Skimo Split 320B05,Split 320B06,Split Heater 320B51 Installation, User And Maintenance Manual

Société Nouvelle De Climatisation

274, chemin des Agriés – 31860 LABARTHE SUR LEZE

Tél. : [phone] - Fax : [phone]

Ce document est la propriété de SNDC SAS – Il ne peut être ni reproduit, ni communiqué sans autorisation de SNDC SAS.

This document is the property of SNDC SAS – It can neither be reproduced, nor communicated without SNDC SAS's written authorization.

Version 3 – 30/06/15 810C37-EN-MANUTMAIN

EN

INSTALLATION, USER AND MAINTENANCE MANUAL

SKIMO SPLIT

EN

PART NUMBER : 320B05 – SKIMO SPLIT 12V

320B06 – SKIMO SPLIT 24V

EN

Read this manual carefully until you understand it before unpacking, installing or using the Skimo unit.
Keep this manual for further reference.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

2/22

The 2 years warranty only applies under normal operation of the SKIMO A/C unit.
* Limited warranty
The warranty doesn’t cover damages resulting from an incorrect operation of the SKIMO A/C unit, particularly for the following cases :

 Operating in an environment with high salinity.
 Operating in an environment with high acidity.
 Cleaning with a pressure washer and/or with detergents.
 Consumable parts (filters) or considered as wear parts are also excluded from warranty.

TABLE OF CONTENTS

Section

Title

Page

1

INTRODUCTION

3

2

SECURITY INSTRUCTIONS AND WARNINGS

3

3

TECHNICAL CHARACTERISTICS OF THE KIT SKIMO SPLIT

4

4

KIT SKIMO SPLIT DESCRIPTION

6

5

BEFORE FITTING THE KIT SKIMO SPLIT

7

6

FURNITURE REQUIRED TO INSTALL THE KIT SKIMO SPLIT

8

7

PREPARATION OF THE KIT SKIMO SPLIT

8

8

CABIN WALLS PREPARATION TO RECEIVE THE UNITS

9

9

INSTALLATION OF THE KIT SKIMO SPLIT

10

10

ELECTRICAL CONNECTION

11

11

REFRIGERATED CONNECTING OF THE KIT SKIMO SPLIT

12

12

CHARGE THE KIT SKIMO SPLIT WITH REFRIGERANT R134A

13

13

ELECTRICAL DRAWING

14

14

KIT SKIMO SPLIT USE

15

15

REPAIRS

15

16

MAINTENANCE

17

17

EXPLODED VIEWS AND SPARE PARTS LIST

18

18

APPENDIX AND REVISIONS

22

If you have any question regarding the installation and use of the kit SKIMO SPLIT, please contact our quality service:

[phone]

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

3/22

1. INTRODUCTION

The KIT SKIMO SPLIT described in this manual, is composed of an outside unit SKIMO SPLIT and an evaporator unit to
be positioned inside the cabin. The compressor - condenser unit can be installed horizontally on a wall or flat on a hood

(see pictures).

The kit SKIMO SPLIT is particularly adapted to the compact machines with little room or a small driving power, to the
machines the cabin of which is far from the engine and to the users wishing a fast and easy assembly.
The SKIMO SPLIT unit has the compressor integrated and driven by an electric motor.
2 units will be linked between them by 2 hoses (high and low pressure) and electrically by a harness.
( See the recommendations on the power supply with the rest of the vehicle).
The charge of regrigerant R134a will be made by a qualified and approved technician.

2. SECURITY INSTRUCTIONS AND WARNINGS

You must read and understand this manual before proceeding to the installation, set-up, use and maintenance of
the kit SKIMO SPLIT.

List of pictograms used in this manual or on the unit:

Pictogram

Meaning

Pictogram

Meaning

Conform to CE standard

General danger

Read and understand the manual

Physical danger

Important information

The kit SKIMO SPLIT must be installed by a person qualified and adequately equipped. All alteration of the unit or
incorrect installation are strictly forbidden and can be dangerous. SNDC SAS cannot be held responsible in the case of
physical or material damages due to an alteration, installation or use that is different to that described in this manual

The SKIMO SPLIT unit weights approximately 30 kg. Take necessary precautions when handling, installing and
using the unit to avoid any risk of injury, fall or damage. Do not handle or install the SKIMO SPLIT unit on your own.

