Škoda Fabia 2013 Owner's Manual

SIMPLY CLEVER

ŠKODA Fabia Owner's Manual

Layout of this Owner's Manual (explanations)

This Owner's Manual has been systematically designed to make it easy for you to search for and obtain the information you require.

Chapters, table of contents and subject index

The text of the Owner's manual is divided into relatively short sections which are combined into easy-to-read chapters. The chapter you are reading at any particular moment is always specified on the bottom right of the page.

The Table of contents is arranged according to the chapters and the detailed Sub- ject index at the end of the Owner's Manual helps you to rapidly find the information you are looking for.

Direction indications

All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of travel of the vehicle.

Units of measurement

All values are expressed in metric units.

Explanation of symbols

 Denotes a reference to a section with important information and safety

advice in a chapter.

 Denotes the end of a section.

 Denotes the continuation of a section on the next page.

 Indicates situations where the vehicle must be stopped as soon as possi-

ble.

® Denotes a registered trademark.

 Denotes the display in the MAXI DOT display.  Denotes the display in the segment display.

Display

The display in the segment display will be used in this Owner's Manual to represent the display unless otherwise specified.

Notes

WARNING

The most important notes are marked with the heading WARNING. These WARNING notes draw your attention to a serious risk of accident or injury.

CAUTION

A Caution note draws your attention to the possibility of damage to your vehicle (e.g. damage to gearbox), or points out general risks of an accident.

For the sake of the environment

An Environmental note draws your attention to environmental protection aspects. This is where you will, for example, find tips aimed at reducing your fuel consumption.

Note

A normal Note draws your attention to important information about the operation of your vehicle.

Documentation of vehicle handover

Date of delivery/initial registrationa) (VIN)

Vehicle identification number

I confirm that I have taken delivery of the specified vehicle in good condition, have been shown how to operate it correctly, and the terms of the warranty have been explained to me.

(Whichever comes first).



Vendor's stamp and signature

ŠKODA Partner

Customer's signature



ŠKODA extended warranty

Limits on the ŠKODA extended warranty

Years:

km:

(Whichever comes first).

ŠKODA Partner's stamp

Valid from:

Preface

You have opted for a ŠKODA – our sincere thanks for your confidence in us.

You have received a vehicle with the latest technology and range of amenities. Please read this Owner's Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use of the vehicle.

If you have any questions about your vehicle, please contact a ŠKODA Partner. We hope you enjoy driving your ŠKODA, and wish you a pleasant journey at all times. Your ŠKODA AUTO a.s. (hereinafter referred to only as ŠKODA or manufacturer)



Terms used

The on-board literature contains the following terms relating to the service work for your vehicle.

“Specialist garage” - a workshop that carries out specialist service tasks for

›

ŠKODA vehicles A specialist garage can be a ŠKODA partner, a ŠKODA service partner or an independent workshop. “ŠKODA service partner” - A workshop that has been contractually authorized

›

by the manufacturer ŠKODA AUTO a.s. or its sales partner to perform service tasks on ŠKODA vehicles and to sell ŠKODA Genuine Parts. “ŠKODA partner” - A company that has been authorized by the manufacturer

›

ŠKODA AUTO a.s. or its sales partner to sell new ŠKODA vehicles and, when applicable, to service them using ŠKODA Genuine Parts and sell ŠKODA Genuine Parts.

Owner's Manual

These operating instructions apply to all body variants of the vehicle and all related models.

The manual describes all possible equipment variants without identifying them as special equipment, model variants or market-dependent equipment.

Consequently, this vehicle does not necessarily contain all of the equipment components described in this Owner's Manual.

The scope of equipment of your vehicle relates to your purchase contract for the vehicle. More information is available from the ŠKODA Partner from whom you bought the vehicle.

The illustrations can differ in minor details from your vehicle; they are only intended for general information.

Materials defect liability and ŠKODA warranty for new cars 5

Mobility warranty and ŠKODA extended warranty

Abbreviations

Using the system

Cockpit

Overview

Instruments and Indicator Lights 10

Instrument cluster Multifunction display (MFD) Service Interval Display 16 MAXI DOT display Warning lights 20

Unlocking and locking

Unlocking and locking Central locking system 31 Remote control Anti-theft alarm system 35 Tailgate Electrical power windows Electric sliding/tilting roof 40

Lights and visibility

Lights 43 Interior lights Visibility Windscreen wipers and washers 50 Rear window

28 28

48 49

Seats and storage 54

Front seats 54 Rear seats 56 Head restraints 57 Boot 58 Variable loading floor in the luggage

compartment (Fabia Estate) 62

Net partition (Fabia Estate) 64 Bicycle carrier in the luggage compartment 65 Roof rack system 67 Useful equipment 69 Storage compartments 72

Heating and air conditioning 77

Heating, ventilation, cooling

Heating Air conditioning system (manual air conditioning

system)

Climatronic (automatic air conditioning system)

Communication and multimedia

Universal telephone preinstallation GSM II 86 Voice control Multimedia 92

Driving

Starting-off and Driving

Steering Starting and stopping the engine 96 Brakes Manual gear shifting and pedals 99 Automatic transmission Running in Economical driving and respect the

environment 104 Avoiding damage to your vehicle 108 Driving abroad

Assist systems 111

Brake assist systems 111 Parking aid 113 Cruise control system 114 START-STOP 116

Towing a trailer 118

Towing device 118 Trailer 121

Safety

Passive Safety 124

General information 124 Correct seated position 125

Seat belts

Wearing seat belts 128

Inertia reel and belt pretensioners

Airbag system

Description of the airbag system 133

Airbag overview Deactivating airbags 137

Transporting children safely

Child seat Fastening systems 143

General Maintenance

Car care

Service intervals 145

Services, modifications and technical alterations

100

Washing the car 150

103

Vehicle exterior care Care of the interior 155

109

128

131

133

134

140 140

145

147

151

Table of Contents

Inspecting and replenishing 158

Fuel 158 Engine compartment 160 Engine oil 164 Coolant 166 Brake fluid 168 Vehicle battery 169

Wheels 173

Tyres and rims 173 Winter use 179

Do-it-yourself

Emergency equipment, and self-help

Emergency equipment Changing a wheel 181 Tyre repair Jump-starting Towing the vehicle 189

Fuses and light bulbs

Fuses 192 Bulbs

180 180

185

187

192

195

Technical data

Vehicle data 201

201

Index

Table of Contents

Materials defect liability and ŠKODA warranty for new cars

Materials defect liability

Your ŠKODA partner, as a vendor, is liable to you for defects in your new ŠKODA car, ŠKODA Genuine Parts or ŠKODA Genuine Accessories in accordance with statutory regulations and the purchase agreement.

ŠKODA warranty for new cars

As well as the materials defect liability, ŠKODA AUTO a.s. grants you the ŠKODA warranty for new cars (hereafter referred to as “ŠKODA warranty),” according to the terms described below.

As part of the ŠKODA warranty, ŠKODA AUTO a.s. will guarantee the following services:

Repair of damage to your vehicle that occurs within two years from the start of

›

the ŠKODA warranty; Repair of paint damage to your vehicle that occurs within three years from the

›

start of the ŠKODA warranty; Repair of rust perforation to the bodywork of your vehicle that occurs within

›

twelve years from the start of the warranty. Only rust perforation from the inside to the outside of body panels is considered to be rust perforation of the bodywork and is covered by the ŠKODA warranty.

The start of the warranty is the date on which the original purchaser acquires the vehicle upon purchasing it from the ŠKODA partner or the date of first registration. Whichever occurs first and is accordingly recorded by the ŠKODA partner in the service schedule is the applicable date.

Defects may be remedied by replacement or repair of the defective part. Replaced parts become the property of the ŠKODA service partner.

There are no other entitlements arising from the ŠKODA warranty. In particular, there are no entitlements to replacement, cancellation, provision of a courtesy vehicle for the duration of repairs or compensation for loss.

If your ŠKODA vehicle was purchased from a ŠKODA partner in a country within the European Economic Area (i.e. the countries of the European Union, Norway, Iceland and Liechtenstein) or in Switzerland, claims arising from the ŠKODA warranty must also be made through a ŠKODA service partner in one of these countries.

If your ŠKODA vehicle has been purchased from a ŠKODA partner outside the European Economic Area and Switzerland, claims arising from the ŠKODA warranty must also be made through a ŠKODA service partner outside the European Economic Area and Switzerland.

One of the conditions for the assertion of the ŠKODA warranty is that all service operations have been carried out works in a timely and adequate manner and in accordance with the manufacturer's provisions. You must prove that service operations have been carried out properly and in accordance with the manufacturer's provisions when asserting a claim under the ŠKODA warranty. Where a service has been missed or not carried out according to the manufacturer's provisions, you may still be entitled to warranty claims as long as you can prove that the missed service or the failure to carry out a service according to the manufacturer's provisions was not the cause of the defect.

Natural wear and tear of your vehicle is not covered by the ŠKODA warranty. The ŠKODA warranty also does not cover defects to bodywork, installations and conversions provided by third-parties, nor vehicle defects caused by these. The same is true for accessories which are not factory installed and/or supplied.

In addition, this warranty does not apply if the defect was caused by one of the following:

unauthorized use, improper handling (e.g. use in motorsport competitions or

›

overloading), improper care and maintenance, or unapproved modification to your vehicle; non-compliance with provisions in the service schedule and the Owner's manual

›

or other factory-supplied instructions; external causes or influences (e.g. accidents, hail, flooding, etc.);

›

parts fitted or installed on the vehicle the use of which is not approved by

›

ŠKODA AUTO a.s., or modification of the vehicle in a manner not approved by ŠKODA AUTO a.s. (e.g. tuning); damage caused by you which was not immediately seen to by specialist garage

›

or was not fixed properly. It is the customer's responsibility to prove that it was not the cause. This ŠKODA warranty does not affect the purchaser's statutory rights arising from

liability for defects by the vehicle vendor and other potential claims under product liability laws.



Materials defect liability and ŠKODA warranty for new cars

Mobility warranty and ŠKODA extended warranty

Mobility warranty

The mobility warranty provides a sense of security when travelling in your vehicle. Should your car break down when you're on the move one day as a result of an

unexpected fault, you will be eligible for services to ensure your continued mobility as part of the mobility warranty, which includes the following: Breakdown service at the breakdown location and towing to the ŠKODA service partner, technical assistance by phone or in person.

If your vehicle is not repaired on the same day, the ŠKODA service partner may provide further services as required, such as replacement transportation (bus, train, etc.), a courtesy vehicle, etc.

You can obtain more information regarding terms and conditions for the provision of mobility warranty for your vehicle from your ŠKODA partner. Here you will also be given detailed terms and conditions of the mobility warranty as it relates to your vehicle. In the event that there is no mobility warranty coverage available for your vehicle, you should check with any ŠKODA service partner about the possibility of concluding a contract retrospectively.

Note

The mobility warranty is only available in some countries.

Optional ŠKODA extended warranty

If you received an extended ŠKODA warranty when purchasing your new car, the two-year ŠKODA warranty for defects in your ŠKODA vehicle will be extended by the period you chose or until the chosen mileage limit has been reached.

The paintwork warranty and the warranty against rust perforation referred to above stay unaffected by the extended warranty.

Detailed conditions for the extended warranty are included in the extended warranty terms and conditions, which your ŠKODA partner will have given you when you purchased your new vehicle.

Note

The mobility warranty and optional extended ŠKODA warranty are only available in some countries.

Mobility warranty and ŠKODA extended warranty



Abbreviations

Abbreviation Definition

rpm Engine revolutions per minute

ABS Anti-lock brake system

AG Automatic gearbox

TCS Traction control

CO2 in g/km discharged quantity of carbon dioxide in grams per driven kilo-

meter DPF Diesel particle filter DSG Automatic double clutch gearbox EDL Electronic differential lock ECE Economic Commission for Europe ESC Electronic Stability Control

EU European Union kW Kilowatt, measuring unit for the engine output MG Manual gearbox

MFD Multifunction display

N1 Panel van intended exclusively or mainly for the transporta-

tion of goods

Nm Newton meter, measuring unit for the engine torque

TDI CR Diesel engine with turbocharging and common rail injection

system

TSI Petrol engine with turbocharging and direct injection



Abbreviations

Fig. 1

Using the system

Cockpit

Using the system

Cockpit

Overview

Door handle 30

Electrical power windows 39

Electric exterior mirror adjustment 53

Air outlet vents 77

Car park ticket holder 71

Operating stalk:

Turn signal light, headlight and parking light, headlight flasher 45

›

Speed regulating system

›

Steering wheel:

With horn

›

With driver’s front airbag

›

With pushbuttons for radio, navigation system and mobile

›

phone 86

Instrument cluster: Instruments and warning lights 10

Operating stalk:

Windscreen wiper and wash system

›

Multifunction display 13

›

MAXI DOT display

›

Button for rear window heater 50

TCS switch

Air outlet vents in the central part of the instrument panel 77

Hazard warning light system button

Warning light for the deactivated front seat passenger airbag

Depending on equipment fitted:

Operating controls for the heating 78

›

Operating controls for the air conditioning system 80

›

Operating controls for Climatronic

›

Storage compartments on the front passenger side

Front passenger airbag 135

Air outlet vents

Key-operated switch for the front seat passenger airbag 138

Door handle 30

Switch depending on equipment fitted:

Boot lid remote release 37

›

Interior monitor 36

›

Light switch and headlamp beam adjustment 43, 44

Fuse box in the dashboard 193

Bonnet release lever 162

Lever for adjusting the steering wheel 95

Ignition lock 97

Pedals 100

Depending on equipment fitted:

Gear lever (manual gearbox) 100

›

Selector lever (automatic gearbox) 101

›

Rocker switch for front left seat heating

114

135

Central locking system 33

Handbrake

Rocker switch for front right seat heating 55

Depending on equipment fitted:

Ashtrays

›

Storage compartment 74

›

Depending on equipment fitted:

Radio

›

Navigation system

›

MDI

Note

112

The layout of the controls on right-hand drive vehicles differs partially from that shown in » Fig. 1. The symbols on the controls and switches are the same as for

left-hand drive models.

138



Cockpit

Instruments and Indicator Lights

Instrument cluster

Introduction



This chapter contains information on the following subjects: Overview

Engine revolutions counter 11 Speedometer 11 Coolant temperature gauge display 11 Fuel gauge 11 Counter for distance driven 12 Digital clock Display of the second speed 12 Recommended gear

Fault display

The Error message will appear in the display if there is a fault in the instrument cluster. Ensure that the fault is rectified as soon as possible by a specialist workshop.

WARNING

■

Concentrate fully at all times on your driving! As the driver you are fully re-

sponsible for road safety.

■

Never operate the controls in the instrument cluster while driving, only

when the vehicle is stationary!

Overview

Fig. 2 Instrument cluster



Rev counter with warning lights » page 11

Display:

› › › › ›

Speedometer with warning lights » page 11

Coolant temperature gauge1) » page 11



Button for display mode:

› › ›

First read and observe the introductory information and safety warnings on page 10.

With counter for distance driven » page 12 With service interval display » page 16 With digital clock » page 12 with multifunction display (MFD) » page 13 with the MAXI DOT display » page 18

Setting the hours/minutes » page 12 Enable/disable display of the second speed2) » page 12 Service interval2) - Display of the number of days, kilometres or miles remaining until the next Service3) » page 16



Applies for vehicles using the MAXI DOT display.

Applies for vehicles with a segment display.

Applies for models in which where the values are indicated in British measuring units.

Using the system

Button for:

Reset trip meter » page 12

›

Set hours/minutes

›

Enable/disable the mode selected by means of button

›

Fuel gauge1) » page 11

Engine revolutions counter

First read and observe the introductory information and safety warnings on page 10.



The red scale of the rev counter 1 » Fig. 2 on page 10 indicates the range in which the engine control unit begins to limit the engine speed. The engine control unit restricts the engine speed to a steady limit.

You should shift into the next higher gear before the red scale of the revolution counter is reached, or move the selector lever into position D if your car is fitted with an automatic gearbox.

To maintain the optimum motor speed, observe the gearshift indicator » page 13.

For the sake of the environment

Shifting up in good time has the following benefits.

■

It helps to reduce fuel consumption.

■

It reduces engine noise.

■

It protects the environment.

■

It benefits the service life and reliability of the engine.

Speedometer

First read and observe the introductory information and safety warnings on page 10.



Warning against speeding

An audible warning signal will sound when the vehicle speed exceeds 120 km/h2). The audible warning is switched off once the vehicle speed falls below 120 km/h.

Coolant temperature gauge display

First read and observe the introductory information and safety warnings on page 10.





The coolant temperature gauge 4 » Fig. 2 on page 10 operates only when the ignition is switched on.

In vehicles with a segment display, the coolant temperature is indicated only by one of the warning lights » page 22,   Coolant coming on or going off.

Cold range

The pointer in the left of the scale indicates that the engine has not yet reached its operating temperature. Avoid high speeds, full throttle and high engine loads. This prevents possible damage to the engine.

The operating range

The engine has reached its operating temperature as soon as the pointer moves into the middle of the scale. At very high ambient temperatures or under heavy engine loads, the pointer may move even further to the right.

High temperature range

The coolant temperature is too high if the pointer reaches the red area of the scale. Further information » page 22.

CAUTION

Additional headlights and other components mounted in front of the air inlet impair the cooling efficiency of the coolant.



Fuel gauge

First read and observe the introductory information and safety warnings on page 10.



The fuel gauge 7 » Fig. 2 on page 10 only works when the ignition is switched on.

The fuel remaining is displayed in the segment display on vehicles with the seg-



ment display.





Applies for vehicles using the MAXI DOT display.

This function is only enabled in certain countries.

Instruments and Indicator Lights

The fuel tank has a capacity of about 45 litres. The warning light lights up when the fuel level reaches the reserve range  » page 25.

CAUTION

Never drive until the fuel tank is completely empty! The irregular supply of fuel can cause misfiring. This can result in considerable damage to parts of the engine and the exhaust system.

Counter for distance driven

First read and observe the introductory information and safety warnings on page 10.



The distance which you have driven with your vehicle is shown in km. In some countries the measuring unit “mile” is used.

Daily trip counter (trip)

The trip counter indicates the distance you have driven since it was last reset - in steps of 100 metres or 1/10 of a mile.

Reset trip meter

The meter can be reset by pressing and holding button

Odometer

The odometer indicates the total distance in kilometres or miles which the vehicle has been driven.

» Fig. 2 on page 10.

Note

If the second speed display is enabled on vehicles with a segment display, this speed will be shown instead of the odometer.

Digital clock

First read and observe the introductory information and safety warnings on page 10.



The clock is set with buttons 5 and 6 » Fig. 2 on page 10.

Select the display that you wish to change with the button 5 and carry out the change with the button 6.

In vehicles equipped with the MAXI DOT display, it is also possible to set the clock in the Time menu » page 18.

Display of the second speed



First read and observe the introductory information and safety warnings on page 10.



The display can show the current speed in mph1). This feature is provided for driving in countries with different units for speed.

MAXI DOT display

The display of the second speed can be set in the Settings menu item » page 18, Settings.

Segment display

Press the 5 » Fig. 2 on page 10key repeatedly, until the odometer display flash-

›

es » page 12. Press the 6 key while the display is flashing.

›

The second speed is displayed instead of the odometer. Display of the second speed can be disabled in the same way.



On models on which the speedometer indicates mph, the second speed is displayed in km/h.

Using the system

Recommended gear

Fig. 3

Recommended gear

First read and observe the introductory information and safety warnings on page 10.



The gear currently engaged is shown in the instrument cluster display A » Fig. 3. In order to minimise the fuel consumption, a recommendation for shifting into an-

other gear is indicated in the display. If the control unit recognises that it is beneficial to change gear, an arrow B is

shown in the display. The arrow points up or down, depending on whether you should shift into a higher or lower gear.

At the same time, the recommended gear is shown at

lected on vehicles with a manual gearbox.

instead of the gear se-

CAUTION

The driver is always responsible for selecting the correct gear in different driving situations, such as overtaking.

Multifunction display (MFD)

Multifunction display details 15 Warning against speeding 16

The multifunction display can only be operated when the ignition is switched on. After the ignition is switched on, the function displayed is the one which you last selected before switching off the ignition.

The multifunction display shown in the segment display » Fig. 4 on page 14 or in the MAXI DOT display depending on your vehicle model » page 18.

On vehicles with a MAXI DOT display » page 18, there is an option not to display some of the information.

WARNING

■

Concentrate fully on your driving at all times. As the driver you are fully re-

sponsible for the operation of your vehicle.

■

Even at temperatures of around +4 °C, there may still be black ice on the road surface. You should therefore not rely solely on the outside temperature display for accurate information as to whether there is ice on the road.

Note

■

In certain national versions the displays appear in the Imperial system of meas-

ures.

■

If the display of the second speed is activated in mph, the current speed is not

indicated in km/h on the display.





Introduction

This chapter contains information on the following subjects: Memory 14

Operation 14

Instruments and Indicator Lights

Memory

Fig. 4

Multifunction display

First read and observe the introductory information and safety warnings on page 13.



The multifunction display is equipped with two automatic memories. The selected memory is shown in the Display » Fig. 4.

The data of the single-trip memory (memory 1) is shown if a 1 appears in the display. A 2 shown in the display means that data relates to the total distance memory (memory 2).

Switch memories using button stalk.

Single-trip memory (memory 1)

The single-trip memory collates the driving information from the moment the ignition is switched on until it is switched off. New data will also flow into the calculation of the current driving information if the trip is continued within 2 hours after switching off the ignition. If the trip is interrupted for more than 2 hours, the memory is automatically erased.

Total-trip memory (memory 2)

The total trip memory collates the data from any number of individual trips up to a total of 19 hours and 59 minutes or 1999 km or, for vehicles with a MAXI DOT display, 99 hours and 59 minutes, or 9999 km. The memory is deleted when either of these limits is reached and the calculation starts all over again.

