Škoda India 2012 Owner's Manual
SIMPLY CLEVER
Rapid
Owner's Manual
Signs and symbols
Indicates a reference to a section with important information and
safety warnings that should always be heeded.
The symbol indicates situations in which the vehicle must be stopped
as quickly as possible.
® The symbol indicates registered trademarks. However, the absence
of this symbol does not constitute a waiver of any rights associated
with intellectual property.
»
Cross-reference to a red, orange, or yellow warning in the same section or on the stated page, pointing out possible risks that can cause
»
serious personal injuries and how to help prevent them.
»
» Cross reference to a Notice about possible property damage, in the
same section or on the stated page.
DANGER
Texts with this symbol contain information regarding hazardous situations
which will cause death or severe injuries if not avoided.
WARNING
Texts with this symbol contain information regarding hazardous situations
which could cause death or severe injuries if not avoided.
CAUTION
Texts with this symbol contain information regarding hazardous situations
which could cause minor or moderate injuries if not avoided.
NOTICE
Texts with this symbol contain information regarding situations which could
cause vehicle damage if not avoided.
Texts with this symbol contain information about the environment and how
you can help to protect it.
Texts with this symbol contain supplementary information.
Table of Contents
Abbreviations
Vehicle overview
Vehicle interior 4
Overview of the driver’s side 4
Instrument cluster 5
Warning and indicator lights 5
Instruments 7
ŠKODA information system
Before driving
Before you start 12
Driving tips
Technical data
Opening and closing 16
Vehicle key set
Central locking and closing system 19
Doors
Boot lid
Power windows 25
Sitting properly and safely
Adjusting the seat position 27
Seat features
Seat belts
Airbag system 40
Child seats (accessories)
Lights and visibility 48
Lights
Sun screen
Windscreen wipers and washers 53
Mirrors
48
Transporting 56
Driving tips 56
Useful equipment 59
Storage facilities 59
Cup holders 62
Power socket 64
When driving
Starting, shifting gears, parking
Starting and stopping the engine 66
Shifting gears 70
Braking, stopping and parking 75
10
Driving in an environmentally conscious
manner
Steering 84
Air conditioning
Air conditioning system
12
At the petrol station 92
14
Refuelling
Fuel 96
16
Maintenance, cleaning, servicing
21
23
In the engine compartment
Preparing to work in the engine compartment
Engine oil
27
Engine coolant
Vehicle battery 109
33
34
Care and maintenance of the vehicle
Maintaining and cleaning the vehicle exterior
44
Maintaining and cleaning the interior 119
Wheels and tyres
Accessories, replacement of parts, repairs and
modifications
52
Consumer information
Engine control and emission control system 139
55
Do-it-yourself
Practical information 140
Questions and answers 140
In an emergency 142
Emergency closing or opening 144
Tool kit 147
Wheel trims 149
Wheel change 151
66
Fuses 155
Changing a bulb 157
Jump starting 162
Tow-starting and towing 164
82
Index
86
86
92
99
99
103
106
112
112
122
131
137
Table of Contents
1
Abbreviations
Abbreviation Meaning
rpm Engine revolutions per minute (engine speed).
ABS Anti-lock brake system.
AG6 6-speed automatic gearbox.
ccm Cubic centimetres. Unit for stating the displacement.
CO
DIN Deutsches Institut für Normung (German Institute for Stand-
EN European Standard.
EPC Engine control unit (Electronic Power Control).
ETC Electronic Toll Collection System.
g/km Carbon dioxide output in grams per kilometre.
kW Kilowatt, engine power rating.
LED Light Emitting Diode.
MFA Multi-function display (German abbreviation).
MKB Engine code letter (German abbreviation).
Nm Newton metres, unit for specifying engine torque.
BHP Brake horse power, (obsolete) engine power rating.
RON Research Octane Number, unit for specifying the knock resist-
SG5 5-speed manual gearbox.
TDI
Carbon dioxide.
2
ardization).
ance of petrol fuel.
®
Diesel engine with direct injection and turbocharging (Turbocharged Direct or Diesel Injection).
Ð
2
Abbreviations
Abbreviations
3
Vehicle overview
Vehicle interior
Overview of the driver’s side
Overview of the driver’s side
Fig. 1
1
Button for rear window heater » page 87
2
Button for switching the hazard warning light system » page 142
3
Air outlet » page 86
4
Lever for: » page 49
Main beam
›
Headlight flasher
›
Turn signal lights
›
Parking light
›
5
Horn (works only with the ignition on)
6
Instrument cluster:
Instruments » page 7
›
Display » page 7
›
Warning and indicator lights » page 5
›
7
Lever for windscreen wipers and washers: » page 53
Windscreen wipers
›
“Flick wipe” 1x
›
Windscreen wipers
›
Automatic wash-wipe for the windscreen
›
Rocker button to operate the multi-function display » page 10
›
8
Air outlet » page 86
9
Switch for adjusting the exterior mirrors » page 55
10
Central locking button for locking and unlocking the vehicle » page 19
11
Button to unlock the boot lid » page 23
12
Light switch » page 48
Light off
›
Parking lights and low beam lights
›
Fog lights
›
13
Headlamp beam adjustment » page 50
14
Ignition lock » page 67
15
Driver’s front airbag » page 40
16
Lever for the adjustable steering column » page 27
17
Fuse box cover » page 155
18
Control element for:
Manual air conditioning and heating » page 86
›
Climatronic and heating » page 86
›
19
Radio (factory installed) » booklet Radio
Ð
4
Vehicle overview
Instrument cluster
Warning and indicator lights
The warning and indicator lights indicate warnings » , problems » or certain
functions. Some warning and indicator lights illuminate when you switch on the
ignition and should go out with the engine running or while driving.
Some warning and indicator lights are accompanied by acoustic signals.
Symbol Meaning » See
Handbrake applied » page 75
Do not drive the vehicle!
Brake fluid level is too low or brake system is dis-
turbed.
Not drive the vehicle!
illuminates: Engine coolant temperature too high
or
flashes: Engine coolant system is disturbed.
Do not drive the vehicle!
Engine oil pressure is too low.
Do not drive the vehicle!
At least one vehicle door is open or not closed
properly.
Alternator is disturbed. » page 109
ABS is disturbed or failed. » page 75
Rear fog light switched on. » page 49
illuminates: Driving lights failed partially or com-
pletely.
» page 75
» page 106
» page 103
» page 21
» page 48
Symbol Meaning » See
Engine control or emission control system distur-
bed.
illuminates: Heating glow plugs of diesel engine
or
flashes: Engine control disturbed.
Engine control disturbed.
Steering disturbed. » page 84
Fuel tank nearly empty. » page 92
Airbag system disturbed. » page 40
Front passenger airbag turned off. » page 40
Ignoring illuminated warning lights may result in breaking down in traffic, accidents and serious injury.
■
■
■
the exhaust system come in contact with highly flammable materials under
the vehicle such as dry grass, fuel.
■
If necessary, turn on the hazard warning light system and place the warning
triangle on the side of the road to warn other road users.
Turn signal light left or right. » page 48
Warning light system switched on. » page 142
illuminates: Depress brake pedal! or
flashes: The lock button in the selector lever is
not engaged.
Main beam switched on or headlight flasher op-
erated.
WARNING
Never ignore illuminated warning lights.
Stop the vehicle as soon as it is possible and safe to do so.
Park the vehicle in a safe distance from moving traffic such that no parts of
A broken-down vehicle is a high accident risk to itself and other road users.
» page 139
Change
gear » page 70
Brake, stop and
park » page 75
» page 48
£
Instrument cluster
5
WARNING (Continued)
■
Before opening the engine compartment lid, switch off the engine and let it
cool down sufficiently.
■
The engine compartment of every vehicle is a dangerous area and may
cause serious injury » page 99.
NOTICE
Ignoring illuminated indicator lights may lead to vehicle damage.
Ð
6
Vehicle overview
Instruments
ä Introduction
This chapter contains information on the following subjects:
Overview of the instruments
Display 7
Service interval display 8
At low outside temperatures, the display on the instrument cluster may be slightly more time-delayed than at warm outside temperatures.
Additional information and warnings:
Warning and indicator lights » page 5
›
Display of the gears engaged (automatic gearbox) » page 70
›
Information on service intervals » booklet Service schedule
›
WARNING
Driver inattention can lead to accidents and injuries.
■
Never press the buttons in the instrument cluster to operate while driving.
Overview of the instruments
Fig. 2
Instrument cluster on the instrument panel
First read and observe the introductory information and safety warnings on page 7.
ä
Explanation of the instruments » fig. 2:
1
Revolutions counter (revolutions x 1000 per minute of the running engine).
The start of the red zone in the revolutions counter indicates the maximum
7
Ð
permissible engine speed for all gears for an engine which has been run in
and is operating at normal temperature. Before reaching the red zone, shift
up to the next higher gear, select the selector lever position D, or take your
foot off the accelerator pedal » .
2
Display » page 7.
3
Speedometer.
4
Adjust button for the clock.
Press the button
›
To advance the setting, press the
›
fast forward.
Press the button again to complete setting the clock.
›
5
Reset button for the display of the daily trip counter (trip).
Press the
›
to select the hour or minute display.
0.0 / SET
button to set to zero.
0.0 / SET
button 5. Press and hold to
NOTICE
To prevent engine damage, the pointer of the revolutions counter may enter
the red zone of the scale only for a short time.
Shifting to a higher gear as early as possible are ways to minimise fuel consumption and to reduce operating noise levels.
The fuel gauge is located in the lower section of the display 2.
Display
First read and observe the introductory information and safety warn-
on page 7.
ings
ä
The display of the instrument cluster 2 » fig. 2 may show various information,
depending on the vehicle equipment:
Mileage (kilometre) indicators.
›
Time.
›
Ð
£
Instrument cluster
7
Outside temperature.
›
Selector lever positions » page 70.
›
Multi-function display (MFD) » page 10.
›
Service interval display » page 8.
›
Mileage (kilometre) indicators
The odometer registers the total distance travelled of the vehicle.
The trip counter (trip) shows the miles (kilometres), which were driven after the
last reset of the trip counter. The last digit indicates 1/10 miles (100 metres).
Outside temperature display
At outside temperatures colder than +4 °C (+39 °F), a “snow flake symbol” (black
ice warning) also appears on the outside temperature display. This symbol flashes
initially and then stays lit until the outside temperature increases above +6 °C
(+43 °F) »
If the vehicle is stationary (or driven at a very low speed), the temperature indicated may be slightly higher than the actual outside temperature because of heat
radiated by the engine.
The measurement range is from -40 °C (-40 °F) to +50 °C (122 °F).
Selector lever positions
The set selector lever position is shown both at the side of the selector lever and
on the display on the instrument cluster. In the positions D and S and in Tiptronic,
the display may show the current gear.
.
WARNING
Ignoring illuminated warning lights may result in breaking down in traffic, accidents and serious injury.
■
Never ignore illuminated warning lights.
■
Stop the vehicle as soon as it is possible and safe to do so.
■
A broken-down vehicle is a high accident risk to itself and other road users.
If necessary, turn on the hazard warning light system and place the warning
triangle on the side of the road to warn other road users.
■
Park the vehicle in a safe distance from moving traffic such that no parts of
the exhaust system come in contact with highly flammable materials under
the vehicle such as dry grass, fuel.
WARNING
Roads and bridges may be icy at temperatures above freezing.
■
Ice may be present at temperatures above +4 °C (+39 °F), even if no “ice
crystal symbol” is displayed as a warning of black ice.
■
Never rely only on the outside temperature display!
NOTICE
Ignoring illuminated indicator lights may lead to vehicle damage.
Service interval display
First read and observe the introductory information and safety warnings
ä
The service event is shown in the instrument cluster display 2 » fig. 2 » page 7.
Service appointments at ŠKODA are distinguished between events with engine oil
change, such as interval service, and events without engine oil change, such as
inspection service. The service interval display only tells you the service appointments, which include an engine oil change. All other service appointments, such
as the next due inspection service or brake fluid change are indicated on the
sticker on the door frame of the vehicle or in the service schedule.
For vehicles with time- or mileage-dependent service, fixed service intervals are
specified.
Service reminder
If a service is due soon, a service reminder appears when switching on the ignition.
In the instrument cluster display a wrench symbol , and a miles display appear.
The stated mileage is the maximum number of miles that can be driven until the
service appointment is due. The display will change after a few seconds. A clock
symbol and the number of days until the due service appointment will appear.
Service event
When a service is due, an acoustic signal sounds and the flashing wrench symbol
appears for a few seconds when you switch on the ignition.
Retrieving service message
The current service message can be checked with the ignition switched on, the
engine switched off and the vehicle stationary:
on page 7.
Ð
£
8
Vehicle overview
Press the button in the instrument cluster repeatedly until the wrench sym-
›
bol appears.
An overdue service is indicated by a minus sign in front of the mileage or number-
of-days indication.
Resetting service interval display
If the service was not carried out by a ŠKODA partner, the display can be reset as
follows:
Switch off the ignition.
›
Press and hold the
›
Switch the ignition on again.
›
Release the
›
onds.
Do not reset the service display between service intervals, as this will result in in-
correct displays.
The service message will extinguish after a few seconds with the engine
running.
0.0 / SET
button.
0.0 / SET
button and press the button within approx. 20 sec-
Ð
Instrument cluster
9
ŠKODA information system
ä Introduction
This chapter contains information on the following subjects:
Overview of the multi-function display (MFD)
MFD menu (multi-function display) 10
Operating the menus in the instrument cluster 11
With the ignition switched on, various driving and consumption data from the
multi-function display (MFD) can be shown on the display.
A specialist garage may program or modify additional functions depending on the
vehicle equipment. ŠKODA recommends a ŠKODA partner for this purpose.
The multi-function display (MFD) is switched by using the buttons on the windscreen wiper lever.
WARNING
Driver inattention can lead to accidents and injuries.
Overview of the multi-function display (MFD)
First read and observe the introductory information and safety warn-
on page 10.
ings
ä
■
Driving time
■
Current fuel consumption
■
Average fuel consumption
■
Range
■
Distance travelled
■
Average speed
■
Digital speedometer
■
Speed warning
■
Outside temperature
MFD menu (multi-function display)
First read and observe the introductory information and safety warnings on page 10.
ä
The multi-function display (MFD) is equipped with two automatic memories:
1 – Single-trip memory and 2 - Total-distance-driven memory. The number of the
10
memory currently shown appears on the top right of the centre display.
To change between the two memories, press the
A
» fig. 3 » page 11 button while the ignition is switched on and memory 1 or
2 is displayed.
The memory collects driving and fuel consumption data
from the time the ignition is switched on until it is switch-
Single-trip
1
memory.
Ð
Total-distance-
2
driven memory.
Possible indications
Menu Function
Driving time Driving time in hours (h) and minutes (min) that has
Current fuel consumption
Average fuel con-
Ð
sumption
ed off.
The memory is cleared automatically after the driving time
is interrupted for more than two hours. If the drive continues within two hours after the ignition was switched off,
the new data will be added.
The memory collects the driving data of any number of single drives, depending on the model of the instrument cluster up to a total of 19 hours and 59 minutes or 99 hours
and 59 minutes driving time or 1999.9 miles (kilometres) or
9999 miles (km) distance travelled. If any of these maximum values is passed, the memory will automatically clear
and start again from 0.
elapsed after the ignition has been switched on.
The current fuel consumption is indicated while driving in
mpg (l/100 km) or with the engine running and the vehicle
stopped in gallons per hour (litres per hour).
The average fuel consumption in mpg (l/100 km) will appear after the ignition is switched on only after a distance
of about 328 feet (100 metres). Until then, dashes are displayed. The displayed value is updated approx. every five
seconds.
OK/RESET
£
10
Vehicle overview
Menu Function
Range Approximate driving distance in miles (km) that can be driv-
Distance travelled The distance travelled in miles (km) after the ignition has
Average speed The average speed is displayed after the ignition has been
Warning at --- mph When exceeding a stored speed from approx. 18 mph
Outside temperature
en with the existing fuel amount in the tank using the
same driving style. This is calculated based on the current
fuel consumption among other factors.
been switched on.
switched on only after a distance of about 328 feet (100
metres). Until then, dashes are displayed. The displayed
value is updated approx. every five seconds.
(30 km/h), an acoustic and possibly a visual warning are issued.
Display of the current outdoor temperature in °C or °F.
Operating the menus in the instrument cluster
Fig. 3
Multi-functional indicator: control elements
First read and observe the introductory information and safety warnings on page 10.
ä
Selecting memory 1 or 2
Switch on the ignition.
›
Press the
›
ory.
OK/RESET
button repeatedly A » fig. 3 until you see the desired mem-
Manually clearing memory 1 or 2
Switch on the ignition.
›
Select the memory you wish to clear.
›
Press and hold the
›
Display of driving and fuel consumption data
Switch on the ignition.
›
Select memory.
›
Push the rocker up or down repeatedly
›
Storing a speed for the speed warning
Select speed warning.
›
Press the
›
ing.
If necessary, within approx. five seconds set the desired speed with the rocker
›
B
. Then press again the
saved and the alarm is activated.
To deactivate, press the
›
Ð
When the vehicle is stationary (or driven at a very low speed) the temperature indicated may be slightly higher than the actual outside temperature
because of heat radiated by the engine.
OK/RESET
button for approx. two seconds A.
B
until the desired value is displayed.
OK/RESET
button A to save the current speed and activate the warn-
OK/RESET
button or wait a few seconds. The speed is
OK/RESET
button. The stored speed is deleted.
Ð
Instrument cluster
11
Before driving
Before you start
Driving tips
ä Introduction
This chapter contains information on the following subjects:
Driving preparations and driving safety
Motoring abroad 13
Driving through water on roads
Depending on where the vehicle is used, it may be recommended having an engine undershield installed. An engine undershield can reduce the risk of damage
to the vehicle underside and the engine oil pan, for example, when driving over
curbs, driveways or on unpaved roads. ŠKODA recommends a ŠKODA partner for
the installation.
Additional information and warnings:
Sitting properly and safely » page 27
›
Transporting » page 56
›
Starting, shifting gears, parking » page 66
›
Driving in an environmentally conscious manner » page 82
›
Consumer information » page 137
›
WARNING
Driving under the influence of alcohol, drugs, medicines, and anaesthetics can
cause serious accidents and fatal injuries.
■
Alcohol, drugs, medicines and anaesthetics may affect perception, reaction
times and driving safety significantly, resulting in possible loss of control over
the vehicle.
Driving preparations and driving safety
First read and observe the introductory information and safety warnings on page 12.
ä
For your own safety, the safety of all passengers and other road users, the following points must be observed before and during each drive » :
Check the proper function of lighting and turn signal lights.
›
Check tyre pressure » page 122 and fuel level » page 92.
›
Provide for clear and good visibility through all windows.
›
Secure objects and luggage in the stowage compartments and in the boot.
›
The pedals must be operable at any time without hindrance.
›
Children in the car must be secured with a restraint system that is suitable for
›
12
their body weight and body size » page 44.
Adjust the front seat, head restraint and mirrors correctly according to your
›
13
body height » page 27.
Wear shoes that give your feet good support for the operation of the pedals.
›
The floor mat in the footwell on the driver’s side must leave the pedal area free
›
and be securely fastened.
