Skoda Octavia 2012 User Manual

SIMPLY CLEVER

ŠKODA Octavia Owner's Manual

Layout of this Owner's Manual (explanations)

This Owner's Manual has been systematically designed to make it easy for you to search for and obtain the information you require.

Chapters, table of contents and subject index

The text of the Owner's manual is divided into relatively short sections which are combined into easy-to-read chapters. The chapter you are reading at any particular moment is always specified on the bottom right of the page.

The Table of contents is arranged according to the chapters and the detailed Sub- ject index at the end of the Owner's Manual helps you to rapidly find the information you are looking for.

Direction indications

All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of travel of the vehicle.

Units of measurement

All values are expressed in metric units.

Explanation of symbols

 Denotes a reference to a section with important information and safety

advice in a chapter.

 Denotes the end of a section.

 Denotes the continuation of a section on the next page.

 Indicates situations where the vehicle must be stopped as soon as possi-

ble.

® Denotes a registered trademark.

Notes

WARNING

The most important notes are marked with the heading WARNING. These WARNING notes draw your attention to a serious risk of accident or injury.

For the sake of the environment

An Environmental note draws your attention to environmental protection aspects. This is where you will, for example, find tips aimed at reducing your fuel consumption.

Note

A normal Note draws your attention to important information about the operation of your vehicle.

CAUTION

Caution note draws your attention to the possibility of damage to your vehicle

A (e.g. damage to gearbox), or points out general risks of an accident.

Preface

Does not apply to Russia

You have opted for a ŠKODA – our sincere thanks for your confidence in us.

You have received a vehicle with the latest technology and range of amenities. Please read this Owner's Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use of the vehicle.

If you have any questions about your vehicle, please contact a ŠKODA Partner. We wish you much pleasure with your ŠKODA and pleasant motoring at all times. Your ŠKODA AUTO a.s. (hereinafter referred to as ŠKODA)



The on-board literature

The on-board literature for your vehicle consists of this “Owner's Manual” as well as a “Service schedule” and the “Help on the road” brochure.

Depending on the vehicle model and equipment, other additional operating manuals and instructions may be provided (e.g. an operating manual for the Infotainment Radio).

If one of the publications listed above is missing, please contact a ŠKODA Partner.

The Owner's Manual

These operating instructions describe all possible equipment variants without identifying them as special equipment, model variants or market-dependent equipment.

Consequently, this vehicle does not need to contain all of the equipment compo- nents described in this Owner's manual.

The level of equipment of your vehicle refers to your purchase contract of the vehicle. For more information, contact your local ŠKODA retailer.

This owner's manual describes a wide range of electronic functions and systems. Information about how to configure these electronic functions and systems can be found in the operating instructions to Infotainment Radio and/or the Infotainment navigation system.

The illustrations can differ in minor details from your vehicle; they are only intended for general information.

The Service Plan:

includes vehicle data including information on service work performed;

›

is a record of services provided;

›

is provided for entries relating to the mobility warranty (valid only for some

›

countries); serves as warranty certificate of the ŠKODA dealer.

›

The service records are one of the conditions for warranty claims. Please always present the Service schedule when you take your car to a ŠKODA

specialist garage. If the Service Schedule is missing or worn, please contact the ŠKODA specialist

garage that regularly services your car. You will receive a duplicate, in which the previously carried out service work is confirmed by the ŠKODA specialist garage.

The Help on the Road brochure

The brochure contains the important emergency telephone numbers as well as telephone numbers and contact addresses of ŠKODA Partners in different countries.

Table of Contents

Abbreviations

Using the system

Cockpit 7

Overview 6

Instruments and warning lights 9

Instrument cluster 9 Warning lights 12

Information system

Introductory information 21 Outside temperature Recommended gear Door, boot lid and bonnet warning 21 Eco tips Driving data (Multifunction display) 22 Information display Traffic sign recognition Fatigue detection (break recommendation) 27

Unlocking and locking

Vehicle key 28 Child safety lock Open door and close Central locking system 29 Locking/unlocking with the key Vehicle locking/unlocking from the inside 32 Remote control KESSY system Anti-theft alarm system 35 Emergency unlocking/locking Luggage compartment lid 37 Electrical power windows Power panoramic sliding/sliding tilting roof

Lights and visibility 43

Lights 43 Interior light 51 Visibility 52 Windscreen wipers and washers 53 Rear mirror 56

Seats and Stowage 59

Front seats 59 Seat heaters 62 Head restraints 63 Rear seats 63 Boot 64 Roof rack system 68 Cup holder

Ashtray Cigarette lighter 70

Sockets

Storage compartments 72 Clothes hooks

Parking ticket holder

Heating and air conditioning system 81

Heating and air conditioning system Air outlets 82 Heating

Air conditioning system (manual air conditioning system)

Climatronic (automatic air conditioning

system) 86 Auxiliary heating (auxiliary heating and

ventilation)

Starting-off and Driving 92

Starting and stopping the engine

KESSY system 95 Brakes

Shifting Pedals 99

Driving and the Environment 100

Running in 100 Catalytic converter 100 Economical and environmentally friendly

driving 101 Environmental compatibility 103 Driving abroad 104 Driving through water on the street 104

Towing a trailer 106

Towing device 106 Loading a trailer 109 Driving with a trailer 110

Assist systems 112

Brake assist systems

Parking aid Park Assist 116

Cruise control system (CCS) START/STOP 121

Select driving mode

ProActive passenger protection Lane Assist 126

Automatic gearbox

Automatic transmission 129

Communication

Introductory information

Declaration of conformity Warning statement Phonebox 135

Multimedia

Safety

Passive Safety

General information 138

Correct seated position

112 114

119

124 125

129

134 134 134 134

135

138

139

Table of Contents

Seat belts 142

Airbag system 146

Description of the airbag system 146 Front airbags 147 Driver’s knee airbag 148 Side airbags 149 Head airbags 150 Deactivating airbags 151

Passenger protection system 153

Introductory information 153 Activating the system 153

Transporting children safely 154

Child seat

154

Jump-starting 195 Towing the vehicle 196

Fuses and light bulbs 199

Fuses 199 Bulbs 202

Technical data

Introductory information 207 Vehicle identification data 207 Dimensions 208 Specifications and engine oil capacity 209 Vehicle-specific information depending on

engine type

207

210

General Maintenance

Taking care of and cleaning the vehicle

Taking care of your vehicle 159 Accessories, changes and replacement of

parts 165

Inspecting and replenishing

Fuel Engine compartment 169 Vehicle battery

Wheels 181

Tyres and wheel rims

159

167 167

176

181

Do-it-yourself

First-aid kit and warning triangle 188 Fire extinguisher Vehicle tool kit 188 Changing a wheel Tyre repair

Table of Contents

188

189

192

Index

Abbreviations

Abbreviation Definition

rpm Engine revolutions per minute ABS Anti-lock brake system TCS Traction control

CO2 in g/km discharged quantity of carbon dioxide in grams per driven kilo-

metre DPF Diesel particle filter DSG Automatic double clutch gearbox DSR Active driver-steering recommendation EDL Electronic differential lock EPC EPC fault light ESC Electronic Stability Control HBA Hydraulic brake assist HHC Uphill start assist

kW Kilowatt, measuring unit for the engine output MG Manual gearbox

N1 Panel van intended exclusively or mainly for the transporta-

tion of goods

Nm Newton meter, measuring unit for the engine torque

TDI CR Diesel engine with turbocharging and common rail injection

system TSA Trailer stabilisation

TSI Petrol engine with turbocharging and direct injection



Abbreviations

Fig. 1

Using the system

Cockpit

Using the system

Cockpit

Overview

Electrical power windows 38

Door opening lever on the driver's side 29

Electric exterior mirror adjustment 58

Air outlet vent on the driver's side 82

Operating lever:

Turn signal light, headlight and parking light, headlight flasher 45

›

Speed regulating system 119

›

Steering wheel:

With horn

›

With driver’s front airbag

›

With pushbuttons for radio, navigation system and mobile

›

phone

Instrument cluster: Instruments and warning lights

Operating lever:

Multifunction display

›

Windscreen wiper and wash system 53

›

Air outlet vents, middle

Depending on equipment fitted:

Infotainment Radio » operating instructions for Infotainment

›

Radio Infotainment Navigation » operating instructions for the Info-

›

tainment Navigation

Warning light for the deactivated front seat passenger airbag

Switch for hazard warning lights 49

Interior rear-view mirror

Storage compartment on the front passenger side 73

Front passenger airbag

CD/DVD/Blu-ray drive and memory card slot (in the passenger-side storage compartment) » operating instructions for Infotainment

Radio and/or Infotainment Navigation

147

134

151

147

Air outlet vent on the front passenger side 82

Key switch for switching off the front passenger airbag (in front passenger storage compartment) 151

Door opening lever on the front passenger side 29

Electric power-operated window front passenger side 40

Light switch 44

Fuse box (behind the storage compartment in the dash panel) 200

Bonnet release lever 171

Lever for adjusting the steering wheel 93

Ignition lock 94

Pedals 99

Storage compartment 74

Handbrake lever 98

Depending on equipment fitted:

Gearshift lever (manual gearbox)

›

Selector lever (automatic gearbox) 130

›

Depending on equipment fitted:

Operating controls for the heating

›

Operating controls for the air conditioning system 84

›

Operating controls for Climatronic

›

Depending on equipment fitted:

12-Volt power socket

›

Cigarette lighter 70

›

Bar with keys depending on the equipment fitted:



Central locking system 32

›



START STOP 121

›

Traction control TCS



›



Electronic Stability Control ESC 112

›



Selection of driving mode

›

Park Assist



›



Parking aid

›



Tyre inflation pressure calibration

›

Depending on equipment fitted:

USB/AUX input

›

MEDIA IN input

›

113

124

116 114

185

134 134



Cockpit

Note

The arrangement of the controls and switches and the location of some items on right-hand drive models may differ from that shown in » Fig. 1. The symbols on the controls and switches are the same as for left-hand drive models.



Using the system

Instruments and warning lights

Instrument cluster

Introduction



This chapter contains information on the following subjects: Overview

Engine revolutions counter 10 Speedometer 10 Coolant temperature gauge display 10 Fuel gauge display 10 Counter for distance driven 11 Setting the time Display the charge level of the vehicle battery 11 Service Interval Display

WARNING

■

Concentrate fully at all times on your driving! As the driver you are fully re-

sponsible for the operation of your vehicle.

■

Never operate the button in the instrument cluster while driving, only when

the vehicle is stationary!

Overview

Fig. 2 Instrument cluster



Revolutions counter with warning lights » page 10

Display:

With counter for distance driven » page 11

›

With service interval display » page 11



›

With digital clock » page 11

›

With multifunction display » page 22

›

With information display » page 25

›

with warning lights » page 12

›

Speedometer1) with warning lights » page 10

Coolant temperature gauge » page 10

Bar with warning lights » page 12

Button for:

Set hours/minutes

›

Service intervals display – Display of the number of days and kilometres

›

remaining until the next Service event Resetting Service Interval Display

›

First read and observe the introductory information and safety warnings on page 9.



During the journey, the speed can be displayed in a different unit (mph or km/h) in addition to the tachometer display.

Instruments and warning lights

Reset trip counter for the distance driven

›

Charge level indicator

›

Fuel gauge » page 10

Fault display

If there is a fault in the instrument cluster, the following message will appear in the display:

Error: Instrument cluster. Workshop!

INSTRUMENTCLUSTER_WORKSHOP

Ensure the fault is rectified as soon as possible by ŠKODA a specialist garage.

Engine revolutions counter

First read and observe the introductory information and safety warnings on page 9.



The red scale of the rev counter 1 » Fig. 2 on page 9 indicates the range in which the system begins to limit the engine speed. The system automatically restricts the engine speed to a steady limit.

You should shift into the next higher gear before the red scale of the revolution counter is reached, or select mode D on the automatic gearbox.

Follow the recommended gear to prevent engine speeds that are too high or too low » page 21.

For the sake of the environment

Shifting to a higher gear in good time helps to lower fuel consumption, minimises operating noise levels, protects the environment and contributes to a longer life and reliability of the engine.

Speedometer

First read and observe the introductory information and safety warnings on page 9.



Warning against excessive speeds

An audible warning signal will sound when the vehicle speed exceeds 120 km/h1). The audible warning signal is switched off when the vehicle speed falls below this speed limit.

Coolant temperature gauge display

First read and observe the introductory information and safety warnings on page 9.



The coolant temperature gauge 4 » Fig. 2 on page 9 operates only when the ig-



nition is switched on. The following guidelines regarding the temperature ranges must be observed to

avoid any damage to the engine:

Cold range

If the pointer is still in the left area of the scale it means that the engine has not yet reached its operating temperature. Avoid high speeds, full throttle and high engine loads.

The operating range

The engine has reached its operating temperature as soon as the pointer moves into the mid-range of the scale, for a normal style of driving. The pointer may also move further to the right at high engine loads and high outside temperatures.

CAUTION

Additional headlights and other attached components in front of the fresh air inlet impair the cooling efficiency of the coolant. There is then a risk of the engine overheating at high outside temperatures and high engine loads » page 15.



Fuel gauge display

First read and observe the introductory information and safety warnings on page 9.



The fuel gauge 7 » Fig. 2 on page 9 only operates when the ignition is switched on.





This function only applies to certain countries.

Using the system

The fuel tank has a capacity of about 50 litres. The warning light lights up when the pointer reaches the reserve marking» page 18.

CAUTION

Never drive until the fuel tank is completely empty! An irregular supply of fuel can lead to irregular engine running. Unburnt fuel may get into the exhaust system and damage the catalytic converter.

Note

The arrow  next to the icon  within the fuel gauge displays the installation location of the fuel filler on the right side of the vehicle.

Counter for distance driven

First read and observe the introductory information and safety warnings on page 9.



Daily trip counter (trip)

The daily trip counter shows the distance driven since the time the counter was last reset - in steps of 100 m.

The daily trip counter can be reset by briefly pressing the button 6 » Fig. 2 on page 9.

Odometer

The odometer indicates the total distance which the vehicle has been driven.

Setting the time

First read and observe the introductory information and safety warnings on page 9.



Press the button 6 » Fig. 2 on page 9 and keep it pressed down until the Time

›

appears. Release the button 6 - the currently set time is displayed.

›

Press the button 6 again and set the hours.

›

Wait around 4 seconds - the system switches to the minutes setting.

›

Press the button 6 again and set the minutes.

›

The time can also be set in the Infotainment » operating instructions for Infotainment, chapter Unit setup.

Display the charge level of the vehicle battery

First read and observe the introductory information and safety warnings on page 9.



Switch off the ignition.

›

Press the button 6 » Fig. 3 on page 22 and keep it pressed down until Battery

›

status/BATTERY appears.

Release the button

›

played in %.



Service Interval Display

First read and observe the introductory information and safety warnings on page 9.



Service message

Before reaching the service interval, the icon  appears in the display after the ignition is switched on, together with the message:

Service in ... km or ... day(s).

SERVICE IN... km OR ... DAYS

The kilometre indicator or the days indicator reduces in steps of 100 km or, where applicable, days until the service due date is reached.



Once the service interval is reached, the icon  appears in the display after the ignition is switched on, together with the message:

Service now!

SERVICE NOW

Displaying the distance and days until the next service interval

Switch on the ignition.

›

Press the button

›

appears. Release the button

›

The icon  appears in the display, together with the message:

Service in ... km or ... day(s).



- the current charge level of the vehicle battery is dis-

» Fig. 2 on page 9 and keep it pressed down until Service





Instruments and warning lights

SERVICE IN... km OR ... DAYS

Resetting Service Interval Display

After resetting the display with flexible service intervals, the displayed data is the same as that for a vehicle with fixed service intervals. We therefore recommend that the Service Interval Display is only reset by a ŠKODA Partner, who will reset the display with a vehicle system tester.

The ŠKODA Partner:

Resets the memory of the display after the appropriate inspection

›

Adds an entry to the Service Schedule

›

Affixes the sticker with the entry of the following service interval to the side of

›

the dashboard on the driver's side.

It can be reset with the button

Switch off the ignition.

›

Press the button

›

Switch on the ignition.

›

Release the button 6 and press again.

›

and keep it pressed down.

» Fig. 2 on page 9.

CAUTION

We recommend that you do not reset the Service Interval Display yourself as this can result in the incorrect setting of the Service Interval Display, which can also cause possible problems with the operation of your vehicle.

Note

■

Information is retained in the Service Interval Display even after the vehicle bat-

tery is disconnected.

■

If the instrument cluster is exchanged after a repair, the correct values must be entered in the counter for the Service Interval Display. This work is carried out by a ŠKODA specialist garage.

■

For more information on the service intervals » Service Plan.

Warning lights

Auto Check Control

Certain functions and conditions of individual vehicle systems are checked continuously when the ignition is switched on.

Error messages and/or other information are displayed in the instrument cluster display. The messages are displayed at the same time as the symbols in the display and/or the warning lights » page 12.

Depending on the meaning, the icon  or  together with the message appears in the bar with the warning lights 5 » Fig. 2 on page 9.

Symbol Description



While the operational faults remain unrectified, the messages are always indicated again. After they are displayed for the first time, the symbols  or  continue to be indicated without any extra messages for the driver.

WARNING

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49. The warning triangle must be set up at the prescribed distance - observe the national legal provisions when doing so.

Overview



The warning lights show the following functions/faults and may be accompanied by audible signals.

When switching on the ignition, some indicator lights illuminate briefly as a function test. These indicator lights will disappear several seconds after the vehicle is started.

Warning

Danger





Using the system

Symbol Description Reference

  



 







Clutches of the automatic gearbox DSG are too hot

Handbrake » page 14

Brake system » page 14

Seat belt warning light, front » page 14

Seat belt warning light, rear » page 15

Generator » page 15

Coolant temperature/coolant level » page 15

Engine oil » page 15

» page 14



 

Power steering » page 16

Traction control (TCS) » page 16



Traction control (TCS) switched off » page 17



Electronic Stability Control (ESC) » page 17



Antilock brake system (ABS) » page 17



Rear fog light » page 17



Bulb failure » page 17



Exhaust inspection system » page 17



Symbol Description Reference

Glow plug system (diesel engine) » page 18



EPC fault light (petrol engine) » page 18





Diesel particle filter (diesel engine) » page 18

Fuel reserve » page 18



Safety systems » page 19



Tyre pressure » page 19



Windscreen washer fluid level » page 19



Brake pad thickness » page 20





Lane Assist » page 20



 

Turn signal (left/right) » page 20

Trailer turn signal lights » page 20



Fog lights » page 20



Speed regulating system » page 20



Selector lever lock » page 20



Main beam » page 20



Headlight assist » page 20





Instruments and warning lights

Symbol Description Reference

 

START-STOPSystem » page 20

Ice warning » page 20



WARNING

■

Failing to respect active warning lights, their associated descriptions, and

warning messages can lead to major injuries or damage to the vehicle.

■

The engine compartment of your car is a hazardous area. There is a risk of injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is essential to observe safety notes » page 169, Engine compartment.

Clutches of the automatic gearbox DSG are too hot

The warning light  lights up if the temperature of the clutches of the automatic gearbox is too high.

The following message is shown in the information cluster display:

Gearbox overheated. Stop! Owner's manual!

STOP VEHICLE GEARBOX OVERHEAT

Stop the vehicle, switch off the engine, and wait until the light  goes out – risk of gearbox damage! You can continue your journey as soon as the light goes out.



Handbrake 

The warning light  comes on if the handbrake is applied. An acoustic signal will sound if you drive the vehicle above 5 km/h while the handbrake is still on.

The following message is shown in the information cluster display:

Release the handbrake!

RELEASE HANDBRAKE

Brake system 

The warning light  illuminates if the brake fluid level is too low or there is a fault in the ABS.

The following message is shown in the information cluster display:

Brake fluid: owner's manual!

BRAKE FLUID PLEASE CHECK

Stop the vehicle, switch off the engine, and check the level of the brake fluid » page 175 »



WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

■

If the warning light  is displayed simultaneously with warning light

 » page 17, Antilock brake system (ABS) ,  do not continue your jour-

ney! Seek help from a ŠKODA specialist garage.

■

A fault to the braking system can increase the vehicle's braking distance risk of accident!

Seat belt warning light, front

The warning light  comes on after the ignition is switched on as a reminder for



the driver and front passenger to fasten the seat belt. The warning light goes out if the driver or front passenger has fastened their seat

belt. The warning light  flashes and at the same time an acoustic warning signal

sounds when the driver or front passenger has not fastened their seat belt and the speed of the vehicle exceeds 30 km/h.

If the seat belt is not fastened by the driver or front passenger during the next approx. 2 seconds, the warning signal is deactivated and the warning light lights up permanently.

Further information » page 142, Seat belts.











Using the system

Seat belt warning light, rear  

A rear seat belt is not fastened



A rear seat belt is fastened



The warning lights  or  come on after the ignition has been switched on. When the seat belt is fastened/unfastened, the particular warning light lights up

briefly and indicates the current belt status! Further information » page 142, Seat belts.

Dynamo

The warning light  lights up when the engine is running, the vehicle battery is not being charged.

Seek help from a ŠKODA specialist garage to have the electrical system checked out.



WARNING

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

CAUTION

If the warning light  (cooling system fault) comes on in addition to the warning light  when driving, stop the vehicle immediately and switch the engine off – there is a risk of engine damage!

Coolant temperature/coolant level

If the warning light  lights up, this means the coolant temperature is too high. The following message is shown in the information cluster display:

Check coolant! Owner's manual!

ENGINE COOLANT PLEASE CHECK



Stop the vehicle, switch off the engine, check the level of the coolant » page 174,

and refill the coolant if necessary » page 175.

If the coolant is within the specified range, the increased temperature may be

caused by an operating problem at the radiator fan. Check the fuse for the radia-

tor fan, replace if necessary » page 201, Fuses in the engine compartment.

Do not continue driving if the warning light   does not go off even though the

coolant level is correct and the fuse for the fan is in working order!

Seek help from a ŠKODA specialist garage.



WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

■

Carefully open the coolant expansion bottle. If the engine is hot, the cooling system is pressurized – risk of scalding! It is therefore best to allow the engine to cool down before removing the cap.

■

Do not touch the radiator fan. The radiator fan may switch itself on automatically even if the ignition is off.

Engine oil 

The warning light  flashes (low oil pressure)

The following message is shown in the information cluster display:

Oil pressure: Stop! Owner's manual!



STOP VEHICLE OIL PRESSURE

Stop the vehicle, switch off the engine, and check the level of the engine oil » page 172, Checking the engine oil level.

Even if the oil level is correct,  do not drive any further if the warning light is flashing! Also do not leave the engine running at an idling speed.

Seek help from a ŠKODA specialist garage.

The indicator light  lights up (oil quantity too low)

The following message is shown in the information cluster display:

Check oil level!







