Sirkom SRK-1080P-F User Manual
SIRKOM SRK-1080P-F
User Manual
Jul 27, 09
FCC Notices
It’s herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation
is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
residential installation. This equipment generated uses and can radiate radio frequency
energy and if not installed and used in accordance with the instruction manual may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio of television reception, which can be determined by turning the
equipment off or on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
CE Declaration
This device complies with CE class B.
EN55022 IEC 61000-4-4
EN61000-3-2 IEC 61000-4-5
EN61000-3-3 IEC 61000-4-6
EN55024 IEC 61000-4-8
IEC 61000-4-2 IEC 61000-4-11
IEC 61000-4-3
Printed in Spain
All contents are subject to change without notice.
All trademarks are the property of their respective owner.
1. Package Contents……………………..……………………….. 1
2. Introduction……………………………….……………………... 1
3. Features………………………………………….……………… 2
4. Hardware Overview…………………..………………………... 3
5. Remote Control…………………………..…………………….. 4
5.1 Entering Text or IP Address…………..…………………… 4
6. Start the SRK-1080P-F…………….………………………. 5
7. Setting Up……………………………………………………….. 6
7.1 Network Setup……………………..….……………………. 6
7.2 FTP Setup…………………………………………………… 8
7.3 Video Setup…………………………..…………………….. 10
7.4 Other Setup………………………………..……………….. 11
8. Using the SRK-1080P-F………………..…………………... 13
8.1 Play Media Files on the CF Card…………………………. 13
8.2 Download Function…………………………………………. 16
8.3 Play the Media Files on the PC…………………………… 19
8.4 Download/ Upload Media Files…………….……………… 22
8.5 RS-232 Function……………………………………..…….. 25
9. Http Command Function………….………………..………….. 26
9.1 Player Control………………….………………..………….. 27
9.2 Network Setup…………………………………..………….. 28
9.3 Timer Setup………………………………………..……….. 29
10. GPS Function……………....…..…………..……….………….. 30
11. Troubleshooting……………………..……..………..………….. 32
CONTENTS
1
1. PACKAGE CONTENTS
1. SRK-1080P-F
2. GPS Antenna
3. Remote Control
4. Audio Cable
5. S-Video Cable
6. Power Adapter
7. User Manual
2. INTRODUCTION
SIRKOM SRK-1080P-F is a full HD digital signage that built-in Global Positioning System
(GPS) module. SIRKOM SRK-1080P-F will receive the microwave signal from satellites and
continuously provide the current location positioned and play the associated media file according
to its location.
SIRKOM SRK-1080P-F can play HD WMV9 and WMA files from CF memory card without a
computer. SIRKOM SRK-1080P-F supports High Definition movie hardware decode acceleration,
presents for you the smoother and clearer picture, it supports high resolution video output such as
1080P / 1080i / 720P for movie theater quality video on a big screen. By connecting to S-Video,
Y.Pb.Pr, VGA (resolution up to 1360 x 768), HDMI (1920 x 1080P) and Audio, you can play media
files on any display device.
SIRKOM SRK-1080P-F can be installed on the tourist bus, train or taxi to play the local
attractions, station information or latest promotion.
2
3. FEATURES
Built-in Global Positioning System (GPS) module that receive the microwave signal from
satellites and play the associated media file according to its location.
Supports multiple file formats: HD WMV9 and WMA.
Supports Video, S-Video, Y.Pb.Pr, HDMI, VGA and Audio output.
HD Y.Pb.Pr output supports resolution: NTSC Mode(60Hz): 480P/ 720P/ 1080i.
PAL Mode(50Hz): 576P/ 720P/ 1080i.
HDMI Output: 480P/ 720P/ 1080i/ 1080P.
VGA output supports resolution: 640x480/ 800x600/ 1024x768/ 1280x1024/ 1360x768.
Supports RS-232 port for computer control with ASCII command (play, stop, pause…etc).
Supports CF memory card. (Suggest using the high speed (150X) CF card)
The source of HD WMV9 MP@HL (Main Profile / High Level) supports resolution up to
1920x1080 (1080P) and the maximum bit rate is 12Mbps.
Exports the Configuration Value: You can export the configuration value to the CF card. The
configuration value can be modified on your PC, and can be applied to the SRK-1080P-F or
others.
Supports Auto Key Lock function.
Connect using an Ethernet network cable at up to 100Mbps.
Supports HTTP Command function.
Compatible with Windows Media Player 11: Play media files stored in a network computer.
Supports FTP Auto Download Function: Connect to Remote FTP server and download data to
the CF card automatically.
Supports Download Pause / Resume Function: Continue unfinished downloads upon next
session.
Embedded FTP Server.
Supports NTP Network (G.M.T) Timer. You can also set the system time manually.
Supports Universal Plug and Play (UPnP) and DHCP.
Supports SLIDE SHOW Function.
3
4. HARDWARE OVERVIEW
Power Switch: Toggle between main power on & off.