Assume a correct seated position before starting to drive and maintain it while
›
driving. This also applies to all passengers » page 27.
Fasten the seat belt properly before driving and leave it on while driving. This
›
also applies to all passengers » page 34.
Only carry as many people as there are seats and seat belts.
›
Never drive when your driving ability is impaired, for example, by medication, al-
›
cohol or drugs.
Never let yourself be distracted from the road, for example, by adjustments and
›
by selecting menus, by passengers or phone calls.
Always adjust your speed and driving style to the visibility, weather, road and
›
traffic conditions.
Observe traffic rules and specified speeds.
›
Take regular breaks on long trips – at least every two hours.
›
Secure animals in the vehicle with a system that is appropriate for their weight
›
and size.
Ð
WARNING
Always follow the current traffic laws and speed limits and drive proactively.
The correct assessment of the driving situation can mean the difference between the safe reach of the destination and an accident with serious injuries.
£
12
Before driving
Regular service on the vehicle is not only for the maintenance of the vehi-
cle, but also contributes to the operational and road safety. Therefore, have
service be carried out in accordance with the requirements of the service schedule. Under difficult operating conditions, some work may become necessary already before the due date of the next service. Difficult conditions are, for example, frequent stop-and-go traffic, driving in areas with heavy dust. For more information, consult your ŠKODA partner or specialist garage.
Motoring abroad
First read and observe the introductory information and safety warnings on page 12.
ä
In some countries there are specific safety standards and emissions-related regulations, which differ from the design of the vehicle. ŠKODA recommends before a
trip abroad, to gather information from a ŠKODA partner on legal provisions and
on the following points in your destination country:
Must the vehicle be technically prepared for the trip abroad, such as masking
›
the headlights?
Are the necessary tools, diagnostic equipment and spare parts for service and
›
repair available?
Is a ŠKODA partner available in the destination country?
›
For petrol engine models: Is lead-free petrol with sufficient octane available?
›
For diesel engine models: If low-sulphur diesel fuel available?
›
Are the correct engine oil » page 103 and other fluids as specified by ŠKODA
›
available in the destination country?
Are special tyres required for driving in the destination country?
›
NOTICE
ŠKODA is not responsible for damage to the vehicle arising from poor quality
fuel, poor service or lack of original parts availability.
Determine the depth of the water when driving through bodies of water. The
›
water may only be enough to reach the lower edge of the body » .
Do not travel faster than walking pace.
›
Never stop, reverse or switch off the engine in water.
›
Oncoming vehicles generate waves that can raise the water level for your vehi-
›
cle so much that it is not safe to cross the water.
Ð
WARNING
After driving through water, mud, sludge, etc. the braking effect may be delayed due to wet and, in winter, icy brake discs and brake pads, extending the
stopping distance.
■
“Dry and free the brakes from ice” by careful braking actions. In doing so, do
not endanger other motorists or ignore statutory provisions.
■
Avoid abrupt and sudden braking immediately after water crossings.
NOTICE
■
When driving through bodies of water, parts of the vehicle such as the en-
gine, gearbox, chassis or electrics can be severely damaged.
■
Never drive through salt water, as salt can cause corrosion. Rinse any vehicle parts that have come in contact with salt water immediately with fresh
water.
Ð
Ð
Driving through water on roads
First read and observe the introductory information and safety warnings on page 12.
ä
To avoid damage to the vehicle when driving through flooded roads, for example,
note the following:
Before you start
13
Technical data
ä Introduction
This chapter contains information on the following subjects:
Vehicle identification data
Engine data 15
Dimensions 15
Performance 15
The engine that a vehicle is equipped with is indicated in the vehicle data sticker
in the service schedule or the official registration documents.
The information in the official registration documents always has priority. All information in this Owner’s Manual is for the basic model. By optional equipment or
different model versions and for special vehicles and vehicles for other countries,
the indicated values may differ.
Additional information and warnings:
Transporting » page 56
›
Driving in an environmentally conscious manner » page 82
›
Fuel » page 96
›
Engine oil » page 103
›
Engine coolant » page 106
›
Wheels and tires » page 122
›
Consumer information » page 137
›
WARNING
Failure to comply with or exceed the specified values for weight, payload, dimensions and maximum speed may lead to accidents and serious injuries.
Vehicle identification data
14
Fig. 4 Vehicle data sticker / Type plate
First read and observe the introductory information and safety warnings
ä
Vehicle identification number
The vehicle identification number can be read from the outside through a viewing
window in the windscreen. The viewing window is on the side at the bottom of
the windscreen. In addition, the vehicle identification number is punched in at the
right water drainage channel. The water drainage channel is located between the
suspension strut dome and the fender. To get to the vehicle identification number, open the bonnet » page 99.
Vehicle data sticker
The vehicle data sticker » fig. 4 - is stuck in the spare wheel well in the boot
and contains the following data:
1
Vehicle identification number (chassis number)
2
Ð
Vehicle type, engine power, transmission
3
Engine and gearbox code, paint number, interior equipment number. In the
example, the engine code is “CLNA”
4
Optional equipment, PR numbers
These vehicle data are also indicated in the service schedule.
Type plate
The type plate » fig. 4 - can be seen at the bottom of the door frame after
opening the front passenger door. Vehicles for certain export countries do not
have a type plate.
on page 14.
£
14
Before driving
Besides the vehicle identification number (chassis number) and the engine code,
the type plate contains the following data:
5
Permissible gross weight
6
Permissible front axle load
7
Permitted rear axle load
Engine data
First read and observe the introductory information and safety warnings on page 14.
ä
For approval or tax related reasons, the power and performance data of some engines may differ from the specifications in other countries.
Petrol engines
Engine power
(kW per rpm)
77/5250 153/3800 4/1598
Diesel engine
Engine power
(kW per rpm)
77/4400 250/1500 - 2500 4/1598
Max. torque (Nm at rpm)
Max. torque (Nm at rpm)
Number of cylinders /
Displacement cm
Number of cylinders /
Displacement cm
3
3
Dimensions
First read and observe the introductory information and safety warnings on page 14.
ä
Length 4,386 mm
Width 1,699 mm
Height (unladen) 1,466 mm
Wheel base 2,552 mm
Minimum turning circle diameter
Track gaugea) front 1,460 mm
a)
10.6 m
Track gaugea) rear 1,498 mm
Ground clearance at permissible gross weight
a)
Depending on the rim and tyre size, small deviations are possible.
b)
Value at permissible gross weight; the specified value may differ depending on the equipment.
