You have opted for a Škoda - our sincere thanks for your confidence in us.
Your new Škoda offers you a vehicle featuring the most modern engineering and a wide range of equipment which
you will undoubtedly wish to use to the full during your daily motoring. That is why, we recommend that you read
this Owner's Manual attentively to enable you to become familiar with your car and all that it offers as quickly as
possible.
Please do not hesitate to contact your specialist garage or importer should you have any further questions or any
problems regarding your vehicle which may arise. He will be ready at any time to receive your questions, suggestions and criticisms.
National legal provisions, which deviate from the information contained in these operating instructions, take precedence over the information contained in the operating instructions.
We wish you much pleasure with your Škoda and pleasant motoring at all times.
Yo ur Škoda Auto
Introduction2
On-board literature
The on-board literature for your vehicle consists of this “Owner's Manual”
as well as a “Service schedule” and a “Help on the road”. There can also be
a variety of other additional operating manuals and instructions on-board
(e.g. an operating manual for the radio) depending on the vehicle model and
equipment.
If one of the publications listed above is missing, please contact an authorised Škoda dealer immediately, where one will be glad to assist you in such
matters.
One should note that the details given in the vehicle's papers always
take precedence over those in the Owner's Manual.
Owner's Manual
This Owner's Manual describes the current scope of equipment. Certain
items of equipment listed are only installed later on and only envisaged for
particular markets. The illustrations can differ in minor details from your
vehicle; they are only intended for general information.
In addition to information regarding all the controls and equipment, the
Owner's Manual also contains important information regarding care and
operation for your safety and also to retain the value of your vehicle. To
provide you with valuable tips and aids. You will learn how you can operate
your vehicle safely, economically and in an environmentally conscious
way.
For safety reasons, please also pay attention to the information on
accessories, modifications and replacement of parts page 214.
The Service schedule
contains:
Vehicle data,
Service intervals,
Overview of the service work,
Service proof,
Confirmation of mobility warranty (only valid in certain countries),
important information on the warranty.
The confirmations of the carried out service work are one of the conditions
for possible warranty claims.
Please always present the Service schedule when you take your car to an
authorised Škoda Service Partner.
If the Service schedule is missing or worn, please contact your authorised
Škoda Service Partner, where your car is serviced regularly. You will receive a
duplicate, in which the previously carried out service work are confirmed.
Help on the road
contains the most important telephone numbers in individual countries as
well as the addresses and telephone numbers of Škoda importers.
The other chapters of the Owner's Manual are also important, however, for
proper treatment of your car - in addition to regular care and maintenance helps to retain its value and in many cases is also one of the conditions for
possible warranty claims.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Layout of this Owner's Manual (explanations)6
WARNING
Caution
For the sake of the environment
Note
Layout of this Owner's Manual (explanations)
The Owner's Manual has been systematically designed, in order to make it easy for you
to find and absorb the information you require.
Chapters, table of contents and subject index
The text of the Owner's manual is divided into relatively short sections which are
combined into easy-to-read chapters. The chapter you are reading at any particular
moment is highlighted at the bottom right of the page.
The Table of contents is arranged according to the chapters and the detailed Subject index at the end of the Owner's Manual helps you to rapidly find the information you
are looking for.
Sections
The majority of Sections apply to all models.
Since there is a wide range of different equipment and options available it is clearly
unavoidable, despite dividing the contents into sections, that mention may be made
of equipment which is not fitted to your vehicle.
Brief information and instructions
Each section has a Heading.
This is followed by Brief information (in large italic lettering), which tells you the
subject which is dealt with in this section.
Most of the illustrations are accompanied by an Instruction (in relatively large letters)
which explains to you in a straightforward way the action you have to take. Work steps
which have to be carried out are illustrated with a hyphen.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of
travel of the vehicle.
Explanation of symbols
Equipment which is marked in such a way is only standard on certain vehicle model
versions or only suppliable as optional equipment for certain models.
End of a section.
The section is continued on the next page.
Notes
All four kinds of notes, which are used in the text, are always stated at the end of the
respective section.
The most important notes are marked with the heading WARNING. These
WARNING notes draw your attention to a serious risk of accident or injury.
While reading the text you will frequently encounter a double arrow followed
by a small warning symbol. This symbol is intended to draw your attention to a
WARNING note at the end of the section to which you must pay careful attention.
A Caution note draws your attention to the possibility of damage to your vehicle (e.g.
damage to gearbox), or points out general risks of an accident.
An Environmental note draws your attention to environmental protection aspects.
This is where you will, for example, find tips aimed at reducing your fuel consumption.
A normal Note draws your attention in a general way to important information.
Using the system
7
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Cockpit8
Fig. 1 Certain items of equipment shown in the illustration are only fitted to particular model versions or are optional items of equipment.
Cockpit
Note
A
1
46
A
2
65
A
3
94
A
4
57
113
A
5
151
122
A
6
15
A
7
19
61
A
8
73
A
9
94
A
10
56
A
11
87
A
12A13
73
A
14
86
A
15
157
A
16
151
A
17
226
A
18
51
A
19
55, 56
A
20
196
A
21
87
A
22
10
A
23
107
A
24
9597100
A
25
169
A
26
112
A
27
110
118
A
28
172
A
29
83
88
A
30
157
Cockpit9
Overview
This overview will help you to quickly familiarise yourself with the
displays and the control elements.
Indicator light for a switched off front seat passenger airbag* . . . . . .
Cars with factory-fitted radio or navigation system are supplied with separate
instructions for operating such equipment.
The arrangement of the control elements on right-hand drive models may differ to
some extent from that shown in page 8, fig. 1. However the symbols correspond to
the individual control elements.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
The brief instruction10
WARNING
Fig. 2 Remote control key
A1A2A3A
4
The brief instruction
Basic functions and important information
Introduction
The chapter of the brief instruction is only used as a quick reference of
the most important operating elements of the vehicle. It is necessary to
observe all the information which is contained in the following chapters
of the Owner's Manual.
Unlocking and locking the vehicle
Unlocking the vehicle
Unlocking the boot lid
Locking the vehicle
Folding out/folding up of the key
Further information page 43, “Unlocking and locking the vehicle”.
Setting steering wheel position
Fig. 3 Adjustable steering wheel: Lever on the steering column / the correct distance of the
driver from the steering wheel
You can set the height and the forward/back position of the steering wheel to the
desired position.
– Pull the lever below the steering wheel down fig. 3 - left.
– Set the steering wheel to the desired position (concerning height and forward/back
position).
– Push the lever upwards as far as the stop.
Further information page 107, “Setting steering wheel position”.
Adjust the steering wheel so that the distance between the steering wheel
and your chest is at least 25 cm fig. 3 - right. Not maintaining this minimum
distance will mean that the airbag system will not be able to properly protect
you - hazard!
You must not adjust the steering wheel when the vehicle is moving!
For safety reasons the lever must always be firmly pushed up to avoid the
steering wheel altering its position unintentionally when driving - risk of
accident!
The brief instruction11
WARNING
WARNING
Fig. 4 Front seat: Seat belt height
adjuster
Fig. 5 Controls at sea t
A1A2A3A
4
Fig. 6 Inner part of door: Rotary knob
Seat belt height adjuster
– Move the height adjuster in the desired direction up or down fig. 4.
– Then pull firmly on the belt to ensure that the seat belt height adjuster has correctly
locked in place.
Further information page 147, “Seat belt height adjuster”.
Adjust the height of the belt in such a way that the shoulder part of the belt is
positioned approximately across the middle of your shoulder - on no account
across your neck!
Adjusting the front seats
Adjusting a seat in a forward/back direction
Adjusting height of seat*
Adjust the angle of the seat backrest
Adjusting lumbar support*
Further information page 67, “Adjusting the front seats”.
Only adjust the driver seat when the vehicle is stationary - risk of injury!
Electric exterior mirror adjustment*
Heating of the external mirror
Adjusting left and right exterior mirrors simultaneously
Adjusting the right-hand exterior mirror
Switching off operating control
Folding in both exterior mirrors*
Further information page 65, “Exterior mirror”.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
The brief instruction12
Fig. 7 Dash panel: Light switch
Fig. 8 Turn signal and main beam lever
AAABACA
D
Fig. 9 Windscreen wiper lever
AAA0A
1
Switching lights on and off
Further information page 51, “Switching lights on and off ”.
Automatic light control*
Switching off all lights/daylight driving lights*
Switching on side lights
Switching on the low beam and main beam
Fog lights*
Rear fog light
Turn signal and main beam lever
Turn signal light right
Turn signal light left
Switching over between low beam and main beam lights
Headlight flasher
Further information page 57, “The turn signal and main beam lever ”.
with counter for distance driven page 17
with Service Interval Display page 17
with digital clock page 18
with Multi-functional indicator* page 19
with Information display* page 22
Button for the selection of the mode (turn button) / the setting (press button):
Set hours / minutes
Activating / deactivating the second speed in mph or km/h*
Service interval - Display of the remaining number of days, kilometres or miles
to the next Inspection Service / Reset*
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
The red zone of the rev counter scale fig. 15 indicates the range in which the
engine control unit begins to limit the engine speed. The engine control unit restricts
the engine speed to a steady limit value.
Shift into the next higher gear or select the selector lever position D of the automatic
gearbox before reaching the red zone of the rev counter scale.
1)
Valid for countries where the values are indicated in British measuring units.
Instruments and warning lights16
For the sake of the environment
Note
WARNING
Caution
Caution
A
3
A
6
Avoid high engine speeds during the driving time and before the engine has been
warmed up to operating temperature page 175.
Shifting up early helps you save fuel and reduce the operating noise of your vehicle.
Speedometer
Warning against excessive speeds*
An acoustic warning signal will sound when the vehicle speed exceeds 120 kilometres
per hour. The acoustic warning signal will switch off again when the vehicle speed goes
below this speed limit.
This function is only valid for some countries.
Coolant temperature gauge
The coolant temperature gauge page 15, fig. 15 operates only when the ignition
is switched on.
In order to avoid any damage to the engine, please pay attention to the following notes
regarding the temperature ranges.
Cold range
If the pointer is in the left-hand area of the scale it means that the engine has not yet
reached its operating temperature. Avoid running at high engine speeds, at full throttle
and at severe engine loads.
The operating range
The engine has reached its operating temperature as soon as the pointer moves into
the mid-range of the scale. The pointer may also move further to the right at high
engine loads and high outside temperatures. This is not critical provided the warning
symbol in the instrument cluster does not flash.
If the symbol in the instrument cluster flashes it means that either the coolant
temperature is too high or the coolant level is too low. Observe the guidelines
page 31, “Coolant temperature/coolant level ”.
Pay attention to the warning notes page 197, “Working in the engine
compartment” before opening the bonnet and inspecting the coolant level.
Additional headlights and other attached components in front of the fresh air inlet
impair the cooling efficiency of the coolant. There is then a risk of the engine overheating at high outside temperatures and high engine loads!
Fuel gauge
The fuel gauge page 15, fig. 15 only operates when the ignition is switched on.
The fuel tank has a capacity of about 55°litres or 60 litres 2). The warning symbol in
the instrument cluster lights up when the pointer reaches the reserve marking. There
are now about 9 litres of fuel remaining in the tank. This symbol is a reminder for you,
that you must refuel.
The following will be displayed in the information display*:
Please refuel!
An audible signal sounds as an additional warning signal.
Never run the fuel tank completely empty! The irregular supply of the fuel system can
lead to irregular running of the engine. Unburnt fuel may get into the exhaust system
and damage the catalytic converter.
2)
Valid for Octavia Combi 4x4 and Octavia Scout.
Note
After filling up, it can occur that during dynamic driving (e.g. numerous curves, braking,
WARNING
Note
A
5
Fig. 16 Service Interval Display: Note
driving downhill and climbing a steep hill) the fuel gauge indicates approx. a fraction
less. When stopping or during less dynamic driving, the correct fuel supply quantity is
indicated. This effect is not a fault.
Counter for distance driven
The distance which you have driven with your vehicle is shown in kilometres (km). In
some countries the measuring unit “mile” is used.
Reset button
If you hold the reset button page 15, fig. 15 pressed for about 1 second, the trip
counter is set back to zero.
Trip counter for distance driven
The trip counter indicates the distance which you have driven since it was last reset in steps of 100 metres or 1/10 of a mile.
Counter for distance driven
The counter for distance driven indicates the total distance in kilometers or miles
which the vehicle has been driven.
Fau lt dis play
If there is a fault in the instrument cluster, the constant text Error appears in the display.
Have the fault rectified as soon as possible by a specialist workshop.
Never seek to adjust the trip counter for distance driven while driving for safety
reasons !
If vehicles which are fitted with the information display* the display of the second
speed is activated in mph or km/h, this driving speed is indicated instead of the
counter for the total distance driven.
Instruments and warning lights17
Service Interval Display
Depending on the equipment installed in the vehicle, the text can differ on the display.
Service Interval Display
Before the next service interval a key symbol and the remaining kilometers are
indicated after switching on the ignition fig. 16. At the same time, a display appears
regarding the remaining days until the next service interval.
The following will be displayed in the information display*:
Service in ... km or ... days
The kilometre indicator or the days indicator reduces in steps of 100 km. or days until
the service due date is reached.
A flashing key symbol and the text Service appears in the display for 20 seconds
as soon as the due date for the service is reached.
The following will be displayed in the information display*:
Service now!
Resetting Service Interval Display
It is only possible to reset the Service Interval Display, if a service message or at least a
pre-warning is shown on the display of the instrument cluster.
We recommend having this resetting performed by a specialist garage.
The specialist garage:
resets the memory of the display after the appropriate inspection,
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and warning lights18
Caution
Note
WARNING
A5A5A
5
Fig. 17 Shift recommendation for
changing gears
A
AABAA
makes an entry in the Service schedule,
affix the sticker with the entry of the following service interval to the side of the
dash panel on the driver's side.
Reset the service interval displays by using the button page 15, fig. 15.
On vehicles which are equipped with information display*, you can call up this information in the following menu on page 23:
SETUP
Service Interval
Reset
We recommend that you do not reset the Service Interval Display yourself otherwise
this can result in the service interval display being incorrectly set, which may also result
in problems with operation of your vehicle.
Never reset the display between service intervals otherwise this may result in
incorrect readouts.
information is retained in the Service Interval Display also after the battery of the
vehicle is disconnected.
If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by a
specialist garage.
The data displayed is the same after resetting the display with flexible service inter-
vals (QG1) using the reset button as that for a vehicle with fixed service intervals (QG2).
We therefore recommend having the Service Interval Display reset only by an authorised Škoda Service Partner who is familiar with the procedure for resetting the display
with a vehicle system tester.
Please refer to the brochure Service schedule for extensive information about the
service intervals.
Digital clock
You can set the time with the rotary knob page 15, fig. 15.
Select the information which you wish to change by turning the button and carry
out the change of the selected information by pressing the button.
On vehicles which are fitted out with the information display*, it is possible to set the
time in the menu Time page 25.
The clock should not be adjusted while driving for safety reasons but only when
the vehicle is stationary!
Shift recommendation for changing gears*
An information for the engaged gear fig. 17 is shown in the display of the instrument cluster.
In order to minimise the fuel consumption, a recommendation for shifting into
another gear is indicated in the display.
If the control unit recognises that it is appropriate to change the gear, an arrow is
shown in the display. The arrow points up or down, depending on whether it is recommended to shift into a higher or lower gear.
At the same time, the recommended gear is indicated instead of the currently engaged
gear .
Instruments and warning lights19
Note
Fig. 18 Multi-functional indicator
A
B
A
D
Multi-functional indicator (onboard computer)*
Introduction
The multi-functional indicator appears in the display fig. 18 or in the information
display page 22 depending on the equipment fitted to your vehicle.
The multi-functional indicator offers you a range of useful information.
The outside temperature page 20
Driving time page 21
Current fuel consumption page 21
Average fuel consumption page 21
Range page 21
Distance driven page 21
Average speed page 22
Current speed* page 22
oil temperature* page 22
Warning against excessive speeds* page 22
On vehicles which are fitted out with information display*, it is possible to switch off
the display of some information.
In certain national versions the displays appear in the Imperial system of measures.
If the display of the second speed is activated in mph, the current speed* is not
indicated in km/h on the display.
Memory
The multi-functional indicator is equipped with two automatic memories. The
selected memory is displayed in the middle of the display field fig. 18.
The data of the single-trip memory (memory 1) is shown if a 1 appears in the display.
A 2 shown in the display means that data relates to the total distance memory
(memory 2).
Switching over the memory with the help of the button page 20, fig. 19 on the
windscreen wiper lever or with the help of the button on the multifunction steering
wheel* page 20, fig. 19.
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment the ignition
is switched on until it is switched off. New data will also flow into the calculation of the
current driving information if the trip is continued within 2 hours after switching off
the ignition. The memory will be is automatically erased, on the other hand, if the trip
is interrupted for more than 2 hours.
Total-trip memory (memory 2)
The total distance driven memory gathers data from any number of individual journeys up to a total of 19 hours and 59 minutes driving or 1.999 kilometres driven and
on vehicles which are fitted with information display* up to a total of 99 hours and 59
minutes driving or 9.999 kilometres driven. The memory is deleted when either of
these limits is reached and the calculation starts from anew.
The total-trip memory will not, contrary to the single-trip memory, be deleted after a
period of interruption of driving of 2 hours.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and warning lights20
Note
AAA
BADABADAAAC
A
D
A
DABADABADAAAC
All information in the memory 1 and 2 is erased if the battery of the vehicle is
disconnected.
Operating with the buttons on the windshield wiper lever and on
the multifunction steering wheel*
Fig. 19 Multi-functional indicator: Controls on the windshield wiper lever / controls on the
multifunction steering wheel
The rocker switch and the button are located on the windshield wiper lever
fig. 19. Switching over and resetting is performed with the handwheel fig. 19
on the multifunction steering wheel.