Do not store, install or use the kit SKIMO SPLIT close by flammable liquids, gas or solids, or close by a heat source
or in a place presenting risks of explosion or fire.

If the kit SKIMO SPLIT is damaged, it must not be used or turned on. It must be repaired or replaced first.

Flat mounting

Horizontal mounting

With horizontal

mounting only the

connectings on

the TOP

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

4/22

If repairs or maintenance operations are required on the kit SKIMO SPLIT, use a qualified company using qualified
personnel to perform the operations. Any repair or maintenance operation that is not done properly can create risks of
danger. Do not try to repair the SKIMO SPLIT by your own means if you are not qualified. For the charge or maintenance
of the A/C refrigerant circuit, use a qualified company that is equipped with appropriate tools and security equipment and
that uses original spare parts.

Do dot alter cabins that are certified « FOPS-ROPS »

In case of fire, do not open the unit cover. Extinguish the fire with an appropriate fire extinguisher for electrical
and A/C units.

Contact the vehicle or machine supplier to enquire of the necessary changes regarding the papers (height of
vehicle, weight…). Perform any necessary changes.

Always turn the kit SKIMO SPLIT and the vehicle or machine off before an operation of maintenance.

Disconnect all the electrical connections to the machine before fixing, or repairing the kit SKIMO SPLIT or before
any operation that could involve getting in contact with the electrical circuit.

Do not introduce foreign objects inside the SKIMO SPLIT unit.

The kit SKIMO SPLIT contains moving parts that represent a danger. Do not disable the security features. Switch

the SKIMO SPLIT unit and the machine or vehicle off before opening the unit or taking the cabin panel off.

The A/C refrigerant circuit is under pressure. Do not open the A/C refrigerant circuit. This would create a loss of
refrigerant gas that is colourless and odourless. It could create serous burns. The personal performing the repair or
maintenance of the A/C refrigerant circuit must be qualified to manipulate such systems and must use appropriate tools,
equipment and protection equipment. Wear protection goggles and gloves when you maintain the SKIMO SPLIT unit.
Rejecting refrigerant gas in the atmosphere is strictly forbidden.

The kit SKIMO SPLIT must be maintained and cleaned up regularly from dust, vegetal or other wastes or
combustibles to avoid risks of fire.

Use only original spare parts.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

5/22

3. TECHNICAL CHARACTERISTICS OF THE KIT SKIMO SPLIT

The SKIMO SPLIT unit is the element positioned outside, it includes the following components : the condenser, the drying
filter, the compressor, the electric components (electrical motor, fan, blower, harness, fuses), but also the electric
harness of connection with the vertical evaporator unit positioned inside the cabin.

 External dimensions:

o SKIMO SPLIT unit (+ ou - 1cm) : lengh 69 cm, width 42 cm, height 20.5 cm
o Vertical evaporator unit (+ ou 1 cm) : lengh 41 cm, width 15.5 cm, height 41.5 cm.

 Weight :

o SKIMO SPLIT unit 30 kg
o Vertical evaporator unit 10 kg

 Evaporator cooling capacity: 2900 W with +31°C air intake and 50% air humidity.
 Maximal consumption: 960W (that is 80 Amps electrical current for a 12V unit and 45 Amps for a 24V unit.
 Refrigerant HFC R134a quantity : according to the position of the outside SKIMO SPLIT unit (see board in chapter

number 12)

 Oil: SP10 ISO 46 (SNDC Ref 430A09) (see board in chapter number 12)

205

420

688

414

155

410

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

6/22

4. KIT SKIMO SPLIT DESCRIPTION

N° DESCRIPTION

1. Condenser ventilator

2. SKIMO SPLIT cover

3. Ouside air intake grids

4. Drying filter

5. SKIMO SPLIT casing

6. M8 unit fastening screws (4)

7. Seal box of fuses and relays

8. Electric motor

9. Compressor

10. LOW-PRESSURE connect

11. HIGH-PRESSURE connect

12. Electrical harness

13. Control and air distribution plenum

14. Control panel

15. Air filter access grid

16. Grid fastening screws

17. Vertical evaporator unit fixations

18. Adjustable air louvers

19. Default signal light

20. A/C and ventilation speed selector switch

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

7/22

5. BEFORE FITTING THE KIT SKIMO SPLIT

Prior to fitting and using the kit SKIMO SPLIT, check the following points:

Cabin volume: Ideally the volume of the cabin is approximately 2m3 but if it is over 3m3 the performances of the SKIMO
SPLIT system will decrease.