Ð
b)
129 - 151 mm
NOTICE
■
Drive cautiously onto parking lots with high-curb mounts or solid boundaries. Those objects protruding from the ground may damage the bumper and
other vehicle parts when parking or leaving.
■
Drive cautiously over driveways, ramps, curbs and other objects. Deep-seated vehicle parts such as bumpers, spoilers and parts of the chassis, engine or
exhaust system can be damaged when driving over these objects.
Performance
First read and observe the introductory information and safety warnings on page 14.
ä
For approval or tax related reasons, the power and performance data of some engines may differ from the specifications in other countries.
Petrol engines
Ð
Engine power Transmission Maximum speed
77 kW
Diesel engine
Engine power Transmission Maximum speed
77 kW SG5 186 km/h
The performance figures were determined without performance-reducing
equipment such as mud flaps.
SG5 188 km/h
AG6 183 km/h
Ð
Ð
Before you start
15
Opening and closing
Vehicle key set
Introduction
ä
This chapter contains information on the following subjects:
Vehicle key
Indicator light in the vehicle key 17
Replacing the battery 18
Synchronising the vehicle key 18
Additional information and warnings:
Central locking system and closing system » page 19
›
Starting and stopping the engine » page 66
›
Consumer information » page 137
›
Emergency closing or opening » page 144
›
DANGER
If batteries with a diameter of 20 mm or other lithium batteries are swallowed, serious or even fatal injuries may result in a very short time.
■
Always keep the vehicle key and key chains with batteries, spare batteries,
button cells and other batteries that are larger than 20 mm out of reach of
children.
■
Get medical attention immediately if you assume that a battery has been
swallowed.
WARNING
Careless or unsupervised use of the vehicle keys can cause accidents and serious injuries.
■
Always take along all vehicle keys when leaving the vehicle. Children or unauthorized persons can lock the doors and boot lid, start the engine, switch
on the ignition and thus operated electrical equipment, such as power windows.
WARNING (Continued)
■
Never allow children or people requiring help alone in the vehicle. In an
emergency, they are unable to leave the vehicle alone or to help themselves.
For example, depending on the season, very high or low temperatures may
develop in a closed vehicle, causing serious injuries and illness or death, especially in young children.
■
Never remove the vehicle key from the ignition while the vehicle is in motion. The steering lock can engage and the vehicle can no longer be steered.
16
Vehicle key
Fig. 5
Vehicle key
First read and observe the introductory information and safety warnings on page 16.
ä
Vehicle key
With the vehicle key, the vehicle can be remotely locked and unlocked.
The transmitter with the battery is housed in the vehicle key. The receiver is loca-
ted in the interior of the vehicle. The effective range of the vehicle key is a few
metres around the vehicle when the battery is full.
When it is not possible to open or close the vehicle with the vehicle key, the vehicle key must be re-synchronised » page 18 or the battery in the vehicle key must
be replaced » page 18.
Multiple vehicle keys may be used.
Flipping the key bit out or in
By pressing the button
To flip in the key bit, press the button and simultaneously push the key back until
it clicks into place.
A
» fig. 5, the key bit unlocks and flips out.
Ð
£
16
Before driving
Replacement key
To obtain a replacement key or additional vehicle keys, the chassis number of the
vehicle is necessary.
Every new vehicle key must contain a microchip that is coded with the data of the
vehicle’s electronic immobiliser. A vehicle key does not work if it contains no microchip, or contains a microchip that is not coded. This also applies to vehicle keys
that are cut correctly.
New vehicle keys or replacement keys are available from ŠKODA partners or professional and authorized locksmiths who are qualified to produce these vehicle
keys.
New vehicle keys and replacement keys must be programmed before
use » page 18.
NOTICE
Each vehicle key contains electronic components. Protect vehicle keys from
damage, moisture and strong shocks.
Press the buttons in the vehicle key only if the corresponding feature is actually needed. An unnecessary push of a button may inadvertently unlock
the vehicle. This applies even if you think that you are out of range.
The function of the vehicle key may be temporarily affected by interference
from nearby transmitters operating in the same frequency range, for exam-
ple, by radio equipment or a mobile phone.
Obstacles between the vehicle and the vehicle key, bad weather conditions
and weak batteries reduce the radio range.
If the buttons in the vehicle key » fig. 5 » page 16 or one of the central lock-
ing buttons » page 19 are pushed several times in a row within a short
time, the central locking system will temporarily shut down to protect against
overload. The vehicle is then unlocked. Lock the vehicle if necessary.
Indicator light in the vehicle key
Fig. 6
Indicator light in the vehicle key
First read and observe the introductory information and safety warnings on page 16.
ä
When a button in the vehicle key is pressed shortly, the indicator light (arrow) » fig. 6 will flash once briefly. By prolonged pressing of a button, it flashes
several times, such as during convenience opening.
If the indicator light in the vehicle key fails to light up when a button is pressed,
the battery in the vehicle key must be replaced » page 18.
Ð
Ð
Opening and closing
17
Replacing the battery
Fig. 7 Vehicle key: open the battery compartment cover / remove the battery
First read and observe the introductory information and safety warnings on page 16.
ä
ŠKODA recommends having the battery replaced by a specialist garage.
The battery is located on the rear of the vehicle key under a cover.
When replacing the battery, pay attention to the correct polarity and use the
same type of battery »
Replacing the battery
Flip out the key bit of the vehicle key » page 16.
›
Pry off the battery cover
›
the points of the arrows 1 and remove » .
Press down the battery in the direction of the arrow 2 and remove it from the
›
key.
Insert the new battery and push it into the battery compartment » .
›
Place the battery cover on the key and press it down until it clicks into place.
›
.
B
» fig. 7 with your thumb or with a flat screwdriver at
NOTICE
■
An improperly performed battery replacement could damage the vehicle key.
■
Improper batteries may cause damage to the vehicle key. Discharged batter-
ies may be replaced only with new batteries of the same voltage, same size
and specification.
■
When installing the battery, pay attention to the correct polarity.
Dispose of discharged batteries in accordance with environmental regulations.
Synchronising the vehicle key
First read and observe the introductory information and safety warnings on page 16.
ä
If the button is pressed frequently outside the effective range, it may no longer
be possible to lock or unlock the vehicle with the vehicle key. In this case, the vehicle key must be re-synchronised as follows:
Flip out the key bit of the vehicle key » page 16.
›
Press the
›
when doing so.
Unlock the vehicle with the key bit flipped out within one minute.
