smaller in the mirror. These mirrors are therefore only of limited use for estimating distances to the following vehicles.

■

Whenever possible use the interior mirror for estimating the distances to the following vehicles.

Manually dimmed rear-view mirror

Read and observe on page 65 first.



Basic setting

Adjust the lever at the lower edge of the mirror towards the windshield.

›

Dimming mirror

Pull the lever on the lower edge of the mirror away from the windscreen.

›

Exterior mirrors

Fig. 51

Inner part of door: Knob for the mirrors

Read and observe on page 65 first.



The knob can be moved into the following positions.

Adjust the left mirror



Adjust the right mirror



Switch off mirror control



Mirror heater



The mirror can be adjusted to the desired position by moving the knob in the direction of the arrow » Fig. 51.

The movement of the mirror surface follows the movement of the rotary knob.

Folding in the exterior mirrors

The whole exterior mirror can be manually folded towards the side windows. Restore it to its original position, it should be folded back from the side window until it audibly clicks into place.

Note

■

The exterior mirror heater only operates when the engine is running.

■

Do not touch the surface of the exterior mirrors if the exterior mirror heater

is switched on.

■

If the power setting function fails at any time, the exterior mirrors can be set

by hand by pressing on the edge of the mirror surface.

■

Contact a specialist garage if there is a fault with the power setting function

for the exterior mirrors.

Lights and visibility

Page 68

Seats and stowing

Adjusting the front seats

Front seats

Introduction



This chapter contains information on the following subjects: Adjusting the front seats 66

Front seat heating 66

The driver's seat should be adjusted in such a way that the pedals can be fully pressed to the floor with slightly bent legs.

The seat backrest on the driver's seat should be adjusted in such a way that the upper point of the steering wheel can be easily reached with slightly bent arms.

Correct adjustment of the seats is particularly important for the following reasons.

Reaching the controls safely and quickly.

›

A relaxed and fatigue-free body position.

›

Achieving the maximum protection offered by the seat belts and the airbag

›

system.

WARNING

■

Only adjust the driver's seat when the vehicle is stationary – risk of acci-

dent!

■

Caution when adjusting the seat! You may suffer injuries or bruises as a

result of adjusting the seat without paying proper attention.

■

Never carry more people than the number of seats in the vehicle.

■

Do not carry any objects on the front passenger seat except objects de-

signed for this purpose (e.g. child seat) – risk of accident!

Note

After a certain time, play can develop within the adjustment mechanism of the backrest angle.

Fig. 52

Control elements at the seat

Read and observe on page 66 first.



Adjusting a seat in a forward/back direction

Pull lever

›

Release the lever 1 and push the seat until the lock clicks into place.

›

Adjusting height of seat

To lift the seat, pull or pump lever 2 » Fig. 52 upwards.

›

To lower the seat, push or pump the lever 2 downwards.

›

Adjusting the angle of the seat backrest

To adjust the angle of the backrest, relieve any pressure from the seat back-

›

rest (do not lean on it) and turn handwheel 3 » Fig. 52.

» Fig. 52 up and push the seat into the desired position.

Front seat heating

Fig. 53

Rocker switch for front seat heating

Operation

Read and observe on page 66 first.



The seat backrests and seats can be heated electrically.



Page 69

Switch the front seat heating to 25 % or 100 % power by pressing rocker

›

switch at position 1 or 2 » Fig. 53. To switch off the heating shift the rocker switch into the horizontal position.

›

WARNING

If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating. This can lead to burns on the back, the posterior and the legs which are difficult to heal. If the seat heating is used, we recommend to make regular breaks in your journey when driving long distances, so that the body can recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.

CAUTION

■

Do not kneel on the seats or otherwise apply pressure at specific points to

avoid damaging the heating elements for the seat heaters.

■

Do not turn on the seat heater if seats are not occupied.

■

Do not switch on the seat heating if the seats have objects attached to or

placed on them, for example a child seat, a bag, etc. A fault of the heating elements in the seat heating can occur.

■

If additional seat covers or protective covers are attached to the seats, do

not turn on the seat heater - there is a risk of damaging the seat covers and seat heating.

■

Do not clean the seats using moisture » page 136, Seat covers.

Note

■

The seat heating should only be switched on when the engine is running.

This has a significant effect of saving on the battery capacity.

■

If the on-board voltage drops, the seat heating is switched off automatically,

in order to provide sufficient electrical energy for the engine control » page 151, Automatic load deactivation.

Unlocking and removing seats 68 Adjusting seats in crosswise direction 69 Folding the rear seats into the starting position 69

Setting theSetting the seats in the longitudinal direction

Fig. 54 Releasing at the front/rear

Pull lever A » Fig. 54 up in the direction of arrow 1 or pull on the release

›

loop in direction of arrow 2 and move the seat into the desired position 3.

Setting theinclination of the seat backrest

Fig. 55

Adjusting the seat backrest

Rear seats

Introduction



This chapter contains information on the following subjects: Setting theSetting the seats in the longitudinal direction

Setting theinclination of the seat backrest Fold downseat backrest and seat fold down completely

Pull the lever 1 » Fig. 55 and adjust the required inclination of the seat

›

backrest.

WARNING

Check for yourself that the seat backrest is engaged by pulling on it.

67 67

Seats and stowing

Page 70

Fold downseat backrest and seat fold down completely

Fig. 56 Fold seat fully forwards/lock folded forward seats

Folding the seat backrest forwards

Put the belt tongue into the opening on the respective side of the vehicle -

›

safety position. Remove the head restraint from the rear middle seat » page 69, Head re-

›

straints. Push the outer rear seats towards the rear as far as they will go » page 67,

›

Setting theSetting the seats in the longitudinal direction. Pull lever 1 » Fig. 55 on page 67 and fold the seat backrest completely for-

›

wards. Pull lever A » Fig. 56 up and fold the seat forwards fully.

›

Folding seats fully forwards and locking them

If the outer rear seat is fully folded forward, push it towards the rear as far as

›

it can go. Pull lever A » Fig. 56 up and fold the seat forwards fully.

›

Secure the folded forward seat with the aid of the fixing belt B to a guide

›

rod of the head restraint in the front seat » Fig. 56.

WARNING

Immediately lock the folded forward seat with the aid of the fixing belt to a guide rod of the head restraint for the front seat - risk of injury.

CAUTION

■

If the outer seat is not in the rear end position when folding forward, damage

can occur to the locking bolts when unlocking the seat.

■

Only keep the seats in the folded forward position for as long as necessary to transport cargo - there is a risk of damaging the front seat backrests. The seats must be folded back once the cargo has been transported.

Unlocking and removing seats

Fig. 57 Unlocking the folded forward seat/carrying handles on the seat

cushion

Fold the seat forward » page 68, Fold downseat backrest and seat fold down

›

completely .

Unlock the folded seat by pressing seat locks A » Fig. 57 in the direction of

›

arrow 1.

Remove the seat using the carrying handles B or C.

›

Note

The outer seats are not mutually interchangeable. In the rear area the left seat is marked with the letter L and the right seat with the letter R.

Operation

Page 71

Adjusting seats in crosswise direction

Fig. 58

Locking seats

WARNING

■

The belt locks must be in their original position after folding back the seat

cushions and backrests - they must be ready to use.

■

The seat backrests must be securely latched in position so that no objects from the luggage compartment can slip into the passenger compartment under sudden braking – there is a risk of injury.

■

When folding the seat backrest always make sure that it has safely locked into position, this is confirmed by the position and a visible marking on the cover of the lever.

Remove the middle seat » page 68, Unlocking and removing seats.

›

Fold the outer seat forwards » page 68, Fold downseat backrest and seat

›

fold down completely and unlock » Fig. 57 on page 68. Move the folded forward and unlocked seat on the guide towards the middle

›

of the vehicle up to the stop. Lock the folded seat by pressing seat locks A » Fig. 58 in the direction of the

›

arrow.

