SISTEMATICA S p A NIMBLE User Manual

RTX NIMBLE PLUS

RADIO REMOTE CONTROL 2 COMMAND WITH BUTTONS

USER AND MAINTENANCE MANUAL

This manual is an essential part of the device and it should be thoroughly kept for later consultation.

WARNINGS

Carefully read the warnings contained in this manual, concerning safety and a proper preservation of the
product. These warnings are always to be carefully read before using the device. SISTEMATICA S.p.A.
declines all responsibility for any trouble arising from the non-compliance with these warnings.

• DO NOT TRAVEL WITH THE DEVICE SWITCHED ON

• CONNECT THE SYSTEM ONLY TO THE VEHICLE’S BATTERY

• BEFORE CARRYING OUT ANY MECHANICAL MAINTENANCE OPERATION (WELDING) ON THE

VEHICLE, DISCONNECT THE BATTERY CLIPS

• AVOID ATTEMPTING TO REPAIR THE DEVICE BY YOURSELF. REPAIRS PERFORMED BY

UNSKILLED PEOPLE CAN CAUSE SERIOUS DAMAGES OR FAILURES. FOR ASSISTANCE,
APPLY TO YOUR LOCAL AUTHORIZED SERVICE CENTRE. USE ONLY ORIGINAL SPARE PARTS

• ALWAYS KEEP AT A SAFE DISTANCE FROM THE MOVING PARTS

SISTEMATICA S.p.A.

SISTEMATICA S.p.A. Rev.0

SISTEMATICA S.p.A.SISTEMATICA S.p.A.

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

Rev.0

Rev.0Rev.0

http://www.sistematica.it e-mail: [e-mail] 06/03/2013

the negative

black cable to the negative

TECHNICAL FEATURES

• Number of outputs: 2;

• Frequency bands: ISM 868/915 MHz

• Microprocessor electronics control;

• Dimension: 190x83x22 (with antenna);

• Gradeo of enclosure: IP67;

• Protection of battery inversion polarity;

• 12/24 VDC (10-30 allowed) rating power supply through connection to the vehicle’s battery;

• Typical quiescent current:- 18 mA a 12 V;

- 14 mA a 24 V;

• Interal resettable fuse: 7 A

• Maximum suppliable current for each channel: 5 A

• Maximum total suppliable current: 7 A

• Receiver Category (EN 300-220-1): 2

SYSTEM CODING

It is necessary to code the system only if you have to replace the transmitter unit or if you want to use it with a
different receiver from the one it was purchased with. Follow the instructions to code the system.

1. Take the power supply off the receiver;

2. Disconnect the white or gray cable from negative pole of the battery and connect it to the positive pole of the

battery;

3. Put power into the receiver. The led on the receiver start to blink;

4. Press any 3 keys at the same time on the radio control transmitter within 15 seconds since it has been switched

on (also more times if it is necessary);

5. At this point, the coding occurred. The led on the receiver turn off;

6. Take the power supply off the receiver;

7. Disconnect the white or gray cable from positive pole of the battery and connect it to the negative pole of the

battery;

8. Put power into the receiver with the connector inserted to verify correct operation (press key START on the
transmitter and abilitate the outputs).

For correct use and in order to avoid damage to people or things, it is obligatory to follow these instructions:

1.

Power up the receiver and wait a few swconds

5 WIRES VERSION

INSTRUCTION FOR USE

(the receiver takes a couple of seconds to be
able to operate a sit carries out an self­diagnosis);

2.

Press the required button on the receiver to
activate the related output:
LEFT BUTTON → OUT 1
RIGHT BUTTON → OUT 2

3.

Turn off the receiver after finishing operations.

WIRE FUNCTION

GREEN OUT 1 GREEN OUT 1

pole of the battery.