Unlike the single-trip memory, the total-trip memory is not deleted after a period of interruption of driving of 2 hours.

» Fig. 5 on page 14 on the windscreen wiper

Note

All information in the memory 1 and 2 is erased if the battery of the vehicle is disconnected.

Operation

Fig. 5

Multifunction display: Control elements

First read and observe the introductory information and safety warnings



The Toggle button for selecting menu items A » Fig. 5 and button B are found on the wiper stalk.

Select menu items

Briefly press the top or bottom of rocker switch A » Fig. 5. This opens the indi-

›

vidual menu items in the multifunction display one after the other.

Select memory

Press button B » Fig. 5.

›

Reset memory

Select the desired memory.

›

Press and hold button B » Fig. 5.

›

The following values from the memory selected will be set to zero by button B.

Average fuel consumption.

›

Distance driven.

›

Average speed.

›

Driving time

›

on page 13.



Using the system

Multifunction display details

First read and observe the introductory information and safety warnings on page 13.



Outside temperature

The current outside temperature is displayed1). The temperature is shown with the snowflake symbol  (ice warning) if the out-

door temperature is below +4 °C. This display flashes for a few seconds, then shows the most recently displayed

function2) . If the temperature drops below +4 °C while the car is driving at a speed faster

than 10 km / h, a beep is also heard.

Driving time

The driving time elapsed since the memory was last erased appears in the display. Reset the memory to zero by pressing the button » page 14, Operation to measure the driving time from a particular moment.

The maximum time indicated in both memories is 19 hours and 59 minutes and on vehicles which are fitted with a MAXI DOT display, it is 99 hours and 59 minutes. The indicator is reset to zero when this value is exceeded.

Current fuel consumption

The current fuel consumption level is displayed in litres/100 km3). You can use this information to adapt your driving style to the desired fuel consumption.

The display appears in litres/hour if the vehicle is stationary or driving at a low speed4).

Average fuel consumption

The average fuel consumption since the memory was last erased is displayed in litres/100 km3).

Set the memory to zero at the start of a new measurement if you wish to determine the average fuel consumption over a certain period » page 14, Operation. No value will appear in the display after it has been erased until you have driven approximately 300 m.

The display is updated regularly while you are driving.

Range

The estimated range is displayed in kilometres. It indicates the distance you can still drive with your vehicle based on the level of fuel in the tank and the same style of driving.

The display is shown in steps of 10 km. The value is displayed in steps of 5 km after the  warning light has come on.

The fuel consumption over the preceding 50 km is used to calculate the information. The range will increase if you drive in a more economical manner.

If the memory is set to zero (after the battery has been disconnected), a fuel consumption of 10 l/100 km is used initially, then the value is adapted according to the style of driving.

Distance travelled

The distance travelled since the memory was last erased is displayed. Reset the memory to zero if you want to measure the distance travelled from a particular moment » page 14, Operation.

The maximum distance indicated in both memories is 1999 km or 9999 km on vehicles with a MAXI DOT display. The indicator is reset to zero when this value is exceeded.

Average speed

The average speed since the memory was last erased is displayed in km/hour . Set the memory to zero at the start of measurement to determine the average speed over a certain period » page 14, Operation.

No value will appear in the display until you have driven approximately 300 m after this information has been deleted.

The display is updated regularly while you are driving.



This information is always shown on vehicles with a MAXI DOT display.

This is not the case on the MAXI DOT display.

On some models in certain countries, the display appears in kilometres/litre.

On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is stationary.

Instruments and Indicator Lights

Current speed

The current speed, identical to the display on the speedometer 3 » Fig. 2 on page 10, is displayed.

Oil temperature

The current engine oil temperature is displayed. If the oil temperature is lower than 50 °C or if a fault in the system for checking the oil temperature is present, only - -.- is displayed instead of the oil temperature.

Warning against speeding

The warning that the speed limit is being exceeded can be enabled/disabled in the display » page 16.

Change or delete speed limit

Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)

›

or  (segment display) menu item. Pressing button B disables the speed limit.

›

Pressing the button B activates the ability to change the speed limit.

›

If the set speed limit is exceeded, an audible signal will sound as a warning. The Warning at (MAXI DOT display) or  (segment display) menu item appears in the display with the limit set.

The speed limit set mode is stored even after the ignition is switched off and on.



Warning against speeding

First read and observe the introductory information and safety warnings on page 13.



Adjust the speed limit while the vehicle is stationary

Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)

›

or  (segment display) menu item. Press button B to activate the ability to set the speed limit2) (value flashes).

›

Use the button A to set the required speed limit, e.g. 50 km/h.

›

Confirm the speed limit that was set with button B, or wait approx. 5 seconds

›

until the setting is saved automatically (the value stops flashing).

This allows you to set the speed in 5 km/h intervals.

Adjusting the speed limit while the vehicle is moving

Press button A » Fig. 5 on page 14 to select the Warning at (MAXI DOT display)

›

or  (segment display) menu item. Drive at the desired speed, e.g. 50 km/h.

›

Press button B to accept the current speed as the speed limit (the value flash-

›

es).

If you wish to adjust the set speed limit, you can do so in 5 km/h intervals (e.g. the accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).

Confirm the speed limit that was set by pressing button B again, or wait ap-

›

prox. 5 seconds until the setting is saved automatically (the value stops flashing).

Applies for vehicles equipped with the MAXI DOT display.

An initial value of 30 km/h is displayed automatically if no value has been specified.

Using the system

Service Interval Display



Introduction

This chapter contains information on the following subjects: Prompt in the segment display

Display in the MAXI DOT display

A message concerning the kilometres and days remaining until the next service is due is shown for about 10 seconds after the ignition is switched on until the

end of the service interval is reached. The kilometre indicator or the days indicator reduces in steps of 100 km or days

until the service due date is reached.

Note

■

Information is retained in the Service Interval Display even after the vehicle bat-

tery is disconnected.

■

If the instrument cluster is exchanged after a repair, the correct values must be entered in the counter for the Service Interval Display. This work will be done by a specialist garage.

■

For more information on the service intervals » page 145, Service intervals.

17 17



Prompt in the segment display

Fig. 6

Example of a message

First read and observe the introductory information given on page 16.



Oil change service

If an oil change service is due, the  icon and the number 1 is displayed at the position identified with the arrow for approximately 10 seconds » Fig. 6.

The  icon is shown together with the days and kilometres remaining to the next service.

As soon as the service due date is reached, the flashing  icon and the message OIL CHNG appears in the display for about 20 seconds after the ignition is switched on.

Inspection

If an inspection is due, the  icon and the number 2 are displayed at the position identified with the arrow for approximately 10 seconds » Fig. 6.

The  icon is shown together with the days and kilometres remaining to the next service.

As soon as the due date for the service is reached, the flashing  icon and the INSPEC _ message appear in the display for about 20 seconds after the ignition has been switched on.

Display the days and distance until the next service

You can press button distance and time to until the next service whenever the ignition is switched on.

The  icon appears together with the  icon and the distance and time to the next service appear in the display for about 10 seconds.

» Fig. 2 on page 10 repeatedly to display the remaining

The distance and the days remaining until the next oil change service are displayed first; the distance and the days remaining until the next inspection are displayed after the button 5is pressed again.

Note

The kilometres remaining until the next service are displayed instead of the odometer.

Display in the MAXI DOT display

First read and observe the introductory information given on page 16.



Oil change service

If an oil change service is due, the message Oil change in ... km or .... days ap-

pears.

As soon as the service date has arrived, the message Oil change now! appears after the ignition is switched on.

Inspection

If an inspection is due, the message Inspection in ... km or ... days appears. As soon as the service interval date has arrived, the message Inspection now! ap-

pears after the ignition is switched on.

Displaying the distance and days until the next service interval You can display the remaining distance and days until the next service in the Settings menu whenever the ignition is switched on » page 18.

The following message is displayed for 10 seconds.

Oil change ... km / ... days Inspection ... km / ... days



Instruments and Indicator Lights

MAXI DOT display

 Introduction

This chapter contains information on the following subjects: Main menu

Settings 18 Door, boot lid and bonnet warning 19 Auto Check Control 19

The MAXI DOT display provides you with information about the current operating state of your vehicle. The information system also provides you with data (depending on the vehicle equipment) relating to the radio, mobile phone, multifunctional display, navigation system, the device connected to the MDI input and the automatic gearbox » page 100.

Lighting up of certain symbols is combined with an acoustic warning signal.

WARNING

Concentrate fully on your driving at all times. As the driver you are fully responsible for the operation of your vehicle.

Main menu

Fig. 7

Operating stalk: MAXI DOT display controls

First read and observe the introductory information and safety warnings on page 18.



Press and hold rocker switch A » Fig. 7 to activate the MAIN MENU.

›

Individual menu items can be selected by pressing rocker switch A. When the

›

pushbutton B is briefly pressed, the information you have selected is dis-

played.

Overview of the menu items in the main menu.

■

MFD (Multifunction display) » page 13

■

Audio » Operating instructions for the radio

■

Navigation » Operating instructions for the navigation system

■

Phone » page 86;

■

Vehicle status » page 19

■

Settings » page 18 The Audio and Navigation menu items are only displayed when the factory-fitted

radio or navigation system is switched on.

Note

■

Warning messages shown in the information display must be confirmed by pressing button B briefly » Fig. 7 to call up the main menu.

■

The menu always shifts to one of the higher levels after 10 seconds if the display is not currently active.

■

Using the factory-fitted radio or navigation system » Radio operating instructions or» Navigation system operating instructions.



Settings

First read and observe the introductory information and safety warnings on page 18.



You can change certain settings yourself through the MAXI DOT display. The current menu item is shown in the top of the display under a line.

You can select the following menu options:

Language

You can set the language for the warning and information texts here.

MFD data

Activate or deactivate certain displays of the multifunction display here.

Time

The time, time format (12 or 24 hour indicator) and the changeover between summer/winter time can be set here.





Using the system

Winter tyres

Here, you can set the speed at which an audible signal should sound. This function is, for example, used for winter tyres where the maximum permissible speed is lower than the maximum speed of the vehicle.

The following is shown on the information display if this speed is exceeded:

Winter tyres: maximum ... km/h.

Units of measurement

The units for the temperature, consumption and distance driven can be set here.

Alt. speed dis.

Display of the second speed in mph1) can be activated here.

Service

The days and kilometres remaining until the next service can be displayed here.

Factory setting

The display can be restored to its factory settings here.

Door, boot lid and bonnet warning

First read and observe the introductory information and safety warnings on page 18.



If at least one door is open, or the boot or bonnet is open, the MAXI DOT display shows the vehicle with the corresponding door or boot/bonnet open.

An audible signal also sounds if the vehicle is travelling at more than 6 km/h.

Auto Check Control

First read and observe the introductory information and safety warnings on page 18.



Vehicle condition

Certain functions and conditions of individual vehicle systems are checked continuously when the ignition is switched on and also while driving.

Some error messages and other information are displayed in the MAXI DOT display. The messages are displayed simultaneously with the icons in the MAXI DOT display or with the warning lights in the instrument cluster » page 20.

The Vehicle status menu item is shown in the main menu of the MAXI DOT display whenever at least one fault message is present. The first of the fault messages is displayed after this menu item is selected. Several error messages are shown on the display under the message e.g. 1/3. This indicates that the first of a total of three error messages is being displayed.

As long as the operational faults are not rectified, the symbols are always indicated again. After they are displayed for the first time, the symbols continue to be indicated without any extra messages for the driver.

Warning symbols











Clutches in the automatic gearbox are too hot

The  symbol in the MAXI DOT display indicates that the temperature of the automatic gearbox clutches is too high.

The following message is shown in the MAXI DOT display.

Gearbox overheating. Stop. Read manual.





Stop the vehicle, switch off the engine, and wait until the icon goes out – there is a risk of gearbox damage. You can continue your journey as soon as the icon disappears.

Engine oil pressure too low » page 21

Clutches in the automatic gearbox are too hot

Check engine oil level, engine oil sensor defective

» page 19

» page 21

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 47.



On models on which the speedometer indicates mph, the second speed is displayed in km/h.

Instruments and Indicator Lights

Note

■

Warning messages shown in the MAXI DOT display must be confirmed with but-

ton B » Fig. 7 on page 18 to call up the main menu.

■

Warning lights



Introduction

This chapter contains information on the following subjects:



Handbrake 20



Brake system 20



Seat belt warning light 21



Alternator



Door open

 

Engine oil 21

 

Coolant 22



Power steering 23



Electronic Stability Control (ESC)



Traction Control System (ASR)



Antilock brake system (ABS) 24



The rear fog light 24



Bulb failure 24



Exhaust inspection system



Glow plug system (diesel engine)



ECU fault light (petrol engine) 25



Diesel particulate filter (diesel engine)



Fuel reserve



Airbag system



Tyre pressure



Windscreen washer fluid level 26



Traction control (TCS) switched off

 

Turn signal system



Low beam

 Fog lights 27

 Cruise control system

 Selector lever lock 27

 Main beam

The warning lights show certain functions/faults and may be accompanied by audible signals.



WARNING

■

If illuminated warning lights and the corresponding descriptions and warning notes are not observed, this may result in severe injuries or major vehicle damage.

■

The engine compartment of your car is a hazardous area. There is a risk of injuries, scalding, accidents and fire when working in the engine compartment, e.g. inspecting and replenishing oil and other fluids. It is essential to observe safety notes » page 160, Engine compartment.

21 21

23 23

24 24

25 25 26 26

26 26 27



Handbrake

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on if the handbrake is applied. An audible warning is also given if you drive the vehicle for at least 3 seconds at a speed of more than 6 km/h.

The following message is shown in the MAXI DOT display.



Release parking brake!



Brake system

First read and observe the introductory information and safety warnings on page 20.



The  indicator light comes on if the brake fluid level in the braking system is too low or there is a fault in the ABS.

The following message is shown in the MAXI DOT display.

Brake fluid: Read manual.







Using the system

Stop the vehicle, switch off the engine, and check the level of the brake fluid » page 168.

Further information » page 98, Brakes.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 47.

■

The following guidelines should be observed when opening the bonnet and checking the brake fluid level » page 160, Engine compartment.

■

If the warning light  is displayed simultaneously with warning light

 » page 24,  Antilock brake system (ABS),  do not continue your jour-

ney! Seek help from a specialist garage.

■

A fault to the ABS system or the braking system can increase the vehicle's braking distance – there is a risk of accident.



Seat belt warning light

First read and observe the introductory information and safety warnings on page 20.



The  indicator light comes on after the ignition is switched on as a reminder for the driver and front passenger to fasten their seat belt. The indicator light only goes out once the driver and front passenger have fastened their seat belt.

A steady warning signal sounds at vehicle speeds greater than 20 km/h and the flashes if the driver and front passenger have not fastened their seat belts.

The warning signal is switched off and the  indicator light is permanently lit if the driver and front passenger have not fastened their seat belts within the next 90 seconds.

Further information » page 128.



Alternator

First read and observe the introductory information and safety warnings on page 20.



If the warning light lights up  when the engine is running, the vehicle battery is not being charged.

Seek help from a specialist garage. The electrical system requires checking.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 47.

CAUTION

 Do not continue driving if the  warning light (coolant system fault) lights up

in addition to the  warning light while you are driving. Stop the engine - there is a risk of engine damage.

 Door open



First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on if one or several doors are opened or if the boot lid is opened.

The warning light comes on even when the ignition is switched off. The warning light lights up for a maximum of 5 minutes.

WARNING



If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 47.

 





The warning light  lights up red (low oil pressure)

The following message is shown in the MAXI DOT display.



Engine oil

First read and observe the introductory information and safety warnings on page 20.

Oil pressure: Engine off! Read manual.





Instruments and Indicator Lights

The warning light  comes on for a few seconds when the ignition is switched on1).

Stop the vehicle, switch off the engine, and check the engine oil level » page 165. Even if the oil level is correct,  do not drive any further if the warning light is

flashing. Also do not leave the engine running at an idling speed. Seek help from a specialist garage.

The warning light  lights up yellow (oil quantity too low)

The following message is shown in the MAXI DOT display.

Check oil level!



Stop the vehicle, switch off the engine, and check the engine oil level » page 165. An audible signal sounds as a warning signal. The warning light will go out if the bonnet is left open for more than 30 seconds.

If no engine oil has been replenished, the warning light will come on again after driving about 100 km.

The warning light  flashes yellow (engine oil level sensor faulty)

The following message is shown in the MAXI DOT display.

Oil sensor workshop!



If the engine oil level sensor is faulty, the warning light flashes  several times and an audible signal sounds when the ignition is turned on.

Seek help from a specialist garage.

WARNING

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and switch on the hazard warning lights system » page 47.

CAUTION

The red oil pressure light check the oil level at regular intervals, preferably after every refuelling stop.

 is not an oil level indicator! One should therefore

  Coolant

First read and observe the introductory information and safety warnings on page 20.



The indicator light  lights up until the engine reaches operating temperature2). Avoid high speeds, full throttle and high engine loads.

If the warning light  lights up or flashes, either the coolant temperature is too high or the coolant level is too low.

An audible signal sounds as a warning tone. The following message is shown in the MAXI DOT display.

Check coolant. Read manual.



Stop the vehicle, switch off the engine, check the level of the coolant » page 167, and refill the coolant if necessary » page 168.

If the coolant is within the specified range, the increased temperature may be caused by an operating problem at the radiator fan. Check the fuse for the radiator fan, replace if necessary » page 194, Fuses in the engine compartment.

Do not continue driving if the warning light   does not go off even though the

coolant level is correct and the fuse for the fan is in working order!

Seek help from a specialist garage.

WARNING

■

If you have to stop for technical reasons, park the vehicle at a safe distance from the traffic, switch off the engine and activate the hazard warning light system » page 47.

■

Carefully open the coolant expansion bottle. If the engine is hot, the cooling system is pressurized - risk of scalding! It is therefore best to allow the engine to cool down before removing the cap.

■

Do not touch the radiator fan. The radiator fan may switch itself on automatically even if the ignition is off.



The  warning light does not light up in vehicles fitted with the MAXI DOT display when the ignition is switched on, but only if there is a fault or the engine oil level is too low.

Not on vehicles with the MAXI DOT display.

Using the system

 Power steering

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on for a few seconds when the ignition is switched on.

If the warning light after switching on the ignition or when driving lights up continuously, a fault exists in the electrohydraulic power steering. The power steering operates with reduced steering assist or does not function at all.

Seek help from a specialist garage. Further information » page 95.

Seek help from a specialist garage.

The ESC system cannot be turned off, the  » page 112 button only switches the

TCS off, the  warning light in the instrument cluster lights up.

As the ESC operates in conjunction with the ABS, the ESP indicator light will also

come on if the ABS system fails.

Further information » page 111, Stabilisation control (ESC).

Note

The  warning light comes on after the ignition is switched on if the vehicle's

battery has been disconnected and reconnected. The warning light should go out

after the vehicle has driven a short distance.



Note

■

If the yellow warning light  goes out after the engine is restarted and a short

drive, it is not necessary to visit a specialist garage.

■

If the vehicle battery has been disconnected and reconnected, the yellow warning light  comes on after switching on the ignition. The warning light should go out after driving a short distance.

■

There is no power-assisted steering support when the vehicle is being towed without the engine running or when the power-assisted steering is defect. The vehicle is fully steerable however. There is however increased force required to turn the steering wheel.



Electronic Stability Control (ESC)

First read and observe the introductory information and safety warn-

on page 20.

ings



The warning light flashes to show that the ESC is currently operating. If the warning light  comes on immediately after you start the engine, the ESC

might be switched off due to technical reasons. Switch the ignition off and on again. The ESC is fully functional again if the  warning light does not light up after you switch the engine back on.

There is a fault in the ESC system if the  warning light lights up. The following message is shown in the MAXI DOT display.

Fault: Electronic Stability Control (ESC)





Traction Control System (ASR)

First read and observe the introductory information and safety warnings on page 20.



The warning light flashes to show that the ASR is currently operating. If the warning light  comes on immediately after starting the engine, the ASR

can be switched off for technical reasons. Switch the ignition off and on again. The TCS is fully functional again if the  warning light does not light up after you



switch the engine back on. If the warning light  lights up, there is a fault in the ASR. The following message is shown in the MAXI DOT display.

Fault: Traction control (TCS)



Seek help from a specialist garage. The fact that the TCS system operates together with the ABS means that the TCS

warning light will also come on if the ABS system is not operating properly. Further information » page 112, Traction Control System (ASR).

Note

 warning light comes on after the ignition is switched on if the vehicle's

The battery has been disconnected and reconnected. The warning light should go out after the vehicle has driven a short distance.

Instruments and Indicator Lights



 Antilock brake system (ABS)

First read and observe the introductory information and safety warnings on page 20.



If the warning light  lights up, there is a fault in the ABS. The following message is shown in the MAXI DOT display.

Fault: ABS



The vehicle will only be braked by the normal brake system without the ABS. Seek help from a specialist garage.

WARNING

■

If you have to stop for technical reasons, then park the vehicle at a safe dis-

tance from the traffic, switch off the engine and activate the hazard warning light system » page 47.

■

If the warning light  » page 20 is displayed simultaneously with the ABS

warning light ,  do not continue your journey! Seek help from a specialist garage.

■

A fault to the ABS system or the braking system can increase the vehicle's

braking distance – there is a risk of accident.



The rear fog light

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on when the rear fog lights are operating » page 46.



Bulb failure

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on if a bulb is faulty:

within a few seconds of the ignition being switched on;

›

when a light with a defective bulb is switched on.

›

The following message may be shown in the MAXI DOT display, for example.

INFORMATION Check front right low beam!



Note

The rear side lights and the licence plate lighting have several light bulbs. The indicator light  only lights up if all light bulbs of the licence plate lighting or the parking light (in one rear light) are defective. For this reason, regular check that these light bulbs are working correctly.