Folding the rear seats into the starting position

Fig. 59

Folding the seat backrest back into position

If the seat has been removed, first position it on the guide and lock it in

›

place » Fig. 58 on page 69. Pull the seat upwards to ensure that the seat is locked correctly. Fold the seat in the horizontal position until it can be heard to click. Check for

›

yourself that the seat can no longer be lifted by pulling it up. Press the lever » Fig. 59 and fold back the seat backrest. Check for yourself

›

that the seat backrest is engaged by pulling on it. Remove the tongue of the lock from the safety position.

›

Head restraints

Introduction



This chapter contains information on the following subjects: headrest adjust 70

Best protection is achieved if the top edge of the head restraint is at the same level as the upper part of your head.

The head restraints must be adjusted to match the size of the seat occupant. Correctly adjusted head restraints together with the seat belts offer effective protection for the occupants » page 7.

WARNING

■

The head restraints must be correctly adjusted in order to offer effective protection for the occupants in the event of an accident.

■

Never drive with the head restraints removed - risk of injury.

■

If the rear seats are occupied, the rear head restraint must not be in the lower position.

Seats and stowing

Page 72

headrest adjust

Fig. 60 Head restraint: adjusting/removing

Read and observe



Setting height

Grasp the side of the head restraint with both hands and push it upwards as

›

required » Fig. 60 - . To move the head restraint downwards, press and hold the safety but-

›

ton » Fig. 60 -  with one hand and push the head restraint down with the other hand.

Removing/installing

Pull the head restraint out of the seat backrest as far as the stop.

›

Press the locking button in the direction of the arrow » Fig. 60 -  and pull

›

the head restraint out. To re-insert the head restraint, push it far enough down into the seat back-

›

rest until the locking button clicks into place.

on page 69 first.

Boot



Introduction

This chapter contains information on the following subjects: Class N1 vehicles 71

Fastening elements Folding hooks Fixing nets Fixing floor covering of the luggage compartment

Boot cover 72 Net partition 73

Please observe the following for the purpose of maintaining good handling characteristics of your vehicle:

Distribute loads as evenly as possible.

›

Place heavy objects as far forward as possible.

›

Attach the items of luggage to the lashing eyes or using the fixing

›

net » page 71.

In the event of an accident, even small and light objects gain so much kinetic energy that they can cause severe injuries.

The magnitude of the kinetic energy is dependent on the speed at which the vehicle is travelling and the weight of the object.

Example: In the event of a frontal collision at a speed of 50 km/h, an object weighing 4.5 kg produces energy corresponding to 20 times its own weight. This means that it results in a weight of approx. 90 kg “ ”.

WARNING

■

Store the objects in the boot and attach them to the lashing eyes.

■

Loose objects can be thrown forward during a sudden manoeuvre or in

case of an accident and can injure the occupants or other road users.

■

Loose objects could hit a deployed airbag and injure occupants – there is

a risk of death.

■

Please note that transporting heavy objects alters the handling properties of the vehicle due to the displacement of the centre of gravity – risk of accident! The speed and style of driving must be adjusted accordingly.

■

If the items of luggage or objects are attached to the lashing eyes with unsuitable or damaged lashing straps, injuries can occur in the event of braking manoeuvres or accidents. To prevent items of luggage from being thrown forward, always use suitable lashing straps which must be firmly attached to the lashing eyes.

■

The transported items must be stowed in such a way that no objects are able to slip forward on sudden driving or braking manoeuvres – risk of injury!

■

71 72 72

When transporting fastened objects which are sharp and dangerous in the boot that has been enlarged by folding the rear seats forward, ensure the safety of the passengers transported on the other rear seats » page 9, Correct seated position for the passengers in the rear seats.



Operation

Page 73

WARNING (Continued)

■

If the rear seat next to the folded forward seat is occupied, ensure maximum safety, e.g. by placing the goods to be transported in such a way that the seat is prevented from folding back in case of a rear collision.

■

Never drive with the luggage compartment lid open or ajar, as otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning!

■

Under no circumstances should the permissible axle loads and the permissible total vehicle weight be exceeded – risk of accident!

■

Never transport people in the boot!

CAUTION

Please ensure that the heating elements for the rear window heater are not damaged as a result of abrasive objects.

Note

Tyre pressure must be adjusted to the load » page 152, Service life of tyres.

Class N1 vehicles

Read and observe



On class N1 vehicles, which are not fitted with a protective grille, a lashing set which complies with the standard EN 12195 (1 - 4) must be used for fastening the load.

The proper functioning of the electrical system is essential for the safe operation of the vehicle. It is important to ensure that it is not damaged during modifications or when loading or unloading the luggage compartment.

and on page 70 first.

Fastening elements

Fig. 61

Boot: Lashing eyes and fastening elements

Read and observe and on page 70 first.



The following fastening elements are found in the luggage compartment » Fig. 61.

Lashing eyes for fastening items of luggage and fixing nets.

Fastening elements for fastening fixing nets.

CAUTION

The maximum permissible load of the lashing eyes is 3.5 kN (350 kg).

Folding hooks

Fig. 62

Boot: folding hooks

Read and observe and on page 70 first.



Folding hooks » Fig. 62 for attaching small items of luggage, such as bags etc., are provided on both sides of the luggage compartment.

CAUTION

The maximum permissible load of the hook is 7.5 kg.

Seats and stowing

Page 74

Fixing nets

Boot cover

Fig. 63 Fixing net: double horizontal pocket, floor fixing net/double vertical pockets

Read and observe



Fixing examples of the fixing net as a double horizontal pocket, floor fixing net » Fig. 63 -  and double vertical pockets » Fig. 63 - .

WARNING

Do not exceed the maximum permissible load of the fixing nets. Heavy objects are not secured sufficiently – risk of injury!

CAUTION

■

The maximum permissible load of the fixing nets is 1.5 kg.

■

Do not place any sharp objects in the nets – risk of net damage.

and on page 70 first.

Fixing floor covering of the luggage compartment

Read and observe



You can fix the raised floor cover between the backrests and the luggage compartment cover, if one needs to reach the spare wheel.

Operation

and on page 70 first.

Fig. 64 Removing the luggage compartment cover/luggage compartment cover in the lower position

Read and observe



The boot cover can be removed if you wish to transport bulky goods.

Unhook support straps 1 » Fig. 64.

›

Fold the luggage compartment cover forwards a little.

›

Remove the cover from the holders 2 by pulling towards the rear, or by

›

lightly knocking on the underside of the cover in the area between the holders. To reinstall, first of all push the luggage compartment cover into the holders

›

and then hook the support straps 1 on the boot lid.

The luggage compartment cover can also be fitted in the lower position on the supporting elements » Fig. 64 - .

The procedure of installing or removing is identical. In this position you can store smaller objects up on the luggage compartment

cover up to a total weight of 2.5 kg.

WARNING

No objects should be placed on the boot cover, the vehicle occupants could be endangered if there is sudden braking or the vehicle collides with something.

CAUTION

Please ensure that the heating elements for the rear window heater are not damaged as a result of objects placed in this area.

and on page 70 first.



Page 75

Note

When opening the boot lid, the luggage compartment cover is lifted up at the same time- risk that objects placed in this area can slip forward!

Net partition

Put the net partition folded together in the bag and close it.

›

Attach the bag with the aid of the plastic carabines to the eyes on the left

›

and right boot trim panel.

Installing and removing the net partition behind the rear seats is carried out analogously as behind the rear seats. Use the lower fixing eyes on the carrier rails in order to attach the carabines. To enlarge the boot, the rear seats can be removed.

Installing and removing the net partition behind the rear seats with variable loading floor » page 73 is carried out analogously as behind the rear seats without variable loading floor. To attach the carabines, use the lower eyes at the fixing wedges on the front part of the variable loading floor.

The opening D » Fig. 65 in the net partition is designed to pass the threepoint seat belt » page 13, Seat belt for the rear middle seat through.

Fig. 65 Using the net partition behind the front/rear seats

Read and observe and on page 70 first.



The net partition can either be installed behind the rear seats or behind the front seats.

Installing the net partition behind the rear seats

Remove the boot cover » page 72, Boot cover.

›

Remove the net partition from the bag.

