Page 1
SIMPLY CLEVER
ŠkodaOctavia
OWNER´ S MANUAL
Page 2
A5_19_01_06.indd 2A5_19_01_06.indd 2 3.7.2006 14:26:343.7.2006 14:26:34
Page 3
Introduction
You have opted for a Škoda - our sincere thanks for your confidence in us.
Your new Škoda offers you a vehicle featuring the most modern engineering and a wide range of equipment
which you will undoubtedly wish to use to the full during your daily motoring. That is why, we recommend
that you read this Owner's Manual attentively to enable you to become familiar with your car and all that it
offers as quickly as possible.
Please do not hesitate to contact your specialist garage or importer should you have any further questions
or any problems regarding your vehicle which may arise. He will be ready at any time to receive your questions, suggestions and criticisms.
Any national legal provisions which vary from the information contained in this Owner's Manual take precedence over the information contained herein.
We wish you much pleasure with your Škoda and pleasant motoring at all times.
Your Škoda Auto
s24s.book Page 1 Thursday, November 24, 2005 12:27 PM
Page 4
Introduction2
On-board literature
The on-board literature for your vehicle consists of this “Owner's
Manual” as well as the brochures “Brief instruction”, “Service
schedule”, “Tech nical data” and “Help on the road”. There can
also be a variety of other additional operating manuals and
instructions on-board (e.g. an operating manual for the radio)
depending on the vehicle model and equipment.
If one of the publications listed above is missing, please contact
a Škoda dealer immediately, where one will be glad to assist you
in such matters.
One should note that the details given in the vehicle's
papers always take precedence over those in the Owner's
Manual.
Owner's Manual
This Owner's Manual describes the current scope of equip-
ment. Certain items of equipment listed are only installed later on
and only envisaged for particular markets. The illustrations can
differ in minor details from your vehicle; they are only intended for
general information.
In addition to information regarding all the controls and equipment, the Owner's Manual also contains important information
regarding care and operation for your safety and also to retain the
value of your vehicle. To provide you with valuable tips and aids.
You can learn how you can operate your vehicle safely,
economically and in an environmentally conscious way.
For safety reasons, please also pay attention to the information on accessories, modifications and replacement of parts
⇒ page 270.
The other chapters of the Owner's Manual are also important,
however, for proper treatment of your car - in addition to regular
care and maintenance - helps to retain its value and in many
cases is also one of the conditions for possible warranty claims.
The Brief instruction
includes an overview of the most important controls of your
vehicle.
The Service schedule
contains:
• Vehicle data,
• Service intervals,
• Overview of the service work,
• Service proof,
• Confirmation of mobility warranty,
• important information on the warranty.
The confirmations of the carried out service work are one of the
conditions for possible warranty claims.
Please always present the Service schedule when you take your
car to a Škoda dealer.
If the Service schedule is missing or worn, please contact your
Škoda dealer, where your car is serviced regularly. You will
receive a duplicate, in which the previously carried out service
work are confirmed.
Help on the road
contains the addresses and telephone numbers of Škoda
Importers.
s24s.book Page 2 Thursday, November 24, 2005 12:27 PM
Page 5
Introduction 3
Technical Data
includes the most important identification data of your vehicle.
s24s.book Page 3 Thursday, November 24, 2005 12:27 PM
Page 6
Introduction4
s24s.book Page 4 Thursday, November 24, 2005 12:27 PM
Page 7
Contents 5
Contents
Layout of this Owner's Manual
(explanations)
. . . . . . . . . . . . . . . . . . .
Using the system . . . . . . . . . . . . . . .
Cockpit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
An overview . . . . . . . . . . . . . . . . . . . . . . . . . .
Instruments and Indicator/Warning Lights
General view of the instrument cluster . . . . . .
Engine revolutions counter . . . . . . . . . . . . . . .
Coolant temperature gauge . . . . . . . . . . . . . .
Fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . .
Counter for distance driven . . . . . . . . . . . . . .
Service Interval Display . . . . . . . . . . . . . . . . .
Digital clock . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-functional indicator (onboard computer)*
Information display* . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigation system* . . . . . . . . . . . . . . . . . . . .
Auto Check Control . . . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning lights . . . . . . . . . . . . . . . . . . . . . . . . .
Unlocking and locking . . . . . . . . . . . . . . . . . .
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key with light* . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the battery of the radio remote
control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic immobiliser . . . . . . . . . . . . . . . . . .
Child safety locks . . . . . . . . . . . . . . . . . . . . . .
Central locking system . . . . . . . . . . . . . . . . . .
Remote control* . . . . . . . . . . . . . . . . . . . . . . .
Synchonisation of the remote control . . . . . . .
Anti-theft alarm system* . . . . . . . . . . . . . . . . .
Power windows* . . . . . . . . . . . . . . . . . . . . . . .
Electric sliding/tilting roof* . . . . . . . . . . . . . . .
Lights and Visibility . . . . . . . . . . . . . . . . . . . .
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interior lighting . . . . . . . . . . . . . . . . . . . . . . . .
Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield wiper and wash system . . . . . . . .
Rear-view mirror . . . . . . . . . . . . . . . . . . . . . .
Seats and Stowage . . . . . . . . . . . . . . . . . . . .
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting front seats electrically* . . . . . . . . . .
Head restraints . . . . . . . . . . . . . . . . . . . . . . . .
Heating the front seats* . . . . . . . . . . . . . . . . .
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage compartment . . . . . . . . . . . . . . . . . .
Net partition (Estate)* . . . . . . . . . . . . . . . . . . .
Roof rack* . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holder . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note holder . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cigarette lighter*, power sockets . . . . . . . . . .
Storage compartments . . . . . . . . . . . . . . . . . .
Heating and air conditioning system . . . . .
Heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climatic* (semi-automatic air conditioning
system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Climatronic* (automatic air conditioning) . . . .
Auxiliary heating (auxiliary heating and
ventilation)* . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting-off and Driving . . . . . . . . . . . . . . . . .
Setting steering wheel position . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting engine . . . . . . . . . . . . . . . . . . . . . . . .
Switching the engine off . . . . . . . . . . . . . . . .
Shifting (manual gearbox) . . . . . . . . . . . . . . .
Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear parking aid* . . . . . . . . . . . . . . . . . . . . . .
Front and rear parking aid* . . . . . . . . . . . . . .
Cruise control system (CCS)* . . . . . . . . . . . .
Automatic gearbox . . . . . . . . . . . . . . . . . . . . .
6-speed automatic gearbox* . . . . . . . . . . . . .
Automatic gearbox DSG . . . . . . . . . . . . . . .
Automatic gearbox DSG* . . . . . . . . . . . . . . .
Communication . . . . . . . . . . . . . . . . . . . . . . .
Multifunction steering wheel* . . . . . . . . . . . . .
Universal telephone preinstallation with voice
control* . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phone Phonebook* . . . . . . . . . . . . . . . . . . . .
Bluetooth™* . . . . . . . . . . . . . . . . . . . . . . . . .
Mobile phones and two-way radio systems . .
The CD changer* . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Passive Safety . . . . . . . . . . . . . . . . . . . . . . . .
Basic information . . . . . . . . . . . . . . . . . . . . . .
Correct seated position . . . . . . . . . . . . . . . . .
Seat belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Why seat belts? . . . . . . . . . . . . . . . . . . . . . . .
The physical principle of a frontal collision . .
8
9
11
11
13
13
14
14
14
15
15
16
17
18
23
25
26
26
28
30
42
42
43
44
45
45
46
52
53
54
56
59
63
63
70
72
75
79
82
82
84
87
88
89
91
92
99
102
103
104
105
106
108
119
119
123
128
134
138
138
139
140
141
142
143
144
145
146
149
149
156
156
163
163
165
171
173
175
176
177
177
177
179
183
183
184
s24s.book Page 5 Thursday, November 24, 2005 12:27 PM
Page 8
Contents6
Important safety information regarding the use
of seat belts . . . . . . . . . . . . . . . . . . . . . . . . . .
How are seat belts correctly fastened? . . . . .
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . .
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . .
Description of the airbag system . . . . . . . . . .
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . .
Side airbags* . . . . . . . . . . . . . . . . . . . . . . . . .
Head airbags* . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating an airbag . . . . . . . . . . . . . . . . . .
Transporting children safely . . . . . . . . . . . . .
What you should know about transporting
children! . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Child seat . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Attaching child seat using the “ISOFIX” system
Driving Tips . . . . . . . . . . . . . . . . . . . . . .
Intelligent Technology . . . . . . . . . . . . . . . . . .
Electronic stability programme (ESP)* . . . . . .
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake booster . . . . . . . . . . . . . . . . . . . . . . . .
Antilock brake system (ABS) . . . . . . . . . . . . .
Brake Assist* . . . . . . . . . . . . . . . . . . . . . . . . .
Uphill-Start off-Assist* . . . . . . . . . . . . . . . . . .
Electromechanical power steering . . . . . . . . .
Tyre inflation pressure-control system* . . . . .
Driving and the Environment . . . . . . . . . . . .
The first 1 500 kilometres and then afterwards
Catalytic converter . . . . . . . . . . . . . . . . . . . . .
Driving in an economical and environmentally
conscious manner . . . . . . . . . . . . . . . . . . . . .
Environmental compatibility . . . . . . . . . . . . . .
Motoring abroad . . . . . . . . . . . . . . . . . . . . . . .
Avoiding damage to your vehicle . . . . . . . . . .
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . .
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . .
Detachable ball head* . . . . . . . . . . . . . . . . . .
General Maintenance . . . . . . . . . .
Taking care of your vehicle and cleaning the
vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Care of the exterior of vehicle . . . . . . . . . . . .
Care of the interior of vehicle . . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Petrol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diesel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refuelling . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspecting and Replenishing . . . . . . . . . . . .
Engine compartment . . . . . . . . . . . . . . . . . . .
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooling system . . . . . . . . . . . . . . . . . . . . . . .
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . .
The battery . . . . . . . . . . . . . . . . . . . . . . . . . .
Windscreen Wiper and Washer System . . . .
Wheels and Tyres . . . . . . . . . . . . . . . . . . . . .
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories, changes and replacement of
parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories and replacement parts . . . . . . .
Technical changes . . . . . . . . . . . . . . . . . . . . .
Breakdown assistance . . . . . . . .
Breakdown assistance . . . . . . . . . . . . . . . . .
First-aid box* and warning triangle* (Octavia)
First-aid box* and warning triangle* (Estate
car) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fire extinguisher* . . . . . . . . . . . . . . . . . . . . .
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . .
Tyre repair kit* . . . . . . . . . . . . . . . . . . . . . . . .
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . .
Changing a wheel . . . . . . . . . . . . . . . . . . . . .
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . .
Tow-starting and towing vehicle . . . . . . . . . .
Fuses and light bulbs . . . . . . . . . . . . . . . . . .
Electric fuses . . . . . . . . . . . . . . . . . . . . . . . . .
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data . . . . . . . . . . . . . . . . . .
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Identification data . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
185
186
188
190
190
192
195
197
199
202
202
206
210
213
213
213
216
217
218
218
219
219
220
221
221
222
223
227
228
228
229
229
231
233
233
233
233
239
242
242
242
245
247
247
250
253
256
258
262
263
263
270
270
270
273
273
273
273
274
274
275
275
276
281
283
288
288
294
303
303
303
305
s24s.book Page 6 Thursday, November 24, 2005 12:27 PM
Page 9
Contents 7
s24s.book Page 7 Thursday, November 24, 2005 12:27 PM
Page 10
Layout of this Owner's Manual (explanations)8
Layout of this Owner's Manual (explanations)
The Owner's Manual has been systematically designed, in order to make
it easy for you to find and absorb the information you require.
Chapters, table of contents and subject index
The text of the manual are divided into relatively short sections which are
combined into easy-to-read chapters. The chapter you are reading at any
particular moment is highlighted at the bottom right of the page.
The Table of contents is arranged according to the chapters and the
detailed Subject index at the end of the Owner's Manual helps you to
rapidly find the information you are looking for.
Sections
The majority of Sections apply to all models.
Since there is a wide range of different equipment and options available it
is clearly unavoidable, despite dividing the contents into sections, that
mention may be made of equipment which is not fitted to your vehicle.
Equipment which is marked * is only standard on certain vehicle model
versions or only suppliable as optional equipment for certain models.
Brief information and instructions
Each section has a Heading.
This is followed by Brief information (in large italic lettering), which tells
you the subject which is dealt with in this section.
Most of the illustrations are accompanied by an Instruction (in relatively
large letters) which explains to you in a straightforward way the action you
have to take. Work steps which have to be carried out are illustrated with
a hyphen.
Notes
All four kinds of notes, which are used in the text, are always stated at the
end of the respective section.
WARNING
The most important notes are marked with the heading Warning.
These Warning notes draw your attention to a serious risk of accident or injury. While reading the text you will frequently encounter
a double arrow followed by a small warning symbol. This symbol is
intended to draw your attention to a Warning note at the end of the
section to which you must pay careful attention.
Caution
A Caution note draws your attention to the possibility of damage to your
vehicle (e.g. damage to gearbox), or points out general risks of an accident .
For the sake of the environment
An Environmental note draws your attention to environmental protection
aspects. This is where you will, for example, find tips aimed at reducing
your fuel consumption.
Note
A normal Note draws your attention in a general way to important information.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the
direction of travel of the vehicle.
s24s.book Page 8 Thursday, November 24, 2005 12:27 PM
Page 11
9
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Using the system
s24s.book Page 9 Thursday, November 24, 2005 12:27 PM
Page 12
Cockpit10
Fig. 1 Certain items of equipment shown in the illustration are only fitted to particular model versions or are optional items of equipment.
s24s.book Page 10 Thursday, November 24, 2005 12:27 PM
Page 13
Cockpit 11
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Cockpit
An overview
This general view is designed to help you to quickly
become familiar with the instruments, gauges and
controls.
Electric power-operated window* . . . . . . . . . . . . . . . . . . . .
Electric exterior mirror adjustment* . . . . . . . . . . . . . . . . . . .
Air outlet vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever for the multi-functional switch:
− Turn signal light, headlight and parking light, headlight
flasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Speed regulating system* . . . . . . . . . . . . . . . . . . . . . . . .
Steering wheel:
− with horn
− with driver airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− with pushbuttons for radio and mobile phone* . . . . . . . .
Instrument cluster: Instruments and indicator lights . . . . . .
Lever for the multi-functional switch:
− Multi-functional indicator* . . . . . . . . . . . . . . . . . . . . . . . .
− Windshield wiper and wash system . . . . . . . . . . . . . . . . .
Control dial for heating on the driver's seat* . . . . . . . . . . . .
Air outlet vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch for hazard warning lights . . . . . . . . . . . . . . . . . . . . .
Storage compartment on the dash panel . . . . . . . . . . . . . . .
Radio*
Control dial for heating on the front passenger seat* . . . . .
Storage compartment on the front passenger side . . . . . . .
Switch for the front passenger airbag* (in front passenger
stowage compartment) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front passenger airbag* . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse carrier (on side of dash panel) . . . . . . . . . . . . . . . . . .
Light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control dial for the instrument lighting and control dial for the
headlight beam range regulation . . . . . . . . . . . . . . . . . . . .
Bonnet release lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage compartment on the driver's side . . . . . . . . . . . . .
Lever for adjusting the steering wheel . . . . . . . . . . . . . . . .
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Operating controls for the heating . . . . . . . . . . . . . . . . .
− Operating controls for Climatic* . . . . . . . . . . . . . . . . . . .
− Operating controls for Climatronic* . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Switch for the ESP* . . . . . . . . . . . . . . . . . . . . . . . . . . . .
− Switch for TCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front and rear parking aid* . . . . . . . . . . . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Gearshift lever (manual gearbox) . . . . . . . . . . . . . . . . . .
− Selector lever (6-speed automatic gearbox)* . . . . . . . . .
− Selector lever (automatic DSG)* . . . . . . . . . . . . . . . . . .
Tyre inflation pressure-control system* . . . . . . . . . . . . . . .
Depending on equipment fitted:
− Rear ashtray - high centre console* . . . . . . . . . . . . . . . .
A
1
56
A
2
80
A
3
122
A
4
68
146
A
5
192
163
A
6
13
A
7
18
75
A
8
88
A
9
122
A
10
68
A
11
110
A
12
A
13
88
A
14
108
A
15
200
A
16
192
A
17
288
A
18
63
A
19
67, 67
A
20
247
A
21
109
A
22
138
A
23
139
A
24
119
123
128
A
25
213
215
A
26
145
A
27
142
150
157
A
28
220
A
29
106
s24s.book Page 11 Thursday, November 24, 2005 12:27 PM
Page 14
Cockpit12
− Storage compartment* . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator light for a switched off front seat passenger
airbag* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note
• Equipment which is marked * is only standard on certain vehicle model
versions or only suppliable as optional equipment for certain models.
• Vehicles with factory-fitted radio, mobile phone, navigation system,
CD player etc. are supplied with separate instructions for operating such
equipment.
• The arrangement of the controls and switches and the location of
some items on right-hand drive models may differ from that shown in
⇒ page 10, fig. 1. The symbols on the controls and switches are the same
as for left-hand drive models.
108
A
30
200
s24s.book Page 12 Thursday, November 24, 2005 12:27 PM
Page 15
Instruments and Indicator/Warning Lights 13
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Instruments and Indicator/Warning Lights
General view of the instrument cluster
Engine revolutions counter ⇒ page 14
Coolant temperature gauge ⇒ page 14
Fuel gauge ⇒ page 14
Speedometer
Display:
− with counter for distance driven ⇒ page 15
− with Service Interval Display ⇒ page 16
− with digital clock ⇒ page 17
− with Multi-functional indicator* ⇒ page 18
− with Information display* ⇒ page 23
Clock-set button / reset button
When the lights are switched on, the instrument cluster is illuminated.