Instruments and warning lights

CHECK OIL LEVEL

Stop the vehicle, switch off the engine, and check the level of the engine oil » page 172.

The warning light will go out if the bonnet is left open for more than 30 seconds. If no engine oil has been replenished, the warning light will come on again after driving about 100 km.

The indicator light  flashes (engine oil level sensor faulty)

The following message is shown in the information cluster display:

Oil sensor: workshop!

OIL SENSOR WORKSHOP

If the engine oil level sensor is faulty, the warning light flashes  several times and an audible signal sounds when the ignition is turned on.

Seek help from a ŠKODA specialist garage.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

■

Do not continue your journey if for some reason it is not possible  to top up the engine oil under the prevailing conditions! Switch off the engine and seek assistance from a ŠKODA specialist garage.

Power steering  

If the warning light  lights up, this indicates a partial failure of the power steering and the steering forces can be greater. Seek help from a ŠKODA specialist garage.

If the warning light  lights up, this indicates a complete failure of the power steering and the steering assist has failed (significantly higher steering forces). Seek help from a ŠKODA specialist garage.

Further information » page 93.

WARNING

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

Note

If the vehicle's battery has been disconnected and reconnected, the warning light

 comes on after switching on the ignition. The warning light should go out after

driving a short distance. If the yellow warning light  does not go out after starting the engine again and a short drive, it is necessary to visit a ŠKODA specialist garage.

Traction control system (TCS)

If your vehicle is fitted with the ESC system, the ASR is integrated into the ESC system » page 112.

The warning light flashes to show that the ASR is currently operating. If the warning light  lights up, there is a fault in the ASR. If the warning light  comes on immediately after starting the engine, the ASR

can be switched off for technical reasons. Switch the ignition off and on again. If the warning light does not light up after you switch the engine back on, the ASR is fully functional again.



The following message is shown in the information cluster display:

Error: traction control

ASR ERROR

Seek help from a ŠKODA specialist garage. Further information » page 112 and » page 113, Traction control system (TCS).



Note

If the vehicle's battery has been disconnected and reconnected, the warning light

 comes on after switching on the ignition. The warning light should go out after

driving a short distance.



Using the system

Traction control (TCS) switched off

When the warning light  is lit, this means the ASR is switched off.

The following message is shown in the information cluster display:

Traction control (TCS) deactivated.

ASR OFF

Further information » page 113, Traction control system (TCS).

Electronic Stability Control (ESC)

A flashing warning light  shows that the ESC system is currently operating.

If the warning light  lights up, there is a fault in the ESC system.

If the warning light  comes on immediately after starting the engine, the ESC

system can be switched off for technical reasons. Switch the ignition off and on

again. If the warning light does not light up after you switch the engine back on,

the ESC system is fully functional again.

The following message is shown in the information cluster display:

Error: stabilisation control (ESC)

ESC ERROR

Seek help from a ŠKODA specialist garage.

Further information » page 112, Stabilisation Control (ESC).



Note

If the vehicle's battery has been disconnected and reconnected, the warning light

 comes on after switching on the ignition. If the warning light does not go out

after moving a short distance, this means there is an error in the ESC system.

Error: ABS

ABS ERROR

The vehicle will only be braked by the normal brake system without the ABS. Seek help from a ŠKODA specialist garage. Further information » page 113, Antilock brake system (ABS).



WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 49.

■

If the warning light  is displayed simultaneously with warning light ,  do not continue your journey! Seek help from a ŠKODA specialist garage.

■

A fault to the ABS system or the braking system can increase the vehicle's braking distance – risk of accident!

The rear fog light

The warning light  comes on when the rear fog lights are operating » page 48.

Bulb failure

The warning light  comes on if a bulb is faulty:

within 2 seconds of the ignition being switched on;

›

when switching on the defective light bulb.

›

The following message is shown in the information cluster display:

Check right dipped headlight beam!

DIPPED HEADLIGHT CHECK RIGHT







Antilock brake system (ABS)

If the warning light  lights up, there is a fault in the ABS. The following message is shown in the information cluster display:



Exhaust inspection system

If the warning light  lights up, there is a fault in the exhaust inspection system. The engine control unit allows the vehicle to run in emergency mode.



Instruments and warning lights



Seek help from a ŠKODA specialist garage.

Glow plug system  (diesel engine)

The warning light  comes on after the ignition has been switched on. Once the light has gone out, the engine can be started immediately.

There is a fault in the glow plug system if the warning light  does not come on at all or lights up continuously.

If the warning light  begins to flash while driving, a fault exists in the engine control. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a ŠKODA specialist garage.



DIESEL PM FILTER OWNER MANUAL

Seek help from a ŠKODA specialist garage.

WARNING

■

The diesel particle filter achieves very high temperatures. Therefore do not park in areas where the hot filter can come into direct contact with dry grass or other combustible materials – there is the risk of fire!

■

Always adjust your speed to suit weather, road, region and traffic conditions. The recommendations indicated by the warning light must not tempt you to disregard the national regulations for road traffic.





EPC

fault light (petrol engine)

If the warning light control unit allows the vehicle to run in emergency mode.

Seek help from a ŠKODA specialist garage.



lights up, there is a fault in the engine control. The engine

Diesel particulate filter (diesel engine)

The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a regular basis.

If the warning light  lights up, soot has accumulated in the diesel particulate filter.

In order to clean the diesel particulate filter, and where traffic conditions permit »

, the vehicle should be driven at an even speed of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 15 minutes or until the warning light goes out with the 4th or 5th gear engaged (automatic gearbox: position S).

The warning light  goes out after the diesel particulate filter has been successfully cleaned.

If the filter is not properly cleaned, the warning light  does not go out and the warning light  begins to flash.

The following message is shown in the information cluster display:

Diesel particulate filter: owner's manual!

Using the system

CAUTION

As long as the warning light  lights up, one must take into account an increased fuel consumption and in certain circumstances a power reduction of the engine.



Note

■

To assist the combustion process of the soot particles, we recommend that reg-

ularly driving over short distances should be avoided.

■

Using diesel fuel with an increased sulphur content can considerably reduce the life of the diesel particle filter. A ŠKODA specialist garage will be able to tell you which countries use only diesel fuel with high sulphur content.

Fuel reserve

When the warning light  is lit, this means there is a fuel reserve of under around 7 litres left.

An audible signal sounds as a warning signal. The following message is shown in the information cluster display:

Please refuel. Range: ... km

PLEASE REFUEL







Note

The text in the information display goes out after refuelling and driving a short distance.

Safety systems

If the warning light  lights up, there is a fault in the airbag or pedestrian protection system.

Airbag system

The following message is shown in the information cluster display:

Error: airbag

AIRBAG ERROR

The functionality of the airbag system is monitored electronically even if one of the airbags is switched off.

The following applies if one of the airbags or the belt tensioner was switched off with the diagnostic equipment:

The warning light  lights up for approx. 4 seconds after switching on the ignition and then flashes again for approx. 12 seconds.

The following message is shown in the information cluster display:

Airbag/belt tensioner deactivated.

AIRBAG/BELT TENSIONER OFF

The following applies if the front passenger airbag has been switched off using the key switch in the storage compartment:

The indicator light  comes on for around 4 seconds after the ignition has been

›

switched on; The warning light

›

panel lights up after switching on the ignition » page 151.

Passenger protection system

The following message is shown in the information cluster display:

Error: pedestrian protection





in the display

   

in the middle of the dash

PASSENGER PROTECTION SYSTEM ERROR

Further information » page 153.



WARNING

If there is a fault in the safety system, have it checked immediately by a ŠKODA specialist garage. Otherwise, there is a risk of the systems not being activated in the event of an accident.

Tyre pressure

The warning light  lights up, if there is a substantial drop in inflation pressure in one of the tyres. Check and adjust the pressure in all tyres » page 181.

An audible signal sounds as a warning signal. If the warning light  lights up, there is a fault in the system. Seek help from a ŠKODA specialist garage. Further information » page 185, Tyre control display.



Note

If the vehicle's battery has been disconnected and reconnected, the warning light

 comes on after switching on the ignition. If the warning light does not go out

after moving a short distance, this means there is an error in the system. Seek help from a ŠKODA specialist garage.

Windscreen washer fluid level

If the windscreen washer fluid level is too low, the warning light  comes on. Top up with washer fluid.

Top up with liquid » page 176. The following message is shown in the information cluster display:

Top up washer fluid!

WASHER FLUID PLEASE TOP UP





Instruments and warning lights

Brake pad thickness 

If the indicator light  is lit, the brake pads are worn. The following message is shown in the information cluster display:

Check brake wear!

BRAKE PADS PLEASE CHECK

Seek help from a ŠKODA specialist garage.

The trailer must be unhitched properly

Fog lights

The warning light  comes on when the fog lights are operating » page 48.



» page 106, Towing a trailer.

Speed regulating system 



The warning light  comes on when the cruise control is operating » page 119.



Lane Assist 

The warning lights   indicates the state of the Lane Assist system. Further information » page 126.

Turn signal system 

Either the left  or right  indicator light flashes depending on the position of the control lever.

If a turn signal light fails, the warning light flashes at twice its normal rate. This does not apply when towing a trailer.

Switching off the hazard warning light system is switched on will cause all of the turn signal lights as well as both warning lights to flash.

Further information » page 45, Turn signal and main beam light.

Trailer turn signal lights

If the indicator light  flashes, the trailer turn signal lights are activated. If a trailer is hitched and the warning light  is not flashing, one of the trailer turn

signal lights has failed. The following message is shown in the information cluster display:

Trailer: check left turn signal!

TRAILER TURN SIG_ CHECK LEFT

Using the system







Selector lever lock

If the warning light  lights up, operate the brake pedal. This is necessary, to be able to move the selector lever from position P or N » page 131.



Main beam

The warning light  comes on when the main beam or headlight flasher are selected » page 45.

Headlight assist

The warning light  comes on when Headlight assist is operating. Further information » page 47, Headlight assist.



START STOP system 

The warning lights   indicates the state of the START STOP system. Further information » page 121.

Ice warning

The warning light  draws your attention to the risk of ice. Further information » page 21.













Information system

Introductory information

The information system provides the driver with alerts and messages about individual vehicle systems. These alerts and messages appear in the display of the instrument cluster 2 » Fig. 2 on page 9.

The following is displayed in the information system:

The outside temperature » page 21;

›

Recommended gear » page 21;

›

Door, boot lid and bonnet warning » page 21;

›

Eco tips » page 21;

›

Service Interval Display » page 11;

›

Auto Check Control » page 12

›

some warning lights » page 12;

›

Driving data » page 22;

›

Warning against excessive speeds » page 24

›

Data on the information display » page 25;

›

Traffic sign recognition » page 25;

›

Fatigue detection system » page 27;

›

Selector lever positions for an automatic gearbox » page 130;

›

Information and alerts in the Assist systems » page 112.

›

Outside temperature

The current outside temperature is indicated in the display of the instrument cluster.

If the outside temperature drops below +4 °C while driving, a snow flake symbol (warning signal for ice on the road) appears before the temperature indicator and an audible signal will sound.

If the outside temperature is less than +4 °C when the ignition is turned on, a snow flake symbol appears in the display and an acoustic signal sounds. After pressing the rocker switch the function shown last is indicated.

or the adjustment wheel D » Fig. 3 on page 22,

WARNING

Even at temperatures around +4 °C, black ice may still be on the road surface! Do not only rely upon the information given on the outside temperature display that there is no ice on the road.

Recommended gear

In order to minimise the fuel consumption, a recommendation for shifting into another gear is indicated in the display.

Information about the currently-selected gear is shown in the upper part of the display. When the system determines that a change in gear is required, the arrow symbol  and the recommended gear appears next to the current gear indication.

For instance, if    appears in this display, this means it is recommended that you shift from 3rd into 4th gear.

WARNING

The driver is always responsible for selecting the correct gear in different driving situations, such as overtaking.



Door, boot lid and bonnet warning

If at least one door is open, or the boot or bonnet is open, the instrument cluster display indicates the relevant open door or boot/bonnet.

An acoustic signal will also sound if you drive the vehicle above 6 km/h.

Eco tips

To minimise fuel consumption, fuel economy tips can appear in the display. Eco tips are indicated next to the letters ECO-TIP. For instance, if the air-condition is on and a window is open, the following mes-

sage appears ECO TIP Air conditioning switched on: close windows. Eco tips display must be activated in the Infotainment » operating instructions for

Infotainment, chapter Vehicle settings.



Information system

Driving data (Multifunction display)

 Introduction

This chapter contains information on the following subjects: Select data from the multifunction display

Memory 22 Multifunction display details 23 Warning against excessive speeds 24

The multifunction display only operates if the ignition is switched on. After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.

Individual menu items can be shown or hidden » Bedienungsanleitung Infotainment, chapter Setting vehicle systems (CAR button).

WARNING

Concentrate fully at all times on your driving! As the driver you are fully responsible for the operation of your vehicle.

Note

In certain countries the displays appear in the Imperial system of measures.

Select data from the multifunction display

Fig. 3 Buttons (adjustment wheel) on the operating lever/multifunction

steering wheel

First read and observe the introductory information and safety warnings on page 22.



Selecting using the operating lever

Briefly press the rocker switch A » Fig. 3 up or down.

›

Selecting using the multifunction steering wheel

Turn the adjustment wheel D » Fig. 3 upwards or downwards.

›



Memory

First read and observe the introductory information and safety warnings



The multifunction display is equipped with three automatic memories.

Select memory

Press the button B or adjustment wheel D » Fig. 3 on page 22.

›

Resetting

Select the desired memory.

›

Press longer on the button B or adjustment wheel D » Fig. 3 on page 22.

›

The following values of the selected memory are set to zero:

Average fuel consumption

›

Distance driven

›

on page 22.





Using the system

Average speed

›

Driving time

›

Since start

The memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued within 2 hours after switching off the ignition. If the trip is interrupted for more than 2 hours, the memory is automatically erased.

Long-term

The memory gathers driving information from any number of individual journeys up to a total of 99 hours and 59 minutes driving or 9 999 kilometres driven. The memory is deleted when either of these limits is reached and the calculation starts all over again.

Since refuel

The memory gathers driving information since the last refuelling. The memory is erased automatically the next time you fill up.

Note

Disconnecting the vehicle battery will delete all memory data.

Multifunction display details

First read and observe the introductory information and safety warnings



Range

The range indicates the distance you can still drive with your vehicle based on the level of fuel in the tank and the same style of driving as before.

The display is shown in steps of 10 km. After lighting up of the indicator light the display is shown in steps of 5 km.

The fuel consumption over the last 50 km is used to calculate the range. The range can increase if you drive in a more fuel-efficient manner.

on page 22.



Average fuel consumption

The average fuel consumption1) is calculated since the last time the memory was erased » page 22.

If you wish to determine the average fuel consumption over a certain period of time, you must set the memory at the start of the new measurement to zero » Fig. 3 on page 22. After erasing the memory, no fuel consumption data will appear for the first 100 m driven.

The fuel consumption data is updated regularly while you are driving.

Current fuel consumption

You can use this information to adapt your driving style to the desired fuel consumption1).

The display appears in litres/hour if the vehicle is stationary or driving at a low speed2).

Oil temperature

If the engine oil temperature is in the range 80-110 °C, the engine operating temperature is reached.

If the temperature lies below 80 °C or above 110 °C, avoid high engine revs, full throttle and high engine loads.



If the oil temperature is lower than 50 °C or if a fault in the system for checking the oil temperature is present,

Warning against excessive speeds

Setting the speed limit, e.g. for the intra-urban top speed » page 24.

Traffic sign recognition

In the display, up to three detected traffic signs can be displayed, which provide information about the following:

Maximum speed (including additional sign);

›

Overtaking prohibited.

›

Further information » page 25, Traffic sign recognition.

Current driving speed

The current speed is identical to the display on the speedometer page 9.



are displayed instead of the oil temperature.

» Fig. 2 on



To set the units for the fuel consumption display » Bedienungsanleitung Infotainment, chapter Unit setup.

On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is stationary.

Information system

Average speed

The average speed since the memory was last erased is shown in the display in km/hour » page 22. To determine the average speed over a certain period of time, set the memory to zero at the start of the measurement » page 22.

After erasing the memory, no average speed data will appear for approx. the first 300 m driven.

The display is updated regularly while you are driving. The average speed data is updated regularly while you are driving.

Distance travelled

The distance driven since the memory was last erased appears in the display. If you want to measure the distance travelled from a particular moment in time

on, at this moment, reset the memory by setting the button to zero » page 22. The maximum distance indicated in both memories is 9 999 km. The indicator is

automatically set back to zero if this period is exceeded.

Driving time

The driving time which has elapsed since the memory was last erased, appears in the display. If you want to measure the time travelled from a particular moment in time on, at this moment, reset the memory by setting the button to zero » page 22.

The maximum distance indicated in both memories is 99 hours and 59 minutes. The indicator is set back to zero if this period is exceeded.

Convenience consumers

The consumption display for the convenience consumers in l/h. Together with the consumption display, a list of three convenience consumers

with the highest consumption is also displayed.

Warning against excessive speeds

Fig. 4 Buttons (adjustment wheel) on the operating lever/multifunction

steering wheel

First read and observe the introductory information and safety warnings on page 22.



Adjust the speed limit while the vehicle is stationary

With the button A » Fig. 4 or, if applicable, the adjustment wheel D, select the

›

menu item Warning against excessive speeds.

Pressing the button B or the adjustment wheel D activates the setup mode

›

for the speed limit.

Set the desired speed limit, e.g. 50 km/h, with the button A or, if applicable,

›

the adjustment wheel D.

Confirm the speed limit by pressing button B, or adjustment wheel D or wait

›

around 5 seconds. Your settings are saved automatically. This allows you to set the speed in 5 km/h intervals.



Adjusting the speed limit while the vehicle is moving

With the button

›

menu item Warning against excessive speeds.

Drive at the desired speed, e.g. 50 km/h.

›

Press the button B or the adjustment wheel D to accept the current speed as

›

the speed limit (the value flashes). If you wish to change the set speed limit, it is changed in 5 km/h intervals (e.g. the

accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).

Press again the button B or the adjustment wheel D to confirm the speed lim-

›

it, or wait approx. 5 seconds and the setting is saved automatically (the value

stops flashing).

» Fig. 4 or, if applicable, the adjustment wheel D, select the



Using the system

Change or delete speed limit

With the button A » Fig. 4 or, if applicable, the adjustment wheel D, select the

›

menu item Warning against excessive speeds. Pressing the button B or the adjustment wheel D deletes the speed limit.

›

Pressing the button B or the adjustment wheel D again activates change

›

mode for the speed limit.

If the pre-set speed is exceeded, an acoustic signal appears as a warning tone and a warning message appears in the instrument cluster display, e.g.:

Speed 50 exceeded.

SPEED TOO HIGH

The set speed limit value remains stored even after switching off the ignition. After a gap between driving exceeding 2 hours, the pre-set speed limit is deleted.

Information display

Fig. 5

Buttons (adjustment wheel) on the operating lever/multifunction

steering wheel

The information display provides you with information on the current operating state of your vehicle. The information display also provides you with data (de-

pending on the equipment installed in the vehicle) relating to the Infotainment, multi-functional indicator, etc.

Operating with the buttons on the operating lever

Activate the Main menu by pressing the rocker switch

» Fig. 5 for longer.

Individual menu items can be selected by means of the rocker switch the pushbutton B is briefly pressed, the information you have selected is displayed.

Operating the button/adjustment wheel on the multifunction steering wheel

Activate the Main menu by pressing the rocker switch C » Fig. 5 for longer. The individual menus can be selected by pressing the adjustment wheel D. The

selected menu is displayed after briefly pressing the adjustment wheel D. By briefly pressing the C button you will reach one level higher.

Main menu points

The following information can be selected (depending on the equipment installed on the vehicle):

■

Driving data » page 22



■

Assist systems » page 126

■

Navigation » operating instructions for Infotainment, chapter Navigation system (NAV button)

■

Audio » operating instructions for Infotainment, chapter Media (MEDIA button)

■

Telephone » operating instructions for Infotainment, chapter Telephone (PHONE button)

■

Vehicle » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button)

The menu items Audio and Navigation are only displayed when the factory-fitted Infotainment radio or navigation system is switched on.

Note

If warning messages are shown in the information display, these messages must be confirmed with the button B on the operating lever or with the adjustment wheel D on the multifunction steering wheel » Fig. 5 to call up the main menu.

Traffic sign recognition



Introduction

This chapter contains information on the following subjects: Operating principle 26

Information for the driver 27

. When





Information system

The detected traffic signs appear in the instrument cluster display in the following menu:

■

Driving data

■

Traffic sign

Additional display

If the menu item is not currently displayed with traffic sign detection, the traffic sign is displayed with the speed limit in the upper area of the instrument cluster display » Fig. 7 on page 26 - .

The additional display traffic sign detection can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Traffic sign display when towing a trailer

When towing a trailer, displaying the traffic signs which apply when towing a trailer can be activated.

The traffic sign detection display when towing a trailer can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

WARNING

■

Traffic sign detection only operates as a support. Real traffic signs always have priority over electronic displays. The driver is always responsible for correctly assessing the traffic situation.

■

Traffic signs may not be recognised at all by the system, or may be recognised incorrectly. As a result, the traffic signs may not be displayed at all, or the wrong one may appear.

■

Traffic sign recognition does not warn about exceeding the maximum permitted speed nor does it adjust the driving speed to the maximum speed!

■

The display is based on standard national speed units. The display  in the instrument cluster display can therefore be in km/h or mph depending on the country concerned.

Note

Traffic sign recognition is not available in all countries.

Operating principle

Fig. 6

Windscreen: Camera viewing range for traffic sign recognition

Fig. 7

Instrument cluster display: Example of traffic sign recognition display/additional display

First read and observe the introductory information and safety warnings on page 25.



Traffic sign recognition allows traffic signs with maximum speeds/no overtaking recognised by the system to be shown in the instrument cluster display.

Additional signs, such as 'when wet' or signs which only apply for a limited time can also be displayed.

Traffic sign recognition works on the basis of the data captured by the camera and is only able to show traffic signs which are in the camera's viewing range » Fig. 6.

Data from the camera can be supplemented by information from the Infotainment



Navigation. This is the reason why traffic signs with maximum speeds can also be shown on sections of roads which do not have any traffic signs.



Using the system

Traffic sign recognition may not be available or may only be available to a limited

extent in the following situation:

in poor visibility conditions, e.g. fog, heavy rain, thick snowfall;

›

when dazzled by the sun;

›

when dazzled by oncoming traffic;

›

when the camera viewing range is obstructed by an obstacle;

›

at high speeds;

›

when the traffic signs are fully or partially obscured (e.g. by trees, snow, dirt or

›

other vehicles); when the traffic signs are not standard (round with a red border);

›

when the traffic signs are damaged or bent;

›

when the traffic signs are fixed to signs with flashing lights;

›

when the traffic signs were changed and the navigation data are out of date.