›

Unfold both parts of the cross rod until they are heard to engage.

›

First insert the rod into the mount B » Fig. 65 on one side and push it for-

›

wards. In the same way, insert the cross rod into the mount B on the other side of the vehicle. Hang the carabines C at the ends of the belt into the lashing eyes behind

›

the rear seats. Pull the belt through the tensioning clasp on both sides- first of all on the

›

one side and then on the other side.

Removing the net partition

Undo the belts on both sides and unhook the carabiners C » Fig. 65.

›

Push the cross rod first of all on the one side and then on the other side to-

›

wards the rear. Remove the cross rod from the mounts B.

›

Packing the net partition

Press the red button on hinge A » Fig. 65 - the hinge breaks.

›

Variable loading floor in the luggage compartment (Estate)



Introduction

This chapter contains information on the following subjects: Dividing up the luggage compartment with variable loading floor

Removing and refitting the variable loading floor 74 Removing/installing the carrier rails 74 Removing/installing the lateral carrier rail and fixing wedges 75

The variable loading floor makes handling of bulky items of luggage easier.

CAUTION

The maximum permissible load of the variable loading floor is 75 kg.

Note

The room under the variable loading floor can be used to stow objects.

Seats and stowing

Page 76

Dividing up the luggage compartment with variable loading floor

Fig. 66

Dividing the boot

Read and observe on page 73 first.



Lift up the part with the holder and secure it by sliding it into the grooves

›

marked with the arrows » Fig. 66.

Removing and refitting the variable loading floor

Fig. 67

Fold up variable loading floor/remove

Read and observe on page 73 first.



Removing

Unhook the loops A » Fig. 67 of the elastic partition from the fixing points.

›

Unlock the variable loading floor by turning the locking bolts B to the left by

›

around 180°. Fold up the variable loading floor by moving it in the direction of the arrow

›

Fold up the variable loading floor in the direction of the arrow 1 and remove

›

by pulling in the direction of the arrow 2.

Fitting

Fold up the variable loading floor and place it on the carrier rails.

›

Fold out the variable loading floor.

›

Lock the variable loading floor by turning the locking bolts B » Fig. 67 to the

›

right through around 180°. Secure the loops A of the elastic partition to the fixing points.

›

WARNING

Ensure that the carrier rails and variable loading floor are correctly fastened when installing the variable loading floor. If this is not the case, there is a risk of injury for the occupants.

Removing/installing the carrier rails

Fig. 68

Boot: Slacken check points/remove carrier rails

Read and observe on page 73 first.



Removing

Undo the securing points

›

key or a flat screwdriver. Remove the carrier rail A and remove by pulling in the direction of arrow 1.

›

The carrier rail on the other side of the luggage compartment can be removed in the same way.

Fitting

Position the carrier rails on the sides of the boot.

›

Press the securing point B » Fig. 68 on each carrier rail to the stop.

›

Check the attachment of the carrier rails by pulling it.

›

» Fig. 68 on the carrier rails using the vehicle



Operation

Page 77

WARNING

Ensure that the carrier rails and variable loading floor are correctly fastened when installing the variable loading floor. If this is not the case, there is a risk of injury for the occupants.

Removing/installing the lateral carrier rail and fixing wedges

Fig. 69

Boot: Take out lateral carrier rail/Take out fixing wedges

Read and observe on page 73 first.



Removing

Remove the lateral carrier rail » Fig. 69 -  and remove by pulling in the di-

›

rection of arrow. Grip the fixing wedge » Fig. 69 -  and remove by pulling in the direction of

›

arrow. To remove the fixing wedge on the other side of the luggage compartment, proceed in the same way.

Fitting

Put the fixing wedge on the fixing points and press in the direction of the

›

sides of the luggage compartment up to the stop. Insert the lateral carrier rail at an angle to the fixing wedges and press it up

›

to the stop. Check how well the lateral carrier rail is fastened by pulling on it.

›

Bicycle carrier in the luggage compartment

 Introduction

This chapter contains information on the following subjects: Install cross member

Install bicycle carrier 76 Put bicycle into the bicycle carrier 76 Secure the stability of the bicycles with a belt 76

WARNING

When transporting bicycles, ensuring the safety of the passengers is paramount.

CAUTION

Take care handling the bicycle - there is a risk of damaging the vehicle.

Install cross member

Fig. 70

Install cross member

Read and observe and on page 75 first.



Remove the luggage compartment cover » page 72.

›

Fold the rear seats forward, remove » page 68.

›

Undo the securing bolts C » Fig. 70 and remove a little to unlock the holders

›

Place the cross member A with the fixed part onto the right lashing eye and

›

then place it on the left lashing eye with the removable part of the cross member A. Press the holders B until they latch. Tighten the securing screws C.

›

Check how well the cross member is fastened by pulling on it.

›

Seats and stowing

Page 78

Install bicycle carrier

Fig. 71

Install bicycle carrier

Read and observe and on page 75 first.



Position the approved bicycle carrier on the cross member.

›

Remove bolt

›

towards the cross member until the socket latches. Insert the screw A into the nut.

›

Undo the screw B on the movable part of the bicycle carrier and unscrew.

›

Place the movable part of the fixture, depending on the size of the vehicle, in

›

one of the possible positions so that the bicycle does not touch the boot lid. We recommend to place the moveable part of the fixture in such a position that 7 holes are visible between the screw A and the moveable part. Insert the screw B into the desired position and tighten.

›

Put bicycle into the bicycle carrier

Fig. 72

Read and observe and on page 75 first.



Remove the front wheel of the bicycle before installing it.

›

» Fig. 71 a little and push the frame side rail (aluminium part)

Put in the bicycle/example fastening the front wheel

Slacken the quick tension jack on the fixing axle of the bicycle carrier and ad-

›

just according to the width of the bicycle fork. Place the bicycle fork on the fixing axle and tighten with the quick release

›

lever » Fig. 72 - . Position the left pedal of the bicycle forward, in order to attach the front

›

wheel more easily. Undo the bolt A » Fig. 71 on page 76 and push the bicycle carrier to the left

›

together with the mounted bicycle to prevent a collision between the handlebars and the side window of the luggage compartment. Carefully guide the boot lid downwards without letting go of it. Check wheth-

›

er there is sufficient room between the steering bars and the rear window. If necessary, adjust the position of the movable part of the bicycle carrier to prevent a collision » page 76. It is best to store the removed front wheel between the left crank and the

›

bicycle frame, attach it with a strap to the front fork » Fig. 72 -  or to one of the fixing points. The second carrier is installed and the bicycle is secured in a similar way.

›

Secure the stability of the bicycles with a belt

Fig. 73 Securing bicycles

Read and observe and on page 75 first.



To slacken the rubber part of the clamp, push both parts against each other

›

and open the clamp. Position the clamp with the rubber part to the front (in direction of travel) as

›

low down on the seat post as possible and lock it » Fig. 73 - . When transporting two bicycles, stretch the belt » Fig. 73 -  between the

›

saddles by moving the bicycles apart. Hook the carabiners on the ends of the belt into the lashing eyes behind the

›

rear seats » Fig. 73 - .



Operation

Page 79

Pull the belt through the tensioning clasps on both sides in turn.

›

If necessary, you can correct the position of the bicycles in the vehicle.

›

Roof rack system

Introduction



This chapter contains information on the following subjects: Roof load 77

WARNING

■

The transported items on the roof rack must be securely attached – risk of accident!

■

Always secure the load with appropriate and undamaged lashing straps or tensioning straps.

■

Distribute the load evenly over the roof rack system.

■

Transporting heavy or large objects on the roof rack alters the handling properties of the vehicle due to the displacement of the centre of gravity or the increased wind exposure area – risk of accident! The style of driving and speed must therefore be adapted to the current circumstances.

■

Avoid abrupt and sudden driving/braking manoeuvres.

■

Adjust the speed and driving style to the visibility, weather, road and traffic conditions.

■

The permissible roof load, permissible axle loads and permissible total vehicle weight must not be exceeded under any circumstances – risk of accident!

CAUTION

■

Only roof racks from the ŠKODA Original Accessories range should be used.

