Page 1
Field Reference Guides
GCS900 Scraper
Version 13.13
SITECH Rocky Mountain
www.sitechrockymtn.com
Page 2
Page 3
SITECH TECHNOLOGY DEALER
TRAINING CHECKLIST
System: GCS900 Scraper Version: 13.1
Training Checklist Page #
□
□
□
□
□
□
□
□
□
□
□
□
□
CB460 Control Box Layout 3
Scraper Training Display Settings 4
Check Blade Wear 6
Load Design 7
Verify System Accuracy 8
Vertical Offset 9
Horizontal Offset 10
Vertical Guidance 12
Cut and Fill Site Map 13
Lane Guidance 14
Sensor Calibration 15
Connect to Wi-Fi 16
TCC Settings 17
□
□
□
□
T raining Acknowledgement:
Customer Signature Date SITECH Representative Date
Configure Remote Assistant 18
Wireless Data Sync 19
Start Remote Assistant 20
Connect to IBSS Base 21
CUSTOMER COPY
Page 4
Page 5
SITECH TECHNOLOGY DEALER
TRAINING CHECKLIST
System: GCS900 Scraper Version: 13.1
Training Checklist Page #
□
□
□
□
□
□
□
□
□
□
□
□
□
CB460 Control Box Layout 3
Scraper Training Display Settings 4
Check Blade Wear 6
Load Design 7
Verify System Accuracy 8
Vertical Offset 9
Horizontal Offset 10
Vertical Guidance 12
Cut and Fill Site Map 13
Lane Guidance 14
Sensor Calibration 15
Connect to Wi-Fi 16
TCC Settings 17
□
□
□
□
T raining Acknowledgement:
Customer Signature Date SITECH Representative Date
Configure Remote Assistant 18
Wireless Data Sync 19
Start Remote Assistant 20
Connect to IBSS Base 21
SITECH COPY
Page 6
Page 7
SITECH TECHNOLOGY DEALE
R
Field Reference Guide
Table of Content GCS900 Scraper
Version: 13.1
Field Reference Guide Page #
CB460 Control Box Layout 3
Scraper Training Display Settings 4
Check Blade Wear 6
Load Design 7
Verify System Accuracy 8
Vertical Offset 9
Horizontal Offset 10
Vertical Guidance 12
Cut and Fill Site Map 13
Lane Guidance 14
Sensor Calibration 15
Connect to Wi-Fi 16
TCC Settings 17
Configure Remote Assistant 18
Wireless Data Sync 19
Start Remote Assistant 20
Connect to IBSS Base 21
Page 8
Page 9
R
Page 3
Next Key
Escape / Go Back
Cut / Fill Right
SITECH TECHNOLOGY DEALE
Field Reference Guide
Function Keys (F1-F6) Zoom In - Out
Power Menu USB Port Enter
Cut / Fill Left Horizontal Guidance
Page 10
Page 11
SITECH TECHNOLOGY DEALE
R
Page 4
Field Reference Guide
GCS900 Scraper Training Display Settings
Version: 13.1
The Control Box must be in Manager’s Mode
1. Press “Menu”
2. Select “GNSS Accuracy” and Press “OK”
3. Press and Hold “F6 ” and Press “F2” Medium Mode
4. Change “GPS Horizontal error limit:” to “0.30ft or 0.090m” and Press “Next”
5. Change “GPS Vertical error limit:” to “0.30ft or 0.090m” and Press “OK” Twice
6. Select “Guidance Method” and Press “OK”
7. Use Arrow to change Adjust cut to avoid overcut: to “NO” and Press “OK”
8. Select “Increment Switch Adjustment” and Press “OK”
9. Change Vertical offset increment: “0.00” and Press “OK”
10. Select “Text Items” and Press “OK”
11. Press “F1” and Uncheck each Item checked
12. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order)
13. Press “F3” Cross-Section
14. Press “F1” and Uncheck each Item checked
15. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order)
16. Press “F4” Profile View
17. Press “F1” and Uncheck each Item checked
18. Press “F1” to select “Cut/Fill Left”, “Offline (3D)” and “Cut/Fill Right” (select in order)
19. Press “F5” Text View 1
20. Press “F1” and Uncheck each Item checked
Page 12
21. Press “F1” to select “Design Elev.(3D)”, “Design XSlope (3D)”, “Mainfall (3D)”,
Page 5
“Satellites (3D)” and ”V. GNSS Err (3D)” (select in order)
22.
Press “F6” Text View 2
23. Press “F1” and Uncheck each Item checked
24. Press “F1” to select “Northing (3D)”, “Easting (3D)”, “Elevation (3D)”, “Mainfall” and
“Offline (3D)” (select in order)
25. Press “OK”
26. Select “Save Settings” and Press “OK”
27. Select “Display Settings” and Press “OK”
28. Enter Operator’s Name such as “Joe G” and Press “OK”
29. Press “ESC” twice to return to operating screen
2
Page 13
SITECH TECHNOLOGY DEALE
R
Page 6
Field Reference Guide
GCS900 Check Blade Wear
Version: 13.1
1. Press “Menu”
2. Select “Blade Wear” and Press “OK”
3. Measure from Center of Cutting Edge Bolts to Bottom of Blade
4. Do not use Bolt at Blade Tip
5. Enter Distance and Press “OK”
6. Press “ESC” to return to operating screen
Page 14
SITECH TECHNOLOGY DEALE
R
Page 7
Field Reference Guide
GCS900 Load Design
Version: 13.1
1. Press “Menu”
2. Select “Select Design” and Press “OK”
3. Use Arrows to highlight Design and Press “OK”
4. Press “ESC” to return to the operating screen
Page 15
SITECH TECHNOLOGY DEALE
R
Page 8
Field Reference Guide
GCS900 Verify System Accuracy
Version: 13.1
Verify the system accuracy at the start of each work day using a Permanent Bench Point
1. Move machine to Bench Point with the Blade low to the ground
2. Position Blade Tip over Bench Point
3. Press “Next” until Text Screen 2 is displayed
4. Verify correct Blade Tip is selected Press “F1” to change Blade Tip
5. Verify Northing, Easting and Elevation are correct (add distance above Bench Point)
6. See Supervisor if Northing and Easting do not match
7. See Supervisor if Elevation does not match and Press “Next”
Page 16
SITECH TECHNOLOGY DEALE
R
Page 9
Field Reference Guide
GCS900 Vertical Offset
Version: 13.1
1. Press “F4” to enter Horizontal and Vertical Offset
2. Press “F6” until Vertical Offset is displayed at the top lef t of screen
3. Enter Vertical Offset and Press “F2” to select above or below Design
4. Press “OK” to return to operating screen
5. Vertical Offset is displayed at the bottom of the screen
Page 17
SITECH TECHNOLOGY DEALE
R
Page 10
Field Reference Guide
GCS900 Horizontal Offset
Version: 13.1
1. Press “F4” to enter Horizontal and Vertical Offset
2. Press “F6” until Horizontal Offset is displayed at the top left of screen
3. Press “F1” Alignment:
4. Use Arrows to Select [Plan Line] if list is displayed and Press “OK”
5. Use Arrows to Select Line Offset and Press “F1” Select
Page 18
Page 11
6. Press “OK” and enter Offset distance
7. Press “F2” Select Offset to be Left or Right of the line (-3.00 is Left)
8. Press “OK” to return to operating screen
9. Horizontal Offset is highlighted in red
10. Press “F1” to change Blade Left or Right
Page 19
R
Page 12
GCS900 Vertical Guidance
Version: 13.1
1. Press “Menu”
2. Press “Guidance Method” and Press “OK”
3. Change Adjust cut to avoid overcut: to “NO”
4. Press “F1” for Change Method
5. Select Method from list and Press “OK”
6. Press “OK” to accept change
SITECH TECHNOLOGY DEALE
Field Reference Guide
7. Press “ESC” to return to operating screen
1)
One Point Center is the default setting
used for long or wide surfaces. It also
allows for shaping crowns by holding the
slope past the crown- point.
One Point Focus is used for narrow
surfaces such as shoulders or slopes.
