Sirman SIGIX M20 Instruction Manual For Use And Maintenance
20
SERVICE CENTRE
AUTHORISED DEALER
Tray thermo-sealer CE professional
Instruction Manual, for Use and Maintenance
SIGIX M20
Ed. 03/2016
2 19
To proceed with the cleaning of the
machine from the outside, use a slightly
soaked sponge with a small quantity of
detergent and an odourless and nonharmful sanitizer.
Do not use abrasive detergents, antiscaling detergent creams, solvents and
diluents; the residues of such products
may dangerously contaminate food
substances during following processing.
ATTENTION!
pH7
Fig. n°34
ATTENTION!
CHAP. 12 - DISMANTLING
12.1 - DECOMMISSIONING
If, for some reason, it is decided to disable the machine, make sure that it cannot
be used by any person: disconnect and cut electrical connections.
12.2 - WEEE Waste of electric and electronic equipment
In accordance with art.13 of the Legislative Decree dated 25 July
2005 ,n.151 ”Implementation of Directives 2002/95/CE, 2002/96/CE e
2003/108/CE, relating to the reduction of the use of hazardous substances
in electrical and electronic equipment, as well as to waste disposal”.
The symbol of the crossed out waste bin on the product and its packaging indicates that at the end of its useful life, the product must be disposed of separately
from other waste.
Sorted waste disposal of products at the end of their useful life is organised and
managed by the manufacturer. The user should dispose of this equipment contacting the manufacturer and following the system adopted by the latter to allow
the separate collection of the equipment at the end of its service life.
The suitable recycling for a further conveyance of the dismantled equipment, to
recycling, to treatment and to environmentally compatible disposal contributes to
avoid possible negative effects on the environment and on health and promotes
the re-use and/or recycling of materials, of which the equipment is made.
The illegal disposal of a product is punishable according to the laws
currently in force.
18
Fig. n°33
CHAP. 11 – ROUTINE CLEANING
11.1 - GENERALS
- Machine cleaning is an operation, which must be carried out, in case of contact
with the processed product.
- The tray sealers must not be cleaned with high pressure water jet cleaners or
water jets, but with neutral detergents (pH 7). Any other detergent product is
forbidden. Tools, scrubbing brushes and other may damage the surface of the
machine.
Before performing any cleaning operation, it is necessary to:
- disconnect the power supply plug from the mains to completely isolate
the rest of the system and wait for it to cool off.
11.2 – MACHINE CLEANING
The cleaning of the drawer must be carried out in case of need and it must be
performed with hot water and with the support of a sponge. Carefully dry each
element, at the end of the cleaning operation.
Error Cause Solutions
E1
Wait for the machine to be in the READY
mode to seal the tray correctly.
E2
A series of consecutive
“beep” signals during
sealing
The sealing operation has not been
completed correctly It is advisable to
perform the operation again.
CHAP. 10 – ISSUES AND SOLUTIONS
(See Fig. n°33)
10.1 – POSSIBLE ERRORS
WAIT 4.0 175°
0001 130°
READY 4.0 175°
0001 130°
3
FOREWORD
This manual has been drafted in order to provide the Customer with al l the informatio n
on the machine and on the relating safety regulations, as well as all use and
maintenance instructions, allowing to use the means in the best way possible,
preserving efficiency intact in the course of time.
This manual must be kept and preserved intact until machine disposal.
This manual is delivered to the staff assigned to use the machine and perform the
routine maintenance.
INDEX OF CHAPTERS
CHAP. 1 - MANUAL page 5
1.1 - PURPOSE
1.2 - USERS
1.3 - USE AND PRESERVATION
1.4 - MANAGEMENT AND RESPONSIBILITY
CHAP. 2 – INFORMATION ON THE MACHINE page 6
2.1 - GENERAL PRECAUTIONS
CHAP. 3 – TECHNICAL SPECIFICATIONS page 7
3.1 - SAFETY DEVICES INSTALLED ON THE MACHINE
3.1.1 - Safety electrical devices
3.2 - WARNING SIGNS
CHAP. 4 – ABOUT THE MACHINE page 9
4.1 - DESIGN FEATURES
4.2 - DESCRIPTION OF THE MACHINE
4.3 - COMPOSITION OF THE MACHINE
CHAP. 5 – TRASPORT PACKAGING AND UNPACKAGING page 10
5.1 - PACKING
5.2 - CHECK OF THE PACKAGING UPON RECEIPT
5.3 - UNPACKAGING
CHAP. 6 – TECHNICAL DATA page 12
6.1 - SIZE REQUIREMENT, WEIGHT AND FEATURES
CHAP. 7 – INSTALLATION page 13
7.1 - POSITIONING
7.2 - ELECTRICAL CONNECTION
7.2.1 - Monophase sealer
7.3 - WIRING DIAGRAM MONOPHASE 230V
CHAP. 8 – USE OF THE MACHINE page 14
8.1 - POSITIONING OF THE FILM
8.1.2 - Positioning of the mould
8.2. - PRELIMINARY CHECKS
Loading...