›

Information for the driver

First read and observe the introductory information and safety warnings on page 25.



The information for the driver appears in the instrument cluster display.

No traffic signs detected.

No maximum speeds were recognised (e.g. on German motorways where there is

no speed limit).

Error: traffic sign recognition

A system error is present. Seek help from a ŠKODA specialist garage.

Traffic sign recognition: clean windscreen!

The windscreen is dirty, iced over or misted up in the camera viewing range. Clean

the windscreen or remove the obstacles.

Traffic sign recognition: restricted.

Infotainment Navigation is not currently providing any data. Check whether the

maps are up-to-date or the whether the vehicle is currently in a location for which

no navigation data are available.

Fatigue detection (break recommendation)

The fatigue detection system advises the driver on the basis of information about

the steering behaviour, to take a break from driving. The system recommends a

break at speeds of 65-200 km/h.

After the ignition has been switched on, the system evaluates the steering behaviour for 15 minutes. This baseline analysis is constantly compared with the current steering behaviour. If the system detects deviations from normal steering behaviour due to possible fatigue of the driver, it recommends to take a break from driving.

The symbol  appears in the instrument cluster display, with the following message:

Driver alert. Take a break.

DRIVER ALERT TAKE A BREAK



An audible signal is also emitted.

The system deletes the stored baseline analysis if one of the following conditions is met:

the vehicle is stopped and the ignition is turned off,

›

the vehicle is stopped, the seat belt is taken off and the driver's door is opened;

›

the vehicle is stopped for more than 15 minutes.

›

If none of these conditions is met, the system will recommend another break from driving.

The system can be activated/deactivated in the Infotainment » operating instruc- tions for Infotainment, chapter Setting vehicle systems (CAR button).

WARNING

■

For the driving ability is always the driver's responsibility. Never drive if you

feel tired.

■

The system may not detect all cases where a break is needed.

■

Therefore, take regular, sufficient breaks during long trips.

■

There will be no warning during the so-called micro-sleep.



Note

■

In some situations, the system may evaluate the driving incorrectly and thus mistakenly recommend a break (e.g. sporty driving, in adverse weather conditions, or in bad road conditions).

■

The fatigue detection system is designed primarily for motorway driving.



Information system

Unlocking and locking

Vehicle key

Note

Please contact a ŠKODA Partner if you lose a key as they can obtain a new one for you.



Introductory information

Key: without/with remote control

Fig. 8

Two keys are provided with the vehicle. Depending on the equipment, your vehicle can be equipped with keys without radio remote control » Fig. 8 –  or with radio remote control» Fig. 8 – .

WARNING

■

Always withdraw the key whenever you leave the vehicle – even if it is only for a short time. This is particularly important if children are left in the vehicle. The children might otherwise start the engine or operate electrical equipment (e.g. electrical power windows) – risk of injury!

■

Do not withdraw the ignition key from the ignition lock until the vehicle has come to a stop! The steering lock might otherwise engage unintentionally – risk of accident!

CAUTION

■

Each key contains electronic components; therefore it must be protected

against moisture and severe shocks.

■

Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,

etc.) have a negative effect on the functionality of the locking cylinder and ignition lock.

Replacing the battery in the remote control key

Remote control key: Remove cover/remove battery

Fig. 9

Each remote control key contains a battery that is located under the cover

» Fig. 9. If the battery is discharged, the red indicator light B does not flash

after you press a button on the remote control key » Fig. 14 on page 32. We recommend that you ask a ŠKODA Partner to replace the key battery. Howev-

er, if you would like to replace the discharged battery yourself proceed as follows.

Flip out the key.

›

Press off the battery cover with your thumb or using a flat screwdriver in the

›

region of arrows Remove the discharged battery from the key by pressing the battery down-

›

wards in the region of arrow 2. Insert the new battery.

›

Ensure that the “+” symbol on the battery is facing upwards. The correct polarity is shown on the battery cover.

Place the battery cover on the key and press it down until it clicks into place.

›

» Fig. 9.

CAUTION

The replacement battery must have the same specification as the original battery.



Using the system

For the sake of the environment

Dispose of the used battery in accordance with national legal provisions.

Note

The key has to be synchronised if the vehicle cannot be unlocked or locked with

the remote control key after replacing the battery » page 33.

Child safety lock

Open door and close



Fig. 10

Child safety locks on the rear doors

The child safety lock prevents the rear door from being opened from the inside.

The door can only be opened from the outside.

You can switch the child safety lock on and off using the vehicle key.

Switching on

Turn the slot of the safety lock in the direction of the arrow » Fig. 10 (mirror-

›

inverted on the right doors).

Switching off

Turn the slot of the safety lock in the opposite direction to the arrow (mirror-

›

inverted on the right doors).

Fig. 11 Door handle/door opening lever: outside/inside

Opening from the outside

Unlock the vehicle and pull the handle on the door handle A » Fig. 11.

›

Opening from the inside

Pull the handle on the door opening lever B.

›

Closing from the inside

Grab the pull handle C and close the door.

›

WARNING

■

Make sure that the door has closed correctly as it can open suddenly while

driving - danger of death!

■

Only open and close the door when there is no one in the opening/closing

range - risk of injury!

■

An opened door can close automatically if there is a strong wind or the vehi-

cle is on an incline - risk of injury!



Central locking system



Introduction

This chapter contains information on the following subjects: Individual settings

Safe securing system 30

Unlocking and locking





The central locking system allows you to lock and unlock all doors, the fuel filler flap and boot lid at the same time based on the current setting.

Display of the locking

After locking the vehicle, the warning light in the driver's door flashes for around 2 seconds in quick succession, afterwards it begins to flash evenly at longer intervals.

Displaying an error

If the indicator light in the driver's door initially flashes quickly for around 2 seconds, and then lights up for 30 seconds without interruption before flashing again slowly, you will need to seek the assistance of a ŠKODA specialist garage.

WARNING

■

Locked doors prevent unwanted entry into the vehicle from outside, for example at road crossings. Locked doors do, however, make it more difficult for rescuers to get into the vehicle in an emergency – danger to life!

■

If the car is locked and the safe securing system is activated, there must not be any person in the car as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emergency – hazard!

Note

■

The anti-theft alarm system is activated when the vehicle is locked even if the

safe securing system is deactivated. The interior monitor is however not activated.

■

Convenience opening/closing of the windows can be operated when locking/

unlocking the vehicle.

■

In the event of an accident in which the airbags are deployed, the locked doors

are automatically unlocked in order to enable rescuers to gain access to the vehicle.

■

Only the driver's door can be unlocked or locked using the key if the central

locking system fails » page 31. The other doors and the boot lid can be emergency locked or unlocked.

■

Emergency locking of the door » page 36.

■

Emergency unlocking of the luggage compartment lid » page 38.

Individual settings

First read and observe the introductory information and safety warnings on page 29.



Set the following functions » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Opening a single door

This function makes it possible to only unlock the driver's door. The other doors, the fuel filler flap and the boot lid remain locked and are only unlocked after being opened again.

Unlocking a vehicle side door

This function enables you to unlock both doors on the driver's side. The other doors, the fuel filler flap and the boot lid remain locked and are only unlocked after being opened again.

Unlocking the vehicle with the KESSY system

This function enables you to unlock all the doors, individual doors, both doors on the left and right vehicle side or to unlock the driver and front passenger door at the same time. The other doors, the fuel filler flap and the boot lid remain locked and are only unlocked after being opened again.

Automatic locking and unlocking

All doors are locked from a speed of around 15 km/h. The button in the handle of the boot lid is deactivated.

If the ignition key is withdrawn, the car is then automatically unlocked again. In addition, it is possible for the driver or front passenger to unlock the car by pressing the central locking button .

The vehicle doors can be unlocked and opened at any time by pulling once on the door opening lever.

Safe securing system



First read and observe the introductory information and safety warnings on page 29.



The door locks are blocked automatically if the vehicle is locked from the outside. Afterwards, it is not possible to open the doors with the door handle either from the inside or from the outside.





Using the system

If the vehicle is locked and the safe securing system is switched off, the door can

be opened separately from the inside by a single pull on opening lever.

A message is shown after switching off the ignition.

Information message

In the instrument cluster display: CHECK SAFELOCK.

Vehicles with the information display: Check SAFELOCK! Owner's manual! Check

SAFELOCK! Owner's manual!)

Switching on

The safelock switches on automatically the next time the vehicle is locked and

unlocked.

Switching off

The safelock can be switched off by locking twice within 2 seconds.

Switch-on display

The warning light flashes for around 2 seconds in quick succession, afterwards it

begins to flash evenly at longer intervals.

Switch-off display

The indicator light in the driver door flashes for about 2 seconds fast, goes out

and starts to flash at longer intervals after about 30 seconds.

Locking/unlocking with the key

Fig. 12

Turning the key for unlocking and locking the vehicle

Locking

Turn the key in the locking cylinder of the driver's door in the direction of arrow

›

» Fig. 12.

The following is true after unlocking.

The doors, the boot lid and the fuel filler flap are unlocked.

›

The switched on interior lights come on over the door contact.

›

The safe securing system is switched off.

›

The indicator light in the driver door stops flashing.

›

On vehicles with remote control, only the driver's door is unlocked.

The following is true after locking.

The doors, the boot lid and the fuel filler flap are locked.

›

The switched on interior lights go out over the door contact.

›

The safe securing system is switched on.

›

The warning light in the driver door begins flashing.

›

If at least one door has been opened, the vehicle cannot be locked. Turning the key in the driver's lock twice inside 2 seconds in the direction of the

» Fig. 12 switches off the safelock.

arrow



Note

■

The windows open and close as long as the key is kept in the locked/unlocked

position; the sliding/tilting roof is tilted.

■

If the vehicle is equipped with an anti-theft alarm system, you must insert the

key into the ignition lock and switch the ignition on within 15 seconds after unlocking the door in order to deactivate the anti-theft alarm system. The alarm is triggered if the ignition is not switched on within 15 seconds.



Unlocking

Turn the key in the locking cylinder of the driver's door in the direction of arrow

›

» Fig. 12.

Unlocking and locking

Vehicle locking/unlocking from the inside

Remote control

Fig. 13

Central locking button

If the vehicle was not locked from the outside, you can also unlock or lock it with the button » Fig. 13 without the ignition switched on. While a door is opened, the vehicle cannot be locked.

Locking

Press the button  » Fig. 13. The symbol  in the button comes on.

›

Unlocking

Press the button  » Fig. 13. The symbol  in the button is no longer illuminated.

›

The following applies if your vehicle has been locked using the central locking button.

It is not possible to open the doors or the luggage compartment lid from the

›

outside (safety feature, e.g. when stopping at traffic lights etc.). The doors can be unlocked and opened from the inside by a single pull on the

›

opening lever of the respective door. In the event of an accident in which the airbags are deployed, the locked doors

›

are automatically unlocked from the inside in order to enable rescuers to gain access to the vehicle.

WARNING

■

Locked doors make it difficult for rescuers to get into the vehicle in an emergency – hazard!

■

Never leave children unattended in the vehicle.

Introductory information

You can use the remote control key to:

unlock and lock the vehicle,

›

unlocking boot lid;

›

open and close the windows » page 40, Window convenience operation.

›

The transmitter with the battery is housed in the handle of the remote control key. The receiver is located in the interior of the vehicle. The operating range of the remote control key is approx. 30 m. But this range of the remote control can be reduced if the batteries are weak.

The key has a fold-open key bit which can be used for unlocking and locking the car manually and also for starting the engine.

The spare key must by initialised by a ŠKODA partner after the receiver unit is repaired or replaced. Only then can the remote control key be used again.

Note

■

The operation of the remote control may temporarily be affected by interference from transmitters close to the car and which operate in the same frequency range (e.g. mobile phone, TV transmitter).

■

The battery must be replaced if the central locking or anti-theft alarm system does react to the remote control at less than approx. 3 metres away » page 28.

Unlocking/locking

Fig. 14

Remote control key





Note

If the safelock system is switched on central locking buttons do not operate.

Using the system

» page 30, the door opening lever and the





Unlocking the vehicle



Locking the vehicle



Unlocking the boot lid

Folding out/folding up of the key bit

Warning light

Unlocking

The turn signal lights flash twice as confirmation that the vehicle has been unlocked.

If you unlock the vehicle and do not open a door or the boot lid within the next 45 seconds, the vehicle will lock again automatically and the safelock system or anti-theft alarm system will be switched on. This function is intended to prevent the car being unlocked unintentionally.

The seat and mirror are adjusted after the vehicle is unlocked » page 61, Memo- ry function of the power seat.

Locking

The turn signal lights flash once as confirmation that the vehicle has been locked. If the doors or the luggage compartment lid remain open after the vehicle has

been locked, the turn signal lights do not flash until they have been closed. The current position of the seat and mirror after the vehicle is locked » page 61,

Memory function of the remote control key. If the button

press the button  to unlock the vehicle.



is accidentally pressed before the key is inserted into the ignition,

WARNING

If the car is locked from the outside and the safelock system is switched on, there must not be any person in the car as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emergency – hazard!

Synchronization

If the vehicle does not unlock when pressing the remote control, the key may not be synchronised. This can occur when the buttons on the remote control key are actuated a number of times outside of the operative range of the equipment or the battery in the remote control key was replaced.

This means it is necessary to synchronise the key as follows:

press any button on the remote control key;

›

pressing of the button means that the door will unlock with the key within 1 mi-

›

nute.

KESSY system

Introductory information

The KESSY system (Keyless Entry Start Exit System) enables a comfort unlocking and locking of the vehicle and starting the engine without actively using the key » page 92, Starting and stopping the engine. The KESSY system is integrated in the central locking system and all of the functions of the remote control.

Locking/unlocking



Note

■

Only operate the remote control when the doors and luggage compartment lid

are closed and the vehicle is in your line of sight.

■

If the driver door is open, the vehicle cannot be locked using the remote control

key.

Fig. 15

KESSY: Name of the zones and unlocking/sensors in the handle of

the front door



The vehicle is locked/unlocked when the key is at a maximum distance of around

1.5 m from the handle on the front door or from the handle of the boot lid.

Unlocking and locking



Unlocking

Grab the door handle of the front door or cover the sensor 2 » Fig. 15 with the

›

whole palm of your hand » .

Locking

Touch the sensor 1 » Fig. 15 with your fingers.

›

Unlocking the boot lid

Press the handle of the boot lid » Fig. 19 on page 37.

›

Switching off the safelock system

Use your fingers to touch the sensor 1 twice within 2 seconds.

›

The vehicle can be unlocked when the key is in the unlocking zone.

Unlocking zones

Front door left

Front door right

Luggage compartment lid

If you cover the sensor locking the vehicle, it is not unlocked.

If the vehicle is locked via the sensor in the following 2 seconds via the sensor 2 - prevents accidental unlocking.

On vehicles fitted with automatic gearbox, the selector lever must be moved into the position P before unlocking.

The KESSY system can find the valid key, even if it was left in the front of the vehicle's roof for example where the key is.

Always check to see whether the vehicle is locked.

at the same time as the sensor 1 » Fig. 15 when un-

, it will not be possible to unlock it again

» Fig. 15. It is therefore not always necessary to know

CAUTION

■

After leaving the vehicle, it does not lock automatically, the procedure for lock-

ing the vehicle must therefore be observed.

■

Do not use gloves or other objects which might prevent direct contact between

the hand and the sensor.

Protection against inadvertently locking the key in the vehicle

If the key which was used to lock the vehicle including the boot lid, remains in the vehicle, the protection mechanism against inadvertently locking the key in the vehicle is activated and the vehicle unlocks itself again D » Fig. 15 on page 33.

The turn signal lights flash four times as confirmation that the vehicle has been unlocked again.

The following message is displayed in the information display or display of the instrument cluster: Key in vehicle. or KEY IN VEHICLE.

Additionally, on vehicles which are fitted with the anti-theft alarm system, an audible signal sounds.

Information message

The functions of the KESSY system are monitored. In the presence of a fault, one of the following messages may appear.

Key not found.

›

Key not detected. Owner's manual!

›

NO KEY

›

This message is displayed if you leave the engine on and no key is detected in the vehicle. The message is then displayed when the ignition is switched on or the engine is running or when no key was found in the vehicle. This can occur if the key is outside the vehicle, the battery in the key is discharged, the key is defective or the electromagnetic field is strongly disturbed. Some electronic devices, e.g. mobile phones, can also cause faults.

Keyless access system faulty.

›

KEYLESS ACCESS SYSTEM FAULTY

›

Error in the KESSY system; seek help from a ŠKODA specialist garage.

Change the key battery!

›

KEY BATTERY PLEASE CHANGE

›

Low voltage of the remote control key battery, change the battery.



Note

■

If the battery in the key is weak or discharged, the vehicle may not be unlocked or locked via the KESSY system. In this case, use the emergency unlocking or emergency locking on the driver's door » page 36.

Using the system



Parking the vehicle

If the vehicle is not unlocked within 60 or 90 seconds, the sensors in the handle of the driver /front passenger's door is deactivated automatically » Fig. 15 on page 33.

Activation after 60 hours

Unlock the driver's door using the sensor 2 » Fig. 15 on page 33.

›

Press the handle of the boot lid.

›

Unlock the vehicle using the button  on the remote control key.

›

Unlocking the driver's door in an emergency » page 36.

›

Activation after 90 hours

Unlock the vehicle using the button  on the remote control key.

›

Unlocking the driver's door in an emergency » page 36.

›

Anti-theft alarm system

Introductory information

The anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle.

Activating

The anti-theft alarm system is activated by locking the vehicle or inserting the key in the driver's door. It is activated 30 seconds after locking the door.

Deactivating

The anti-theft alarm system is deactivated by unlocking the vehicle. If the vehicle is not opened within 45 seconds, the anti-theft alarm system is automatically activated again.

The alarm system is also deactivated if you unlock the driver door using the key within 45 seconds of locking the vehicle.

If the vehicle is unlocked by inserting the key into the driver door, the key must be inserted into the ignition lock and the ignition switched on within 15 seconds of unlocking the door to deactivate the alarm system. The alarm is triggered if the ignition is not switched on within 15 seconds.

Triggering the alarm

An alarm is triggered when the following monitored areas of the vehicle have a fault:

bonnet;

›

boot lid;

›

doors;

›

ignition lock;

›

Vehicle inclination » page 36;

›

Interior of the vehicle » page 36;

›



A drop in voltage of the on-board power supply;

›

Socket of the factory-fitted towing device » page 110, Driving with a trailer.

›

An alarm is immediately triggered if either of the two battery terminals is disconnected while the anti-theft alarm system is activated.

Switching off the alarm

The alarm is switched off by unlocking the vehicle or switching on the ignition.

CAUTION

Before leaving the car, it must be checked that all of the windows, doors and the sliding/tilting roof are properly closed to ensure the full functionality of the antitheft alarm system.

Note

The working life of the alarm siren is 5 years.



Unlocking and locking

Interior monitor and towing protection

Emergency unlocking/locking

Fig. 16

Button for interior monitor and towing protection

The interior monitor detects movements inside the car or the inclination of the vehicle and then triggers the alarm.

Switching off

Switch off the ignition.

›

Open the driver door.

›

Press the button  » Fig. 16 on the centre column on the driver side, the sym-

›

bol  that lights up in the button changes from red to orange.

Lock the vehicle within 30 seconds.

›

The interior monitor and the towing protection are activated automatically after the vehicle is locked.

The anti-theft alarm system is activated when the vehicle is locked when the safelock system is activated. The interior monitor is however not activated.

Deactivate the interior monitor and the towing protection if there is a possibility of the alarm being triggered by movements from (e.g. children or animals) within the vehicle interior or if the vehicle has to be transported (e.g. by train or ship) or towed.

CAUTION

The opened glasses storage compartment reduces the effectiveness of the interior monitor. To ensure the full functionality of the interior monitor, the glasses storage compartment must always be closed before locking the vehicle.

Unlocking/locking the driver's door

Fig. 17 Handle on the driver's door: covered locking cylinder/locking cylinder with key

Pull on the handle.

›

Push the vehicle key into the recess on the bottom side of the cover in the area

›

of the arrow and fold upwards » Fig. 17 . Put the vehicle key (the symbols face upwards) into the locking cylinder and

›

lock/unlock the vehicle .

CAUTION

Make sure you do not damage the paint when performing an emergency locking/ unlocking.

Locking a door

Fig. 18

Rear door: Emergency locking





Using the system

An emergency locking mechanism is located on the face side of the doors which have no locking cylinder, it is only visible after opening the door.

Remove the panel A » Fig. 18.

›

Insert the key into the slot B and turn it into the horizontal position in the di-

›

rection of the arrow (mirror-inverted on the right doors). Replace the cover.

›

After closing the door, it cannot be opened from the outside. The door is unlocked by pulling on the door opening lever and is then opened from the outside.

Luggage compartment lid



Introduction

This chapter contains information on the following subjects: Opening/closing 37

Automatic locking Emergency unlocking

WARNING

■

Ensure that the lock is properly engaged after closing the luggage compartment lid. Otherwise, the boot lid might open suddenly when driving even if it was locked– risk of accident!

■

Never drive with the luggage compartment lid fully opened or slightly ajar otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning!

■

Do not press on the rear window when closing the luggage compartment lid, it could crack – risk of injury!

CAUTION

If the vehicle was locked before the boot lid was closed, the lid is automatically locked right away as soon as it is closed.

Note

The function of the handle above the licence plate is deactivated when starting off or at a speed of 5 km/hour or more for vehicles with central locking. The function is restored after the vehicle stops and the door is opened.

38 38

Opening/closing



Fig. 19 Handle of boot lid

Fig. 20

Handle in the inner panelling of the boot lid

First read and observe the introductory information and safety warnings



After unlocking, the boot lid can be opened with the handle above the number plate.

Opening

Press the handle A » Fig. 19 and raise the lid in the direction of the arrow B.

›

Closing

Pull the lid down the handle C » Fig. 20 and close with a slight swing.

›



on page 37.



Unlocking and locking

Automatic locking

First read and observe the introductory information and safety warnings on page 37.



If the vehicle was locked before the boot lid was closed, the lid is automatically locked right away as soon as it is closed.

This feature can be activated/deactivated by a ŠKODA Partner.

Delayed locking

If the boot lid was unlocked with the button  on the remote control key, then it is possible to open the lid within a limited period of it being closed.

There is a risk of unwanted entry into the vehicle before the boot lid is locked automatically. Always lock the vehicle using the button with the key if no remote control is available » page 31.



on the remote control or

Note

More detailed information is available from your authorised ŠKODA Partner.

Emergency unlocking

Fig. 21

Emergency unlocking of the luggage compartment lid

First read and observe the introductory information and safety warnings on page 37.



Fold the rear seat backrest forward » page 63.

›

Insert the vehicle key into the slot in the trim panel as far as the stop.

›

Unlock the lid by moving it in the direction of the arrow.

›

Open the luggage compartment lid.

›

Electrical power windows

 Introduction

This chapter contains information on the following subjects: Opening/closing the window from the driver seat

Opening the windows in the front passenger door and in the rear doors 40 Force limiter 40 Window convenience operation 40 Operational faults in the automatic power windows 41

The electrical power windows can only be operated when the ignition is switched on.

After switching the ignition off, it is still possible to open or close the windows for approx. 10 minutes. The electrical power windows are only switched off completely once the driver's door or front passenger door are opened.



When driving always use the existing heating, air conditioning and ventilation system for ventilating the interior of the vehicle. If the windows are opened, dust as well as other dirt can get into the vehicle and in addition the wind noise is more at certain speeds.

The prerequisite for ensuring that the convenience operating feature correctly is the automatic opening/closing of all windows is operational.

WARNING

■

Ensure that no persons are still left in the vehicle when locking the vehicle. In an emergency, the windows will no longer be able to be opened from the inside.

■

The system is fitted with a force limiter » page 40. If there is an obstacle, the closing process is stopped and the window goes down by several centimetres. The windows should nevertheless be closed carefully! Otherwise these can cause severe crushing injuries!

■

It is recommended to deactivate the electrical power windows in the rear doors (safety pushbutton) S » Fig. 22 on page 39 when children are being transported on the rear seats.





Using the system

CAUTION

■

Keep the windows clean to ensure the correct functionality of the electric win-

dows.

■

In the event that the windows are frozen, first of all eliminate the ice » page 162, De-icing windows and exterior mirrors and only then operate the electrical power windows. Otherwise, the electrical power window mechanism could be damaged.

■

When leaving the locked vehicle make sure that the windows are closed at all times.

For the sake of the environment

At high speeds, you should keep the windows closed to prevent unnecessarily high fuel consumption.

Note

The window lift system is equipped with protection against overheating. Repeated opening and closing of the window can cause this mechanism to overheat. If this happens, it will not be possible to operate the window for a short time. You will be able to operate the window again as soon as the overheating protection has cooled down.

Opening/closing the window from the driver seat

Fig. 22

Buttons on the driver's door

Opening

A window is opened by pressing lightly on the respective button. The opening

›

process stops when one releases the button.

The window can be completely opened automatically by briefly pressing the button as far as the stop. Renewed pressing of the button causes the window to stop immediately.

Closing

The window is closed through pulling lightly on the respective upper edge of

›

the button. The closing process stops when one releases the button.

The window can be fully closed automatically by briefly pulling the button as far as the stop. Renewed pulling of the button causes the window to stop immediately.

Buttons for the electrical power windows » Fig. 22.

Button for electrical power window of the driver's door

Button for electrical power window of the front passenger door

Button for electrical power window of the rear right door

Button for electrical power window of the rear left door

Safety pushbutton



Safety pushbutton

The buttons for electrical power windows in the rear doors can be deactivated by pressing the safety pushbutton windows in rear doors are activated again by pressing the safety pushbutton again.

If the buttons for the rear doors are deactivated, the warning light  in the safety switch S lights up.

» Fig. 22. The buttons for the electrical power



First read and observe the introductory information and safety warnings on page 38.



Unlocking and locking

Opening the windows in the front passenger door and in the rear doors

Fig. 23

Button arrangement in the front passenger door

First read and observe the introductory information and safety warnings on page 38.



There is a button in the front passenger door and in the rear doors for that window.

Opening

Lightly press the appropriate button down and hold it until the window has

›

moved into the desired position.

The window can be completely opened automatically by briefly pressing the button down as far as the stop. Renewed pressing of the button causes the window to stop immediately.

Closing

Lightly press the appropriate button up and hold it until the window has moved

›

into the desired position.

The window can be completely closed automatically by briefly pressing the button up as far as the stop. Renewed pressing of the button causes the window to stop immediately.

Force limiter

First read and observe the introductory information and safety warnings on page 38.



The electrical power window system is fitted with a force limiter. It reduces the risk of bruises or injuries when closing the windows.

If there is an obstacle, the closing process is stopped and the window goes down by several centimetres.

If the obstacle prevents the window from being closed during the next 10 seconds, the closing process is interrupted once again and the window goes down by several centimetres.

If you attempt to close the window again within 10 seconds of the window being moved down for the second time, even though the obstacle was not yet been removed, the closing process is only stopped. During this time it is not possible to automatically close the window. The force limiter is still switched on.

The force limiter is only switched off if you attempt to close the window again within the next 10 seconds - the window will now close with full force!

If you wait longer than 10 seconds, the force limiter is switched on again.

Window convenience operation

First read and observe the introductory information and safety warnings on page 38.



Convenience opening/closing of all windows can be operated by locking/unlocking the vehicle as follows:

Opening

Press and hold the unlock button  on the key.

›

Hold the key in the driver's lock in the unlock position.

›

Closing

Press and hold the unlock button  on the key.

›

Hold the key in the driver's lock in the lock position.

›

In the KESSY system, hold a finger on the sensor 1 » Fig. 15 on page 33.

›

Immediately after unlocking the vehicle or switching off the ignition and opening



the driver's or front passenger's door, convenience opening/closing of all windows can be operated with the key

Opening

Hold the button in the opening position.

›

Closing

Hold the button in the closing position.

›

You can interrupt the opening or closing process for the windows immediately by releasing the key or the the button

» Fig. 22 on page 39 as follows:

and interrupting the locking/unlocking.





Using the system

The convenience opening of the windows by means of the key in the driver's/ front passenger's lock is only possible within 45 seconds of deactivating or activating the alarm system.

Setting options

Information on the setting » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Operational faults in the automatic power windows

First read and observe the introductory information and safety warnings



The automatic power windows do not work if the vehicle battery was disconnected and connected while a window is open. The system must be activated.

Proceed as follows in order to re-establish the function:

Switch on the ignition.

›

Pull the top edge of the button and close the window.

›

Release the button.

›

Pull the relevant button upwards again for approx. 3 seconds, and keep it press-

›

ed down. In the winter, ice accumulating on the surface of the window may cause there to

be more resistance when closing the window. The window will stop and move back several centimetres.

It is necessary to deactivate the force limiter to close the window » page 40.

on page 38.

Power panoramic sliding/sliding tilting roof

Introductory information

The power panoramic sliding/tilting roof (abbreviated in the following as 'sliding/ tilting roof'), can only be when the ignition is turned on and when the outdoor temperature is higher than -20 °C.

The sliding/tilting roof can still be operated for approx. 10 minutes after switching the ignition off. However, as soon as the driver or front passenger's door is opened it is no longer possible to operate the sliding/tilting roof.

CAUTION

■

Always close the sliding/tilting roof before disconnecting the battery.

■

If the battery has been disconnected and reconnected, it is possible that the sliding/tilting roof does not operate correctly. Next, move the rotary switch into position A » Fig. 24 on page 41, pull it, and hold onto the recess downwards



and forwards tightly. The sliding/tilting roof opens and closes again after around 10 seconds. Do not release the control dial until it has done so.

Using the system

Fig. 24

Control dial for the sliding/tilting roof

Comfort position

Turn the switch to position C » Fig. 24.

›

When the sliding/tilting roof is in the comfort position, the intensity of the wind



noise is reduced.

Open partially

Turn the switch to a position in area D.

›

Open fully

Turn the switch to position B and hold it in this position (spring-tensioned po-

›

sition).

Tilting roof

Turn the switch to position A.

›

Press the switch in the region of the lug E towards the roof.

›

Closing

Turn the switch to position A » Fig. 24.

›

Press the switch on the recess Edown and then pull it forwards.

›





Unlocking and locking

Force limiter

The sliding/tilting roof is fitted with a force limiter. The sliding/tilting roof stops and moves back several centimetres when it cannot be closed because there is something in the way (e.g. ice). The sliding/tilting roof can be fully closed without a force limiter by pressing the switch on the recess down and then pushing it forward until the sliding/tilting roof is fully closed » .

WARNING

When closing the sliding/tilting roof proceed with caution to avoid causing crushing injuries - risk of injury!

CAUTION

During the winter it may be necessary to remove any ice and snow in the vicinity of the sliding/tilting roof before opening it to prevent any damage to the opening mechanism.

Convenience operating feature of the sliding/tilting roof

The sliding/tilting roof can be operated by locking/unlocking using the key or using the KESSY system with the aid of the sensor 1 » Fig. 15 on page 33.

Closing

Press and hold the button  on the key or hold the key in the locking cylinder

›

of the driver's door in the lock position, or with the KESSY system, keep your finger on the sensor 1 » Fig. 15 on page 33 » .

By releasing the lock or lifting your finger off the sensor 1 when using the KESSY system, the closing process is immediately interrupted.

Tilting roof

Press and hold the unlock button  on the key.

›

WARNING

Close the sliding/tilting roof carefully - risk of injury! The force limiter does not operate with the convenience closing.



Note

The sliding/tilting roof cannot be opened using the convenience operating feature.

Using the system



Lights and visibility

Lights

Introduction



This chapter contains information on the following subjects: Side lights and the low beam

Daylight driving light function (DAY LIGHT) 44 Turn signal and main beam light 45 Automatic driving lamp control 45 Adaptive headlights (AHL) 46 Headlight assist 47 Fog lights Fog lights with the function CORNER 48 Rear fog light COMING HOME/LEAVING HOME function Hazard warning light system 49

The light only operates if the ignition is switched on. On models fitted with right-hand steering the position of certain switches differs

from that shown in » Fig. 25 on page 44. The symbols which mark the switch positions are identical, however.

The low beam continues to shine while the ignition is switched on and the light switch is in the position  or is switched off automatically and only the side lights come on. The side light goes out after the ignition key is removed.

Keep the headlights lenses clean. The following guidelines must be observed » page 162, Headlight lenses.



. After switching off the ignition, the low beam

WARNING

■

The activation of the lights should only be undertaken in accordance with

national legal requirements.

■

The driver is always responsible for the correct settings and use of the

lights.

■

The automatic driving lamp control  only operates as a support and does not release the driver from his responsibility to check the light and, if necessary, to switch on the light depending on the light conditions. The light sensor cannot, for example, detect rain or snow. Under these conditions we recommend switching on the low beam or fog lights!

Note

■

If there is a fault in the light switch, the low beam comes on automatically.

■

The headlights may mist up temporarily. When the driving lights are switched

on, the light outlet surfaces are free from mist after a short period, although the headlight lenses may still be misted up in the peripheral areas. This mist has no influence on the life of the lighting system.

■

The instruments are also illuminated when the side light, low or high beam light

is switched on. The brightness of the instrument lighting can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Set- ting vehicle systems (CAR button).



Lights and visibility

Side lights and the low beam

Fig. 25

Dash panel: Light switch and control dial for the headlight beam range regulation

First read and observe the introductory information and safety warnings on page 43.



Switching on the parking light

Turn the light switch to position  A » Fig. 25.

›

Switching on the low beam

Turn the light switch to position  A » Fig. 25.

›

Switching off lights (except daytime running lights)

Turn the light switch to position 0 A » Fig. 25.

›

Switching on the side light on both sides

Turn the light switch into the position  A » Fig. 25 and lock the vehicle.

›

Headlight beam adjustment

Turn the control dial B » Fig. 25 to the desired width of illumination.

›

The positions of the width of illumination correspond approximately to the following car load.

Front seats occupied, luggage compartment empty.

All seats occupied, luggage compartment empty.

All seats occupied, luggage compartment loaded.

Driver seat occupied, luggage compartment loaded.

WARNING

Always adjust the headlight range adjustment in such a way that:

■

it does not dazzle other road users, especially oncoming traffic;

■

and the range is sufficient for safe driving.

Note

■

The Bi-Xenon bulbs adapt automatically to the load and driving state of the vehicle when the ignition is switched on and when driving. Vehicles that are equipped with Bi-Xenon headlights do not have a manual headlight range adjustment control.

■

We recommend you adjust the headlight beam when the low beam is switched on.

Daylight driving light function (DAY LIGHT)

First read and observe the introductory information and safety warn-

on page 43.

ings



Switching on daytime running lights

Turn the light switch to position 0 or

›

Deactivating the daytime running lights feature on vehicles without Infotainment

Pull the turn signal and main beam lever to the steering wheel and push down-

›

wards » Fig. 26 on page 45.

At the same time switch on the ignition and hold the lever down in this position

›

for at least 3 seconds.

Activating the daytime running lights feature on vehicles without Infotainment

Pull the turn signal and main beam lever to the steering wheel and push up-

›

wards » Fig. 26 on page 45.

At the same time switch on the ignition and hold the lever down in this position

›

for at least 3 seconds.

The daytime running light can be activated/deactivated in the Infotainment » op-

erating instructions for Infotainment, chapter Setting vehicle systems (CAR button).



» Fig. 27 on page 45.

Note

When the daytime running light is switched on, the side lights (neither at the front or rear) and the number plate lights are not lit.



Using the system

Turn signal and main beam light

Fig. 26

Operating lever: Turn signal and main beam operation

First read and observe the introductory information and safety warnings on page 43.



The parking light and headlight flasher are also operated with the operating lever.

Switching on the right  and left  turn signal light

Put the lever into position A or where applicable B as far as it can go » Fig. 26.

›

If you only wish to flash three times (convenience turn signal), briefly push the lever to the pressure point A or where applicable B and release again.

The convenience turn signal can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Switching the main beam  on/off

Turn the light switch into position

›

Place the lever in position C (spring-tensioned position) » Fig. 26.

›

The main beam can be switched off by pulling the lever into position D (spring-

›

tensioned positioned).

On vehicles with Headlight assist, when the lever is put into position C, the Assistant is activated » page 47.

Switching on the headlight flasher (main beam)

Place the lever in position D.

›

Switching on the  parking light

Switch off the ignition.

›

Place the lever into the position A or where applicable B as far as it can

›

go » Fig. 26 - the side light on the right/left side of the vehicle is switched on.



or  » Fig. 25 on page 44.



WARNING

Only use the main beam or the headlight flasher if other road users will not be dazzled.

Note

■

The turn signal light automatically switches itself off when driving around a

curve or after making a turn.

■

The warning light flashes at twice its normal rate if a bulb for the turn signal

light fails.

■

If the right or left turn signal light has been switched on and the ignition is

switched off, the parking light is not automatically switched on.

Automatic driving lamp control

Fig. 27

Dash panel: Light switch

First read and observe the introductory information and safety warnings



If the light switch is in position plate light are switched on/off automatically based on the current light conditions.

The light is regulated based on the data provided by the light sensor in the rear mirror holder. The sensitivity of the light sensor can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehi- cle systems (CAR button).

Activating

Turn the light switch into position

›

on page 43.



, the the side lights and low beam and number



» Fig. 27.





Lights and visibility

Deactivating

Turn the light switch to position 0,  or  » Fig. 27.

›

If the light switch is in position , the symbol  lights up next to the light switch. If the light is switched on automatically, the symbol  next to the light switch also lights up.

Automatic headlight control in rain

If the light switch is in position  and if automatic wiping in rain or wiping (position 2 or 3) is switched on for longer than 30 seconds » page 54, the side lights and low beam will switch on automatically.

The light switches off when automatic wiping/wiping (position 2 or 3) is not switched on for longer than approx. 4 seconds.

The automatic headlight control in rain can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle sys- tems (CAR button).

CAUTION

Do not affix any stickers or similar objects in front of the light sensor on the windscreen, so that its functionality is not impaired or disabled.

Adaptive headlights (AHL)

First read and observe the introductory information and safety warn-

on page 43.

ings



The AFS system works in tandem with automatic driving lamp control read the following » page 45.

The AFS system makes sure the street remains lit up depending on the traffic and weather situation.

The system automatically adjusts the cone of light in front of the vehicle based on the vehicle speed, whether the windscreen wipers are in use, the rear fog lights, and data from Infotainment Navigation.

Activating

Turn the light switch into position

›

Deactivating

Turn the light switch to position 0,  or  » Fig. 27 on page 45.

›

The AHL system operates in the following modes.



» Fig. 27 on page 45.



, please

Out of town mode

The cone of light in front of the vehicle is similar to the low beam. The mode is active if none of the following modes are active.

City mode

The cone of light in front of the vehicle is adjusted so that it illuminates the adjacent pavement, crossings, etc. The mode is active at speeds of 15-50 km/h.

Motorway mode

The cone of light in front of the vehicle is adjusted so that the driver can respond in time to an obstruction or other hazard in time. The mode is active at speeds above 110 km/h.

Rain mode

The cone of light in front of the vehicle is adjusted so that the driver can reduce the glare from oncoming traffic in rain. The mode is active at speeds of 50 – 90 km/h and if the windscreen wipers continuously operate for a period of time longer than 2 minutes. The mode is deactivated when the windscreen wipers are switched off for longer than 8 minutes.

Fog mode

The cone of light in front of the vehicle is adjusted so that the driver is not daz-



zled by the reflection of the cone of light by fog in front of the vehicle. The mode is active at speeds of 15 – 70 km/h and if the rear fog light is switched on for a period of time longer than 10 seconds. The mode is deactivated when the rear fig light is switched off for longer than 5 seconds.

Dynamic cornering lights

The cone of light in front of the vehicle is adjusted to the steering angle so that the road in the curve is illuminated. This function is active at speeds greater than 10 km.h and in all AFS modes.

Tourist light

This mode makes it possible to drive in countries with opposing traffic system, driving on the left/right, without dazzling the oncoming vehicles. When the “tourist light” mode is active, the above-mentioned modes and the side swivel of the headlights is deactivated.

The "Tourist light" mode can be configured in the Infotainment » operating in- structions for Infotainment, chapter Setting vehicle systems (CAR button).



Using the system

WARNING

If the AFS system is defective, the headlights are automatically lowered to the emergency position, which prevents a possible dazzling of oncoming traffic. This reduces the cone of light in front of the vehicle. Drive carefully and visit a ŠKODA specialist garage as soon as possible.

Note

■

When the “tourist light” mode is active, the warning light  flashes for 10 sec-

onds each time the ignition is switched on.

■

If the Eco driving mode is selected, dynamic cornering lights are deactiva-

ted » page 124.

Headlight assist

Fig. 28

Operating lever: Headlight assist

First read and observe the introductory information and safety warnings



The Headlight assist switches the headlights on/off automatically depending on the environmental conditions.

The headlight is regulated based on data gathered by the camera attached between the windscreen and interior mirror.

The headlight can switch off automatically at speeds above 60 km/h. The headlight switches off automatically when the speed falls below 30 km/h.

When the Assistant switches on the headlight automatically, the indicator light lights up in the dash panel insert.

on page 43.

Activating

Turn the light switch into position  » Fig. 27 on page 45.

›

Place the lever in position A (spring-tensioned position) » Fig. 28.

›

In the instrument cluster display, the indicator light  appears for the activated Headlight assist.

Deactivating

If the headlight is currently switched on automatically, move the lever into posi-

›

tion B (spring-tensioned position) » Fig. 28. If the headlight is not currently switched on automatically, move the lever into

›

position A (the headlight switches on) followed by position B.

If you want to reactivate the Assist, put the lever back into position



The Assist can also be switched off when the light switch is turned from position



to another position.

If the system cannot function correctly, the following message will appear in the instrument cluster display:

Fault: Light Assist

LIGHT ASSIST FAULT

Seek help from a ŠKODA specialist garage.

Light Assist: clean the windscreen!

WINDSCREEN PLEASE CLEAN

Check for any obstacles on the windscreen in the viewing area of the camera. The function of Headlight assist can be activated/deactivated in the Infotain-

ment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Manually switching on the headlights

If the headlight is not switched on automatically, it can be switched on manually put the lever into position goes out.

Manually switching off the headlights



If the headlight is switched on automatically, it can be switched off manually - put the lever into position out.

. The Assist is deactivated; the indicator light

. The Assist is deactivated; the indicator light  goes





Lights and visibility

WARNING

Headlight assist only functions as a support and does not relieve the driver of his responsibility to check the headlights and light beam and, if necessary, to switch on the lights depending on the light conditions. Manual operation may be required in the following situations:

■

in poor visibility conditions, e.g. fog, heavy rain, thick snowfall;

■

on A roads or motorways when oncoming traffic is partially obscured;

■

when passing poorly lit traffic, e.g. cyclists;

■

around sharp curves;

■

on sharp slopes up/down;

■

while driving through poorly-lit villages;

■

while driving over highly reflective surfaces;

■

when the windscreen around the camera is dirty, iced up, misted up, or cov-

ered up by stickers;

■

when an external navigation system is attached to the windscreen.

CAUTION

■

Do not attach any stickers or similar objects to the windscreen to avoid impair-

ing the functions of the Assist system.

Fog lights

Fig. 29

Dash panel: Light switch

First read and observe the introductory information and safety warnings on page 43.



Switching on/off

Turn the light switch into position  or   » Fig. 29.

›

Pull the light switch to position 1.

›

The rear fog light is switched off in the reverse order.

The warning light  lights up in the instrument cluster when the fog lights are switched on » page 12.

Fog lights with the function CORNER

First read and observe the introductory information and safety warnings



The fog lights with the function CORNER are designed to improve the illumination of the surrounding area near the vehicle when turning, parking, etc.

The fog lights with the function CORNER are adjusted according to the steering angle or after switching on the turn signal light 1) in the following circumstances:

the vehicle is stationary and the engine is running or it moves with a speed of

›

maximum 40 km/h;



the daytime running lights are not switched on;

›

the low beam is switched on or the light switch is in the position

›

low beam is switched on;

the fog lights are not switched on.

›

on page 43.



Note

The two fog lights are switched on when you shift into the reverse gear.

Rear fog light

First read and observe the introductory information and safety warnings on page 43.



Switching on/off

Turn the light switch into position

›

Pull the light switch to position 2.

›

The rear fog light is switched off in the reverse order.



or   » Fig. 29 on page 48.



and the





If both switch on versions are conflicting, for example if the steering wheel is turned to the left and the right turn signal light is switched on, the turn signal light has the higher priority.

Using the system

If the vehicle is not fitted with fog lights, the rear fog light is switched on by pulling out the light switch directly to the position 2. This switch only has one position.

The warning light  lights up in the instrument cluster when the rear fog light is switched on » page 12.

When the rear fig light is switched on in towing mode, only the rear fog light of the trailer will light up. This is only the case when the trailer is coupled to a factory-fitted towing device/a towing device from ŠKODA Original accessories.

The COMING HOME/LEAVING HOME function can be configured in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Depending on the equipment fitted the COMING HOME/LEAVING HOME function switches on the following lights:

Parking lights;

›

Low beam;

›

Entry lighting in the exterior mirrors;

›



Licence plate light.

›

COMING HOME/LEAVING HOME function

First read and observe the introductory information and safety warnings on page 43.



In poor visibility conditions, this function makes it possible to automatically switch on the lights for a short time after leaving the vehicle or when approaching the vehicle.

The intensity of the surrounding light for switching on the lights is controlled with the light sensor in the interior mirror holder.