■

The fitting instructions supplied with the roof luggage rack system must be

observed when handling roof racks.

■

Ensure that the boot lid does not hit the roof load when opened.

■

The height of the vehicle changes after mounting a roof luggage rack system

and the load that is secured to it. Compare the vehicle height with available clearances, such as underpasses and garage doors.

■

Always remove the roof luggage rack system before entering an automated

car wash.

■

Ensure the roof aerial is not impaired by the secured load.

For the sake of the environment

The increased aerodynamic drag results in a higher fuel consumption.

Note

If the vehicle is not factory-equipped with a roof rack, it can be purchased from the ŠKODA Original Accessories.

Roof load

Read and observe and on page 77 first.



The maximum permissible roof load (including roof rack system) of 75 kg and the maximum permissible total weight of the vehicle should not be exceeded.

The full permissible roof load cannot be used if a roof rack system with a lower load carrying capacity is used. In this case, the roof rack system must only be loaded up to the maximum weight limit specified in the fitting instructions.

Useful equipment

Introduction



This chapter contains information on the following subjects: Cupholders

Ashtray 78 Cigarette lighter 79 12-volt power outlet 79 Clothes hook 80 Car park ticket holder 80

WARNING

■

Do not place anything on the dash panel. These objects might slide or fall down while you are driving (under acceleration or when cornering) and could distract you from the traffic - there is a risk of an accident.

■

Make sure that no objects from the centre console or from other storage compartments can get into the driver's footwell while you are driving. You would not be able to brake, operate the clutch pedal or accelerate - danger of causing an accident!

■

Ash and cigarette or cigar stubs must only be discarded in ashtrays.

Seats and stowing

Page 80

Cupholders

Ashtray

Fig. 74 Cup holder

Read and observe



Two beverage containers can be placed in the recesses A » Fig. 74. One beverage container can be placed into the recess B.

WARNING

■

Never put hot cups in the cup holder. They may spill if the vehicle moves –

there is a risk of scalding.

■

No objects should be placed in the holders that might endanger the vehi-

cle's occupants if the vehicle brakes suddenly or the vehicle is in collision.

■

Do not use any cups or beakers made of fragile material (e.g. glass, porce-

lain). This could lead to injuries in the event of an accident.

CAUTION

Do not leave open beverage containers in the cup holder during the journey. There is a risk of spilling e.g. when braking which may cause damage to the electrical components or seat upholstery.

Operation

on page 77 first.

Fig. 75 Centre console: Ashtray at the front/rear

Read and observe



The ashtray can be used for discarding ash, cigarettes, cigars and the like » .

Removing

Pull out the ashtray » Fig. 75 upwards.

›

Fitting

Insert the ashtray vertically.

›

WARNING

Never place flammable objects in the ashtray – risk of fire!

CAUTION

When removing, do not hold the ashtray at the cover – risk of breakage.

on page 77 first.

Page 81

Cigarette lighter

12-volt power outlet

Fig. 76

Centre console: Cigarette lighter

Read and observe on page 77 first.



Operation

Press in the button in the cigarette lighter

›

Wait until the button pops forward.

›

Remove the cigarette lighter immediately and use.

›

Place the cigarette lighter back into the socket.

›

WARNING

■

Take care when using the cigarette lighter! Improper use of the cigarette

lighter can cause burns.

■

The cigarette lighter also operates when the ignition is switched off or the ignition key withdrawn. Therefore, when leaving the vehicle, never leave people who are not completely independent, such as children, unattended in the vehicle. They could operate the igniter and burn themselves.

Note

The cigarette lighter socket can also be used as a 12Volt socket for electrical appliances » page 79.

» Fig. 76.

Fig. 77

Boot: Power socket

Read and observe on page 77 first.



The 12-volt electrical outlet (hereinafter referred to only as a power socket) is located in the front centre console » Fig. 76 on page 79 and in the luggage compartment » Fig. 77.

Use

Remove the cover from power socket or cigarette lighter, or open the cover

›

for the power socket. Connect the plug for the electrical appliance to the socket.

›

The power socket and any connected appliances can also be operated when the ignition is switched off or the ignition key is withdrawn » .

WARNING

■

Improper use of the power sockets and the electrical accessories can cause fires, burns and other serious injuries. Therefore, when leaving the vehicle, never leave people who are not completely independent, such as children, unattended in the vehicle.

■

If the connected electric device becomes too hot, switch it off and disconnect it from the power supply immediately.

CAUTION

■

The 12-volt power socket can only be used for connecting approved electrical

accessories with a total power uptake of up to 120 watt.

■

Never exceed the maximum power consumption, otherwise the vehicle's

electrical system can be damaged.

■

If electrical consumers are switched on when the engine is not running, this

will cause the car battery to discharge – risk of battery discharge!

■

Only use matching plugs to avoid damaging the 12-volt power socket.



Seats and stowing

Page 82

■

Only use accessories that have been tested for electromagnetic compatibility

in accordance with the applicable directives.

■

Before turning the ignition on or off, and before starting the car, switch off the device connected to the 12-volt power socket to prevent any damage caused by voltage fluctuations.

■

Observe the operating instructions for the connected devices!

WARNING

The attached note has to always be removed before starting off in order not to restrict the driver's vision.

Storage compartments

Clothes hook

Read and observe on page 77 first.



The clothes hooks are located on the handle of the headliner above each of the rear doors.

WARNING

■

Ensure that any clothes hanging from the hooks do not impair your vision

to the rear.

■

Only use the hooks for hanging light items of clothing and ensure that

there are no heavy or sharp-edged objects in the pockets.

■

Do not use clothes hangers for hanging up items of clothing otherwise

this may reduce the effectiveness of head airbags.

CAUTION

The maximum permissible load of the hooks is 2 kg.

Car park ticket holder

Fig. 78

Windscreen: Parking ticket holder

Read and observe on page 77 first.



The note holder is designed e.g. for attaching car park tickets.

 Introduction

This chapter contains information on the following subjects: Storage compartment on the front passenger side

Cooling the storage compartment on the front passenger side 81 Storage compartment on the driver's side 81 storage pockets on the front seats 81 sunglasses compartment 82 Storage compartment in the front centre console 82 storage compartment under the front seat 82 Front armrest with storage compartment 83 folding table in the middle back seat 83 slots in the doors 83 stowage compartments in the luggage 84 Flexible storage compartment 84

WARNING

■

Make sure that no objects from the centre console or from other storage compartments can get into the driver's footwell while you are driving. You would then no longer be able to apply the brakes or operate the clutch or accelerator pedal – there is a risk of an accident.

Operation

Page 83

Storage compartment on the front passenger side

Fig. 79

Dash panel: Storage compartments on the front passenger side

Read and observe on page 80 first.



Open/close

Pull the cover handle in the direction of the arrow

›

the cover. Lift the lid upwards until it clicks into place.

›

A pin holder is located inside the lower flap.

WARNING

The storage compartments must always be closed when driving for safety reasons.

» Fig. 79 and fold down

Cooling the storage compartment on the front passenger side

Fig. 80

Storage compartment: Using cooling system

Opening the air supply when the air conditioning system is switched on allows cooled air to flow into the storage compartment.

Opening the air inlet when the air conditioning system is on causes fresh or interior air to flow into the storage compartment.

We recommend closing the air supply if it is operated in heating mode or the cooling system for the storage compartment is not being used.

Storage compartment on the driver's side

Fig. 81

Dash panel: Storage compartment on the driver's side

Read and observe on page 80 first.



The open stowage compartment below the light switch » Fig. 81.

storage pockets on the front seats

Fig. 82

Front seat rests: Map pockets

Read and observe on page 80 first.



Use the rotary switch » Fig. 80 to open and close the air supply.

›

Read and observe on page 80 first.



Map pockets are located on the rear of the seat backrests » Fig. 82. The map pockets are intended for storage of maps, magazines, etc.

Seats and stowing



Page 84

WARNING

Never put heavy items in the map pockets – risk of injury.