 Exhaust inspection system

First read and observe the introductory information and safety warnings on page 20.



If the warning light  lights up, there is a fault in the exhaust inspection system. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.





Glow plug system (diesel engine)

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on after the ignition has been switched on. The engine can be started immediately after the pre-glow warning light goes out.

There is a fault in the glow plug system if the warning light  does not come on at all or lights up continuously.

If the warning light  begins to flash while driving, a fault exists in the engine control. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.



Using the system

 ECU fault light (petrol engine)

First read and observe the introductory information and safety warnings on page 20.



If the warning light  comes on or begins to flash while driving, a fault exists in the engine control unit. The engine control unit allows the vehicle to run in emergency mode.

Seek help from a specialist garage.



Diesel particulate filter (diesel engine)

First read and observe the introductory information and safety warnings on page 20.



The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a regular basis.

The  warning light comes on if soot has accumulated in the filter. In order to clean the filter, and where traffic conditions permit »

should be driven for at least 15 minutes or until the warning light goes out at an steady speed of at least 60 km/h at engine speeds of 1800 - 2500 rpm with 4th or 5th gear engaged (automatic gearbox: position S).

The  warning light only goes out once the diesel particulate filter has been successfully cleaned.

If the filter is not properly cleaned, the warning light  does not go out and the warning light  begins to flash.

The following message is shown in the MAXI DOT display.

Diesel particulate filter: Read manual.



The engine control unit allows the vehicle to run in emergency mode. After switching the ignition off and on again the indicator light, the indicator light also lights up.

Seek help from a specialist garage.

, the vehicle



WARNING

■

The diesel particle filter achieves very high temperatures. Therefore do not park in areas where the hot filter can come into direct contact with dry grass or other combustible materials – there is the risk of fire.

■

Always adjust your speed to suit weather, road, region and traffic conditions. The recommendations indicated by the warning light must not tempt you to disregard the national regulations for road traffic.



CAUTION

As long as the warning light  lights up, one must take into account an increased fuel consumption and in certain circumstances a power reduction of the engine.

Note

■

We recommend avoiding regularly driving short distances to assist the combus-

tion process of the soot particles in the filter.

■

Using diesel fuel with an increased sulphur content can considerably reduce the

service life of the filter. A ŠKODA Service Partner will be able to tell you which countries use diesel fuel with a high sulphur content.

■

If the engine is turned off during the filter cleaning process or shortly after-

wards, the cooling fan may turn on automatically for a few minutes.



Fuel reserve

First read and observe the introductory information and safety warnings on page 20.



The indicator light  will come on if the fuel level is less than 7 litres. An audible signal sounds as a warning signal. The following message is shown in the MAXI DOT display.

Please refuel. Range: ... km



Note

The text in the MAXI DOT display only goes out after the vehicle has been refuelled and driven a short distance.



Instruments and Indicator Lights

 Airbag system

First read and observe the introductory information and safety warnings on page 20.



If the warning light  lights up, there is a fault in the airbag system. The following message is shown in the MAXI DOT display.

Fault: Airbag



The operational capability of the airbag system is monitored electronically, even if one of the airbags is switched off.

If a front, side or head airbag or belt tensioner has been switched off using the vehicle system tester:

The  warning light comes on for around 4 seconds after the ignition is switch-

›

ed on and then flashes for approximately another 12 seconds at 2 second intervals.

The following message is shown in the MAXI DOT display.

Airbag/belt tensioner deactivated.



If the front passenger's front airbag was switched off using the key-operated switch on the side of the dash panel on the passenger side:

The  warning light comes on for around 4 seconds after the ignition has been

›

switched on. switching off the airbag is indicated in the middle of the dash panel by the light-

›

ing up of the yellow indicator light in display

    

» page 138.

WARNING

If there is a fault, have the airbag system checked immediately by a specialist garage. Otherwise, there is a risk of the airbag not being activated in the event of an accident.

The  warning light coming on indicates a fault in the system. Seek help from a specialist garage. Further information » page 176, Tyre pressure monitor.

Note

If the battery has been disconnected, the warning light  illuminates after the ignition is switched on. The warning light should go out after driving a short distance.

 Windscreen washer fluid level

First read and observe the introductory information and safety warnings on page 20.



If the windscreen washer fluid level is too low, the warning light  comes on. The following message is shown in the MAXI DOT display.

Top up wash fluid!



Top up with liquid » page 163.



Traction control (TCS) switched off

First read and observe the introductory information and safety warnings on page 20.



The ASR is switched off by pressing the button » page 112 and the warning light



illuminates.

The following message is shown in the MAXI DOT display.





Traction control (ASR) deactivated.



 Tyre pressure

First read and observe the introductory information and safety warnings on page 20.



The warning light  lights up, if there is a substantial drop in inflation pressure in one of the tyres. Check and adjust the pressure in all tyres.

Using the system

 

Turn signal system

First read and observe the introductory information and safety warnings on page 20.



Either the left  or right  warning light flashes depending on the position of the turn signal lever.



If a turn signal light fails, the warning light flashes at twice its normal rate. Switching off the hazard warning light system is switched on will cause all of the

turn signal lights as well as both warning lights to flash. Further information » page 45, Turn signal and main beam lights.



Low beam

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on when low beam is selected » page 43.

 Fog lights

First read and observe the introductory information and safety warnings on page 20.



The warning light  comes on when the fog lights are operating » page 46.



Cruise control system

First read and observe the introductory information and safety warnings



The warning light  comes on when the cruise control is operating » page 114.

 Selector lever lock



If the warning light  lights up, operate the brake pedal. This is necessary to be able to move the selector lever from position P or N » page 101.

on page 20.

First read and observe the introductory information and safety warnings on page 20.

 Main beam

First read and observe the introductory information and safety warnings on page 20.





The warning light  comes on when the main beam or headlight flasher are selected » page 45.



Instruments and Indicator Lights

Unlocking and locking

Introduction



This chapter contains information on the following subjects: Vehicle key

Replacing the battery in the remote control key 29 Child safety lock 29 Opening/closing the door 30 Locking/unlocking the vehicle without central locking 30 Emergency locking of the doors 31

Vehicle key

Fig. 8

Key: without/with remote control

First read and observe the introductory information given on page 28.



Two keys are provided with the vehicle. Depending on the equipment, your vehicle can be equipped with keys without radio remote control » Fig. 8 -  or with radio remote control» Fig. 8 - .

WARNING

■

Always withdraw the key whenever you leave the vehicle - even if it is only for a short time. This is particularly important if children are left in the vehicle. The children might otherwise start the engine or operate electrical equipment (e.g. power windows) – risk of injury.

■

Do not withdraw the ignition key from the ignition lock until the vehicle has come to a stop. You might otherwise unintentionally engage the steering lock – there is the risk of an accident.



CAUTION

■

Each key contains electronic components; therefore it must be protected

against moisture and severe shocks.

■

Keep the groove of the keys absolutely clean. Impurities (textile fibres, dust,

etc.) have a negative effect on the functionality of the locking cylinder and ignition lock.

■

Operation of the remote control may temporarily be affected by interference

from transmitters close to the car operating in the same frequency range (e.g. mobile phone, TV transmitter).

■

The battery must be replaced if the central locking only reacts to the remote

control at less than 3 metres away » page 29.

Note

Please contact a specialist garage if you lose a key as they can obtain a new one for you.



Using the system

Replacing the battery in the remote control key

Fig. 9 Remote control key: Remove cover/remove battery

First read and observe the introductory information given on page 28.



Each remote control key contains a battery located under the cover A » Fig. 9. The battery needs replacing if red indicator light » Fig. 8 on page 28 -  does not go on when you press a button on the remote control key. We recommend having key battery replaced by a specialist garage. However, if you would like to replace the discharged battery yourself proceed as follows.

Flip out the key.

›

Press off the battery cover with your thumb or using a flat screwdriver in the

›

region of arrows 1 » Fig. 9. Remove the discharged battery from the key by pressing the battery down-

›

wards in the region of arrow Insert the new battery. Ensure that the “+” symbol on the battery is facing up-

›

wards. The correct polarity is shown on the battery cover. Place the battery cover on the key and press it down until it clicks into place.

›

CAUTION

■

Pay attention to the correct polarity when changing the battery.

■

The replacement battery must have the same specification as the original bat-

tery.

For the sake of the environment

Dispose of the used battery in accordance with national legal provisions.

Note

■

The system has to be synchronised, if the vehicle cannot be unlocked or locked

with the remote control key after replacing the battery » page 35.

■

Replacing the battery in the key a glued decorative cover requires the cover to

be destroyed. A replacement cover can be purchased from a ŠKODA Partner.

Child safety lock

Fig. 10 Switching child safety lock on: for vehicles without or with central locking system

First read and observe the introductory information given on page 28.



The child safety lock prevents the corresponding rear door from being opened

from the inside. The door can only be opened from the outside.

You can switch the child safety lock on and off using the vehicle key.

Switching on

On vehicles without central locking, turn the slot of the lock in the left-hand

›

door anti-clockwise » Fig. 10 -  and clockwise in the right-hand door. On vehicles with central locking, turn the slot of the lock in the left-hand door

›

clockwise » Fig. 10 -  and anti-clockwise on the right-hand door.

Switching off

On vehicles without central locking, turn the slot of the lock on the left-hand

›

door clockwise and anti-clockwise on the right-hand door. On vehicles with central locking, turn the slot of the lock on the left-hand door

›

anti-clockwise and clockwise on the right-hand door.



Unlocking and locking

Opening/closing the door

Locking/unlocking the vehicle without central locking

Fig. 11 Door handle/door opening lever

First read and observe the introductory information given on page 28.



Opening from the outside

Unlock the vehicle and pull the door handleA » Fig. 11 on the door you wish to

›

open.

Opening from the inside

Pull on door handle B of the door and push the door away from you.

›

Closing from the inside

Grab the pull handle C and close the door.

›

WARNING

■

Make sure that the door has closed correctly as it can open suddenly while

the vehicle is being driven – there is a risk of death.

■

Only open and close the door when there is no one in the opening/closing

sweep – there is a risk of injury.

■

An opened door can close spontaneously if there is a strong wind or the ve-

hicle is on a slope – there is a risk of injury.

Using the system

Fig. 12 Securing knob in the front door/rear door

First read and observe the introductory information given on page 28.



The locking knob » Fig. 12 will move upwards or downwards when you lock or unlock the door.

Unlocking from the outside

Unlock the front door with the key » page 33.

›

Unlocking from the inside

Pull on the door opening lever.

›

Locking from the outside

Lock the front door with the key » page 33.

›

Locking from the inside

Push the locking knob » Fig. 12 down.

›

WARNING

Locked doors prevent unwanted entry into the vehicle from outside, for exam-



ple at road crossings. Locked doors do, however, make it more difficult for rescuers to get into the vehicle in an emergency – risk of death!



Note

■

Lock the opened rear doors and front passenger door by closing them and

pressing the securing knob.

■

It is not possible to lock the opened driver's door using the securing knob. This

prevents against inadvertently locking the key in the vehicle.

Emergency locking of the doors

Fig. 13

Rear door: Emergency locking of the door

First read and observe the introductory information given on page 28.



An emergency locking mechanism is located on the end face of the doors which have no locking cylinder, it is only visible after the door is opened.

Locking

Remove the cover A » Fig. 13.

›

Insert the key into the slot B and turn it into the horizontal position in the di-

›

rection of the arrow (mirror-inverted on the right doors). Replace the cover.

›

After closing the door, it no longer be opened from the outside. The door can be unlocked from the inside by pulling on the door handle again, and then opened from the outside.

Central locking system

 Introduction



This chapter contains information on the following subjects:

Individual settings

Safe securing 32

Unlocking the vehicle using the key 33

Locking the vehicle with the key 33

Vehicle locking/unlocking from the inside 33

When using central locking or unlocking, all doors are locked or unlocked simulta-

neously. The boot lid is unlocked when opening. It can be opened by pressing the

handle above the licence plate » page 37, Opening/closing.

Warning light in the driver's door

After locking the vehicle, the warning light flashes for around 2 seconds in quick

succession, afterwards it begins to flash evenly at longer intervals.

If the vehicle is locked and the safe securing system » page 32 is not operating,

the warning light in the driver door flashes for about 2 seconds fast, goes out and

starts to flash evenly at longer intervals after about 30 seconds.

If the indicator light first flashes fast for about 2 seconds, then lights up for about

30 seconds continuously and then flashes slowly, there is a fault in the central

locking system or in the interior monitor and in the towing protection » page 36.

Seek help from a specialist garage.

Convenience operation of windows

The windows can be opened and closed when unlocking and locking the vehi-

cle » page 40.

WARNING



■

Locked doors prevent unwanted entry into the vehicle from outside, for ex-

ample at road crossings.

■

The central locking system also operates if the ignition is switched off. Children should never be left unattended in the vehicle since it is difficult to provide assistance from the outside when the doors are locked. Doors locked from the inside make it difficult for rescuers to get into the vehicle in an emergency – danger to life!



Unlocking and locking

CAUTION

If the safe securing system is activated» page 32, the door opening lever and the central locking buttons do not operate.

Note

■

In the event of an accident in which the airbags are deployed, the locked doors are automatically unlocked in order to enable rescuers to gain access to the vehicle.

■

Only the driver's door can be locked or unlocked with the key if the central locking system fails. The other doors and the tailgate can be locked or unlocked manually.

■

Emergency locking of the door » page 31.

■

Emergency unlocking of the boot lid » page 38.

Individual settings

First read and observe the introductory information and safety warnings on page 31.



Opening a single door

This selection function makes it possible to only unlock the driver's door. The other doors remain locked and are only unlocked when the command is repeated.

Automatic locking and unlocking

All the doors and the boot lid are locked automatically once the car reaches a speed of about 15 km/h.

If the ignition key is withdrawn, the car is then automatically unlocked again. In addition, it is possible for the driver or front passenger to unlock the car by pressing the central locking button  » page 33.

The doors can be unlocked and opened from the inside by a single pull on the opening lever of the respective door.

Note

Individual settings can be applied in a specialist workshop.

Safe securing

First read and observe the introductory information and safety warnings on page 31.



The central locking system is equipped with a safe securing system. The door locks are blocked automatically if the vehicle is locked from the outside. The warning light flashes for around 2 seconds in quick succession, afterwards it begins to flash evenly at longer intervals. It is not possible to open the doors with the door handle either from the inside or from the outside. This acts as an effective deterrent for attempts to break into your vehicle.

The safe securing system can be deactivated within 2 seconds by double locking the vehicle.



If the safe securing system is not operating, the warning light in the driver door flashes for about 2 seconds fast, goes out and starts to flash evenly at longer intervals after about 30 seconds.

The safe securing system is activated again the next time the vehicle is unlocked and locked.

If the vehicle is locked and the safe securing system is deactivated, the door can be opened from the inside by a single pull on opening lever of the respective door.

WARNING

If the vehicle is locked from the outside and the safe securing system is activated, there must not be any person in the vehicle as it is then no longer possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emergency – risk of death.

Note

■

The anti-theft alarm system is activated when the vehicle is locked even if the safe securing system is deactivated. The interior monitor is however not activated.



■

You will be informed that the safe securing system is activated after the vehicle is locked by the CHECK DEADLOCK message on the instrument cluster display. On vehicles equipped with the MAXI DOT display, the display shows Check deadlock.

Read manual.



Using the system

Note

This function is only enabled in certain countries.

Unlocking the vehicle using the key

Fig. 14

Turning the key for unlocking and locking the vehicle

First read and observe the introductory information and safety warnings on page 31.



Turn the key in the locking cylinder of the driver's door in the direction of travel

›

(unlocking position) A » Fig. 14. Pull the door handle and open the door.

›

All the doors (only the driver's door on vehicles with anti-theft alarm system)

›

are unlocked. The boot lid is then unlocked.

›

The switched on interior lights come on over the door contact.

›

The safe securing system is deactivated.

›

The windows open while the key is held in the unlock position.

›

The warning light in the driver door stops flashing if the car is not fitted with an

›

anti-theft alarm system » page 35.

Note

If the vehicle is equipped with an anti-theft alarm system, you must insert the key into the ignition lock and switch the ignition on within 15 seconds after unlocking the door in order to deactivate the anti-theft alarm system. The alarm is trig-

gered if the ignition is not switched on within 15 seconds.

Locking the vehicle with the key



First read and observe the introductory information and safety warnings on page 31.



Turn the key in the locking cylinder of the driver's door opposite to the direction

›

of travel (locking position) B » Fig. 14 on page 33.

All the doors and the boot lid are locked.

›

The switched on interior lights will switch off over the door contact.

›

The windows and the electric sliding/tilting roof close while the key is held in

›

the lock position. The safe securing system is immediately activated.

›

The warning light in the driver door begins flashing.

›

Note

If the driver's door has been opened, the vehicle cannot be locked.

Vehicle locking/unlocking from the inside

Fig. 15

Centre console: Central locking button

First read and observe the introductory information and safety warnings



If the vehicle was not locked from the outside, you can also unlock and lock it with the rocker switch » Fig. 15 even if the ignition is not switched on.

Locking all doors and the boot lid



Press  on the button » Fig. 15. The symbol  in the button comes on.

›

on page 31.





Unlocking and locking

Unlocking all doors and the boot lid

Press  on the button » Fig. 15. The symbol  in the button is no longer illumi-

›

nated.

The following applies if your vehicle has been locked using the central locking button.

It is not possible to open the doors or the boot lid from the outside (safety fea-

›

ture, e.g. when stopping at traffic lights etc.). The doors can be unlocked and opened from the inside by a single pull on the

›

opening lever of the respective door. If at least one door has been opened, the vehicle cannot be locked.

›

In the event of an accident in which the airbags are deployed, the locked doors

›

are automatically unlocked from the inside in order to enable rescuers to gain access to the vehicle.

Note

■

The remote control is automatically deactivated when the ignition is switched on.

■

Operation of the remote control may temporarily be affected by interference from transmitters close to the car operating in the same frequency range (e.g. mobile phone, TV transmitter).

■

The battery must be replaced if the central locking or anti-theft alarm system does react to the remote control at less than 3 metres away » page 29.

■

If the driver door is open, the vehicle cannot be locked using the remote control key.



Unlocking/locking



Remote control



Introduction

This chapter contains information on the following subjects: Unlocking/locking 34

Synchronization

You can use the remote control key to:

unlock and lock the vehicle,

›

unlocking boot lid;

›

open and close the windows » page 40, Window convenience operation.

›

The transmitter with the battery is housed in the handle of the remote control key. The receiver is located in the interior of the vehicle. The operating range of the remote control key is approx. 30 m. But this range of the remote control can be reduced if the batteries are weak.

The key has a fold-open key bit which can be used for unlocking and locking the car manually and also for starting the engine.

The system must be initialised by a specialist garage if a lost key is replaced or if the receiver unit has been repaired or replaced. Only then can the remote control key be used again.

Using the system

First read and observe the introductory information given on page 34.



Unlocking the vehicle

Press button 1 » Fig. 16.

›

Locking the vehicle

Press button 3 » Fig. 16.

›

Deactivating the safe securing system

Press button 3 » Fig. 16 twice within 2 seconds. Further information » page 31.

›

Unlocking the boot lid

Press button 2 » Fig. 16. Further information » page 37.

›

Folding out the key bit

Press button 4 » Fig. 16.

›



Fig. 16

Remote control key







Folding in the key bit

Press the button 4 » Fig. 16 and fold in the key bit.

›

Unlocking

The turn signal lights flash twice as confirmation that the vehicle has been unlocked. If the vehicle is unlocked using button 1 » Fig. 16 and none of the doors or the tailgate are opened within the next 30 seconds, the vehicle is automatically locked again and the safe securing system or anti-theft alarm system is reactivated. This function is intended to prevent the car being unlocked unintentionally.

In addition, when the car is unlocked, the electrically adjustable seats and exterior mirrors move into the position assigned to this key. The stored setting of driver seat and exterior mirrors is retrieved.

Locking

The turn signal lights flash once to confirm that the vehicle has been correctly locked.

If the doors or the boot lid remain open after the vehicle has been locked, the turn signal lights do not flash until they have been closed.

WARNING

If the car is locked from the outside and the safe securing system is activated, there must not be any person in the car as it is then not possible to open either a door or a window from the inside. The locked doors make it more difficult for rescuers to get into the vehicle in an emergency – risk of death.

Note

■

Only operate the remote control when the doors and boot lid are closed and the

vehicle is in your line of sight.

■

A ŠKODA partner can also activate/deactivate the acoustic signals on vehicles

with an anti-theft alarm system.

Synchronization

First read and observe the introductory information given on page 34.



If the vehicle does not unlock when the remote control is pressed, the key may not be synchronised. This can occur when the buttons on the remote control key are pressed several times outside the operating range of the equipment or if the battery in the remote control key has been replaced.

Synchronise the key as follows.

Press any button on the remote control key.

›

Unlock the door with the key within 1 minute of pressing the button.

›

Anti-theft alarm system



Introduction

This chapter contains information on the following subjects: Operation 36

Interior monitor and towing protection

The anti-theft alarm system increases the level of protection against people seeking to break into the vehicle. The system triggers audible and visual warning signals if an attempt is made to break into the vehicle.

Note

■

The working life of the alarm siren is 5 years.

■

Before leaving the car, it must be checked that all of the windows, doors and

the electric sliding/tilting roof are properly closed to ensure the full functionality



of the anti-theft alarm system.

■

Coding of the radio remote control and the receiver unit precludes the use of

the radio remote control from other vehicles.



Unlocking and locking

Operation

First read and observe the introductory information given on page 35.



How is the alarm system activated?

The anti-theft alarm system is activated when the vehicle is locked with the radio remote control or the key in the driver's door . It is activated 30 seconds after locking the door.

How is the alarm system deactivated?

The alarm system is deactivated by pressing the  button on the remote control. The anti-theft alarm system is reactivated if the vehicle is not opened within 30 seconds after transmitting the radio signal.

If the vehicle is unlocked by inserting the key into the driver door, the key must be inserted into the ignition lock and the ignition switched on within 15 seconds of unlocking the door to deactivate the alarm system. The alarm is triggered if the ignition is not switched on within 15 seconds.

When is the alarm triggered?

The following security areas of the locked vehicle are monitored:

bonnet;

›

boot lid;

›

doors;

›

ignition lock;

›

Vehicle inclination » page 36;

›

Interior of the vehicle » page 36;

›

A drop in voltage of the on-board power supply;

›

Socket of the factory-fitted towing device.

›

An alarm is immediately triggered if either of the two battery terminals is disconnected while the anti-theft alarm system is activated.

How is the alarm switched off?

The alarm is turned off by pressing the  button on the remote control key or switching the ignition on.

Interior monitor and towing protection

Fig. 17

Button for interior monitor and towing protection

First read and observe the introductory information given on page 35.



The interior monitor detects movements inside the car and then triggers the alarm.

Switching off

Switch off the ignition.

›

Open the driver door.

›

Press the  » Fig. 17 button in the driver's door.

›

Lock the vehicle within 30 seconds.

›

The interior monitor and the towing protection are switched on again automatically the next time the car is locked.

Note

■

Switch off the interior monitor and the towing protection if there is a possibility of the alarm being triggered by movements from (e.g. children or animals) within the vehicle interior or if the vehicle has to be transported (e.g. by train or ship) or towed.

■

The opened glasses storage compartment reduces the effectiveness of the interior monitor. To ensure the full functionality of the interior monitor, the glasses



storage compartment must always be closed before locking the vehicle.



Using the system

Tailgate

 Introduction

This chapter contains information on the following subjects: Opening/closing

Automatic locking 37 Emergency unlocking 38

WARNING

■

Ensure that the lock is properly engaged after closing the boot lid. Otherwise, the tailgate might open suddenly while the vehicle is moving if it was locked – risk of an accident.

■

Never drive with the tailgate fully opened or slightly ajar otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning.

■

Do not press on the rear window when closing the tailgate, as otherwise this could crack – there is a risk of injury.

Note

■

After closing the boot lid, it is automatically locked within 1 second and the

anti-theft alarm system is activated. This applies only if the vehicle was locked

before closing the boot lid.

■

The function of the handle above the licence plate is deactivated when starting

off or at a speed of 5 km/hour or more for vehicles with central locking. The function of the handle is activated again when the vehicle has stopped and a door is opened.

Opening/closing

Fig. 18 Unlock the boot lid/boot lid handle

First read and observe the introductory information and safety warnings



After unlocking the vehicle, you can open the lid by pushing the handle located above the licence plate.

Opening the boot lid for vehicles without central locking

Press the  button in the driver's door » Fig. 18 -  and open the tailgate in

›

the direction of the arrow » Fig. 18 - .

Opening the boot lid for vehicles with central locking

Press the handle and open the tailgate in the direction of the arrow » Fig. 18 -

›



Closing



Pull down the tailgate and close it with a gentle swing.

›

A handle which makes the closing easier is located on the inner panelling of the boot lid.

on page 37.

Automatic locking

First read and observe the introductory information and safety warnings on page 37.



If the vehicle was locked before the tailgate was closed, the lid is locked automatically immediately it is closed.





Unlocking and locking

The period after which the tailgate locks automatically can be extended by a specialist garage.

Delayed locking

If the tailgate was opened with the  button on the remote control key, then it is possible to open the lid within a limited period of it being closed.

There is a risk of unwanted entry into the vehicle before the boot lid is locked automatically. Therefore always lock the vehicle with the  button on the remote control.

Delayed locking can be disabled by a specialist garage at any time.

Note

More detailed information is available from a ŠKODA Partner.

Emergency unlocking

Fig. 19

Emergency unlocking of the boot lid

First read and observe the introductory information and safety warnings on page 37.



The boot lid can be unlocked manually if there is a fault in the central locking system.

Unlocking

Fold the rear seat backrest forward » page 56, Rear seats.

›

Insert a screwdriver or similar tool into the opening in the trim in the direction

›

of the arrow 1 » Fig. 19 as far as the stop. Unlock the lock 3 under the trim in the direction of arrow 2.

›

Open the tailgate.

›

Electrical power windows

 Introduction

This chapter contains information on the following subjects: Opening/closing the windows

Power window force limiter 39 Window convenience operation 40 Operational faults 40

WARNING



■

If the vehicle is locked from the outside, do not leave anybody in the vehicle as it is not possible to open the windows from the inside in the event of an emergency.

■

The system is fitted with a force limiter » page 39. If there is an obstacle, the closing process is stopped and the window goes down by several centimetres. The windows should nevertheless be closed carefully – risk of injury.

■

It is recommended that the power windows in the rear doors are deactivated (safety switch) S » Fig. 20 on page 39 when children are being transported on the rear seats.

■

Proceed with caution when closing windows to avoid causing crushing injuries - there is a risk of injury.

CAUTION

■

Keep the windows clean to ensure the correct functionality of the electric win-

dows.

■

Should the windows freeze, first remove the ice » page 153, Windows and ex-

terior mirrors and only then operate the power windows. Otherwise, the window

seal and the power window mechanism could be damaged.

■

In the winter, ice on the window may cause greater resistance as the window is

closed. The window will stop and open again by several centimetres.

■

Always make sure that the windows are closed when you leave the locked vehi-

cle.



For the sake of the environment

At high speeds, you should keep the windows closed to prevent unnecessarily high fuel consumption.



Using the system

Note

■

After switching the ignition off, it is still possible to open or close the windows for approx. 10 minutes. The electrical power windows are only switched off completely once the driver's door or front passenger door are opened.

■

When driving always use the existing heating, air conditioning and ventilation system for ventilating the interior of the vehicle. If the windows are opened, dust as well as other dirt can get into the vehicle and in addition the wind noise is more at certain speeds.

Opening/closing the windows

Buttons on the driver's door/in the rear doors

Fig. 20

First read and observe the introductory information and safety warnings on page 38.



Power window buttons » Fig. 20.

Button for electrical power window of the driver's door

Button for electrical power window of the front passenger door

Button for electrical power window of the rear right door

Button for electrical power window of the rear left door

Safety pushbutton

The electrical power windows can only be operated when the ignition is switched on.

Opening

A window is opened by pressing lightly on the relevant button. The opening

›

process stops when one releases the button.

The window will also open fully automatically if you briefly press the button as far as the stop. Renewed pressing of the button causes the window to stop immediately.

Closing

The window is closed by pulling lightly on the relevant button. The closing proc-

›

ess stops when one releases the button.

The window will also close fully automatically if you briefly pull the button as far



as the stop. Renewed pulling of the button causes the window to stop immediately.

Safety pushbutton

The buttons for power windows in the rear doors can be deactivated by pressing the safety switch rear doors are activated again by pressing the safety pushbutton S again.

If the buttons for the rear doors are deactivated, the warning light  in the safety switch S lights up.

» Fig. 20. The buttons for the electrical power windows in

Note

The window lift mechanism is equipped with protection against overheating. Repeated opening and closing of the window can cause this mechanism to overheat. If this happens, it will not be possible to operate the window for a short time. You will be able to operate the window again as soon as the overheating protection has cooled down.

Power window force limiter

First read and observe the introductory information and safety warnings on page 38.



The electrical power windows are fitted with a force limiter. It reduces the risk of bruises or injuries when closing the windows.

If there is an obstacle, the closing process is stopped and the window goes down by several centimetres.

If the obstacle prevents the window from being closed during the next 10 seconds, the closing process is interrupted once again and the window goes down by several centimetres.





Unlocking and locking

If you attempt to close the window again within 10 seconds of the window being moved down for the second time, even though the obstacle was not yet been removed, the closing process is only stopped. During this time it is not possible to automatically close the window. The force limiter is still switched on.

The force limiter is only switched off if you attempt to close the window again within the next 10 seconds - the window will now close with full force!

If you wait longer than 10 seconds, the force limiter is switched on again.

Window convenience operation

First read and observe the introductory information and safety warnings



The electrical power windows can be opened and closed as follows when unlocking and locking the vehicle.

Opening

Press the  button on the remote control key and hold.

›

Hold the key in the driver's lock in the unlock position.

›

Hold button

›

Closing

Press the  button on the remote control key and hold.

›

Hold the key in the driver's lock in the lock position.

›

Hold button

›

You can interrupt the opening or closing process for the windows immediately by releasing the key or the lock button.

on page 38.

in the opening position » Fig. 20 on page 39.

in the closing position » Fig. 20 on page 39.

Operational faults

First read and observe the introductory information and safety warnings on page 38.



Electrical power windows do not operate

If the battery has been disconnected and then reconnected while the window



was opened, the electrical power windows will not operate. The system must be activated. Proceed as follows to re-establish the function.

Switch on the ignition.

›

Pull the top edge of the button in the driver's door and close the window.

›

Release the button.

›

Pull the relevant button upwards again for another approximately 3 seconds

›

and hold.

Operation in winter

In the winter, ice on the window may cause greater resistance as the window is closed. The window will stop and open again by several centimetres.

It is necessary to deactivate the force limiter to close the window » page 39.

Electric sliding/tilting roof



Introduction

This chapter contains information on the following subjects:



Operation 41 Comfort operation Emergency operation

The sliding/tilting roof is operated with the rotary switch » Fig. 21 on page 41 and only works when the ignition is switched on. The control dial has several positions.

The sliding/tilting roof can still be opened, closed and tilted for approx. 10 minutes after switching the ignition off. However, as soon as one of the front doors is opened it is no longer possible to operate the sliding/tilting roof.





Convenience opening and closing the windows with the button Ais possible immediately after unlocking the vehicle or turning off the ignition and opening the driver's or front passenger's door.

Using the system

WARNING

Close the sliding/tilting roof carefully – risk of injury.

CAUTION

During the winter it may be necessary to remove any ice and snow in the vicinity of the sliding/tilting roof before opening it to prevent any damage to the opening mechanism and seal.

Note

If the battery has been disconnected and reconnected, it is possible that the sliding/tilting roof does not close fully. This is why the rotary switch must be set to position A » Fig. 21 on page 41 and pressed forwards for about 10 seconds.

Operation

Closing

Turn the switch to position A » Fig. 21.

›

Force limiter

The sliding/tilting roof is fitted with a force limiter. If an obstacle (e.g. ice) prevents closing, the sliding/tilting roof stops and opens completely. The sliding/tilting roof can be closed completely without the force limiter by pushing the switch in position A » Fig. 21 forwards until the sliding/tilting roof is completely closed » page 41, in section Introduction.

When the sliding/tilting roof is in the comfort position, the intensity of the wind noise is much less.

The sun screen is also opened automatically when the roof slides open.



Note

When the sliding/tilting roof is in the comfort position, the intensity of the wind noise is reduced.



Fig. 21

Control dial for the power sliding/tilting roof

First read and observe the introductory information and safety warnings on page 40.



Comfort position

Turn the switch to position C » Fig. 21.

›

Open fully

Turn the switch to position B » Fig. 21 and hold it in this position (spring-loaded

›

position).

Tilting roof

Turn the switch to position D » Fig. 21.

›

Comfort operation

First read and observe the introductory information and safety warnings on page 40.



An open sliding/tilting roof can also be closed from the outside.

Press the  button on the remote control key and hold or hold the key in the

›

lock cylinder of the driver's door in the locked position » .

The closing operation stops immediately when you release the key or the lock button.

WARNING

Close the sliding/tilting roof carefully – risk of injury. The force limiter does not operate with the convenience closing.

Unlocking and locking



Emergency operation

Fig. 22 Point for positioning screwdriver/opening for positioning the key

First read and observe the introductory information and safety warnings



The sliding/tilting roof can be closed or opened manually if the system is faulty. The emergency operation of the sliding roof is located underneath the glasses storage box

Open the glasses storage box.

›

Carefully insert an approximately 5 mm wide screwdriver into the slot in the po-

›

sitions shown by the arrows Carefully fold the glasses storage box downwards by gently pressing down and

›

turning the screwdriver. Insert an Allen key, SW 4, up to the stop into the opening 2 and close or open

›

the sliding/tilting roof. Reinstall the glasses storage box by first inserting the plastic plugs and then

›

pushing the entire part upwards.

on page 40.

» page 74, Glasses storage box.

» Fig. 22.

Note

It is necessary after each emergency operation (using the Allen key) to move the sliding/tilting roof into the basic position. This is why the rotary switch must be set to position A » Fig. 21 on page 41 and pressed forwards for about 10 seconds.



Using the system

Lights and visibility

Lights

Introduction



This chapter contains information on the following subjects: Parking and low beam lights

Headlight beam adjustment 44 Daylight running lights (DAY LIGHT) 44 Turn signal and main beam lights 45 Halogen projector headlights with cornering light function 45 Fog lights 46 Foglights with the CORNER function Rear fog light 46 Tourist lights Hazard warning light system Parking lights 47

The lights work only with the ignition on, unless otherwise stated.

The layout of the controls on right-hand drive vehicles partially differs from that shown in » Fig. 23 on page 43. The symbols which mark the positions of the controls are identical.

WARNING

■

Never drive with only the side lights on! The side lights are not bright enough to light up the road sufficiently in front of you or to be seen by other oncoming traffic. Therefore always switch on the low beam when it is dark or if visibility is poor.

■

The activation of the lights should only be undertaken in accordance with national legal requirements.

■

The driver is always responsible for the correct settings and use of the lights.

46 47

Note

The headlights may mist up temporarily. When the driving lights are switched on, the light outlet areas are free from condensation after a short time, although the headlight lenses may still be misted up around the edge. This mist has no influence on the life of the lighting system.

Parking and low beam lights

Fig. 23

Dash panel: Light switch

First read and observe the introductory information and safety warnings on page 43.



Light switch positions » Fig. 23.

Switch on the parking light or parking lights on both sides » page 47



Switch on low beam

 

Switching off lights (except daytime running lights) Switch on the front fog lights » page 46



Switch on the rear fog lights » page 46



Note

■

An audible warning signal will sound if the light switch is in the  or  position, the ignition key is removed and the driver's door is opened. The audible warning signal is switched off by means of the door contact when the driver's door is closed (ignition off), however, the side lights remain on to illuminate the parked vehicle if necessary.

■

Always turn the light switch to the 0 position if you are leaving the vehicle and don't want to use the parking light.



Lights and visibility

Headlight beam adjustment

Fig. 24

Dash panel: Lights and visibility

First read and observe the introductory information and safety warnings on page 43.



Turning the rotary switch » Fig. 24 from position  to  gradually adjusts the headlight beam thereby shortening the beam of light.

The positions of the rotary switch correspond approximately to the following car load.

Front seats occupied, boot empty.



All seats occupied, boot empty.

 

All seats occupied, boot loaded. Driver seat occupied, boot loaded.



WARNING

Always adjust the headlight beam to satisfy the following conditions.

■

The vehicle does not dazzle other road users, especially oncoming vehicles.

■

The beam range is sufficient for safe driving.

Note

We recommend you adjust the headlight beam when the low beam is switched on.

Daylight running lights (DAY LIGHT)

First read and observe the introductory information and safety warnings on page 43.



Switching on the daytime running lights

Turn the light switch to position 0 » Fig. 23 on page 43.

›

Activating/deactivating the daytime running lights function

Activate and deactivate the daytime running lights by fitting/removing the fuse

›

with the appropriate ampere rating for daytime running lights » page 193, Fuses in the dash panel.

Deactivating on vehicles with the START-STOP system

Switch off the ignition.

›

At the same time, pull the turn signal light stalk » Fig. 25 on page 45 towards

›

the steering wheel, push it downwards, and hold it in this position. Switch on the ignition - wait until the left-turn signal light flashes 4x.

›

Switch off the ignition - an audible signal sounds which confirms the deactiva-

›

tion of the daylight driving lights. Release the turn signal stalk.

›

Activating on vehicles with the START-STOP system

Switch off the ignition.

›

At the same time, pull the turn signal light stalk » Fig. 25 on page 45 towards

›

the steering wheel, push it upwards, and hold it in this position. Switch on the ignition - wait until the right-turn signal light flashes 4x.

›

Switch off the ignition - an audible signal sounds which confirms the activation

›

of the daylight driving lights. Release the turn signal stalk.

›

On vehicles with separate lights for daylight driving lights in the fog lights or in the front bumper, the parking lights and the licence plate light do not come on when activating the function daylight driving lights (neither front nor rear).

If the vehicle is not equipped with separate lights for daylight driving lights, the combination of the low beam, the parking lights (front and rear) including the licence plate light is used as daylight driving lights.



Note

In vehicles with separate lights for daylight driving lights (in the bumper below the main headlights) these lights also serve as side lights.



Using the system

Turn signal and main beam lights

Fig. 25

Stalk: turn signal and main beam operation

First read and observe the introductory information and safety warnings on page 43.



The parking light is controlled with the control stalk » page 47.

Control stalk positions » Fig. 25.

Switch on right turn signal

Switch on left turn signal

Switch on high beam (spring-loaded position)

Switch off main beam and headlamp flasher (spring-loaded position)

When the left or right turn signal is on, the  or  warning light flashes in the instrument cluster.

When the high beam or headlight flasher is on, the  warning light lights up in the instrument cluster.

Turn signal for changing lanes - to flash only briefly, move the stalk up or down to the pressure point only and hold it in this position.

Convenience turn signal

If you wish to flash three times only, briefly push the stalk to the upper or lower pressure point and release again.







Note

■

The main beam can only be switched on when the low beam lights are on.

■

The headlight flasher can be operated even if the ignition is switched off.

■

The turn signal system only operates when the ignition is switched on.

■

The turn signal is automatically cancelled after negotiating a curve.

■

The warning light flashes at twice its normal rate if a bulb for the turn signal light fails.

Halogen projector headlights with cornering light function

First read and observe the introductory information and safety warn-

on page 43.

ings



For a better cornering illumination, the halogen projector headlights with cornering light function are set in the optimal position in line with the vehicle speed and the steering angle.

WARNING

If the halogen projector headlights with cornering light function are faulty, the

headlights are automatically lowered to the emergency position, which pre-

vents a possible dazzling of oncoming traffic. Thus the illuminated length of

the road is shortened. Drive carefully and visit a specialist garage as soon as

possible.



WARNING

Only turn on the main beam or the headlight flasher if other road users will not be dazzled.

Lights and visibility

Fog lights

Fig. 26

Dash panel: Light switch

First read and observe the introductory information and safety warnings on page 43.



Switching on/off

First turn the light switch » Fig. 26 to position  or .

›

Pull the light switch to position 1.

›

The rear fog light is switched off in the reverse sequence.

The warning light  lights up in the instrument cluster when the fog lights are switched on » page 20.

The daytime running lights are not switched on.

›

The fog lights are not switched on.

›

Reverse gear is not engaged.

›

Rear fog light

First read and observe the introductory information and safety warnings on page 43.



Switching on/off

First turn the light switch » Fig. 26 on page 46 to position  or .

›

Pull the light switch to position 2.

›

The rear fog light is switched off in the reverse sequence.

If the vehicle is not fitted with fog lights » page 46, the rear fog light is switched on by turning the light switch to the position  or  and is pulled out directly to the position 2. This switch can only be pulled into one position.

The warning light  lights up in the instrument cluster when the rear fog light is switched on » page 20.

Only the rear fog light on the trailer lights up if the vehicle has a factory-fitted towing device or a towing device from ŠKODA original accessories and it is driven



with a trailer.



Foglights with the CORNER function

First read and observe the introductory information and safety warnings



The CORNER function lights the front fog lamp on the relevant side of the vehicle to illuminate the area around the vehicle when turning, parking, etc.

The CORNER function is switched on automatically if the following conditions are met.

The turn signal is switched on or the front wheels are turned sharply to the

›

right or left1). The engine is running.

›

The vehicle is stopped or is travelling at a speed of no more than 40 km/h.

›

The low beam is switched on.

›

If both switch on versions are conflicting, for example if the steering wheel is turned to the left and the right turn signal light is switched on, the turn signal light has the higher priority.

on page 43.

Using the system

Tourist lights

First read and observe the introductory information and safety warn-

on page 43.

ings



Halogen projector headlights with cornering light function

This mode makes it possible to drive in countries with opposing traffic system (driving on the left/right) without dazzling the oncoming vehicles. When the mode “tourist light” is active, the side to side swivel of the headlights is deactivated.

Activating tourist light

Before activating the tourist light, the following conditions must be met.



Ignition switched off, light switched off (light switch in position 0), control dial for headlamp beam adjustment in the  position, no gear engaged or selector lever in the N position (automatic gearbox), tourist light deactivated.

Switch on the ignition.

›

Within 10 seconds of the ignition being switched on:

Turn the light switch to the  position » page 43, Parking and low beam lights.

›

Engage reverse gear (manual gearbox) or move the selector lever to the R posi-

›

tion (automatic gearbox), Turn the headlamp beam adjustment dial from  to  » page 44.

›

Deactivating tourist light

Before deactivating the tourist light, the following conditions must be met. Ignition switched off, light switched off (light switch in position 0), control dial for

headlamp beam adjustment in the  position, no gear engaged or selector lever in the N position (automatic gearbox), tourist light activated.

Switch on the ignition.

›

Within 10 seconds of the ignition being switched on:

Turn the light switch to the  position » page 43, Parking and low beam lights.

›

Engage reverse gear (manual gearbox) or move the selector lever to the R posi-

›

tion (automatic gearbox), Turn the headlamp beam adjustment dial from  to  » page 44.

›

Further information » page 110, Headlights.

Note

When the “tourist light” mode is active, the warning light  flashes for 10 seconds each time the ignition is switched on.

