Page 1
USE
R INSTRUCTIONS
Hand Sealer
Mod. S300/2 - S400/2 - S400/2T
Page 2
Page 3
HAND SEALER 300 / 400 / 400 T
BE
FORE USE
eale
- Locate the s
- Connect to correct voltage power supply (see data plate for correct voltage).
- Power will only be used on impulse when handle is pushed down.
CAUTION!
- Do not use outdoors or in a wet or humid location.
- If an extension lead is used, ensure that it is undamaged, and the plug is c
- W
hen sealing all films it is most important to keep timer to the minimum.
- Start by setting timer knob to lowest setting and test on the film then increase by small
increments until a satisfactory seal is achieved.
- Operating the sealer at too high a setting in relation to the thickness and type offilm being
used or without any film at all, will burn the upper Teflon and cause the heating element to fail
prematurely.
OPERATION
- Place a polybag or film over the heating element at the desired seal location.
- Press
out once seal time is completed. Leave handle down momentarily after light goes out to
allow film to cool. Do not use undue pressure.
- Inspect the seal. If the seal does not appear to be fully welded and pulls apart, adjust the
timer knob to a higher setting.
If the seal appears broken and overheated or the polybag/film sticks to the s
pressure pad beneath the lever, adjust the timer knob to a lower setting; or allow longer cooling
time between seals.
the handle down firmly for 1-2 seconds. Indicator light will illuminate and goes
r on a level surface, in a dry area.
orrectly wired.
ilicon rubber
TIMER SETTINGS
- The machine will seal all types of Polyethylene, LDPE and Polypropylene in sheets
or bag form.
- The timer is infinitely variable in 9 settings to accommodate the various thickness and types of
material being used.
- Simply adjust timer to suit gauge of film in use until the desired seal strength is obtained.
- Please, ensure that the material is kept completely flat across the Teflon fabric to obtain
maximum seal efficiency.
Page 4
- Depending on types
of 25 micron (
MODEL
HAND SEALER 2mm / 2mm T
of material used this unit will seal from two layers
100 gauge) up to 2 x 200 micron (2 x 800 gauge).
FOR BEST RESULTS
- Keep the Teflon fabric cover over the heating element clean and free of
c
ontamination. If it is damaged replace it immediately.
eep the silicon rubber Pressure Pad free of contamination, replace if damaged, or remove
K
-
and use other side.
Allow at least one second “cooling time” between operations. Daily operations should
-
not exceed 1000. Your sealer is designed for long trouble free service. Should a
malfunction occur, the following may assist you in locating the fault.
AP
PARENT POWER FAILURE
(Indicator light does not come on when handle is pressed)
CHECK THE FOLLOWING
- Switch at wall socket is on.
- Plug fuse has not blown.
- Power supply cord is not damaged.
AND RELIABLE OPERATION
INDICATOR LIGHT COMES ON BUT NO WELD
CHECK THE FOLLOWING
- Inspect heating element for breaks. Replace if necessary.
IMPERFECT WELD
CHECK THE FOLLOWING
- Ins
- Inspect silicon rubber pressure pad for damage. Replace if necessary.
- Inadequate “cooling time”. Allow at least one second between operations.
- Eventually certain components such as the heater element and the Teflon fabric heater
pect Teflon fabric heating element cover for breaks or damage. Replace if necessary.
cover will require replacement through “normal wear and tear”
Page 5
- Inspect lower Teflon , replace if worn otherwise element will short out
on body of machine.
To replace the Tef
Disconnect machine from mains supply. Remove the screws that locate the retaining plates. The
Teflon fabric can be lifted clear and replaced by a new part and the retaining plate and screws
replaced.
TECHNICAL DATA
Power
Sealing temperature
Sealing time
Adjust
time
able sealing
lon fabric heater cover
S
300/2
watt
°C
ec.
s
s
ec.
150 max 150 max 150 max
in. 0,5
m
ax 2,5
m
S
400/2
510 700 700
in. 0,5
m
ax 2,5
m
1,5 1,5 1,5
S
400/2T
c/cutter
in. 0,5
m
ax 2,5
m
Sealing thickness
Sealing length
Dimensions
Net weight
Sealing material
m
m
mm
m
m
g
k
0,5
2 x
300-400
455x75 h.210
open
3,5 4 4
0,5 0,5
2 x
300-400
555x75 h.210
open
E, PP, LDPE, PVC
P
2 x 300-400
555x75 h.210
open
Page 6
Page 7
xploded view legend
E
1 Body 17 Bracket
2 Teflon tape 18 S
3 Heating element 19 K
4 Teflon cloth 20 P
5 Cover 21 P
6 Tr
7 Fix
8 Heat holder 24 S
ansformer
er for transformer
22 P
23 P
ealing arm
nob
laten holder
laten spring
laten
laten pin
ilicon rubber
9 Was
10 Led 26 S
11 Resistance 27 Sealing arm spring
12 Controller 28 P
13 Plate board 29 V
14 Bottom plate 30 Holder for cutter
15 Power board 31 Cutter
her
25 S
ealing arm pin
witch lever
ower cord
olume knob
16 M
icro switch
32 B
ushing for power
Page 8
SERVICE
AUTHORISED
CENTRE
DEALER
Loading...