CAUTION

Do not put any large items such as bottles or sharp objects into the map pockets, as the pockets and the seat covers could be damaged.

sunglasses compartment

Fig. 83

Detail of the headliner: Glasses storage box

Read and observe on page 80 first.



Press on the bar in the cover of the glasses storage. The compartment folds

›

down » Fig. 83.

WARNING

The compartment must only be opened when removing or inserting the spectacles and otherwise must be kept closed.

CAUTION

■

Do not put any heat-sensitive objects in the glasses storage box - they may

be damaged.

■

The maximum permissible load of the glasses compartment is 250 g.

Storage compartment in the front centre console

Fig. 84

Centre console: Stowage compartment

Read and observe on page 80 first.



The open stowage compartment in the centre console » Fig. 84.

storage compartment under the front seat

Fig. 85

Front seat: Stowage compartment

Read and observe on page 80 first.



Pull the handle to open the lid

›

When closing the lid, hold the handle until the compartment is closed.

›

WARNING

The storage compartment must always be closed when driving for safety reasons.

» Fig. 85.

CAUTION

The storage compartment is designed for storing small objects of up to 1 kg. in weight.

Operation

Page 85

Front armrest with storage compartment

Fig. 86 Armrest: Storage compartment/open storage compartment

Read and observe



Fold the armrest forwards

Press the lower button on the end of the armrest » Fig. 86 - .

›

Fold the arm rest forward and release the button again.

›

Opening the storage compartment

Press the upper button and open the cover of the stowage compartment up-

›

wards » Fig. 86 - .

Note

The moving space of the arms can be restricted if the armrest is folded forwards. In city traffic the armrest should not be folded forwards.

on page 80 first.

folding table in the middle back seat

Fig. 87

Rear seats: Armrest

Read and observe on page 80 first.



The centre seat back can be used as an armrest forward or table with cup holders » Fig. 87 by folding it forwards » page 68, Fold downseat backrest and seat fold down completely .

Two beverage containers can be placed into the recesses.

WARNING

■

Never put hot beverage containers in the cup holder. They may spill if the

vehicle moves – there is a risk of scalding.

■

Do not use any cups or beakers made of fragile material (e.g. glass, porce-

lain). This could lead to injuries in the event of an accident.

CAUTION

■

Do not leave open beverage containers in the cup holder during the journey. There is a risk of spilling e.g. when braking which may cause damage to the electrical components or seat upholstery.

■

If the middle rear seat backrest should be folded forward for lengthy periods, then make sure that the belt locks are not located below it - this can warp the upholstery or fabric.

slots in the doors

Fig. 88 Storage compartment: in the front door/in the rear door

Read and observe on page 80 first.



There is a bottle holder at B » Fig. 88 of the pocket in the front doors.

Seats and stowing



Page 86

WARNING

Use the section A » Fig. 88 of the door pocket only for storing objects which do not project so that the effectiveness of the side airbag is not impaired.

stowage compartments in the luggage

Fig. 89

Storage compartments in the side trim panel

Read and observe on page 80 first.



Storage compartments are located on both sides of the luggage compartment » Fig. 89.

CAUTION

The storage compartments are designed for storing small objects of up to 1.5 kg. in weight in total.

Flexible storage compartment

Fig. 90

Flexible storage compartment

Fitting

Insert both ends of the flexible storage compartment into the openings of

›

the right side trim panel of the boot and push it downwards until it locks.

Removing

Grasp the flexible storage compartment on the two upper corners.

›

Press the upper corners inwards and release the storage compartment by

›

pulling upwards. Remove by pulling towards you.

›

CAUTION

The storage compartment is designed for storing small objects with a maximum total weight of 8 kg.

Note

If the variable loading floor » page 73 is installed in the luggage compartment, no flexible storage compartment can be installed.

Praktik



Introduction

This chapter contains information on the following subjects: Lashings

Adjustable safety partition behind the front seats Attachment of the loading floor Adjustment of the safety partition Emergency release of the loading area door Interior lighting

WARNING

The load to be transported must always be secured safely so that it does not come loose when making an emergency braking or in a vehicle collision which could cause injuries to occupants.

85 85 85

85 86 86

Read and observe on page 80 first.



The flexible storage compartment » Fig. 90 can be fitted to the right-hand side of the luggage compartment.

Operation

Page 87

Lashings

Fig. 91

Loading area: Lashing eyes

Read and observe on page 84 first.



Eyes are located on the sides of the loading area for lashing down the load » Fig. 91.

Adjustable safety partition behind the front seats

Fig. 92

Adjustable safety partition

Read and observe on page 84 first.



The adjustable safety partition behind the front seats can be adjusted up to 100 mm (only valid for certain countries) for improving the comfort for the driver and the front passenger.

Attachment of the loading floor

Fig. 93 Loop for raising the loading floor/Fixing the loading floor with a plastic hook

Read and observe



You can fix the loading floor with a hook on the top edge of the boot lid cutout, in order to e. g. reach the spare wheel.

Raise the loading floor by the loop » Fig. 93 -  and secure it by the plastic

›

hook (located below the loading floor edge) to the top edge of the tailgate cutout » Fig. 93 - .

on page 84 first.

Adjustment of the safety partition

Fig. 94 Top/lower support of the safety partition

Read and observe on page 84 first.



Only valid for some countries.

Raise the loading floor part behind the safety partition.

›

Seats and stowing



Page 88

Undo and remove a bolt » Fig. 94 -  on either side in the upper body and

›

one bolt » Fig. 94 -  in the lower area. Move the safety partition into the required position. Ensure it is always move

›

the same distance- the same number of holes on both sides both upwards and downwards. On each side in the upper area of the body, undo and remove a bolt and undo

›

and remove a bolt in the lower area. Have the tightening torque of the bolts checked with a torque wrench as

›

soon as possible. The tightening torque must be 20 Nm. Change the position of the cover of the luggage compartment floor behind

›

the safety partition so that it lines up with the new position of the safety partition. Fold back the loading floor part.

›

Emergency release of the loading area door

Fig. 95

Emergency unlocking of the loading area door

Read and observe on page 84 first.



If there is a fault in the central locking, you can unlock the loading area door as follows:

Pull the control cable towards you and pull on it.

›

Press on the loading area door to open it.

›

Press the control cable back again.

›

Interior lighting

Fig. 96

Interior lighting

Read and observe on page 84 first.



Switching on

Move the cover glass to the

›

Switching off

Move the cover glass to the O » Fig. 96 position.

›

Door contact setting

Move the cover glass to the middle position  » Fig. 96.

›

Note

We recommend you have the bulb replacement performed by a specialist garage.

position » Fig. 96.



Operation

Page 89

Heating and air-conditioning

Heating, ventilation, cooling

Introduction



This chapter contains information on the following subjects: Air outlets 87

Using the air conditioning system economically 88 Operational problems 88

The heating effect is dependent upon the coolant temperature, thus full heat output only occurs when the engine has reached its operating temperature.

If the cooling system is switched on, the temperature and air humidity drops in the vehicle. The cooling system prevents the windows from misting up when outside temperatures are particularly low.

It is possible to briefly activate recirculated air mode to enhance the cooling effect.

Please refer to the information regarding recirculated air mode for the air-conditioning system » page 91 or for Climatronic » page 93.

WARNING

For your own safety and that of other road users, ensure that all the windows are free of ice, snow and misting. Please familiarize yourself about how to correctly operate the heating and ventilation systems, how to demist and defrost the windows, as well as with the cooling mode.

CAUTION

■

The air inlet in front of the windscreen must be free (e.g. of ice, snow or

leaves) to ensure that the heating and cooling system operates properly.

■

After switching on the cooling Condensation from the evaporator of the air conditioning may drip down and form a puddle below the vehicle. This is not a leak.

Note

■

The exhaust air streams out through vents at the rear of the luggage com-

partment.

■

We recommend that you do not smoke in the vehicle when the recirculating air mode is operating since the smoke which is drawn at the evaporator from the interior of the vehicle forms deposits in the evaporator of the air conditioning system. This produces a permanent odour when the air conditioning system is operating which can only be eliminated through considerable effort and expense (replacement of compressor).