Cabin insulation: The cabin walls must be properly insulated, especially from important heat sources (engine, exhaust
pipe, hydraulic system …). SNDC SAS cannot be held responsible in the case of poor performances of the SKIMO SPLIT
system caused by poor cabin insulation.

Electrical power:
The machine or vehicle engine must be equipped with an alternator able to supply the electrical power
required from the vehicle or machine AND from the KIT SKIMO SPLIT. The SKIMO SPLIT system maximal
consumption is 960W (80 Amps for a 12V unit or 40 Amps for a 24V unit). If the vehicle or the machine is
equipped with an alternator that is not powerful enough, it must be replaced by a suitable alternator.

Roof and ceiling:
Do not alter or make a hole in the cabin of vehicles that are certified « FOPS-ROPS »
The walll must be stiff and strong enough for the Skimo SPLIT unit to be installed on. If it is not the case, the
wall must be reinforced.
The SKIMO SPLIT unit must not be installed if it would affect the stability of the vehicle or machine it is
installed on, or if it would create excessive strains on its structure.
Make sure using the drawing showing the dimensions of the unit and the cut-out area that there is enough
space to fit the unit outside on the wall and the vertical evaporator unit n panel inside the cabin.
The surface on which unit is installed must be flat and horizontal (+/- 5°).
The cabin panel must be installed inside the cabin, and the user must be able to access the controls from his
driving position while using the vehicle or machine.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

8/22

6. FURNITURE REQUIRED TO INSTALL THE KIT SKIMO SPLIT

 Two 16 mm

2

(12V) or 10mm² (24V) diameter cables to connect SKIMO to the vehicle’s battery : a black one for

the ground and a red one for the positive, fitted with M6 crimp terminals on the SKIMO’s end and crimp terminals
on the battery’s end (according to the battery’s connection type, generally M10)

Caution: Maximum cable length: 5 m

 One 1 mm

2

diameter cable to connect SKIMO to the D+ signal (“engine
running”) of the alternator, with a 1 way FASTON connector (male housing,
female contact) and a connector on the other end to connect to the D+ signal
coming from the alternator.

 A fuse holder and a 100Amps (12Volts) or 50Amps (24Volts) fuse.

The above mentioned components are available as a connection optional set, reference 274B56 (12Volts) or 274B58
(24Volts)

7. PREPARATION OF THE SKIMO SPLIT

1. Open the cardboard of the SKIMO SPLIT unit.

2. Remove the foam protection surrounding the 2 units.

3. Take the SKIMO SPLIT unit, remove the 4 screws of the cover to reach in the 4 unit fastening screws

4 unit

fastening

holes

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

9/22

8. CABIN WALLS PREPARATION TO RECEIVE THE UNITS

Preparation for fastening the SKIMO SPLIT unit

Dimensions en millimeters (mm)

Drill in the chosen wall 4 holes in diameter 10 mm according to the plan of setting-up above.

Preparation for fastening the vertical evaporator unit

Dimensions en millimeters (mm)

Drill in the chosen wall 4 holes in diameter 8 mm according to the plan of setting-up above.

4 holes

4 holes

CABIN FLOOR

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

10/22

9. INSTALLATION OF THE KIT SKIMO SPLIT

The SKIMO SPLIT unit is heavy (approximately 30 kg). Take necessary precautions to avoid hurting

yourself or damaging the unit. Never install the unit on your own.

Location of the SKIMO SPLIT unit

Fix the SKIMO SPLIT unit to the wall by means of the supplied stainless screws 4 HM8-20 + 8 flats M8 and 4 slices EPDM

8.5x20mm and 4 nuts HM8.

Access of the 4 fastening unit

Nut HM8

Flat M8

Screw HM8-20

EPDM slice

Inside of the

SKIMO SPLIT

Wall vehicle

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

11/22

Location of the vertical evaporator unit

Fix the vertical evaporator unit to the wall by means of the supplied stainless screws 4 HM6-25 + 8 flats M6 and 4 nuts
HM6.

10. ELECTRICAL CONNECTION

The installer must make sure that the cables are insulated and protected from any risk of deterioration

or tear-up (from branches for example) and that they do not present any risk for people or appliances.

The passage of electric cables will be made on the side of the unit.

Inside the cabin

Exit electric harness

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

12/22

Do not lay the cables out near the motor and compressor belt located at the back of the unit.

Once the cables laid out, connect them as follows to the SKIMO unit electrical motor:

1. Take the 2 nuts of the motor (+)
terminal off. Insert the red cable
through the rubber cover.

2. Screw the nuts back on onto the red
cable and red wires crimp terminals
and the washer.

3. Put the rubber cover back into
place. Repeat 1 and 2 on the motor (-)
terminal with the ground black cable
and wires.

4. Connect the cables to the battery or to the alternator. The fuse housing with its fuse (100Amps for 12Volts, 50 Amps
for 24Volts) must be fitted on the red positive cable less than 15cm away from the crimp terminal connected to the (+)
terminal of the battery or of the alternator.

Caution: The positive (+) cable MUST be protected by a 100Amps (12V) or 50 Amps (24 V) fuse located

as close as possible to the power source.

Make sure that the section of the cables between the battery and the alternator is big enough for the
current required by the SKIMO SPLIT (80 Amps for the 12Volts unit, 40 Amps for the 24Volts unit) and by the
other electrical equipments of the vehicle.

5. Connect the 1-way FASTON located inside the cabin to the D+ signal from the alternator (signal indicating that the
engine is running) with a 1mm² section cable.

6. Plug the ventilator connector back and fasten unit cover back on with its 4 screw.

11. REFRIGERATED CONNECTING OF THE KIT SKIMO SPLIT

Connect the SKIMO SPLIT unit and the vertical evaporator unit by 2 hoses with oring steel fittings to be determined by
the customer:

A flexible hose M6, high pressure, connecting the entrance of the evaporator unit to the entrance of the SKIMO SPLIT
unit.

A flexible hose M10, low pressure, connecting the exit of the SKIMO SPLIT unit with the exit of the vertical evaporator
unit.

Lubrificate lightly each Oring with the same oil SP10 or PAG 46 than for the compressor before
connecting any fitting.
Make sure the hoses be correctly connected, so as not to be in contact with cutting parts or heat source.
When flexible hoses cross a wall, it’s necessary to use one thread rubber or adapted protective plastic ducts.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

13/22

12. CHARGE THE KIT SKIMO SPLIT WITH REFRIGERANT R134a AND OIL

Complete the unit with 30 cc of SP10 ISO 46 oil.

The charge of R134a of the kit SKIMO SPLIT will be a function:

 Of the position of the SKIMO SPLIT unit outside.
 Of the total length in flexible hose.

Position SKIMO SPLIT unit

Length flexible
hoses

Flat

Horizontally

2 meters

480 g

480 g

4 meters

500 g

500 g

6 meters

550 g

550 g

For the charge or maintenance of the A/C refrigerant circuit, use a qualified company that is equipped
with appropriate tools and security equipment and that uses original spare parts.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

14/22

13. ELECTRICAL DRAWING

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

15/22

14. KIT SKIMO SPLIT USE

The SKIMO SPLIT is designed to run when the vehicle’s engine is running. If the unit is turned on while
the vehicle’s engine is off, the alternator will not feed the unit and there is a risk of battery discharge.

The ability of the SKIMO SPLIT to maintain the required temperature inside the cabin depends on the amount of
heat that penetrates inside the cabin. Some preventive measures are necessary to lower the amount of heat that enters
the cabin and to improve the performances of A/C system :

- Park the machine or the vehicle in the shade.

- Drive for a few minutes with the windows opened to lower the temperature inside the cabin before turning the

A/C unit on.

- Keep the doors and windows closed while using the A/C unit.

- Avoid using devices that produce heat.

Operating modes:

- Once the kit SKIMO SPLIT is installed and the vehicle’s engine is running, turn the control panel ventilation speed
selector switch to first speed to turn the unit on. The first ventilation speed and the air conditioning are turned on.

- Adjust the ventilation speed to 1, 2 or 3 according to your requirement with the ventilation speed selector switch.

- To switch the unit off, turn the ventilation speed selector switch to 0.

Switch the kit SKIMO SPLIT off if the vehicle’s or machine’s engine runs on low speed for an extended amount of
time (for over 15 minutes). If not, there is a potential risk of battery discharge due to the fact that the alternator might
not supply enough power when the engine runs at low speed. The SKIMO SLIT unit would turn to security mode. If that
happens, refer to section 15.