Switching on the COMING HOME function

Turn the light switch into position

›

Switch off the ignition.

›

The light switches on after opening the driver's door.

Switching off the COMING HOME function

Close all doors and the luggage compartment lid.

›

The light switches off after the pre-set time has passed. If a door or the boot lid remains open, the light goes out after 60 seconds.

Switching on the LEAVING HOME function

Before leaving the vehicle, turn the light switch into position

›

page 45.

The light switches on after unlocking the vehicle with the remote control.

Switching off the LEAVING HOME function

The light switches off after the pre-set time has passed or before the pre-set time has lapsed after the ignition is switched on or the vehicle is locked.



» Fig. 27 on page 45.



» Fig. 27 on

CAUTION

Do not affix any stickers or similar objects in front of the light sensor on the windscreen, so as not to impair or disable the COMING HOME/LEAVING HOME function.

Note

If the COMING HOME/LEAVING HOME function is switched on continuously, the battery will be heavily discharged particularly over short distances.

Hazard warning light system

Fig. 30

Dash panel: Button for hazard warning light system

First read and observe the introductory information and safety warnings on page 43.



Switching on/off

Press the button  » Fig. 30.

›

Lights and visibility





All the turn signal lights on the vehicle flash at the same time when the hazard warning light system is switched on. The warning light for the turn signals and the warning light in the button also flash at the same time. The hazard warning light system can also be operated if the ignition is switched off.

If one of the airbags is deployed, the hazard warning light system will switch on automatically.

When the turn signal is switched on while the hazard warning light system is on (ignition on), only the turn signal light for the selected driving direction will flash while the turn signal is switched on.

Note

The hazard warning light system must be switched on if, for example:

■

you encounter a traffic congestion;

■

your car breaks down.



Using the system

Interior light

Interior lights at the front

Fig. 31 Interior lights at the front

Fig. 32

Reading lights

Switching on the light

Press the button in the area of the symbol  » Fig. 31.

›

Switching off the light

Press the button in the area of the symbol O » Fig. 31.

›

Operating with the door contact switch

Place the button in the middle position.

›

On vehicles without an interior monitor, the middle position is marked with the symbol  » Fig. 31 - .

Switching the reading light on/off

Press the button  or  » Fig. 32.

›

If operating lights with the door contact switch is enabled, the light will come on when:

the vehicle is unlocked;

›

one of the doors is opened;

›

or the ignition key is removed.

›

If operating lights with the door contact switch is enabled, the light will go off when:

the vehicle is locked;

›

the ignition is switched on;

›

about 30 seconds after all the doors have been closed.

›

Note

■

If the interior light remains switched on when the ignition is switched off or if one of the doors is open, the light will automatically go out after around 10 minutes.

■

Two diffuse lights are integrated in the front interior lighting, that illuminate the gearshift lever and the middle of the dash panel. These are switched on automatically when the parking light is activated. Also, after switching on the ignition when the parking lights are switched on, the door handle lighting comes on.

Interior lights at the rear

Fig. 33

Interior light/interior light with reading lights

The rear interior light is operated together with the front interior light » Fig. 31 on page 51.





Lights and visibility

Switching the light on/off

Press the button  » Fig. 33 - .

›

Switching the reading light on/off

Press the button  or  » Fig. 33 - .

›

Note

If the door is open and the ignition switched off, the light will extinguish automatically after around 10 minutes.



Front door warning light

Fig. 34

Front door: Warning light

The warning light is located in the lower door trim panel » Fig. 34. The light switches on/off when the front door is opened or closed.

Note

If the door is open and the ignition switched off, the light will extinguish automatically after around 10 minutes.

Entry lighting

The lighting is positioned on the bottom edge of the exterior mirror and illuminates the entry area of the front door.

The light comes on after the vehicle has been unlocked or on opening the front door. The lighting goes out within around 30 seconds after the front door is closed or the ignition is switched on.

WARNING

If the entry light is on, do not touch its cover - risk of burns!

Visibility

Windscreen and rear window heater

Buttons for the front and rear window heater/manual air-condition-

Fig. 35

ing system, heating

Switching the windscreen heater on/off



Press the button  » Fig. 35.

›

The indicator light in or underneath the button lights up/goes out.

Switching the rear window heater on/off

Press the button  » Fig. 35.

›

The indicator light in or underneath the button lights up/goes out.

The windscreen and rear window heater only operates when the engine is running.

The windscreen and rear window heater automatically switches off after approximately 10 minutes.



Using the system

For the sake of the environment

The heating should be switched off as soon as the window is de-iced or free from mist. The reduced current consumption will have a favourable effect on fuel economy » page 102, Convenience consumers.

Note

If the on-board voltage drops, the windscreen and rear window heater switches off automatically, to provide sufficient electrical energy for the engine control » page 180, Automatic load deactivation.

Sun screen

Fig. 37

Sun screen



Sun visors

Fig. 36

Sun visor: left/right

The sun visor for the driver or front passenger can be pulled out of the fixture and swivelled towards the door in the direction of the arrow 1 » Fig. 36.

The sun visors each have a vanity mirror B with a cover. Push the cover in the direction of the arrow 2.

The purpose of the note holder pad, etc.

is to store small, light objects, such as a note-

WARNING

The sun visors must not be swivelled towards the side windows in the deployment area of the head airbags if any objects, such as ball-point pens, etc. are attached to them. These objects might result in injuries to the occupants if the head airbag is deployed.

The sun screen is located in a housing on the luggage compartment cover.

Pulling out

Grab the handle B » Fig. 37.

›

Remove the sun screen and hang it from the brackets A.

›

Folding

Grab the handle B » Fig. 37.

›

Remove the sun screen from the brackets A and slowly roll it up again into the

›

housing on the luggage compartment cover.

Windscreen wipers and washers



Introduction

This chapter contains information on the following subjects: Windscreen wipers and washers 54

Headlight cleaning system Replacing the windscreen wiper blades 56 Replacing the rear window wiper blade

The windscreen wipers and the wash system only operate if the ignition is switched on and the bonnet is closed.

If the intermittent wipe is switched on, the intervals are also controlled depending on speed.



When automatic wiping in rain is active, the wiper intervals are regulated based on the intensity of the rain.

Lights and visibility





The rear window is wiped once automatically if the windscreen wipers are on when reverse gear is selected.

Automatic rear window wiping can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Top up with windscreen wiper fluid » page 176.

WARNING

■

Properly maintained windscreen wiper blades are essential for clear visibility

and safe driving » page 56.

■

Do not use the windscreen washer system at low temperatures, without heating the windscreen beforehand. Otherwise the window cleaner could freeze on the windscreen and restrict the view to the front.

■

Automatic wiping in rain only operates as a support. The driver is not released from the responsibility to set the function of the windscreen wipers manually depending on the visibility conditions.

■

Replace the windscreen wiper blades once or twice a year for safety reasons. These can be purchased from a ŠKODA Partner.

CAUTION

■

In cold temperatures and during the winter, check before the journey or before

switching on the ignition that the wiper blades are not frozen to the windscreen. If the windscreen wipers are switched on when the blades are frozen to the windscreen, this may damage both the blades and windscreen wiper motor!

■

If the ignition is switched off while the windscreen wipers are switched on, the

windscreen wipers will continue wiping in the same mode after the ignition is turned back on. The windscreen wipers could freeze up in cold temperatures between the time the ignition was turned off and when it was turned back on again.

■

Carefully detach frozen wiper blades from the front or rear window.

■

Remove snow and ice from the windscreen wipers before driving.

■

If the windscreen wipers are handled carelessly, there is a risk of damage to the

windscreen.

■

The ignition must not be switched on if the front windscreen wiper arms are fol-

ded out. The wiper blades would move back into their rest position and while doing so damage the paintwork of the bonnet.

Note

■

The windscreen wiper switches off each time the ignition switches off for the

third time. This counteracts an early fatigue of the wiper rubbers.

■

If there is an obstacle on the windscreen, the wiper will try to push away the obstacle. The wiper stops automatically after 5 attempts to eliminate the obstacle, in order to avoid a damage to the wiper. Remove the the obstacle and switch the wiper on again.

■

The rear window wiper only operates if the boot lid is closed.

■

The windscreen washer nozzles for the windscreen are heated when the engine is running and the outside temperature is less than approx. +10 °C.

■

Keep the wiper blades clean. The wiper blades can become soiled with wax residues after washing in automatic vehicle wash systems for example » page 160.

Windscreen wipers and washers

Fig. 38

Operating lever: Function of the the windscreen wipers and washers

First read and observe the introductory information and safety warnings on page 53.



Function of the windscreen wipers and washers in the individual positions » Fig. 38

Wipers off

Periodic windscreen wiping/automatic wiping in rain

slow windscreen wiping

rapid windscreen wiping

Flick windscreen wiping (spring-tensioned position)

Automatic wipe/wash for windscreen (spring-tensioned position)

Wiping the rear window pane (the windscreen wiper wipes every 6 seconds)





Using the system

Automatic wipe/wash for the rear window (spring-tensioned position)

Switches for setting the required break between the individual wiper strokes (1 periodic windscreen wiping) or the wiper speed in rain (1 automatic windscreen wiping in rain)

Automatic windscreen wiping in rain

Automatic windscreen wiping in rain can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Automatic wipe/wash for windscreen

The wash system operates immediately, the windscreen wipers wipe somewhat later. The wash system and the windscreen wiper operate simultaneously at a speed of more than 120 km/h.

Letting go of the lever will cause the windscreen wash system to stop and the wiper to continue for another 2 - 3 wiper strokes (depending on the period of spraying of the windscreen).

At a speed of more than 2 km/h, the wiper wipes once again 5 seconds after the last wiper stroke in order to wipe the last drops from the windscreen. This feature can be activated/deactivated by a ŠKODA specialist garage.

Automatic wipe/wash for the rear window

The wash system operates immediately, the windscreen wiper wipes somewhat later.

Letting go of the lever will cause the windscreen wash system to stop and the wiper to continue for another 2 - 3 wiper strokes (depending on the period of spraying of the windscreen). The lever remains in position

Winter setting of the windscreen wiper

If the windscreen wipers are in rest position, they cannot be folded out from the windscreen. For this reason we recommend adjusting the windscreen wipers in winter so that they can be folded out from the windscreen easily.

Switch on the windscreen wipers.

›

Switch off the ignition.

›

The windscreen wipers remain in the position in which they were when switching off the ignition.

The service position can also be used as a winter position » page 56.

Note

If the slower 2 » Fig. 38 or the faster 3 wiper setting is switched on and the vehicle speed decreases to below 4 km/h, the wiper speed is switched step by step into a lower wiper step. The original setting is restored step by step when the speed of the vehicle exceeds 8 km/h.

Headlight cleaning system

First read and observe the introductory information and safety warnings on page 53.



The headlights are always cleaned (after the ignition is switched on) after the first and every tenth spraying of the windscreen when the low beam is switched on and the lever is pulled into position

Every time the windscreen is cleaned represents the tenth time each headlight is sprayed.

To ensure the proper operation of the cleaning system during the winter, any snow should be removed from the washer nozzle fixtures and ice should be cleared with a de-icing spray.

» Fig. 38 on page 54.

CAUTION

Never remove the nozzles from the headlight cleaning system by hand – risk of damage!



Lights and visibility

Replacing the windscreen wiper blades

Replacing the rear window wiper blade

Fig. 39

Windscreen wiper blade

First read and observe the introductory information and safety warnings on page 53.



Before replacing the windscreen wiper blade, put the windscreen wiper arms into the service position.

Service position for changing wiper blades

Closing the bonnet.

›

Switch the ignition off and on again.

›

Within 10 seconds, press the lever in position 4 and keep it held for around 2

›

seconds » Fig. 38 on page 54.

The windscreen wiper arms move into the service position.

Removing the wiper blade

Raise the windscreen wiper arm away from the windscreen » Fig. 39.

›

Tilt the wiper blade as far as it can go in the direction of the windscreen wiper

›

arm - arrow A. Hold the upper part of the windscreen wiper arm and unlock the securing mech-

›

anism 1. Remove the wiper blade in the direction of the arrow B.

›

Attaching the wiper blade

Push the windscreen wiper blade until the stop and it locks in place.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arms back to the windscreen.

›

Turn on the ignition and press the lever into position 4 » Fig. 38 on page 54.

›

The windscreen wiper arms move into the home position.

Fig. 40

Rear window wiper blade

First read and observe the introductory information and safety warnings on page 53.



Removing the wiper blade

Raise the windscreen wiper arm away from the windscreen » Fig. 40.

›

Tilt the wiper blade as far as it can go in the direction of the windscreen wiper

›

arm - arrow A.

Hold the upper part of the windscreen wiper arm and unlock the securing mech-

›

anism

Remove the wiper blade in the direction of the arrow B.

›

Attaching the wiper blade

Push the windscreen wiper blade until the stop and it locks in place.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arm back to the windscreen.

›

Rear mirror



Introduction

This chapter contains information on the following subjects: Interior mirror 57

Exterior mirror





Using the system

WARNING

■

Make sure that the mirror is not covered by ice, snow, mist or other objects.

■

Convex (curved outward) exterior mirrors increase the field of vision. They do, however, make objects appear smaller in the mirror. These mirrors are therefore only of limited use for estimating distances to the following vehicles.

■

Whenever possible use the interior mirror for estimating the distances to the following vehicles.

■

Automatic dimming mirrors contain an electrolytic fluid which may leak should the mirror glass break. The leaking electrolytic fluid can irritate the skin, eyes and breath apparatus. Immediately seek out fresh air and leave the vehicle. If this is not possible, open all windows and doors.

■

If you swallow electrolytic fluid, seek medical assistance immediately.

■

If your eyes or skin come into contact with the electrolytic fluid, immediately wash the affected area for a few minutes long with a lot of water. Then consult a doctor immediately.

■

The illuminated display of an external navigation unit can lead to operational faults to the automatic dimming interior mirror- risk of accident.

CAUTION

Never mechanically fold in or fold back the exterior mirrors with the fold-in function  by hand as this will damage the electric drive.

Note

■

Automatic mirror dimming operates only properly if the sun screen for the rear

window in the housing on the boot cover is not in use or the light striking the interior rear-view mirror is not affected by other objects.

■

If the automatic interior mirror dimming is switched off, the exterior mirror dim-

ming is also switched off.

■

Do not touch the surface of the exterior mirrors if the exterior mirror heater is

switched on.

■

If the the electrical exterior mirror setting fails at any time, the two mirrors can

be adjusted by hand by pressing on the edge of the mirror surface.

■

Contact your ŠKODA specialist garage if there is a fault with the power setting

of the exterior mirrors.

Interior mirror

Fig. 41

Manual dimming mirror

Fig. 42 Automatic dimming mirror

First read and observe the introductory information and safety warnings



Manual dimming interior mirror

Adjust the lever towards the windscreen at the lower edge of the mirror (the

›

mirror dims) A » Fig. 41. Adjust the lever away from the windscreen at the lower edge of the mirror

›

(home position) B.

Activating/deactivating automatic dimming

Press the button B, the indicator light A lights up » Fig. 42.

›



To deactivate, press the button B again, the warning light A goes out.

If the automatic dimming is switched on, the mirror dims automatically depending on the light striking the mirror from the rear.

on page 56.



Lights and visibility

When the interior lights are switched on or the reverse gear is engaged, the mirror always moves back into the basic position (not dimmed).

Do not attach external navigation devices on to the windscreen or in the vicinity of the automatic dimming interior mirror » page 57, in section Introduction.

Exterior mirror

Fig. 43

Inner part of door: Rotary knob

First read and observe the introductory information and safety warnings on page 56.



Mirror heater

Set the rotary knob into the position  » Fig. 43.

›

The mirror heater only operates when the engine is running and up to an outside temperature of +35 ℃.

Adjusting both mirrors in sync

Set the rotary dial into position  or, on right-hand drive vehicles, into position

›



» Fig. 43. The movement of the mirror surface is identical to the movement of

the rotary knob.

The synchronous setting of both mirrors can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehicle sys- tems (CAR button).

Adjusting the front passenger's mirror

Set the rotary dial into position  or, on right-hand drive vehicles, into position

›

» Fig. 43. The movement of the mirror surface is identical to the movement of



the rotary knob.

Switching off operating control

Set the rotary knob into the position  » Fig. 43.

›

Folding-in both of the exterior mirrors with the rotary knob

Set the rotary knob into the position  » Fig. 43.

›

It is only possible to fold in both exterior mirrors when the ignition is switched on



and at a speed of up to 50 km/h. The mirrors are folded back into the driving position after the rotary knob is

turned from the position  to a different one.

Folding-in both of the exterior mirrors using the remote control key

Hold down the lock button  on the remote control key, or when using the

›

KESSY system, keep your finger on the sensor 1 » Fig. 15 on page 33.

Folding in requires that all electrical power windows are working » page 41, Op- erational faults in the automatic power windows.

The exterior mirror is folded back into the driving position when the ignition is switched on.

Folding in of both mirrors can be activated/deactivated in the Infotainment » op-

erating instructions for Infotainment, chapter Setting vehicle systems (CAR button).

Automatic dimming mirror

The exterior mirrors are dimmed together with the automatic dimming interior mirror » page 57.

Tilting surface of front passenger mirror

On vehicles fitted with the memory function for the driver seat » page 61, the surface of the mirror tilts down slightly when the reverse gear is engaged and the rotary knob is in the position  or in position  on vehicles with right-hand drive » Fig. 43. This provides an aid in seeing the kerb of the pavement when parking the car.

The mirror returns into its initial position, after the rotary knob is moved out of the position  or position  on vehicles with right-hand drive, and put into another position or if the speed is more than 15 km/h.

Tilting the surface of the front passenger mirror can be activated/deactivated in the Infotainment » operating instructions for Infotainment, chapter Setting vehi- cle systems (CAR button).

Memory function for mirrors

On vehicles fitted with the memory function for the driver seat » page 61 or the memory function for the remote control key » page 61 it is possible to save the position of the exterior mirror when saving the driver seat position.



Using the system

Seats and Stowage

Front seats

Introduction



This chapter contains information on the following subjects: Manually adjusting the front seats

Electrically adjusting the front seats 60 Memory function of the power seat 61 Memory function of the remote control key 61

The driver's seat should be adjusted in such a way that the pedals can be fully pressed to the floor with slightly bent legs.

The seat backrest on the driver's seat should be adjusted in such a way that the upper point of the steering wheel can be easily reached with slightly bent arms.

Correct adjustment of the seats is particularly important for:

safely and quickly reaching the controls;

›

a relaxed, fatigue-free body position;

›

achieving the maximum protection offered by the seat belts and the airbag

›

system.

WARNING (Continued)

■

Each occupant must correctly fasten the seat belt belonging to the seat. Children must be fastened » page 154, Transporting children safely with a suitable restraint system.

■

At all times, the front seats and head restraints must be adjusted to match the person's body size and the seat belt must be attached properly to provide the most effective levels of protection to passengers.

■

Always keep your feet in the footwell when the car is being driven – never place your feet on the instrument panel, out of the window or on the surfaces of the seats. This is particularly important for the front seat passenger. You will be exposed to increased risk of injury if it becomes necessary to apply the brake or in the event of an accident. If an airbag is deployed, you may suffer fatal injuries when adopting an incorrect seated position!

■

The driver must maintain a distance of at least 25 cm from the steering wheel, and a distance of at least 10 cm between the legs and the dash panel at the height of the knee airbag. The front passenger must maintain a distance of at least 25 cm to the dash panel. Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you – hazard!

■

Ensure that there are no objects in the driver's footwell as they may get caught behind the pedals when driving or applying the braking. You would then no longer be able to operate the clutch, brake or accelerate.

■

Do not transport any objects on the front passenger seat except objects (e.g. child safety seat) provided for this purpose – risk of accident!

WARNING

■

Only adjust the driver's seat when the vehicle is stationary – risk of accident!

■

Caution when adjusting the seat! You may suffer injuries or bruises as a re-

sult of adjusting the seat without paying proper attention.

■

As the electric front seats can also be adjusted when the ignition is switched off (even when the ignition key is withdrawn), never leave children unattended in the car.

■

The seat backrests must not be angled too far back when driving otherwise this will affect proper operation of the seat belts and of the airbag system – risk of injury!

■

Never carry more people than the number of seats in the vehicle.

Note

■

After a certain time, play can develop within the adjustment mechanism of the

backrest angle.

■

For safety reasons, it is not possible to store the seated position in the seat memory and remote control key memory if the inclination angle of the seat backrest is more than 102° in relation to the seat cushion.

■

Each new driver seat and external mirror position that is saved will overwrite the existing setting.

Seats and Stowage



Manually adjusting the front seats

Electrically adjusting the front seats

Fig. 44 Controls for manual seat adjustment

First read and observe the introductory information and safety warnings



Adjusting a seat in a forward/back direction

Pull the lever A » Fig. 44 in the direction of the arrow 1 and push the seat in

›

the required direction.

The lock must click into place after you release the lever.

Adjusting height of seat

Again push/pull the lever B » Fig. 44 in the direction of one of the arrows 2.

›

Adjusting the angle of the seat backrest

Relieve any pressure from the seat backrest (do not lean on it) and turn the

›

handwheel C » Fig. 44in the direction of the arrow 3.

Adjusting lumbar support

Push the lever D » Fig. 44 in the direction of one of the arrows 4

›

on page 59.

Using the system

Fig. 45 Controls for the electric seat adjustment I

Fig. 46

Controls for the electric seat adjustment II

First read and observe the introductory information and safety warnings on page 59.





Adjusting a seat in a forward/back direction

Push the switch B » Fig. 45 in the direction of one of the arrows 3 » Fig. 46.

›

Set the height of the seat cushion

Push the switch B » Fig. 45 in the direction of one of the arrows 5 » Fig. 46.

›

Adjust the angle of the seat cushion

Push the switch B » Fig. 45 in the direction of one of the arrows 4 » Fig. 46.

›

Adjusting the angle of the seat backrest

Push the switch C » Fig. 45 in the direction of one of the arrows 6 » Fig. 46.

›



Reducing or increasing the curvature of the lumbar support

Push the switch A » Fig. 45 in the region of one of the arrows 2.

›

Raising or lowering the curvature of the lumbar support

Push the switch A » Fig. 45 in the region of one of the arrows 1.

›

The adjusted driver's seat position can be set in the memory of the seat » page 61 or the remote control key » page 61.

Note

If the setting procedure is interrupted, you will need to press the button again.

Memory function of the power seat

Fig. 47

Memory buttons and SET button

Saving front passenger mirror settings when reversing

Switch on the ignition.

›

Press the required memory button B » Fig. 47.

›

Move the rotary knob for the exterior mirror control into position  » page 58.

›

Engage reverse gear.

›

Move the right exterior mirror into the desired position » page 58.

›

Take the vehicle out of gear.

›

The set position of the exterior mirror is stored.