Air outlets

Fig. 97 Air outlet vents

Read and observe and on page 87 first.



Warmed, not warmed fresh or cooled air will flow out of the opened air outlet vents according to the setting of the control and the outside atmospheric conditions.

The direction of airflow can be adjusted using the air outlet vents 3 and

4 » Fig. 97 and the outlets can also be opened and closed individually.

Open the air outlet vents 3 and 4

Turn the vertical wheel (air vents 3) » Fig. 97 or the horizontal wheel (air out-

›

let nozzles 4) to the  position.



Heating and air-conditioning

Page 90

Close air outlet vents 3 and 4

Turn the vertical wheel (air vents 3) » Fig. 97 or the horizontal wheel (air out-

›

let nozzles 4) to the 0 position.

Change air flow of air outlet vents 3 and 4

In order to change the strength of the air flow, swivel the horizontal lamellas

›

with the aid of the moveable adjuster » Fig. 97. In order to change the lateral direction of the air flow, swivel the vertical la-

›

mellas with the aid of the moveable adjuster.

Set the air supply to the individual vents with the air distribution control

» Fig. 98 on page 88.

Note

Do not cover the air outlet vents with objects of any kind.

Using the air conditioning system economically

Read and observe and on page 87 first.



The air conditioning system compressor uses power from the engine when in cooling mode, which will affect the fuel consumption.

It recommended to open the windows or the doors of a vehicle for which the interior has been strongly heated through the effect of direct sunlight in order to allow the heated air to escape.

The cooling system should not be switched on if the windows are open.

For the sake of the environment

Pollutant emissions are also lower when fuel is being saved » page 110.

Operational problems

Read and observe and on page 87 first.



If the cooling system does not operate at outside temperatures higher than +5 °C, there is a problem in the system. The reasons for this may be.

One of the fuses has blown. Check the fuse and replace if necessa-

›

ry » page 168. The cooling system has switched off automatically for a short time because

›

the coolant temperature of the engine is too hot » page 29.

If you are not able to resolve the operational problem yourself, or if the cooler output has reduced, switch off the cooling system and seek assistance from a specialist garage.

Heating

Introduction



This chapter contains information on the following subjects: Operation 88

Setting 89 Recirculated air mode 89

Operation

Fig. 98 Heating: Control elements

Functions of the individual controls » Fig. 98:

Set the temperature (turn to the left: to reduce the temperature, turn to

the right: to increase the temperature)

Set the blower level (level 0: blower off, level 4: the highest blower speed)

Set the direction of the air outlet » page 87

Switch recirculation on/off » page 89



Controls A and C » Fig. 98 can be set to any intermediate position.



Operation

Page 91

WARNING

The blower should always be on to prevent the windows from misting up.

Setting

Recommended basic settings of the heating controls.

Set-up

Defrosting the windshield and side windows

Free windshield and side windows from mist

The fastest heating

Comfortable heating Desired temperature 2 or 3

Fresh air mode - ventilation

To the right up to the

Desired temperature 2 or 3

Control dial settings » Fig. 98 on page 88

A B C

stop

To the stop to the

right

To the stop to the

left

Desired position



  



  



Symbol button



» Fig. 98 on page 88

Do not switch on

Briefly switch on Opening

Do not switch on Opening

Air outlet vents 4 » Fig. 97 on

Open and align with the side

page 87

window

We recommend that you leave the air outlet vents 3 » Fig. 97 on page 87 in the open position in all operating modes.

Note

If the air distribution is set only to the windows, the entire volume of air is used to defrost the windows and thus no air will be fed to the footwell. This can limit the heating comfort.

Recirculated air mode

Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the  button.

›

The indicator light in the button lights up.

Press the  button again.

›

The indicator light in the button goes out.

Recirculated air mode is switched off automatically if the air distribution control C » Fig. 98 on page 88 is turned to the  position. Recirculated air mode can be switched on again from this setting by pressing the  button again.

WARNING

Never leave recirculated air mode on over a longer period of time, as “stale

air” can cause fatigue of the driver and the passengers, reduce attention

levels and also cause the windows to mist up. The risk of having an acci-

dent increases. Switch off recirculated air mode as soon as the windows

start to mist up.

Heating and air-conditioning

Page 92

Air conditioning system (manual air conditioning system)

 Introduction

This chapter contains information on the following subjects: Operation

Setting the air conditioning system 91 Recirculated air mode 91

The cooling system operates only if the following conditions are met.

The cooling system is switched on » page 90.



The engine is running.



The outside temperature is above approximately +2 °C.



The blower switch is switched on (positions 1-4).



If the desired interior temperature can also be achieved without activating the cooling system, fresh air mode should be selected.

If the coolant temperature is too high, the cooling system is switched off to ensure that the engine cools down.

CAUTION

■

Under certain circumstances, air at a temperature of about 5 °C can flow out

of the vents when the cooling system is switched on.

■

Lengthy and uneven distribution of the air flow out of the vents (especially around the feet) and large differences in temperature, for example, when getting out of the vehicle, can cause susceptible individuals to catch a cold.

Note

■

We recommend that you have the air conditioning system cleaned by a specialist garage once every year.

■

During operation of the air conditioning, an increase in engine idle speed may occur under certain circumstances in order to ensure sufficient heating comfort.

Operation

Fig. 99 The air conditioning system: Control elements

Read and observe on page 90 first.



Functions of the individual controls » Fig. 99:

Set the temperature (turn to the left: to reduce the temperature, turn to the right: to increase the temperature)

Set the blower level (level 0: blower off, level 4: the highest blower speed)

Set the direction of the air outlet » page 87



Switch recirculation on/off » page 91



Switch the cooling system on/off

Note

The warning light in the symbol button  lights after activation, even if not all of the conditions for the function of the cooling system are met » page 90. The operational readiness of the cooling system is indicated by the indicator light in the button lighting up.

Operation

Page 93

Setting the air conditioning system

Read and observe on page 90 first.



Recommended basic settings of the air conditioning controls.

Set-up

Defrost/defog windscreen and side windows

The fastest heating

Comfortable heating

The fastest cooling

Optimal cooling

Fresh air mode - ventilation

We recommend that you do not use this setting in countries with high humidity levels. This can result in heavy cooling of the window glass and the following fogging from outside.

Under certain conditions, recirculated air mode » page 91 may come on automatically; the warning light will then light up in the  button.

We recommend that you leave the air outlet vents 3 » Fig. 97 on page 87 in the open position in all operating modes.

Recirculated air mode

Read and observe on page 90 first.



Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the  button.

›

The indicator light in the button lights up.

Press the  button again.

›

The indicator light in the button goes out.

Control dial settings » Fig. 99 on page 90 Button » Fig. 99 on page 90

A B C

Desired tempera-

ture

To the stop to the

right

Desired tempera-

ture

To the left up to

the stop

Desired tempera-

ture

To the stop to the

left

3 or 4

2 or 3

briefly 4, then

2 or 3

1, 2 or 3

Desired position





  

  

Recirculated air mode is switched off automatically if the air distribution control C » Fig. 99 on page 90 is turned to the  position.

Recirculated air mode can be switched on again from this setting by pressing the  button again.

WARNING

Never leave recirculated air mode on over a longer period of time, as “stale air” can cause fatigue of the driver and the passengers, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases. Switch off recirculated air mode as soon as the windows start to mist up.

 

Do not switch on

Briefly switch on Switched off Opening

Do not switch on Switched off Opening

Briefly switch on

Do not switch on Activated Open and align to the roof

Do not switch on Switched off Opening

Automatically switch-

ed on

Activated Opening

Air outlet vents 4 » Fig. 97

on page 87

Open and align with the

side window

Heating and air-conditioning

Page 94

Climatronic (automatic air conditioning system)

 Introduction

This chapter contains information on the following subjects: Control elements

automatic mode 93 Setting the temperature 93 Recirculated air mode 93 Controlling blower 93 Defrosting windscreen 94

The Climatronic in automatic mode ensures the best-possible setting of the temperature of the outflowing air, the blower stage and air distribution.

The system also takes sunlight into account, which eliminates the need to alter the settings manually.

The cooling system operates only if the following conditions are met.

The cooling system is switched on » page 92.



The engine is running.



The outside temperature is above approximately +2 °C.



If the coolant temperature is too high, the cooling system is switched off to ensure that the engine cools down.

Note

■

We recommend that you have Climatronic cleaned by a specialist garage once every year.

■

During operation of the Climatronic, an increase in engine idle speed can occur under certain circumstances in order to ensure adequate heating comfort.

Control elements

Fig. 100 Climatronic: Control elements

The buttons/control dial

Interior temperature setting » page 93

Display

Display of selected interior temperature

Degrees Celsius or Fahrenheit, change the displayed temperature units » page 93

Automatic operation of the air conditioning system

Ventilation or defrosting of the windscreen activated

Direction of air flow

Recirculated air mode activated

Cooling system activated

Blower speed set

The buttons/control dial

Adjust the blower speed » page 93

Interior temperature sensor



Automatic mode » page 93



De-mist or de-ice the windscreen » page 94



Air flow to the windows



Air flow to the upper body



Air flow in the footwell



Operation

Page 95

Switch recirculation on/off » page 93



Switch the cooling system on/off



Note

Do not stick anything on or cover the interior temperature sensor

» Fig. 100; it could have an unfavourable effect on the Climatronic system.

automatic mode

The automatic mode is used in order to maintain a constant temperature and to demist the windows in the interior of the car.

Switching on

Set a temperature between +18 °C and +29 ℃.

›

Move the air outlet vents 3 » Fig. 97 on page 87 and 4 so that the air flow is

›

directed slightly upwards. Press the

›

Automatic mode can be switched off by pressing any of the air distribution buttons or by increasing/decreasing the blower speed. The temperature is nevertheless regulated.

button » Fig. 100 on page 92;



will appear in the display.



Setting the temperature

Setting temperature

Switch on the ignition.

›

Turn the control dial 1 » Fig. 100 on page 92 to the left or to the right to

›

increase or decrease the temperature.

Switching between Celsius and Fahrenheit

Press and hold the

›

The information appears in the display in the desired temperature unit (no.

» Fig. 100 on page 92).

The interior temperature can be set between +18 °C and +29 ℃. The interior temperature is regulated automatically within this range.

If you set the temperature below +18 ℃, “LO” appears in the display. If you set a temperature higher than +29 ℃, “HI” appears in the display. In both end positions, the Climatronic operates at maximum cooling or heating

capacity. There is no automatic temperature control.

and  buttons simultaneously.



CAUTION

Recirculated air mode

Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on

Press the  button » Fig. 100 on page 92.

›

The display shows the  icon.

Switching off

Press the  button » Fig. 100 on page 92 again.

›

The  icon in the display goes out.

WARNING

Note

If recirculated air mode is switched on for around 15 minutes, the symbol  will begin to flash in the display as a sign that the recirculated air mode is switched on long-term. If the recirculated air mode is not switched off, the symbol flashes for around 5 minutes.

Controlling blower

The Climatronic system controls the blower stages automatically in line with the interior temperature. However, the blower level can be manually adjusted to suit your particular needs.

Turn control dial 10 » Fig. 100 on page 92 to the left or to the right to in-

›

crease or decrease the blower speed.

If the blower is switched off, the Climatronic system is switched off.



Heating and air-conditioning

Page 96

The blower speed set is indicated by displaying the corresponding number of segments in icon 9 » Fig. 100 on page 92 in the display.

WARNING

■

“Stale air” may result in fatigue in the driver and occupants, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases.

■

Do not switch off the Climatronic system for longer than necessary.

■

Switch on the Climatronic system as soon as the windows mist up.

Defrosting windscreen

Switching on

Press the  button » Fig. 100 on page 92.

›

Switching off

Press the  button » Fig. 100 on page 92 again or press the

›

More air flows out of the air outlet vents 1 and 2 » Fig. 97 on page 87. The temperature control is controlled automatically.



button.

Communication and multimedia

Universal telephone preinstallation GSM II

Introduction



This chapter contains information on the following subjects: Mobile phones and two-way radio systems 94

Introductory information 95 Phone Phonebook 95 Operating the phone on the multifunction steering wheel 96 Inserting the mobile phone and adapter 96 Managing telephone calls with the help of the adapter 97 Connecting the mobile phone to the hands-free system 97 Symbols in the MAXI DOT display 98 Telephone operation in the MAXI DOT display 98

Mobile phones and two-way radio systems

ŠKODA permits the operation of mobile phones and two-way radio systems with a professionally installed external aerial and a maximum transmission power of up to 10 watts.

Please consult a ŠKODA Partner for information about the possibility of installing and operating mobile phones and two-way radio systems with a transmission power of more than 10 W.

Operating mobile phones or two-way radio systems may interfere with the functionality of the electronic systems in your vehicle.

This could be for the following reasons.

no external aerial.

›

external aerial incorrectly installed.

›

transmission power greater than 10 watts.

›

WARNING

■

Concentrate fully at all times on your driving! As the driver, you are fully

responsible for the operation of your vehicle.

■

Only use the device in such a way that you are in full control of your vehi-

cle in every traffic situation – there is the risk of accidents!



Operation

Page 97

WARNING (Continued)

■

The national regulations for using a mobile phone in a vehicle must be

observed.

■

If a mobile phone or a two-way radio system is operated in a vehicle without an external aerial or an external aerial which has been installed incorrectly, this can increase the strength of the electromagnetic field inside the vehicle.

■

Two-way radio systems, mobile phones or mounts must not be installed on airbag covers or within the immediate deployment range of the airbags.

■

Never leave a mobile phone on a seat, on the dash panel or in another area, from which it can be thrown during a sudden braking manoeuvre, an accident or a collision - risk of injury.

■

The Bluetooth® function must be switched off by a specialist workshop before the vehicle is transported by air.

Note

■

We recommend that mobile phones and two-way radio systems be installed

in the a vehicle by a specialist workshop.

■

Not all mobile phones that enable Bluetooth® communication are compatible

with the universal telephone preinstallation GSM II. You can ask a ŠKODA Partner whether your telephone is compatible with the GSM II universal telephone fitting.

■

The range of the Bluetooth® connection to the hands-free system is restric-

ted to the vehicle interior. The range is dependent on local factors, e.g. obstacles between the devices and mutual interferences with other devices. If your mobile phone is in a jacket pocket, for example, this can lead to difficulties when establishing a connection with the hands-free-system or transferring data.

Introductory information

The universal telephone preinstallation GSM II (hands-free system) includes a convenience mode for the mobile phone via voice control, the multifunction steering wheel, the adapter, radio or the navigation system.

The universal telephone preinstallation GSM II comprises the following functions.

Phone Phonebook » page 95.

›

Convenience operation of the telephone via the multifunction steering

›

wheel » page 96.

Managing telephone calls via the adapter » page 97.

›

Telephone operation in the MAXI DOT display » page 98.

›

Voice control of the telephone » page 99.

›

Music playback from the telephone or other multimedia units » page 100.

›

All communication between a mobile phone and your vehicle's hands-free system is established with the help of Bluetooth® technology. The adapter serves only for charging the telephone and for transmitting the signal to the vehicle's external aerial.

Note

The following guidelines must be observed » page 94, Mobile phones and twoway radio systems.

Phone Phonebook

A phone phonebook is part of the hands-free system. This phone phonebook can be used depending on the type of mobile phone.

After the first connection of the telephone, the system begins to load the phone book from the phone and the SIM card into the memory of the control unit.

Each time the telephone has established a new connection with the handsfree system, an update of the relevant phone book is performed. The updating can take a few minutes. During this time the phone book, which was stored after the last update was completed, is available. Newly stored telephone numbers are only shown after the updating has ended.

The update is interrupted if a telephone event (e.g. incoming or outgoing call, voice control dialogue) occurs during the updating procedure. After the telephone event has ended, the updating starts anew.

The internal phonebook provides 2 500 free memory locations. Each contact can contain up to 4 numbers.

If the number of contacts loaded exceeds 2 500, the phone book is not complete.

Communication and multimedia

Page 98

Operating the phone on the multifunction steering wheel

Fig. 101

Multifunction steering wheel: Mobile phone operation

Button/

wheel

Action Operation

» Fig. 101

2 2 2

Valid for vehicles with the Amundsen+ navigation system.

Valid for vehicles without the Amundsen+ navigation system.

Press briefly Accept call, terminate call, entry in the main menu of the telephone, list of selected numbers

Press button for a long period

of time

Press briefly Switch on/off voice control

Turn upwards Increase the volume

Turn downwards Decrease volume

Inserting the mobile phone and adapter

Fig. 102

Universal telephone preinstallation

There are buttons in the steering wheel for easy operation of the basic functions of the phone » Fig. 101 so that the driver is distracted from the traffic as little as possible when using the phone.

This applies only if your vehicle has been equipped with the universal telephone preinstallation (hands-free system) at the factory.

If the side lights are switched on, the buttons and the symbols  and  on the multifunction steering wheel are illuminated.

Reject call, last number dialleda), switch voice control on/off

Fitting

First of all push adapter A in the direction of the arrow » Fig. 102 into the

›

mount as far as the stop. Then press the adapter slightly downwards, until it locks securely into position. Insert the mobile phone into the adapter A (as specified in the instructions

›

from the manufacturer of the adapter).

Removing

Press the side locks on the mount » Fig. 102 at the same time and remove

›

the adapter with the mobile phone.



Only one telephone mount is factory-fitted. An adapter for the mobile phone can be purchased from ŠKODA Original Accessories.

Operation

Page 99

CAUTION

Taking the mobile phone out of the adapter during the call can lead to interruption of the connection. When removing the mobile phone, the connection to the factory-fitted antenna is interrupted, which reduces the quality of the transmitting and receiving signal. The charging of the mobile phone battery is also interrupted.

Managing telephone calls with the help of the adapter

Fig. 103 Principle sketch: Adapter with one button/adapter with two buttons

Function overview of the  » Fig. 103 (PTT - “push to talk”) button on the adapter.

Switch voice control on/off.

›

Accept/end a call.

›

Some adapters include the ton. After pressing this button for 2 seconds, the number 112 (Emergency call) is dialled.

SOS

button A » Fig. 103 in addition to the  but-

Connecting the mobile phone to the hands-free system

To connect a mobile phone with the hands-free system, the two devices must be paired. Detailed information on this is provided in the operating instructions for your mobile phone.

The following steps must be carried out for the connection.

Activate Bluetooth® and the visibility of your mobile phone on your tele-

›

phone. Switch on the ignition.

›

Select the Phone - New user menu in the MAXI DOT display and wait until

›

the control unit has completed the search. Select your mobile phone from the menu of the units found.

›

Confirm the PIN1).

›

If the hands-free system announces (as standard SKODA_BT) on the display

›

of the mobile phone, enter the PIN1) within 30 seconds and wait, until the connection is established2). To finish pairing, confirm the creation of the new user profile in the MAXI

›

DOT display.

If there is no free space available to create a new user profile, delete an existing user profile.

During the connecting procedure, no other mobile phone may be connected with the hands-free system.

Up to four mobile phones can be paired with the hands-free system, whereby only one mobile phone can communicate with the hands-free system.

The visibility of the hands-free system is automatically switched off 3 minutes after the ignition is switched on and is also deactivated when the mobile phone has connected to the hands-free system.

Restoring the visibility of the hands-free system

If you have not managed to connect your mobile phone with the hands-free system within 3 minutes of switching on the ignition, the visibility of the hands-free system can be reestablished for 3 minutes in the following ways.

By turning the ignition off and on.

›

By turning voice control off and on.

›

In the Bluetooth - Visibility menu in the MAXI DOT display.

›



Depending on the Bluetooth® version on the mobile phone, an automatically generated 6-digit PIN is either displayed or the PIN 1234 has to be entered manually.

Some mobile phones have a menu, in which the authorisation for establishing a Bluetooth® connection is completed by inputting a code. If the authorisation input is required, it must always be performed when re-establishing the Bluetooth connection.

Communication and multimedia

Page 100

Creating a connection with an already paired mobile phone

After switching on the ignition, the connection is automatically established for the already paired mobile phone1). Check on your mobile phone if the automatic connection has been established.

Disconnecting the connection

By withdrawing the ignition key.

›

By disconnecting the hands-free system in the mobile phone.

›

By disconnecting the user in the Bluetooth - Users menu item in the MAXI

›

DOT display.

Solving connection problems Check the operating status of the mobile phone if the system reports No paired phone found.

Is the mobile phone switched on?

›

Is the PIN code entered?

›

Is Bluetooth® active?

›

Is the visibility of the mobile phone active?

›

Has the mobile phone already been paired with the hands-free system?

›

Note

■

If a suitable adapter is available for your mobile phone, only use your mobile phone in the adapter inserted in the telephone mount so that the radiation in the vehicle drops to a minimum.

■

Placing the mobile phone in the adapter inserted in the telephone mount ensures optimum sending and receiving power.

Symbols in the MAXI DOT display

Symbol Meaning



 Signal strength

Charge status of the telephone battery

 a phone is connected to the hands-free system.

Symbol Meaning

 The hands-free system is visible to other devices.



This function is only supported by some mobile phones.

A multimedia unit is connected to the hands-free system.

Telephone operation in the MAXI DOT display

The following menu items can be selected from the Phone menu.

■

Phone book

■

Dial number

■

Call list

■

Voice mailbox

■

Bluetooth

■

Settings

■

Back

Phone book

The Phone book menu item lists the contacts downloaded from the telephone memory and the mobile phone SIM card.

Dial number

Any telephone number can be entered in the Dial number menu item. The required numbers must be selected one after the other using adjustment wheel and confirmed by pressing the adjustment wheel. You can select digits 0-9, symbols , , , # and the Cancel, Call and Delete functions.

Call list The following menu items can be selected in the Call list menu item.

■

Missed calls

■

Dialled numbers

■

Received calls

Voice mailbox

In the Voice mailbox menu item, you can set the number of the voice mailbox and then dial the number.



On vehicles fitted with the Amundsen+ navigation system, this function can be accessed via the navigation system menu; refer to the » Operating instructions for the Amundsen+ navigation system.

This function is not available in vehicles fitted with the Amundsen+ navigation system.

Operation

Skoda Roomster 2014 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Layout of this Owner's Manual (explanations)

Preface

Table of Contents

Abbreviations

Safety

Passive Safety

General information

 Introduction

Before setting off

Driving safety

Safety equipment

Correct and safe seated position

Introduction

Correct seated position for the driver

Adjusting the steering wheel position

Correct seated position for the front passenger

Correct seated position for the passengers in the rear seats

Examples of incorrect seated positions

Seat belts

Using seat belts

Introduction

The physical principle of a frontal collision

Fastening and unfastening seat belts

Belt height adjustment on the front seats

Seat belt for the rear middle seat

Inertia reels and belt tensioners

Introduction

Inertia reels

Belt tensioners

Airbag system

Description of the airbag system

Introduction

System description

Airbag deployment

Airbag overview

Introduction

Front airbags

Side airbags

Head airbags

Deactivating airbags

Introduction

Deactivating airbags

Deactivating the front passenger airbag

Transporting children safely

Child seat

Introduction

Use of a child seat on the front passenger seat

Child safety and side airbag

Classification of child seats

Use of child seats fastened with a seat belt

Fastening systems

Introduction

Anchor eyelets for the ISOFIX system

Use of child seats with the ISOFIX system

Anchor eyelets for the TOP TETHER system

Operation

Cockpit

Overview

Instruments and Indicator Lights

Instrument cluster

Introduction

Overview

Engine revolutions counter

Speedometer

Coolant temperature gauge display

Fuel gauge

Counter for distance driven

Digital clock

Display of the second speed

Recommended gear

Multifunction display (MFD)

Introduction

Memory

Operation

Multifunction display details

Warning against speeding