It is normal for the internal thermostat to regulate the A/C unit if the blowing temperature is too low, in which case
the blowers still run but the air conditioning is turned off for a while.

SNDC SAS cannot be held responsible for condensation appearing on the cabin’s surfaces. The air contains moisture

that tends to condensates on cold surfaces. Appropriate cabin insulation can prevent or lover the risks of condensation.

15. REPAIRS

If the A/C circuit hasn’t got the correct amount of gas, the performances of the A/C system will lower. If it seems
that your SKIMO SPLIT unit doesn’t work properly, you should take it to an A/C specialist.

Never try to repair faults by your own means. Repair and recharge of an A/C circuit must be carried out

by a specialist that is qualified, certified, equipped with necessary tools and that will use original spare parts.

If one of the security systems is activated, the air conditioning system is turned off (no more cold production) and the
default light is switched on on the control panel.
To reset the Skimo A/C unit after a security cut off, turn it off and on again. A security cut off
should not be a recurring feature. In the case of repeated cut offs, contact your qualified
specialist.

Révision D

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

16/22

Error codes:

Error code

Failure

Repair required

1 blink

Overheating of the electrical motor. The
temperature of the motor went over 113°C.
The unit can be reset by switching it off and

on again only once the motor’s temperature

is lower than 109°C

Check that the air way cooling the electrical motor is
not clogged up.

To be done by an A/C specialist:

Check that the A/C circuit hasn’t got too much

gas R134a.

2 blink

The battery is flat. The tension of the battery
went lower than 9.5V (for a 12V unit) or 14V
(for a 24V unit)

Check that the battery gets charged up properly and
that the alternator is powerful enough. Check that

the vehicle’s engine doesn’t run at low speed for

extended periods of time (over 15 minutes)

3 blink

Over consumption of the electrical motor

Check the power consumption of the SKIMO SPLIT.

To be done by an A/C specialist:

Check that the A/C circuit hasn’t got too much

gas R134a.

5 blink

High voltage. The tension of the battery went
over 18V (for a 12V unit) or 32V (for a 24V
unit)

Check that the alternator supplies its nominal
voltage, and that the nominal tensions of the
alternator, of the battery and of the SKIMO SPLIT
are identical.

6 blink

Low voltage. The tension of the battery went
lower than 10.5V (for a 12V unit) or 21V (for
a 24V unit).

Check that the battery gets charged up properly and
that the alternator is powerful enough. Check that

the vehicle’s engine doesn’t run at low speed for

extended periods of time (over 15 minutes)

Light on
continuously

A/C system gas low pressure. The pressure
switch is activated for a pressure lower than
2 bars in the high pressure part of the circuit
in case of the quantity of gas being too low
(caused by a leak for example).

To be done by an A/C specialist:
Check the airtightness of the A/C circuit and
recharge with R134a gas.

Light AND
electrical motor
on and off

A/C system gas high pressure. The pressure
switch is activated for a pressure higher than
14 bars in the high pressure part of the
circuit.

Check that the condenser is not clogged up.

To be done by an A/C specialist:

Check that the A/C circuit hasn’t got too much

gas R134a.

Light not on
but unit not
working

The Skimo A/C is not working properly but
the default light is not switched on. This can
be due to an electrical problem.

Check that the default LED light works properly.
Check the fuses, the relays, the electrical harness,
the connectors and the electrical connection
between the Skimo unit and the vehicle or the
machine.

There are two other security systems on the kit SKIMO SPLIT:

Compressor security: The compressor is equipped with a security pressure valve to protect the system in case of a
pressure switch failure.

Machine security: The SKIMO SPLIT unit is equipped with a sensor that disables the SKIMO SPLIT unit if the cover is
opened.

Use only original spare parts.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

17/22

16. MAINTENANCE

The SKIMO SPLIT must be maintained and cleaned up regularly from dust, vegetal or other wastes or
combustibles to avoid risks of fire.
The frequencies listed below are for reference only. The maintenance must be done more frequently if the
working environment can lead to clogging up, premature wear or deterioration of some parts.

The SKIMO SPLIT unit contains parts that are moving that can present a danger. Never disable the
security features. Always turn the unit and the vehicle off before opening the cover or taking the cabin panel
off.

Switch the unit off before any maintenance.

Every 50 hours:

Clean the dust filter
Check the condenser, the ventilator, the main casing. Clean if necessary

In winter:

Turn the Skimo A/C unit on once a week even for a short time (1 minute) to guarantee the lubrication of the seals inside
the A/C circuit.

Every 200 hours:

Check the motor-compressor belt tension:
Tension too high: Risk of premature wear of the compressor bearings.
Tension too low: Risk of premature belt wear.
Replace the air filter (SNDC Ref 281G47).
Check that the water drain holes in the main casing and in the evaporator casing are not clogged up.

Every two years: (To be done by an A/C specialist)
Clean the condenser and the evaporator coils. Clean the water drain holes in the main casing and in the evaporator
casing.
Recover the A/C circuit gas and replace the receiver dryer (SNDC Ref 225A13).
Check the A/C circuit air tightness.
Recharge the circuit and check the thermostat and the pressure switch.
Check the oil level.

Every five years or 2000 hours: (To be done by an A/C specialist)
Check and tighten all the screws and nuts.
Replace the motor-compressor belt.

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

18/22

17. EXPLODED VIEWS AND SPARE PARTS LIST

SKIMO SPLIT unit

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

19/22

Item

12 volts

24 volts

Description

Qty

1

520C23

520C23

Cover SKIMO SPLIT unit

1 2 296C34

296C34

Condenser coil

1 3 520C17

520C17

Support condenser and air plenum

1 5 520C18

520C18

Support condenser

1 6 235L16

235L16

Receiver dryer-condenser A/C hose #6

1 7 235L15

235L15

Condenser-compressor A/C hose #8

1 8 235L14

235L14

Exit unit-compressor A/C hose #10

1

11

540F70

540F71

Electrical motor

1

12

200H05

200H05

Compressor

1

13

560C16

560C16

Motor bracket

1

14

560C26

560C26

Comprressor bracket

1

15

260A40

260A27

Ventilator

1

16

520C16

520C16

Frame SKIMO SPLIT unit

1

17

235L17

235L17

Exit unit-receiver drier A/C hose #6

1

20

274C49

274C50

Electrical box

1

21

264A59

264A59

Pressostat

1

22

233A17

233A17

Receiver drier clamp bracket

1

23

225A13

225A13

Receiver dryer filter

1

24

273D14
273D15

273D14
273D15

Magnetic sensor security

1

26

274B71

274B71

SKIMO SPLIT unit electrical harness

1

27

242C48

242C48

Compresor fitting #10

1

28

274C49

242C49

Compresor fitting #8

1

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

20/22

Vertical evaporator unit

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

21/22

Item 12 volts

24 volts

Description

Qty

1

530C44

530C44

Casing

1 2 530C45

530C45

Plenum

1 3 530C47

530C47

Bracket blower

1 4 530C46

530C46

Air filter access grid

1 5 261A25

261A26

Blower

1 6 294C07

294C07

Evaporator

1 7 530C48

530C48

A/C pipe #6

1 8 250A16

250A16

Expansion valve

1

9

370C44
370B32

350C44
370B32

Adjustable air louvers

5

10

370D43

370D43

Control panel adhesive

1

11

265A37

265A37

Thermostat

1

12

370D44

370D44

Control panel

1

13

234A18

234A18

Grommet 35mm

1

14

690A47

690A47

Specific screw M4-15

1

15

650A07

650A07

Flat washer stainless M22

1

16

243A06

243A06

Nut A/C pipe #10

1

17

650A16

650A16

Flat washer stainless M16

1

18

640A17

640A17

Grower washer stainless M16

1

19

660A20

660A20

Nut A/C pipe #6

1

20

281G47

281G47

Air filter

1

21

274B70

274B70

Electrical harness

1

22

281K41

281K41

Back wall insulation

1

23

281K42

281K42

Side wall insulation

1

24

281K43

281K43

Front wall insulation

1

25

281B80

281B80

Conector DEUTSCH gasket

1

26

281A24

281A24

Wall fitting gasket #10

1

27

281A03

281A03

Wall fitting gasket #6

1

SKIMO SPLIT

PART NUMBER : 320B05 (12V) / 320B06 (24V)

INSTALLATION, USER AND MAINTENANCE MANUAL

22/22

18. APPENDIX AND REVISIONS

Revisions

Version

Date

Objet

0

May 2010

Creation

1

July 2010

Modifications.

2

November 2011

Modify electric drawing.

3

June 2015

Update of the expolded views and the type of oil.