›
Switch on the ignition with the vehicle key. The synchronisation is now com-
›
plete.
button in the vehicle key. Stand immediately close to the vehicle
Ð
Ð
18
Before driving
Central locking and closing system
ä Introduction
This chapter contains information on the following subjects:
Description of the central locking system
Unlocking and locking the vehicle from the outside 20
Unlocking and locking the vehicle from the inside 20
The central locking system only works properly if all the doors and the boot lid are
completely closed. The vehicle can not be locked with the vehicle key when the
driver’s door is open.
Longer times of an unlocked vehicle (for example, in your own garage) can cause
the vehicle battery to discharge so that the engine can no longer be started.
Additional information and warnings:
Vehicle key set » page 16
›
Doors » page 21
›
Boot lid » page 23
›
Power windows » page 25
›
Emergency closing or opening » page 144
›
WARNING
Improper use of the central locking system can cause serious injury.
■
The central locking system locks all doors. Locking a vehicle from the inside
may prevent undesired opening of doors and intrusion by unauthorized persons. In an emergency or in case of an accident, however, locked doors make
it difficult for helpers to access the passenger compartment to help people.
■
Never allow children or people requiring help alone in the vehicle. With the
central locking button, all doors can be locked from the inside. This may result
in trapping yourself in the vehicle. Trapped persons can be exposed to very
high or very low temperatures.
■
Depending on the season, very high or low temperatures may develop in a
closed vehicle, causing serious injuries and illness or death especially in young
children.
■
Never leave people in a locked vehicle. In an emergency, these persons are
unable to leave the vehicle alone or to help themselves.
Description of the central locking system
First read and observe the introductory information and safety warnings on page 19.
ä
The central locking system allows you to centrally lock and unlock all doors and
the boot lid:
19
from the outside using the vehicle key,
›
from the inside using the central locking button » page 20.
›
Particular features of the central locking system can be enabled or disabled by a
specialist garage.
The doors and the boot lid can be unlocked or locked manually if the vehicle key
fails.
Locking the vehicle after the airbags are deployed
In the event that the airbags are deployed in an accident, the entire vehicle is unlocked. Depending on the degree of damage, the vehicle can be locked after the
accident as follows.
Function Action
Locking the vehicle from
the inside:
Locking the vehicle from
the outside:
Auto lock feature
All the doors and the boot lid are locked automatically once the car reaches a
speed of about 15 km/h.
If the ignition key is withdrawn, the car is then automatically unlocked again.
Ð
– Switch the ignition off and on again.
– Press the central locking button .
– Switch the ignition off and on again.
Or: Remove the vehicle key from the ignition lock.
– Open a vehicle door once.
– Lock the vehicle using the vehicle key.
Ð
Opening and closing
19
Unlocking and locking the vehicle from the outside
Fig. 8 Key without remote control / Remote control key
First read and observe the introductory information and safety warnings
ä
Function Action with the buttons
Unlocking
the vehicle
Locking
the vehicle
Unlocking
the boot
lid
The remote control key locks and unlocks the vehicle only if the batteries have
sufficient power and the vehicle key is in the range of a few metres around the
vehicle.
When locking the vehicle, all turn signal lights will flash once for confirmation.
›
When unlocking the vehicle, all turn signal lights will flash twice for confirma-
›
tion.
If the turn signal lights do not flash for confirmation, at least one of the doors or
the boot lid or bonnet is not locked.
on page 19.
in the vehicle key » fig. 8
-
Press the button.
Press and hold for convenience opening.
Press the button. Press
and hold for convenience
closing.
Press the button. Insert vehicle key into lock cylinder of
Action with the vehicle key in the lock
cylinder or with a mechanical vehicle
key » fig. 8 -
Insert vehicle key into lock cylinder of
the driver’s door and turn clockwise.
Turn and hold for convenience opening.
Insert vehicle key into lock cylinder of
the driver’s door and turn counter-
clockwise. Turn and hold for convenience closing.
the boot lid and turn clockwise.
The vehicle can not be locked with the vehicle key when the driver’s door is open.
If the vehicle is unlocked and no door or the boot lid is opened, the vehicle is
locked again automatically after a few seconds. This function is intended to prevent the vehicle from being unlocked unintentionally.
Convenience opening and closing
See power windows – features » page 25.
›
Unlocking and locking the vehicle from the inside
Fig. 9
In the driver’s door: central locking button
First read and observe the introductory information and safety warnings
ä
Press the button » fig. 9:
The central locking button works both with the ignition switched on and off.
If the vehicle is locked with the central locking button, then:
Opening the doors and the boot lid from the outside is not possible, for exam-
›
ple, when stopping at traffic lights.
Doors can be unlocked and opened from the inside by pulling the door opening
›
lever. If necessary, the door opening lever must be pulled repeatedly.
An open driver’s door is not included in the locking operation. This prevents that
›
the driver locks himself out.
on page 19.
Unlocking the vehicle
Locking the vehicle
Ð
Ð
20
Before driving
Doors
ä Introduction
This chapter contains information on the following subjects:
Warning light
Child safety lock 21
Additional information and warnings:
Vehicle key set » page 16
›
Central locking system and closing system » page 19
›
Emergency closing or opening » page 144
›
WARNING
An improperly closed door can open suddenly while driving, causing serious injuries.
■
Immediately stop and close the door.
■
When closing make sure that the door locks fully into place. The closed door
must be flush with the surrounding body parts.
■
Open or close doors only when no one is within the swivelling range.
WARNING
A door held open with the door strap may close automatically in strong wind
conditions and on slopes, causing injuries.
■
Always hold the door handle when opening and closing any door.
Warning light
First read and observe the introductory information and safety warnings on page 21.
ä
Illumi-
nates
Possible cause Remedy
At least one vehicle
door is open or not
closed properly.
Do not drive the vehicle!
Open the corresponding vehicle door and
close it again.
When switching on the ignition, some warning and indicator lights illuminate
briefly as a function test. They will extinguish after a few seconds.
If a door is open or not closed properly, the warning light illuminates in the instrument cluster.
The warning light is visible even when the ignition is switched off.
21
Child safety lock
Fig. 10 Child safety lock: in the rear left door / in the rear right door
First read and observe the introductory information and safety warnings
ä
The child safety lock prevents opening the rear doors from inside, so, for example,
children can not accidentally open a door while the car is in motion. While the
Ð
child safety lock is switched on, the door can be opened only from the outside.
Switching the child safety lock on or off
Unlock the vehicle and open the appropriate rear door.
›
Flip out the key bit from the vehicle key.
›
Use the key bit to move the slot to the desired position.
›
Position of the slot » fig. 10:
A
Child safety lock off.
B
Child safety lock on.
on page 21.
Ð
£
Opening and closing
21
WARNING
When the child safety lock is switched on, the respective door can not be
opened from the inside.
■
Never leave children or persons requiring help inside the vehicle when the
doors are locked. This may cause these people to get trapped in the vehicle. In
an emergency, they would not be able to leave the vehicle alone or to help
themselves. Trapped persons can be exposed to very high or very low temperatures.
■
Depending on the season, very high or low temperatures may develop in a
closed vehicle, causing serious injuries and illness or death especially in young
children.
Ð
22
Before driving
Boot lid
ä Introduction
This chapter contains information on the following subjects:
Opening the boot lid
Closing the boot lid 24
Additional information and warnings:
Central locking system » page 19
›
Transporting » page 56
›
WARNING
Improper and unsupervised unlocking, opening or closing the boot lid can
cause accidents and serious injuries.
■
Open or close the boot lid only when no one is within the swivelling range.
■
After closing the boot lid, check that it is properly closed and locked so that
it can not open automatically while driving. The closed boot lid must be flush
with the surrounding body parts.
■
Always keep the boot lid closed while driving to prevent toxic exhaust gases
from entering the interior.
■
Never open the boot lid when it is loaded with cargo, for example, on a luggage rack. Likewise, the boot lid may not open if it is loaded with objects, such
as bicycles. An open boot lid may lower independently by the additional
weight. Where appropriate, support the boot lid or remove the load beforehand.
■
Close and lock the boot lid and all doors when the vehicle is not used. Make
sure that no one is left in the vehicle.
■
Never let children play in and around the vehicle unattended, especially
when the boot lid is open. Children may climb into the boot, close the boot lid
and thus lock themselves. Depending on the season, very high or low temperatures may develop in a closed vehicle, causing serious injuries and illness or
death especially in young children.
■
Never allow children or people requiring help alone in the vehicle. They may
lock the vehicle with the vehicle key or the central locking button, thereby
locking themselves.
NOTICE
Before opening the boot lid, check that there is sufficient space for opening
and closing the boot lid, for example, in garages.
23
Opening the boot lid
Fig. 11 Vehicle key with unlocking button for the boot lid / Opening the boot
lid from the outside
First read and observe the introductory information and safety warnings on page 23.
ä
If, for example, bicycles are mounted on a rack on the boot lid, it may not be possible to open the boot lid »
open boot lid.
Unlocking with the vehicle key
Press and hold the
and springs open slightly.
Unlocking via the button in the driver’s door
Pull the
springs open slightly.
The button in the driver’s door also works with the ignition switched off.
Unlocking via the lock cylinder in the boot lid
Insert the vehicle key into the lock cylinder of the boot lid and turn clockwise
until the boot lid unlocks and springs open slightly.
button in the driver’s door upwards, until the boot lid unlocks and
. Remove the object from the rack and support the
button in the vehicle key » fig. 11 until the boot lid unlocks
Ð
1
,
£
Opening and closing
23
Opening the boot lid
Lift and fully open the unlocked boot lid 2 » fig. 11 » page 23, until the boot lid is
held at the stop in a holding position.
WARNING
Improper or unsupervised unlocking or opening the boot lid can cause serious
injury.
■
If a luggage rack including cargo is mounted on the boot lid, it may not always be possible to recognise that a boot lid is unlocked. An unlocked boot lid
may open suddenly while driving.
WARNING
Improper or unsupervised closing of the boot lid can cause serious injury.
■
Never leave your vehicle unattended or let children play in and around the
vehicle, especially when the boot lid is open. Children may climb into the boot,
close the boot lid and thus lock themselves. A closed vehicle can extremely
heat up or cool down depending on the season, causing serious injury, illness
or even death.
Ð
Before closing the boot lid, check that the vehicle key is not in the boot.
Closing the boot lid
Fig. 12
Open boot lid: recesses for closing
First read and observe the introductory information and safety warnings on page 23.
ä
Closing the boot lid
Reach into one of the recesses in the inner panelling of the boot lid » fig. 12.
›
Pull down and close the boot lid.
›
Check, by pulling on the boot lid, that it is securely locked.
›
Locking the boot lid
The vehicle will be locked again automatically if you do not open one of the doors
or the boot lid a few seconds after unlocking the car. This function prevents the
vehicle from remaining unlocked if the unlocking button is pressed by mistake.
The boot lid can only be locked when it is properly closed and engaged.
The boot lid is also locked by the central locking system.
›
If the boot lid of a locked vehicle is unlocked using the
›
key, it will lock again approximately 20 seconds after it is closed.
24
Before driving
button in the vehicle
When the boot lid is in the holding position, a greater force may be necessary to close the boot lid.
Ð
Power windows
Electrically opening or closing the windows
ä Introduction
This chapter contains information on the following subjects:
Electrically opening or closing the windows
Force limiter of the power windows 26
Additional information and warnings:
Central locking system and closing system » page 19
›
Maintaining and cleaning the vehicle exterior » page 112
›
WARNING
Careless or unsupervised use of the power windows can cause serious injuries.
■
Open or close the power windows only when no one is in the functional
range.
■
Never leave children or persons requiring help inside the vehicle when the
vehicle is locked. The windows may no longer open in an emergency.
■
Always take along all vehicle keys when leaving the vehicle. After switching
off the ignition, the windows can still be opened or closed briefly via the buttons as long as the driver’s or front passenger door is not opened.
■
When carrying children in the back seats, always disable the rear power windows with the safety button so that the windows can not be opened or
closed.
NOTICE
When the windows are open, sudden precipitation may drench the interior of
the vehicle, resulting in vehicle damage.
25
First read and observe the introductory information and safety warnings on page 25.
ä
Buttons in the driver’s door
Legend to fig. 13:
1
For the windows in the front doors
2
For the windows in the rear doors
3
Safety button
WARNING
Careless or unsupervised use of the power windows can cause serious injuries.
■
Open or close the power windows only when no one is in the functional
range.
■
Never leave children or persons requiring help inside the vehicle when the
vehicle is locked. The windows may no longer open in an emergency.
■
Always take along all vehicle keys when leaving the vehicle. After switching
Ð
off the ignition, the windows can still be opened or closed briefly via the buttons as long as the driver’s or front passenger door is not opened.
■
When carrying children in the back seats, always disable the rear power windows with the safety button so that the windows can not be opened or
closed.
Fig. 13
In the driver’s door: buttons for
the front and rear power windows
Ð
Opening and closing
25
Force limiter of the power windows
First read and observe the introductory information and safety warnings on page 25.