Retrieving the saved setting



Tap the desired memory button B » Fig. 47 when the ignition is switched off

›

and the driver's door is opened.

Press down on the desired memory button B when the ignition is switched on

›

and the driver's door is closed.

Stopping the ongoing adjustment

Press any button on the driver's seat or the button  on the remote control

›

key.

Note

Each time you store the seat and exterior mirror settings for driving forward you also have to re-store the setting of the exterior mirror on the passenger side for reversing.



First read and observe the introductory information and safety warnings

on page 59.

SET

A » Fig. 47.

SET

button, press the desired memory



The memory function for the driver's seat provides the option to store the positions of the driver's seat and the external mirrors. Each of the three memory buttons B » Fig. 47 can be assigned a set position.

Storing seat and exterior mirror settings for driving forward

Switch on the ignition.

›

Adjust the seat to the desired position.

›

Adjust both of the exterior mirrors » page 58.

›

Press the button

›

Within 10 seconds after pressing the

›

button

An acknowledgment sound confirms the storage.

Memory function of the remote control key

First read and observe the introductory information and safety warnings on page 59.



The automatic storage function of the driver's seat and exterior mirrors position when locking the vehicle can be activated in the memory of the remote control

key. When this function is activated, each time the vehicle is locked, the current posi-

tions of the driver's seat and the external mirrors are saved in the memory of the remote control key. After subsequently unlocking the vehicle with the same key, the driver's seat and the exterior mirrors assume the positions stored in the memory of this key.

This function can also be activated/deactivated in the Infotainment » Bedienungsanleitung Infotainment, chapter operating instructions for InfotainmentSetting vehicle systems (CAR button).

Seats and Stowage



Activating the function

Unlock the vehicle with the remote control key.

›

Press and hold any memory button B » Fig. 47 on page 61. After the seat has

›

assumed the position stored under this button, at the same time press the button  on the remote control key within 10 seconds.

The successful activation of the function is confirmed by an audible signal. The seat and exterior mirror settings are not saved in the memory of the key,

which is already saved in the memory button. The seat can be adjusted to the required position if necessary » page 60. After locking the vehicle, the current positions of the driver's seat and the exter-

nal mirrors are saved in the memory of the remote control key.

Deactivating the function

Unlock the vehicle with the remote control key.

›

Press and hold the

›

the button  on the remote control key within 10 seconds.

The successful deactivation of the function is confirmed by an audible signal.

Stopping the ongoing adjustment

Press any button on the driver's seat or the button  on the remote control

›

key.

SET

button A » Fig. 47 on page 61. At the same time, press

Seat heaters

Fig. 48

Heating: Front seats/ rear seats

The seat backrests and surfaces of the front seats and the two outer rear seats can be heated electrically.

The seat heating can only be switched on when the engine is running.

Switching on

Press the button  or  » Fig. 48.

›

By pressing the button once, the heating is switched to the highest intensity level 3, which is indicated by three of the warning lights underneath the switch » Fig. 48 -  or in the button » Fig. 48 -  lighting up.

With repeated pressing of the switch, the level of the seat heating is down-regulated up to the switch-off. The level of the seat heating is indicated by the number of illuminated warning lights underneath/in the switch.

WARNING

If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating. This can lead to burns on the back, the posterior and the legs which are difficult to heal. If the seat heating is used, we recommend to make regular breaks in your journey when driving long distances, so that the body can recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.



CAUTION

■

Do not kneel on the seats or otherwise apply concentrated pressure to them.

■

Do not use the seat heaters if the seats are not occupied by persons or if objects, such as a child seat, bag, etc., are fastened or stored on them. A fault of the heating elements in the seat heating can occur.

■

Do not clean the seats using moisture » page 164, Fabric covers on electrically heated seats.

Note

■

If the on-board voltage drops, the seat heating is switched off automatically, in order to provide sufficient electrical energy for the engine control » page 180, Automatic load deactivation.

■

If the heaters for the rear seats are set to the highest intensity - level 3, they are automatically switched over to level 2 after 10 minutes.



Using the system

Head restraints

WARNING

■

The head restraints must be correctly adjusted in order to offer effective

protection for the occupants in the event of an accident.

■

Never drive with the head restraints removed - risk of injury.

■

If the rear seats are occupied, the rear head restraint must not be in the

lower position.

Note

The middle rear head restraint is only adjustable in two positions.



Fig. 49 Head restraint: front/rear

Setting height

Hold the front head restraints on the sides with both hands, press and hold the

›

safety button A » Fig. 49 and move the head restraints into position. Hold the rear head restraints on the sides with both hands and move them up-

›

wards » Fig. 49.

To move the head restraint downwards, press and hold the safety button 1 with one hand and press the head restraint downwards with the other hand.

Removing/installing

Only the real head restraints may be removed.

Pull the head restraint out of the seat backrest as far as the stop.

›

Press the locking button in the direction of arrow 1 » Fig. 49, simultaneously

›

press the locking button into the opening width of maximum 5 mm and pull out the head restraint. To re-insert the head restraint, push it far enough down into the seat backrest

›

until the locking button clicks into place.

Best protection is achieved if the top edge of the head restraint is at the same level as the upper part of your head.

The head restraints must be adjusted to match the size of the seat occupant. Correctly adjusted head restraints together with the seat belts offer effective protection for the occupants » page 139, Correct seated position.

If the front seats are too far back, we recommend that you have the rear head restraints removed before the seat backrests are folded forward. Store the removed head restraints in such a way that they are not be damaged or soiled.

using a flat screwdriver with a

Rear seats

Seat backrest

Fig. 50

Seat backrest: Locking/unlocking

The luggage compartment can be increased in size by folding the seat backrests forward. The seat backrests can be folded forward individually on vehicles with divided rear seats.

Folding forward

Before folding the seat backrests forwards, adapt the position of the front seats in such a way that they are not damaged by the folded seat backrests 1).

Seats and Stowage



Push the lever A » Fig. 50 and fold the seat backrest completely forwards.

›

Folding backwards

Hold the rear outer seat belt C » Fig. 50 against the side trim panel.

›

Then push the seat backrest back into the upright position until the securing

›

knob A clicks into place – check by pulling on the seat backrest » . Make sure that the red pin B is hidden.

›

WARNING

■

The belts and the belt locks must be in their original position after folding

back the seat backrests – they must be ready to use.

■

The seat backrests must be securely interlocked in position so that no objects in the luggage compartment can slide into the passenger compartment if there is sudden braking – risk of injury.

■

Ensure that the rear seat backrests are properly engaged. It is only then that the three-point seat belt for the middle seat can reliably fulfil its function.

CAUTION

Ensure that the seat belts are not damaged when operating the seat backrests. Under no circumstances must the rear seat belts be jammed by the folded back seat backrests.

Rear armrest

Fig. 51

Rear seats: Armrest

Folding forward

Pull on the loop A » Fig. 51 and fold the arm rest forwards in the direction of

›

the arrow.

A cup holder may be located in the armrest » page 69.

Boot

 Introduction

This chapter contains information on the following subjects: Boot light

Fastening elements 65 Folding double hooks 66 Fixing nets 66 Fixing floor covering of the boot 66 Luggage net 67 Boot cover 67

Please observe the following for the purpose of maintaining good handling characteristics of your vehicle:

Distribute loads as evenly as possible.

›

Place heavy objects as far forward as possible.

›

Attach the items of luggage to the lashing eyes or using the nets » page 65.

›

In the event of an accident, there is such a high kinetic energy which is produced



by small and light objects that they can cause severe injuries. The magnitude of the kinetic energy is dependent on the speed at which the ve-

hicle is travelling and the weight of the object. Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured

object with a weight of 4.5 kg produces an energy, which corresponds to 20 times its own weight. This means that it results in a weight of approx. 90 kg “ ”. You can imagine the injuries that can occur, if this “object” flies through the interior compartment and hits an occupant.

WARNING

■

Store the objects in the luggage compartment and attach them to the lash-

ing eyes.

■

Loose objects can be thrown forward during a sudden manoeuvre or in case

of an accident and can injure the occupants or other road users.

■

Loose objects could hit a deployed airbag and injure occupants - danger of

death!





Using the system

WARNING (Continued)

■

Please note that the handling properties of the vehicle may be affected when transporting heavy objects as the centre of gravity can be displaced – risk of accident! The speed and style of driving must be adjusted accordingly.

■

If the items of luggage or objects are attached to the lashing eyes with unsuitable or damaged lashing straps, injuries can occur in the event of braking manoeuvres or accidents. To prevent items of luggage from moving around, always use suitable lashing straps which must be firmly attached to the lashing eyes.

■

The items carried in the luggage compartment must be stored in such a way that no objects are able to slip forward if any sudden driving or braking manoeuvres are undertaken – risk of injury!

■

When transporting objects in the luggage compartment that has been enlarged by folding the rear seats forward, ensure the safety of the passengers transported on the other rear seats » page 140, Correct seated position for the occupants on the rear seats.

■

Do not drive with the luggage compartment lid fully opened or slightly ajar otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning!

■

Do not exceed the permissible axle loads and permissible gross weight of the vehicle – risk of accident!

■

Do not transport people in the luggage compartment!

CAUTION

Make sure that transported objects with sharp edges do not damage the following:

■

heating elements in the rear window;

■

Elements of the aerial integrated in the rear window.

Note

Tyre pressure must be adjusted to the load

» page 182, Tyre life.

Note

If the boot lid is open and the ignition switched off, the light will extinguish automatically after around 10 minutes.

Fastening elements

Fig. 52

Luggage compartment: Lashing eyes and fastening elements

First read and observe the introductory information and safety warnings



The boot provides the following fastening elements » Fig. 52.

Lashing eyes for fastening items of luggage and fixing nets.

Fastening elements and eyes for fastening fixing nets.

on page 64.

CAUTION

The maximum permissible load of the lashing eyes A is 3.5 kN (350 kg).

Note

The upper front lashing eye is located underneath the folding rear seat backrest.



Boot light

First read and observe the introductory information and safety warnings on page 64.



The light switches on/off when the boot lid is opened or closed.

Seats and Stowage

Folding double hooks

Fig. 53

Luggage compartment: Folding double hooks

First read and observe the introductory information and safety warnings on page 64.



The folding double hook is used to affix small items of luggage, e.g. bags. The folding double hook can be located on either of the two sides of the luggage

compartment, according to the model.

CAUTION

An item of luggage with a maximum weight of 5 kg can be attached to each side of the double hook.

Fixing nets

Fig. 54

Example for fixing nets

First read and observe the introductory information and safety warnings on page 64.



Examples for attaching the fixing nets» Fig. 54.

Horizontal pocket

Floor net

Vertical pocket

WARNING

Do not exceed the maximum permissible load of the fixing nets. Heavy objects are not secured sufficiently – risk of injury!

CAUTION

■

The maximum permissible load of the fixing nets is 1.5 kg.

■

Do not place any sharp objects in the nets – risk of damaging the net.

Fixing floor covering of the boot

Fig. 55



First read and observe the introductory information and safety warnings on page 64.



A loop is located on the floor covering of the boot. When handling the spare wheel, for example, you can raise the floor covering and

fix it to a hook at the luggage compartment cover using the loop » Fig. 55.

Luggage compartment: fixing the floor covering



Using the system

Luggage net

Boot cover

Fig. 56

Luggage compartment: Luggage net

First read and observe the introductory information and safety warnings on page 64.



The luggage net is located on the underside of the luggage compartment cover. The net is designed for transporting lighter objects.

WARNING

Only store soft objects with a total weight of 1.5 kg in the net. Heavy objects are not secured sufficiently – risk of injury!

CAUTION

No objects with sharp edges should be stored in the luggage net, as they can damage the luggage net.

Fig. 57 Removing/installing the luggage compartment cover

Fig. 58

Luggage compartment cover stowed behind the rear seats



First read and observe the introductory information and safety warnings



Removing

Unhook the support straps 1 » Fig. 57.

›

On the underside of the cover, in the area between the holders, press 2.

›

Remove the cover.

›

Install

Place the cover on the contact surfaces of the side trim panel.

›

The mounts of the cover 3 » Fig. 57 must be positioned above the holders

›

of the side trim panel. Press on the upper side of the cover so that the mounts fully interlock in the

›

holders. Hook the support straps 1 on the boot lid.

›

The removed boot cover can be stowed behind the seat backrest » Fig. 58.

on page 64.

Seats and Stowage



WARNING

No objects should be placed on the luggage compartment cover, the vehicle occupants could be endangered if there is sudden braking or the vehicle collides with something.

CAUTION

■

Please ensure that the heating elements for the rear window heater are not

damaged as a result of objects placed in this area.

■

When closing the boot lid, jamming and damage to the luggage compartment cover or the side trim panel can occur if handled in an unprofessional way. The following guidelines must be observed.

■

The mounts of the cover 3 » Fig. 57 must be interlocked in the holders of the

side trim panel 2.

■

The items which are transported must not exceed the height of the luggage

compartment cover.

■

The cover must not be jammed in the seal of the boot lid when it is in the

opened position.

■

There must be no object in the gap between the opened cover and the rear

backrest.

Note

Opening the boot lid also lifts up the boot cover.

Roof rack system

Introduction



This chapter contains information on the following subjects: Attachment points

Roof load

WARNING

■

The items which you transport on the roof bar system must be reliably at-

tached – risk of accident!

■

Always secure the load with appropriate and undamaged lashing straps or

tensioning straps.

■

Distribute the load evenly over the roof rack system.

■

When transporting heavy objects or objects which take up a large area on the roof rack system, the handling of the car may change as a result of the displacement of the centre of gravity. The style of driving and speed must therefore be adapted to the current circumstances.

■

Avoid abrupt and sudden driving/braking manoeuvres.

■

Adjust the speed and driving style to the visibility, weather, road and traffic conditions.

■

The permissible roof load, permissible axle loads and gross permissible weight of your vehicle must not be exceeded under any circumstances – risk of accident!

CAUTION

■

Only use roof rack systems approved by ŠKODA.

■

If other roof rack systems are used or if the roof bars are not fitted correctly,

any resulting damage to the vehicle is not covered by the warranty. Therefore observe the supplied fitting instructions for the roof rack system are observed.



■

On models fitted with a sliding/tilting roof, ensure that the sliding/tilting roof

does not strike any items of luggage transported on the roof.

■

Ensure that the luggage compartment lid does not hit the roof load when

opened.

■

The height of the vehicle changes after mounting a roof luggage rack system

and the load that is secured to it. Compare the vehicle height with available clearances, such as underpasses and garage doors.

■

Always remove the roof luggage rack system before entering an automated car

wash.

■

69 69

Ensure the roof aerial is not impaired by the secured load.

For the sake of the environment

The increased aerodynamic drag results in a higher fuel consumption.



Using the system

Attachment points

Cup holder

Fig. 59 Attachment points for roof bars

First read and observe the introductory information and safety warnings



Installation location of the attachment points for roof bars » Fig. 59:

Front attachment points

Rear attachment points

Perform the assembly and disassembly according to the enclosed instructions.

on page 68.

CAUTION

Observe the information regarding the assembly and disassembly in the enclosed instructions.

Roof load

First read and observe the introductory information and safety warnings on page 68.



The maximum permissible roof load (including roof rack system) of 75 kg and the maximum permissible total weight of the vehicle should not be exceeded.

The full permissible roof load cannot be used if a roof rack system with a lower load carrying capacity is used. In this case, the roof rack system must only be loaded up to the maximum weight limit specified in the fitting instructions.

Fig. 60 Cup holder: in the front centre console/in the rear armrest

Two beverage containers can be placed into the cup holders/recesses.

Cup holder in front centre console

Cup holder in rear armrest

Removable element

You can change the size of the individual openings using the removable elements

and D.

WARNING



■

Never put hot beverage containers in the cup holder. If the vehicle moves,

they may spill – risk of scalding!

■

Do not use any cups or beakers which are made of brittle material (e.g. glass,

porcelain). This could lead to injuries in the event of an accident.

CAUTION

Do not leave open beverage containers in the cup holder during the journey.

There is a risk of spilling e.g. when braking which may cause damage to the elec-

trical components or seat upholstery.



Seats and Stowage



Ashtray

Cigarette lighter

Fig. 62

Centre console: Cigarette lighter

Fig. 61 Centre console: Ashtray at the front/rear

Removing/inserting the front ash tray

Pull out the ashtray » Fig. 61 -  in the direction of the arrow.

›

Insertion takes place in the reverse order.

Removing/inserting the rear ashtray insert

Opening the stowage compartment » page 77.

›

Grasp the insert in the area marked with the arrows and remove it in the direc-

›

tion of the arrow

Insertion takes place in the reverse order.

» Fig. 61 - .

WARNING

Never place flammable objects in the ashtray – risk of fire!

CAUTION

When removing do not hold the ashtray at the cover on the front– risk of breakage.

Using the system

Press in the button of the cigarette lighter » Fig. 62.

›

Wait until the button pops forward.

›

Remove the cigarette lighter immediately and use.

›

Place the cigarette lighter back into the socket.

›

WARNING

■

Take care when using the cigarette lighter! Improper usage can case burns.

■

The cigarette lighter also operates when the ignition is switched off or the ignition key withdrawn. Therefore never leave children unattended in the vehicle.

Note

Further information » page 165, Accessories, changes and replacement of parts.



Sockets

12-Volt power socket

Fig. 63 12-Volt power socket: in the front centre console/ in the boot

Overview of the 12-volt power socket

In the front centre console » Fig. 63 - . In the boot » Fig. 63 - .

Use of the 12-volt power socket

Remove the cover on the power socket and open the cover on the power sock-

›

et. Connect the plug for the electrical appliance to the socket.

›

The 12-volt power sockets and any connected appliances can also be operated when the ignition is switched off or the ignition key is withdrawn » .

CAUTION

■

The power socket can only be used for connecting approved electrical accesso-

ries with a total power uptake of up to 120 watt.

■

Never exceed the maximum power consumption, otherwise the vehicle's elec-

trical system can be damaged.

■

Connecting appliances when the engine is not running will drain the battery of

the vehicle!

■

Only use matching plugs to avoid damaging the power sockets.

■

Only use accessories that have been tested for electromagnetic compatibility in

accordance with the applicable directives.

■

Switch off the devices connected to the power sockets before you switch the ignition on or off and before starting the engine, to avoid damage from voltage fluctuations.

■

Observe the operating instructions for the connected devices!

230-Volt power socket

Fig. 64

Centre console at rear: 230-Volt power socket



WARNING

■

Improper use of the power sockets and the electrical accessories can cause

fires, burns and other serious injuries.

■

Never leave children unattended in the vehicle.

■

If the connected electric device becomes too hot, switch it off and discon-

nect it from the power supply immediately.

Use

Fold out the lid on the power socket in the direction of the arrow

›

Connect the plug for the electrical appliance to the socket.

›

The 230-Volt power socket can only be used when the ignition is switched on » .

When the plug on the electrical appliance is inserted into the power socket, the child safety lock is released, and the power socket is activated.

LED display

Permanent green light: The power socket is activated.

›

Flashing red light: The power socket is temporarily deactivated.

›

Seats and Stowage

» Fig. 64.



The power socket is deactivated automatically when the amperage is too high, the temperature is too high or the battery charge state is too low.

When the reasons for the deactivation no longer apply, the power socket will be re-activated automatically. Then re-activate connected devices which are switched on » .

WARNING

■

The power socket can only be used for connecting approved electrical accessories with a two-pin 230V plug, with a total power uptake of up to 150 watt.

■

The power sockets- and thus the connected electrical devices -only operates if the ignition is switched on!

■

Improper use can lead to serious injury or fire. Therefore never leave children unattended in the vehicle - risk of injury!

■

Safely stow away all connected devices during the journey to prevent them from being thrown around the interior in the event of a sudden braking manoeuvre or an accident - risk of death!

■

Do not pour liquids into the power socket - risk of death! If fluid does manage to get into the power socket, completely dry out the socket before reuse.

■

The connected appliances may behave differently to when connected to the mains.

■

The connected devices may warm up during operation - risk of injury or fire!

■

The child lock on the 230 Volt power socket is unlocked when using energised adapters and extension cables - risk of injury!

■

Do no insert any conductive objects into the contacts of the power socket, e.g knitting needs - risk of death!

CAUTION

■

Place the connector on the electrical device into the power socket as far as it

can go to create a connection between the contacts.

■

If the connector of the electrical device is not inserted fully into the power sock-

et, the child safety lock might release, and the power socket be activated. The electrical device is nevertheless not connected.

■

On vehicles with the START STOP system, when starting up the engine, the 230

Volt power socket is temporarily deactivated and the LED display flashes red. After starting the engine, the power socket is re-activated automatically.

■

Do not connect any lamps with neon filaments to the 230 V power socket - risk

of damaging the lamp.

■

A larger current surge may arise in some power supplies (e.g. for notebooks) when connecting them to a 230 V power socket- this will automatically deactivate the power socket. In this case, disconnect the power supply from the consumer and connect the power supply to the power socket first, followed by the consumer.

■

Observe the operating instructions for the connected devices!

Storage compartments

Overview

The vehicle has the following storage compartments:

Storage compartment on the front passenger side » page 73 Storage compartment on the driver's side » page 73 Holder for reflex vest » page 74 Stowage compartment in front centre console » page 74 Multimedia holder » page 74 Map pockets in the front seats » page 75 Glasses storage box » page 75 Storage compartments in the doors » page 75 Stowage compartment below front passenger seat » page 76 Front armrest with storage compartment » page 76 Stowage compartment in rear centre console » page 77 Seat backrest with through-loading channel » page 77 Removable through-loading bag » page 77 Storage compartment in the boot » page 78 Storage box underneath the luggage compartment cov-

» page 79





Using the system

WARNING

■

Do not place anything on the dash panel. These objects might slide or fall down when driving (when accelerating or cornering) and may distract you from concentrating on the traffic - risk of accident!

■

When driving, ensure that no objects from the centre console or from other storage compartments can get into the driver's footwell. You would then no longer be able to apply the brakes, operate the clutch or accelerator – risk of accident!

Storage compartment on the front passenger side

Dash panel: Open storage compartment/control cooling of storage

Fig. 65

compartment

A pen and credit card holder is provided in the stowage compartment.

Open/close

Pull the handle of the flap in the direction of the arrow » Fig. 65 –  and fold

›

down the flap. Lift the lid upwards until it clicks into place.

›

Cooling

Use the rotary switch » Fig. 65 –  to open/close the air supply.

›

Opening the air supply when the air conditioning system is switched on allows cooled air to flow into the storage compartment.

Opening the air inlet when the air conditioning system is on causes fresh or interior air to flow into the storage compartment.

We recommend closing the air supply if it is operated in heating mode or the cooling system for the storage compartment is not being used.

WARNING

The storage compartment must always be closed when driving for safety reasons.



Note

When the stowage compartment is opened, a light lights up.