Hazard warning light system

Fig. 27

Dash panel: Hazard warning light system button

First read and observe the introductory information and safety warnings on page 43.



Press the  » Fig. 27 button.

›

All the turn signal lights on the vehicle flash at the same time when the hazard warning light system is switched on. The warning light for the turn signals and the warning light in the button also flash at the same time. The hazard warning light system can also be operated if the ignition is switched off.

The hazard warning light system will switch on automatically if one of the airbags is deployed.

CAUTION

Switch on the hazard warning light system if, for example, the following occurs.

■

You encounter a traffic jam.

■

The vehicle has broken down.



Parking lights

First read and observe the introductory information and safety warnings on page 43.



Switching on the parking light

Switch off the ignition.

›

Pull the turn signal stalk » Fig. 25 on page 45 upwards or downwards - the side

›

light on the right or left side of the vehicle is switched on.







Lights and visibility

Switching on the side lights on both sides 

Turn the light switch » Fig. 23 on page 43 to the  position and lock the vehi-

›

cle.

Note

■

The parking light  can only be activated if the ignition is switched off.

■

If the right or left turn signal light has been switched on and the ignition is

switched off, the parking light is not automatically switched on.

Interior lights



Introduction

This chapter contains information on the following subjects: Interior lighting - version 1

Interior lighting - version 2 49 Rear interior light Illuminated storage compartment on the passenger side 49 Luggage compartment light

Interior lighting - version 1

Fig. 28

Interior lighting – version 1

First read and observe the introductory information given on page 48.



Positions of sliding switch A » Fig. 28.

Switch on



Switch off (middle position)



Control by the door contact switch





The reading lights can be turned on or off by pressing switch B » Fig. 28.

If control of the lights by the door contact switch is enabled (switch A » Fig. 28 is in the  position), the light will come on when one of the following occurs.

The vehicle is unlocked.

›

One of the doors is opened.

›

The ignition key is removed.

›

If control of the lights by the door contact switch is enabled (switch the  position), the light will go off when one of the following occurs.

The vehicle is locked.

›

The ignition is switched on.

›

About 30 seconds after all the doors have been closed.

›

If a door remains open, or if switch light goes out after 10 minutes to prevent the vehicle battery from discharging.



» Fig. 28is in the  position, the interior

» Fig. 28 in



Using the system

Interior lighting - version 2

Fig. 29

Interior lighting – version 2

First read and observe the introductory information given on page 48.



Slide switch positions » Fig. 29.

Switch on



Switch off



Control by the door contact switch (middle position)



The same principles apply for interior lighting version 2 as for » page 48, Interior lighting - version 1.

Rear interior light

Fig. 30

Interior lights at the rear

Illuminated storage compartment on the passenger side

First read and observe the introductory information given on page 48.



When opening the flap of the storage compartment on the front passenger side

›

the lighting in the storage compartment comes on.

The light switches on automatically when the parking light is switched on and

›

goes out when the flap is closed.

Luggage compartment light

First read and observe the introductory information given on page 48.



The light comes on automatically when the boot lid is opened. If the tailgate remains open for more than 10 minutes, the luggage compartment light switches off automatically.

Visibility





Introduction

This chapter contains information on the following subjects: Rear window heating

Sun visors

50 50



First read and observe the introductory information given on page 48.



Press the switch » Fig. 30 to turn the light on or off.



Lights and visibility

Rear window heating

Sun visors

Fig. 31

Button for rear window heater

First read and observe the introductory information given on page 49.



The rear window heater is switched on or off by pressing the  button » Fig. 31,

›

the warning light in the switch comes on or goes out.

The rear window heater can only be switched on when the engine is running. The rear window heater switches off automatically after approximately 7 mi-

nutes.

For the sake of the environment

The heating should be switched off as soon as the window is de-iced or free from mist. The reduced current consumption will have a favourable effect on fuel economy » page 107, Saving electrical energy.

Note

If the on-board voltage drops, the rear window heater switches off automatically, in order to provide sufficient electrical energy for the engine control » page 172, Automatic load deactivation.

Fig. 32

Sun visor: swivelling out

First read and observe the introductory information given on page 49.



The sun visor for the driver or front passenger can be pulled out of the fixture and swivelled towards the door in the direction of arrow 1 » Fig. 32.

The vanity mirrors in the sun visors are provided with covers. Push the cover in the direction of the arrow 2.

The purpose of the strap

WARNING

The sun visors must not be swivelled towards the side windows in the deployment area of the head airbags if any objects, such as ball-point pens, etc. are attached to them. This might result in injuries to the occupants if the head airbag is deployed.

Windscreen wipers and washers





Introduction

This chapter contains information on the following subjects: Windscreen wiper and washer 51

Headlight cleaning system 52 Replacing the windscreen wiper blades Replacing the rear window wiper blade

is to store small, light objects, such as a notepad, etc.





Using the system

The windscreen wipers and the windscreen washer system only operate when the ignition is switched on.

The rear window is wiped once automatically if the windscreen wipers are on when reverse gear is selected.

Top up with windscreen wiper fluid » page 163.

WARNING

■

Properly maintained windscreen wiper blades are essential for clear visibility

and safe driving » page 52.

■

Do not use the windscreen washer system at low temperatures, without heating the windscreen beforehand. Otherwise the window cleaner could freeze on the windscreen and restrict the view to the front.

■

Replace the windscreen wiper blades once or twice a year for safety reasons. These can be purchased from a ŠKODA Partner.

CAUTION

■

In cold temperatures and during the winter, check before the journey or before

switching on the ignition that the wiper blades are not frozen to the windscreen. If the windscreen wipers are switched on when the blades are frozen to the windscreen, this may damage both the blades and windscreen wiper motor!

■

If the ignition is switched off while the windscreen wipers are switched on, the

windscreen wipers will continue wiping in the same mode after the ignition is turned back on. The windscreen wipers could freeze up in cold temperatures between the time the ignition was turned off and when it was turned back on again.

■

Carefully detach frozen wiper blades from the front or rear window.

■

Remove snow and ice from the windscreen wipers before driving.

■

If the windscreen wipers are handled carelessly, there is a risk of damage to the

windscreen.

Note

■

The windscreen washer nozzles for the windscreen are heated when the en-

gine is running and the outside temperature is less than approx. +10 °C.

■

The content of the windscreen washer fluid reservoir is 3.5 litres. On vehicles

fitted with the headlight cleaning system, the volume is around 5.4 litres.

■

The wiper blades should be cleaned on a regular basis with a windscreen clean-

er to avoid any smears. The wiper blades should be cleaned with a sponge or cloth if they are heavily soiled by insect residues, for example.

Windscreen wiper and washer

Fig. 33

Operating stalk: Windscreen wipers and washer settings

First read and observe the introductory information and safety warnings on page 50.



Control stalk positions » Fig. 33.

Wipers off

Interval windscreen wiping

Slow windscreen wiping

Rapid windscreen wiping

Single windscreen wipe (spring-loaded position)

Automatic wipe/wash for windscreen (spring-loaded position)

Wiping the rear window (the wiper wipes at regular intervals after a few seconds)

Automatic wipe/wash for the rear window (spring-loaded position)

Switch for setting the desired interval between the individual windscreen

wipes (

Automatic wipe/wash for windscreen

The wash system operates immediately, the windscreen wipers wipe somewhat later.

Releasing the lever will stop the windscreen washer while the wipers continue for another 1 to 3 wiper strokes (depending on the period the windscreen has been sprayed).

Automatic wipe/wash for the rear window

The wash system operates immediately, the wiper wipes somewhat later.



Releasing the lever will stop the washer while the wipers continue for another 1 to 3 wiper strokes (depending on the period the window has been sprayed). The lever will stay in position after releasing it

Interval windscreen wiping)



Lights and visibility

Headlight cleaning system

First read and observe the introductory information and safety warnings on page 50.



The headlights are sprayed briefly if the low beam or main beam are switched on and the windscreen wiper stalk is pulled to position 5 » Fig. 33 on page 51. To clean the headlights, the windshield is also sprayed after every five squirts.

You should remove stubborn dirt (such as insect residues) from the headlight lenses at regular intervals, for example when refuelling. The following guidelines must be observed » page 154, Headlight lenses.

To ensure the proper operation of the cleaning system during the winter, any snow should be removed from the washer nozzle fixtures and ice should be cleared with a de-icing spray.

Fitting the wiper blade

Push the wiper blade in until it latches on the stop.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arms back to the windscreen.

›

Windshield wiper blades in proper condition are essential to obtain good visibility. Wiper blades should not be allowed to become dirtied by dust, insect remains and preserving wax.

Juddering or smearing of the wiper blades could then be due to wax residues left on the windshield by vehicle washing in automatic vehicle wash systems. It is therefore important to degrease the lips of the windshield wiper blades after every pass through an automatic vehicle wash system.

Replacing the rear window wiper blade



CAUTION

Never remove the nozzles from the headlight cleaning system by hand – there is risk of damage.

Replacing the windscreen wiper blades

Fig. 34

Windscreen wiper blade

First read and observe the introductory information and safety warnings on page 50.



Removing the wiper blade

Lift the windscreen wiper arm away from the windscreen.

›

Press the locking button 1 » Fig. 34 and remove the wiper blade in the direc-

›

tion of arrow 2.

Using the system

Fig. 35

Rear window wiper blade



First read and observe the introductory information and safety warnings



Removing the wiper blade

Raise the wiper arm away from the window » Fig. 35.

›

Tilt the wiper blade to the stop in the direction of the wiper arm.

›

Hold the upper part of the wiper arm and unlock the securing mechanism 1.

›

Remove the wiper blade in the direction of the arrow 2.

›

Fitting the wiper blade

Push the wiper blade in until it latches on the stop.

›

Check that the wiper blade is correctly attached.

›

Fold the wiper arm back to the windscreen.

›

on page 50.



Rear window

Exterior mirrors

 Introduction

This chapter contains information on the following subjects: Manually dimmed rear-view mirror

Exterior mirrors 53

WARNING

■

Make sure that the mirror is not covered by ice, snow, condensation or other objects.

■

Convex (curved outward) or aspheric exterior mirrors increase the field of vision. They do, however, make objects appear smaller in the mirror. These mirrors are therefore only of limited use for estimating distances to the following vehicles.

■

Whenever possible use the interior mirror for estimating the distances to the following vehicles.

Manually dimmed rear-view mirror

First read and observe the introductory information and safety warnings on page 53.



Basic setting

Pull the lever on the lower edge of the mirror away from the windscreen.

›

Dimming mirror

Push the lever on the lower edge of the mirror towards the windscreen.

›

Fig. 36

Inner part of door: Knob for the mirrors

First read and observe the introductory information and safety warnings on page 53.



The mirror can be adjusted to the desired position by moving the knob in the direction of the arrow » Fig. 36.



The movement of the mirror surface follows the movement of the rotary knob.

The knob can be moved into the following positions.

Adjust the left mirror



Adjust the right mirror

 

Switch off mirror control Mirror heater



Folding in the exterior mirrors

The whole exterior mirror can be manually folded towards the side windows. Restore it to its original position, it should be folded back from the side window until it audibly clicks into place.



Note

■

The exterior mirror heater only operates when the engine is running.

■

Do not touch the surface of the exterior mirrors if the exterior mirror heater is

switched on.

■

If the power setting function fails at any time, the exterior mirrors can be set by

hand by pressing on the edge of the mirror surface.

■

Contact your specialist garage if there is a fault with the electrical adjustment

of the exterior mirrors.



Lights and visibility

Seats and storage

Front seats

Introduction



This chapter contains information on the following subjects: Adjusting the front seats - Version 1

Adjusting the front seats - Variant 2 55 Front seat heating 55

The driver's seat should be adjusted in such a way that the pedals can be fully pressed to the floor with slightly bent legs.

The seat backrest on the driver's seat should be adjusted in such a way that the upper point of the steering wheel can be easily reached with slightly bent arms.

Correct adjustment of the seats is particularly important:

for reaching the controls safely and quickly;

›

for a relaxed, fatigue-free body position;

›

for achieving maximum protection from the seat belts and the airbag system.

›

WARNING

General information

■

Caution when adjusting the seat! You may suffer injuries or bruises as a re-

sult of adjusting the seat without paying proper attention.

■

The seat backrests must not be reclined too far when driving otherwise this will affect proper operation of the seat belts and of the airbag system – risk of injury.

■

Never carry more people than the number of seats in the vehicle.

■

Each occupant must correctly fasten the seat belt belonging to the seat. Children must be fastened » page 140, Transporting children safely with a suitable restraint system.

■

The front seats and head restraints must be adjusted to match the body size at all times and the seat belt must always be fastened properly to provide the most effective levels of protection to the passengers.

■

Do not transport any objects on the front passenger seat other than objects (e.g. child safety seat) intended for this purpose – there is the risk of an accident.

WARNING

Information for the driver

■

Only adjust the driver's seat when the vehicle is stationary – there is the risk

of an accident.

■

Keep a distance of at least 25 cm from the steering wheel. Not keeping to this minimum distance will mean that the airbag system will not be able to properly protect you – risk of death.

■

Ensure that there are no objects in the driver's footwell as they may get

caught behind the pedals while you are driving or under braking. You would then no longer be able to operate the clutch, brake or accelerate.

WARNING

Information for the front seat passenger

■

Maintain a distance of at least 25 cm from the dash panel. Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you - there is a risk that you could be killed.

■

Always keep your feet in the footwell when the car is being driven - never place your feet on the instrument panel, out of the window or on the seats. You will be exposed to increased risk of injury if it becomes necessary to apply the brakes or in the event of an accident. You may suffer fatal injuries when an airbag is deployed if you have adopted an incorrect seating position.

Note

After a certain time, play can develop within the adjustment mechanism of the backrest angle.



Using the system

Adjusting the front seats - Version 1

Fig. 37

Control elements on the seat

First read and observe the introductory information and safety warnings on page 54.



Adjusting a seat fore and aft

Pull lever 1 » Fig. 37 up and push the seat into the desired position.

›

Release the lever 1 and push the seat until the lock clicks into place.

›

Adjusting height of seat

To lift the seat, pull or pump lever 2 » Fig. 37 upwards.

›

To lower the seat, push or pump the lever 2 downwards.

›

Adjusting the angle of the seat backrest

To adjust the angle of the backrest, relieve any pressure from the seat backrest

›

(do not lean on it) and turn handwheel 3 » Fig. 37.

Adjusting the front seats - Variant 2

First read and observe the introductory information and safety warnings on page 54.



Adjusting a seat fore and aft

Pull the lever (in the middle) 1 » Fig. 38 up and push the seat to the desired

›

position. Release the lever 1 and push the seat until the lock clicks into place.

›

Adjusting height of seat

To lift the seat, pull or pump lever 2 » Fig. 38 upwards.

›

To lower the seat, push or pump the lever 2 downwards.

›

Adjusting the angle of the seat backrest

Relieve the load on the seat backrest (do not lean on it), pull the lever

›

» Fig. 38 towards the rear and set the desired angle of the seat backrest with the back. After releasing the lever 3, the seat backrest will remain in the set position.

›

Front seat heating

Fig. 39

Rocker switch for front seat heating



Fig. 38

Control elements on the seat

First read and observe the introductory information and safety warnings on page 54.



The seat backrests and seats can be heated electrically.

Switch the front seat heating to 25 % or 100 % power by pressing rocker switch

›

at position 1 or 2 » Fig. 39. To switch off the heating shift the rocker switch into the horizontal position.

›

Seats and storage



WARNING

If, as an occupant, you have a subdued pain and/or temperature sensitivity, e.g. through medication, paralysis or because of chronic illness (e.g. diabetes), we recommend not to use the seat heating. This can lead to burns on the back, the posterior and the legs which are difficult to heal. If the seat heating is used, we recommend to make regular breaks in your journey when driving long distances, so that the body can recuperate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.

CAUTION

■

Do not kneel on the seats or otherwise apply pressure at specific points to

avoid damaging the heating elements for the seat heaters.

■

Do not turn on the seat heater if seats are not occupied.

■

Do not switch on the seat heating if the seats have objects attached to or placed on them, for example a child seat, a bag, etc. A fault of the heating elements in the seat heating can occur.

■

If additional seat covers or protective covers are attached to the seats, do not turn on the seat heater - there is a risk of damaging the seat covers and seat heating.

■

Do not clean the seats using moisture » page 157.

Note

■

The seat heating should only be switched on when the engine is running. This has a significant effect of saving on the battery capacity.

■

If the on-board voltage drops, the seat heating is switched off automatically, in order to provide sufficient electrical energy for the engine control » page 172, Automatic load deactivation.

Rear seats

Introduction



This chapter contains information on the following subjects: Folding the seat backrest forwards

Folding the seat cushions forwards, removing

Folding the seat backrest forwards

Fig. 40

Unlock the seat backrest

First read and observe the introductory information given on page 56.



The luggage compartment can be increased in size by folding the seat backrests forward. The seat backrests can be folded forward individually on vehicles with divided rear seats.

Folding forward

Before folding the rear seats forwards, adapt the position of the front seats in

›

such a way that they are not damaged by the folded rear seats. Unlock the seat backrest by pressing the securing knob A » Fig. 40 and fold it

›

forwards. Pull the head restraint out of the seat backrest.

›

Fold the seat backrest completely forwards.

›

Folding backwards

Push the head restraint into the slightly lifted seat backrest.

›



Then push the seat backrest back into the upright position until the securing

›

56 57

knob clicks into place - check by pulling on the seat backrest » Make sure that the red pin

›

WARNING

■

The belts and the belt locks must be in their original position after folding

back the seat backrests - they must be ready to use.

■

The seat backrests must be securely latched in position so that no objects from the luggage compartment can slip into the passenger compartment under sudden braking – there is a risk of injury.



■

Ensure that the rear seat backrests are properly engaged. It is only then that the three-point seat belt for the middle seat can reliably fulfil its function.

is hidden.



Using the system

CAUTION

Ensure that the seat belts are not damaged when operating the seat backrests. Under no circumstances must the rear seat belts be jammed by the folded back seat backrests.

Fitting

Press the wire loop in the direction of the arrow » Fig. 41 -  and fit it into the

›

bracket. Fold the seat cushion back into its original position.

›



Note

On vehicles with an installed net partition housing, first fold back the left seat rest followed by the right one.

Folding the seat cushions forwards, removing

Fig. 41 Folding the seat cushions forwards and removing

First read and observe the introductory information given on page 56.



The luggage compartment can be increased in size by folding the seat backrests forward or by removing the rear seats.

Folding forward

Pull up the seat squab in the direction of the arrow 1 » Fig. 41 and fold for-

›

wards in the direction of the arrow

Removing

Fold the seat cushion forward.

›

Press the wire loops in the direction of the arrow » Fig. 41 -  and remove the

›

seat squab from its bracket.

Head restraints



 Introduction

This chapter contains information on the following subjects:

Adjusting the head restraints

Storing the head restraints in the seat squabs 58

Adjusting the head restraints

Fig. 42 Head restraint: adjusting/removing

First read and observe the introductory information given on page 57.



Setting the height

Grasp the side of the head restraint with both hands and push it upwards as re-

›

quired » Fig. 42 - . To move the head restraint downwards, press and hold the safety but-

›

ton » Fig. 42 -  with one hand and push the head restraint down with the other hand.

Removing/installing

Pull the head restraint out of the seat backrest as far as the stop.

›





Seats and storage

Press the locking button in the direction of the arrow » Fig. 42 -  and pull the

›

head restraint out. To re-insert the head restraint, push it far enough down into the seat backrest

›

until the locking button clicks into place.

Best protection is achieved if the top edge of the head restraint is at the same level as the upper part of your head.

The head restraints must be adjusted to match the size of the seat occupant. Correctly adjusted head restraints together with the seat belts offer effective protection for the occupants » page 125.

WARNING

■

The head restraints must be correctly adjusted in order to offer effective

protection for the occupants in the event of an accident.

■

Never drive with the head restraints removed - there is a risk of injury.

■

If the rear seats are occupied, the rear head restraint must not be in the

lower position.

Storing the head restraints in the seat squabs

Fig. 43

Rear seats: Inserting head restraints in the seat cushions

First read and observe the introductory information given on page 57.



The rear head restraints can be inserted into the corresponding holes in the folded seat squabs » Fig. 43.

Boot

 Introduction

This chapter contains information on the following subjects: Class N1 vehicles

Fastening elements 59 Folding hooks 60 Fixing nets 60 Boot cover 61 Further positions of the luggage compartment cover 61 Retractable luggage compartment cover (Fabia Estate) 62

Please observe the following for the purpose of maintaining good handling characteristics of your vehicle:



Distribute loads as evenly as possible.

›

Place heavy objects as far forward as possible.

›

Attach the items of luggage to the lashing eyes or using the fixing

›

net » page 59.

In the event of an accident, even small and light objects gain so much kinetic energy that they can cause severe injuries.

The magnitude of the kinetic energy is dependent on the speed at which the vehicle is travelling and the weight of the object.

Example: In the event of a frontal collision at a speed of 50 km/h, an object weighing 4.5 kg produces energy corresponding to 20 times its own weight. This means that it results in a weight of approx. 90 kg “ ”.

WARNING

■

Store the objects in the boot and attach them to the lashing eyes.

■

Loose objects can be thrown forward during a sudden manoeuvre or in case of an accident and can injure the occupants or other road users.

■

Loose objects could hit a deployed airbag and injure occupants – there is a



risk of death.



Using the system

WARNING (Continued)

■

Please note that the handling properties of the vehicle may be affected when transporting heavy objects as the centre of gravity can be shifted – there is a risk of an accident. The speed and style of driving must be adjusted accordingly.

■

If the items of luggage or objects are attached to the lashing eyes with unsuitable or damaged lashing straps, injuries can occur in the event of braking manoeuvres or accidents. To prevent items of luggage from being thrown forward, always use suitable lashing straps which must be firmly attached to the lashing eyes.