ä
The force limiter of the power windows can reduce the risk of crush injury when
closing a window » . If the automatic closing operation of a window is impaired
by stiffness or by an obstruction, the window will immediately open again.
Check why the window did not close.
›
Try again to close the window.
›
If, within 10 seconds since the first stopping and opening of the window, the
›
window is again prevented from closing by stiffness or by an obstruction, the
automatic closing operation will be suspended for about 10 seconds.
If the window still can not be closed by stiffness or by an obstruction, the win-
›
dow stops at the respective point. By pressing the button once again within
10 seconds, the window will close without any force limitation »
Closing a window without force limitation
Try to close again the window within approx. 10 seconds by pressing and hold-
›
ing the button. The force limiter will be disabled for a small functional range of
the closing operation!
If the closing operation takes longer than approx. 10 seconds, the force limiter
›
will be active again. The window will then stop again when it encounters stiffness or an obstruction.
If the window still can not be closed, consult a specialist garage.
›
.
WARNING
Closing of the power windows without force limitation can cause serious injuries.
■
Always close power windows with caution.
■
No one may be present within the functional range of the power windows,
especially when they are closed without force limitation.
■
The force limiter does not prevent fingers and other body parts from being
pressed against the window frame and getting injured.
Ð
26
Before driving
Sitting properly and safely
Adjusting the seat position
Introduction
ä
This chapter contains information on the following subjects:
Risk of a bad seated position
Correct seated position 28
Mechanical controls on the front seats 29
Adjusting the head restraint 30
Removing and installing a head restraint 30
Adjusting the steering wheel position 31
Centre armrest
Number of seats
The vehicle has a total of five seats: two seats in the front and three seats in the
back. Each seat is equipped with a seat belt.
Additional information and warnings:
Seat features » page 33
›
Seat belts » page 34
›
Airbag system » page 40
›
Child seats (optional) » page 44
›
WARNING
An incorrect seated position in the vehicle in the event of sudden driving and
braking manoeuvres, in a collision or accident, and when the airbags are deployed may increase the risk of serious or fatal injuries.
■
All passengers must assume the correct seated position before departure
and maintain it during travel. This also applies to the use of seat belts.
■
Never carry more people than the number of seats with seat belts in the ve-
hicle.
28
WARNING (Continued)
■
Children should always be secured in the vehicle with an approved and appropriate restraint system according to their size and
weight » page 44, » page 40.
■
Always keep your feet inside the footwell during the ride. Never, for example, put your feet on the seat or on the instrument panel and never stick them
out of the window. The airbag and the seat belt can otherwise develop no
protective effect but can increase the risk of injuries in an accident.
WARNING
Before all trips, always adjust the seat, the seat belt and the head restraint
properly and make sure that all passengers wear their seat belts correctly.
■
Slide the front passenger seat back as far as possible.
■
Adjust the driver’s seat such that at least 10 inches (25 cm) are between
31
your chest and the steering wheel centre. If this requirement can not be met
due to physical characteristics, be sure to consult a specialist garage about
making any special installations.
■
Never drive with the seat backrest excessively inclined backward. The further the seat backrest is inclined backward, the greater the risk of injuries due
to incorrect routing of the webbing of the seat belt and a bad seated position.
■
Never drive with the seat backrest inclined forward. A deploying front airbag
may slam the seat backrest to the rear, thereby injuring the passengers in the
rear seats.
■
Assume and maintain a seated position as far as possible from the steering
wheel and instrument panel.
■
Always sit upright with your back against the seat backrest in correctly adjusted front seats. Do not position any body part directly at or too close to the
installation positions of the airbags.
■
For rear seat passengers, the risk of serious injuries increases if they do not
sit upright, because the seat belts are not positioned correctly.
WARNING
Improper adjustment of the seats can cause accidents and serious injuries.
■
Adjust the seats only when the vehicle is stationary because the seats may
shift unexpectedly while driving, causing you to lose control of the vehicle. In
addition, a wrong seated position will be assumed during the adjustment.
£
Sitting properly and safely
27
WARNING (Continued)
■
Adjust the height, inclination and forward/back direction only when no one
is within the adjustment range of the seats.
■
The adjustment of the front seats must not be constrained by objects.
Risk of a bad seated position
First read and observe the introductory information and safety warnings on page 27.
ä
If the seat belts are not fastened or were not adjusted properly, the risk of serious or fatal injuries is increased. Seat belts offer their optimum protection only if
the webbing of the seat belts is properly routed. An incorrect seated position significantly impairs the protective effect of seat belts. Serious or even fatal injuries
can be the result. The risk of serious or fatal injuries is increased particularly
when a deployed airbag hits an occupant who has assumed a wrong seated position. The driver is responsible for all passengers, especially for children that are
carried in the vehicle.
The following list contains examples of which seated positions can be dangerous
for all occupants.
Whenever the vehicle is in motion:
Never stand in the vehicle.
›
Never stand on the seats.
›
Never knee on the seats.
›
Never incline the seat backrest excessively to the back.
›
Never lean against the instrument panel.
›
Never lie down on the rear seat bench.
›
Never only sit on the front area of the seat.
›
Never sit facing to the side.
›
Never lean out the window.
›
Never put your feet out of the window.
›
Never put your feet on the instrument panel.
›
Never put your feet on the seat cushion or seat backrest.
›
Never ride in the footwell.
›
Never sit on the front or rear armrest.
›
Never ride without seat belts on the seat.
›
Never climb into the boot.
›
WARNING
Any bad seated position in the vehicle increases the risk of serious or fatal injuries in the event of accidents and sudden driving and braking manoeuvres.
Ð
■
All passengers must assume the right seated position and be wearing a seat
belt properly.
■
By incorrect seated positions, failure to wear seat belts, or sitting too close
to the airbag, occupants expose themselves to life-threatening or fatal injuries, especially if the airbags deploy, hitting an occupant who has assumed a
bad seated position.
Correct seated position
Fig. 14
The correct driver’s distance from the steering wheel / Correct rout-
ing of the belt webbing and correct head restraint adjustment
First read and observe the introductory information and safety warnings
ä
The following explains the correct seated positions for the driver and passengers.
Individuals who can not assume the correct seated position because of their
physical characteristics should check with a specialist garage about possible special installations. Only with the correct seated position can the optimal protective
effect of seat belts and airbags be obtained. ŠKODA recommends a ŠKODA partner for this purpose.
For your safety and to reduce injuries in the event of a sudden braking manoeuvre or accident, ŠKODA recommends the following seated positions:
on page 27.
Ð
£
28
Before driving
Loading...