DC Input: For the power adapter. (DC 12V / 1.5A)
VGA Out: Connects to devices that support VGA input. (LCD、projector)
Y.Pb.Pr Out: Connects to devices that support Y.Pb.Pr input. (HDTV、projector)
HDMI Out: Connects to devices that support HDMI input.
RS-232 Connector: Used for computer control with ASCII command.
RJ-45 Ethernet Connector: Connects to router or PC by RJ-45 Cable.
Audio Out: Connects to sound input. (HDTV with amplified speaker)
S-Video Out: Connects to devices that support S-Video input. (HDTV、projector)
Video Out: Connects to device that support Video input. (HDTV、projector)
GPS Antenna Connector: Connects to the provided GPS antenna.
“CF READY” LED: Steady green confirms that the CF card is inserted correctly.
CF Card Socket: Insert your CF card with media files.
“RESET” Button: To restart the SRK-1080P-F.
4
5. REMOTE CONTROL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Power on/ off
Select the output mode
Numeric Key
Delete last entry
Select a function or to play the selected file
Open the setup menu Mute sound
OSD display function on/ off
Auto-play function on/ off
Mute sound
Volume up/ down
Move the cursor
Confirm the selection/ entry
Go back one layer
Select the TV type (NTSC/ PAL)
Shuffle on & off
Play the file selected
View the previous/ next file
Play the previous/ next file if in playback
Select the repeat mode
Rewind/ forward movie or music files
Stop playback
Show the information of the file selected
Search video (movie) timeframe
Zoom in/ out on the movie or picture
Pause the playback or play frame by frame
5.1 ENTERING TEXT OR IP ADDRESS
Keys need to be pressed multiple times to enter the letter corresponding to that key.
For Example: To enter the letter “a”. You would press the button “2” twice.
Enter The IP Address
For Example: To enter the IP address”192.168.100.100”,
Step 1: Press “1” once, then “1” is displayed, and the color of “1” is orange.
Step 2: When the color of “1”turns white, press “9” once, then “9” is displayed.
Step 3: Repeat steps 1 and 2 to enter and complete the IP address.
5
6. START THE SRK-1080P-F
Power On
Insert the CF memory card that has Picture, Music, Movie or WMV9 files.
Press the “POWER” button to power on the SIRKOM SRK-1080P-F, and then press the “TV
MODE” button to select the output mode.
NOTE: The SRK-1080P-F can’t be turned on without inserting the CF card.
Status After Power On
Status 1: If the “AUTOPLAY (Movie, Picture or All Files)” function is enabled and there are
media files on the CF card, the SIRKOM SRK-1080P-F will auto play media files after power
on.
Status 2: If the “AUTOPLAY” function is disabled, after power on the main menu will appear
as shown in the following figure. There are two groups in the main menu (“/mnt/CF” and
“SETUP”).
NOTE: The pop-up window that shows the IP address will appear later, if DHCP mode is selected
when the SIRKOM SRK-1080P-F is turned on.
Power Off: Press the “POWER” button again to power off.
6
7. SETTING UP
In the main menu, using the “▼” button on remote control to select the “SETUP” item, and then
press the “ENTER” button. You will be presented with the SRK-1080P-F settings screen.
You can also press the “SETUP” button on remote control to directly open the settings screen.
(If there is file that is being play, please stop first.)
There are four groups of sub-menu in the main menu (“Network Setup”, “FTP Setup”, “Video
Setup” and “Other Setup”).
In the settings screen, you can use the “▲、▼、▲、▼” buttons to select an item, and press the
“ENTER” button to confirm the selection.
Press the “SETUP” button on remote control to save and quit the settings screen.
7.1 NETWORK SETUP
Network with: Select your network connection Disable/ RJ45.
IP Assigned by DHCP: If you have a DHCP-enabled router, please select “On”, and then the
router will automatically assigns an IP address to the SIRKOM SRK-1080P-F. If you don’t have
a DHCP –enabled router, select “Off” and type the network information in “Assign IP Address”.
7
7.1 NETWORK SETUP (continued)
Assign IP Address: If the SIRKOM SRK-1080P-F is connected to a network without a DHCP
server or you want to use Local FTP Server function, enter the fixed IP address, Mask, Gateway
and DNS for the SIRKOM SRK-1080P-F.
PS. Refer to 5.1 for how to enter IP address by remote control.
NOTE: Before setting the IP address, Mask, Gateway and DNS, check the network information of
your PC. Please follow the steps below to get the network information of your PC.
Step 1: Click on “Start” → “Run” and type in “command”, then press “ENTER”.
The MS-DOS window will appear, type in “ipconfig” and then press “ENTER” to get the network
information.
Step 2: Assign IP Address, Mask (Subnet Mask) and Gateway (Default Gateway) for the
SRK-1080P-F.
Enter the same values of the Subnet Mask and Gateway, and be careful not to enter the values of
IP address that are already used by other devices on the network.
Media Player 11 Server: Enable/ disable the Media Player 11 server.
8
7.2 FTP SETUP
Local FTP Server: Turn on/ off the SIRKOM SRK-1080P-F server.
(If you use the SIRKOM SRK-1080P-F server, please disable the DHCP function and input a
fixed IP address, Mask, Gateway and DNS of the SIRKOM SRK-1080P-F)
Local FTP Server Setup: Set the “Port”, “User ID” and “Password” of the SIRKOM
SRK-1080P-F.
(The Default Port: 21, User ID: root, Password: admin)
FTP Auto Download: Enable/ Disable the FTP auto download function.
Remote FTP Download Setup
- Server IP: Enter the domain name or IP address of the FTP as was given to you by your
Web hosting provider.
- Port: The default port for FTP is 21. In most cases you should not change this number. If
the FTP site uses a port other than 21, you should enter the correct port.
- User ID: Enter the user name of the Remote FTP server.
- Password: Enter the Password of the Remote FTP server.
- FTP Path: Enter the folder path that you want to share.
NTP Server: Enable/ Disable the NTP server function. (if the SRK-1080P-F isn’t connect to
internet, please disable the NTP Server function)
Time Setup: Set the NTP Server, Local Time and Auto Download Time here.
① NTP Server (the SIRKOM SRK-1080P-F must be already connected to the network)
- NTP Server: Enter the NTP server IP address like: 204.152.184.72.
- G.M.T: After SRK-1080P-F get the time from NTP server, it will update the G.M.T field.
- Time Zone: Use the Volume +, - and Numeric Key to set the time zone of your location.
(time zone must be set properly for the Auto-Download and Schedule functions)
9
NOTE: GMT and applied regions
Time Zone Region Time Zone Region
(GMT-12:00) Eniwetok, Quazalen (GMT+02:00) Helsinki, Riga, Tallinn
(GMT-11:00) Midway, Ireland, Samoa (GMT+03:00) Nairobi
(GMT-10:00) Hawaii
(GMT+03:00)
Moscow, Saint Petersburg,
Volgograd
(GMT-09:00) Alaska (GMT+03:00) Baghdad
(GMT-08:00)
Pacific GMT (U.S. & Canada);
Tijuana
(GMT+03:00) Kuwait, Raid
(GMT-07:00)
Continental GMT (U.S. &
Canada)
(GMT+03:30) Tehran
(GMT-07:00) Arizona (GMT+04:00) Baku, Tbilisi, Ere van
(GMT-06:00) Mexico city (GMT+04:00) Abu Dhabi, Muscat
(GMT-06:00) Saskatchewan (GMT+04:30) Kabul
(GMT-06:00)
Eastern Coast GMT (U.S. &
Canada)
(GMT+05:00) Yekaterinburg
(GMT-06:00) Indiana (Eastern Coast) (GMT+05:00) Islamabad, Karachi, Tashkent
(GMT-04:00) Atlantic GMT (Canada)
(GMT+05:30)
Calcutta, Chennai, Mumbai, New
Delhi
(GMT-04:00) Santiago (GMT+05:45) Katmandu
(GMT-04:00) Caracas, La Paz (GMT+06:00) Sri Jayewardenepura Kotte
(GMT-04:00) Newfoundland (GMT+06:00) Astana, Dakar
(GMT-03:00) Greenland (GMT+08:00) Irkutsk, Ulan Bator
(GMT-03:00) Buenos Aires, Georgetown (GMT+08:00) Kuala Lumpur, Singapore
(GMT-03:00) Brasilia (GMT+08:00) Taipei
(GMT-02:00) Mid-Atlantic (GMT+08:00) Perth
(GMT-01:00) Capo Verde Is. (GMT+09:00) Seoul
(GMT-01:00) Azores (GMT+09:00) Yakutsk
(GMT-00:00)
Greenwich GMT; Dublin,
Edinburgh, Lisbon, London
(GMT+09:00) Osaka, Sapporo, Tokyo
(GMT-00:00) Casablanca, Monrovia (GMT+09:30) Darwin
(GMT+01:00)
Beograd, Bratislava, Budapest,
Ljubljana, Prague
(GMT+09:30) Adelaide
(GMT+01:00)
Brussels, Copenhagen, Madrid,
Paris
(GMT+10:00) Guam, Port Moresby
(GMT+01:00)
Sarajevo, Skopje, Sofia, Vilnius,
Warsaw, Zagreb
(GMT+10:00) Brisbane
(GMT+01:00) Midwest Africa (GMT+10:00) Vladivostok
(GMT+01:00)
Amsterdam, Berlin, Bern, Rome,
Stockholm, Vienna
(GMT+10:00) Canberra, Melbourne, Sydney
(GMT+02:00) Bucharest (GMT+10:00) Hobart
(GMT+02:00) Athens, Istanbul, Minsk
(GMT+11:00)
Magadan, Solomon Is., New
Caledonia
(GMT+02:00) Jerusalem (GMT+12:00) Auckland, Wellington
(GMT+02:00) Cairo
(GMT+12:00)
Fiji, Kamchatka Pen., Marshall
Is.
(GMT+02:00) Harare, Pretoria (GMT+13:00) Nuku'alofa
Loading...