Page 20
SITECH TECHNOLOGY DEALE
R
Page 13
Field Reference Guide
GCS900 Cut and Fill Site Map
Version: 13.1
1. Press “Menu” and select “Mapping/Recording Settings” Press “OK”
2. Change “Mapping for the main screen views” to “Yes” scroll down list
3. Change “Blade tip mapping” to “Automatics on” and Press “OK”
4. Select “Main Screen views” and Press “OK”
5. Under Active views select Cut/Fill “Yes”
6. Under Main Screen Softkeys select Softkey 5 “Mapping On/Off/Auto” and Press “OK”
7. Press “Esc” to Main Screen
8. Press “F5” until Mapping only in Automatic is displayed
9. Press “Next” until Plan View with Cut/Fill Scale is displayed
Page 21
SITECH TECHNOLOGY DEALE
R
Page 14
Field Reference Guide
GCS900 Lane Guidance
Version: 13.1
1. Move Blade Tip with Focus over Lane to be Extended
2. Press “F3” for Lane Guidance
3. “F3” turns Lane Guidance Off and ON
Page 22
SITECH TECHNOLOGY DEALE
R
Page 15
Field Reference Guide
GCS900 Dozer Sensor Calibration
Version: 13.1
1. Press “Menu”
2. Select “Calibrate Sensors” and Press “OK”
3. Select “Blade slope sensor (turn around) and Press “OK”
4. Following instructions
5. Press “F6” Finish
6. Press “ESC” twice to return to operating screen
Page 23
R
Connect to WiFi GCS900
Page 16
Version: 13.1
1. Press “Menu”
2. Press “F2” Installation
3. Select “Connectivity Settings” then press “OK”
4. Select “Wi-Fi Network” then press “OK”
5. Press “F1” New
SITECH TECHNOLOGY DEALE
Field Reference Guide
16 April 2015
6. Select the Wi-Fi you wish to connect to press “OK”
7. Enter “Pass Phrase”
8. Press “F6”
9. Press “F6” Finish
10. Select the Wi-Fi to connect to Press “OK”
11. Press 2 times to return to main menu
Page 24
SITECH TECHNOLOGY DEALE
R
Page 17
Field Reference Guide
TCC Settings GCS900
Version: 13.1
1. Press “Menu”
2. Press “F2” Installation
3. Select “Connectivity Settings” then press “OK”
4. Select “Connected Community Settings” then press “OK”
5. Enter “Device Password” then press “Next”
6. Enter “Organization” then press “Next”
7. “Filespace and Work Group Folder” should be left to default
8. Press “OK”
9. Press 2 times to return to them main screen
Page 25
SITECH TECHNOLOGY DEALE
R
Page 18
Field Reference Guide
Configure Remote Assistant GCS900
Version: 13.1
1. Press “Menu”
2. Press “F2” Installation
3. Select “Connectivity Settings” then press “OK”
4. Select “Remote Assistant Configuration” then press “OK”
5. Enter “Support Number”
6. Press “F1” Force Upgrade
7. Press “OK”
8. Press 2 times to return to main screen
Page 26
SITECH TECHNOLOGY DEALE
R
Page 19
Field Reference Guide
Wireless Data Sync GCS900
Version: 13.1
1. Press “Menu”
2. Press “F2” Installation
3. Select “Connectivity Settings” then press “OK”
4. Select “Wireless Data Sync” then press “OK”
5. Press “F1” Start
6. When synchronization is complete Press “ESC” 3 times to operating screen
Page 27
SITECH TECHNOLOGY DEALE
R
Page 20
Field Reference Guide
Start Remote Assistant GCS900
Version: 13.1
1. Press “Menu”
2. Select “Remote Assistant” then press “OK”
3. Press “F1” Start
4. Once icon appears at the bottom of the screen the machine is connected
5. Press “ESC” 2 times to return to them main screen
Page 28
SITECH TECHNOLOGY DEALE
R
Page 21
Field Reference Guide
Connect to IBSS Base Station GCS900
Version: 13.1
The Control Box must be in Manager’s Mode
1. Press “Menu”
2. Press “F2” Installation
3. Select “Connectivity Settings” then press “OK”
4. Select “GNSS Base Configuration” then press “OK”
5. Select “IBSS-Remote Base”
6. Press “F1” Create New
7. Device Password and Organization should be populated if not see (TCC Settings Sheet)
8. Press “F6”
9. Select the Base from list and Press “F6”
10. Review IBSS Base Name and Press “F6” Finish
11. Select “IBSS - Remote Base”
12. Use left or right arrow keys to select correct base name and Press “OK”
13. Press 2 times to return to operating screen
Page 29
S
ervice and Support
www.sitechrockymtn.com
(866) 903-2335
Service Center Locations:
SITECH Rocky Mountain
2420 Uravan Street
Aurora Co 80011
Loading...