Fig. 2 Instrument cluster
A
1
A
2
A
3
A4A5A
6
s24s.book Page 13 Thursday, November 24, 2005 12:27 PM
Page 16
Instruments and Indicator/Warning Lights14
Engine revolutions counter
The start of the red zone in the revolutions counter ⇒ page 13, fig. 2
indicates the maximum permissible engine speed for all gears for an
engine which has been run in and operating at a normal temperature. You
should shift into the next higher gear before this red zone is reached, or
move the selector lever into position D if your car is fitted with an automatic
gearbox.
One should shift to the next lower gear at the latest when the engine is no
longer running smoothly.
Avoid high engine speeds during the running-in period ⇒ page 221.
Caution
The needle of the revolutions counter must on no account move into the
red zone of the scale - risk of engine damage!
For the sake of the environment
Shifting up early helps you save fuel and reduce the operating noise of
your vehicle.
Coolant temperature gauge
The coolant temperature gauge ⇒ page 13, fig. 2 operates only when
the ignition is switched on.
In order to avoid any damage to the engine, please pay attention to the
following notes regarding the temperature ranges:
Cold range
If the pointer is still in the left-hand area of the scale it means that the
engine has not yet reached its operating temperature. Avoid running at
high engine speeds, at full throttle and at severe engine loads.
The operating range
The engine has reached its operating temperature as soon as the pointer
moves into the mid-range of the scale. The pointer may also move further
to the right at high engine loads and high outside temperatures. This is not
critical provided the warning symbol in the instrument cluster does not
flash.
If the symbol in the instrument cluster flashes it means that either the
coolant temperature is too high or the coolant level is too low. Please
refer to the guidelines ⇒ page 35, “Coolant temperature/coolant level ”.
WARNING
Pay attention to the warning notes ⇒ page 248, “Working in the
engine compartment” before opening the bonnet and inspecting
the coolant level.
Caution
Additional headlights and other attached components in front of the fresh
air inlet impair the cooling efficiency of the coolant. There is then a risk of
the engine overheating at high outside temperatures and high engine
loads!
Fuel gauge
The fuel gauge ⇒ page 13, fig. 2 only operates when the ignition is
switched on.
A
1
A2A
3
s24s.book Page 14 Thursday, November 24, 2005 12:27 PM
Page 17
Instruments and Indicator/Warning Lights 15
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The fuel tank has a capacity of about 55 litres (on vehicles with four-wheel
drive approx. 60 litres). The warning symbol in the instrument cluster
lights up when the pointer reaches the reserve marking. There are now
about 8 litres of fuel remaining in the tank. This symbol is a reminder for
you, that you must refuel.
The following will be displayed in the information display*:
Please refuel! (Please refuel!)
A peep sounds as an additional warning signal.
Caution
Never run the fuel tank completely empty! An irregular fuel supply can
result in poor ignition or misfiring. Unburnt fuel may get into the exhaust
system and damage the catalytic converter.
Speedometer
Warning against excessive speeds*
An acoustic warning signal will sound when the vehicle speed exceeds
120 kilometres per hour. The acoustic warning signal will switch off again
when the vehicle speed goes below this speed limit.
Note
This function is only valid for some countries.
Counter for distance driven
The distance which you have driven with your vehicle is shown in kilometers (km). On certain model versions, the readout is shown in “miles”.
The kilometer counter for distance driven is shown on the display when
the ignition is switched off. The trip counter for distance driven is shown
on the display after switching on the ignition. You can then switch over to
the counter display with the reset button.
Reset button
By briefly pressing the reset button ⇒ page 13, fig. 2 you can switch
over from the trip counter to the kilometer counter. In order to recognize
which counter for the distance driven is shown on the display at that
moment, trip ⇒ fig. 3 appears after the trip counter.
If you hold the reset button pressed for about 1 second, the trip counter
is set back to zero.
If you hold the reset button pressed for longer than 2 seconds when
the ignition is switched on, a display regarding the kilometers still to be
Fig. 3 Display: Trip
counter for distance
driven
A
6
A6A
6
s24s.book Page 15 Thursday, November 24, 2005 12:27 PM
Page 18
Instruments and Indicator/Warning Lights16
driven and the days until the following service interval (for this the trip
counter is not set back) appears ⇒ page 16.
Counter for distance driven (trip)
The counter for distance driven indicates the total distance in kilometers
or miles which the vehicle has been driven.
Trip counter for distance driven
The trip counter indicates the distance which you have driven since this
counter was last reset - in steps of 100 metres or 1/10 of a mile.
Fault display
dEF will appear as a constant text in the display if there is a fault in the
instrument cluster. Have the fault rectified as soon as possible by a
specialist workshop.
WARNING
Never seek to adjust the trip counter for distance driven while
driving for safety reasons!
Note
On vehicles without multi-functional indicator or information display, both
counts of the counters are shown simultaneously on the display.
Service Interval Display
Depending on the equipment installed in the vehicle, the text can differ
slightly on the display.
Service Interval Display
A key symbol
appears in the counter display for distance driven about
15 days before reaching the due date for the service ⇒ fig. 4. The
remaining distance to be driven will be indicated for 10 seconds next to
the key symbol and then the remaining number of days to the due date for
the service inspection.
The following will be displayed in the information display*:
Service in ... km or... days
The kilometre indicator or the days indicator reduces in steps of 100 km
or days until the service due date is reached.
The following text appears as a flashing key symbol
as soon as the
due date for the service is reached.
Fig. 4 Service Interval
Display: Note
s24s.book Page 16 Thursday, November 24, 2005 12:27 PM
Page 19
Instruments and Indicator/Warning Lights 17
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The following will be displayed in the information display*:
Service now!
The display disappears within 20 seconds after switching on the ignition.
The trip counter is also displayed after pressing the reset button for the trip
counter (for more than 1 second).
Display regarding the distance and days until the following service
interval
You can have the distance still to be driven and the days until the following
service interval displayed at any time as follows:
• Switch on the ignition and press the reset button ⇒ page 13, fig. 2
for more than 2 seconds.
A key symbol is displayed on the display of the counter for the
distance driven. The remaining distance to be driven will be indicated for
10 seconds next to the key symbol and then the remaining number of days
to the due date for the service inspection.
Resetting Service Interval Display
We recommend having this resetting performed by a specialist garage.
Specialist garage:
• resets the memory of the display after the appropriate inspection
• makes an entry in the Service schedule
• affix the sticker with the entry of the following service interval to the
side of the dash panel on the driver's side.
The service interval displays can also be reset as follows by using the
reset button ⇒ page 13, fig. 2 on the trip counter:
• Switch off the ignition, press the reset button of the trip counter for
distance driven and hold it down.
• Switch the ignition on and release the reset button. Now turn the reset
button to the right. The service interval displays are reset.
Caution
We recommend that you do not reset the Service Interval Display yourself
otherwise this can result in the service interval display being incorrectly
set, which may also result in problems with operation of your vehicle.
Note
• Never reset the display between service intervals otherwise this may
result in incorrect readouts.
• Information is retained in the Service Interval Display also after the
battery of the vehicle is disconnected.
• It is necessary to re-code the Service Interval Display if a new instru-
ment cluster is installed during repair work. This work is carried out by a
specialist garage.
• The data displayed is the same after resetting the display with flexible
service intervals (QG1) using the reset button as that for a vehicle with
fixed service intervals (QG2). We therefore recommend having the
Service Interval Display reset only by a Škoda dealer who is familiar with
the procedure for resetting the display with a vehicle system tester.
• Please refer to the brochure Service schedule for extensive informa-
tion about the service intervals.
Digital clock
A clock-set button is installed on the bottom left beside the
speedometer for adjusting the clock ⇒ page 13, fig. 2.
Set hours
– Turn the reset button to the left.
A
6
A
6
A
6
s24s.book Page 17 Thursday, November 24, 2005 12:27 PM
Page 20
Instruments and Indicator/Warning Lights18
Setting minutes
– Turn the reset button to the right.
WARNING
The clock should not be adjusted while driving for safety reasons
but only when the vehicle is stationary!
Multi-functional indicator (onboard
computer)*
Introduction
The multi-functional indicator appears in the display ⇒ fig. 5 or in the information display ⇒ page 23, fig. 10 depending on the equipment fitted to
your vehicle.
The multi-functional indicator offers you a range of useful information.
Note
In certain national versions the displays appear in the Imperial system of
measures.
Memory
The multi-functional indicator is equipped with two automatic memories.
The selected memory is di splayed in the middle of the display field ⇒ fig. 5.
The data of the single-trip memory (memory 1) is shown if a 1 appears in
the display. A 2 shown in the display means that data relates to the total
distance memory (memory 2).
Switching of the memory takes place with the button ⇒ page 19, fig. 6.
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment
the ignition is switched on until it is switched off. New data will also flow
The outside temperature ⇒ page 20
Current fuel consumption ⇒ page 20
Average fuel consumption ⇒ page 20
Range ⇒ page 21
Distance driven ⇒ page 21
Average speed ⇒ page 21
Driving time ⇒ page 21
Warning against excessive speeds* ⇒ page 22
Fig. 5 Multi-functional
indicator
A
B
s24s.book Page 18 Thursday, November 24, 2005 12:27 PM
Page 21
Instruments and Indicator/Warning Lights 19
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
into the calculation of the current driving information if the trip is continued
within 2 hours after switching off the ignition. The memory will be automatically erased, on the other hand, if the trip is interrupted for more than
2 hours.
Total-trip memory (memory 2)
The total distance driven memory gathers data from any number of individual journeys up to a total of 99 hours and 59 minutes driving or 9.999
kilometres driven. The memory is deleted when either of these limits is
reached and the calculation starts from anew.
The total-trip memory will not, contrary to the single-trip memory, be
deleted after a period of interruption of driving of 2 hours.
Note
All information in the memory is erased if the battery of the vehicle is
disconnected.
Using the system
The rocker switch and the button are located in the grip of
the window wiper lever ⇒ fig. 6.
Selecting the memory
– Repeated short-term pressing of the button allows one to
select the individual memories.
Selecting the functions
– Press the rocker switch up or down. This will cause the
individual functions of the multi-functional indicator to appear
in the display one after the other.
Setting function to zero
– Select the memory you want.
– Press button for more than 1 second.
Fig. 6 Multi-functional
indicator: Controls
AAA
B
A
B
AAA
B
s24s.book Page 19 Thursday, November 24, 2005 12:27 PM
Page 22
Instruments and Indicator/Warning Lights20
The following readouts of the selected memory will be set to zero by
button :
• average fuel consumption,
• distance driven,
• average speed,
• Driving time.
You can only operate the multi-functional indicator when the ignition is
switched on. After the ignition is switched on, the function displayed is the
one which you last selected before switching off the ignition.
If the outside temperature drops below +4 °C, the outside temperature
indicator with a snow flake symbol appears. The symbol warns the driver
of the possible danger of ice on the road. After the rocker switch is
pressed, the function displays the one which you last selected before
switching off the ignition.
The outside temperature
The outside temperature appears in the display when the ignition is
switched on.
The correct outside temperature will be indicated with a delay of 5
minutes. If the vehicle is stationary (or driven at a very low speed) the
temperature indicated may be slightly higher than the actual outside
temperature because of heat radiated by the engine.
If the outside temperature drops below +4 °C, a snow flake symbol
(warning signal for ice on the road) appears before the temperature indicator ⇒ fig. 7 and a warning signal sounds.
WARNING
Do not only rely upon the information given on the outside temperature display that there is no ice on the road. Please note that black
ice may also be present on the road surface even at temperatures
around +4 °C - warning, drive with care!
Current consumption
The current fuel consumption level is shown in the display in litres/100 km.
This information can help you to adapt your style of driving to the fuel
consumption you wish to achieve.
The display appears in litres/hour if the vehicle is stationary or driving at a
low speed.
Average fuel consumption
The average fuel consumption since the memory was last erased is
shown in the display in litres/100 km ⇒ page 18. This information can help
A
B
A
A
Fig. 7 Multi-functional
indicator: the outside
temperature
s24s.book Page 20 Thursday, November 24, 2005 12:27 PM
Page 23
Instruments and Indicator/Warning Lights 21
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
you to adapt your style of driving to the fuel consumption you wish to
achieve.
If you wish to determine the average fuel consumption over a certain
period of time you must first erase the memory at the start of the new
measurement using the button ⇒ page 19, fig. 6. A zero appears in the
display for the first 100 m you drive after erasing the memory.
The indicated value will be updated every 5 seconds while you are driving.
Note
The amount of fuel consumed will not be indicated.
Range
The estimated range in kilometres is shown on the display. It indicates the
distance you can still drive with your vehicle based on the present level of
fuel in the tank for the same style of driving. The readout is shown in steps
of 10 km.
The fuel consumption for the last 50 km is taken as a basis for calculating
the range. If you drive in a more economical manner from this moment on,
the range will be increased accordingly.
You first drive 50 km if the readout is reset (after disconnecting the
battery) before a new readout for the range is displayed.
Distance driven
The distance driven since the memory was last erased appears in the
display ⇒ page 18. If you wish to calculate the distance driven from a
particular time of day you must first erase the memory at this moment in
time by pressing the button ⇒ page 19, fig. 6.
The maximum distance indicated in both switch positions is 9999 km. The
indicator is set back to null if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the
display in km/hour ⇒ page 18. If you wish to determine the average speed
over a certain period of time you must first erase the memory at the start
of the new measurement using the button ⇒ page 19, fig. 6.
A zero appears in the display for the first 100 m you drive after erasing the
memory.
The indicated value will be updated every 5 seconds while you are
driving.
Driving time
The driving time which has elapsed since the memory was last erased,
appears in the display ⇒ page 18. If you wish to calculate the driving time
from a particular time of day you must first erase the memory at this
moment in time by pressing the button ⇒ page 19, fig. 6.
The maximum distance indicated in both memories is 99 hours and 59
minutes. The indicator is set back to null if this period is exceeded.
A
B
A
B
ABA
B
s24s.book Page 21 Thursday, November 24, 2005 12:27 PM
Page 24
Instruments and Indicator/Warning Lights22
Warning against excessive speeds*
Warning against excessive speeds
1)
This function enables you to set a speed limit, e.g. if you drive in town. A
text in the display is intended to draw your attention to the fact that you
have exceeded the set speed limit.
You can set the desired speed limit as follows:
• Select the menu Speed warning --- km/h (warning at --- km/h).
• You can drive at the desired speed, e.g. 50 km/h
• Press the button ⇒ fig. 9 - Speed warning 50 km/h (warning at 50
km/h) is shown on the display.
If you now exceed the set speed limit, Speed 50 km/h exceeded (speed
50 km/h exceeded) will be shown on the display. This display will be
shown until you have reduced the speed to the set speed limit.
A peep sounds as an additional warning signal.
The set speed limit remains stored in the memory, also when the ignition
is switched off and on; it can only be erased by pressing the button for
more than 1 second.
Fig. 8 Speed setting
Fig. 9 Multi-functional
indicator: Controls
1)
Valid for vehicles with information display.
ABA
B
s24s.book Page 22 Thursday, November 24, 2005 12:27 PM
Page 25
Instruments and Indicator/Warning Lights 23
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Information display*
Introduction
The information display provides you with information in a convenient way
concerning the current operating state of your vehicle. The information
system also provides you with data (depending on the equipment installed
in the vehicle) relating to the radio, mobile phone, multi-functional indicator, navigation system and automatic gearbox.
Certain functions and operating conditions are always being checked on
the vehicle when the ignition is switched on and also while driving.
Functional faults, if required repair work and other information are indicated by red symbols ⇒ page 27 and yellow symbols ⇒ page 28.
Lighting up of these symbols is combined with an acoustic warning signal.
Information and texts giving warnings are also shown in the display
⇒ page 30.
The display of text is possible in the following languages:
Czech, English, German, French, Italian, Spanish, Portuguese.
You can select the desired language in the setting menu ⇒ page 28.
The following information can be shown in the display (depending on the
equipment installed on the vehicle):
Fig. 10 Instrument
cluster: Information
display
Main menu ⇒ page 24
Door, luggage compartment door and bonnet ajar
warning
⇒ page 25
Service Interval Display ⇒ page 16
Selector lever positions of the 6-speed automatic
gearbox
⇒ page 150
Selector lever positions of the automatic DSG ⇒ page 157
s24s.book Page 23 Thursday, November 24, 2005 12:27 PM
Page 26
Instruments and Indicator/Warning Lights24
Main menu
– You can activate the MAIN MENU by pressing the rocker
switch ⇒ fig. 12 for more than 1 second.
– You can select the menu through the rocker switch . When
the pushbutton is briefly pressed, the information you have
selected is displayed.
You can select the following information (depending on the equipment
installed on the vehicle):
MF Display ⇒ page 18
The outside temperature
Current consumption
Average fuel consumption
Range
Distance driven
Average speed
Driving time
Warning against excessive speeds
Audio ⇒ page 25
Navigation ⇒ page 26
Telephone ⇒ page 167
Vehicle status ⇒ page 26
Setup ⇒ page 28
Time
Winter tyres
Language
Units
Lights & Vision
Aux. Heating (auxiliary heating)
Back
Fig. 11 Information
display: Menu
Fig. 12 Information
display: Controls
AAAAA
B
s24s.book Page 24 Thursday, November 24, 2005 12:27 PM
Page 27
Instruments and Indicator/Warning Lights 25
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Display off
After selecting the menu Display off the display is switched off. Press
rocker switch for at least 1 second to switch the display on again.
The menu Audio is only displayed when the Radio* is switched on.
The menu Navigation is only displayed when the Navigation* is switched
on.
Aux. Heating (auxiliary heating) is only then displayed, if the vehicle is
fitted with auxiliary heating*.
Note
If you do not activate the information display at that moment, the menu
shifts to one level higher every 10 seconds.
Door, luggage compartment door and bonnet ajar
warning
The door, luggage compartment door and bonnet ajar warning lights up
when at least one of the three items door, luggage compartment or bonnet
are not closed when the ignition is turned on. The symbol indicates which
door is still open or whether the luggage compartment door or bonnet is
not closed ⇒ fig. 13.
The symbol goes out as soon as the doors, luggage compartment door
and bonnet are completely closed.
As an additional warning signal, a 3 time peep sounds if the car is driven
at a speed of more than 6km/hour and if the door, engine or luggage
compartment door is open.
Audio
These displays appear in addition to the normal information in the radio
display.
A
A
Fig. 13 Information
display: Door warning
Fig. 14 Information
display: Radio display
s24s.book Page 25 Thursday, November 24, 2005 12:27 PM
Page 28
Instruments and Indicator/Warning Lights26
Operation of the radio system is described in separate operating instructions to be found in the on-board literature.
Navigation system*
The controls for the navigation system, radio, CD player are located in the
centre console on both sides of the monitor screen. Navigation data is
also shown in the information display of the instrument cluster.
Information and warning texts are displayed preferentially when the navigation system is switched on.
Operation of the navigation system is described in separate operating
instructions to be found in the on-board literature.
Auto Check Control
Vehicle condition
The Auto Check Control carries out a check of certain functions and
vehicle components. The check is performed constantly when the ignition
is switched on, both when the vehicle is stationary, as well as when
driving.
Operational faults, urgent repairs, service work or other information
appear in the display of the instrument cluster. The displays are shown
with a red or yellow light symbol depending on the priority of the message.
The red symbols indicate danger (priority 1) while the yellow symbols indicate a warning (priortity 2). Information for the driver may also appear in
addition to the symbols ⇒ page 30.
There is at least one error message to be read when the term Vehicle
status is flashing in the main menu. After selecting this menu the first of
the error messages is displayed. If there are several error messages, they
Fig. 15 Information
display: Display of
operational fault
s24s.book Page 26 Thursday, November 24, 2005 12:27 PM
Page 29
Instruments and Indicator/Warning Lights 27
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
are shown on the display under the message e.g. 01/03 ⇒ fig. 15. This
display indicates that the first of a total of three error messages should be
displayed. The respective symbols light up one after the other in an
interval of 5 seconds. Investigate the displayed faults as soon as possible.
As long as the operational faults are not rectified, the symbols are always
indicated again. After the first display, the symbols are indicated without
information for the driver.
If there is no error message, after selecting the menu Vehicle status the
message Status OK is shown on the display.
If a fault occurs, a warning signal will also sound in addition to the symbol
and text in the display:
• Priority 1 - three warning signals
• Priority 2 - one warning signal
Red symbols
A red symbol signals danger.
Proceed as follows if a red symbol is displayed:
– Stop the vehicle.
– Switch the engine off.
– Investigate the function indicated.
– Obtain professional assistance.
Meaning of the red symbols:
Coolant level too low/coolant temperature too high
⇒ page 35
Engine oil pressure too low ⇒ page 37
Fig. 16 Information
display: Oil pressure is
low
s24s.book Page 27 Thursday, November 24, 2005 12:27 PM
Page 30
Instruments and Indicator/Warning Lights28
Three successive warning signals will sound if a red symbol appears.
If several operational faults of priority 1 exist, the symbols appear one
after the other and are each illiminated for about 5 seconds.
Yellow symbols
A yellow symbol signals a warning.
Check the relevant function as soon as possible.
The meaning of the yellow symbols:
One warning signal will sound if a yellow symbol appears.
If several operational faults of priority 2 exist, the symbols appear one
after the other and are each illiminated for about 5 seconds.
Settings
Fig. 17 Information
display: Fuel level low
Fuel level low ⇒ page 36
Check engine oil level,
engine oil sensor faulty
⇒ page 38
Brake pad worn ⇒ page 36
Washer fluid level low ⇒ page 36
Fig. 18 Setting the
clock
s24s.book Page 28 Thursday, November 24, 2005 12:27 PM
Page 31
Instruments and Indicator/Warning Lights 29
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
You can change certain settings by means of the information display. The
current setting is shown on the information display in the respective menu
at the top below the line ⇒ page 28, fig. 18.
You can select the following information (depending on the equipment
installed on the vehicle):
• Time
• Winter tyres
• Language
• Units
• Lights & Vision
• Aux. Heating (auxiliary heating)
• Back
After selecting the menu Back you will reach one level higher in the menu.
Setting clock
Here you can set the time, the time format (12 or 24 hour indicator) and
the time change summer/winter time.
Setting for winter tyre speed
Here you can set at which speed a warning signal should sound. These
functions are used for e.g on winter tyres with the permissible maximum
speed less than the maximum speed of the vehicle ⇒ page 266.
When exceeding the speed, the following is displayed on the information
display*:
Speed warning
Language setting
Here you can set in which language the warning and information texts
should be displayed. After selecting the language, e.g. English, the
following is displayed on the information display:
Language: english set
Setting units
Here you can set the units for temperature, consumption and distance
driven.
Setting lights
Here you can switch on or off the function convenience turn signal
⇒ page 68. Furthermore you can set how long the light should stay on for
the function Coming/Leaving Home ⇒ page 66.
After selecting the menu Factory setting the factory setting is established
again.
s24s.book Page 29 Thursday, November 24, 2005 12:27 PM
Page 32
Instruments and Indicator/Warning Lights30
Warning lights
An overview
The warning lights indicate certain functions or faults.
Fig. 19 Instrument cluster with warning lights
Turn signal lights (to the left) ⇒ page 32
Turn signal lights (to the right) ⇒ page 32
Main beam ⇒ page 32
Low beam ⇒ page 32
Rear fog light ⇒ page 32
Electronic immobiliser ⇒ page 32
Diesel particle filter (diesel engine) ⇒ page 33
Bulbs ⇒ page 33
s24s.book Page 30 Thursday, November 24, 2005 12:27 PM
Page 33
Instruments and Indicator/Warning Lights 31
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
WARNING
• If you do not pay attention to the warning lights coming on and
the corresponding descriptions and warning notes, this may result
in severe body injuries or major vehicle damage.
• The engine compartment of your car is a hazardous area. There
is a risk of injuries, scalding, accidents and fire when working in
the engine compartment, e.g. inspecting and replenishing oil and
other fluids. It is also essential to observe all warnings ⇒ page 248.
Note
• Arrangement of the indicator lights depends on the model and model
version. The symbols shown in the following functional description are to
be found as indicator lights in the instrument cluster.
• Operational faults are shown in the instrument cluster as red symbols
(priority 1 - danger) or yellow symbols (priority 2 - warning).
Electromechanical power steering ⇒ page 33
Control system for exhaust ⇒ page 34
EPC fault light (petrol engine) ⇒ page 34
Glow plug system (diesel engine) ⇒ page 34
Airbag system ⇒ page 35
Coolant temperature/coolant level ⇒ page 35
Brake pad wear* ⇒ page 36
Fluid level in windshield washer system*
⇒ page 36
Fuel reserve ⇒ page 36
Engine oil pressure ⇒ page 37
Bonnet ⇒ page 37
Open door* ⇒ page 37
Engine oil level* ⇒ page 38
Tyre pressure* ⇒ page 38
Selector lever lock* ⇒ page 38
Antilock brake system (ABS) ⇒ page 38
Traction control system (TCS) ⇒ page 39
Electronic stability programme (ESP)* ⇒ page 40
Dynamo ⇒ page 40
Brake system ⇒ page 40
Seat belt warning light* ⇒ page 41
s24s.book Page 31 Thursday, November 24, 2005 12:27 PM
Page 34
Instruments and Indicator/Warning Lights32
Turn signal system
Either the left or right indicator light flashes depending on the position of the turn signal lever.
The indicator light flashes at twice its normal rate if a turn signal light fails.
This does not apply when towing a trailer.
Switching on the hazard warning light system is switched on will cause all
of the turn signal lights as well as both indicator lights to flash.
Further information about the turn signal system ⇒ page 68.
Main beam
The indicator light comes on when the main beam is selected or also
when the headlight flasher is operated.
Further information about the main beam ⇒ page 68.
Low beam
The indicator light comes on when low beam is selected ⇒ page 63.
The rear fog light
The warning light comes on when the rear fog lights are operating
⇒ page 65.
Electronic immobiliser
Data is compared between the ignition key and the control unit when
switching on the ignition. The indicator light will light up for a few
seconds when ignition key authorisation is confirmed.
The warning light will start flashing continuously if a non-authorised ignition key (for example the wrong ignition key) has been used. The engine
cannot be started ⇒ page 45.
It is only possible to start the engine of the vehicle with a Genuine Škoda
key with the matching code.
The following text will be displayed in the information display*:
Immobilizer active
s24s.book Page 32 Thursday, November 24, 2005 12:27 PM
Page 35
Instruments and Indicator/Warning Lights 33
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Diesel particle filter (diesel engine)
In the diesel particle filter the resulting soot particles are
collected and burnt during the combustion of diesel fuel.
Code 7GG on the vehicle data sticker ⇒ fig. 20 indicates that your
vehicle is equipped with a diesel particle filter. The vehicle data
sticker ⇒ page 303, fig. 234 is located on the floor of the luggage
compartment and is also stated in the Service schedule.
The soot particles, which result from the combustion of diesel fuel, are
collected in the diesel particle filter. If the filter is full, the warning light
lights up in the instrument cluster.
The soot particles must be burned in the filter. The combustion is
performed when you are driving at least 60 km/h for 5 to 10 minutes. The
warning light goes out.
If the warning light remains on despite this measure, the following text
appears in the display of the instrument cluster: Engine fault Workshop!.
In this case contact a specialist garage to obtain assistance.
WARNING
Please pay attention to the traffic regulations and speed limits.
Note
It is prohibited to use biofuel and diesel fuel mixture (RME) for vehicles
with diesel engines which are fitted with diesel particle filter.
Bulbs
The warning light comes on for a few seconds after ignition is switched
on and goes out after several seconds.
If the warning light does not go out or comes on when driving, a bulb in the
headlights of the rear parking light or in the brake lights is defective.
The following text e.g will be displayed in the information display*:
Dipped beam front left defective!
A peep sounds as an additional warning signal.
Electromechanical power steering
The warning light comes on for a few seconds when the ignition is
switched on.
Fig. 20 Vehicle data
sticker
s24s.book Page 33 Thursday, November 24, 2005 12:27 PM
Page 36
Instruments and Indicator/Warning Lights34
If the warning light after switching on the ignition or when driving lights up
continuously, a fault exists in the electromechanical power steering.
• If the yellow warning light lights up, this indicates a partial failure of the
power steering and the steering forces can be greater.
• If the red warning light lights up, this indicates a complete failure of the
power steering and the steering assist has failed (significantly higher
steering forces).
If the red warning light lights up, three peeps sound as an additional
warning signal.
Further information ⇒ page 219, “Electromechanical power steering”.
WARNING
Contact your specialist garage if the power steering is defective.
Note
• If the yellow warning light goes out after starting the engine again
and a short drive, it is not necessary to visit a specialist garage.
• If the battery has been disconnected and reconnected, the yellow
warning light comes on after switching on the ignition. The warning light
must go out after driving a short distance.
Control system for exhaust gases
The warning light comes on after the ignition has been switched on.
If the warning light does not go out after starting the engine or it lights up
or flashes when driving, a fault exists in an exhaust relevant component.
The engine management system selects an emergency programme
which enables you to drive to the nearest specialist garage by adopting a
gentle style of driving.
The following text will be displayed in the information display*:
Emissions workshop!
EPC fault light (petrol engine)
The (Electronic Power Control) warning light comes on for a few
seconds when the ignition is switched on.
If the warning light does not go out or lights up after starting the engine,
a fault exists in the engine control. The engine management system
selects an emergency programme which enables you to drive to the
nearest specialist garage by adopting a gentle style of driving.
The following text will be displayed in the information display*:
Engine fault Workshop! (Engine fault workshop!)
Glow plug system (diesel engine)
The indicator light lights up for a cold engine when switching on the
igntion (pre-heat position) 2 ⇒ page 139. Start the engine just as soon as
the indicator light goes out.
The glow plug indicator light will come on for about 1 second if the engine
is at a normal operating temperature or if the outside temperature is
above +5°C. This means that you can start the engine right away.
There is a fault in the glow plug system if the indicator light does not
come on at all or lights up continuously. Contact a specialist garage as
soon as possible to obtain assistance.
s24s.book Page 34 Thursday, November 24, 2005 12:27 PM
Page 37
Instruments and Indicator/Warning Lights 35
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
If the warning light begins to flash while driving, a fault exists in the
engine control. The engine management system selects an emergency
programme which enables you to drive to the nearest specialist garage by
adopting a gentle style of driving.
The following text will be displayed in the information display*:
Engine fault Workshop! (Engine fault workshop!)
Airbag system
Monitoring the airbag system
The warning light comes on for a few seconds when the ignition is
switched on.
There is a fault in the system if the warning light does not go out or comes
on or flashes while driving ⇒ . This also applies if the warning light does
not come on when the ignition is switched on.
The following text will be displayed in the information display*:
Airbag fault!
The functionality of the airbag system is also monitored electronically,
when one airbag has been switched off
Front, side or head airbags which have been switched off using the
vehicle system tester:
• The warning light lights up for 4 seconds after switching on the igni-
tion and then flashes again for 12 seconds afterwards in 2 second intervals.
The following text will be displayed in the information display*:
Airbag belt tensioner deactivated!
Front passenger airbags switched off using the switch for front
passenger airbags* in stowage compartment on the front passenger
side:
• The warning light comes on for 4 seconds after the ignition has
been switched on.
• Switching off airbags is indicated in the middle of the dash panel by the
lighting up of the indicator light (airbag switched off)
⇒ page 200.
WARNING
Have the airbag system checked immediately by a specialist
garage if a fault exists. Otherwise, there is a risk of the airbag not
being activated in the event of an accident.
Note
Further information about switching off airbags ⇒ page 199.
Coolant temperature/coolant level
The warning light comes on for a few seconds 2) when the ignition is
switched on.
The coolant temperature is too high or the coolant level too low if the
warning light does not go out or flashes while driving.
3 peeps sound as an additional warning signal.
2)
The warning light on vehicles fitted with information display does not come on
after switching the ignition on, but only if the coolant temperature is too high or the
coolant level is too low.
s24s.book Page 35 Thursday, November 24, 2005 12:27 PM
Page 38
Instruments and Indicator/Warning Lights36
In this case stop and switch the engine off and check the coolant level;
top up the coolant as necessary.
Do not continue your journey if for some reason it is not possible under
the conditions prevailing to top up with coolant. Keep the engine
switched off and obtain professional assistance from a specialist garage,
otherwise it could lead to severe engine damages.
If the coolant is within the specified range, the increased temperature may
be caused by an operating problem at the coolant fan. Check the fuse for
the coolant fan, replace it if necessary ⇒ page 290, “Fuse assignment in
engine compartment - version 1” or ⇒ page 291, “Fuse assignment in
engine compartment - version 2”.
Do not continue driving if the warning light does not go off although the
fluid is at the correct level and also the fuse of the fan is in proper order.
Contact a specialist garage to obtain assistance.
Please also refer to the additional instructions ⇒ page 253, “Cooling
system”.
The following text will be displayed in the information display*:
STOP Check coolant! Owner's manual (STOP! Check coolant!
Owner's manual)
WARNING
• If you must stop for technical reasons, then park the vehicle at
a safe distance from the traffic and switch off the engine and switch
on the hazard warning light system ⇒ page 68.
• Take care when opening the coolant expansion bottle. If the
engine is hot, the cooling system is pressurized - risk of scalding!
It is best to allow the engine to cool down before removing the cap.
• Do not touch the coolant fan The coolant fan may switch on
automatically even if the ignition is off.
Thickness of the brake pads*
The warning light comes on for a few seconds 3) when the ignition is
switched on.
If the warning light comes on, contact a specialist garage immediately
and have the brake pads on all of the wheels inspected.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
Check brake pads!
Windshield washer fluid level*
The warning light comes on when the ignition is switched on if there is
insufficient fluid in the windshield washer system. Top up with liquid
⇒ page 262.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
Top up wash fluid!
Fuel reserve
The warning light comes on, if the fuel level is still below 8 litres.
A peep sounds as an additional warning signal.
3)
The warning light on vehicles fitted with information display does not come on
after switching the ignition on, but only if a fault exists.
s24s.book Page 36 Thursday, November 24, 2005 12:27 PM
Page 39
Instruments and Indicator/Warning Lights 37
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The following text will be displayed in the information display*:
Please refuel!
Note
The Text in the information display* goes out only after refuelling and
driving a short distance.
Engine oil pressure
The warning light comes on for a few seconds 4) when the ignition is
switched on.
Stop the vehicle and switch the engine off if the warning light does not
go off after the engine has started or flashes while driving. Check the oil
level and top up with oil as necessary ⇒ page 251.
3 peeps sound as an additional warning signal.
Do not continue your journey if for some reason it is not possible under
the conditions prevailing to top up with oil. Keep the engine switched off
and obtain professional assistance from a specialist garage, otherwise it
could lead to severe engine damages.
Do not drive any further if the warning light flashes even if the oil is at
the correct level. Do not run the engine not at idling speed either. Contact
the nearest specialist garage to obtain professional assistance.
The following text will be displayed in the information display*:
STOP Oil Pressure Engine off! Owner's manual
WARNING
• If you must stop for technical reasons, then park the vehicle at
a safe distance from the traffic and switch off the engine and switch
on the hazard warning light system ⇒ page 68.
• The red oil pressure light is not an oil level indicator! One
should therefore check the oil level at regular intervals, preferably
after every refueling stop.
Bonnet
The warning light comes on if the bonnet is unlocked.
The warning light comes on even when the ignition is switched off. The
warning light goes out about 15 seconds after locking the vehicle.
Open door*
The warning light comes on if one or several doors are opened or if the
boot lid is opened.
The warning light on vehicles fitted with information display comes on
when switching the ignition off. The warning light goes out about 15
seconds after locking the vehicle.
The warning light on vehicles fitted with information display goes out after
switching the ignition off.
4)
The warning light on vehicles fitted with information display does not come on
after switching the ignition on, but only if a fault exists or the engine oil level is too
low.
s24s.book Page 37 Thursday, November 24, 2005 12:27 PM
Page 40
Instruments and Indicator/Warning Lights38
Engine oil level*
Warning light lights up
If the warning light lights up, the quantity of oil in the engine is probably
too low. Check as soon as possible the oil level or top up ⇒ page 251 with
engine oil.
A peep sounds as an additional warning signal.
The following text will be displayed in the information display*:
Check oil level!
The warning light will go out if the bonnet is left open for more than 30
seconds. If no engine oil has been replenished, the warning light will come
on again after driving about 100 km.
Warning light flashes
A fault on the engine oil level sensor is indicated additionally by an audible
signal and the warning light coming on several times after the ignition has
been switched on.
In this case have the engine inspected without delay by a specialist
garage.
The following text will be displayed in the information display*:
Oil sensor workshop!
Tyre inflation pressure*
The warning light lights up, if there is a substantial drop in inflation
pressure in one of the tyres. Reduce the speed and check or correct as
soon as possible the inflation pressure in the tyres ⇒ page 264.
A peep sounds as an additional warning signal.
If the warning light flashes, there is a system fault. Visit the nearest
specialist garage and have the fault rectified.
Further information about tyre pressure-control system ⇒ page 220.
WARNING
• When the warning light lights up, immediately reduce the
speed and avoid sudden steering and brake manoeuvres. Please
stop the vehicle without delay at the nearest possible stop and
inspect the tyres and their inflation pressures.
• Under certain circumstances (e.g. sporty style of driving, wintry
or unpaved roads) the warning light can be delayed or does not
light up at all.
Note
If the battery has been disconnected, the warning light comes on after
switching on the ignition. The warning light must go out after driving a
short distance.
Selector lever lock*
If the warning light lights up, operate the brake pedal. This is necessary, in order to be able to move the selector lever out of the position P or
N.
Antilock brake system (ABS)
The warning light shows the functionality of the ABS.
s24s.book Page 38 Thursday, November 24, 2005 12:27 PM
Page 41
Instruments and Indicator/Warning Lights 39
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The warning light comes on for a few seconds after the ignition has been
switched on or when starting the engine. The warning light goes out after
an automatic check sequence has been completed.
A fault in the ABS
If the ABS warning light does not go out within a few seconds after
switching on the ignition or does not light up at all or lights up while driving,
the system is not functioning properly and the vehicle will be braked
without the aid of ABS. The vehicle will only be braked by the normal brake
system. Visit a specialist garage as quickly as possible and adjust your
style of driving in the meantime since you will not know how great the
damage is.
Three additional warning tones will sound if there is a major fault in the
ABS.
Further information about ABS ⇒ page 218, “Antilock brake system
(ABS)”.
A fault in the entire brake system
If the ABS warning light comes on together with the brake system
warning light (handbrake must be released), there is a fault not only in
the ABS but also in another part of the brake system ⇒ .
WARNING
• If the brake system warning light comes on together with the
ABS warning light stop the vehicle immediately and check the
brake fluid level in the reservoir ⇒ page 256, “Brake fluid”. If the
fluid level has dropped below the MIN marking, do not drive any
further - risk of accident! Contact a Škoda dealer to obtain professional assistance.
• Pay attentio n to the following instructions ⇒ page 248, “Working
in the engine compartment” before checking the brake fluid level
and opening the bonnet.
• If the brake fluid is at the correct level, the ABS control function
has failed. The rear wheels may then block very rapidly when
braking. In certain circumstances, this can result in the rear end of
the car breaking away - risk of skidding! Drive carefully to the
nearest specilaist garage and have the fault rectified.
Traction control system (TCS)
The warning light comes on for a few seconds when the ignition is
switched on.
The warning light comes on when driving when a control cycle is activated.
The warning light will come on and remains on if the TCS is switched off
or if there is a fault in the system.
The fact that the TCS system operates together with the ABS means that
the TCS warning light will also come on if the ABS system is not operating
properly.
If the warning light comes on immediately after starting the engine, the
TCS system can be switched off for technical reasons. In this case, the
TCS system can be switched on again by switching the ignition on and off.
If the warning light goes out, the TCS system is fully functional again.
Further information about the TCS ⇒ page 215, “Traction control system
(TCS)”.
WARNING (continued)
s24s.book Page 39 Thursday, November 24, 2005 12:27 PM
Page 42
Instruments and Indicator/Warning Lights40
Note
If the battery has been disconnected and reconnected, the warning light
comes on after switching on the ignition. The warning light must go out
after driving a short distance.
Electronic Stability Programme (ESP)*
The warning light comes on for a few seconds when the ignition is
switched on.
Components of the ESP system also include the Traction Control System
(TCS), Electronic Differential Lock (EDL), and the Antilock Brake System
(ABS).
The warning light comes on when driving when a control cycle is activated.
The warning light will come on and remains on if the ESP is switched off
or if there is a fault in the system.
The fact that the ESP system operates together with the ABS means that
the ESP warning light will also come on if the ABS system is not operating
properly.
If the warning light comes on immediately after starting the engine, the
ESP system can be switched off for technical reasons. In this case, the
ESP system can be switched on again by switching the ignition on and off.
If the warning light goes out, the ESP system is fully functional again.
Further information on the ESP ⇒ page 213, “Electronic stability
programme (ESP)*”.
Electronic Differential Lock (EDL)*
The EDL is a part of the ESP. A fault in the EDL is indicated by the ESP
warning light in the instrument cluster. Have the vehicle inspected without
delay by a Škoda dealer. Further information on the EDL ⇒ page 214,
“Electronic Differential Lock (EDL)*”.
Note
If the battery has been disconnected and reconnected, the warning light
comes on after switching on the ignition. The warning light must go out
after driving a short distance.
Dynamo
The warning light comes on after the ignition has been switched on. It
should go out after the engine has started.
If the warning light does not go out after the engine has started, or comes
on when driving, drive to the nearest specialist garage. The vehicle battery
will be discharged in this case so switch off all non-essential electrical
components.
Caution
If the warning light comes on when driving and in addition the warning
light (cooling system fault) also comes on in display, you must then
stop the car immediately and switch the engine off - risk of engine
damage!
Brake system
The warning light flashes or comes on if the brake fluid level is too low,
if there is a fault in the ABS or if the handbrake is applied.
s24s.book Page 40 Thursday, November 24, 2005 12:27 PM
Page 43
Instruments and Indicator/Warning Lights 41
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
If the warning light flashes (handbrake is not applied), stop and check
the brake fluid level ⇒ .
The following text will be displayed in the information display*:
STOP Brake fluid Owner's manual
If there is a fault in the ABS which also influences the function of the
normal brake system (e.g. distribution of brake pressure), the ABS
warning light comes on together with the brake system warning light
. Be aware that not only the ABS but also another part of th brake
system is defective ⇒ .
3 peeps sound as an additional warning signal.
One should get used to high pedal forces, long braking distances and long
free play of the brake pedal when driving to the next specialist garage.
For further information on the brake system ⇒ page 216, “Brakes”.
Handbrake applied
The warning light also comes on if the handbrake is applied. An audible
warning is also given if you drive the vehicle for at least 3 seconds at a
speed of more than 6 km/h.
The following text will be displayed in the information display*:
Handbrake on!
WARNING
• Pay attentio n to the following instructions ⇒ page 248, “Working
in the engine compartment” before checking the brake fluid level
and opening the bonnet.
• If the brake system warning light does not go out a few
seconds after switching on the ignition or comes on when driving,
stop immediately and check the brake fluid in the reservoir
⇒ page 256, “Brake fluid”. If the fluid level has dropped below the
MIN marking, do not drive any further - risk of accident! Contact a
Škoda dealer to obtain professional assistance.
Seat belt warning light*
The warning light comes on after the ignition is switched on as a
reminder to fasten the seat belt. The warning light only goes out if the
driver has fastened his seat belt.
If you do not fasten the seat belt, a long warning signal sounds for 6
seconds.
If you do not fasten the seat belt, a warning signal sounds continuously at
a speed of more than 10 km/h.
The following text will be displayed in the information display*:
Please fasten seatbelt!
For further information on the seat belts ⇒ page 183, “Seat belts”.
WARNING (continued)
s24s.book Page 41 Thursday, November 24, 2005 12:27 PM
Page 44
Unlocking and locking42
Unlocking and locking
Keys
The vehicle is supplied with two keys. Depending on the equipment fitted,
your vehicle can be equipped with keys without remote control ⇒ fig. 21;
with keys with light* ⇒ page 43, fig. 23 or with keys with radio remote
control* ⇒ fig. 22.
Key ring
The key ring ⇒ fig. 21 only has the key number on it which is essential for
producing other keys. This number can be used to order replacement
keys from Škoda dealers.
The key ring with the number should be separately and securely kept in
safe keeping since keys can only be replaced if they are lost or damaged
by giving this number. You should also therefore give this key ring to the
purchaser when selling the vehicle.
WARNING
• Always withdraw the key whenever you leave the vehicle - even
if it is only for a short time. This is particularly important if children
are left in the vehicle. The children might otherwise start the engine
or operate electrical equipment (e.g. power windows) - risk of
injury!
• Do not withdraw the ignition key from the ignition lock until the
vehicle has come to a stop. The steering lock might otherwise
engage unintentionally - risk of accident!
Caution
• Each key contains electronic components; therefore protect them
against moisture and severe shocks.
Fig. 21 Set of keys
without remote control
Fig. 22 Radiooperated
key
s24s.book Page 42 Thursday, November 24, 2005 12:27 PM
Page 45
Unlocking and locking 43
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
• Keep the groove of the keys absolutely clean as impurities (textile
fibres, dust etc.) have a negative effect on proper operation of the keys
and the ignition lock.
Note
Please approach a Škoda dealer if you lose a key since he can obtain a
new one for you.
Key with light*
Switching on the light
– Press the button in the middle in the direction of arrow .
Replacing battery or bulb
– Insert a coin into the slot (arrow ) and press off the upper
part through a rotary movement of the coin.
– Replace the battery or bulb.
– Place the upper and lower part above each other and press
the parts together.
You can obtain replacement batteries and replacement bulbs at a
specialist garage.
For the sake of the environment
Dispose of an old battery in accordance with environmental regulations.
Note
The replacement battery must have the same specification as the original
battery.
Fig. 23 Key with light
A
1
A
2
s24s.book Page 43 Thursday, November 24, 2005 12:27 PM
Page 46
Unlocking and locking44
Changing the battery of the radio remote
control
Each radio-operated key contains a battery which is housed in
the cover of the transmitter housing ⇒ fig. 24. We recommend
that you have the batteries of the key replaced by a Škoda dealer.
You should, however, proceed as follows if you wish to replace
the battery yourself:
– Fold open the key.
– Use a thin screwdriver to carefully lever off the front part of the
key ⇒ fig. 24 from the transmitter housing .
– Take off the cover of the transmitter housing ⇒ fig. 25 in direc-
tion of arrow.
– Take the used battery out of the housing cover.
– Insert the new battery. Ensure that the “+” symbol on the
battery is facing downwards. The correct polarity is also
shown on the cover of the transmitter housing.
– Insert cover with battery in place at the rear of the transmitter
housing and press both parts together.
– Insert the transmitter housing into the front part of the key so
that the two parts lock into each other.
For the sake of the environment
Dispose of an old battery in accordance with environmental regulations.
Note
• The replacement battery must have the same specification as the orig-
inal battery.
Fig. 24 Disconnect key
with radio remote
control
Fig. 25 Cover of the
transmitter housing
A
B
AAA
B
s24s.book Page 44 Thursday, November 24, 2005 12:27 PM
Page 47
Unlocking and locking 45
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
• If it is still not be possible to unlock or lock the vehicle with the remote
control even after replacing the battery this means that the system has to
be synchronised ⇒ page 53.
Electronic immobiliser
The electronic immobiliser prevents the vehicle being
operated by an unauthorised person.
An electronic chip is integrated in the head of the key. The immobiliser is
deactivated with the aid of this chip when the key is inserted in the ignition
lock. The electronic immobiliser is automatically activated when you withdraw the ignition key from the lock.
Note
It is only possible to start the engine of your car with a Genuine Škoda key
with the matching code ⇒ page 32.
Child safety locks
The child safety lock prevents the rear door from being
opened from the inside.
The rear doors are equipped with a child safety lock. You can
switch the child safety lock on and off using the vehicle key.
Switching child safety lock on
– Use the vehicle key to turn the slit in the rear door to the left in
the direction of the arrow ⇒ fig. 26.
Switching child safety lock off
– Use the vehicle key to turn the slit to the right against the direc-
tion of the arrow.
Fig. 26 Child safety
locks on the rear doors
s24s.book Page 45 Thursday, November 24, 2005 12:27 PM
Page 48
Unlocking and locking46
So long as the child safety lock is switched on it is not possible to open the
door from the inside with the door opening lever. In this case the door can
be opened only from the outside.
Central locking system
Description
Unlocking or locking the vehicle causes all the doors and the fuel filler
flap* to be unlocked or locked at the same time by the central locking
system. The boot lid is unlocked when opening. It can be opened by
pressing the hand grip above the licence plate ⇒ page 50, fig. 30.
Operation of the central locking system is possible:
• from the outside using the vehicle key ⇒ page 47,
• using the buttons for the central locking system ⇒ page 48,
• by using the remote control ⇒ page 52.
Indicator light in the driver's door on vehicles without anti-theft
alarm system
After the car is locked, the indicator light flashes after 2 seconds.
After the car is locked with the deactivated safe securing system, the indicator light flashes only after 30 seconds.
Indicator light in the driver's door on vehicles with anti-theft alarm
system
After locking the vehicle the indicator light flashes for 2 seconds fast, then
more slowly.
If the vehicle is locked and the safe securing system ⇒ page 47 is not operating, the indicator light in the driver door flashes for about 2 seconds fast,
goes out and starts to flash slowly after about 30 seconds.
If the indicator light first of all flashes fast for about 2 seconds, afterwards
lights up for about 30 seconds and then flashes slowly, there is a fault in
the system of the central locking or the interior monitor* ⇒ page 55.
Contact a specialist garage to obtain assistance.
Convenience operation of windows
One can open and close the electrically powered windows when unlocking
and locking the vehicle ⇒ page 58, “Convenience operation of windows”.
Opening a single door*
This function allows one to just unlock the driver's door. The other doors
and the fuel filler flap* remain locked and are only unlocked after repetitive
unlocking.
If you wish, you can have your Škoda Dealer activate the function of the
single door opening mode.
Automatic locking*
All the doors and the boot lid are locked automatically once the car
reaches a speed of about 15 km/h.
If the ignition key is withdrawn, the car is then automatically unlocked
again. In addition, it is possible for the driver to unlock the car by pressing
the central locking button or by pulling the door opening lever.
If you wish, your Škoda Dealer can activate the function of the automatic
locking mode.
WARNING
Locking the doors prevents involuntary opening in an exceptional
situation (an accident). Locked doors prevent unwanted entry into
the vehicle from outside, for example at road crossings. Locked
doors do, however, make it more difficult for rescuers to get into
the vehicle in an emergency - danger to life!
s24s.book Page 46 Thursday, November 24, 2005 12:27 PM
Page 49
Unlocking and locking 47
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• In the event of an accident in which the airbags are deployed, the
locked doors are automatically unlocked in order to enable rescuers to
gain access to the vehicle.
• Only the front doors can be unlocked and locked using the key if the
central locking system fails. You can lock or unlock manually the other
doors and the boot lid.
− Emergency locking of the door ⇒ page 49.
− Emergency unlocking of the boot lid ⇒ page 51.
Safe securing
The central locking system is equipped with a safe securing system.
Locking the vehicle from the outside causes the door locks to be automatically blocked. It is not possible to open the doors with the door handle
either from the inside or from the outside. This acts as an effective deterrent for attempts to break into your vehicle.
You can deactivate the safe securing system. This is done by locking the
vehicle with the key or radio-operated key twice within 2 seconds.
If the safe securing system is not operating:
• the indicator light in the driver door flashes for about 2 seconds fast,
goes out and starts to flash slowly after about 30 seconds,
• is the fuel filler flap unlocked.
The safe securing system is again activated the next time the vehicle is
unlocked and locked again.
The doors can be opened from the inside if the vehicle is locked and the
safe securing system is deactivated:
• the door is unlocked by actuating the door-opening lever,
• the door opens upon actuating the door-opening lever again.
WARNING
If the vehicle is locked from the outside and the safe securing
system is activated, there must not be any person and animals in
the vehicle as it is then not possible to open either a door or a
window from the inside. The locked doors make it more difficult for
rescuers to get into the vehicle in an emergency - hazard!
Note
The anti-theft alarm system* is also activated with the deactivated safe
securing system when locking the vehicle. The interior monitor* is
however not activated.
Unlocking the vehicle using the key
Fig. 27 Turning the
key for unlocking and
locking the vehicle
s24s.book Page 47 Thursday, November 24, 2005 12:27 PM
Page 50
Unlocking and locking48
– Turn the key in the lock of the driver's door to the left into the
opening position ⇒ page 47, fig. 27.
– Pull on the door handle and open the door.
• All the doors (only the driver's door on vehicles with anti-theft alarm
system) and the fuel filler flap* are unlocked.
• The boot lid is then unlocked.
• The switched on interior lights come on over the door contact.
• The safe securing system is deactivated.
• The windows are opened provided the key is held in the opening posi-
tion*. On vehicles fitted with anti-theft alarm system the window operation
is only possible 45 seconds after deactivation of the warning system.
• The indicator light in the driver's door stops flashing if the vehicle is not
fitted with an anti-theft alarm system* ⇒ page 54.
Note
If the vehicle is equipped with an anti-theft alarm system*, you must
unlock the vehicle by inserting the key into the driver door you then have
to insert the key into the ignition lock and switch the ignition on within 15
seconds after opening the door. The alarm will be triggered if you do not
switch on the ignition within 15 seconds.
Closing the vehicle with the key
– Turn the key in the lock of the driver door to the right into the
closing position ⇒ page 47, fig. 27.
• The doors, the boot lid and the fuel filler flap* are locked.
• The switched on interior lights will switch off over the door contact.
• The windows and the electric sliding/tilting roof* are closed provided
the key is held in the locking position.
• The safe securing system is activated immediately.
• The indicator light in the driver door begins flashing.
Note
The opened driver door cannot be locked. It must be locked separately
after closing it.
Buttons for central locking
If the vehicle was not locked from outside, you can also unlock
and lock it with the rocker switch on the centre console without
the ignition switched on.
A
A
A
B
Fig. 28 Centre
console: Buttons for
central locking
s24s.book Page 48 Thursday, November 24, 2005 12:27 PM
Page 51
Unlocking and locking 49
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Locking all doors and the boot lid
– Press button ⇒ page 48, fig. 28. The symbol
in the button
comes on.
Unlocking all doors and the boot lid
– Press button ⇒ page 48, fig. 28. The symbol
goes out in
the button.
The following applies if you have locked your vehicle using the button :
• It is not possible to open the doors or the boot lid from the outside
(safety feature, e.g. when stopping at traffic lights etc.).
• You can unlock the doors individually from the inside and open them
by pulling the door opening lever.
• If the driver door is opened, it cannot be locked, in order to avoid inad-
vertently being locked out of the vehicle You then have to lock a door
separately after closing it.
• In the event of an accident in which the airbags are deployed, the
locked doors are automatically unlocked from the inside in order to enable
rescuers to gain access to the vehicle.
If the ignition is switched off, you can conveniently close or open the
windows by pressing and holding the button or ⇒ page 58.
WARNING
The central locking system also operates if the ignition is switched
off. All the doors and the boot lid are locked. Children should never
be left unattended in the vehicle since it is difficult to provide
assistance from the outside when the doors are locked. Locked
doors make it difficult for rescuers to get into the vehicle in an
emergency - hazard!
Note
The door opening lever and the buttons for the central locking system do
not operate if the safe securing system is activated.
Emergency locking of the doors
An emergency locking mechanism is located on the rear side of
the doors which have no locking cylinder; it is only visible after
opening the door.
Locking
– Remove the panel ⇒ fig. 29.
– Insert the key into the opening under the panel and press the
stopping lever as far as the stop toward the inside.
A1A
2
A
1
A1A
2
Fig. 29 Rear door:
Emergency locking of
the door
A
A
A
B
s24s.book Page 49 Thursday, November 24, 2005 12:27 PM
Page 52
Unlocking and locking50
– Re-insert the panel.
After closing the door, you can no longer open it from outside. If the child
safety lock is not switched on, it is possible to open the door from the
inside by pulling twice on the door handle. If the child safety lock is
switched on, it is necesary to also open the door from outside besides
pulling twice on the inner door handle.
Boot lid
Open the boot lid by pressing the hand grip above the licence
plate after unlocking the vehicle using the key or the radio remote
control.
Opening the boot lid
– Press on the handle ⇒ fig. 30 and at the same time raise the
boot lid.
Closing the boot lid
– Pull the boot lid down and close it with a slight swing ⇒ .
A handle which makes the closing easier is located on the inner paneling
of the boot lid.
WARNING
• Ensure that the lock is properly engaged after closing the boot
lid. Otherwise, the boot lid might open suddenly when driving even
if the boot lid lock is closed - risk of accident!
• Never drive with the boot lid slightly ajar or even fully opened
otherwise exhaust gases may get into the interior of the vehicle risk of poisoning!
• Do not press on the rear window when closing the boot lid, it
could crack - risk of injury!
Note
• After closing the boot lid, it is automatically locked within
2 seconds and the anti-theft alarm system* is activated. This applies
only if the vehicle was locked before closing the boot lid.
• The function of the hand grip above the licence plate is deactivated
when starting off or at a speed of more than 5 km/hour for vehicles with
central locking. The function of the hand grip is activated again when the
vehicle has stopped and a door is opened.
Fig. 30 Handle of boot
lid
s24s.book Page 50 Thursday, November 24, 2005 12:27 PM
Page 53
Unlocking and locking 51
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Emergency unlocking of the boot lid (Octavia)
If there is a fault in the central locking, you can open the boot lid
as follows:
– Fold the rear seats forwards ⇒ page 89.
– Take out the warning triangle* ⇒ fig. 31.
– Press the operating lever in the direction of arrow in order to
unlock the boot lid. The operating lever is located under the
panel .
– Open the boot lid/luggage compartment door from outside.
Emergency unlocking of the boot lid (Estate car)
If there is a fault in the central locking, you can open the boot lid
as follows:
– Fold the rear seats forwards ⇒ page 89.
– Open up the cover of the lock upwards ⇒ fig. 32.
– Move the operating lever with the aid of a narrow object
e.g. screwdriver up to the stop in the direction of arrow; the
boot lid is then unlocked.
– Open the boot lid/luggage compartment door from outside.
Fig. 31 Emergency
unlocking of the boot
lid
A
A
A
B
Fig. 32 Emergency
unlocking of the boot
lid
A
A
s24s.book Page 51 Thursday, November 24, 2005 12:27 PM
Page 54
Unlocking and locking52
Remote control*
Description
You can use the remote control:
• to unlock and lock the car,
• unlocking boot lid,
• Opening and closing window.
The transmitter with the battery is housed in the handle of the master key.
The receiver is located in the interior of the car. The operating range of the
remote control is 10 metres but this range can be reduced if the batteries
are waek.
The master key has a fold-open key bit which can be used for unlocking
and locking the car manually and also for starting the engine.
If a lost key is replaced or if the receiver unit has been repaired or a new
unit installed, it is then necessary for a Škoda Dealer to initialise the
system. Only after this is it possible to again use the remote control.
Note
• The remote control is automatically deactivated when the ignition is
switched on.
• The operation of the remote control may temporarily be affected by
interference from transmitters close to the car and which operate in the
same frequency range (e.g. mobile phone, TV transmitter).
• The battery must be replaced, ideally by the Škoda dealer, if the
central locking or anti-theft alarm system does react to the remote control
at less than 3 metres away.
Unlocking and locking car
Unlocking the vehicle
– Press button for about 1 second.
Locking the vehicle
– Press button for about 1 second.
Deactivating safe securing system
– Press button twice in 2 seconds. Further information
⇒ page 47.
Boot lid remote release
– Press button for about 2 seconds ⇒ fig. 33. Further infor-
mation ⇒ page 50.
Fig. 33 Radio-operated key
A1A3A
3
A
2
s24s.book Page 52 Thursday, November 24, 2005 12:27 PM
Page 55
Unlocking and locking 53
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Folding out of the key
– Press button .
Folding up of the key
– Press button and collapse the key bit in the housing.
The turn signal lights flash twice as confirmation that the vehicle has been
unlocked. The vehicle will lock again automatically if you unlock the
vehicle using button but do not open a door or the boot lid within the
next 30 seconds. This function is intended to prevent the car being
unlocked unintentionally.
In addition, when the car is unlocked, the power seats and exterior
mirrors* move into the position assigned to this key. The stored setting of
driver seat and exterior mirrors is retrieved.
The turn signal lights flash once to confirm that the vehicle has been
correctly locked. If the turn signal lights do not flash, check the doors,
bonnet and boot lid again to ensure that they are closed. If the doors, the
bonnet or the boot lid remain open when the anti-theft alarm system is
activated, the turn signal lights do not flash until after they have been
closed.
When the vehicle is unlocked or locked, the interior lights in the door
contact are automatically switched on or off.
WARNING
If the vehicle is locked from the outside and the safe securing
system is activated, there must not be any person in the vehicle as
it is then not possible to open either a door or a window from the
inside. The locked doors make it more difficult for rescuers to get
into the vehicle in an emergency - hazard!
Note
• Operate the radio remote control only when the doors and boot lid are
closed and you have visual contact with the vehicle.
• Once in the car, you must not press the lock button of the radio
remote control before inserting the key into the ignition lock in order to
avoid the car being inadvertently locked and, in addition, the anti-theft
alarm system* being switched on. Should this happen, press the unlock
button of the radio remote control.
Synchonisation of the remote control
If the vehicle cannot be unlocked by actuating the remote control system
then it is possible that the code in the key and the control unit in the vehicle
are no longer synchronised. This can occur when the buttons on the radiooperated key are actuated a number of times outside of the operative
range of the equipment or the battery on the remote control was replaced.
This means it is necessary to synchronise the code as follows:
• Press any button on the remote control.
• Pressing of the button means that the door will unlock with the key
within 1 minute.
A4A
4
A
1
s24s.book Page 53 Thursday, November 24, 2005 12:27 PM
Page 56
Unlocking and locking54
Anti-theft alarm system*
Description
The anti-theft alarm system increases the level of protection against
people seeking to break into the vehicle. The system triggers audible and
visual warning signals if an attempt is made to break into the vehicle.
How is the alarm system activated?
The anti-theft alarm system is activated automatically when the vehicle is
locked with the key on the closed driver's door or by using the radio
remote control. It is activated 30 seconds after closing the door.
How is the alarm system deactivated?
The anti-theft alarm system is deactivated if the vehicle is unlocked by
only using the radio remote control. The vehicle is automatically locked
again if the vehicle is not opened within 30 seconds after reactivating the
anti-theft alarm system.
Once you unlock the vehicle by inserting the key into the driver door you
then have to insert the key into the ignition lock and switch the ignition on
within 15 seconds after opening the door in order to deactivate the antitheft alarm system. The alarm will be triggered if you do not switch on
the ignition within 15 seconds.
When is the alarm triggered?
The following security areas of the locked vehicle are monitored:
• Bonnet,
• Boot lid,
• Doors,
• Ignition lock,
• Angle of the vehicle* ⇒ page 55,
• Vehicle interior* ⇒ page 55,
• A drop in voltage of the on-board power supply.
An alarm is immediately triggered if either of the two battery terminals is
disconnected while the anti-theft alarm system is activated.
How is the alarm switched off?
You switch the alarm off if you unlock the car with the radio remote control
in the key or if you switch the ignition on.
Note
• The working life of the alarm siren is 6 years. More detailed information
is available from your Škoda dealer.
• Before leaving the car, check that all the doors, windows and the elec-
tric sliding/tilting roof* are properly closed in order to ensure that the antitheft alarm system is fully operational.
• Coding of the radio remote control and the receptor part precludes the
use of the radio remote control from other vehicles.
s24s.book Page 54 Thursday, November 24, 2005 12:27 PM
Page 57
Unlocking and locking 55
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Interior monitor*
The interior monitor detects movements inside the car and
then triggers the alarm.
You must switch the interior monitor off if, for example, a child or
an animal inside the car might trigger the alarm.
Deactivation of interior monitor
– Switch off the ignition.
– Open the driver door.
– Press the button
at the centre colum on the driver side
⇒ fig. 34, the symbol
lights up in the button.
– Lock the vehicle within 30 seconds.
The interior monitor is switched on again automatically the next time the
car is locked.
Note
• You can also switch off the interior monitor, by deactivating the safe
securing system ⇒ page 47.
• The version of the button can differ depending on the equipment
installed in the vehicle.
Towing protection monitoring*
The towing protection monitoring should be switched off, if the
vehicle is transported (e.g. by rail or by ship) or should be towed.
Switching off the towing protection monitoring
– Switch off the ignition.
Fig. 34 Interior
monitor pushbutton
Fig. 35 Button for the
towing protection
monitoring
s24s.book Page 55 Thursday, November 24, 2005 12:27 PM
Page 58
Unlocking and locking56
– Open the driver door.
– Press the button
at the centre colum on the driver side
⇒ page 55, fig. 35, the symbol
lights up in the button.
– Lock the vehicle within 30 seconds.
The interior monitor is switched on again automatically the next time the
car is locked.
Power windows*
Buttons on the driver's door
The power windows operate only when ignition is switched on.
Opening a window
– A window is opened by pressing lightly on the respective
button in the door. The process stops when one releases the
button.
– Additionally you can open the window automatically (fully
opened) by pressing the button up to the stop. Renewed
pressing of the button causes the window to stop immediately.
Closing a window
– A window is closed through pulling lightly on the respective
button in the door. The closing process stops when one
releases the button.
– Additionally you can close the window automatically (fully
closed) by pulling the button up to the stop. Renewed pulling
of the button causes the window to stop immediately.
The button for the individual windows is located in the armrest of the
driver's door ⇒ fig. 36, front passenger door and in the rear doors*
⇒ page 57, fig. 37.
Buttons for the power window in the armrest of the driver's door
Button for the power window in the driver's door
Button for the power window in the front passenger's door
Button for the power window in the rear door on the right*
Button for the power window in the rear door on the left*
Safety pushbutton*
Fig. 36 Buttons on the
driver's door
A
A
A
B
ACA
D
A
S
s24s.book Page 56 Thursday, November 24, 2005 12:27 PM
Page 59
Unlocking and locking 57
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Safety pushbutton*
You can deactivate the buttons for the rear doors using the safety button
⇒ page 56, fig. 36. The buttons for power windows at rear doors are
activated again by pressing the safety pushbutton again.
If the buttons for the rear doors are deactivated, the indicator light in
the safety switch lights up.
WARNING
• If you lock the vehicle from the outside, do not leave any person
in the vehicle since it is no longer possible to open the windows
from the inside in an emergency.
• The system is fitted with a force limiter ⇒ page 58. The closing
process will be stop if an obstruction is detected and the window
will open again. You should nevertheless take particular care when
closing the windows! A person may otherwise suffer severe injuries as a result of getting an arm, for example, jammed in the
window!
• It is recommended to deactivate the electrically operated power
windows in the rear doors (safety pushbutt on) ⇒ page 56, fig. 36
when children are being transported on the rear seats.
Note
• After switching the ignition off, it is still possible to open or close the
windows for a further 10 minutes. The automatic window closing will not
operate during this time. The power windows are switched off completely
once you open the driver or front passenger door.
• When driving, use the existing heating, air conditioning and ventilation
system for ventilating the interior of the vehicle. If the windows are
opened, dust and other dirt can get into the vehicle. The wind noise is
more at certain speeds.
Switches in front passenger door and in rear doors
A switch for the relevant window is provided in these doors.
Opening a window
– Lightly press the appropriate switch down and hold it until the
window has moved into the desired position.
– Additionally you can open the window automatically (fully
opened) by pressing the switch down up to the stop.
Renewed pressing of the button causes the window to stop
immediately.
Closing a window
– Lightly press the appropriate switch up and hold it until the
window has moved into the desired position.
A
S
ASA
S
A
S
Fig. 37 Position of
switch in front
passenger door
s24s.book Page 57 Thursday, November 24, 2005 12:27 PM
Page 60
Unlocking and locking58
– Additionally you can close the window automatically (fully
closed) by pressing the switch up up to the stop. Renewed
pressing of the button causes the window to stop immediately.
WARNING
The system is fitted with a force limiter ⇒ page 58. The closing
process will be stop if an obstruction is detected and the window
will open again. You should then take particular care when closing
the windows! A person may otherwise suffer severe injuries as a
result of getting an arm, for example, jammed in the window!
Note
After switching the ignition off, it is still possible to open or close the
windows for a further 10 minutes. The automatic closing and opening
functions will not operate during this time. The power windows are
switched off completely once you open the driver or front passenger
door.
Force limiter of the power windows
The electrically operated power windows are fitted with a force limiter. It
reduces the risk of bruises or injuries when closing the windows.
If there is an obstacle, the closing process is stopped and the window
goes down by several centimeters.
You must try to close the window again within 10 seconds, even if the
obstacle was not yet removed, the closing process is stopped. During this
time it is not possible to automatically close the window. The force limiter
is still switched on.
The force limiter is only switched off, if you attempt to close the window
within the next 10 seconds - the window closes now with full strength!
If you wait longer than 10 seconds, the force limiter is switched on again.
WARNING
You should take particular care when closing the windows! A
person may otherwise suffer severe injuries as a result of getting
an arm, for example, jammed in the window!
Convenience operation of windows
You can open and close the electrically powered windows as
follows when unlocking and locking the vehicle (just closing of the
sliding roof).
Opening a window
– Turn the key in the lock of the driver door into the opening
position or press the opening button of the radio remote
control until all the windows are open.
Closing a window
– Turn the key in the lock of the driver door into the closing posi-
tion or press the closing button of the radio remote control until
all the windows are closed.
You can interrupt the opening or closing operation of the windows immediately by releasing the key or the closing button.
s24s.book Page 58 Thursday, November 24, 2005 12:27 PM
Page 61
Unlocking and locking 59
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
WARNING
The system is fitted with a force limiter ⇒ page 58. The closing
process will be stop if an obstruction is detected and the window
will open again. You should then take particular care when closing
the windows! A person may otherwise suffer severe injuries as a
result of getting an arm, for example, jammed in the window!
Note
• On vehicles fitted with anti-theft alarm system the convenience
window opening is possible by means of the key in the lock only 45
seconds after deactivating the warning system or after activating the antitheft alarm system.
Operational problems
Automatic closing or opening does not operate
If the battery of the car has been disconnected and then reconnected, the
automatic closing and opening function does not operate. The system
must be activated. Proceed as follows in order to re-establish the function:
• Turn the key in the lock of the driver door into the closing position and
hold it there until all of the windows are closed.
• Release the key.
• Insert the key again and turn it to the closing position for about 3
seconds.
Operation in winter
Ice accumulating on the surface of the windows during the winter may
result in a greater resistance when closing the windows and the window
may stop and move back several centimetres
Proceed as follows to close the window fully:
• Turn the key in the lock of the driver door into the closing position and
hold it there until all of the windows are closed.
• Repeat this operatiive cycle when the window stops.
WARNING
The system is fitted with a force limiter ⇒ page 58. The closing
process will be stop if an obstruction is detected and the window
will open again. You should then take particular care when closing
the windows! A person may otherwise suffer severe injuries as a
result of getting an arm, for example, jammed in the window!
Electric sliding/tilting roof*
Description
Fig. 38 Control dial for
the power sliding/tilting
roof
s24s.book Page 59 Thursday, November 24, 2005 12:27 PM
Page 62
Unlocking and locking60
The sliding/tilting roof is operated by means of the control dial ⇒ page 59,
fig. 38 and only functions when the ignition is switched on. The control dial
has a number of fixed positions.
After switching the ignition off, it is still possible to open or close the
sliding/tilting roof for a further 10 minutes. It is no longer possible to
operate the sliding/tilting roof after opening or closing one of the front
doors, however.
Note
• If the battery has been disconnected and reconnected, it is possible
that the sliding/tilting roof does not close fully. Here you have to set the
control dial to the switch position and press it forward for about 10
seconds.
• It is necessary after each emergency operation (using crank handle)
to move the sliding/tilting roof into the basic position. Here you have to set
the control dial to the switch position and press it forward for about 10
seconds.
Opening and tilting
Comfort position
– Turn the switch to position ⇒ page 59, fig. 38.
Opening roof fully
– Turn the switch to position and hold it in this position
(spring-tensioned position).
Tilting roof
– Turn the switch to position .
The wind noise in the comfort position is less than when the roof is fully
opened.
The sun screen is also opened automatically when the roof slides open.
You can slide the sun screen into the opened or closed position by hand
when the sliding/tilting roof is closed.
Caution
It may be necessary during winter to remove any ice and snow in the area
of the sliding/tilting roof before opening it in order to prevent damaging the
opening mechanism.
Closing
Sliding closed/closing the sliding/tilting roof
– Turn the switch to position ⇒ page 59, fig. 38.
Safety closing
The sliding/tilting roof is equipped with an overload protection system. If
an obstacle (e.g. ice) prevents closing, the sliding/tilting roof stops and
opens completely. You can close the sliding/tilting roof completely without
overload protection by pressing the switch to the position ⇒ page 59,
fig. 38 at the front for as long as it takes for the sliding/tilting roof to shut
completely ⇒ .
WARNING
Close the sliding/tilting roof carefully - risk of injury!
AAA
A
ACABADA
A
A
A
s24s.book Page 60 Thursday, November 24, 2005 12:27 PM
Page 63
Unlocking and locking 61
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Convenience operation
You can also close an open sliding/tilting roof from the outside.
– Turn the key in the lock of the driver door into the closing posi-
tion or press the closing button of the radio remote control until
the sliding/tilting roof is closed ⇒ .
The closing process stops when one releases the key or the closing
button.
WARNING
Close the sliding/tilting roof carefully - risk of injury! The overload
protection system does not function with the convenience
closing.
Emergency operation
You can close the sliding/tilting roof by hand if the system is
defect.
Fig. 39 Detail of the
headliner: point for
positioning screwdriver
Fig. 40 Detail of the
headliner: Emergency
operation
s24s.book Page 61 Thursday, November 24, 2005 12:27 PM
Page 64
Unlocking and locking62
– Position the flat blade of a screwdriver carefully against the
rear edge of the cover of the power roof drive ⇒ page 61,
fig. 39.
– Pull the cover down.
– Take the crank handle out of the inside of the cover.
– Press the crank handle fully into the hexagon hole
⇒ page 61, fig. 40.
– Hold the crank pressed and turn it - the roof closes.
– Insert the crank handle into the cover again.
– Press on the cover again by first of all inserting the plastic lugs
and then pushing the cover up.
– Have the fault rectified by a specialist workshop.
Note
It is necessary after each emergency operation (using crank handle) to
move the sliding/tilting roof into the basic position. Here you have to press
the control dial forward to switch position ⇒ page 59, fig. 38 for about
10 seconds.
A1A
2
A
A
s24s.book Page 62 Thursday, November 24, 2005 12:27 PM
Page 65
Lights and Visibility 63
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Lights and Visibility
Lights
Switching lights on and off
Switching on side lights
– Turn the light switch into position 0.
Switching on the low beam and main beam
– Turn the light switch into position
.
– Press the main beam lever forward in order to switch on the
main beam ⇒ page 68, fig. 47.
Switching off all lights
– Turn the light switch into position.
Low beam comes on only if the ignition is switched on. After switching off
the ignition, the low beam is switched off automatically and only the side
lights come on.
On models fitted with right-hand steering the position of certain switches
differs from that shown in ⇒ fig. 41. The symbols which mark the switch
positions are identical, however.
In certain countries, the low beam is on a reduced brightness as well as
the side lights, when the ignition is switched on.
WARNING
Never drive with side lights on - risk of accident! The side lights are
not bright enough to light up the road sufficiently in front of you or
to be seen by other oncoming traffic. In this case, always switch on
the low beam when it is dark or if visibilty is poor.
Note
• An audible warning will sound if you withdraw the ignition key and open
the driver's door when the vehicle lights are still on.
• The acoustic warning signal is switched off over the door contact when
the driver's door is closed (ignition off). The vehicle can be parked with the
side lights on.
• If you park the car for a lengthy period, we recommend switching off
all lights, or leaving only the side lights switched on.
Fig. 41 Dash panel:
Light switch
s24s.book Page 63 Thursday, November 24, 2005 12:27 PM
Page 66
Lights and Visibility64
• The switching on of the described lights should only be undertaken in
accordance with the legal requirements.
• If a fault occurs in the light switch, the low beam comes on automati-
cally
• In the event of cool or humid weather conditons, the headlights can be
misted up from inside.
− The temperature difference between interior and external area of
the headlight lenses is decisive.
− When the driving lights are switched on, the light outlet surfaces are
free from mist after a short period. The headlight lenses can possibly
mist up at the border areas.
− It also concerns reverse light and turn signal lights.
− This mist has no influence on the life of the lighting system.
Automatic driving lamp control*
Switching on automatic driving lamp control*
– Turn the light switch ⇒ page 63, fig. 41 into position
.
Switching off automatic driving lamp control*
– Turn the light switch into position 0.
If the light comes on when the driving lamp control is switched on, the side
lights and low beam as well as licence plate light light up at the same time.
You can also switch on the side lights, fog lights and rear fog light with the
light switch .
If the automatic driving lamp control* is switched on, the light is controlled
by a light sensor in the mount of the interior rear mirror. If the light intensity
drops below the set value, e.g when driving during the day into a tunnel,
the low beam and the side lights as well as the licence plate light come on
automatically. If the light intensity increases again, the lights switch off
automatically.
Motorway lights
If the automatic driving lamp control* has been switched on and the
vehicle speed is over 140 km/h for at least 10 seconds, the side lights and
low beam are switched on automatically.
If the vehicle speed is below 65 km/h for at least 2 minutes, the lights are
switched off.
Rain lights
If you move the windshield wiper lever in the position slow wipe for more
than 5 seconds, the side lights and low beam are automatically switched
on. The light is switched off when the windshield wiper lever is no longer
than 4 minutes in the position for slow or intermittent wipe.
Fig. 42 Dash panel:
Light switch
s24s.book Page 64 Thursday, November 24, 2005 12:27 PM
Page 67
Lights and Visibility 65
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
WARNING
The automatic driving lamp control only operates as a support. The
driver is not released from his responsibility to inspect the light
and if necessary to switch on the light depending on the light
conditions. The light sensor cannot detect for example rain or
snow. Always switch on the low beam under these conditions
as well as when driving in the dark!
Note
• Do not affix any stickers in front of the light sensor, so that you do not
impair its function or put it out of operation.
• The same principles as for using the automatic driving lamp control
also apply to the light which is switched on manually ⇒ page 63.
Fog lights*
Switching on the fog lights
– First of all turn the light switch ⇒ fig. 43 into position
or .
– After this pull the light switch out to the first detent .
When the fog lights are operating, the symbol next to the light switch is
illuminated more intensely.
The rear fog light
Switching on the rear fog light
– First of all turn the light switch ⇒ fig. 43 into position
or .
– Pull the light switch out to the second detent .
The rear fog light warning light ⇒ page 30 lights up in the instrument
cluster when the fog light is switched off.
Only the rear fog light of the trailer lights up automatically when you are
towing a trailer using a factory-fitted towing device which is fitted with
the rear fog light.
The rear fog light is located in the rear light array on the driver's side.
Caution
The rear fog light should only be switched on if visibility is particularly poor
(conform with any varying legal provisions) to avoid dazzling vehicles
behind your vehicle.
Fig. 43 Dash panel:
Light switch
A
1
A
2
s24s.book Page 65 Thursday, November 24, 2005 12:27 PM
Page 68
Lights and Visibility66
Coming/Leaving Home Function*
This function makes it possible to switch on the lights for a short
time after leaving the vehicle or when approaching the vehicle.
Switching on Coming Home Function
– Switch off the ignition once the low beam is switched on.
– Leave the light switch in the position for low beam
.
– Close all the doors and the boot lid.
Switching on Leaving Home Function
– Unlock the vehicle with the radio remote control - the lights
come on.
Depending on equipment fitted the function Coming/Leaving Home
switches on the following lights:
• Parking lights,
• Low beam,
• Entry lighting in the exterior mirrors,
• Licence plate light.
Coming Home Function
The function Coming Home is only switched on, if the low beam was
switched on when the ignition is on.
The lights go out 80 seconds after closing all the doors and the boot lid.
If a door or the boot lid remains open, the lights go out 80 seconds after
switching off the ignition.
The light switch remains in the position for low beam also after switching
off the Coming Home Function, all lights are automatically switched off.
On vehicles fitted with automatic driving lamp control you can also switch
the light switch in the position ⇒ page 63, fig. 41. The function Coming
Home is controlled with the light sensor in the mount of the interior rear
mirror. If the light intensity is higher than the set value of the light sensor,
the Coming Home Function is not switched on after switching off the ignition.
Leaving Home Function
The function Leaving Home is controlled with the light sensor in the mount
of the interior rear mirror. If the light intensity is higher than the set value
of the light sensor, the Leaving Home Function is not switched on after
unlocking the vehicle with the radio remote control.
After unlocking the vehicle with the radio remote control, the lights come
on for 80 seconds. The Leaving Home Function is also switched off after
the ignition is switched on and after locking the vehicle.
If no door is opened within 30 seconds, the lights go out and the vehicle
is locked automatically.
Note
• If the Coming/Leaving Home Function is switched on constantly, the
battery will be heavily discharged particularly in short-haul traffic.
• The switching on of the described lights should only be undertaken in
accordance with the legal requirements.
• For vehicles fitted with fog lights you can change the illumination
period of the Coming/Leaving Home Function by means of the information
display* ⇒ page 28.
s24s.book Page 66 Thursday, November 24, 2005 12:27 PM
Page 69
Lights and Visibility 67
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Instrument lighting*
You can adjust the brightness of the instrument lighting.
Instrument lighting
– Switch on the light.
– Turn the control dial ⇒ fig. 44 to the desired intensity of the
instrument lighting
5)
.
Headlight range adjustment
Once the low beam is switched on you can then adapt the
range of the headlights to the load of the vehicle.
– Turn the control dial ⇒ fig. 45 until you have adjusted the low
beam so that oncoming traffic is not dazzled.
Settings
The positions correspond approximately to the following vehicle loads:
Front seats occupied, luggage compartment empty.
All seats occupied, luggage compartment empty.
All seats occupied, luggage compartment laden.
Driver seat occupied, luggage compartment laden.
Caution
Set the headlight beam adjustment in such a way as to avoid dazzling
oncoming traffic.
5)
On the information display* ⇒ page 23 the intensity of the lighting is automatically
set. The setting using the control dial ⇒ fig. 44 is only possible when driving in the
dark.
Fig. 44 Dash panel:
Instrument lighting
Fig. 45 Dash panel:
Lights and Visibility
A
-
A
1
A2A
3
s24s.book Page 67 Thursday, November 24, 2005 12:27 PM
Page 70
Lights and Visibility68
Note
Headlights fitted with Xenon bulbs* adapt automatically to the load and
driving state of the vehicle (e.g. accelerating, braking) when the ignition is
switched on and when driving.
Switch for hazard warning lights
– Press switch ⇒ fig. 46 to switch the hazard warning light
system on or off.
All the turn signal lights on the vehicle flash at the same time when the
hazard warning light system is switched on. The indicator light for the turn
signals and the indicator light in the switch also flash at the same time.
You can also switch on the hazard warning light system if the ignition is
switched off.
The hazard warning light system is switched on automatically if an airbag
is deployed in the event of an accident.
Please comply with any legal requirements when using the hazard
warning light system.
Note
Switch on the hazard warning light system if, for example:
• you encounter traffic congestion,
• your vehicle breaks down or an emergency situation occurs.
Turn signal and main beam lever
The parking lights and headlight flasher are also switched
on and off using the turn signal and main beam lever.
Fig. 46 Dash panel:
Switch for hazard
warning lights
Fig. 47 Turn signal
and main beam lever
s24s.book Page 68 Thursday, November 24, 2005 12:27 PM
Page 71
Lights and Visibility 69
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The turn signal and main beam lever perform the following functions:
Right
and left turn signal light
– Push the lever upwards or downwards ⇒ page 68, fig. 47.
– If you only wish to flash three times* (the so-called conven-
ience turn signal), push the lever briefly up to the upper or
lower pressure point and release it.
– Turn signal for changing lanes, in order to only flash briefly -
move the lever up or down to the pressure point and hold it in
this position.
Main beam
– Switch on the low beam.
– Push the lever forwards.
– Pull the lever back into the initial position in order to switch the
main beam off again.
Headlight flasher
– Pull on the lever of the steering wheel (sprung position) - the
main beam and warning light in the instrument cluster come
on.
Parking light
– Switch off the ignition.
– Push the lever up or down - the right-hand or left-hand parking
light is switched on.
Information concerning the function of the lights.
• The turn signal system only operates when the ignition is switched
on. The corresponding indicator light or in the instrument cluster also
flashes.
• The turn signal is automatically cancelled after negotiating a curve.
• The indicator light flashes at twice its normal rate if a bulb of the turn
signal light fails.
• The side light and rear light on the appropriate side of the vehicle are
switched on when the parking light is selected. The parking light function
only operates if the ignition is switched off.
• An acoustic warning signal will sound when the driver's door is opened
if the lever is not in the middle position after removing the ignition key. The
acoustic warning signal will stop just as soon as the driver's door is closed.
Caution
Use main beam or the headlight flasher only if this does not risk dazzling
other road users.
Note
• Use only in accordance with the legal requirements the described
lighting and signal systems.
s24s.book Page 69 Thursday, November 24, 2005 12:27 PM
Page 72
Lights and Visibility70
Interior lighting
Front interior lighting and lighting of storage
compartment on front passenger side
Switching the interior light on
– Press the switch to the left, the symbol
⇒ fig. 48
appears.
Switching the interior light off
– Press the switch into the middle position O.
– On the version without reading lights press the switch to
the right, the symbol O appears.
Door contact setting
– Press the switch to the right, the symbol
appears.
– On the version without reading lights press the switch into
the middle position
.
Reading lights*
– Press on one of the switches in order to switch the right or
left reading light on or off.
Lighting of storage compartment on the front passenger
side*
– When opening the flap of the storage compartment on the
front passenger side the lighting in the storage compartment
comes on.
– The light switches on automatically when the parking light is
switched on and goes out when the flap is closed.
The interior light comes on as soon as you unlock the car or open a door
or when the ignition key has been removed. The light goes out again
about 30 seconds after all the doors have been closed. The interior
lighting is switched off when you lock the car or switch the ignition on. This
only applies when the switch for the corresponding interior lights is
standing on the door contact setting.
The interior lighting goes off after about 10 minutes when a door has been
left open in order to avoid discharging the battery of the vehicle.
If the switch is in the position O (permanent lights), the interior lighting
goes off at the latest after 30 minutes in order to avoid discharging the
battery of the vehicle.
Note
We recommend having these bulbs replaced by a specialist garage.
Fig. 48 Detail of the
headliner: front interior
lighting
AAA
A
AAA
A
AAA
B
s24s.book Page 70 Thursday, November 24, 2005 12:27 PM
Page 73
Lights and Visibility 71
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Rear interior lighting*
The rear interior lighting ⇒ fig. 49 is actuated by moving the switch to the
symbol , O or to the middle position .
The same principles apply for the interior lighting at the rear as for the interior lighting at the front ⇒ page 70.
Note
We recommend having the bulb replaced by a specialist garage.
Front door warning light*
The warning light is located in the door trim panel below ⇒ fig. 50.
The warning light goes on every time the door is opened. The light goes
out about 10 minutes after opening the door in order to avoid discharging
the battery of the vehicle.
There is a reflector installed on some vehicles instead of the warning
light.
Luggage compartment light*
The lighting comes on automatically when the boot lid is opened. The
luggage compartment lighting will switch off again automatically if the boot
lid remains open for more than about 30 minutes.
Fig. 49 Roof liner light
at the rear
Fig. 50 Front door:
Warning light
s24s.book Page 71 Thursday, November 24, 2005 12:27 PM
Page 74
Lights and Visibility72
Entry lighting*
The lighting is positioned on the bottom edge of the exterior mirror.
The light beam is directed towards the entry area of the front door.
The light comes on after the doors have been locked or on opening the
boot lid. The light goes out after switching on the ignition or up to 30
seconds after closing all the doors, the bonnet and the boot lid.
If a door, the bonnet or the boot lid remains open, the light goes out within
2 minutes if the ignition is switched off.
WARNING
If the entry light comes on, do not touch its cover - risk of burns!
Visibility
Rear window heater
– You can switch the rear window heater on or off by pressing
the switch
⇒ fig. 51 - the indicator light in the switch comes
on or goes out.
The rear window heater only operates when the engine is running.
The rear window heater switches off automatically after 10 minutes.
For the sake of the environment
You should switch off the rear window heater as soon as the rear window
is clear. The reduced current consumption will have a favourable effect on
fuel economy ⇒ page 227, “Saving electricity”.
Fig. 51 Switch for rear
window heater
s24s.book Page 72 Thursday, November 24, 2005 12:27 PM
Page 75
Lights and Visibility 73
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• The position and the shape of the switch can differ depending on
equipment installed in the vehicle.
• If the on-board voltage drops, the rear window heater is switched off
automatically, in order to provide sufficient electrical energy for the engine
control.
Sun visors
You can pull the sun visor for the driver or front passenger out of the fixture
and swivel it toward the door in the direction of the arrow ⇒ fig. 52.
The vanity mirrors* in the sun visors are provided with covers. Push the
cover in direction of arrow .
WARNING
The sun visors must not be swivelled to the side windows into the
deployment area of the head airbags if any objects, such as ballpoint pens etc. are attached to them. This might result in injuries to
the occupants if the head airbag is deployed.
Fig. 52 Sun visor:
swivelling out
A1A
2
s24s.book Page 73 Thursday, November 24, 2005 12:27 PM
Page 76
Lights and Visibility74
Sun screen*
The sun screen is located in a housing on the luggage compartment cover. If required, you can remove the housing with the sun
screen from the luggage compartment cover.
Unrolling
– Pull the sun screen at the loop and hang it in the brackets
⇒ fig. 53.
Rolling up
– Take the sun screen out of the brackets and hold it at the
loop so that it can roll up slowly and without damage into
the housing on the luggage compartment cover.
Removing
– Unhook the fastening elements from the luggage compart-
ment cover .
– Roll up the sun screen again into the housing on the luggage
compartment cover.
– Press the locking button in the direction of arrow and take
out the sun screen in the direction or arrow ⇒ fig. 54.
Fig. 53 Unroll the sun
screen
Fig. 54 Remove the
sun screen
AAABABAAA
C
A1A
2
s24s.book Page 74 Thursday, November 24, 2005 12:27 PM
Page 77
Lights and Visibility 75
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Windshield wiper and wash system
Windscreen wipers
You can operate the windscreen wipers and automatic
wipe/wash using the windscreen wiper lever.
The windscreen wiper lever ⇒ fig. 55 has the following positions:
Finger-operated wiping
– If you wish to wipe the windscreen only briefly, push the lever
into the sprung position . If you hold the lever in the lower
position for more than 1 second, the wiper wipes faster.
Intermittent wipe
– Position the lever up into position .
– Set with the switch the desired break between the indi-
vidual wiper strokes
Slow wipe
– Position the lever up into position .
Fast wipe
– Position the lever up into position .
Automatic wipe/wash for windscreen
– Pull the lever towards the steering wheel into sprung position
, the wash system sprays immediately, the windscreen
wiper starts wiping a little later. The wash system and the
windscreen wiper operate simultaneously at a speed of more
than 120 km/h.
– Release the lever. The windscreen wash system stops and
the wiper continues for another 3 - 4 wiper strokes (depending
on the period of spraying of the windscreen). At a speed of
more than 120 km/h, the wiper wipes once again 5 seconds
after the last wiper stroke in order to wipe the last drops from
the windscreen.
Rain sensor*
– Move the lever into position .
– You can set the sensitivity of the sensor individually with
switch .
Wiping the rear window pane*
– Push the lever away from the steering wheel into position
- the widescreen wiper will operate every 6 seconds.
Fig. 55 Windscreen
wiper lever
A4A1AAA2A3A
5
A1AAA
6
s24s.book Page 75 Thursday, November 24, 2005 12:27 PM
Page 78
Lights and Visibility76
Automatic wipe/wash for the rear window pane*
– Press the lever from the steering wheel forward into the
sprung position , the wash system sprays immediately, the
windscreen wiper starts wiping a little later. As long as you
hold the lever in this position, the wiper operates as well as the
wash system.
– Letting go of the lever will cause the windscreen wash system
to stop and the wiper to continue for another 2 - 3 wiper
strokes (depending on the period of spraying of the windscreen). The lever will stay in position after releasing it.
Switching windscreen wipers off
– Move the lever back into its home position .
After the windscreen wiper switches off for the second time or the ignition
switches off for the fifth time, the rest position of the windscreen wiper
changes - this counteracts an early fatigue of the wiper rubbers.
The windscreen wipers and the wash system only operate if the ignition is
switched on and the bonnet is closed.
If the intermittent wipe is switched on, the intervals are also controlled
depending on speed.
The rain sensor* automatically regulates the break between the individual
wiper strokes depending on the intensity of the rain.
The rear window will be wiped again if the front window wipers are on
when reverse gear is selected.
The windscreen washer nozzles are heated* when the ignition is switched
on.
Top up with wash liquid ⇒ page 262.
Winter position
If the windscreen wipers are in rest position, they cannot be folded out
from the windscreen. For this reason we recommend adjusting the windscreen wipers in winter so that they can be folded out from the windscreen
easily. You can set this rest position as follows:
• Switch on the windscreen wipers.
• Switch off the ignition. The windscreen wipers remain in the position in
which they were when switching off the ignition.
You can also use the service position ⇒ page 77 as a winter position.
WARNING
• Properly maintained windscreen wiper blades are essential for
clear visibility and safe driving ⇒ page 77, “Replacing wiper blades
for the windscreen wipers”.
• Do not use the windscreen washer system at low temperatures,
without heating the windscreen beforehand. Otherwise the window
cleaner could freeze on the windscreen and restrict the view to the
front.
• The rain sensor only operates as a support. The driver is not
released from the responsibility to set the function of the windscreen wipers manually depending on the visibility conditions.
Caution
In frosty weather, please first of all check whether the windscreen wiper
blades are not frozen to the windscreen before switching them on.
Switching on windscreen wipers when the blades are frozen to the windscreen may result in damage both to the blades and the motor of the windscreen wipers!
A
7
A6A
0
s24s.book Page 76 Thursday, November 24, 2005 12:27 PM
Page 79
Lights and Visibility 77
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• If the slower or the faster wiper setting is switched on ⇒ page 75,
fig. 55 and the vehicle speed decreases to below 4 km/h, the next lower
wiper step is switched on automatically. At a speed increase of more than
8 km/h the previous wiper setting is established again.
• If there is an obstacle on the windscreen, the wiper will try to push
away the obstacle. If the obstacle continues to block the wiper, the wiper
stops after 5 cycles, in order to avoid a damage to the wiper. Remove the
obstacle and and switch on the wiper again.
Headlight cleaning system*
The headlights are being cleaned after the windscreen has been sprayed
for the fifth time, the low beam or main beam are switched on and the
windscreen wiper lever was held in the position ⇒ page 75, fig. 55 for
about 1 second.
The headlight washer nozzles are moved forward out of the bumper by the
water pressure for cleaning the headlights.
You should remove stubborn dirt (such as insect residues) from the headlight lenses at regular intervals, for example when refuelling. Please refer
to the following guidelines ⇒ page 237, “The headlight lenses”.
You should remove any snow from the fixtures of the washer nozzles and
clear ice in winter with a de-icing spray in order to ensure proper operation
of the cleaning system.
Replacing wiper blades for the windscreen wipers
One cannot fold out the wiper arms in the rest position from the
windscreen. Before replacing the wiper arms you must put them
into the service position.
Service position for changing wiper blades
– Close the bonnet.
– Switch the ignition on and then again off.
– Then press the windscreen wiper lever in the position
⇒ page 75, fig. 55 within 20 seconds - the wiper arms move
into the service position.
Taking off the wiper blade
– Fold windscreen wiper arm away from the windscreen and
position the wiper blade at right angles to the wiper arm ⇒ .
A2A3A
5
Fig. 56 Wiper blades
for the windscreen
A
4
s24s.book Page 77 Thursday, November 24, 2005 12:27 PM
Page 80
Lights and Visibility78
– Take off the wiper blade in direction of arrow ⇒ page 77, fig. 56
⇒ .
Attaching a wiper blade
– Push the new wiper blade over the wiper arm and turn the
wiper blade into the vertical position.
– Check whether the wiper blade is correctly attached.
– Fold the windscreen wiper arms onto the window and switch
on the ignition - the windscreen wiper arms move back into the
rest position.
Windscreen wiper blades in proper condition are essential to obtain good
visibility. Wiper blades should not be allowed to become dirtied by dust,
insect remains and preserving wax.
Juddering or smearing of the wiper blades could then be due to wax residues left on the windscreen by vehicle washing in automatic vehicle wash
systems. It is therefore important to degrease the lips of the winscreen
wiper blades after every pass through an automatic vehicle wash
system.
WARNING
• The ignition must not be switched on if the front windscreen
wiper arms are folded out. The wiper blades would move back into
their rest position and while doing so damage the paintwork of the
bonnet.
• If the windscreen wipers are handled carelessly, there is a risk
of damage to the windscreen.
• You should clean the wiper blades regularly with a windscreen
cleaner in order to avoid any smears. Clean a wiper blade with a
sponge or cloth if it is very dirty, for example from insect residues.
• Replace the windscreen wiper blades once or twice a year for
safety reasons. Windscreen wiper blades are available from Škoda
dealers.
Replacing the wiper blade on the rear window wiper
Taking off the wiper blade
– Fold windscreen wiper arm away from the windscreen and
position the wiper blade at right angles to the wiper arm
⇒ fig. 57.
– Hold the window wiper arm at the top end with one hand.
– With the other hand unlock the locking button in the direc-
tion of arrow and remove the wiper blade.
WARNING (continued)
Fig. 57 Wiper blade for
the rear window
A
A
s24s.book Page 78 Thursday, November 24, 2005 12:27 PM
Page 81
Lights and Visibility 79
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Attaching a wiper blade
– Position the wiper blade onto the wiper arm and lock the
locking button .
– Check whether the wiper blade is correctly attached.
The same remarks apply here as for ⇒ page 77, “Replacing wiper blades
for the windscreen wipers”.
Rear-view mirror
Manual dimming interior rear-view mirror
Basic position
– Pull the lever on the bottom edge of the mirror forward.
Dimming mirror
– Pull the lever on the bottom edge of the mirror back.
Automatic dimming interior mirror*
Switching on the automatic dimming
– Press the button - the warning light lights up ⇒ fig. 58.
Switching off the automatic dimming
– Press again the button - the warning light goes out .
If the automatic dimming is switched on, the mirror dims automatically
depending on the light striking the mirror from the rear. The mirror has no
lever on the bottom edge of the mirror. When the interior lights are
switched on or the reverse gear is engaged, the mirror always moves back
into the basic position.
Note
• Automatic mirror dimming operates only properly if the sun screen* for
the rear window is not in use or the light striking the rear of the interior
rear-view mirror is not affected by other objects.
A
A
Fig. 58 Automatic
dimming interior mirro
r
ABAAABA
A
s24s.book Page 79 Thursday, November 24, 2005 12:27 PM
Page 82
Lights and Visibility80
• Do not affix any stickers in front of the light sensor, so that you do not
impair the automatic dimming function or put it out of operation.
• If you switch off the automatic dimming interior rear-view mirror, also
the exterior mirror dimming is switched off.
Exterior mirrors
You can adjust the exterior mirrors electrically*.
The exterior mirror heater only operates when the engine is
running and up to an outside temperature of +20 °C.
Heating of the external mirror
– Turn the rotary knob to position
⇒ fig. 59.
Adjusting left and right exterior mirrors simultaneously
– Turn the rotary knob to position
. The movement of the mirror
surface is identical to the movement of the rotary knob.
Adjusting the right-hand exterior mirror
– Turn the rotary knob to position
. The movement of the mirror
surface is identical to the movement of the rotary knob.
Switching off operating control
– Turn the rotary knob to position
.
Tilting surface of front passenger exterior mirror*
When the rotary knob is in position ⇒ fig. 59 and the reverse gear is
engaged, the surface of the mirror tilts down slightly. This provides an aid
in seeing the kerb of the pavement when parking the car.
The mirror returns back into its initial position, if the speed is more than 15
km/h or the rotary knob is moved out of the position and put into another
position.
Memory for exterior mirrors*
On vehicles fitted with a memory for the driver seat, the relevant setting of
the exterior mirror is also stored automatically when the seat position is
stored ⇒ page 82.
WARNING
• Convex (curved outward) or aspherical exterior mirrors
increase the vision field. They do, however, make objects appear
smaller in the mirror. These mirrors are only of limited use, therefore, for estimating distances to the following vehicles.
• Use whenever possible the interior rear-view mirror, for esti-
mating the distances to the following vehicles.
Fig. 59 Inner part of
door: Rotary knob
s24s.book Page 80 Thursday, November 24, 2005 12:27 PM
Page 83
Lights and Visibility 81
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• Do not touch the surface of the exterior mirrors if the exterior mirror
heater is switched on.
• You can set the exterior mirrors by hand, if the power setting function
fails at any time, by pressing on the edge of the mirror surface.
• Contact your specialist garage if a fault exists with the power setting of
the exterior mirrors.
Automatic dimming exterior mirror*
The exterior mirrors are dimmed together with the automatic dimming interior mirror. If the automatic dimming is switched on, the mirror dims auto-
matically depending on the light striking the mirror from the rear.
When the interior lights are switched on or the reverse gear is engaged,
the mirror always moves back into the basic position (not dimmed).
Note
• Automatic mirror dimming operates only properly if the sun screen* for
the rear window is not in use or the light striking the rear of the interior
rear-view mirror is not affected by other objects.
• Do not affix any stickers in front of the light sensor, so that you do not
impair the automatic dimming function or put it out of operation.
• If you switch off the automatic dimming interior rear-view mirror, also
the exterior mirror dimming is switched off.
s24s.book Page 81 Thursday, November 24, 2005 12:27 PM
Page 84
Seats and Stowage82
Seats and Stowage
Front seats
Basic information
The front seats have a wide range of different settings and can thus be
matched to the physical characteristics of the driver and front passenger.
Correct adjustment of the seats is particularly important for
• safely and quickly reaching the controls,
• a relaxed, fatigue-free body position,
• achieving the maximum protection offered by the seat belts and
the airbag system.
WARNING
• Never transport more occupants than the maximum seating in
the vehicle.
• Each occupant must correctly fasten the seat belt belonging to
the seat. Children must be fastened ⇒ page 202, “Transporting children safely” with a suitable restraint system.
• The front seats and the head restraints must always be adjusted
to match the body size of the seat occupant as well as the seat belts
must always be correctly fastened in order to provide an optimal
protection for you and your occupants.
• Always keep your feet in the footwell when the car is being
driven - never place your feet on the instrument panel, out of the
window or on the surfaces of the seats. This is particularly important for the front seat passenger. You will be exposed to increased
risk of injury if it becomes necessary to apply the brake or in the
event of an accident. If an airbag is deployed, you may suffer fatal
injuries when adopting an incorrect seated position!
• It is important for the driver and front passenger to maintain a
distance of at least 25 cm from the steering wheel or dash panel.
Not maintaining this minimum distance will mean that the airbag
system will not be able to properly protect you - hazard! The front
seats and the head restraints must always also be correctly
adjusted to match the body size of the occupant.
• Ensure that there are no objects in the footwell as any objects
may get behind the pedals during a driving or braking manoeuvre.
You would then no longer be able to operate the clutch, to brake or
accelerate.
WARNING (continued)
s24s.book Page 82 Thursday, November 24, 2005 12:27 PM
Page 85
Seats and Stowage 83
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Adjusting the front seats
Adjusting a seat in a forward/back direction
– Pull the lever ⇒ page 83, fig. 60 up and push the seat into
the desired position.
– Release the lever and push the seat further until the lock
is heard to engage.
Adjusting height of seat*
– Lift the seat if required by pulling or pumping lever
upwards.
– Lower the seat if required by pushing or pumping lever
downwards.
Adjusting angle of backrest
– Relieve any pressure on the backrest (do not lean on it) and
turn the handwheel ⇒ page 83, fig. 60 to adjust the desired
angle of the backrest.
Adjusting lumbar support*
– Turn the handwheel until you have set the most comfort-
able curvature of the seat upholstery in the area of your spine.
The driver's seat should be adjusted in such a way that the pedals can be
pressed to the floor with slightly bent legs.
The backrest on the driver's seat should be adjusted in such a way that
the upper point of the steering wheel can be easily reached with slightly
bent arms.
WARNING
• Only adjust the driver seat when the vehicle is stationary - risk
of injury!
• Take care when adjusting the seat! Adjusting the seat without
care can lead to bruises or injuries.
• The backrests must not be angled too far back when driving
otherwise this will affect proper operation of the seat belts and of
the airbag system - risk of injury!
Fig. 60 Controls at
seat
A
1
A1A
2
A
2
A3A
4
s24s.book Page 83 Thursday, November 24, 2005 12:27 PM
Page 86
Seats and Stowage84
Adjusting front seats electrically*
Adjusting seats
Adjusting seat
– Adopt the correct seated position ⇒ page 82.
– Press switch or ⇒ page 84, fig. 61 in the direction of the
desired setting.
Adjusting lumbar support
– Press the switch front ⇒ page 84, fig. 61 in order to enlarge
the curvature of the lumbar support.
– Press the switch rear in order to reduce the curvature of
the lumbar support.
– Press the switch top in order to adjust the curvature of the
lumbar support higher.
– Press the switch bottom in order to adjust the curvature of
the lumbar support lower.
Switch is operated in order to move the seat up/down and
forward/back, while switch is operated in order to move the backrest
forward or back.
WARNING
• Only adjust the driver seat when the vehicle is stationary - risk
of injury!
• Caution when adjusting the seat! You may suffer injuries or
bruises as a result of adjusting the seat without paying proper
attention.
• In view of the fact that the seats can also be adjusted when the
ignition is switched off (even when ignition key withdrawn), you
should never leave children unattended in the car.
• The backrests must not be angled too far back when driving
otherwise this will affect proper operation of the seat belts and of
the airbag system - risk of injury!
Note
If the movement of the seat is inadvertently interrupted during an adjustment, once again press the switch in the appropriate direction and
continue with the adjustment of the seat to the end.
Fig. 61 Side view:
Controls for adjusting
the seat
AAABA
C
A
C
A
C
A
C
A
A
A
B
s24s.book Page 84 Thursday, November 24, 2005 12:27 PM
Page 87
Seats and Stowage 85
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Storing setting
Storing seat and exterior mirror settings for driving forward
– Switch on the ignition.
– Adjust the seat ⇒ page 84.
– Adjust both exterior mirrors ⇒ page 80.
– Press button SET ⇒ page 85, fig. 62.
– Press one of the memory buttons within 10 seconds after
pressing the button SET - an acknowledgement signal
confirms that the seat setting is stored..
Storing exterior mirror setting for reversing*
– Switch on the ignition.
– Turn the exterior mirror control to position
⇒ page 80.
– Engage reverse gear.
– Move the right exterior mirror into the desired position
⇒ page 80.
– Switch back into its original position. The set position of the
exterior mirror is stored in the current memory.
Memory buttons
Memory for the seat offers the possibility to store the individual driver seat
and external mirror position. An individual position can be allocated to
each of the three memory buttons ⇒ page 85, fig. 62, that is three in
total. After pressing the corresponding memory button , the seat and
the exterior mirror are automatically moved into the positions which have
been allocated to this button ⇒ page 86.
Emergency Off
You can interrupt the setting operation at any time, if you operate any
button of the driver seat.
Note
• When storing settings with the memory buttons, we recommend that
you begin with the front button and assign a memory button to each additional driver.
• Each new setting stored with the same button erases the previous
setting.
• Each time you store the seat and exterior mirror settings for driving
forward you also have to re-store the individual setting of the exterior
mirror on the passenger side for reversing.
Fig. 62 Driver seat:
Memory buttons and
SET button
A
A
A
B
A
B
A
B
s24s.book Page 85 Thursday, November 24, 2005 12:27 PM
Page 88
Seats and Stowage86
Assigning remote control to the memory buttons
After storing the settings of the seat and exterior mirrors, you
have 10 seconds in order to assign the remote control to the
appropriate memory button.
– Withdraw the ignition key.
– Press the button for unlocking the vehicle ⇒ page 52. The
setting is stored with the memory button which you have
selected.
If you wish to be able to retrieve the settings which are stored in the
memory by also using the remote control, you have to assign the remote
control to a memory button in each case.
If you wish, you can obtain an additional key with radio remote control
from a Škoda dealer and then assign the radio remote control to another
memory button.
Note
• If the remote control had previously been assigned to another memory
button, this setting is then erased by the new assignment.
• If you assign the remote control to a memory button which has already
been assigned to a remote control, the old assignment is also replaced by
a new assignment in this case.
• The assignment of the remote control to a memory button is retained,
however, after reassigning the seats and exterior mirrors.
Retrieving settings of the seat and mirrors
You can retrieve the stored settings either with the
memory buttons or with the remote control*.
Retrieving settings with memory buttons
– In order to retrieve the stored setting, you have two possibili-
ties:
– One-touch automatic memory: Briefly press the desired
memory button ⇒ page 85, fig. 62. The seat and exterior
mirror are moved automatically into the stored positions (this
applies only if the ignition is switched on and the speed is less
than 5 km/h).
– Memory keying: Press and hold the desired memory button
pressed long enough until the seat and the exterior mirror
are moved into the stored positions.
Retrieving settings with remote control
– If the driver door is closed and the ignition is switched off,
briefly press the unlock button of the remote control ⇒ page 52
and then open the driver door.
– The seat and exterior mirrors now move automatically into the
stored positions.
Retrieving setting of exterior mirror for reversing*
– Turn the rotary knob for the exterior mirror setting into the
position
⇒ page 80 before engaging the reverse gear.
A
B
A
B
s24s.book Page 86 Thursday, November 24, 2005 12:27 PM
Page 89
Seats and Stowage 87
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
The mirror returns back into its initial position, after the rotary knob is
moved out of the position and put into another position or if the speed is
more than 15 km/h.
Emergency Off
You can interrupt the setting operation at any time, if you operate any
button of the driver seat.
Head restraints
Best protection is achieved if the top edge of the head restraint is
at the same level as the upper part of your head.
Adjusting the height of a head restraint
– Grasp the side of the head restraint with both hands and push
it up or down in direction of arrow ⇒ fig. 63.
– If you wish to push the head restraint of the front seat down-
wards, you must additionally press the safety button ⇒ fig. 64.
– If you wish to set the rear head restraint in the lower position,
you must additionally press the safety button.
Adjusting the angle of a head restraint
– You can adapt the head restraint by adjusting its angle to your
head ⇒ fig. 63. Adjusting the angle of the head restraint
provides enhanced comfort for the user.
Fig. 63 Adjusting head
restraint
Fig. 64 Removing a
head restraint
s24s.book Page 87 Thursday, November 24, 2005 12:27 PM
Page 90
Seats and Stowage88
Removing and installing a head restraint
– Pull the head restraint up out of the backrest of the seat as far
as the stop (on the rear head restraints fold forward the seat
backrest).
– Press the locking button in the direction of arrow ⇒ fig. 64 and
pull the head restraint out.
– To re-insert the head restraint, push it down into the backrest
of the seat far enough until you hear the locking button
engage.
The head restraints of the front seats can be adjusted for angle and
height. The outer head restraints at the rear can only be adjusted for
height. The middle rear head restraint* is adjustable in two positions.
The head restraints must be adjusted to match the size of the seat occupant. Correctly adjusted head restraints together with the seat belts offer
effective protection for the occupants ⇒ page 179.
Active head restraints*
The front seats can be equipped with active head restraints, which protect
the occupants from injury to the cervical vertebra in the event of a rear
impact
WARNING
• The head restraints must be correctly adjusted in order to offer
effective protection for the occupants in the event of an accident.
• Do not drive under any circumstance with removed head
restraints - risk of injury!
• If the rear seats are occupied, the rear head restraint must not
be in the lower position.
Heating the front seats*
The seating and leaning surfaces of the front seats can be heated
when the ignition is switched on.
Front seats
– Heating on the driver's and front pasenger's seat can be
switched on and regulated by turning the control dial ⇒ fig. 65.
– The system is switched off by turning the control dial to the
home position “0”.
Caution
• You should not kneel on the seats or otherwise apply pressure at
specific points in order to avoid damaging the heating elements of the seat
heaters.
• Do not clean the seats moist ⇒ page 239.
Fig. 65 Dash panel:
Control dial for heating
the front seats
s24s.book Page 88 Thursday, November 24, 2005 12:27 PM
Page 91
Seats and Stowage 89
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
• The seat heating should only be switched on when the engine is
running. This has a significant effect of saving on the battery capacity.
• If the on-board voltage drops, the seat heating is switched off automat-
ically, in order to provide sufficient electrical energy for the engine
control.
Rear seats
Folding the rear seats forwards
To enlarge the luggage compartment, the rear seats can be
folded forwards, if necessary remove the rear seats. Both rear
seats can be folded forward individually on vehicles with divided
rear seats*.
Folding the rear seats forwards
– In order to avoid causing any damage when folding the rear
seat forward it is important to adjust the front seats so that no
damage can occur when this is done.
– Pull up the rear seats in the direction of arrow and fold
forwards in direction of arrow ⇒ fig. 66.
– Press the unlocking knob and fold the rear seat backrest
forwards ⇒ fig. 67.
If the front seats are too far back, we recommend that you have the rear
head restraints removed before the seat backrests are folded forward.
Store the removed head restraints in such a way that they cannot be
Fig. 66 Folding the
rear seats forwards
Fig. 67 Unlock the seat
backrest
A1A
2
A
A
s24s.book Page 89 Thursday, November 24, 2005 12:27 PM
Page 92
Seats and Stowage90
damaged or soiled. Please refer to the guidelines ⇒ page 92, “Luggage
compartment”.
Folding the rear seats back into position
Folding the rear seats back into position
– Install the head restraint in the partially lifted rear seat back-
rest.
– Place the rear lateral seat belt behind the edge of the side
trim panel ⇒ fig. 68.
– Then push the seat backrest back into the upright position
until the locking button clicks into place - check by pulling on
the rear seat backrest.
– Make sure that the red pin is covered ⇒ page 89, fig. 67.
– Fold the rear seats back into its original position.
WARNING
• The belts and the belt locks must be in their original position
after folding back the rear seats and seat backrests - they must be
ready to use.
• The seat backrests must be securely interlocked in position so
that no objects in the luggage compartment can slide into the
passenger compartment if there is sudden braking - risk of injury.
• Pay attention that the rear seat backresst are correctly inter-
locked. It is only then that the three-point seat belt for the middle
seat can reliably fulfil its function.
• Before folding the seat backrest back into the secure position,
place the rear lateral seat belt behind the edge of the side trim
panel. Take suitable measures to prevent that the seat belt is
jammed between the seat backrest and the side trim panel is thus
damaged.
Fig. 68 Lock the seat
backrest
A
C
A
B
s24s.book Page 90 Thursday, November 24, 2005 12:27 PM
Page 93
Seats and Stowage 91
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Remove the rear seats
You can enlarge the luggage compartment on vehicles with
divided rear seats* by removing the rear seat.
Removing
– Fold the rear seats forwards completely
– Press the wire clamps in the direction of the arrow ⇒ fig. 69
and remove the rear seats from its holder.
Installing
– Press the wire clamp in the direction of the arrow and place
the seat upholstery in its holder.
– Fold the rear seats back into its original position.
Armrest of rear seats*
– You can fold down the armrest at the loop to enhance occu-
pant comfort ⇒ fig. 70.
Pedals
Concerning a secure depressing of the pedal, you should use only footmats from the Škoda genuine accessories.
Operation of the pedals must not be hindered!
WARNING
• Greater pedal distances may be needed when there is a fault in
the brake system.
Fig. 69 Remove the
rear seats
Fig. 70 Rear seats:
Armrest
s24s.book Page 91 Thursday, November 24, 2005 12:27 PM
Page 94
Seats and Stowage92
• Do not place any footmats or other additional floor coverings in
the area of the pedals in order to ensure that all the pedals can be
fully depressed and are able to return unobstructed to their initial
position - risk of accident!
• There must be no objects on the floor which could roll under the
pedals. You would then no longer be able to apply the brakes,
operate the clutch or accelerator - risk of accident!
Luggage compartment
Loading the luggage compartment
Please observe the following in the interest of having good
handling characteristics of your vehicle:
– Distribute the items of luggage as evenly as possible.
– Place heavy objects as far forward as possible.
– Attach the items of luggage to the lashing eyes or the safety
net* ⇒ page 93.
In the event of an accident, there is such a high kinetic energy which is
produced by small and light objects that they can cause severe injuries.
The magnitude of the kinetic energy depends on the speed at which the
vehicle is travelling and on the weight of the object. The speed at which
the vehicle is travelling is in this case the more significant factor.
Example: In the event of a frontal collision at a speed of 50 km/h, an unsecured object with a weight of 4.5 kg produces an energy, which corre-
sponds to 20 times its own weight. This means that it results in a weight
of approx. 90 kg. You can imagine the injuries that can occur, if this “bullet”
is flying through the interior compartment and hits an occupant.
WARNING
• Store the objects in the luggage compartment and attach them
to the lashing eyes.
• Loose objects in the passenger compartment can be thrown
forward during a sudden manoeuvre or in case of an accident and
can injure the occupants or other oncoming traffic. This risk is still
increased, if the objects which are flying around are hit by a
deployed airbag. In this case, the objects which are thrown back
can injure the occupants - hazard.
• Please note that the handling properties of your vehicle may be
affected when transporting heavy objects as a result of the
displacement of the centre of gravity. The speed and style of
driving must be adjusted accordingly.
• The items carried in the luggage compartment should be stored
in such a way that no objects are able to slip forward if there are any
sudden driving or braking manoeuvres undertaken - risk of injury!
• Never drive with the boot lid slightly ajar or even fully opened
otherwise exhaust gases may get into the interior of the vehicle risk of poisoning!
• On no account exceed the permissible axle loads and the
permissible gross weight of the vehicle - risk of accident!
• Never transport occupants in the luggage compartment!
Caution
Please ensure that the heating elements of the rear window heater are not
damaged as a result of objects sliding in this area.
WARNING (continued)
s24s.book Page 92 Thursday, November 24, 2005 12:27 PM
Page 95
Seats and Stowage 93
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Note
Tyre pressure must be adjusted to the load ⇒ page 264, fig. 199.
Lashing eyes
Eyes are located on the sides of the loading area for lashing the goods to
be loaded.
You can also attach a floor fixing net* to these eyes for lashing small
objects.
The floor fixing net* and the installation instruction are located in a
container under the floor covering of the luggage compartment behind the
spare wheel.
WARNING
• The load to be transported must be fixed in place in such a way
that it cannot move during the journey and when braking.
• If the items of luggage or objects are attached to the lashing
eyes with unsuitable or damaged lashing straps, injuries can occur
in the event of braking manoeuvres or accidents. In order to
prevent the items of luggage being thrown forward, always use
suitable lashing straps which are firmly attached to the lashing
eyes.
Fig. 71 Luggage
compartment: Lashing
eyes (Octavia)
Fig. 72 Luggage
compartment: Lashing
eyes (Estate car)
s24s.book Page 93 Thursday, November 24, 2005 12:27 PM
Page 96
Seats and Stowage94
Note
On vehicles in the version Octavia, the top front lashing eyes are located
behind the seat backrest ⇒ page 93, fig. 71.
Fixing nets - Net programme Octavia*
Fixing examples of the fixing net as horizontal pocket ⇒ fig. 73 and vertical
pocket ⇒ fig. 74.
The fixing net and the installation instruction are located in a container
under the floor covering of the luggage compartment behind the spare
wheel.
WARNING
The whole strength of the net makes it possible to load the pocket
with objects of up to 1.5 kg in weight. Heavy objects are not
secured sufficiently - risk of injury and net damage!
Caution
Do not place any objects with sharp edges in the nets - risk of net
damage.
Fig. 73 Fixing net:
Horizontal pocket
Fig. 74 Fixing net:
Vertical pocket
s24s.book Page 94 Thursday, November 24, 2005 12:27 PM
Page 97
Seats and Stowage 95
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
Fixing nets - Net programme estate car*
Fixing examples of the fixing net as pocket ⇒ fig. 75 and as division of the
luggage compartment ⇒ fig. 76.
The fixing net and the installation instruction are located in a container
under the floor covering of the luggage compartment behind the spare
wheel.
WARNING
The whole strength of the net makes it possible to load the pocket
with objects of up to 1.5 kg in weight. Heavy objects are not
secured sufficiently - risk of injury and net damage!
Caution
Do not place any objects with sharp edges in the nets - risk of net
damage.
Folding double hooks* (Octavia)
Fig. 75 Fixing net:
Pocket
Fig. 76 Fixing net:
Division of the luggage
compartment
Fig. 77 Luggage
compartment: Folding
double hooks
s24s.book Page 95 Thursday, November 24, 2005 12:27 PM
Page 98
Seats and Stowage96
Folding double hooks for attaching small items of luggage, such as bags
etc. ⇒ page 95, fig. 77 are provided on one or both sides of the luggage
compartment depending on the equipment installed in the vehicle.
An item of luggage weighing up to 5 kg can be attached to each side of
the double hook.
Folding hooks (estate car)
Folding hooks for attaching small items of luggage, such as bags etc., are
provided on both sides of the luggage compartment ⇒ fig. 78.
An item of luggage weighing up to 10 kg can be attached to the hook.
Fixing of the floor covering of the luggage
compartment
There is a loop (Octavia) or there are hooks (estate car) located on the
floor covering of the luggage compartment. You can fix the raised floor
Fig. 78 Luggage
compartment: Folding
hooks
Fig. 79 Luggage
compartment: Fixing of
the floor covering
(Octavia)
Fig. 80 Luggage
compartment: Fixing of
the floor covering
(Estate car)
s24s.book Page 96 Thursday, November 24, 2005 12:27 PM
Page 99
Seats and Stowage 97
Using the system Safety Driving Tips General Maintenance Breakdown assistance Technical Data
cover with a hook to the luggage compartme nt cover (Octavia) ⇒ fig. 79 as
if one needs to reach the spare wheel or to the frame of the boot lid (estate
car) ⇒ fig. 80.
Luggage net* (Octavia)
The luggage net is designed for the tranportation of lighter objects.
WARNING
• In the luggage net you must only store objects (up to a total
weight of 1.5 kg). Heavy objects are not secured sufficiently - risk
of injury!
• No objects with sharp edges should be stored in the luggage
net, because they can damage the luggage net.
Luggage compartment cover* (Octavia)
You can use the luggage compartment cover behind the
head restraints for storing light and soft items.
The luggage compartment cover can be removed as required if
one must transport bulky goods.
– Unhook the support straps on the tailgate ⇒ fig. 82.
– Place the cover on the side supports.
– Pull the cover out of the holder horizontally to the rear.
– Install again by pushing the luggage compartment cover
forwards into the holder and hanging the support straps
on the tailgate.
You can stow the removed luggage compartment cover behind the rear
seat backrest.
Fig. 81 Luggage
compartment: Luggage
net
Fig. 82 Removing the
luggage compartment
cover
A
1
A
2
A2A
1
s24s.book Page 97 Thursday, November 24, 2005 12:27 PM
Page 100
Seats and Stowage98
WARNING
No objects should be placed on the luggage compartment cover,
the vehicle occupants could be endangered if there is sudden
braking or the vehicle collides with something.
Caution
Please ensure that the heating elements of the rear window heater are not
damaged as a result of objects placed in this area.
Note
Opening the tailgate also lifts up the luggage compartment cover.
Luggage compartment cover (estate car)
Unrolling
– Pull the luggage compartment cover in direction of arrow
as far as the stop into the secured position ⇒ fig. 83.
Rolling up
– Press the cover in the handle area in direction of arrow , the
cover rolls up automatically.
Removing
– Have the luggage compartment cover removed to transport
bulky goods. Press the slider from the side in the direction of
arrow and remove the luggage compartment cover in the
direction of arrow ⇒ fig. 84.
WARNING
No objects should be placed on the luggage compartment cover.
Fig. 83 Luggage
compartment: The
luggage compartment
cover
Fig. 84 Luggage
compartment:
Removing the luggage
compartment cover
A1A2A3A
4
s24s.book Page 98 Thursday, November 24, 2005 12:27 PM
Loading...