Selecting the memory
– After briefly pressing the button on the windshield wiper lever or by briefly
pressing the button on the multifunction steering wheel, you can select the
desired memory.
Selecting the functions with the help of the windshield wiper lever
– Press the top or bottom rocker switch for longer than 0.5 seconds. In this way,
call up in sequence the individual functions of the multi-functional indicator.
Selecting the functions with the help of the multifunction steering
wheel
– By pressing the button , you can call up the menu of the multi-functional indi-
cator.
– Turn the handwheel upwards or downwards. In this way, call up in sequence
the individual functions of the multi-functional indicator.
– Short-term pressing of the button allows to select the highlighted function.
Setting function to zero
– Select the memory you want.
– Press the button or for more than 1 second.
The following readouts of the selected memory will be set to zero with the button
on the windshield wiper lever or with the button on the multifunction steering
wheel:
average fuel consumption,
distance driven,
average speed,
Driving time.
You can only operate the multi-functional indicator when the ignition is switched on.
After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
Outside temperature
The outside temperature appears in the display when the ignition is switched on.
If the outside temperature drops below +4 °C, a snow flake symbol (warning signal for
ice on the road) appears before the temperature indicator and a warning signal
sounds. After pressing the rocker switch at the windshield wiper lever fig. 19 or
the button at the multifunction steering wheel fig. 19, the function shown last is
indicated.
WARNING
Do not only rely upon the information given on the outside temperature display
Note
A
BADABADABAD
that there is no ice on the road. Please note that black ice may also be present
on the road surface even at temperatures around +4°C - warning, drive with
care!
Driving time
The driving time which has elapsed since the memory was last erased, appears in the
display. If you wish to measure the driving time as of a particular time, you must set the
memory to zero at this moment in time by pressing the button on the windshield
wiper lever page 20, fig. 19 or the handwheel on the multifunction steering
wheel* page 20, fig. 19 for longer than 1 second.
The maximum time indicated in both memories is 19 hours and 59 minutes and on
vehicles which are fitted with information display*, it is 99 hours and 59 minutes. The
indicator is set back to null if this period is exceeded.
Current consumption
The current fuel consumption level is shown in the display in litres/100 km. This informat ion c an hel p you t o ada pt you r sty le of driving to the fuel consumption you wish to
achieve.
The display appears in litres/hour if the vehicle is stationary or driving at a low speed.
The indicated value will be updated every 0.5 seconds while you are driving.
Average fuel consumption
The average fuel consumption since the memory was last erased is shown in the
display in litres/100 km page 19. This information can help you to adapt your style
of driving to the fuel consumption you wish to achieve.
If you wish to determine the average fuel consumption over a certain period of time
you must set the memory to zero at the start of the measurement using the button
on the windshield wiper lever page 20, fig. 19 or with the handwheel on the
Instruments and warning lights21
multifunction steering wheel* page 20, fig. 19. A zero appears in the display for the
first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
The amount of fuel consumed will not be indicated.
Range
The estimated range in kilometres is shown on the display. It indicates the distance you
can still drive with your vehicle based on the present level of fuel in the tank for the
same style of driving.
The readout is shown in steps of 10 km. After lighting up of the indicator light for the
fuel reserve the display is shown in steps of 5 km.
The fuel consumption for the last 50 km is taken as a basis for calculating the range. If
you drive in a more economical manner from this moment on, the range will be
increased accordingly.
If the memory is set to zero (after disconnecting the battery), the fuel consumption of
10 ltr./100 km is calculated for the range; afterwards the value is adapted accordingly
to the style of driving.
Distance driven
The distance driven since the memory was last erased appears in the display
page 19. If you wish to measure the distance driven of a particular time, you must
set the memory to zero at this moment in time by pressing the button on the windshield wiper lever page 20, fig. 19 or the handwheel on the multifunction
steering wheel* page 20, fig. 19.
The maximum distance indicated in both memories is 1 999 km or on vehicles with
information display*, it is 9 999 km. The indicator is set back to null if this period is
exceeded.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and warning lights22
A
BAD
A2ABA
D
A
AADAB
ADABA
D
Average speed
The average speed since the memory was last erased is shown in the display in
km/hour page 19. If you wish to determine the average vehicle speed over a certain
period of time you must set the memory to zero at the start of the measurement using
the button on the windshield wiper lever page 20, fig. 19 or with the handwheel
on the multifunction steering wheel* page 20, fig. 19.
A zero appears in the display for the first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Current speed*
The current speed which is identical to the display of the speedometer, is indicated on
the display page 15, fig. 15.
oil temperature*
If the oil temperature is lower than 50°C or if a fault in the system for checking the oil
temperature is present, three lines are displayed instead of the oil temperature.
Warning against excessive speeds*
Warning against excessive speeds
This function enables you to set a speed limit, e.g. if you drive in town. A text in the
display is intended to draw your attention to the fact that you have exceeded the set
speed limit.
Select the menu point Speed warning --- km/h..
Drive e.°g at a speed of 50 km/h.
Press the button on the windshield wiper lever page 20, fig. 19 or the hand-
wheel on the multifunction steering wheel* page 20, fig. 19. Speed warning
50 km/h is displayed in the information display*.
The desired speed can also be set in steps of 5°km/h by pressing the button on the
windshield wiper lever page 20, fig. 19 or by turning the handwheel on the
multifunction steering wheel* page 20, fig. 19. The set speed is confirmed by
pressing the button on the windshield wiper lever page 20, fig. 19 or the handwheel on the multifunction steering wheel* page 20, fig. 19.
If you now exceed the set speed limit, Speed 50 km/h exceeded will be shown on the
display. This message is indicated for as long as the speed is reduced below the set
limit or switch off the message by pressing the button on the windshield wiper lever
page 20, fig. 19 or the handwheel on the multifunction steering wheel*
page 20, fig. 19.
An audible signal sounds as an additional warning signal.
The set speed limit remains stored even after switching off the ignition.
Information display*
Introduction
The information display provides you with information in a convenient way
concerning the current operating state of your vehicle. The information system also
provides you with data (depending on the equipment installed in the vehicle) relating
to the radio, mobile phone, multi-functional indicator, navigation system, the unit
connected to the MDI input and the automatic gearbox.
Certain functions and operating conditions are always being checked on the vehicle
when the ignition is switched on and also while driving.
Functional faults, if required repair work and other information are indicated by red
symbols page 24 and yellow symbols page 24.
Lighting up of certain symbols is combined with an acoustic warning signal.
Information and texts giving warnings are also shown in the display page 27.
The display of text is possible in the following languages:
Czech, English, German, French, Italian, Spanish, Portuguese, Russian and Chinese.
You can select the desired language in the setting menu.
The following information can be shown in the display (depending on the equipment
installed on the vehicle):
Instruments and warning lights23
Note
A
AAAABACADADACAC
ABA
D
Main menu page 23
Door, luggage compartment door and bonnet ajar warning
page 24
Service Interval Display page 17
Selector lever position for an automatic gearbox page 116
Main menu
Fig. 20 Information display: Controls on the windshield wiper lever / controls on the multifunction steering wheel
Operating with the buttons on the windshield wiper lever
– You can activate the MAIN MENU by pressing the rocker switch fig. 20 for
more than 1 second.
– You can select individual menu points by means of the rocker switch . When the
pushbutton is briefly pressed, the information you have selected is displayed.
Operating with the buttons on the multifunction steering wheel
– You can activate the MAIN MENU by pressing the rocker switch fig. 20 for
more than 1 second.
– You can select the individual menus by pressing the handwheel . After briefly
pressing the handwheel , the desired menu is indicated.
– After briefly pressing the button you can achieve a higher level, by pressing the
button for longer than 1 second, you can call up the MAIN MENU.
You can select the following information (depending on the equipment installed on
the vehicle):
MFD (Onboard computer) page 19
Audio*
Navigation*
Phone* page 125
Aux. Heating (auxiliary heating)* page 104
Assistants* page 53
Ve hicle s tatus page 24
Setup page 25
The menu point Audio is only then displayed when the factory-fitted Radio* is
switched on.
The menu point Navigation is only then displayed when the factory-fitted Navigation
system* is switched on.
The menu point Aux. Heating is only then displayed, if the vehicle is factory-fitted with
the auxiliary heating*.
The menu point Assistants is only then displayed, if the vehicle is fitted with cornering
lights*.
If warning messages are shown in the information display, these messages can be
confirmed with the button on the windshield wiper lever or with the button on
the multifunction steering wheel in order to call up the main menu.
If you do not activate the information display at that moment, the menu shifts to
one level higher every 10 seconds.
The operation of the factory-fitted radio* or the navigation system* is described in
separate operating instructions to be found in the on-board literature.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and warning lights24
Door, luggage compartment door and bonnet ajar warning
The door, luggage compartment and bonnet ajar warning lights up if at least one do or,
the luggage compartment or bonnet are not closed. The symbol indicates which door
is still open or whether the luggage compartment door or bonnet is not closed.
The symbol goes out as soon as the doors, luggage compar tment door and bonnet are
completely closed.
A warning signal sounds if the car is driven at a speed of more than 6km/hour and if
the engine or the luggage compartment door is open.
Auto Check Control*
Car state
The Auto Check Control carries out a check of certain functions and vehicle components. The check is performed constantly when the ignition is switched on, both when
the vehicle is stationary, as well as when driving.
Some operational faults, urgent repairs, service work or other information appear in
the display of the instrument cluster. The displays are shown with a red or yellow light
symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indicate a
warning (priortity 2). Information for the driver may also appear in addition to the
symbols page 27.
Shown in the menu Vehic le s tatu s, if there is at least one error message. After selecting
this menu the first of the error messages is displayed. Several error messages are
shown on the display under the message e.g. 1/3. This indicates that the first of a total
of three error messages is displayed. Investigate the displayed faults as soon as
possible.
As long as the operational faults are not rectified, the symbols are always indicated
again. After the first display, the symbols are indicated without information for the
driver.
If a fault occurs, a warning signal will also sound in addition to the symbol and text in
the display:
Priority 1 - three warning signals
Priority 2 - one warning signal
Red symbols
A red symbol signals danger.
– Stop the vehicle.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
Engine oil pressure too low page 30
Overheated clutches of the automatic gearbox
DSG*
Three successive warning signals will sound if a red symbol appears.
Yellow symbols
Check the relevant function as soon as possible.
The meaning of the yellow symbols:
page 36
Instruments and warning lights25
Check engine oil level,
engine oil sensor faulty
Brake pad worn page 34
It is also important to have the vehi-
cle inspected without delay by a spe-
Problem with engine oil pressure
In certain countries, if a yellow symbol appears one warning signal will sound as well.
If several operational faults of priority 2 exist, the symbols appear one after the other
and are each illuminated for about 5 seconds.
cialist garage. The information about
the maximum permissible engine
speed is displayed together with this
page 35
symbol.
Setup
You can change certain settings by means of the information display. The current
setting is shown on the information display in the respective menu at the top below the
line.
You can select the following information (depending on the equipment installed on
the vehicle):
Language
MFD Data
Convenience
Lights & Vision
Time
Winter tyres
Units
Assistants
Alt. speed dis.
Service Interval
Factory Setting
Back
After selecting the menu point Back you will reach one level higher in the menu.
Language
Here you can set in which language the warning and information texts should be
displayed.
Displays of the MFA
Here you can switch off or on certain displays of the multi-functional indicator.
Comfort*
You can set the following functions (depending on the equipment installed on the
vehicle):
On vehicles with rain sensor you can switch on or off the
Rain closing
Door openHere you can switch on or off the functions for opening a
ATA confirm
Window op.Here you can set the convenience mode only for the driver
function for automatic closing of the windows and the
sliding/tilting roof in case of rain and locked vehicle. If it is
not raining and the function is set, the windows including
the sliding/tilting roof are closed automatically after
approx. 12 hours.
single door and automatic closing.
Here you can set if a signal tone should sound additionally
when activating or deactivating the anti-theft alarm system
.
window or for all the windows.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Instruments and warning lights26
Mirror down
Here you can switch on or off the function for mirror lowering on the front passenger side when engaging the
reverse gear a).
Mirror adjust.Here you can switch on or off the function for left and right
exterior mirror adjustment simultaneously.
After selecting this menu the convenience setting is reset
Facto ry se ttin g
a)
This function is only available on vehicles with an electrically adjustable driver seat.
to factory setting. The following is displayed in the information display:
Convenience factory settings restored
Lights and Visibility
Here you can set how long the light should stay on for the function Coming/Leaving
Home. Furthermore you can here switch on or off the functions daylight driving lights
and convenience turn signal.
After selecting the menu point Fact ory s etti ng the factory setting of the lighting is
established again.
Time
Here you can set the time, the time format (12 or 24 hour indicator) and the time
change summer/winter time.
Winter tyres
Here you can set at which speed a warning signal should sound. This function is used
for e.g winter tyres with the permissible maximum speed less than the maximum
speed of the vehicle.
When exceeding the speed, the following is displayed on the information display*:
Winter tyres max. speed ... km/h
Measures
Here you can set the units for temperature, consumption and distance driven.
Assistant
Here you can adjust the tones of the acoustic signals of the parking aid*.
Second speed
Here you can switch on the display of the second speed in mph or in km/h3).
Service
Here you can have the kilometers still to be driven and the days until the following
service interval shown and the Service Interval Display reset.
Factory Setting
After selecting the menu point Factory Setting the factory setting of the information
display is established again.
3)
Valid for countries where the values are indicated in British measuring units.
Warning lights
Fig. 21 Instrument cluster with warning lights
Overview
The warning lights indicate certain functions or faults.
Turn signal lights (to the left) page 28
Instruments and warning lights27
Failure of the light bulbs page 29
Turn signal lights (to the right) page 28
Fog lights* page 29
Main beam light page 29
Low beam light page 29
Rear fog light page 29
Cruise control system* page 29
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Diesel particle filter* (diesel engine) page 29
Airbag system page 30
Control system for exhaust page 30
Electromechanical power steering page 30
Engine oil pressure page 30
EPC fault light (petrol engine) page 31
Instruments and warning lights28
WARNING
Note
Glow plug system (diesel engine) page 31
Coolant temperature/coolant level page 31
Traction control system (TCS) page 32
Electronic stability programme (ESP)* page 32
Switch off traction control system (TCS) page 32
Selector lever lock* page 33
Tyre pressure* page 33
Antilock brake system (ABS) page 33
Bonnet page 33
Seat belt warning light page 34
Brake pad wear* page 34
Boot lid page 34
Open door page 34
Fluid level in windshield washer system* page 34
Brake system page 34
Dynamo page 35
Engine oil level page 35
Fuel reserve page 35
If you do not pay attention to the warning lights coming on and the corre-
sponding descriptions and warning notes, this may result in severe body injuries or major vehicle damage.
The engine compartment of your car is a hazardous area. There is a risk of
injuries, scalding, accidents and fire when working in the engine compartment,
e.g. inspecting and replenishing oil and other fluids. It is also essential to
observe all warnings page 197, “Working in the engine compartment”.
The arrangement of the indicator lights depends on the model version. The
symbols shown in the following functional description are to be found as indicator
lights in the instrument cluster.
Operational faults are shown in the instrument cluster as red symbols (priority 1 -
danger) or yellow symbols (priority 2 - warning).
Turn signal system
Either the left or right indicator light flashes depending on the position of the turn
signal lever.
The indicator light flashes at twice its normal rate if a turn signal light fails.
Switching off the hazard warning light system is switched on will cause all of the turn
signal lights as well as both indicator lights to flash.
Further information about the turn signal system page 57.
Instruments and warning lights29
WARNING
Caution
Note
Fog lights*
The warning light comes on when the fog lights are operating page 54.
Main beam
The indicator light comes on when the main beam is selected or also when the
headlight flasher is operated.
Further information about the main beam page 57.
Low beam
The warning light comes on when low beam is selected page 51.
Rear fog light
The warning light comes on when the rear fog lights are operating page 55.
Cruise control system*
The warning light lights up, when operating the speed regulating system.
Bulb failure
The warning light comes on if a bulb is faulty:
up to 2 seconds after the ignition is switched on,
when switching on the defective light bulb.
The following text e.g will be displayed in the information display*:
Check front right dipped beam!
The rear side lights and the licence plate lighting require several light bulbs. The indicator light only lights up if all light bulbs of the licence plate lighting or the parking
light (in one rear light unit) are defective. Check regularly the function of the light
bulbs.
Diesel particle filter* (diesel engine)
If the warning light comes on, this means that soot has accumulated in the diesel
particle filter because of the frequent short distances.
In order to clean the diesel particle filter, the vehicle should be dr iven at an even speed
of at least 60 km/h at engine speeds of 1 800 - 2 500 rpm for at least 1 5 minutes or until
the warning light goes out with the 4th or 5th gear engaged (automatic gearbox: position S) when the traffic situation permits it. This increases the exhaust temperature and
the soot deposited in the diesel particle filter is burnt.
Always pay attention to the valid speed limits .
The warning light goes out after the successful cleaning of the diesel particle filter.
If the filter is not properly cleaned, the warning light does not go out and the
warning light begins to flash. In the information display* appears Diesel-particle: Owner's manual. Afterwards the engine control unit shifts the engine into the emergency mode, which only has a reduced power output. After switching the ignition off
and on again the warning light comes on.
Have the vehicle inspected without delay by your specialist garage.
If you do not pay attention to the warning light coming on and the corre-
sponding descriptions and warning notes, this may result in injuries or major
vehicle damage.
Always adjust your speed to suit weather, road, region and traffic condi-
tions. The route indicated by the warning light must not tempt you to disregard
the national regulations for road traffic.
As long as the warning light li ghts up, o ne m ust t ake i nto a cco unt a n in creas ed f uel
consumption and in certain circumstances a power reduction of the engine.
Further information about diesel particle filter page 173.
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Loading...
+ 245 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.