YELLOW OUT 2 YELLOW OUT 2

WHITE PAIRING WHITE MASTER OUTPUT

RED + ALIMENTATION PINK EMERGENCY OUT

BLACK - ALIMENTATION GRAY PAIRING

RED + ALIMENTATION

SISTEMATICA S.p.A.

SISTEMATICA S.p.A. Pag. 2/4

SISTEMATICA S.p.A.SISTEMATICA S.p.A.

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

To operate from the transmitter, consult the user manual of the transmitter coupled with the
receiver.

http://www.sistematica.it e-mail: [e-mail]

LEFT RIGHT

black cable to

conncet white cable with

NOTE: is necessary

NOTE: is necessary

conncet gray cable with

1.

Power up the receiver and wait a few swconds
(the receiver takes a couple of seconds to be
able to operate a sit carries out an self­diagnosis);

7 WIRES VERSION

2.

Press the required button on the receiver to
activate the related output:
LEFT BUTTON → OUT 1 + M.O. + OUT EM.
RIGHT BUTTON → OUT 2 + M.O. + OUT EM.

3.

Turn off the receiver after finishing operations.

WIRE FUNCTION

pole of the battery.

BLACK - ALIMENTATION

POSI

TIONING OF THE RECEIVER NIBLE

POSITIONING OF THE RECEIVER UNIT, DIMENSION AND DRILLING TEMPLATE

For a proper functioning, locate the receiver type NIMBLE with the cable output downwards, as shown in the picture
below:

The receiver is provided with an integrated antenna; be sure to locate it at sight, not inside any
metal box or screened by ferrous masses (ex. protection carter…)

For the receiver installation use supplied fixing screaw (or equivalent)

DIMENSION DRILLING TEMPLATE NIMBLE

DIMENSION BOX RECEIVER NIMBLE

FUSE

The system is automatically protected from power overload and from possible short-circuit on corresponding outputs
by an internal resettable fuse (7A).

SISTEMATICA S.p.A.

SISTEMATICA S.p.A. Pag. 3/4

SISTEMATICA S.p.A.SISTEMATICA S.p.A.

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail]

PRODUCT IDENTIFYING LABELS

NIMBLE: product model

S/N: product derial number

Cod.: product identification code

RECEIVER IDENTIFICATION LABEL

The system does not respond to the
controls

This product may be subjected to usage restriction. Please contact [e-mail] for any further questions.

These devices complies with Part 15 of the FCC rules.

Removal of the identifying labels entails lapsing of the guarantee conditions and the
responsibility of SISTEMATICA S.p.A. with respect to competent bodies

PROBLEM IDENTIFICATION AND SOLUTION

P

ROBLEM

P

Declaration of conformity for Sistematica S.p.A. products can be required at: [e-mail]

OSSIBLE CAUSES

Absence of power in the receiver
unit

Incorrect connection of the
cabling to the utilities
Incorrect installation of the
receiver
System not coded -Re-code the system (see “CODING THE SYSTEM”)

POSITIONING ON THE RECEIVER OF THE IDENTIFICATION

S

-Check that the emergency mushroom button on the
transmitter is in the release position

-Check that the vehicle battery is correctly connected to
the receiver unit

-Check the cabling to the users (indicators, electro-valves
etc.)

-The receiver must not be shielded by ferrous masses
(see “POSITIONING OF THE RECEIVER UNIT”)

LABEL

OLUTIONS

CE MARK

FCC STATEMENTS

Operation is subject to the following two conditions:
(1) these devices may not cause harmful interference and
(2) these devices must accept any interference received, including interference that may cause undesired operation.

NOTE: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to
these equipment. Such modifications could void the user’s authority to operate the equipments.

SISTEMATICA S.p.A. Grantee Code: O8I

NIMBLE RTX label example
FCC ID: O8INIMBLE

SISTEMATICA S.p.A.

SISTEMATICA S.p.A. Pag. 4/4

SISTEMATICA S.p.A.SISTEMATICA S.p.A.

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail]