SISTEMATICA S p A CONTROLLER4 Users Manual

CONTROLLER 4

RADIO REMOTE CONTROL 4 OUTPUTS

USER AND MAINTENANCE MANUAL

This manual is an essential part of the device and it should be thoroughly kept for later consultation.

WARNINGS

Carefully read the warnings contained in this manual, concerning safety and a proper preservation of the
product. These warnings are always to be carefully read before using the device. SISTEMATICA S.p.A.
declines all responsibility for any trouble arising from the non-compliance with these warnings.

• DO NOT TRAVEL WITH THE DEVICE SWITCHED ON

• CONNECT THE SYSTEM ONLY TO THE VEHICLE’S BATTERY

• BEFORE CARRYING OUT ANY MECHANICAL MAINTENANCE OPERATION (WELDING) ON THE

VEHICLE, DISCONNECT THE BATTERY CLIPS.

• AVOID ATTEMPTING TO REPAIR THE DEVICE BY YOURSELF. REPAIRS PERFORMED BY

UNSKILLED PEOPLE CAN CAUSE SERIOUS DAMAGES OR FAILURES. FOR ASSISTANCE,
APPLY TO YOUR LOCAL AUTHORIZED SERVICE CENTRE. USE ONLY ORIGINAL SPARE PARTS.

• ALWAYS KEEP AT A SAFE DISTANCE FROM THE MOVING PARTS.

SISTEMATICA S.p.A. REV.2a

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail] 11/04/2012

• Manufacturer: SISTEMATICA S.p.A.

• Dimensions: 80x75x55

• Outputs number: up to 4

• IP protection: IP67

• Operating temperature: -20°C ÷ +70°C

• Power supply voltage: 12/24 V ±10%

• Current consumption: - 18 mA at 12 V

- 14 mA at 24 V

Coding the system is an operation that is only necessary when the receiver has to be replaced or you want to use it
with a different SISTEMATICA radio remote control from the one it is coupled with at the time of purchase.
For a correct coding procedure, perform the following steps:

1. Disconnect the power to the receiver;

2. Open the receiver box, by unscreawing the 4 screws fixed on

its top;

3. Locate and press the coding pushbutton on the receiver board
(blue button – fig. 1);

4. Put power into the receiver by keeping the coding pushbutton
pressed for 3-4 sec.; the yellow led on the receiver board
flashes two time per second; so release the coding pushbutton;

5. Press any 3 keys at the same time on the transmitter within 15
seconds since it has been switched on (also more time if it is
necessary; the yellow led stop to blink);

6. At this time, the transmitter is codified with the reveiver; check
all the system function by trying the movements of the system;

7. Close the receiver box.

The standard wiring is composed of a cable of lenght L=1mt with a termination in the receiver on one side and free
cables on the other side

TECHNICAL FEATURES

• Max current per channel: 5 A

• Max total current: 20 A

• Communication interface (when applicable): CAN

BUS

• 8 bit microcontroller

• Reverse battery protection

• Internal antenna

SYSTEM CODING

WIRING DESCRIPTION

COLOR FUNCTION

GREEN EV 1

YELLOW EV 2

GRAY EV 3

PINK EV 4
RED + ALIMENTATION

BLACK - ALIMENTATION

Figure 1. Coding pushbutton

SISTEMATICA S.p.A. Pag. 2/4

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail]

For a proper functioning, locate the receiver type CONTROLLER 4 with the cable output downwards, as shown in

POSITIONING OF THE RECEIVER UNIT, DIMENSION AND DRILLING TEMPLATE

the picture below:

The receiver is provided with an integrated antenna; be sure to locate it at sight, not inside any
metal box or screened by ferrous masses (ex. Protection carter...)

POSITIONING OF THE CONTROLLER 4

RECEIVER DIMENSION

The system is automatically protected from power

FUSE REPLACEMENT

overload and from possible short-circuit on
corresponding outputs. For further protection is also
provided an internal fuse within the box. For replacing
the damaged fuse, please proceed as follows:

1. Disconnect the power to the receiver;

2. pen the receiver box, by unscreawing the 4 screws

fixed on its top;

3. Locate the damage fuse on the receiver board;

4. Take the damaged fuse out of its holder and insert

the new fuse (F1= 10 A);

5. Put power into the receiver; to check that the fuse
has been correctly replaced, try one or more
movements of the system;

6. Close the receiver box.

DRILLING TEMPLATE DIMENSION

PRODUCT IDENTIFYING LABELS

nnnnn: product model

Internal label

External label

S/N: product serial number

Cod.: product identification number

Removal of the identifying labels
entails lapin of the guarantee
conditions and the responsabilità of
SISTEMATICA S.p.A. with respect to
component bodies

SISTEMATICA S.p.A. Pag. 3/4

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail]

P

ROBLEM

POSSIBLE CAUSES SOLUTIONS

The system does not
respond to the controls

The GREEN led on the
remote control does not
light up when a key is
pressed

The system responds to
the controls in a
discontinuous way

PROBLEM IDENTIFICATION AND SOLUTION

-Check that the emergency mushroom button on the transmitter

Absence of power in the receiver
unit

(if present) is in the release position.

-Check that the vehicle batterie is correctly connected to the
receiver unit

-Check that the fuse inside the receiver unit is inctact, and if it is

not, replace it (see “FUSE REPLACEMENT”)
Incorrect connection of the
cabling to the utilities
Incorrect installation of the
receiver

Incorrect replacement of the
batteries

-Check the cabling to indicators, electro-valves etc.

-The receiver must not be shielded by ferrous masses (see

“POSITIONING OF THE RECEIVER UNIT”)

-Check that the batteries have been inserted correctly; if

necessary replace them (see “REPLACEMENT THE

BATTERIES” on the manual of the transmitter combined)
System not coded -Re-code the system (vedi “CODIFYING THE SYSTEM”)

Blown fuse

-Replacement of the fuse on the receiver board (see “FUSE

REPLACEMENT”)
Flat batteries

Flat batteries

-Replacement of the transmitter batteries (vedi “REPLACEMENT

THE BATTERIES” on the manual of the transmitter combined)

Batteries almost flat
Using the transmitter beyond its
maximum range
Connection to the battery and to
the utilities made with cables of
unsuitable section or lenght

-Keep to a distance ≤ 120m from the receiver

-Chech that the connection to the battery and the utilities are

made with cables of suitable section and lenght

CE MARK

Declaration of conformity for Sistematica S.p.A. products can be required at: [e-mail]

This product may be subjected to usage restriction. Please contact [e-mail] for any further questions.

These devices complies with Part 15 of the FCC rules.

FCC STATEMENTS

Operation is subject to the following two conditions:
(1) these devices may not cause harmful interference and
(2) these devices must accept any interference received, including interference that may cause undesired operation.

NOTE: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to
these equipment. Such modifications could void the user’s authority to operate the equipments.

SISTEMATICA S.p.A. Grantee Code: O8I

TRENDRTX label example
FCC ID: O8ICONTROLLER4

SISTEMATICA S.p.A. Pag. 4/4

Via S. Pertini, 17 – 12030 MANTA (CN) ITALY Tel. [phone] r.a. – Fax [phone]

http://www.sistematica.it e-mail: [e-mail]