Škoda Roomster 2013 Owner's Manual
SIMPLY CLEVER
ŠKODA Roomster
Owner's Manual
Layout of this Owner's Manual (explanations)
This Owner's Manual has been systematically designed to make it easy for you to
search for and obtain the information you require.
Chapters, table of contents and subject index
The text of the Owner's manual is divided into relatively short sections which are
combined into easy-to-read chapters. The chapter you are reading at any particular
moment is always specified on the bottom right of the page.
The Table of contents is arranged according to the chapters and the detailed Sub-
ject index at the end of the Owner's Manual helps you to rapidly find the information you are looking for.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of
travel of the vehicle.
Units of measurement
All values are expressed in metric units.
Explanation of symbols
Denotes a reference to a section with important information and safety
advice in a chapter.
Denotes the end of a section.
Denotes the continuation of a section on the next page.
Indicates situations where the vehicle must be stopped as soon as possi-
ble.
® Denotes a registered trademark.
Denotes the display in the MAXI DOT display.
Denotes the display in the segment display.
Display
The display in the segment display will be used in this Owner's Manual to represent
the display unless otherwise specified.
Notes
WARNING
The most important notes are marked with the heading WARNING. These
WARNING notes draw your attention to a serious risk of accident or injury.
CAUTION
A Caution note draws your attention to the possibility of damage to your vehicle
(e.g. damage to gearbox), or points out general risks of an accident.
For the sake of the environment
An Environmental note draws your attention to environmental protection aspects.
This is where you will, for example, find tips aimed at reducing your fuel consumption.
Note
A normal Note draws your attention to important information about the operation
of your vehicle.
Documentation of vehicle handover
Date of delivery/initial registrationa) (VIN)
Vehicle identification number
I confirm that I have taken delivery of the specified vehicle in good condition, have been shown how to operate it correctly, and the terms of the
warranty have been explained to me.
a)
(Whichever comes first).
Vendor's stamp and signature
ŠKODA Partner
Customer's signature
ŠKODA extended warranty
Limits on the ŠKODA extended warranty
Years:
or
km:
a)
(Whichever comes first).
ŠKODA Partner's stamp
Valid from:
a)
Preface
You have opted for a ŠKODA – our sincere thanks for your confidence in us.
You have received a vehicle with the latest technology and range of amenities. Please read this Owner's
Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use
of the vehicle.
If you have any questions about your vehicle, please contact a ŠKODA Partner.
We hope you enjoy driving your ŠKODA, and wish you a pleasant journey at all times.
Your ŠKODA AUTO a.s. (hereinafter referred to only as ŠKODA or manufacturer)
Terms used
The on-board literature contains the following terms relating to the service work
for your vehicle.
“Specialist garage” - a workshop that carries out specialist service tasks for
›
ŠKODA vehicles A specialist garage can be a ŠKODA partner, a ŠKODA service
partner or an independent workshop.
“ŠKODA service partner” - A Workshop that has been contractually authorized
›
by the manufacturer ŠKODA AUTO a.s. or its sales partner to perform service
tasks on ŠKODA vehicles and to sell ŠKODA Genuine Parts.
“ŠKODA partner” - A company that has been authorized by the manufacturer
›
ŠKODA AUTO a.s. or its sales partner to sell new ŠKODA vehicles and, when applicable, to service them using ŠKODA Genuine Parts and sell ŠKODA Genuine
Parts.
Owner's Manual
These operating instructions apply to all body variants of the vehicle and all related models.
The manual describes all possible equipment variants without identifying them
as special equipment, model variants or market-dependent equipment.
Consequently, this vehicle does not necessarily contain all of the equipment
components described in this Owner's Manual.
The scope of equipment on your vehicle depends on your purchase contract for
the vehicle. More information is available from the ŠKODA Partner from whom you
bought the vehicle.
The illustrations can differ in minor details from your vehicle; they are only intended for general information.
Table of Contents
Materials defect liability and ŠKODA warranty for
new cars 5
Mobility warranty and ŠKODA extended
warranty
Abbreviations
Operation
Cockpit
Overview
Instruments and Indicator Lights 10
Instrument cluster
Multifunction display (MFD)
Service Interval Display 16
MAXI DOT display
Warning lights 20
Unlocking and locking
Unlocking and locking
Central locking system 31
Remote control
Anti-theft alarm system 35
Luggage compartment lid
Electrical power windows
Lights and visibility 41
Lights
Interior lights 46
Visibility
Windscreen wipers and washers
Rear window 51
Seats and stowing
Front seats 52
Rear seats
28
28
34
38
47
48
52
54
Head restraints 56
Boot 57
Variable loading floor in the luggage
compartment (Estate) 61
Bicycle carrier in the luggage compartment 63
Roof rack system 65
Useful equipment 65
6
Storage compartments 68
Praktik 73
Heating and air-conditioning 77
Heating, ventilation, cooling 77
Heating 78
Air conditioning system (manual air conditioning
9
system)
8
Climatronic (automatic air conditioning
system)
10
Communication and multimedia
13
Universal telephone preinstallation GSM II 86
Voice control
18
Multimedia
Driving
Starting-off and Driving 95
Steering
Starting and stopping the engine 96
37
Brakes
Manual gear changing and pedals
Automatic transmission 100
Running in
41
Economical driving and environmental
sustainability
Avoiding damage to your vehicle
Driving abroad 109
Assist systems
Brake assist systems 110
Parking aid
Cruise Control System 113
START-STOP 115
Towing a trailer 117
Towing device 117
Trailer 120
Safety
Passive Safety
General information 123
Correct seated position 124
Seat belts 127
Using seat belts 127
80
Inertia reels and belt tensioners 130
Airbag system
83
Description of the airbag system 132
86
Airbag overview
Deactivating airbags
91
Transporting children safely 139
92
Child seat
Fastening systems 141
General Maintenance
95
Car care
Service intervals
98
Services, modifications and technical
99
alterations 146
Washing your car 149
103
Taking care of your vehicle exterior
Taking care of the interior
104
108
Inspecting and replenishing 157
Fuel
Engine compartment 159
110
Engine oil
Coolant
112
123
132
133
136
139
144
144
150
154
157
163
165
Table of Contents
3
Brake fluid 167
Vehicle battery 168
Wheels 172
Tyres and wheel rims 172
Winter operation 178
Do-it-yourself
Emergency equipment and self-help
Emergency equipment 179
Changing a wheel 180
Tyre repair 184
Jump-starting 186
Towing the vehicle 188
Fuses and light bulbs
Fuses 191
Bulbs
179
191
194
Technical data
Technical data
Vehicle data 199
199
Index
4
Table of Contents
Materials defect liability and ŠKODA warranty for new cars
Materials defect liability
Your ŠKODA partner, as a vendor, is liable to you for defects in your new ŠKODA
car, ŠKODA Genuine Parts or ŠKODA Genuine Accessories in accordance with statutory regulations and the purchase agreement.
ŠKODA warranty for new cars
As well as the materials defect liability, ŠKODA AUTO a.s. grants you the ŠKODA
warranty for new cars (hereafter referred to as “ŠKODA warranty),” according to
the terms described below.
As part of the ŠKODA warranty, ŠKODA AUTO a.s. will guarantee the following
services:
Repair of damage to your vehicle that occurs within two years from the start of
›
the ŠKODA warranty;
Repair of paint damage to your vehicle that occurs within three years from the
›
start of the ŠKODA warranty;
Repair of rust perforation to the bodywork of your vehicle that occurs within
›
twelve years from the start of the warranty. Only rust perforation from the inside to the outside of body panels is considered to be rust perforation of the
bodywork and is covered by the ŠKODA warranty.
The start of the warranty is the date on which the original purchaser acquires the
vehicle upon purchasing it from the ŠKODA partner or the date of first registration. Whichever occurs first and is accordingly recorded by the ŠKODA partner in
the service schedule is the applicable date.
Defects may be remedied by replacement or repair of the defective part. Replaced
parts become the property of the ŠKODA service partner.
There are no other entitlements arising from the ŠKODA warranty. In particular,
there are no entitlements to replacement, cancellation, provision of a courtesy
vehicle for the duration of repairs or compensation for loss.
If your ŠKODA vehicle was purchased from a ŠKODA partner in a country within
the European Economic Area (i.e. the countries of the European Union, Norway,
Iceland and Liechtenstein) or in Switzerland, claims arising from the ŠKODA warranty must also be made through a ŠKODA service partner in one of these countries.
If your ŠKODA vehicle has been purchased from a ŠKODA partner outside the European Economic Area and Switzerland, claims arising from the ŠKODA warranty
must also be made through a ŠKODA service partner outside the European Economic Area and Switzerland.
One of the conditions for the assertion of the ŠKODA warranty is that all service
operations have been carried out works in a timely and adequate manner and in
accordance with the manufacturer's provisions. You must prove that service operations have been carried out properly and in accordance with the manufacturer's
provisions when asserting a claim under the ŠKODA warranty. Where a service
has been missed or not carried out according to the manufacturer's provisions,
you may still be entitled to warranty claims as long as you can prove that the
missed service or the failure to carry out a service according to the manufacturer's provisions was not the cause of the defect.
Natural wear and tear of your vehicle is not covered by the ŠKODA warranty. The
ŠKODA warranty also does not cover defects to bodywork, installations and conversions provided by third-parties, nor vehicle defects caused by these. The same
is true for accessories which are not factory installed and/or supplied.
In addition, this warranty does not apply if the defect was caused by one of the
following:
unauthorized use, improper handling (e.g. use in motorsport competitions or
›
overloading), improper care and maintenance, or unapproved modification to
your vehicle;
non-compliance with provisions in the service schedule and the Owner's manual
›
or other factory-supplied instructions;
external causes or influences (e.g. accidents, hail, flooding, etc.);
›
parts fitted or installed on the vehicle the use of which is not approved by
›
ŠKODA AUTO a.s., or modification of the vehicle in a manner not approved by
ŠKODA AUTO a.s. (e.g. tuning);
damage caused by you which was not immediately seen to by specialist garage
›
or was not fixed properly.
It is the customer's responsibility to prove that it was not the cause.
This ŠKODA warranty does not affect the purchaser's statutory rights arising from
liability for defects by the vehicle vendor and other potential claims under product
liability laws.
Materials defect liability and ŠKODA warranty for new cars
5
Mobility warranty and ŠKODA extended warranty
Mobility warranty
Mobility warranty provides a sense of security when travelling in your vehicle.
Should your car break down when you're on the move one day as a result of an
unexpected fault, you will be eligible for services to ensure your continued mobility as part of the mobility warranty, which includes the following: Breakdown service at the breakdown location and towing to the ŠKODA service partner, technical
assistance by phone or in person.
If your vehicle is not repaired on the same day, the ŠKODA service partner may
provide further services as required, such as replacement transportation (bus,
train, etc.), a courtesy vehicle, etc.
You can obtain more information regarding terms and conditions for the provision
of mobility warranty for your vehicle from your ŠKODA partner. Here you will also
be given detailed terms and conditions of the mobility warranty as it relates to
your vehicle. In the event that there is no mobility warranty coverage available for
your vehicle, you should check with any ŠKODA service partner about the possibility of concluding a contract retrospectively.
Note
The mobility warranty is only available in some countries.
Optional ŠKODA extended warranty
If you received an extended ŠKODA warranty when purchasing your new car, the
two-year ŠKODA warranty for defects in your ŠKODA vehicle will be extended by
the period you chose or until the chosen mileage limit has been reached.
The paintwork warranty and the warranty against rust perforation referred to
above stay unaffected by the extended warranty.
Detailed conditions for the extended warranty are included in the extended warranty terms and conditions, which your ŠKODA partner will have given you when
you purchased your new vehicle.
Note
The mobility guarantee and optional extended ŠKODA warranty are only available
in some countries.
6
Mobility warranty and ŠKODA extended warranty
Abbreviations
Abbreviation Definition
rpm Engine revolutions per minute
ABS Anti-lock brake system
AG Automatic gearbox
TCS Traction control
CO2 in g/km discharged quantity of carbon dioxide in grams per driven kilo-
meter
DPF Diesel particle filter
DSG Automatic double clutch gearbox
ECE Economic Commission for Europe
ESC Electronic Stability Control
EU European Union
kW Kilowatt, measuring unit for the engine output
MG Manual gearbox
MFD Multifunction display
N1 Panel van intended exclusively or mainly for the transporta-
tion of goods
Nm Newton meter, measuring unit for the engine torque
TDI CR Diesel engine with turbocharging and common rail injection
system
TSI Petrol engine with turbocharging and direct injection
Abbreviations
7
8
Fig. 1
Cockpit
Operation
Operation
Cockpit
Overview
1
Door handle 30
2
Electrical power windows 38
3
Electric exterior mirror adjustment 51
4
Air outlet vents 77
5
Car park ticket holder 68
6
Operating lever:
Turn signal light, headlight and parking light, headlight flasher 43
›
Speed regulating system
›
7
Steering wheel:
With horn
›
With driver’s front airbag
›
With pushbuttons for radio, navigation system and mobile
›
phone 86
8
Instrument cluster: Instruments and warning lights 10
9
Operating lever:
Windscreen wiper and wash system
›
Multifunction display 13
›
MAXI DOT display
›
10
Button for rear window heater 47
11
TCS switch
12
Air outlet vents in the central part of the instrument panel 77
13
Button for hazard warning light system
14
Warning light for the deactivated front seat passenger airbag
15
Depending on equipment fitted:
Operating controls for the heating 78
›
Operating controls for the air conditioning system 80
›
Operating controls for Climatronic
›
16
Storage compartments on the front passenger side
17
Front passenger airbag 134
18
Air outlet vents
19
Key-operated switch for the front seat passenger airbag 137
20
Door handle 30
21
Switch depending on equipment fitted:
Boot lid remote release 37
›
Interior monitor 36
›
22
Light switch and headlamp beam adjustment 41, 42
23
Fuse box in the dashboard 192
24
Bonnet release lever 161
25
Lever for adjusting the steering wheel 95
26
Ignition lock 97
27
Pedals 100
28
Depending on equipment fitted:
Gear lever (manual gearbox) 99
›
Selector lever (automatic gearbox) 101
›
29
Rocker switch for front left seat heating
30
113
134
49
18
Central locking system 33
31
Handbrake
32
Rocker switch for front right seat heating 53
33
Depending on equipment fitted:
Ashtrays
›
Storage compartment 71
›
34
Depending on equipment fitted:
Radio
›
Navigation system
›
35
MDI
Note
111
The arrangement of the controls right-hand drive models may differ from the layout shown in » Fig. 1. The symbols on the controls and switches are the same as
45
for left-hand drive models.
137
83
69
77
53
99
66
94
Cockpit
9
Instruments and Indicator Lights
Instrument cluster
Introduction
This chapter contains information on the following subjects:
Overview
Engine revolutions counter 11
Speedometer 11
Coolant temperature gauge display 11
Fuel gauge 11
Counter for distance driven 12
Digital clock
Display of the second speed 12
Recommended gear
Fault display
The Error message will appear in the display if there is a fault in the instrument
cluster. Ensure that the fault is rectified as soon as possible by a specialist workshop.
WARNING
■
Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for road safety.
■
Never operate the controls in the instrument cluster while driving, only
when the vehicle is stationary!
Overview
10
Fig. 2 Instrument cluster
12
13
1
Rev counter with warning lights » page 11
2
Display:
›
›
›
›
›
3
Speedometer with warning lights » page 11
4
Coolant temperature gauge1) » page 11
5
Button for display mode:
›
›
›
First read and observe the introductory information and safety warnings on page 10.
With counter for distance driven » page 12
With service interval display » page 16
With digital clock » page 12
with multifunction display (MFD) » page 13
with the Maxi DOT display » page 18
Setting the hours/minutes » page 12
Enable/disable display of the second speed2) » page 12
Service interval2) - Display of the number of days, kilometres or miles remaining until the next Service3) » page 16
1)
Applies for vehicles using the MAXI DOT display.
2)
Applies for vehicles with a segment display.
3)
Applies for models in which where the values are indicated in British measuring units.
10
Operation
6
Button for:
Reset trip meter » page 12
›
Set hours/minutes
›
Enable/disable the mode selected by means of button
›
7
Fuel gauge1) » page 11
5
Engine revolutions counter
First read and observe the introductory information and safety warnings on page 10.
The red scale range of the rev counter 1 » Fig. 2 on page 10 indicates the range
in which the engine control unit begins to limit the engine speed. The engine control unit restricts the engine speed to a steady limit.
You should shift into the next higher gear before the red scale of the revolution
counter is reached, or move the selector lever into position D if your car is fitted
with an automatic gearbox.
To maintain the optimum motor speed, observe the gearshift indicator » page 13.
For the sake of the environment
Shifting up in good time has the following benefits.
■
It helps to reduce fuel consumption.
■
It reduces engine noise.
■
It protects the environment.
■
It benefits the life and reliability of the engine.
Speedometer
First read and observe the introductory information and safety warnings on page 10.
Warning against speeding
An audible warning will sound when the vehicle speed exceeds 120 km/h2). The
audible warning is switched off once the vehicle speed falls below 120 km/h.
Coolant temperature gauge display
First read and observe the introductory information and safety warnings on page 10.
The coolant temperature gauge 4 » Fig. 2 on page 10 works only when the ignition is switched on.
In vehicles with a segment display, the coolant temperature is indicated only by
one of the warning lights » page 22, Coolant coming on or going off.
Cold range
The pointer in the left of the scale indicates that the engine has not yet reached
its operating temperature. Avoid high speeds, full throttle and high engine loads.
This prevents possible damage to the engine.
The operating range
The engine has reached its operating temperature as soon as the pointer moves
into the middle of the scale. At very high ambient temperatures or under heavy
engine loads, the pointer may move even further to the right.
High temperature range
The coolant temperature is too high if the pointer reaches the red area of the
scale. Further information » page 22.
CAUTION
Additional headlights and other components mounted in front of the air inlet impair the cooling efficiency of the coolant.
Fuel gauge
First read and observe the introductory information and safety warnings on page 10.
The fuel gauge 7 » Fig. 2 on page 10 only works when the ignition is switched
on.
The fuel remaining is displayed in the segment display on vehicles with the seg-
ment display.
1)
Applies for vehicles using the MAXI DOT display.
2)
This function is only enabled in certain countries.
Instruments and Indicator Lights
11
The fuel tank has a capacity of about 45 litres. The warning light lights up when
the fuel level reaches the reserve range » page 25.
CAUTION
Never drive until the fuel tank is completely empty! The irregular supply of fuel
can cause misfiring. This can result in considerable damage to parts of the engine
and the exhaust system.
Counter for distance driven
First read and observe the introductory information and safety warnings on page 10.
The distance which you have driven with your vehicle is shown in km. In some
countries the measuring unit “mile” is used.
Daily trip counter (trip)
The trip counter indicates the distance you have driven since it was last reset - in
steps of 100 metres or 1/10 of a mile.
Reset trip meter
The meter can be reset by pressing and holding button
Odometer
The odometer indicates the total distance in kilometres or miles which the vehicle
has been driven.
6
» Fig. 2 on page 10.
Note
If the second speed display is enabled on vehicles with a segment display, this
speed will be shown instead of the odometer.
Digital clock
First read and observe the introductory information and safety warnings on page 10.
The clock is set with buttons 5 and 6 » Fig. 2 on page 10.
Select the display that you wish to change with the button 5 and carry out the
change with the button 6.
In vehicles equipped with the MAXI DOT display, it is also possible to set the clock
in the Time menu » page 18.
Display of the second speed
First read and observe the introductory information and safety warnings on page 10.
The display can show the current speed in mph1).
This feature is provided for driving in countries with different units for speed.
MAXI DOT display
The display of the second speed can be set in the Settings menu item » page 18,
Settings.
Segment display
Press the 5 » Fig. 2 on page 10key repeatedly, until the odometer display flash-
›
es » page 12.
Press the 6 key while the display is flashing.
›
The second speed is displayed instead of the odometer.
Display of the second speed can be disabled in the same way.
1)
On models on which the speedometer indicates mph, the second speed is displayed in km/h.
12
Operation
Recommended gear
Fig. 3
Recommended gear
First read and observe the introductory information and safety warnings on page 10.
The gear currently engaged is shown in the instrument cluster display A » Fig. 3.
In order to minimise the fuel consumption, a recommendation for shifting into an-
other gear is indicated in the display.
If the control unit recognises that it is beneficial to change gear, an arrow B is
shown in the display. The arrow points up or down, depending on whether you
should shift into a higher or lower gear.
At the same time, the recommended gear is shown at
lected on vehicles with a manual gearbox.
A
instead of the gear se-
CAUTION
The driver is always responsible for selecting the correct gear in different driving
situations, such as overtaking.
Multifunction display (MFD)
Multifunction display details 15
Warning against speeding 16
The multifunction display can only be operated when the ignition is switched on.
After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
The multifunction display shown in the segment display » Fig. 4 on page 14 or in
the MAXI DOT display depending on your vehicle model » page 18.
On vehicles with a MAXI DOT display » page 18, there is an option not to display
some of the information.
WARNING
■
Concentrate fully on your driving at all times. As the driver you are fully re-
sponsible for the operation of your vehicle.
■
Even at temperatures of around +4 °C, there may still be black ice on the
road surface. You should therefore not rely solely on the outside temperature
display for accurate information as to whether there is ice on the road.
Note
■
In certain national versions the displays appear in the Imperial system of meas-
ures.
■
If the display of the second speed is activated in mph, the current speed is not
indicated in km/h on the display.
Introduction
This chapter contains information on the following subjects:
Memory 14
Operation 14
Instruments and Indicator Lights
13
Memory
Fig. 4
Multifunction display
First read and observe the introductory information and safety warnings on page 13.
The multifunction display is equipped with two automatic memories. The selected
memory is shown in the Display » Fig. 4.
The data of the single-trip memory (memory 1) is shown if a 1 appears in the display. A 2 shown in the display means that data relates to the total distance memory (memory 2).
Switch memories using button
stalk.
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued within 2 hours
after switching off the ignition. If the trip is interrupted for more than 2 hours,
the memory is automatically erased.
Total-trip memory (memory 2)
The total trip memory collates the data from any number of individual trips up to
a total of 19 hours and 59 minutes or 1999 km or, for vehicles with a MAXI DOT
display, 99 hours and 59 minutes, or 9999 km. The memory is deleted when either of these limits is reached and the calculation starts all over again.
Unlike the single-trip memory, the total-trip memory is not deleted after a period
of interruption of driving of 2 hours.
B
» Fig. 5 on page 14 on the windscreen wiper
Note
All information in the memory 1 and 2 is erased if the battery of the vehicle is disconnected.
Operation
Fig. 5
Multifunction display: Control elements
First read and observe the introductory information and safety warnings
The Toggle button for selecting menu items A » Fig. 5 and button B are found
on the wiper stalk.
Select menu items
Briefly press the top or bottom of rocker switch A » Fig. 5. This opens the indi-
›
vidual menu items in the multifunction display one after the other.
Select memory
Press button B » Fig. 5.
›
Reset memory
Select the desired memory.
›
Press and hold button B » Fig. 5.
›
The following values from the memory selected will be set to zero by button B.
Average fuel consumption.
›
Distance driven.
›
Average speed.
›
Driving time
›
on page 13.
14
Operation
Multifunction display details
First read and observe the introductory information and safety warnings on page 13.
Outside temperature
The current outside temperature is displayed1).
The temperature is shown with the snowflake symbol (ice warning) if the out-
door temperature is below +4 °C.
This display flashes for a few seconds, then shows the most recently displayed
function2) .
If the temperature drops below +4 °C while the car is driving at a speed faster
than 10 km / h, a beep is also heard.
Driving time
The driving time elapsed since the memory was last erased appears in the display.
Reset the memory to zero by pressing the button » page 14, Operation to measure the driving time from a particular moment.
The maximum time indicated in both memories is 19 hours and 59 minutes and on
vehicles which are fitted with a MAXI DOT display, it is 99 hours and 59 minutes.
The indicator is set back to zero when this period is exceeded.
Current fuel consumption
The current fuel consumption level is displayed in litres/100 km3). You can use this
information to adapt your driving style to the desired fuel consumption.
The display appears in litres/hour if the vehicle is stationary or driving at a low
speed4).
Average fuel consumption
The average fuel consumption since the memory was last erased is displayed in
litres/100 km3).
Set the memory to zero at the start of a new measurement if you wish to determine the average fuel consumption over a certain period » page 14, Operation. No
value will appear in the display after it has been erased until you have driven approximately 300 m.
The display is updated regularly while you are driving.
Range
The estimated range is displayed in kilometres. It indicates the distance you can
still drive with your vehicle based on the level of fuel in the tank and the same
style of driving.
The display is shown in steps of 10 km. The value is displayed in steps of 5 km
after the has come on.
The fuel consumption over the preceding 50 km is used to calculate the information. The range will increase if you drive in a more economical manner.
If the memory is set to zero (after the battery has been disconnected), a fuel consumption of 10 l/100 km is used initially, then the value is adapted according to
the style of driving.
Distance travelled
The distance travelled since the memory was last erased is displayed. Reset the
memory to zero if you want to measure the distance travelled from a particular
moment » page 14, Operation.
The maximum distance indicated in both memories is 1999 km or 9999 km on vehicles with a MAXI DOT display. The indicator is set back to zero when this period
is exceeded.
Average speed
The average speed since the memory was last erased is displayed in km/hour .
Set the memory to zero at the start of measurement to determine the average
speed over a certain period » page 14, Operation.
No value will appear in the display until you have driven approximately 300 m after this information has been deleted.
The display is updated regularly while you are driving.
1)
This information is always shown on vehicles with a MAXI DOT display.
2)
This is not the case on the MAXI DOT display.
3)
On some models in certain countries, the display appears in kilometres/litre.
4)
On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is stationary.
Instruments and Indicator Lights
15
Current speed
The current speed, identical to the display on the speedometer 3 » Fig. 2 on
page 10, is displayed.
Oil temperature
The current engine oil temperature is displayed. If the oil temperature is lower
than 50 °C or if a fault in the system for checking the oil temperature is present,
only - -.- is displayed instead of the oil temperature.
Warning against speeding
The warning that the speed limit is being exceeded can be enabled/disabled in
the display» page 16.
1)
Change or delete speed limit
Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)
›
or (segment display) menu item.
Pressing button B disables the speed limit.
›
Pressing the button B activates the ability to change the speed limit.
›
If the set speed limit is exceeded, an audible signal will sound as a warning. The
Warning at (MAXI DOT display) or (segment display) menu item appears in the
display with the limit set.
The speed limit set mode is stored even after the ignition is switched off and on.
Warning against speeding
First read and observe the introductory information and safety warnings on page 13.
Adjust the speed limit while the vehicle is stationary
Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)
›
or (segment display) menu item.
Press button B to activate the ability to set the speed limit2) (value flashes).
›
Use button A to set the required speed limit, e.g. 50 km/h.
›
Confirm the speed limit that was set with button B, or wait approx. 5 seconds
›
until the setting is saved automatically (the value stops flashing).
This allows you to set the speed in 5 km/h intervals.
Adjusting the speed limit while the vehicle is moving
Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)
›
or (segment display) menu item.
Drive at the desired speed, e.g. 50 km/h.
›
Press button B to accept the current speed as the speed limit (the value flash-
›
es).
If you wish to adjust the set speed limit, you can do so in 5 km/h intervals (e.g. the
accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).
Confirm the speed limit that was set by pressing button B again, or wait ap-
›
prox. 5 seconds until the setting is saved automatically (the value stops flashing).
1)
Applies for vehicles using the MAXI DOT display.
2)
An initial value of 30 km/h is displayed automatically if no value has been specified.
16
Operation
Service Interval Display
Introduction
This chapter contains information on the following subjects:
Prompt in the segment display
Display in the MAXI DOT display
Before the next service interval is reached, a message concerning the kilometres
and days remaining until the next service is due is shown for about 10 seconds
after the ignition is switched on.
The kilometre indicator or the days indicator reduces in steps of 100 km or days
until the service due date is reached.
Note
■
Information is retained in the Service Interval Display even after the vehicle bat-
tery is disconnected.
■
If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by
a specialist garage.
■
For more information on the service intervals » page 144, Service intervals.
17
17
Prompt in the segment display
Fig. 6
Example of a message
First read and observe the introductory information given on page 16.
Oil change service
If an oil change service is due, the icon and the number 1 is displayed at the
position identified with the arrow for approximately 10 seconds » Fig. 6.
The icon is shown together with the days and kilometres remaining to the next
service.
As soon as the service due date is reached, the flashing icon and the message
OIL CHNG appears in the display for about 20 seconds after the ignition is switched on.
Inspection
If an inspection is due, the icon and the number 2 are displayed at the position
identified with the arrow for approximately 10 seconds » Fig. 6.
The icon is shown together with the days and kilometres remaining to the next
service.
As soon as the due date for the service is reached, the flashing icon and the
INSPEC _ message appear in the display for about 20 seconds after the ignition
has been switched on.
Display the days and distance until the next service
You can press button
distance and time to until the next service whenever the ignition is switched on.
The icon appears together with the icon and the distance and time to the
next service appear in the display for about 10 seconds.
5
» Fig. 2 on page 10 repeatedly to display the remaining
The distance and the days remaining until the next oil change service are displayed first; the distance and the days remaining until the next inspection are
displayed after the button 5is pressed again.
Note
The kilometres remaining until the next service are displayed instead of the odometer.
Display in the MAXI DOT display
First read and observe the introductory information given on page 16.
Oil change service
If an oil change service is due, the message Oil change in ... km or .... days ap-
pears.
As soon as the service date has arrived, the message Oil change now! appears after the ignition is switched on.
Inspection
If an inspection is due, the message Inspection in ... km or ... days appears.
As soon as the service interval date has arrived, the message Inspection now! ap-
pears after the ignition is switched on.
Displaying the distance and days until the next service interval
You can display the remaining distance and days until the next service in the Settings menu whenever the ignition is switched on » page 18.
The following message is displayed for 10 seconds.
Oil change ... km / ... days
Inspection ... km / ... days
Instruments and Indicator Lights
17
MAXI DOT display
Introduction
This chapter contains information on the following subjects:
Main menu
Settings 18
Door, boot lid and bonnet warning 19
Auto Check Control 19
The MAXI DOT display provides you with information about the current operating
state of your vehicle. The information system also provides you with data (depending on the vehicle equipment) relating to the radio, mobile phone, multifunctional display, navigation system, the device connected to the MDI input and
the automatic gearbox » page 100.
Lighting up of certain symbols is combined with an acoustic warning signal.
WARNING
Concentrate fully on your driving at all times. As the driver you are fully responsible for the operation of your vehicle.
Main menu
Fig. 7
Operating lever: MAXI DOT display controls
First read and observe the introductory information and safety warnings on page 18.
Press and hold rocker switch A » Fig. 7 to activate the MAIN MENU.
›
Individual menu items can be selected by pressing rocker switch A. When the
›
pushbutton B is briefly pressed, the information you have selected is dis-
played.
Overview of the menu items in the main menu.
■
MFD (Multifunction display) » page 13
■
Audio » Operating instructions for the radio
■
Navigation » Operating instructions for the navigation system
18
■
Phone » page 86;
■
Vehicle status » page 19
■
Settings » page 18
The Audio and Navigation menu items are only displayed when the factory-fitted
radio or navigation system is switched on.