Storage compartment on the driver's side

Fig. 66

Dash panel: Storage compartment on the driver's side

Open/close

Raise the handle A » Fig. 66 and open out the compartment in the direction of

›

the arrow. Swivel the lid against the direction of the arrow until it clicks into place.

›

WARNING

The storage compartment must always be closed when driving for safety reasons.



Seats and Stowage

Holder for reflex vest

Fig. 67

Driver seat: Holder for reflex vest

Closing takes place in the reverse order.

The phone box may be located in the stowage compartment » page 135.

WARNING

The storage compartment is not a substitute for the ashtray and must also not be used for such purposes - risk of fire!

Multimedia holder



The holder for the reflex vest is located under the driver's seat » Fig. 67.

WARNING

Do not put anything else except for the reflex vest into the holder- otherwise it may fall out of the holder - risk of obstruction or limitation in operating the pedal!

CAUTION

Do not put anything else except for the reflex vest into the holder- risk of damage to the holder.

Stowage compartment in front centre console

Fig. 68

Front centre console: Stowage compartment

Open/close

Press on the edge of the roof A » Fig. 68 in the direction of the arrow.

›

Using the system

Fig. 69

Front centre console: Multimedia holder

The multimedia holder is located in the front centre console » Fig. 69. You can use this holder to store e.g. a mobile phone, MP3 player or similar devi-



ces.

WARNING

Never use the holder as an ashtray or for storing flammable objects – risk of fire!



Map pockets in the front seats

Swivel the lid on the glasses storage box against the direction of the arrow until

›

it is heard to lock.

Fig. 70

Front seat rests: Map pockets

The pockets intended for storage of maps, magazines, etc. are provided on the reverse side of the front seat rests » Fig. 70.

WARNING

Never put heavy items in the map pockets – risk of injury!

CAUTION

Do not put any large items (such as bottles) or sharp objects into the map pockets, as the pockets and the seat covers could be damaged.

Glasses storage box

Fig. 71

Roof trim: Glasses storage box

WARNING

■

The compartment must only be opened when removing or inserting the

spectacles and otherwise must be kept closed!

■

The compartment must be closed before leaving and locking the vehicle -

risk of impairment to the functions of the anti-theft alarm system!

CAUTION

Do not put any heat-sensitive objects in the glasses storage box – they may be damaged.

Storage compartments in the doors



Storage compartment: in the front door/in the rear door

Fig. 72

The area B » Fig. 72 and D has a bottle holder.

WARNING

Use the area A » Fig. 72 of the storage compartment only for storing objects which do not project so that the effectiveness of the side airbag is not impaired.



Open/close

Press on the cover of the glasses storage box in the area A » Fig. 71. The com-

›

partment folds in the direction of the arrow.

Note

In area with a max. content of 1 l.

of the stowage compartment of the rear doors, a bottle can be housed

Seats and Stowage



Stowage compartment below front passenger seat

Fig. 73

Front passenger seat: Stowage compartment

Front armrest with storage compartment

Open/close

Pull the handle to position 1 » Fig. 73. The compartment opens out in the di-

›

rection of the arrow When closing the compartment, hold the handle until the compartment is

›

closed.

WARNING

The storage compartment must always be closed when driving for safety reasons.

CAUTION

The storage compartment is designed for storing small objects of up to 1.5 kg. in weight.

Using the system

Fig. 74 Armrest: Stowage compartment

The armrest is adjustable for height and length.

Opening/closing the cover of the stowage compartment

Pull and open the cover of the armrest using the handle A in the direction of

›

the arrow Open the lid to the stop, only then can it be folded downwards and against the

›

direction of the arrow 1.

Adjusting the height of the armrest

First of all fold the cover downwards and then lift it in the direction of the arrow

›

Adjusting the length of the armrest

Move the lid into the desired position in the direction of the arrow 2 » Fig. 74.



›

The area objects with a maximum size of 98 mm x 104 mm x 142 mm.

The area C of the stowage compartment is designed for the storage of smaller objects.

» Fig. 74.

» Fig. 74 into one of the 4 fixed positions.

» Fig. 74 of the stowage compartment is designed for the storage of

Note

Push the armrest cover all the way back to the stop before applying the handbrake.



Stowage compartment in rear centre console

Fig. 75

Centre console at rear: Stowage compartment

The storage compartment is equipped with a removable insert.

Open/close

Pull the handle A » Fig. 75 on the upper section of the recess and open out the

›

compartment in the direction of the arrow.

Closing takes place in the reverse order.

WARNING

The storage compartment is not a substitute for the ashtray and must also not be used for such purposes - risk of fire!

After folding the rear armrest and cover up, an opening in the seat backrest becomes visible through which the removable through-loading bag with skis can be pushed. The armrest and cover can be folded forward from the passenger compartment or the boot.

Opening from the passenger compartment

Fold the rear armrest dow (not as far as the stop) » page 64.

›

Pull the handle A » Fig. 76 in the direction of the arrow and fold the cover

›

downwards.

Opening from the boot

Push the unlock button B » Fig. 76 in the direction of the arrow and fold the

›

cover including the armrest forwards.

Closing

Fold the cover and rear armrest upwards to the stop - the cover must click into

›

place.

Ensure that the armrest is always locked into place after closing. This is apparent as the red field above the unlocking button boot.

» Fig. 76 is not visible from the

WARNING

The through-loading channel is only intended for transporting skis that are



placed in a properly secured, removable through-loading bag » page 77.



Seat backrest with through-loading channel

Fig. 76

Rear seats: Cover handle/boot: Unlock button

Through-loading bag

Fig. 77

Securing the through-loading bag

The removable through-loading bag is solely used for transporting skis.

Seats and Stowage



Open the luggage compartment lid.

›

Fold the rear armrest and the cover in the seat backrest downwards » page 77.

›

Place the empty, removable through-loading bag in such a way that the end of

›

the bag with the zip is in the boot. Push the skis into the removable through-loading bag from the boot » .

›

Close the through-loading bag.

›

Securing

Tighten the strap

›

ings » Fig. 77. Fold the seat backrest a little forward.

›

Guide the securing strap B through the opening in the seat backrest around

›

the upper part of the seat backrest. Then push the seat backrest back into the upright position until the unlocking

›

button clicks into place - check by pulling on the seat backrest. Insert the securing strap B into the lock C until it clicks into place.

›

on the free end around the skis in front of the bind-

WARNING

■

After placing skis into the through-loading bag, you must secure the bag

with the securing strap B » Fig. 77.

■

The strap A must hold the skis tight.

■

Make sure that the strap A holds the skis in front of the binding (also refer

to imprint on the removable through-loading bag).

■

The total weight of the skis which are transported must not exceed 17 kg.

Note

■

The through-loading bag is foreseen for four pairs of skis.

■

Place the skis and sticks in the removable through-loading bag with the tips

facing to the rear.

■

If there are several pairs of skis in the removable through-loading bag, ensure

that the bindings are positioned at the same height.

■

The removable through-loading bag must never be folded together or stowed

when moist.

Storage compartment in the boot

Fig. 78 Luggage compartment: Stowage compartment/example of attaching an item of luggage using the cargo element

Increasing the size of the boot

Remove the cover of the stowage compartment 1 in the direction of the ar-

›

row » Fig. 78.

Securing items of luggage

Remove the cargo element (a part of the cover of the stowage compartment)

›

» Fig. 78 and attach to the floor covering of the luggage compartment with

the Velcro fastener.

The stowage compartment can be located on either of the two sides of the luggage compartment, according to the model.

CAUTION

■

The storage compartment is designed for storing small objects of up to 2.5 kg.

in weight in total.

■

The cargo element is designed for attaching objects with a maximum gross

weight of 8 kg.

■

When using the storage compartment, take care not to damage it or the lug-

gage compartment lining.



Note

We recommend you use the cargo element to secure items of luggage behind the rear seats.



Using the system

Storage box underneath the luggage compartment cover

Insert the catches on the lateral carrier rail underneath the front edge of the

›

box 1 in the direction of the arrow » Fig. 80. Secure the other side of the lateral carrier rail in the hole 2 the direction of the

›

arrow.

Removal is carried out in the reverse order.

CAUTION

■

The maximum permissible load of the storage box is 2.5 kg.

■

Prevent objects stored in the storage box from slipping at all times using the

lateral carrier rails.



Fig. 79 Storage box: inserted/removed

Fig. 80

Storage box: Insert lateral carrier rail

The storage box can be divided up using two lateral carrier rails A » Fig. 79.

Inserting/removing the box

Remove the box with box hands in the direction of the arrow 1 » Fig. 79 as far as

›

the stop

Insertion takes place in the reverse order.

Removing/inserting the box

Remove the box with both hands in the direction of the arrow 2 » Fig. 79 after

›

passing the stop B.

Insertion takes place in the reverse order.

Inserting/removal lateral carrier rails

You can insert/remove the later carrier rails when the box has been removed as far as the stop

» Fig. 79.

Clothes hooks

The clothes hooks are located at the centre door bars of the vehicle.

WARNING

■

Ensure that any clothes hanging from the hooks do not impair your vision to

the rear.

■

Only use the hooks for hanging light items of clothing and ensure that there

are no heavy or sharp-edged objects in the pockets.

■

Do not use clothes hangers for hanging up items of clothing otherwise this

may reduce the effectiveness of head airbags.

CAUTION

The maximum permissible load of the hooks is 2 kg.

Seats and Stowage



Parking ticket holder

Fig. 81

Windscreen: Parking ticket holder

The note holder is designed e.g. for attaching car park tickets.

WARNING

The attached note has to always be removed before starting off in order not to restrict the driver's vision.



Using the system

Heating and air conditioning system

Introductory information

The heating effect is dependent upon the coolant temperature, thus full heat output only occurs when the engine has reached its operating temperature.

If the cooling system is switched on, the temperature and air humidity drops in the vehicle. The well-being of the occupants of the car is enhanced as a result of this particularly at high outside temperatures and a high air humidity. The system prevents the windows misting up during the cold season of the year.

It is possible to briefly activate recirculated air mode to enhance the cooling effect.

Please refer to the information regarding recirculated air mode for the air-conditioning system » page 85 or for Climatronic » page 87.

The air inlet in front of the windscreen must be free of e.g. ice, snow or leaves to ensure that the heating and cooling system operates properly.

After switching on the cooling Condensation from the evaporator of the air conditioning may drip down and form a puddle below the vehicle. This is not a leak!

WARNING

For your own safety and that of other road users, ensure that all the windows are free of ice, snow and misting. Please familiarize yourself about how to correctly operate the heating and ventilation systems, how to demist and defrost the windows, as well as with the cooling mode.

Note

■

The used air streams out through the vents in the luggage compartment.

■

We recommend that you do not smoke in the vehicle when the recirculating air

mode is operating since the smoke which is drawn at the evaporator from the interior of the vehicle forms deposits in the evaporator of the air conditioning system. This produces a permanent odour when the air conditioning system is operating which can only be eliminated through considerable effort and expense (replacement of compressor).

Using the air conditioning system economically

The compressor on the air conditioning system uses power from the engine when in cooling mode which will effect the fuel consumption.

It recommended to open the windows or the doors of a vehicle for which the interior has been strongly heated through the effect of direct sunlight in order to allow the heated air to escape.

The cooling system should not be switched on while travelling when the window is open.

For the sake of the environment

Pollutant emissions are also reduced when fuel is saved » page 101, Economical and environmentally friendly driving.

Operational problems

If the cooling system does not operate at outside temperatures higher than +5 °C, there is a problem in the system. The reasons for this may be.

One of the fuses has blown. Check the fuse and replace if necessa-

›

ry » page 200. The cooling system has switched off automatically for a short time because the

›

coolant temperature of the engine is too hot » page 10.

If you are not able to resolve the operational fault yourself, or if the cooler output has reduced, switch off the cooling system and get assistance from a ŠKODA Specialist garage.



Heating and air conditioning system

Air outlets

Air vents at the front

Fig. 82

Fig. 83

Air vents at the rear

Open/close

Turn the wheel B » Fig. 82 or » Fig. 83 upwards or downwards.

›

Changing the direction of air flow

Swivel the fins A » Fig. 82 or » Fig. 83 vertically or horizontally.

›

An overview of the available settings for adjusting the direction of the air outlet

Setting of the control dial Active air outlet vents











If the air distribution is positioned towards the windows, no air will be fed to the footwell. This can lead to restriction of the heating comfort.

1, 2, 4

1, 2, 4, 5, 7

2, 3, 4, 6

2, 4, 5, 7

2, 3, 4, 5, 6, 7

Note

Do not cover the air outlet vents with any objects, of any kind.



Warmed, unwarmed or cooled air will flow out of the air outlet vents according to the setting of the regulator of the heating or the air conditioning system and the atmospheric conditions.

The direction of airflow can be adjusted using the air outlet vents 3, 4 » Fig. 82 and 6 » Fig. 83 - the outlets can be opened and closed individually.

Using the system

Heating

Control elements

Fig. 84 Heating: Control elements

Functions of the individual controls » Fig. 84:





The blower should always be on to prevent the windows from misting up.

Adjusting

Recommended basic settings of the heating controls for the respective operating modes:

Set-up

Defrosting the windscreen and side windows

Free windscreen and side windows from mist

Rapid heating

Comfortable heating Desired temperature 2-4

Fresh air mode – ventilation

Warmer air is directed to the footwell than to the upper part of the body.

Setting of the control dial » Fig. 84 on page 83

A B C

To the right up to the

stop

Desired temperature 3-5

To the right up to the

stop

To the left up to the

stop

4-5

1-6

  

Set the temperature (turn to the left: Turn to the right to reduce the temperature: increase temperature)

Set the blower stage (stage 0: Blower off, stage 6: the highest blower stage)

Set the direction of the air outlet » page 82 Switch the rear window heater on/off » page 52 Open/close the fresh air supply » page 84

Air outlet vents 4 » Fig. 82 on

page 82

Open and align with the side win-

dow

Open and align with the side win-

dow











Button

Do not switch on

Briefly switch on Opening

Do not switch on Opening





Heating and air conditioning system

We recommend that you leave the air outlet vents 3 » Fig. 82 on page 82 in the opened position.

If the desired interior temperature can also be achieved without activating the



cooling system, fresh air mode should be selected.

Recirculated air mode

Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the button  and the warning light underneath the button illuminates.

›

Press the button  again, the warning light underneath the button goes out.

›

Recirculated air mode is switched off automatically if the air distribution control

» Fig. 84 on page 83 is turned to position . Recirculated air mode can be

switched on again from this setting by repeatedly pressing the button .

WARNING

Do not leave recirculated air mode on over a longer period of time, as “stale” air can cause fatigue of the driver and passengers, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases. Switch off recirculated air mode as soon as the windows start to mist up.

Air conditioning system (manual air conditioning system)

Introductory information

The cooling system only operates if the button ed, and the following conditions are met:

engine running;

›

outside temperature above approx. 2 ℃;

›

blower switch switched on (positions 1-6).

›

Under certain circumstances, air at a temperature of about 5 °C can flow out of the vents when the cooling system is switched on. Lengthy and uneven distribution of the air flow out of the vents and large differences in temperature, for example when getting out of the vehicle, can result in chills in sensitive persons.



» Fig. 85 on page 84 is press-

Note

We recommend that you have the air conditioning system cleaned by a ŠKODA specialist garage once every year.

Control elements



Fig. 85

Air conditioning: Control elements

Functions of the individual controls » Fig. 85:

Set the temperature (turn to the left: Turn to the right to reduce the temperature: increase temperature)

Set the blower stage (stage 0: Blower off, stage 6: the highest blower stage)

Set the direction of the air outlet » page 82

Depending on equipment: Switch the windscreen heater on/off Switch the auxiliary heating on/off



Switch the cooling system on/off (The indicator light in or underneath the button lights up/goes out)



Switch the rear window heater on/off » page 52



Open/close the fresh air supply » page 85



» page 52



» page 89





Using the system

Note

The warning light in the button conditions for the function of the cooling system have been met » page 84, Intro- ductory information. By lighting up of the warning light in the button, the operational readiness of the cooling system is signalled.



lights after activation, even if not all of the



Setting the air conditioning system

Recommended basic settings of the control elements of the air conditioning system for the respective operating modes:

Set-up

Defrost/defog windscreen and side windows

Rapid heating

Comfortable heating

Rapid cooling

Comfortable cooling

Fresh air mode – ventilation

We recommend that you do not use this setting in countries with high humidity levels. This can result in heavy cooling of the window glass and the following fogging from outside.

Automatic activation can be switched off by pressing the button

Automatic activation can be switched off by pressing the button  » Fig. 85 on page 84.

Warmer air is directed to the footwell than to the upper part of the body.

We recommend that you leave the air outlet vents 3 » Fig. 82 on page 82 in the opened position.

Setting of the control dial » Fig. 85 on page 84 Button » Fig. 85 on page 84

A B C

Desired tempera-

ture

To the right up to

the stop

Desired tempera-

ture

To the left up to

the stop

Desired tempera-

ture

To the left up to

the stop

4-6

1-4

briefly 6, then 2 -

1-3

Desired position



» Fig. 85 on page 84.





  

      



Recirculated air mode

Recirculated air mode prevents polluted air outside the vehicle from getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the button  and the warning light underneath the button illuminates.

›

 

Automatically switched on

Switched off Briefly switch on Opening

Switched off Do not switch on Opening

Activated

Activated Do not switch on Opening

Switched off Do not switch on Opening

Do not switch on

Automatically switched

Air outlet vents 4 » Fig. 82

on page 82

Open and align with the side

window

Opening



Heating and air conditioning system

Press the button  again, the warning light underneath the button goes out.

›

Recirculated air mode is switched off automatically if the air distribution control

» Fig. 85 on page 84 is turned to position . Recirculated air mode can be

switched on again from this setting by repeatedly pressing the button .

WARNING

Climatronic (automatic air conditioning system)

Control elements



Introductory information

The Climatronic in automatic mode ensures the best-possible setting of the temperature of the outflowing air, the blower stage and air distribution.

The system also takes sunlight into account, which eliminates the need to alter the settings manually.

Recommended setting for all periods of the year:

Set the desired temperature, we recommend 22 °C.

›

Press the button

›

Move the air outlet vents 3 and 4 » Fig. 82 on page 82 so that the air flow is

›

directed slightly upwards.

Cooling conditions

The cooling system only operates if the following conditions are met:

engine running;

›

outside temperature above approx. +2 °C;

›



» Fig. 86 on page 86 switched on.

›

The AC compressor is switched off at a high coolant temperature in order to provide cooling at a high load of the engine.

Using the system

AUTO

» Fig. 86 on page 86.

Fig. 86 Climatronic: Control elements

Functions of the individual controls » Fig. 86:

Adjust the temperature for the left side or for both sides » page 87

Adjust the blower speed » page 88

Adjust the temperature for the right side » page 87

Display the temperature setting for the left side

Display the temperature setting for the right side

Depending on equipment: Switch the auxiliary heating on/off Switching off Climatronic



Control the seat heater on the front left seat » page 62



Air flow to the windows



Air flow to the upper body



Air flow in the footwell



Switch automatic air distribution control on/off » page 87





Control the seat heater on the front right seat » page 62



Switch the intensive windscreen heater on/off » page 88



Switch the rear window heater on/off » page 52



Switch the windscreen heater on/off » page 52

SETUP

Adjust Climatronic in the Infotainment

DUAL

Switch the temperature setting in Dual mode on/off » page 87

OFF



» page 89



AUTO

Switch automatic mode on/off » page 87



Switch the cooling system on/off » page 87

Note

The interior temperature sensor is located between the buttons  and Do not stick anything on or cover the sensor, otherwise it could have an unfavourable effect on the Climatronic.

SETUP

Automatic mode

Automatic mode works in three modes - weak, medium, and intensive. Information on the setting » Bedienungsanleitung Infotainment, chapter Addi-

tional functions (CAR button).

Switching on

Set the temperature between +16 °C and +29 °C using the control dials A and

›

» Fig. 86 on page 86.

Press the button

›

Switching off

Press any button for the air distribution or increase/reduce the blower speed.

›

After the Climatronic is switched on, it works in the last selected mode. The currently selected mode is displayed in the Infotainment display. Climatronic is set to the medium setting by default.

AUTO

and the indicator light in the button illuminates.

Note

We recommend that you adjust the air outlet vents 3 and 4 » Fig. 82 on page 82, so that the air flow is directed slightly upwards.

Switch cooling system on/off

Press the button

›

Pressing the button

›

light in the button goes out.

After the cooling system is switched off, only the ventilation function remains active whereby the minimum temperature that can be reached is the outside temperature.



and the indicator light in the button illuminates.



again switches off the cooling system - the indicator

Setting temperature

The interior temperature for the left and right side can be set separately or together.

For both sides

Turn the control dial A » Fig. 86 on page 86 to the left or right to increase or

›



decrease the temperature.

The warning light in the button

For the right side

Turn the control dial C » Fig. 86 on page 86 to the left or right to increase or

›

decrease the temperature.

The indicator light lights up in the

If the indicator light in the button sides cannot be set with the control dial A. This function can be restored by pressing the button

The interior temperature can be set between +16 ℃ and +29 ℃. The interior temperature is regulated automatically within this range.

If a temperature lower than +16 ℃ is selected, a blue symbol lights up on the control dial.

If a temperature higher than +29 ℃ is selected, a red symbol lights up on the control dial.

At both end positions, Climatronic runs at maximum cooling/heating output and the temperature is automatically not regulated.

DUAL

goes out.

DUAL

button.

DUAL

is illuminated, the temperature for both

. The warning light in the button goes out.

CAUTION



Lengthy and uneven distribution of the air flow out of the vents (especially around the feet) and large differences in temperature, for example, when getting out of the vehicle, can cause susceptible individuals to catch a cold.

Automatic recirculated air mode

Recirculated air mode largely prevents polluted air from outside the vehicle getting into the vehicle, for example, when driving through a tunnel or when standing in a traffic jam.





Heating and air conditioning system

If a considerable increase in concentration of pollutants is recognised by the air quality sensor, recirculated air mode will temporarily be switched off.

If the concentration of pollutants decreases to the normal level, the air distribution control is automatically switched off so that fresh air can be guided into the vehicle interior.

In recirculated air mode air is sucked out of the interior of the vehicle and then fed back into the interior. When the automatic air distribution control is switched on, an air quality sensor measures the concentration of pollutants in the drawn in air.

If the air quality sensor does not switch on automatic recirculated air mode when there is an unpleasant smell, you can switch in on manually.

Switching on/off

Press the button  and the warning light underneath the button illuminates.

›

Press the button  again, the warning light underneath the button goes out,

›

where necessary press the button

You can also switch the system on/off in he Infotainment » Bedienungsanleitung Infotainment, chapter Setting vehicle systems (CAR button).

AUTO

WARNING

Note

■

If the windscreen mists up, press the button . Press the button

the windscreen is demisted.

■

The automatic air distribution control operates only if the outside temperature

is higher than approx. 2 °C.