■

Items carried in the luggage compartment must be stowed in such a way that no objects are able to slip forward under sudden driving manoeuvres or braking – there is a risk of injury.

■

When transporting fastened objects which are sharp and dangerous in the boot that has been enlarged by folding the rear seats forward, ensure the safety of the passengers transported on the other rear seats » page 126, Cor- rect seated position of the rear seat passengers.

■

If the rear seat next to the folded forward seat is occupied, ensure maximum safety, e.g. by placing the goods to be transported in such a way that the seat is prevented from folding back in case of a rear collision.

■

Never drive with the tailgate fully opened or slightly ajar otherwise exhaust gases may get into the interior of the vehicle – risk of poisoning.

■

Under no circumstances, should the permissible axle loads and permissible gross weight of the vehicle be exceeded – there is the risk of an accident.

■

Never transport people in the boot!

CAUTION

Please ensure that the heating elements for the rear window heater are not damaged as a result of abrasive objects.

Note

Tyre pressure must be adjusted to the load

» page 174, Tyre service life.

Class N1 vehicles

First read and observe the introductory information and safety warnings on page 58.



On class N1 vehicles, which are not fitted with a protective grille, a lashing set which complies with the standard EN 12195 (1 - 4) must be used for fastening the load.

The proper functioning of the electrical system is essential for the safe operation of the vehicle. It is important to ensure that it is not damaged during modifications or when loading or unloading the luggage compartment.

Fastening elements

Boot: Lashing eyes and fastening elements

Fig. 44

First read and observe the introductory information and safety warnings on page 58.



The following fastening elements are found in the luggage compartment » Fig. 44.



Lashing eyes for fastening items of luggage and fixing nets.

Fastening elements for fastening fixing nets.



CAUTION

The maximum permissible load of the lashing eyes is 3.5 kN (350 kg).

Seats and storage



Note

The upper front lashing eyes are located underneath the folding rear seat backrest » Fig. 44.

Folding hooks

Fig. 45

Boot: folding hooks

First read and observe the introductory information and safety warnings



Folding hooks for attaching small items of luggage, such as bags etc., are provided on both sides of the luggage compartment. » Fig. 45.

on page 58.

CAUTION

The maximum permissible load of the hook is 7.5 kg.

Fixing nets



Fig. 46 Fixing net: double horizontal pocket, floor fixing net/double vertical pockets

First read and observe the introductory information and safety warnings on page 58.



Fixing examples for a fixing net as a horizontal pocket, floor fixing net » Fig. 46 -



and a horizontal pocket » Fig. 46 - .

WARNING

Do not exceed the maximum permissible load of the fixing nets. Heavy objects are not secured adequately – there is a risk of injury.



CAUTION

■

The maximum permissible load of the fixing nets is 1.5 kg.

■

Do not place any sharp objects in the nets – risk of damaging the net.



Using the system

Boot cover

Fig. 47 Removing the boot cover

First read and observe the introductory information and safety warnings



The boot cover can be removed if you wish to transport bulky goods.

Removing cover

Unhook support straps 1 » Fig. 47.

›

Remove the cover from the holders 2 by lightly knocking on the underside of

›

the cover in the area between the holders.

Installing the cover

Place the cover on the contact surfaces of the side trim panel.

›

Place the recesses of the cover 3 » Fig. 47 over the holders 2 in the side trim

›

panel. Interlock the cover by lightly knocking on the top side of the cover in the area

›

between the holders. Hook the support straps 1 on the boot lid.

›

on page 58.

WARNING

No objects should be placed on the boot cover, the vehicle occupants could be endangered if there is sudden braking or the vehicle collides with something.

CAUTION

■

When closing the boot lid, jamming and damage to the luggage compartment cover or the side trim panel can occur if handled in an unprofessional way. The following guidelines must be observed.

■

The recesses in the cover 3 » Fig. 47 must lock in the holders in the side trim

panel 2.

■

The items which are transported must not exceed the height of the luggage

compartment cover.

■

The cover must not be jammed in the seal of the boot lid when it is in the

opened position.

■

There must be no object in the gap between the opened cover and the rear

backrest.

Note

Opening the boot lid also lifts up the boot cover.

Further positions of the luggage compartment cover

Fig. 48

The luggage compartment cover: Stowed in the lower position/be-

hind the rear seats

First read and observe the introductory information and safety warnings on page 58.



The luggage compartment cover can be fitted to the following positions:

In the lower position on the support elements » Fig. 48 -  »

›

Behind the rear seats » Fig. 48 - .

›





Seats and storage

CAUTION

In this position » Fig. 48 -  the luggage compartment cover is designed for small objects up to a weight of 2.5 kg.

Retractable luggage compartment cover (Fabia Estate)

Variable loading floor in the luggage compartment (Fabia Estate)



Introduction



This chapter contains information on the following subjects: Dividing up the luggage compartment with variable loading floor 62

Removing and refitting the variable loading floor 63 Removing and installing carrier rails 63

The variable loading floor makes handling of bulky items of luggage easier.

CAUTION

The maximum permissible load of the variable loading floor is 75 kg.

Boot: foldable boot cover/removing foldable boot cover

Fig. 49

First read and observe the introductory information and safety warnings on page 58.



Pulling out

Pull the retractable luggage compartment cover in direction of arrow

›

» Fig. 49 as far as the stop into the secured position.

Retracting

Press the cover in the handle area in the direction of the arrow 2, and the cov-

›

er automatically rolls up into position.

Removing

The fully folded luggage compartment cover can be removed to transport bulky

›

goods by pressing on the side of the cross rod in the direction of the arrow and taking it out by moving it in the direction of the arrow 4.

WARNING

No objects should be placed on the foldable boot cover.

Using the system

Note

The room under the variable loading floor can be used to stow objects.



Dividing up the luggage compartment with variable loading floor

Fig. 50

Dividing the boot with variable loading floor

First read and observe the introductory information and safety warn-



ings on page 62.



Lift up the part with the grip and secure it by sliding it into the grooves marked

›

with the arrows » Fig. 50.



Removing and refitting the variable loading floor

Removing and installing carrier rails

Fig. 51 Fold up variable loading floor/remove

First read and observe the introductory information and safety warnings



Removing

Unlock the variable loading floor by turning the securing bolts A around 180°

›

anticlockwise » Fig. 51. Fold up the loading floor by moving it in the direction of the arrow B.

›

Fold up the variable loading floor in the direction of the arrow 1 » Fig. 51 and

›

remove by pulling in the direction of the arrow

Fitting

Fold up the variable loading floor and place it on the carrier rails.

›

Fold out the variable loading floor.

›

Lock the variable loading floor by turning the locking bolt A to the right by ap-

›

prox. 180°.

on page 62.

WARNING

Ensure that the carrier rails and variable loading floor are correctly fastened when fitting the variable loading floor. If this is not the case, there is a risk of injury for the occupants.

Fig. 52 Slacken check points/remove carrier rails

First read and observe the introductory information and safety warnings



Removing

Undo the securing points B » Fig. 52 on the carrier rails using the vehicle key or

›

a flat screwdriver.

Grasp the carrier rail A at position 1 and slacken it by pulling in the direction

›

of arrow. You can take out the removable storage compartments in order to fa-

cilitate the removal » page 75, Storage compartments in the boot.

Grasp the carrier rail A at position 2 and slacken it by pulling in the direction

›

of arrow.

The carrier rail on the other side of the luggage compartment can be removed in

›

the same way.

Fitting

Position the carrier rails on the sides of the boot.

›

Press the two securing points

›

Check the attachment of the carrier rails by pulling it.

›



WARNING

Ensure that the carrier rails and variable loading floor are correctly fastened

when fitting the variable loading floor. If this is not the case, there is a risk of

injury for the occupants.

on page 62.

» Fig. 52 on each carrier rail to the stop.

Seats and storage



Net partition (Fabia Estate)

 Introduction

This chapter contains information on the following subjects: Using the net partition behind the rear seats

Using the net partition behind the front seats 65 Removing and refitting the net partition housing 65

WARNING

■

The belt locks and the belts must be in their original position after folding

back the seat cushions and backrests - they must be ready to use.

■

The seat backrests must be securely latched in position so that no objects from the luggage compartment can slip into the passenger compartment under sudden braking – there is a risk of injury.

■

Ensure that the rear seat backrests are properly engaged. It is only then that the three-point seat belt for the middle seat can reliably fulfil its function.

■

Make sure that the transverse rod is inserted into the mounts C » Fig. 53 on page 64 or » Fig. 54 on page 65 in the forward position.

Using the net partition behind the rear seats

First read and observe the introductory information and safety warnings on page 64.



Extending

Open the rear right door.

›

Fold down the rear seat backrests slightly forwards, which makes it possible to

›

clear the access for removing the net partition. Pull the net partition by tab A » Fig. 53 out of the housing B in the direction of

›

mounts C. Insert the transverse rod into one of the mounts C and push forwards.

›

Insert the transverse rod into the mount C on the other side of the vehicle in

›

the same way. Then push the seat backrest back into the upright position until the securing

›

knob clicks into place - check by pulling on the seat backrest.

Retracting

Pull the transverse rod back slightly first on one side and then on the other and

›

remove it from the mounts

Hold the transverse rod in such a way that the net partition can slowly roll up

›

into the housing B without being damaged.

If you wish to use the entire boot, the foldable boot cover can be re-



moved » page 62.

» Fig. 53.



Fig. 53

Using the system

Extending/retracting the net partition

Using the net partition behind the front seats

Removing and refitting the net partition housing

Fig. 55

Rear seats: Net partition housing

Fig. 54 Extending/retracting the net partition

First read and observe the introductory information and safety warnings



Extending

Open the rear right door.

›

Fold the seat cushions and rear seat rests forward.

›

Pull the net partition by tab A » Fig. 54 out of the housing B in the direction of

›

mounts Insert the transverse rod into one of the mounts C and push forwards.

›

Insert the transverse rod into the mount C on the other side of the vehicle in

›

the same way.

Retracting

Pull the transverse rod back slightly first on one side and then on the other and

›

remove it from the mounts

Hold the transverse rod in such a way that the net partition can slowly roll up

›

into the housing B without being damaged. Fold the rear seats back into their original position.

›

on page 64.

» Fig. 54.

First read and observe the introductory information and safety warnings on page 64.



Removing

Open the rear right door.

›

Fold the seat cushions and rear seat backrests forward – first the left and then

›

the right backrest. Push the net partition housing A » Fig. 55 in the direction of the arrow 1 and

›

remove it from the mount on the right seat back in the direction of the arrow

Fitting

Insert the recesses on the net partition housing into the mounts on the rear

›

seat backrests. Push the net partition housing in the opposite direction of the arrow 1 as far

›

as the stop. Fold the rear seats back into their original position.

›



Bicycle carrier in the luggage compartment



Introduction

This chapter contains information on the following subjects: Install cross member 66

Install bicycle carrier Put bicycle into the bicycle carrier Secure the stability of the bicycles with a belt 67

Seats and storage





WARNING

When transporting bicycles, ensuring the safety of the passengers is paramount.

CAUTION

Take care handling the bicycle - there is a risk of damaging the vehicle.

Install cross member

Install bicycle carrier

Fig. 57

Install bicycle carrier



Fig. 56

Install cross member

First read and observe the introductory information and safety warnings



Remove the rollable luggage compartment cover » page 62; if necessary we

›

recommend you remove the net partition » page 65. Remove the head rests from the rear seat rests and fold the rear seats for-

›

ward » page 56. Undo the securing screws C » Fig. 56 and remove a little to unlock the retain-

›

ers Place the cross member A with the fixed part onto the left lashing eye and

›

then place it on the right lashing eye with the removable part of the cross member Press the holders B until they latch. Tighten the securing screws C.

›

Check how well the cross member is fastened by pulling on it.

›

on page 65.

Using the system

First read and observe the introductory information and safety warnings on page 65.



Position the approved bicycle carrier on the cross member.

›

Remove bolt A » Fig. 57 a little and push the frame side rail (aluminium part)

›

towards the cross member until the socket latches. Insert the screw A into the nut.

›

Undo the screw B on the movable part of the bicycle carrier and unscrew.

›

Place the movable part of the fixture, depending on the size of the vehicle, in

›

one of the possible positions so that the bicycle does not touch the boot lid. We recommend to place the moveable part of the fixture in such a position that 7 holes are visible between the screw A and the moveable part. Insert the screw B into the desired position and tighten.

›



Put bicycle into the bicycle carrier

Secure the stability of the bicycles with a belt

Fig. 58 Put in the bicycle/example fastening the front wheel

First read and observe the introductory information and safety warnings



Remove the front wheel of the bicycle before installing it.

›

Slacken the quick tension jack on the fixing axle of the bicycle carrier and adjust

›

according to the width of the bicycle fork. Place the bicycle fork on the fixing axle and tighten with the quick release lev-

›

er » Fig. 58 - . Position the left pedal of the bicycle forward, in order to attach the front wheel

›

more easily. Undo bolt A » Fig. 57 on page 66 and push the bicycle carrier to the left to-

›

gether with the mounted bicycle to prevent a collision between the handlebars and the side window of the luggage compartment. Carefully guide the boot lid downwards without letting go of it. Check whether

›

there is sufficient room between the steering bars and the rear window. If necessary, adjust the position of the movable part of the bicycle carrier to prevent a collision » page 66. It is best to store the removed front wheel between the left crank and the bicy-

›

cle frame, attach it with a strap to the front fork » Fig. 58 -  or to one of the fixing points. The second carrier is installed and the bicycle is secured in a similar way.

›

on page 65.

Fig. 59 Securing bicycles

First read and observe the introductory information and safety warnings



To slacken the rubber part of the clamp, push both parts against each other and

›

open the clamp. Position the clamp with the rubber part to the front (in direction of travel) as

›

low down on the seat post as possible and lock it » Fig. 59 - . When transporting two bicycles, stretch the belt » Fig. 59 -  between the sad-

›

dles by moving the bicycles apart. Hook the carabiners on the ends of the belt into the lashing eyes behind the

›

rear seats » Fig. 59 - . Pull the belt through the tensioning clasps on both sides in turn.

›

If necessary, you can correct the position of the bicycles in the vehicle.

›

on page 65.

Roof rack system



Introduction

This chapter contains information on the following subjects:



Attachment points 68 Roof load 68

Seats and storage





WARNING

■

The items being transported on the roof rack must be reliably attached – there is the risk of an accident.

■

Always secure the load with appropriate and undamaged lashing straps or tensioning straps.

■

Distribute the load evenly over the roof rack system.

■

The handling properties of your vehicle change when you transport heavy or bulky items on the roof rack system as a result of the centre of gravity being shifted and the greater area exposed to the wind – there is the risk of an accident. The style of driving and speed must therefore be adapted to the current circumstances.

■

Avoid abrupt and sudden driving/braking manoeuvres.

■

Adjust the speed and driving style to the visibility, weather, road and traffic conditions.

■

The permissible roof load, permissible axle loads and gross permissible weight of the vehicle must not be exceeded under any circumstances – there is the risk of an accident.

CAUTION

■

Only use roof rack systems approved by ŠKODA AUTO a.s.

■

The fitting instructions supplied with the roof luggage rack system must be ob-

served when handling roof racks.

■

On models fitted with a power sliding/tilting roof, ensure that the opened slid-

ing/tilting roof does not strike any items of luggage transported on the roof.

■

Ensure that the boot lid does not hit the roof load when opened.

■

The height of the vehicle changes after mounting a roof luggage rack system

and the load that is secured to it. Compare the vehicle height with available clearances, such as underpasses and garage doors.

■

Always remove the roof luggage rack system before entering an automated car

wash.

■

Ensure the roof aerial is not impaired by the secured load.

For the sake of the environment

The increased aerodynamic drag results in a higher fuel consumption.

Attachment points

Fig. 60

Attachment points for roof bars

First read and observe the introductory information and safety warnings on page 67.



Perform the assembly and disassembly according to the enclosed instructions.

CAUTION

Observe the information regarding the assembly and disassembly in the enclosed instructions.

Roof load

First read and observe the introductory information and safety warnings on page 67.



The maximum permissible roof load (including roof rack system) of 75 kg and the maximum permissible total weight of the vehicle should not be exceeded.

The full permissible roof load cannot be used if a roof rack system with a lower load carrying capacity is used. In this case, the roof rack system must only be loaded up to the maximum weight limit specified in the fitting instructions.



Note

If the vehicle is not factory-equipped with a roof rack, it can be purchased from the ŠKODA Original Accessories.

Using the system



Useful equipment

 Introduction

This chapter contains information on the following subjects:

Cupholders

Ashtray 69

Cigarette lighter 70

12-volt power outlet 70

Clothes hook 71

Car park ticket holder 71

WARNING

■

Do not place anything on the dash panel. These objects might slide or fall down while you are driving (under acceleration or when cornering) and could distract you from the traffic - there is a risk of an accident.

■

Make sure that no objects from the centre console or from other storage compartments can get into the driver's footwell while you are driving. You would then no longer be able to apply the brakes or operate the clutch or accelerator pedal – there is a risk of an accident.

■

Ash and cigarette or cigar stubs must only be discarded in ashtrays.

Cupholders

First read and observe the introductory information and safety warnings on page 69.



Two beverage containers can be placed into the recesses A » Fig. 61. One beverage container can be placed into the recess B.

WARNING

■

Never put hot cups in the cup holder. They may spill as the vehicle moves –

there is a risk of scalding.

■

No objects should be placed in the holders that might endanger the vehi-

cle's occupants if the vehicle brakes suddenly or the vehicle is in collision.

■

Do not use any cups or beakers which are made of brittle material (e.g. glass,

porcelain). This could lead to injuries in the event of an accident.

CAUTION

Do not leave open beverage containers in the cup holder during the journey. There is a risk of spilling e.g. when braking which may cause damage to the electrical components or seat upholstery.

Ashtray



Fig. 61

Cup holder

Centre console: Ashtray at the front/rear

Fig. 62

First read and observe the introductory information and safety warnings on page 69.



The ashtray can be used for discarding ash, cigarettes, cigars and the like » .

Seats and storage



Removing

Pull the ashtray » Fig. 62 out and up.

›

Fitting

Insert the ashtray vertically.

›

WARNING

Never put flammable objects in the ashtray – there is a risk of fire.

CAUTION

Do not hold the ashtray by the cover when removing it – there is a risk of it breaking.

WARNING

■

Take care when using the cigarette lighter! Improper use of the cigarette

lighter can cause burns.

■

The cigarette lighter also operates when the ignition is switched off or the ignition key withdrawn. Therefore never leave children unattended in the vehicle.

Note

■

The cigarette lighter socket can also be used as a 12Volt socket for electrical ap-

pliances » page 70.

■

Further information » page 147, Services, modifications and technical altera-



tions.



Cigarette lighter

Fig. 63

Centre console: Cigarette lighter

First read and observe the introductory information and safety warnings on page 69.



Operating the cigarette lighter

Press in the button in the cigarette lighter » Fig. 63.

›

Wait until the button pops forward.

›

Remove the cigarette lighter immediately and use.

›

Place the cigarette lighter back into the socket.

›

Using the system

12-volt power outlet

Fig. 64

Boot: Power socket

First read and observe the introductory information and safety warnings on page 69.



Overview of the 12-volt power socket

In the front centre console » Fig. 63 on page 70. In the luggage compartment » Fig. 64.

Using the power socket

Remove the cover from power socket or cigarette lighter, or open the cover for

›

the power socket. Connect the plug for the electrical appliance to the socket.

›

Further information » page 147, Services, modifications and technical alterations.



WARNING

■

Improper use of the 12-volt power socket and the electrical accessories can

cause fires, burns and other serious injuries.

■

Never leave children unattended in the vehicle. The 12-volt power socket and any connected appliances can also be operated when the ignition is switched off or the ignition key is withdrawn.

■

If the connected electric device becomes too hot, switch it off and disconnect it from the power supply immediately.

CAUTION

■

The 12-volt power socket can only be used for connecting approved electrical

accessories with a total power uptake of up to 120 watt.

■

Never exceed the maximum power consumption, otherwise the vehicle's elec-

trical system can be damaged.

■

Connecting electrical components when the engine is not running will drain the

battery of the vehicle – there is a risk of the battery discharging.

■

Only use matching plugs to avoid damaging the 12-volt power socket.

■

Only use accessories that have been tested for electromagnetic compatibility in

accordance with the applicable directives.

■

Before turning the ignition on or off, and before starting the car, switch off the

device connected to the 12-volt power socket to prevent any damage caused by voltage fluctuations.

■

Observe the operating instructions for the connected devices!

WARNING

■

Ensure that any clothes hanging from the hooks do not impair your vision to

the rear.

■

Only use the hooks for hanging light items of clothing and ensure that there

are no heavy or sharp-edged objects in the pockets.

■

Do not use clothes hangers for hanging up items of clothing otherwise this

may reduce the effectiveness of head airbags.

CAUTION

The maximum permissible load of the hooks is 2 kg.

Car park ticket holder

Fig. 65

Windscreen: Parking ticket holder



Clothes hook

First read and observe the introductory information and safety warnings on page 69.



The clothes hooks are located on the handle of the headliner above each of the rear doors.

First read and observe the introductory information and safety warnings on page 69.



The note holder is designed e.g. for attaching car park tickets.

WARNING

The attached note has to always be removed before starting off in order not to restrict the driver's vision.

Seats and storage



Storage compartments

Storage compartments on the front passenger side

 Introduction

This chapter contains information on the following subjects: Storage compartments on the front passenger side

Cooling the storage compartment on the front passenger side 73 Storage compartment on the driver's side 73 Map pockets in the front seats 73 Glasses storage box 74 Stowage compartment in centre console 74 Stowage compartment underneath the front passenger seat 74 Front armrest with storage compartment 75 Storage compartments in the doors 75 Storage compartments in the boot Flexible storage compartment

WARNING

■

First read and observe the introductory information and safety warnings on page 72.



Open/close

75 76

Pull the cover handle in the direction of the arrow » Fig. 66 and fold down the

›

cover. Lift the lid upwards until it clicks into place.

›

A pin holder is located inside the lower flap.

WARNING

The storage compartments must always be closed when driving for safety reasons.



Fig. 66

Dash panel: Storage compartments on the front passenger side



Using the system

Cooling the storage compartment on the front passenger side

Fig. 67

Storage compartment: Using cooling system

First read and observe the introductory information and safety warnings on page 72.



Use the rotary switch » Fig. 67 to open and close the air supply.

›

Opening the air supply when the air conditioning system is switched on allows

cooled air to flow into the storage compartment.

Opening the air inlet when the air conditioning system is on causes fresh or inte-

rior air to flow into the storage compartment.

We recommend closing the air supply if it is operated in heating mode or the cool-

ing system for the storage compartment is not being used.

Storage compartment on the driver's side

First read and observe the introductory information and safety warnings on page 72.



The open stowage compartment below the light switch » Fig. 68.

Map pockets in the front seats

Fig. 69

Front seat rests: Map pockets

First read and observe the introductory information and safety warnings on page 72.



Map pockets are located on the rear of the seat backrests » Fig. 69. The map pockets are intended for storage of maps, magazines, etc.



WARNING

Never put heavy items in the map pockets – risk of injury.



Fig. 68

Dash panel: Storage compartment on the driver's side

CAUTION

Do not put any large items such as bottles or sharp objects into the map pockets, as the pockets and the seat covers could be damaged.

Seats and storage



Glasses storage box

Stowage compartment in centre console

Fig. 70

Detail of the headliner: Glasses storage box

First read and observe the introductory information and safety warnings on page 72.



Press on the bar in the cover of the glasses storage. The compartment folds

›

down » Fig. 70.

WARNING

The compartment must only be opened when removing or inserting the spectacles and otherwise must be kept closed.

CAUTION

■

Do not put any heat-sensitive objects in the glasses storage box - they may be

damaged.

■

The maximum permissible load of the glasses compartment is 250 g.

Fig. 71

Centre console: Stowage compartment

First read and observe the introductory information and safety warnings on page 72.



The open stowage compartment in the centre console » Fig. 71.

Stowage compartment underneath the front passenger seat

Fig. 72

Front seat: Stowage compartment



First read and observe the introductory information and safety warnings on page 72.



Pull the handle to open the lid » Fig. 72.

›

When closing the lid, hold the handle until the compartment is closed.

›

WARNING

The storage compartment must always be closed when driving for safety reasons.





Using the system

CAUTION

The storage compartment is designed for storing small objects of up to 1 kg. in

weight.

Front armrest with storage compartment

Armrest: Storage compartment/open storage compartment

Fig. 73

First read and observe the introductory information and safety warnings on page 72.



Fold the armrest forwards

Press the lower button on the end of the armrest » Fig. 73 - .

›

Fold the arm rest forward and release the button again.

›

Opening the storage compartment

Press the upper button and open the cover of the stowage compartment up-

›

wards » Fig. 73 - .

Note

The moving space of the arms can be restricted if the armrest is folded forwards.

In city traffic the armrest should not be folded forwards.

Storage compartments in the doors



Fig. 74 Storage compartment: in the front door/in the rear door

First read and observe the introductory information and safety warnings



There is a bottle holder at B » Fig. 74 of the pocket in the front doors.

on page 72.

WARNING

Use the section A » Fig. 74 of the door pocket only for storing objects which do not project so that the effectiveness of the side airbag is not impaired.

Storage compartments in the boot

Fig. 75

Boot: Storage compartments



First read and observe the introductory information and safety warnings on page 72.



The cover for the side compartment can be removed, thus enlarging the boot.

Seats and storage



Grasp the top part of the cover and carefully remove it in the direction of the

›

arrow » Fig. 75.

CAUTION

The storage compartments are designed for storing small objects of up to 2.5 kg. in weight in total.

Flexible storage compartment

Fig. 76

Flexible storage compartment

First read and observe the introductory information and safety warnings on page 72.



The flexible storage compartment » Fig. 76 can be fitted to the right-hand side of the luggage compartment.

Fitting

Insert both ends of the flexible storage compartment into the openings of the

›

right side trim panel of the boot and push it downwards until it locks.

Removing

Grasp the flexible storage compartment on the two upper corners.

›

Press the upper corners inwards and release the storage compartment by pull-

›

ing upwards. Remove by pulling towards you.

›

CAUTION

The storage compartment is designed for storing small objects with a maximum total weight of 8 kg.

Note

If the variable loading floor » page 62 is installed in the luggage compartment, no flexible storage compartment can be installed.



Using the system

Heating and air conditioning

Heating, ventilation, cooling

Introduction



This chapter contains information on the following subjects:

Air outlets

Using the air conditioning system economically 78

Operational problems 78

The heating effect is dependent upon the coolant temperature, thus full heat

output only occurs when the engine has reached its operating temperature.

If the cooling system is switched on, the temperature and air humidity drops in

the vehicle. The cooling system prevents the windows from misting up when out-

side temperatures are particularly low.

It is possible to briefly activate recirculated air mode to enhance the cooling ef-

fect.

Please refer to the information regarding recirculated air mode for the air-condi-

tioning system » page 82 or for Climatronic » page 84.

WARNING

For your own safety and that of other road users, ensure that all the windows are free of ice, snow and misting. Please familiarize yourself about how to correctly operate the heating and ventilation systems, how to demist and defrost the windows, as well as with the cooling mode.

CAUTION

■

The air inlet in front of the windscreen must be free (e.g. of ice, snow or leaves)

to ensure that the heating and cooling system operates properly.

■

After switching on the cooling Condensation from the evaporator of the air con-

ditioning may drip down and form a puddle below the vehicle. This is not a leak.

Note

■

The exhaust air streams out through vents at the rear of the luggage compart-

ment.

■

We recommend that you do not smoke in the vehicle when the recirculating air mode is operating since the smoke which is drawn at the evaporator from the interior of the vehicle forms deposits in the evaporator of the air conditioning system. This produces a permanent odour when the air conditioning system is operating which can only be eliminated through considerable effort and expense (replacement of compressor).

Air outlets

Fig. 77 Air outlet vents

First read and observe the introductory information and safety warnings on page 77.



Warmed, not warmed fresh or cooled air will flow out of the opened air outlet vents according to the setting of the control and the outside atmospheric conditions.

The direction of airflow can be adjusted using the air outlet vents 3 and 4 » Fig. 77 and the outlets can also be opened and closed individually.

Open the air outlet vents 3 and 4

Turn the vertical wheel (air vents 3) » Fig. 77 or the horizontal wheel (air outlet

›

nozzles 4) to the  position.





Heating and air conditioning

Close air outlet vents 3 and 4

Turn the vertical wheel (air vents 3) » Fig. 77 or the horizontal wheel (air outlet

›

nozzles 4) to the 0 position.

Change air flow of air outlet vents 3 and 4

In order to change the strength of the air flow, swivel the horizontal lamellas

›

with the aid of the moveable adjuster » Fig. 77. In order to change the lateral direction of the air flow, swivel the vertical lamel-

›

las with the aid of the moveable adjuster.

Set the air supply to the individual vents with the air distribution control

» Fig. 78 on page 79.

Note

Do not cover the air outlet vents with objects of any kind.

Operational problems

First read and observe the introductory information and safety warnings on page 77.



If the cooling system does not operate at outside temperatures higher than +5 °C, there is a problem in the system. The reasons for this may be.

One of the fuses has blown. Check the fuse and replace if necessa-

›

ry » page 192. The cooling system has switched off automatically for a short time because the

›

coolant temperature of the engine is too hot » page 11.

If you are not able to resolve the fault yourself, or if the cooling output has reduced, switch off the cooling system and obtain assistance from a specialist garage.



Using the air conditioning system economically

First read and observe the introductory information and safety warn-

on page 77.

ings



The air conditioning system compressor uses power from the engine when in cooling mode, which will affect the fuel consumption.

It recommended to open the windows or the doors of a vehicle for which the interior has been strongly heated through the effect of direct sunlight in order to allow the heated air to escape.

The cooling system should not be switched on if the windows are open.

For the sake of the environment

Pollutant emissions are also lower when fuel is being saved » page 104.

Using the system

Heating



Introduction

This chapter contains information on the following subjects: Operation

Setting Recirculated air mode 80



79 79



Operation

Fig. 78 Heating: Control elements

Setting

First read and observe the introductory information given on page 78.



Recommended basic settings of the heating controls.

Setting

Defrosting the windshield and side windows

Free windshield and side windows from mist

The fastest heating

Comfortable heating Desired temperature 2 or 3

To the right up to the

Desired temperature 2 or 3

Control dial position » Fig. 78 on page 79

A B C

stop

To the stop to the

right

First read and observe the introductory information given on page 78.



Functions of the individual controls » Fig. 78.

Set the temperature (turn to the left to reduce the temperature: turn to the right to increase temperature)

Set the blower level (level 0: blower off, level 4: the highest blower speed)

Set the direction of the air outlet » page 77 Recirculating air operation on/off » page 80



Controls A and C » Fig. 78 can be set to any intermediate position.

WARNING

The blower should always be on to prevent the windows from misting up.

Button  » Fig. 78 on

page 79



  



  

Do not switch on

Briefly switch on Opening

Do not switch on Opening

Air outlet vents 4 » Fig. 77 on

page 77

Open and align with the side win-

dow

Open and align with the side win-

dow



Fresh air mode - ventilation To the stop to the left Desired position



Do not switch on Opening

Heating and air conditioning



We recommend that you leave the air outlet vents 3 » Fig. 77 on page 77 in the open position in all operating modes.

Note

If the air distribution is directed only towards the windows, the total amount of air is used to defrost the windows and thus no air will be fed to the footwell. This can limit the heating comfort.

Recirculated air mode

First read and observe the introductory information given on page 78.



Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the  button.

›

The indicator light in the button lights up.

Press the  button again.

›

The indicator light in the button goes out.

Recirculated air mode is switched off automatically if the air distribution control

» Fig. 78 on page 79 is turned to the  position. Recirculated air mode can be

switched on again from this setting by pressing the  button again.

WARNING

Never leave recirculated air mode on over a longer period, as “stale air” can cause fatigue in the driver and the passengers, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases. Switch off recirculated air mode as soon as the windows start to mist up.

Air conditioning system (manual air conditioning system)

Introduction



This chapter contains information on the following subjects:



Operation 81 Setting the air conditioning system 82 Recirculated air mode 82

The cooling system operates only if the following conditions are met.

The cooling system is switched on » page 81.



The engine is running.



The outside temperature is above approximately +2 °C.

 

The blower switch is switched on (positions 1-4).

If the desired interior temperature can also be achieved without activating the cooling system, fresh air mode should be selected.

If the coolant temperature is too high, the cooling system is switched off to ensure that the engine cools down.

CAUTION

■

Under certain circumstances, air at a temperature of about 5 °C can flow out of

the vents when the cooling system is switched on.

■

Lengthy and uneven distribution of the air flow out of the vents (especially around the feet) and large differences in temperature, for example, when getting out of the vehicle, can cause susceptible individuals to catch a cold.

Note

We recommend that you have the air conditioning system cleaned by a specialist



garage once every year.



Using the system

Operation

Fig. 79 The air conditioning system: Control elements

First read and observe the introductory information and safety warnings on page 80.



Functions of the individual controls » Fig. 79.

Set the temperature (turn to the left to reduce the temperature: turn to the right to increase temperature)

Set the blower level (level 0: blower off, level 4: the highest blower speed)

Set the direction of the air outlet » page 77 Recirculating air operation on/off » page 82





Switch cooling system on/off

Note

The warning light in the  button lights after activation, even if not all of the conditions for the function of the cooling system are met » page 80. The operational readiness of the cooling system is indicated by the indicator light in the button lighting up.



Heating and air conditioning

Setting the air conditioning system

First read and observe the introductory information and safety warnings on page 80.



Recommended basic settings of the air conditioning controls.

Setting

Defrost/defog windscreen and side windows

The fastest heating

Comfortable heating

The fastest cooling

Optimal cooling

Fresh air mode - ventilation

We recommend that you do not use this setting in countries with high humidity levels. This can result in heavy cooling of the window glass and the following fogging from outside.

Under certain conditions, recirculated air mode » page 82 may come on automatically; the warning light will then light up in the  button.

We recommend that you leave the air outlet vents 3 » Fig. 77 on page 77 in the open position in all operating modes.

Recirculated air mode

First read and observe the introductory information and safety warnings on page 80.



Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on/off

Press the  button.

›

Control dial position » Fig. 79 on page 81 Button » Fig. 79 on page 81

A B C

Desired tempera-

ture

To the stop to the

right

Desired tempera-

ture

To the left up to

the stop

Desired tempera-

ture

To the stop to the

left

3 or 4

2 or 3

briefly 4, then

2 or 3

1, 2 or 3

Desired position





  

  



The indicator light in the button lights up.

Press the  button again.

›

The indicator light in the button goes out.

Recirculated air mode is switched off automatically if the air distribution control

» Fig. 79 on page 81 is turned to the  position.

Recirculated air mode can be switched on again from this setting by pressing the

 button again.

 

Do not switch on

Briefly switch on Switched off Opening

Do not switch on Switched off Opening

Briefly switch on

Do not switch on Activated Open and align to the roof

Do not switch on Switched off Opening

Automatically switchedonOpen and align with the side

Activated Opening

Air outlet vents 4 » Fig. 77

on page 77

window



Using the system

WARNING

Climatronic (automatic air conditioning system)

 Introduction

This chapter contains information on the following subjects: Control elements

Automatic mode Setting the temperature Recirculated air mode 84 Controlling the blower Defrosting windscreen 85

Climatronic in automatic mode ensures the best-possible setting of the temperature of the outflowing air, the blower stage and air distribution.

The system also takes sunlight into account, which eliminates the need to alter the settings manually.

The cooling system operates only if the following conditions are met.

The cooling system is switched on » page 83.



The engine is running.



The outside temperature is above approximately +2 °C.



If the coolant temperature is too high, the cooling system is switched off to ensure that the engine cools down.

Note

We recommend that you have Climatronic cleaned by a specialist garage once every year.

83 84 84

Control elements



Fig. 80 Climatronic: Control elements

First read and observe the introductory information given on page 83.



The buttons/control dial

Setting the interior temperature » page 84

Display

Display of selected interior temperature

Degrees Celsius or Fahrenheit, change the displayed temperature units » page 84

Automatic operation of the air conditioning system

Ventilation or defrosting of the windscreen activated

Direction of air flow

Recirculated air mode activated

Cooling system activated

Blower speed set

The buttons/control dial



Adjust the blower speed » page 85

Interior temperature sensor

Automatic mode » page 84



De-mist or de-ice the windscreen » page 85





Heating and air conditioning

Air flow to the windows



Air flow to the upper body



Air flow in the footwell



Recirculating air operation on/off » page 84



Switch cooling system on/off



Note

Do not stick anything on or cover the interior temperature sensor 11 » Fig. 80; it could have an unfavourable effect on the Climatronic system.

Automatic mode

First read and observe the introductory information given on page 83.



The automatic mode is used in order to maintain a constant temperature and to demist the windows in the interior of the car.

Switching on

Set a temperature between +18 °C and +29 ℃.

›

Move the air outlet vents 3 » Fig. 77 on page 77 and 4 so that the air flow is di-

›

rected slightly upwards. Press the

›

Automatic mode can be switched off by pressing any of the air distribution buttons or by increasing/decreasing the blower speed. The temperature is nevertheless regulated.



button » Fig. 80 on page 83;



will appear in the display.

Setting the temperature

First read and observe the introductory information given on page 83.



Setting temperature

Switch on the ignition.

›

Turn the control dial 1 » Fig. 80 on page 83 to the left or to the right to in-

›

crease or decrease the temperature.

Switching between Celsius and Fahrenheit

Press and hold the

›



and  buttons simultaneously.

The information appears in the display in the desired temperature unit (no.

» Fig. 80 on page 83).

The interior temperature can be set between +18 °C and +29 ℃. The interior temperature is regulated automatically within this range.

If you set the temperature below +18 ℃, “LO” appears in the display. If you set a temperature higher than +29 ℃, “HI” appears in the display. Climatronic operates at maximum cooling or heating capacity respectively at ei-

ther end position. There will be no automatic temperature control.



CAUTION

Recirculated air mode

First read and observe the introductory information given on page 83.



Recirculated air mode prevents polluted air from outside the vehicle getting into the vehicle, for example when driving through a tunnel or when standing in a traffic jam.

Switching on

Press the  button » Fig. 80 on page 83.

›



The display shows the  icon.

Switching off

Press the

›

The  icon in the display goes out.

Never leave recirculated air mode on over a longer period, as “stale air” can

cause fatigue in the driver and the passengers, reduce attention levels and al-

so cause the windows to mist up. The risk of having an accident increases.

Switch off recirculated air mode as soon as the windows start to mist up.



button » Fig. 80 on page 83 again.

WARNING





Using the system

Note

If recirculated air mode is switched on for around 15 minutes, the symbol  will begin to flash in the display as a sign that the recirculated air mode is switched on long-term. If the recirculated air mode is not switched off, the symbol flashes for around 5 minutes.

Controlling the blower

First read and observe the introductory information given on page 83.



The Climatronic system controls the blower stages automatically in line with the interior temperature. However, the blower level can be manually adjusted to suit your particular needs.

Turn control dial 10 » Fig. 80 on page 83 to the left or to the right to increase or

›

decrease the blower speed.

If the blower is switched off, the Climatronic system is switched off. The blower speed set is indicated by displaying the corresponding number of seg-

ments in icon

» Fig. 80 on page 83 in the display.

WARNING

■

“Stale air” may result in fatigue in the driver and occupants, reduce attention levels and also cause the windows to mist up. The risk of having an accident increases.

■

Do not switch off the Climatronic system for longer than necessary.

■

Switch on the Climatronic system as soon as the windows mist up.

Defrosting windscreen

First read and observe the introductory information given on page 83.



Switching on

Press the  button » Fig. 80 on page 83.

›

Switching off

Press the  button » Fig. 80 on page 83 again or press the

›



button.

More air flows out of the air outlet vents 1 and 2 » Fig. 77 on page 77. The temperature control is controlled automatically.



Heating and air conditioning

Communication and multimedia

Universal telephone preinstallation GSM II

Introduction



This chapter contains information on the following subjects: Mobile phones and two-way radio systems

Introductory information 86 Phone Phonebook 87 Operating the phone on the multifunction steering wheel 87 Inserting the mobile phone and adapter 88 Managing telephone calls with the help of the adapter 89 Connecting the mobile phone to the hands-free system Symbols in the MAXI DOT display 90 Telephone operation in the MAXI DOT display

Mobile phones and two-way radio systems

First read and observe the introductory information given on page 86.



ŠKODA permits the operation of mobile phones and two-way radio systems with a professionally installed external aerial and a maximum transmission power of up to 10 watts.

Please consult a ŠKODA Partner for information about the possibility of installing and operating mobile phones and two-way radio systems with a transmission power of more than 10 W.

Operating mobile phones or two-way radio systems may interfere with the functionality of the electronic systems in your vehicle.

The possible reasons for this are.

no external aerial.

›

external aerial incorrectly installed.

›

transmission power greater than 10 watts.

›

WARNING

■

Concentrate fully at all times on your driving! As the driver you are fully responsible for road safety. Use the telephone system only to such an extent that you are in full control of your vehicle at any time.

■

The national regulations for using a mobile phone in a vehicle must be observed.

■

If a mobile phone or a two-way radio system is operated in a vehicle without an external aerial or an external aerial which has been installed incorrectly,

this can increase the strength of the electromagnetic field inside the vehicle.

■

Two-way radio systems, mobile phones or mounts must not be installed on airbag covers or within the immediate deployment range of the airbags.

■

Never leave a mobile phone on a seat, on the dash panel or in another area, from which it can be thrown during a sudden braking manoeuvre, an accident or a collision - risk of injury.

■

The Bluetooth® function must be switched off by a specialist workshop before the vehicle is transported by air.



Note

■

We recommend that mobile phones and two-way radio systems be installed in

the a vehicle by a specialist workshop.

■

Not all mobile phones that enable Bluetooth® communication are compatible

with the universal telephone preinstallation GSM II. You can ask a ŠKODA Partner whether your telephone is compatible with the GSM II universal telephone fitting.

■

The range of the Bluetooth® connection to the hands-free system is restricted

to the vehicle interior. The range is dependent on local factors, e.g. obstacles between the devices and mutual interferences with other devices. If your mobile phone is in a jacket pocket, for example, this can lead to difficulties when establishing a connection with the hands-free-system or transferring data.

Introductory information

First read and observe the introductory information given on page 86.



The universal telephone preinstallation GSM II (hands-free system) includes a convenience mode for the mobile phone via voice control, the multifunction steering wheel, the adapter, radio or the navigation system.





Using the system

The universal telephone preinstallation GSM II comprises the following functions.

Phone Phonebook » page 87.

›

Convenience operation of the telephone via the multifunction steering

›

wheel » page 87. Managing telephone calls via the adapter » page 89.

›

Telephone operation in the MAXI DOT display » page 90.

›

Voice control of the telephone » page 91.

›

Music playback from the telephone or other multimedia units » page 92.

›

All communication between a mobile phone and your vehicle's hands-free system is established with the help of Bluetooth® technology. The adapter serves only for charging the telephone and for transmitting the signal to the vehicle's external aerial.

Note

The following guidelines must be observed » page 86, Mobile phones and twoway radio systems.

Phone Phonebook

First read and observe the introductory information given on page 86.



A phone phonebook is part of the hands-free system. This phone phonebook can be used depending on the type of mobile phone.

Operating the phone on the multifunction steering wheel

Fig. 81

Multifunction steering wheel: Mobile phone operation

After the first connection of the telephone, the system begins to load the phone

book from the phone and the SIM card into the memory of the control unit.

Each time the telephone has established a new connection with the hands-free

system, an update of the relevant phone book is performed. The updating can

take a few minutes. During this time the phone book, which was stored after the

last update was completed, is available. Newly stored telephone numbers are on-

ly shown after the updating has ended.

The update is interrupted if a telephone event (e.g. incoming or outgoing call,

voice control dialogue) occurs during the updating procedure. After the telephone

event has ended, the updating starts anew.

The internal phonebook provides 2 500 free memory locations. Each contact can

contain up to 4 numbers.

If the number of contacts loaded exceeds 2 500, the phone book is not complete.



First read and observe the introductory information given on page 86.



There are buttons in the steering wheel for easy operation of the basic functions

of the phone » Fig. 81 so that the driver is distracted from the traffic as little as

possible when using the phone.

This applies only if your vehicle has been equipped with the universal telephone

preinstallation (hands-free system) at the factory.

If the side lights are switched on, the buttons and the symbols  and  on the

multifunction steering wheel are illuminated.





Communication and multimedia

Button/

wheel

» Fig. 81

2 2 2

Valid for vehicles with the Amundsen+ navigation system.

Valid for vehicles without the Amundsen+ navigation system.

Press button for a long period

Action Operation

Press briefly Accept call, terminate call, entry in the main menu of the telephone, list of selected numbers

of time

Press briefly Switch on/off voice control

Turn upwards Increase the volume

Turn downwards Decrease volume

Reject call, last number dialleda), switch voice control on/off



Inserting the mobile phone and adapter

Fig. 82

Universal telephone preinstallation

First read and observe the introductory information given on page 86.



Only one telephone mount is factory-fitted. An adapter for the mobile phone can be purchased from ŠKODA Original Accessories.

Fitting

First push adapter A in the direction of the arrow » Fig. 82 into the mount as

›

far as the stop. Then press the adapter slightly downwards, until it locks securely into position. Insert the mobile phone into the adapter A (as specified in the instructions

›

from the manufacturer of the adapter).

Removing

Press the side locks on the mount » Fig. 82 at the same time and remove the

›

adapter with the mobile phone.

Using the system

CAUTION

Taking the mobile phone out of the adapter during the call can lead to interruption of the connection. When removing the mobile phone, the connection to the factory-fitted antenna is interrupted, which reduces the quality of the transmitting and receiving signal. The charging of the mobile phone battery is also interrupted.



Managing telephone calls with the help of the adapter

Fig. 83 Principle sketch: Adapter with one button/adapter with two buttons

First read and observe the introductory information given on page 86.



Function overview of the  » Fig. 83 (PTT - “push to talk”) button on the adapter:

Switch on/off voice control;

›

Accept/end a call.

›

Some adapters include the After pressing this button for 2 seconds, the number 112 (Emergency call) is dialled.

SOS

button A » Fig. 83 in addition to the  button.

Connecting the mobile phone to the hands-free system

First read and observe the introductory information given on page 86.



To connect a mobile phone with the hands-free system, the two devices must be paired. Detailed information on this is provided in the operating instructions for your mobile phone.

The following steps must be carried out for the connection.

Activate Bluetooth® and the visibility of your mobile phone on your telephone.

›

Switch on the ignition.

›

Select the Phone - New user menu in the MAXI DOT display and wait until the

›

control unit has completed the search. Select your mobile phone from the menu of the units found.

›

Confirm the PIN1).

›

If the hands-free system announces (as standard SKODA_BT) on the display of

›

the mobile phone, enter the PIN1) within 30 seconds and wait, until the connection is established2). To finish pairing, confirm the creation of the new user profile in the MAXI DOT

›

display.

If there is no free space available to create a new user profile, delete an existing

user profile.

During the connecting procedure, no other mobile phone may be connected with

the hands-free system.

Up to four mobile phones can be paired with the hands-free system, whereby on-

ly one mobile phone can communicate with the hands-free system.

The visibility of the hands-free system is automatically switched off 3 minutes af-

ter the ignition is switched on and is also deactivated when the mobile phone has

connected to the hands-free system.

Restoring the visibility of the hands-free system



If you have not managed to connect your mobile phone with the hands-free sys-

tem within 3 minutes of switching on the ignition, the visibility of the hands-free

system can be reestablished for 3 minutes in the following ways.

By turning the ignition off and on.

›

By turning voice control off and on.

›

In the Bluetooth - Visibility menu in the MAXI DOT display.

›

Creating a connection with an already paired mobile phone

After switching on the ignition, the connection is automatically established for

the already paired mobile phone2). Check on your mobile phone if the automatic

connection has been established.



Depending on the Bluetooth® version on the mobile phone, an automatically generated 6-digit PIN is either displayed or the PIN 1234 has to be entered manually.

Some mobile phones have a menu, in which the authorisation for establishing a Bluetooth® connection is completed by inputting a code. If the authorisation input is required, it must always be performed when re-establishing the Bluetooth connection.

Communication and multimedia

Disconnecting the connection

By withdrawing the ignition key.

›

By disconnecting the hands-free system in the mobile phone.

›

By disconnecting the user in the Bluetooth - Users menu item in the MAXI DOT

›

display.

Solving connection problems Check the operating status of the mobile phone if the system reports No paired

phone found.

Is the mobile phone switched on?

›

Is the PIN code entered?

›

Is Bluetooth® active?

›

Is the visibility of the mobile phone active?

›

Has the mobile phone already been paired with the hands-free system?

›

Note

■

If a suitable adapter is available for your mobile phone, only use your mobile phone in the adapter inserted in the telephone mount so that the radiation in the vehicle drops to a minimum.

■

Placing the mobile phone in the adapter inserted in the telephone mount ensures optimum sending and receiving power.

Symbols in the MAXI DOT display

First read and observe the introductory information given on page 86.



Symbol Meaning

 Charge status of the phone battery







 A multimedia unit is connected to the hands-free system.

This function is only supported by some mobile phones.

Signal strength a phone is connected to the hands-free system. The hands-free system is visible to other devices.

Telephone operation in the MAXI DOT display

First read and observe the introductory information given on page 86.



The following menu items can be selected from the Phone menu.

■

Phone book

■

Dial number

■

Call lists

■

Voice mailbox

■

Bluetooth

■

Settings

■

Back

Phone book

The Phone book menu item lists the contacts downloaded from the telephone memory and the mobile phone SIM card.

Dial number

Any telephone number can be entered in the Dial number menu item. The required numbers must be selected one after the other using adjustment wheel and confirmed by pressing the adjustment wheel. You can select digits 0-9, sym-



bols , , , # and the Cancel, Call and Delete functions.

Call lists The following menu items can be selected in the Call lists menu item.

■

Missed calls

■

Dialled numbers

■

Received calls

Voice mailbox

In the Voice mailbox menu item, you can set the number of the voice mailbox and then dial the number.

Bluetooth The following menu items can be selected from the Bluetooth menu item.

■

User - Overview of the stored users

■

New user - Search for new mobile phones in reception range



■

Visibility - Switches on the visibility of the phone for other devices



On vehicles fitted with the Amundsen+ navigation system, this function can be accessed via the navigation system menu; refer to the » Operating instructions for the Amundsen+ navigation system.

This function is not available in vehicles fitted with the Amundsen+ navigation system.

Using the system

■

Media Player

■

Active device

■

Paired devices

■

Phone name - option to change the name of the phone (default SKODA_BT)

Settings The following menu items can be selected from the Settings menu item.

■

Phone book

■

Update

■

List

■

Surname

■

First name

■

Ring tone

Back

Return in the Start menu of the telephone.

Voice control



Introduction

This chapter contains information on the following subjects: Dialogue 91

Voice commands 92

Dialogue

First read and observe the introductory information given on page 91.



The period of time during which the system is ready to receive voice commands and to carry them out is called a dialogue. The system gives audible feedback and guides you if necessary through the relevant functions.

Optimum understanding of the voice commands depends on several factors.

Speak with a normal tone of voice without intonation and excessive pauses.

›

Avoid a bad pronunciation.

›

Close the doors, windows and sliding roof, to reduce or stop disturbing exterior

›

noise. It is recommended to speak louder at higher speeds, so that the tone of your

›

voice is louder than the increased surrounding noise. During the dialogue, limit additional noise in the vehicle, e.g. passengers talking

›

at the same time. Do not speak, if the system makes an announcement.

›

The microphone for voice control is inserted in the moulded headliner and directed to the driver and front passenger. Therefore the driver and the front passenger can operate the equipment.

Entering a phone number

The telephone number can be entered as a continuous series of individually spo-



ken digits (the whole number at once) or in the form of digital blocks (separated by short pauses). After each order of digits (separation through brief voice pause) all of the digits detected up to now are repeated by the system.

The digits 0 - 9, symbols +, , # are permitted. The system detects no continuous digit combinations such as twenty-three, but only individually spoken digits (two, three).

Switching on voice control

Press the  button on the adapter » Fig. 83 on page 89 briefly.

›

Press the

›



erating the phone on the multifunction steering wheel .

Switching off voice control

If the system is currently playing a message, the message that is currently being played will have to be stopped as follows:

Press the

›

Press the

›

If the system is expecting a voice command, you can end the dialogue yourself as follows.

with the CANCEL voice command.

›

Press the

›

Press the

›

button on the multifunction steering wheel briefly » page 87, Op-



button on the adapter briefly.

button on the multifunction steering wheel briefly.



button on the adapter.

button on the multifunction steering wheel briefly.



On vehicles fitted with the Amundsen+ navigation system, this function can be accessed via the navigation system menu; refer to the » Operating instructions for the Amundsen+ navigation system.

Communication and multimedia

Note

■

The dialogue of an incoming call is immediately interrupted.

■

The voice control is only possible in vehicles fitted with a multifunction steering wheel with telephone control or a phone mount and adapter.

Voice commands

First read and observe the introductory information given on page 91.



Basic voice commands

Voice command Action

HELP

CALL XYZ

PHONE BOOK

CALL REGISTER Lists of dialled numbers, missed calls, etc.

DIAL NUMBER

REDIAL

MUSIC

FURTHER OPTIONS

SETTINGS Selection for setting Bluetooth®, dialogue etc.

CANCEL The dialogue is ended.

On vehicles fitted with the Amundsen+ navigation system, this function can be accessed via the navigation system menu; refer to the » Operating instructions for the Amundsen+ navigation system.

If a voice command is not detected, the system answers with “Sorry?”, and a new attempt can be made. After the 2nd error the system repeats the aid. After the 3rd failed attempt the answer “Cancelled” is given and the dialogue is ended.

After this command the system repeats all possible commands.

This command calls up the contact from the phone book.

After this command, for example, the phone book can be repeated back to you, a voice entry for the contact can be updated or deleted, etc.

After this command, a telephone number can be entered to establish a connection with the requested party.

After this command the system calls the last dialled number.

Play music from the mobile phone or another paired device.

After this command the system offers additional context-dependent commands.

Store voice recording of a contact

If automatic name recognition does not work reliably for some contacts, you can choose to save your own voice tag for the contact in the Phone book - Voice tag Record menu item.



Your own voice tag can also be saved using the voice control in the FURTHER OPTIONS menu.

Multimedia

 Introduction

This chapter contains information on the following subjects: Music playback via Bluetooth

Operating the radio and navigation system on the multifunction steering wheel 93

AUX and MDI inputs

Music playback via Bluetooth

First read and observe the introductory information given on page 92.



The universal telephone preinstallation GSM II makes it possible to play back music via Bluetooth® from the devices such as MP3 player, mobile phone or notebook.

To ensure the music can be played back via Bluetooth®, you must first pair the device with the hands-free system in the Phone - Bluetooth - Media player menu.

The music playback process is performed on the connected device. The universal telephone preinstallation GSM II ensures that the music played back

via the hands-free system can be controlled with the remote control » page 92, Voice commands.

Note

The device being connected must support the Bluetooth the operating instructions for the relevant device being connected.

A2DP profile; refer to



Using the system

Operating the radio and navigation system on the multifunction steering wheel

Fig. 84

Multifunction steering wheel: Control buttons and wheel

First read and observe the introductory information given on page 92.

The radio and navigation system can of course still be operated on the devices. A description is included in the relevant operating instructions.

If the side lights are switched on, the buttons on the multifunction steering wheel are illuminated.

The buttons apply for the respective operating mode of the current radio or navigation system.

The following functions can be completed by pressing or turning the buttons.



The multifunction steering wheel has buttons for operating the basic functions of factory-fitted radio and navigation system » Fig. 84.

Button/

wheel » Fig. 84

1 1

Action Radio, traffic information CD/MP3/Navigation

Press briefly Switch off/on tone

Press button for a

long period of time

Turn upwards Increase the volume

Turn downwards Decrease volume

Press briefly

Press button for a

long period of time

Press briefly

Press button for a

long period of time

Change to the next preset radio station

Interruption of the traffic report

Search forwards Fast forward

Change to the previous preset radio station

Interruption of the traffic report

Search backwards Fast rewind

Switch the unit on/off

Changing to the next title

Changing to the previous title

Communication and multimedia



Note

■

The functions of button 1 are different for vehicles fitted with a universal telephone preinstallation GSM II » page 87.

■

The loudspeakers in the vehicle are adjusted to the power output of the radio and navigation system of 4x20°W.

AUX and MDI inputs

First read and observe the introductory information given on page 92.



The AUX input is located below the front armrest and is marked with The MDI input (AUX and USB) is located at the front under the storage compart-

ment on the passenger side. The AUX- and MDI inputs are used to connect external audio sources (e.g. iPod or

MP3 player) and to play back music from these devices via the factory-fitted radio or navigation system.

For a description of use, refer to the operating instructions for the relevant radio or navigation system.





Using the system

Driving

Starting-off and Driving

Steering

 Introduction

This chapter contains information on the following subjects: Adjusting the steering wheel position

Power steering 95

WARNING

■

When driving, hold the steering wheel with both hands firmly on the outer edge in the 9 o'clock and 3 o'clock position. Never hold the steering wheel in the 12 o'clock position or in any other way (e.g. in the middle or inner edge of the steering wheel). In such cases, you could severely injure your arms, hands and head when the driver airbag is deployed.

■

Never adjust the steering wheel when the vehicle is moving only when the vehicle is stationary!

■

Adjust the steering wheel so that the distance 1 » Fig. 85 on page 95 between the steering wheel and your chest is at least 25 cm. Not maintaining this minimum distance will mean that the airbag system will not be able to properly protect you - there is a risk that you could be killed.

■

If the steering wheel is adjusted further towards the head, the protection provided by the driver airbag in the event of an accident is reduced. Check that the steering wheel is aligned to the chest.

Adjusting the steering wheel position

Fig. 85 Adjustable steering wheel: Lever below the steering column/safe distance to the steering wheel

First read and observe the introductory information and safety warnings on page 95.



The height and forward/back position of the steering wheel can be adjusted.

First of all adjust the driver's seat » page 54, Front seats.

›

Pull the lever below the steering wheel down » Fig. 85 - .

›

Adjust the steering wheel to the desired position (with regard to the height and

›

forward/back position). Push the lever upwards to the stop.

›

WARNING

The lever for adjusting the steering wheel must be locked while you are driving so that the position of the steering wheel cannot accidently change during the journey – there is the risk of an accident.



Power steering

First read and observe the introductory information and safety warnings on page 95.



The power steering enables you to steer the vehicle with less physical force. The power steering only works when the engine is running.





Starting-off and Driving

It is still fully possible to steer the vehicle if the power steering fails or if the engine is not running (e.g. when towing). However, greater physical effort is required to turn the steering wheel.

CAUTION

You will place great stresses on the power steering system if the steering is turned to full lock when the vehicle is stationary. Turning the steering to full lock in such a situation will be accompanied by noises. Never leave the steering wheel at full lock for more than 15 seconds when the engine is running - there is a risk of damaging the power steering.

Starting and stopping the engine



Introduction

This chapter contains information on the following subjects: Electronic immobilizer

Ignition lock 97 Starting the engine Switching off the engine

The engine can only be started using a correctly coded original key. The engine running noises may louder at first be louder for a short time after

starting the cold engine. This is quite normal and is not an operating problem.

WARNING

■

When the vehicle is travelling with the engine off, the ignition key must always be in position 2 » Fig. 86 on page 97 (ignition switched on). This position is indicated by the warning lights coming on. If this is not the case, it could result in unexpected locking of the steering wheel – there is the risk of an accident.

■

Only pull the ignition key from the ignition lock when the vehicle has come to a complete stop (by applying the handbrake). Otherwise the steering wheel could lock – there is the risk of an accident.

WARNING (Continued)

■

When leaving the vehicle, the ignition must always be removed. This is particularly important if children are left in the vehicle. Otherwise the children could, for example, start the engine – there is the risk of an accident or injury.

■

Never leave the vehicle unattended with the engine running.

■

Never switch off the engine before the vehicle has come to a halt – there is the risk of an accident.



WARNING

■

Never leave the engine running in unventilated or closed rooms. The engine's exhaust gases also contain the odourless and colourless carbon monoxide, a poisonous gas – risk of death.

■

Carbon monoxide can cause unconsciousness and death.

CAUTION

■

The starter must only be operated when the engine is not running and the vehi-

cle is at a standstill. The starter or engine can be damaged if the starter is activated when the engine is running 3 » Fig. 86 on page 97.

■

If the engine does not start up after a second attempt, the fuse for the fuel

pump may have a fault. Check the fuse and replace, if necessary » page 192 or seek assistance from a specialist garage.

■

Let go of the ignition key as soon as the engine starts otherwise the starter

could be damaged.

■

Do not tow start the engine – there is a risk of damaging the engine and the

catalytic converter. The battery from another vehicle can be used as a jump-start aid » page 187, Jump-starting.

CAUTION

■

Avoid high engine speeds, full throttle and high engine loads until the engine

has yet reached its operating temperature – there is a risk of damaging the engine.

■

Do not switch the engine off immediately at the end of your journey after the

engine has been operated over a prolonged period at high loads but leave it to run at an idling speed for about 1 minute. This prevents any possible accumulation of heat when the engine is switched off.



Driving

For the sake of the environment

Do not warm up the engine while the vehicle is stationary. If possible, start your journey as soon as the engine has started. Through this the engine reaches its operating temperature more rapidly and the pollutant emissions are lower.

Note

The radiator fan can intermittently continue to run for approximately 10 minutes after the ignition has been switched off.

Electronic immobilizer

First read and observe the introductory information and safety warnings on page 96.



An electronic chip is integrated in the head of the key. The immobiliser is deactivated with the aid of this chip when the key is inserted in the ignition lock. The electronic immobiliser is automatically activated when the ignition key is withdrawn from the lock.

The engine will not start if a non-authorized ignition key is used. The MAXI DOT display shows the following:

Immobilizer active.

First read and observe the introductory information and safety warnings on page 96.



Petrol engines » Fig. 86

Ignition switched off, engine off, the steering can be locked

Ignition switched on

Starting engine

Diesel engines » Fig. 86



Fuel supply interrupted, ignition switched off, engine switched off, the steering can be locked.

Heating glow plugs on, ignition switched on

Starting engine

To lock the steering, with the ignition key withdrawn, turn the steering wheel

until the steering locking pin engages audibly.

If the steering is locked and the key cannot be turned or can only be turned with

difficulty to position

steering lock will unlock.

» Fig. 86, move the steering wheel back and forth and the

Note

We recommend locking the steering wheel whenever leaving the vehicle. This

acts as a deterrent against the attempted theft of your car.



Ignition lock

Fig. 86

Positions of the vehicle key in the ignition lock

Starting the engine

First read and observe the introductory information and safety warnings on page 96.



Vehicles with a diesel engine are equipped with a glow plug system. The glow

plug warning light  lights up after the ignition has been switched on. Start the

engine once the  warning light has gone out.

You should not switch on any major electrical components during the heating pe-

riod otherwise the vehicle battery will be drained unnecessarily.

Procedure for starting the engine

Move the gearshift lever into neutral or move the selector lever to position P or

›

N and firmly apply the handbrake.

Switch on the ignition 2 » Fig. 86 on page 97.

›

Starting-off and Driving



Škoda Fabia 2013 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Layout of this Owner's Manual (explanations)

Documentation of vehicle handover

Preface

Table of Contents

Materials defect liability and ŠKODA warranty for new cars

Mobility warranty and ŠKODA extended warranty

Abbreviations

Using the system

Cockpit

Overview

Instruments and Indicator Lights

Instrument cluster

Introduction

Overview

Engine revolutions counter

Speedometer

Coolant temperature gauge display

Fuel gauge

Counter for distance driven

Digital clock

Display of the second speed

Recommended gear

Multifunction display (MFD)

Introduction

Memory

Operation

Multifunction display details

Warning against speeding

Service Interval Display

Introduction

Prompt in the segment display

Display in the MAXI DOT display

MAXI DOT display

 Introduction

Main menu

Settings

Door, boot lid and bonnet warning

Auto Check Control

Warning lights

Introduction

Handbrake

Brake system

Seat belt warning light

Alternator

 Door open

Engine oil

  Coolant

 Power steering

Electronic Stability Control (ESC)

Traction Control System (ASR)

 Antilock brake system (ABS)

The rear fog light

Bulb failure

 Exhaust inspection system

Glow plug system (diesel engine)

 ECU fault light (petrol engine)

Diesel particulate filter (diesel engine)

Fuel reserve

 Airbag system

 Windscreen washer fluid level

Traction control (TCS) switched off

 Tyre pressure

Turn signal system

Low beam

 Fog lights

Cruise control system

 Selector lever lock

 Main beam

Unlocking and locking

Unlocking and locking

Introduction

Vehicle key

Replacing the battery in the remote control key

Child safety lock

Opening/closing the door

Locking/unlocking the vehicle without central locking