Note
■
Warning messages shown in the information display must be confirmed by
pressing button B briefly » Fig. 7 to call up the main menu.
■
The menu always shifts to one of the higher levels after 10 seconds if the display is not currently active.
■
Using the factory-fitted radio or navigation system » Radio operating instructions or» Navigation system operating instructions.
Settings
First read and observe the introductory information and safety warnings on page 18.
You can change certain settings yourself through the MAXI DOT display. The current menu item is shown in the top of the display under a line.
You can select the following menu options:
Language
You can set the language for the warning and information texts here.
MFD data
Activate or deactivate certain displays of the multifunction display here.
Time
The time, time format (12 or 24 hour indicator) and the changeover between summer/winter time can be set here.
18
Operation
Winter tyres
Here, you can set the speed at which an audible signal should sound. This function is, for example, used for winter tyres where the maximum permissible speed
is lower than the maximum speed of the vehicle.
The following is shown on the information display if this speed is exceeded:
Winter tyres: maximum ... km/h.
Units of measurement
The units for the temperature, consumption and distance driven can be set here.
Alt. speed dis.
Display of the second speed in mph1) can be activated here.
Service
The days and kilometres remaining until the next service can be displayed here.
Factory setting
The display can be restored to its factory settings here.
Door, boot lid and bonnet warning
First read and observe the introductory information and safety warnings on page 18.
If at least one door is open, or the boot or bonnet is open, the MAXI DOT display
shows the vehicle with the corresponding door or boot/bonnet open.
An audible signal also sounds if the vehicle is travelling at more than 6 km/h.
Auto Check Control
First read and observe the introductory information and safety warnings on page 18.
Vehicle condition
Certain functions and conditions of individual vehicle systems are checked continuously when the ignition is switched on and also while driving.
Some error messages and other information are displayed in the MAXI DOT display. The messages are displayed simultaneously with the icons in the MAXI DOT
display or with the warning lights in the instrument cluster » page 20.
The Vehicle status menu item is shown in the main menu of the MAXI DOT display whenever at least one fault message is present. The first of the fault messages is displayed after this menu item is selected. Several error messages are
shown on the display under the message e.g. 1/3. This indicates that the first of a
total of three error messages is being displayed.
As long as the operational faults are not rectified, the symbols are always indicated again. After they are displayed for the first time, the symbols continue to be
indicated without any extra messages for the driver.
Warning symbols
Clutches in the automatic gearbox are too hot
The symbol in the MAXI DOT display indicates that the temperature of the automatic gearbox clutches is too high.
The following message is shown in the MAXI DOT display.
Gearbox overheating. Stop. Read manual.
Stop the vehicle, switch off the engine, and wait until the icon goes out – there
is a risk of gearbox damage. You can continue your journey as soon as the icon
disappears.
Engine oil pressure too low » page 21
Clutches in the automatic gearbox are too
hot
Check engine oil level,
engine oil sensor defective
» page 19
» page 21
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from the traffic, switch off the engine and switch on the hazard warning lights
system » page 45.
1)
On models on which the speedometer indicates mph, the second speed is displayed in km/h.
Instruments and Indicator Lights
19
Note
■
Warning messages shown in the MAXI DOT display must be confirmed with but-
ton B » Fig. 7 on page 18 to call up the main menu.
■
As long as the operational faults are not rectified, the symbols are always indicated again. After they are displayed for the first time, the symbols continue to be
indicated without any extra messages for the driver.
Warning lights
Introduction
This chapter contains information on the following subjects:
Handbrake 20
Brake system 20
Seat belt warning light 21
Alternator
Door open
Engine oil 21
Coolant 22
Power steering 23
Electronic Stability Control (ESC)
Traction Control System (ASR)
Anti-lock brake system (ABS) 24
Rear fog light 24
Bulb failure 24
Exhaust inspection system
Glow plug system (diesel engine)
ECU fault light (petrol engine) 25
Diesel particulate filter (diesel engine)
Fuel reserve
Airbag system
Tyre pressures
Windscreen washer fluid level 26
Traction control (TCS) switched off
Turn signal system
Low beam
Fog lights 27
Cruise control system
Selector lever lock 27
Main beam
The warning lights show certain functions/faults and may be accompanied by audible signals.
WARNING
■
If illuminated warning lights and the corresponding descriptions and warning notes are not observed, this may result in severe injuries or major vehicle
damage.
■
The engine compartment of your car is a hazardous area. There is a risk of
injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is essential to observe safety notes » page 159, Engine compartment.
21
21
23
23
24
24
25
25
26
26
26
26
27
Handbrake
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on if the handbrake is applied. An audible warning is
also given if you drive the vehicle for at least 3 seconds at a speed of more than
6 km/h.
The following message is shown in the MAXI DOT display.
Release parking brake!
Brake system
First read and observe the introductory information and safety warnings on page 20.
The indicator light comes on if the brake fluid level in the braking system is too
low or there is a fault in the ABS.
The following message is shown in the MAXI DOT display.
Brake fluid: Read manual.
27
27
20
Operation
Stop the vehicle, switch off the engine, and check the level of the brake fluid » page 167.
Further information » page 98, Brakes.
WARNING
■
If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning
light system » page 45.
■
The following guidelines should be observed when opening the bonnet and
checking the brake fluid level » page 159, Engine compartment.
■
If the warning light is displayed simultaneously with warning light
» page 24, Anti-lock brake system (ABS), do not continue your jour-
ney! Seek help from a specialist garage.
■
A fault to the ABS system or the braking system can increase the vehicle's
braking distance – there is a risk of accident.
Seat belt warning light
First read and observe the introductory information and safety warnings on page 20.
The indicator light comes on after the ignition is switched on as a reminder for
the driver and front passenger to fasten their seat belt. The indicator light only
goes out once the driver and front passenger have fastened their seat belt.
A steady warning signal sounds at vehicle speeds greater than 20 km/h and the
flashes if the driver and front passenger have not fastened their seat belts.
The warning signal is switched of and the indicator light is permanently lit if the
driver and front passenger have not fastened their seat belts within the next
90 seconds.
Further information » page 127.
Alternator
First read and observe the introductory information and safety warnings on page 20.
If the warning light lights up when the engine is running, the vehicle battery is
not being charged.
Seek help from a specialist garage. The electrical system requires checking.
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from the traffic, switch off the engine and switch on the hazard warning lights
system » page 45.
CAUTION
Do not continue driving if the warning light (coolant system fault) lights up
in addition to the warning light while you are driving. Stop the engine - there is
a risk of engine damage.
Door open
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on if one or several doors are opened or if the boot lid
is opened.
The warning light comes on even when the ignition is switched off. The warning
light lights up for a maximum of 5 minutes.
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from the traffic, switch off the engine and switch on the hazard warning lights
system » page 45.
The warning light lights up red (low oil pressure)
The following message is shown in the MAXI DOT display.
Engine oil
First read and observe the introductory information and safety warnings on page 20.
Oil pressure: Engine off. Read manual.
Instruments and Indicator Lights
21
The warning light comes on for a few seconds when the ignition is switched
on1).
Stop the vehicle, switch off the engine, and check the engine oil level » page 164.
Even if the oil level is correct, do not drive any further if the warning light is
flashing. Also do not leave the engine running at an idling speed.
Seek help from a specialist garage.
The warning light lights up yellow (oil quantity too low)
The following message is shown in the MAXI DOT display.
Check oil level!
Stop the vehicle, switch off the engine, and check the engine oil level » page 164.
An audible signal sounds as a warning signal.
The warning light will go out if the bonnet is left open for more than 30 seconds.
If no engine oil has been replenished, the warning light will come on again after
driving about 100 km.
The warning light flashes yellow (engine oil level sensor faulty)
The following message is shown in the MAXI DOT display.
Oil sensor workshop!
If the engine oil level sensor is faulty, the warning light flashes several times
and an audible signal sounds when the ignition is turned on.
Seek help from a specialist garage.
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from the traffic, switch off the engine and switch on the hazard warning lights
system » page 45.
CAUTION
The red oil pressure light
check the oil level at regular intervals, preferably after every refuelling stop.
is not an oil level indicator! One should therefore
Coolant
First read and observe the introductory information and safety warnings on page 20.
The indicator light remains lit until the engine reaches operating temperature2).
Avoid high speeds, full throttle and high engine loads.
If the warning light lights up or flashes, either the coolant temperature is too
high or the coolant level is too low.
An audible signal sounds as a warning tone.
The following message is shown in the MAXI DOT display.
Check coolant. Read manual.
Stop the vehicle, switch off the engine, check the level of the coolant » page 166,
and refill the coolant if necessary » page 167.
If the coolant is within the specified range, the increased temperature may be
caused by an operating problem at the radiator fan. Check the fuse for the radiator fan, replace if necessary » page 193, Fuses in the engine compartment.
Do not continue driving if the warning light does not go off even though the
coolant level is correct and the fuse for the fan is in working order!
Seek help from a specialist garage.
WARNING
■
If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning
light system » page 45.
■
Carefully open the coolant expansion bottle. If the engine is hot, the cooling
system is pressurized - risk of scalding! It is therefore best to allow the engine
to cool down before removing the cap.
■
Do not touch the radiator fan. The radiator fan may switch itself on automatically even if the ignition is off.
1)
The warning light does not light up in vehicles fitted with the MAXI DOT display when the ignition
is switched on, but only if there is a fault or the engine oil level is too low.
2)
Not on vehicles with the MAXI DOT display.
22
Operation
Power steering
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on for a few seconds when the ignition is switched
on.
If the warning light after switching on the ignition or when driving lights up continuously, a fault exists in the electrohydraulic power steering. The power steering operates with reduced steering assist or does not function at all.
Seek help from a specialist garage.
Further information » page 95.
Seek help from a specialist garage.
The ESC system cannot be turned off, the » page 111 button only switches the
TCS off, the warning light in the instrument cluster lights up.
As the ESC operates in conjunction with the ABS, the ESP indicator light will also
come on if the ABS system fails.
Further information » page 110, Electronic Stability Control (ESC).
Note
The warning light comes on after the ignition is switched on if the vehicle's
battery has been disconnected and reconnected. The warning light should go out
after the vehicle has driven a short distance.
Note
■
If the yellow warning light goes out after starting the engine again and driv-
ing a short distance, it is not necessary to visit a specialist garage.
■
If the vehicle battery has been disconnected and reconnected, the yellow warning light comes on after switching on the ignition. The warning light should go
out after driving a short distance.
■
There is no power-assisted steering support when the vehicle is being towed
without the engine running or when the power-assisted steering is defect. The
vehicle is fully steerable however. There is however increased force required to
turn the steering wheel.
Electronic Stability Control (ESC)
First read and observe the introductory information and safety warn-
on page 20.
ings
The warning light flashes to show that the ESC is currently operating.
If the warning light comes on immediately after you start the engine, the ESC
might be switched off due to technical reasons. Switch the ignition off and on
again. The ESC is fully functional again if the warning light does not light up
after you switch the engine back on.
There is a fault in the ESC system if the warning light lights up.
The following message is shown in the MAXI DOT display.
Fault: Electronic Stability Control (ESC)
Traction Control System (ASR)
First read and observe the introductory information and safety warnings on page 20.
The warning light flashes to show that the ASR is currently operating.
If the warning light comes on immediately after starting the engine, the ASR
can be switched off for technical reasons. Switch the ignition off and on again.
The TCS is fully functional again if the warning light does not light up after you
switch the engine back on.
If the warning light lights up, there is a fault in the ASR.
The following message is shown in the MAXI DOT display.
Fault: Traction control (TCS)
Seek help from a specialist garage.
The fact that the TCS system operates together with the ABS means that the TCS
warning light will also come on if the ABS system is not operating properly.
Further information » page 111, Traction Control System (ASR).
Note
warning light comes on after the ignition is switched on if the vehicle's
The
battery has been disconnected and reconnected. The warning light should go out
after the vehicle has driven a short distance.
Instruments and Indicator Lights
23
Anti-lock brake system (ABS)
First read and observe the introductory information and safety warnings on page 20.
If the warning light lights up, there is a fault in the ABS.
The following message is shown in the MAXI DOT display.
Fault: ABS
The vehicle will only be braked by the normal brake system without the ABS.
Seek help from a specialist garage.
WARNING
■
If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 45.
■
If the warning light » page 20 is displayed simultaneously with the ABS
warning light , do not continue your journey! Seek help from a specialist
garage.
■
A fault to the ABS system or the braking system can increase the vehicle's
braking distance – there is a risk of accident.
Rear fog light
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on when the rear fog lights are operating » page 44.
Bulb failure
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on if a bulb is faulty:
within a few seconds of the ignition being switched on;
›
when a light with a defective bulb is switched on.
›
The following message may be shown in the MAXI DOT display, for example.
INFORMATION Check front right low beam!
Note
The rear side lights and the licence plate lighting have several light bulbs. The indicator light only lights up if all light bulbs of the licence plate lighting or the
parking light (in one rear light) are defective. For this reason, regular check that
these light bulbs are working correctly.
Exhaust inspection system
First read and observe the introductory information and safety warnings on page 20.
If the warning light lights up, there is a fault in the exhaust inspection system.
The engine control unit allows the vehicle to run in emergency mode.
Seek help from a specialist garage.
Glow plug system (diesel engine)
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on after the ignition has been switched on. The engine can be started immediately after the pre-glow warning light goes out.
There is a fault in the glow plug system if the warning light does not come on
at all or lights up continuously.
If the warning light begins to flash while driving, a fault exists in the engine
control. The engine control unit allows the vehicle to run in emergency mode.
Seek help from a specialist garage.
24
Operation
ECU fault light (petrol engine)
First read and observe the introductory information and safety warnings on page 20.
If the warning light comes on or begins to flash while driving, a fault exists in
the engine control unit. The engine control unit allows the vehicle to run in emergency mode.
Seek help from a specialist garage.
Diesel particulate filter (diesel engine)
First read and observe the introductory information and safety warnings on page 20.
The diesel particulate filter separates the soot particles from the exhaust. The
soot particles collect in the diesel particulate filter where they are burnt on a regular basis.
The warning light comes on if soot has accumulated in the filter.
In order to clean the filter, and where traffic conditions permit »
should be driven for at least 15 minutes or until the warning light goes out at an
steady speed of at least 60 km/h at engine speeds of 1800 - 2500 rpm with 4th
or 5th gear engaged (automatic gearbox: position S).
The warning light only goes out once the diesel particulate filter has been
successfully cleaned.
If the filter is not properly cleaned, the warning light does not go out and the
warning light begins to flash.
The following message is shown in the MAXI DOT display.
Diesel particulate filter: Read manual.
The engine control unit allows the vehicle to run in emergency mode. After
switching the ignition off and on again the indicator light, the indicator light
also lights up.
Seek help from a specialist garage.
, the vehicle
WARNING
■
The diesel particle filter achieves very high temperatures. Therefore do not
park in areas where the hot filter can come into direct contact with dry grass
or other combustible materials – there is the risk of fire.
■
Always adjust your speed to suit weather, road, region and traffic conditions. The recommendations indicated by the warning light must not tempt
you to disregard the national regulations for road traffic.
CAUTION
As long as the warning light lights up, one must take into account an increased fuel consumption and in certain circumstances a power reduction of the
engine.
Note
■
We recommend avoiding regularly driving short distances to assist the combus-
tion process of the soot particles in the filter.
■
Using diesel fuel with an increased sulphur content can considerably reduce the
service life of the filter. A ŠKODA Service Partner will be able to tell you which
countries use diesel fuel with a high sulphur content.
■
If the engine is turned off during the filter cleaning process or shortly after-
wards, the cooling fan may turn on automatically for a few minutes.
Fuel reserve
First read and observe the introductory information and safety warnings on page 20.
The indicator light will come on if the fuel level is less than 7 litres.
An audible signal sounds as a warning signal.
The following message is shown in the MAXI DOT display.
Please refuel. Range: ... km
Note
The text in the MAXI DOT display only goes out after the vehicle has been refuelled and driven a short distance.
Instruments and Indicator Lights
25
Airbag system
First read and observe the introductory information and safety warnings on page 20.
If the warning light lights up, there is a fault in the airbag system.
The following message is shown in the MAXI DOT display.
Fault: Airbag
The operational capability of the airbag system is monitored electronically, even if
one of the airbags is switched off.
If a front, side or head airbag or belt tensioner has been switched off using the
vehicle system tester:
The warning light comes on for around 4 seconds after the ignition is switch-
›
ed on and then flashes for approximately another 12 seconds at 2 second intervals.
The following message is shown in the MAXI DOT display.
Airbag/belt tensioner deactivated.
If the front passenger's front airbag was switched off using the key-operated
switch on the side of the dash panel on the passenger side:
The warning light comes on for around 4 seconds after the ignition has been
›
switched on.
switching off the airbag is indicated in the middle of the dash panel by the light-
›
ing up of the yellow indicator light in display
» page 137.
WARNING
If there is a fault, have the airbag system checked immediately by a specialist
garage. Otherwise, there is a risk of the airbag not being activated in the
event of an accident.
The warning light coming on indicates a fault in the system.
Seek help from a specialist garage.
Further information » page 175, Tyre pressure monitor.
Note
If the battery has been disconnected, the warning light illuminates after the ignition is switched on. The warning light should go out after driving a short distance.
Windscreen washer fluid level
First read and observe the introductory information and safety warnings on page 20.
If the windscreen washer fluid level is too low, the warning light comes on.
The following message is shown in the MAXI DOT display.
Top up wash fluid!
Top up with liquid » page 162.
Traction control (TCS) switched off
First read and observe the introductory information and safety warnings on page 20.
The ASR is switched off by pressing the button » page 111 and the warning light
illuminates.
The following message is shown in the MAXI DOT display.
Traction control (ASR) deactivated.
Tyre pressures
First read and observe the introductory information and safety warnings on page 20.
The warning light lights up, if there is a substantial drop in inflation pressure in
one of the tyres. Check and adjust the pressure in all tyres.
26
Operation
Turn signal system
First read and observe the introductory information and safety warnings on page 20.
Either the left or right warning light flashes depending on the position of the
turn signal lever.
If a turn signal light fails, the warning light flashes at twice its normal rate.
Switching off the hazard warning light system is switched on will cause all of the
turn signal lights as well as both warning lights to flash.
Further information » page 43, Turn signal and main beam lights.
Low beam
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on when low beam is selected » page 41.
Fog lights
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on when the fog lights are operating » page 44.
Cruise control system
First read and observe the introductory information and safety warnings
The warning light comes on when the cruise control is operating » page 113.
Selector lever lock
If the warning light lights up, operate the brake pedal. This is necessary to be
able to move the selector lever from position P or N » page 101.
on page 20.
First read and observe the introductory information and safety warnings on page 20.
Main beam
First read and observe the introductory information and safety warnings on page 20.
The warning light comes on when the main beam or headlight flasher are selected » page 43.
Instruments and Indicator Lights
27
Loading...