AUTO

when

Controlling blower

The blower stage can be manually adapted to suit your particular needs.

Turn the control dial B » Fig. 86 on page 86 to the left or right to increase or

›

decrease the blower speed.

If the blower speed is reduced to a minimum, Climatronic is switched off.

The set blower speed is displayed in the control dial ber of warning lights come on.

when the respective num-

WARNING

■

“Stale air” may result in fatigue in the driver and occupants, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases.

■

Do not switch off the Climatronic system for longer than necessary.

■

Switch on the Climatronic system as soon as the windows mist up.

Defrosting windscreen

Switching on/off

Press the button  » Fig. 86 on page 86.

›

Press the button  or the button

›

More air flows out of the air outlet vents 1 » Fig. 82 on page 82. The temperature control is controlled automatically.

AUTO

again.

Auxiliary heating (auxiliary heating and ventilation)



Introduction

This chapter contains information on the following subjects: Switching on/off

setting Remote control 90 Replacing the battery in the remote control



Function prerequisites when switching on:

Comfort temperature has been set;

›

The blower is switched on;

›

the air outlet vents are opened;

›

The air outlet is set to position  or .

›

Auxiliary heating (parking heating)

It can be used when stationary, when the engine is switched off to preheat the

›

vehicle and while driving (e.g. during the heating phase of the engine); It works in tandem with the hearer, air-conditioning system or Climatronic;

›



89 90



Using the system

The engine is also preheated when the vehicle is stationary and the engine is

›

not running; It warms up the coolant by burning fuel from the vehicle tank. The coolant

›

warms up the air, which (if the blower speed is not set to zero) flows into the passenger compartment.

Auxiliary ventilation

The auxiliary ventilation enables fresh air to flow into the vehicle interior by switching off the engine, whereby the interior temperature is effectively decreased (e.g. with the vehicle parked in the sun).

WARNING

■

The auxiliary heating must never be operated in closed rooms - risk of poi-

soning!

■

The auxiliary heating must not be running during refuelling - risk of fire.

■

The exhaust pipe of the auxiliary heating is located on the underside of the vehicle. Therefore, if you wish to operate the auxiliary heating, do not park the vehicle in such a way that the exhaust gases can come into contact with highly flammable materials (e.g. dry grass) or easily inflammable substances (e.g. spilt fuel).

CAUTION

■

The running auxiliary heater consumes fuel from the vehicle tank and automati-

cally controls the filling level. If only a low quantity of fuel is present in the fuel tank, the function of the auxiliary heating is blocked.

■

The exhaust pipe of the auxiliary heating, which is located on the underside of

the vehicle, must not be clogged and the exhaust flow must not be blocked.

■

If the auxiliary heating and ventilation is running, the vehicle battery discharges.

If the auxiliary heating and ventilation has been operated several times over a longer period, the vehicle must be driven a few kilometres in order to recharge the vehicle battery.

Note

■

The auxiliary heating only switches the blower on, if it has achieved a coolant

temperature of approx. 50 °C.

■

At low outside temperatures, this can result in a formation of water vapour in

the area of the engine compartment. This is quite normal and is not an operating problem.

■

The air inlet in front of the windscreen must be free of e.g. ice, snow or leaves

to ensure that the auxiliary heating and cooling system operates properly.

Switching on/off

Fig. 87 Button for switching on/off the system directly on the operating part of the air conditioning/Climatronic

First read and observe the introductory information and safety warnings on page 88.



Switching on

Manually using the button on the operating part of the air conditioning/Climatronic. The warning light in



the button lights up.



Manually using the radio remote control. » page 90 Automatically through the configured and activated

departure time.

Switching off

Manually using the button on the operating part of the air conditioning/Climatronic. The warning light in



the button goes out.



Manually using the radio remote control. » page 90 Automatically when the pre-set departure time is

reached or when the pre-set run time has elapsed.

Automatically when the indicator light lights up . » page 10

Automatically when the charge state of the vehicle battery dropped too far.

After switching the system off, the auxiliary heating will continue running a little while longer in order to burn the remaining fuel in the auxiliary heater. Exhaust



fumes from the system will thus be directed outside.

» Fig. 87

» page 90

» Fig. 87

» page 90

» page 176



Heating and air conditioning system

After switching off the auxiliary heating, the coolant pump runs for a short period.

The auxiliary heater does not switch on:

when the following appears in the instrument cluster display, or the the follow-

›

ing was displayed before the ignition was turned off: Please refuel. Range: ... km or PLEASE REFUEL;

when the charge state of the vehicle battery is too low;

›

when no pre-set time is activated.

›

setting

First read and observe the introductory information and safety warnings



Information on the setting » Bedienungsanleitung Infotainment, chapter Setting vehicle systems (CAR button).

Before the setting is started, check the correct time and date settings.

Checking the settings

When the departure time is activated, the indicator light in the button for around 10 seconds after the ignition is turned off.

on page 88.



lights up

Remote control

Fig. 88

Auxiliary heater: Radio remote control

First read and observe the introductory information and safety warnings on page 88.



Explanation of graphic

Aerial

Battery cover

Warning light



Switch on the auxiliary heating





Switch off the auxiliary heating

The transmitter and the battery are housed in the housing of the remote control. The receiver is located in the interior of the vehicle.

When the battery is fully charged, the range of the remote control is a few hundred metres. Obstacles between the radio remote control and the vehicle, bad weather conditions and a weaker battery can clearly reduce the range.

To switch the auxiliary heating on or off, hold the remote control vertical, with the aerial pointing upwards. The antenna must not be covered with the fingers or the palm of the hand during this process.

The auxiliary heating can only be switched on/off safely using the radio remote control, if the distance between the radio remote control and the vehicle is at least 2 m.

After pressing the button, the warning light in the remote control gives the user different kinds of feedback:

Display warning light C » Fig. 88 Description

Lights up green for around 2 seconds. The auxiliary heating was switched on. Lights up red for around 2 seconds. The auxiliary heating was switched off. Slowly flashes green for around 2 sec-

onds.

Quickly flashes green for around 2 seconds.

Flashes red for around 2 seconds. The switch off signal was not received. Lights up orange for around 2 seconds,

then green or red.

Lights up orange for around 2 seconds, then flashes green or red.

Flashes orange for around 5 seconds.

The ignition signal was not received.

The auxiliary heating is blocked, e. g because the tank is nearly empty or there is a fault in the auxiliary heating.

The battery is weak, however the switching on or off signal was received.

The battery is weak, however the switching on or off signal was not received.

The battery is discharged, however the switching on or off signal was not received.



Using the system

CAUTION

The radio remote control comprises electronic components and must therefore be protected against water, severe impacts and direct sunlight.

Replacing the battery in the remote control

First read and observe the introductory information and safety warnings on page 88.



If the indicator light C » Fig. 88 on page 90on the radio remote control indicates a weak or discharged battery, it must be replaced.

The battery is located under a cover B » Fig. 88 on page 90 on the back of the radio remote control.

Insert a flat, blunt object, such as a coin, into the gap of the battery cover.

›

Turn the cover against the direction of the arrow up to the mark to open the

›

cover. Replace the battery.

›

Return the battery cover.

›

Turn the cover in the direction of the arrow up to the initial marking, engage.

›

When replacing the battery, pay attention to the correct polarity. The replacement battery must have the same specification as the original battery.

For the sake of the environment

Dispose of the used battery in accordance with national legal provisions.



Heating and air conditioning system

Starting-off and Driving

Starting and stopping the engine

Introduction



This chapter contains information on the following subjects: Adjusting the steering wheel position

Power steering 93 Electronic immobiliser 93 Ignition lock 94 Starting engine 94 Switching the engine off 94

Starting and stopping the engine on vehicles with the KESSY system » page 95.

WARNING

■

Never adjust the steering wheel when the vehicle is moving only when the

vehicle is stationary!

■

Maintain a distance of 25 cm 1 to the steering wheel » Fig. 89 on page 93 – . Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you – hazard!

■

The lever for adjusting the steering wheel must be locked whilst driving so that the position of the steering wheel cannot accidently change during the journey – risk of accident!

■

If the steering wheel is adjusted further towards the head, the protection provided by the driver airbag in the event of an accident is reduced. Check that the steering wheel is aligned to the chest.

■

When driving, hold the steering wheel with both hands firmly on the outer edge in the 9 o'clock and 3 o'clock position. Never hold the steering wheel in the 12 o'clock position or in any other way (e.g. in the middle or inner edge of the steering wheel). In such cases, you could injure the arms, hands and head when the driver airbag is deployed.

WARNING (Continued)

■

When driving, the ignition key must always be in the position 2 » Fig. 90 on page 94 (ignition switched on) without the engine running. This position is indicated by the warning lights coming on. If this is not the case, it could result in unexpected locking of the steering wheel – risk of accident!

■

Only pull the ignition key from the ignition lock when the vehicle has come to a complete stop (by applying the handbrake). Otherwise the steering wheel could block – risk of accident!

■

When leaving the vehicle, the ignition must always be removed. This is particularly important if children are left in the vehicle. Otherwise the children could, for example, start the engine – risk of accident or injury!

■

Never leave the engine running in unventilated or closed rooms. The exhaust gases of the engine contain besides the odorless and colourless carbon monoxide a poisonous gas – hazard! Carbon monoxide can cause unconsciousness and death.

■

Never leave the vehicle unattended with the engine running.

■

Never switch off the engine before the vehicle is stationary – risk of accident!

CAUTION

■

The starter may only be operated (ignition key position 3 » Fig. 90 on

page 94), if the engine is not running. The starter or engine can be damaged if the starter is activated when the engine is running.

■

Avoid high engine revolutions, full throttle and high engine loads as long as the

engine has not yet reached its operating temperature – risk of damaging the engine!

■

Do not tow start the engine - danger of damaging the engine! On vehicles with

a catalytic converter, unburnt fuel may get into the catalytic converter where it may ignite. This in turn may damage the catalytic converter. The battery from another vehicle can be used as a jump-start aid » page 195.

■

Do not switch the engine off immediately at the end of your journey after the

engine has been operated over a prolonged period at high loads but leave it to run at an idling speed for about 1 minute. This prevents any possible accumulation of heat when the engine is switched off.

For the sake of the environment

Do not warm up the engine while the vehicle is stationary. If possible, start your journey as soon as the engine has started. Through this the engine reaches its operating temperature more rapidly and the pollutant emissions are lower.



Using the system

Note

■

The engine can only be started with a genuine ŠKODA key with the matching

code.

■

The engine running noises may louder at first be louder for a short time after

starting the cold engine. This is quite normal and is not an operating problem.

■

After switching off the ignition, the radiator fan can intermittently continue to

operate for approx. 10 minutes.

■

If the engine also does not start after the second attempt, the fuse for the electric fuel pump (in petrol engines) or the control unit for the glow plug system or glow plug system relay and fuel pump (in diesel engines) could be faulty. Check the fuse and replace, if necessary » page 199 or seek assistance from a ŠKODA specialist garage.

■

We recommend locking the steering wheel whenever leaving the vehicle. This acts as a deterrent against the attempted theft of your car.

Adjusting the steering wheel position

Adjustable steering wheel: Lever below the steering wheel/safe dis-

Fig. 89

tance to the steering wheel

First read and observe the introductory information and safety warnings



The height and forward/back position of the steering wheel can be adjusted.

First of all adjust the driver's seat » page 59.

›

Pull the lever below the steering wheel down » Fig. 89 – .

›

Adjust the steering wheel to the desired position (with regard to the height and

›

forward/back position).

Push the lever upwards to the stop.

›

on page 92.

Power steering

First read and observe the introductory information and safety warnings on page 92.



The power steering enables you to steer the vehicle with less physical force. It is still possible to fully steer the vehicle if the power steering fails or if the en-

gine is not running (vehicle being towed in). However, greater physical effort is required to turn the steering wheel.

Steering force assistance can be influenced by the selection of driving mode » page 124.



Electronic immobiliser

First read and observe the introductory information and safety warnings



An electronic chip is integrated in the head of the key. The immobiliser is deactivated with the aid of this chip when the key is inserted in the ignition lock. The electronic immobiliser is automatically activated when the ignition key is withdrawn from the lock.

The engine will not start if a non-authorized ignition key is used. The following message is shown in the information cluster display:

Immobilizer active.

IMMOBILIZER ACTIVE



on page 92.



Starting-off and Driving

Ignition lock

Fig. 90

Positions of the vehicle key in the ignition lock

First read and observe the introductory information and safety warnings on page 92.



Petrol engines » Fig. 90

Ignition switched off, engine off, the steering can be locked

Ignition switched on

Starting engine

Diesel engines » Fig. 90

Fuel supply interrupted, ignition switched off, engine switched off, the steering can be locked

Heating glow plugs on, ignition switched on

Starting engine

To lock the steering, with the ignition key withdrawn, turn the steering wheel until the steering locking pin engages audibly.

If the steering is locked and the key cannot or can only be turned with difficulty into the position steering lock will unlock.

» Fig. 90, move the steering wheel back and forth and the

Starting engine

First read and observe the introductory information and safety warn-

on page 92.

ings



Vehicles with a diesel engine are equipped with a glow plug system. The glow plug warning light  comes on after the ignition has been switched on. Start the engine just after the indicator light  goes out.

You should not switch on any major electrical components during the heating period otherwise the vehicle battery will be drained unnecessarily.

Procedure for starting the engine

Before starting the engine, place the gearshift lever into neutral or place the se-

›

lector lever in the position P or N and firmly put on the handbrake. Switch on the ignition 2 » Fig. 90 on page 94.

›

Depress and hold the clutch pedal (vehicles with a manual gearbox) or brake

›

pedal (vehicles with an automatic gearbox) until the engine starts. Turn the key into position

›

touch the accelerator.

After letting go, the vehicle key will return to position

If the engine does not start within 10 seconds, turn the key to position 1. Re-

›

peat the start-up process after approx. half a minute. Release the handbrake before starting off.

›

The engine will not start if the engine is started without the clutch pedal (vehicles with a manual gearbox) or brake pedal (vehicles with an automatic gearbox) being depressed.

The following message is shown in the information cluster display: Press the clutch to start. or Apply the break to start. at the same time the indica-

tor light lights up . or

PRESS CLUTCH or APPLY BRAKE at the same time the indicator light lights up .

as far as it will go and release immediately- do not

Switching the engine off

First read and observe the introductory information and safety warnings on page 92.





Switch off the engine by turning the ignition key into position 1 » Fig. 90 on page 94.



Using the system

KESSY system

Unlocking and locking the steering

 Introduction

This chapter contains information on the following subjects: Unlocking and locking the steering

Switching on the ignition 96 Switching off the ignition 96 Emergency ignition shutoff system 96 Starting engine 96 Emergency start-up of the engine 97 Switching the engine off 97

The KESSY system makes it possible to switch the ignition on/off and to start/ stop the engine without actively using the key.

A key must be in the vehicle to unlock the steering, switch on the steering and start the vehicle.

WARNING

■

Never switch off the ignition while driving, as the power steering and brake

booster will no longer operate - risk of accident!

■

Never leave the keys in the vehicle, if leaving children unattended in the ve-

hicle. Otherwise the children could start the engine - risk of accident!

Note

■

After pressing the starter button while the steering is locked, the steering is unlocked, the electrical components are activated (e.g. Infotainment, etc.) and the ignition is switched on.

■

If you do not leave the vehicle after locking the steering and wish to unlock the steering again, press the starter button. At the same time, electrical components are activated (e.g. Infotainment etc.) and the ignition is switched on.

■

The KESSY system is protected against inadvertently switching off the engine while driving, this means that the engine can only be switched off in an emergency » page 96.

■

The steering is not unlocked or locked if the starter button is repeatedly pressed at short intervals.

Fig. 91

Starter button

First read and observe the introductory information and safety warnings on page 95.



Unlocking

Open the driver's door and get into the vehicle.

›

Close the driver's door, and the steering is unlocked within 2 seconds.

›

Locking

Stop the vehicle.

›

Switch off the engine or the ignition by pressing the starter button » Fig. 91.

›

Open the driver's door and the steering is locked.

›

If the driver's door is opened and the ignition is switched off afterwards, the steering is only locked after the vehicle is locked.

If the steering is locked and the KESSY system does not manage to unlock the steering lock the first time (e.g. if the wheels are resting against the curb), the attempt will be repeated twice by the system.

If the steering lock is then not unlocked, the following message is shown in the instrument cluster display:

Move steering wheel!

MOVE STEERING WHEEL

Slightly move the steering and the system will complete 3 more attempts to unlock after 2 seconds. At the same time, the indicator light  flashes.



It is necessary to eliminate the possible cause which is preventing the unlocking and then repeat the attempt to unlock the steering.



Starting-off and Driving

Switching on the ignition

First read and observe the introductory information and safety warnings on page 95.



The steering must be unlocked to switch on the ignition.

Briefly press the starter button » Fig. 91 on page 95 and the ignition is switched

›

on.

If the ignition is switched on and the driver's door is opened, the following message appears in the instrument cluster display:

Ignition on!

IGNITION STILL ON

Switching off the ignition

First read and observe the introductory information and safety warnings on page 95.



Briefly press the starter button » Fig. 91 on page 95 and the ignition is switched

›

off.

The ignition can be switched off up to a speed of 2 km/h. On vehicles fitted with a manual gearbox, the clutch pedal must not be depressed

after switching off the ignition otherwise the system would try to start. On vehicles fitted with an automatic gearbox, the selector lever must be in the

position P or N and the brake pedal must not be depressed.

Emergency ignition shutoff system

First read and observe the introductory information and safety warnings on page 95.



In an emergency, it is possible to switch off the ignition even at speeds greater than 2 km/h, by using the "emergency ignition shutoff system".

Press the starter button » Fig. 91 on page 95 for longer than 1 second or twice

›

within 1 second.

Starting engine

First read and observe the introductory information and safety warnings on page 95.



Maintain the clutch pedal depressed when starting vehicles fitted with a manual gearbox. On vehicles with an automatic gearbox, place the selector lever in position P or N and depress the brake pedal until the engine starts.

The engine will not start if the engine is started without the clutch pedal (vehicles with a manual gearbox) or brake pedal (vehicles with an automatic gearbox) being depressed.

The following message is shown in the information cluster display: Press the clutch to start. or Apply the break to start. at the same time the indica-



tor light lights up . or

PRESS CLUTCH or APPLY BRAKE at the same time the indicator light lights up .

Petrol engines

Briefly press the starter button » Fig. 91 on page 95 - the engine fires up.

›

Diesel engines

Briefly press the starter button - the engine starts after the indicator light

›

goes out.

The diesel engine can also be started by pressing the starter button, the ignition is switched on and the glow plug warning light  illuminates. Wait until the glow plug warning light goes out and then press and hold the starter button until the engine starts.







Using the system

Emergency start-up of the engine

Brakes

Fig. 92

Emergency start-up of engine

First read and observe the introductory information and safety warnings on page 95.



If the authorisation check for the key fails,the following message appears in the instrument cluster display:

Key not detected.

NO KEY

The emergency start-up must be completed.

Press the starter button » Fig. 92 and then hold the key to the starter button;

›

press the starter button directly with the key.

›

Note

During an emergency start-up of the engine, the key bit must face the starter button » Fig. 92.

Switching the engine off

First read and observe the introductory information and safety warnings on page 95.



Stop the vehicle.

›

Switch off the engine by pressing the starter button » Fig. 91 on page 95, doing

›

so switches off the ignition at the same time.

Information for braking

Wear-and-tear

The wear of the brake pads is dependent on the operating conditions and driving style.

The brake pads wear more quickly if a lot of journeys are completed in towns and over short distances or if a very sporty style of driving is adopted. If operated under severe conditions, the thickness of the brake pads must be checked by a ŠKODA specialist garage between service appointments as well.

Wet roads or road salt

The performance of the brakes can be delayed as the brake discs and brake pads may be moist or have a coating of ice or layer of salt on them in winter. The brakes are cleaned and dried by applying the brakes several times.

Corrosion

Corrosion on the brake discs and dirt on the bake pads occur if the vehicle has been parked for a long period and if you do not make much use of the braking system. The brakes are cleaned and dried by applying the brakes several times.

Faults in the brake surface

If it is found that the braking distance has suddenly become longer and that the brake pedal can be depressed further, the brake system may be faulty. Visit a ŠKODA specialist garage immediately and adjust your style of driving appropriately as you will not know how great the damage is.

Low brake fluid level

An insufficient level of brake fluid may result in problems in the brake system. The level of the brake fluid is monitored electronically » page 14, Brake system .

Brake booster



The brake booster increases the pressure generated with the brake pedal. The brake booster only operates when the engine is running.





Starting-off and Driving

WARNING

■

Greater physical effort for braking is required when the engine is switched

off – risk of accident!

■

During the braking procedure on a vehicle with manual transmission, when

the vehicle is in gear and at low revs, press the clutch pedal. If you fail to do so, the functionality of the brake booster can be impaired – risk of accident!

■

If a front spoiler, full wheel trim, etc. is mounted retrospectively, it must be

ensured that the air supply to the front wheel brakes is not reduced. The front brakes may overheat which can have a negative impact on the functioning of the braking system - risk of accident!

Handbrake

Fig. 93

Centre console: Handbrake

CAUTION

■

Observe the recommendations on the new brake pads » page 100.

■

Never let the brakes slip with light pressure on the pedal if braking is not necessary. This causes the brakes to overheat and can also result in a longer braking distance and excessive wear.

Note

■

If the brakes are applied in full and the control unit for the braking system considers the situation to be dangerous for the following traffic, the brake light flashes automatically. After the speed was reduced below around 10 km/h or the vehicle was stopped, the brake light stops flashing and the hazard warning light system switches on. The hazard warning light system is switched off automatically after accelerating or driving off again.

■

Before negotiating a steep downhill section, reduce the speed, shift down into the next lower gear (manual gearbox) or select a lower drive position (automatic gearbox). As a result, the braking effect of the engine will be used, reducing the load on the brakes. Any additional braking should be completed intermittently, not continuously.

Using the system

Apply

Pull the handbrake lever firmly upwards.

›

Loosening

Pull the handbrake lever up slightly and at the same time push in the locking

›

button » Fig. 93. Move the lever right down while pressing the lock button.

›

The handbrake warning light  lights up when the handbrake is applied, provided the ignition is on.

A warning signal sounds if the vehicle is inadvertently driven off with the handbrake applied.

The following message is shown in the information cluster display:

Release the parking brake!

PARKING BRAKE ON PLEASE RELEASE



The handbrake warning is activated if the vehicle is driven at a speed of more than around 5 km/h for more than 3 seconds.

WARNING

■

Please note that the handbrake must be fully released. A handbrake which is only partially released can result in the rear brakes overheating. This can have a negative effect on the operation of the brake system - risk of accident!

■

Never leave children unattended in the vehicle. The children might, for example, release the handbrake or take the vehicle out of gear. The vehicle might then move off – risk of accident!



Skoda Octavia 2012 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual